257 lines
7 KiB
C
257 lines
7 KiB
C
|
/**
|
||
|
|
* Marlin 3D Printer Firmware
|
||
|
|
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
||
|
|
* Copyright (C) 2017 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
||
|
|
*
|
||
|
|
* Based on Sprinter and grbl.
|
||
|
|
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
|
||
|
|
*
|
||
|
|
* This program is free software: you can redistribute it and/or modify
|
||
|
|
* it under the terms of the GNU General Public License as published by
|
||
|
|
* the Free Software Foundation, either version 3 of the License, or
|
||
|
|
* (at your option) any later version.
|
||
|
|
*
|
||
|
|
* This program is distributed in the hope that it will be useful,
|
||
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||
|
|
* GNU General Public License for more details.
|
||
|
|
*
|
||
|
|
* You should have received a copy of the GNU General Public License
|
||
|
|
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||
|
|
*
|
||
|
|
*/
|
||
|
|
|
||
|
|
/**
|
||
|
|
* MKS SBASE pin assignments
|
||
|
|
*/
|
||
|
|
|
||
|
|
//#if !defined(TARGET_LPC1768)
|
||
|
|
#if DISABLED(IS_REARM)
|
||
|
|
#error "Oops! Make sure you have Re-Arm selected."
|
||
|
|
#endif
|
||
|
|
|
||
|
|
#ifndef BOARD_NAME
|
||
|
|
#define BOARD_NAME "MKS SBASE"
|
||
|
|
#define DEFAULT_WEBSITE_URL "https://github.com/makerbase-mks/MKS-SBASE"
|
||
|
|
#endif
|
||
|
|
|
||
|
|
#define LARGE_FLASH true
|
||
|
|
|
||
|
|
// unused
|
||
|
|
/*
|
||
|
|
#define D57 57
|
||
|
|
#define D58 58
|
||
|
|
*/
|
||
|
|
|
||
|
|
|
||
|
|
//
|
||
|
|
// Servos
|
||
|
|
//
|
||
|
|
|
||
|
|
|
||
|
|
//
|
||
|
|
// Limit Switches
|
||
|
|
//
|
||
|
|
#define X_MIN_PIN 3 //10k pullup to 3.3V, 1K series
|
||
|
|
#define X_MAX_PIN 2 //10k pullup to 3.3V, 1K series
|
||
|
|
#define Y_MIN_PIN 14 //10k pullup to 3.3V, 1K series
|
||
|
|
#define Y_MAX_PIN 15 //10k pullup to 3.3V, 1K series
|
||
|
|
#define Z_MIN_PIN 19 //The original Mks Sbase DIO19 has a 10k pullup to 3.3V or 5V, 1K series, so when using a Zprobe we must use DIO41 (J8 P1.22)
|
||
|
|
#define Z_MAX_PIN 18 //10k pullup to 3.3V, 1K series
|
||
|
|
|
||
|
|
|
||
|
|
|
||
|
|
//
|
||
|
|
// Steppers
|
||
|
|
//
|
||
|
|
#define X_STEP_PIN 26
|
||
|
|
#define X_DIR_PIN 28
|
||
|
|
#define X_ENABLE_PIN 24
|
||
|
|
|
||
|
|
#define Y_STEP_PIN 54
|
||
|
|
#define Y_DIR_PIN 55
|
||
|
|
#define Y_ENABLE_PIN 38
|
||
|
|
|
||
|
|
#define Z_STEP_PIN 60
|
||
|
|
#define Z_DIR_PIN 61
|
||
|
|
#define Z_ENABLE_PIN 56
|
||
|
|
|
||
|
|
#define E0_STEP_PIN 46
|
||
|
|
#define E0_DIR_PIN 48
|
||
|
|
#define E0_ENABLE_PIN 62
|
||
|
|
|
||
|
|
#define E1_STEP_PIN 36
|
||
|
|
#define E1_DIR_PIN 34
|
||
|
|
#define E1_ENABLE_PIN 30
|
||
|
|
|
||
|
|
|
||
|
|
#define X2_STEP_PIN 36
|
||
|
|
#define X2_DIR_PIN 34
|
||
|
|
#define X2_ENABLE_PIN 30
|
||
|
|
|
||
|
|
|
||
|
|
//
|
||
|
|
// Temperature Sensors
|
||
|
|
// 3.3V max when defined as an analog input
|
||
|
|
//
|
||
|
|
|
||
|
|
|
||
|
|
#define TEMP_0_PIN 0 //A0 (TH1)
|
||
|
|
#define TEMP_BED_PIN 1 //A1 (TH2)
|
||
|
|
#define TEMP_1_PIN 2 //A2 (TH3)
|
||
|
|
#define TEMP_2_PIN 3 //A3 (TH4)
|
||
|
|
|
||
|
|
|
||
|
|
//
|
||
|
|
// Heaters / Fans
|
||
|
|
//
|
||
|
|
|
||
|
|
#define HEATER_BED_PIN 10
|
||
|
|
#define HEATER_0_PIN 8
|
||
|
|
#define HEATER_1_PIN 59
|
||
|
|
#define FAN_PIN 9
|
||
|
|
|
||
|
|
|
||
|
|
#define PS_ON_PIN 69
|
||
|
|
|
||
|
|
|
||
|
|
//
|
||
|
|
// Connector J7
|
||
|
|
//
|
||
|
|
|
||
|
|
// 5V
|
||
|
|
// NC
|
||
|
|
// GND
|
||
|
|
#define PIN_P0_17 50
|
||
|
|
#define PIN_P0_16 16
|
||
|
|
#define PIN_P0_14 80
|
||
|
|
|
||
|
|
|
||
|
|
//
|
||
|
|
// Connector J8
|
||
|
|
//
|
||
|
|
|
||
|
|
// GND
|
||
|
|
#define PIN_P1_22 41
|
||
|
|
#define PIN_P1_23 53
|
||
|
|
#define PIN_P2_12 12
|
||
|
|
#define PIN_P2_11 35
|
||
|
|
#define PIN_P4_28 13
|
||
|
|
|
||
|
|
|
||
|
|
//
|
||
|
|
// Prusa i3 MK2 Multi Material Multiplexer Support
|
||
|
|
//
|
||
|
|
|
||
|
|
|
||
|
|
#define E_MUX0_PIN 50 // J7-4
|
||
|
|
#define E_MUX1_PIN 16 // J7-5
|
||
|
|
#define E_MUX2_PIN 80 // J7-6
|
||
|
|
|
||
|
|
|
||
|
|
/**
|
||
|
|
* Smart LCD adapter
|
||
|
|
*
|
||
|
|
* The Smart LCD adapter can be used for the two 10 pin LCD controllers such as
|
||
|
|
* REPRAP_DISCOUNT_SMART_CONTROLLER. It can't be used for controllers that use
|
||
|
|
* DOGLCD_A0, DOGLCD_CS, LCD_PINS_D5, LCD_PINS_D6 or LCD_PINS_D7. A custom cable
|
||
|
|
* is needed to pick up 5V for the EXP1 connection.
|
||
|
|
*
|
||
|
|
* SD card on the LCD uses the same SPI signals as the LCD. This results in garbage/lines
|
||
|
|
* on the LCD display during accesses of the SD card. The menus/code has been arranged so
|
||
|
|
* that the garbage/lines are erased immediately after the SD card accesses are completed.
|
||
|
|
*/
|
||
|
|
|
||
|
|
#if ENABLED(ULTRA_LCD) //
|
||
|
|
|
||
|
|
#define BEEPER_PIN 49 // EXP1.1
|
||
|
|
|
||
|
|
#define BTN_ENC 37 // EXP1.2
|
||
|
|
#define BTN_EN1 31 // EXP2.5
|
||
|
|
#define BTN_EN2 33 // EXP2.3
|
||
|
|
|
||
|
|
#define SD_DETECT_PIN 57 // EXP2.7
|
||
|
|
#define KILL_PIN -1 // Not connected
|
||
|
|
#define LCD_PINS_RS 16 // EXP1.4
|
||
|
|
#define LCD_SDSS 58 // EXP2.4
|
||
|
|
#define LCD_BACKLIGHT_PIN -1 // Not connected
|
||
|
|
#define LCD_PINS_ENABLE 51 // EXP1.3
|
||
|
|
#define LCD_PINS_D4 80 // EXP1.5
|
||
|
|
|
||
|
|
#define DOGLCD_A0 -1 // Not connected
|
||
|
|
#define DOGLCD_CS -1 // Not connected
|
||
|
|
|
||
|
|
#ifdef ULTIPANEL
|
||
|
|
|
||
|
|
#define LCD_PINS_D5 -1 // EXP1.6 Not connected
|
||
|
|
#define LCD_PINS_D6 -1 // EXP1.7 Not connected
|
||
|
|
#define LCD_PINS_D7 -1 // EXP1.8 Not connected
|
||
|
|
#endif
|
||
|
|
|
||
|
|
|
||
|
|
#if ENABLED(SDSUPPORT)
|
||
|
|
#define SDCARD_SORT_ALPHA // Using SORT feature to keep one directory level in RAM
|
||
|
|
// When going up/down directory levels the SD card is
|
||
|
|
// accessed but the garbage/lines are removed when the
|
||
|
|
// LCD updates
|
||
|
|
|
||
|
|
// SD Card Sorting options
|
||
|
|
#if ENABLED(SDCARD_SORT_ALPHA)
|
||
|
|
#define SDSORT_LIMIT 255 // Maximum number of sorted items (10-256).
|
||
|
|
#define FOLDER_SORTING -1 // -1=above 0=none 1=below
|
||
|
|
#define SDSORT_GCODE false // Allow turning sorting on/off with LCD and M34 g-code.
|
||
|
|
#define SDSORT_USES_RAM true // Pre-allocate a static array for faster pre-sorting.
|
||
|
|
#define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.)
|
||
|
|
#define SDSORT_CACHE_NAMES true // Keep sorted items in RAM longer for speedy performance. Most expensive option.
|
||
|
|
#define SDSORT_DYNAMIC_RAM false // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use!
|
||
|
|
#endif
|
||
|
|
#endif
|
||
|
|
#endif // ULTRA_LCD
|
||
|
|
|
||
|
|
//
|
||
|
|
// Ethernet pins
|
||
|
|
//
|
||
|
|
#ifndef ULTIPANEL
|
||
|
|
#define ENET_MDIO 71 // J12-4
|
||
|
|
#define ENET_RX_ER 73 // J12-6
|
||
|
|
#define ENET_RXD1 75 // J12-8
|
||
|
|
#endif
|
||
|
|
#define ENET_MOC 70 // J12-3
|
||
|
|
#define REF_CLK 72 // J12-5
|
||
|
|
#define ENET_RXD0 74 // J12-7
|
||
|
|
#define ENET_CRS 76 // J12-9
|
||
|
|
#define ENET_TX_EN 77 // J12-10
|
||
|
|
#define ENET_TXD0 78 // J12-11
|
||
|
|
#define ENET_TXD1 79 // J12-12
|
||
|
|
|
||
|
|
/**
|
||
|
|
* PWMS
|
||
|
|
*
|
||
|
|
* There are 6 PWMS. Each PWM can be assigned to one of two pins.
|
||
|
|
*
|
||
|
|
* SERVO2 does NOT have a PWM assigned to it.
|
||
|
|
*
|
||
|
|
* PWM1.1 DIO4 SERVO3_PIN FIL_RUNOUT_PIN 5V output, PWM
|
||
|
|
* PWM1.1 DIO26 E0_STEP_PIN
|
||
|
|
* PWM1.2 DIO11 SERVO0_PIN
|
||
|
|
* PWM1.2 DIO54 X_STEP_PIN
|
||
|
|
* PWM1.3 DIO6 SERVO1_PIN J5-1
|
||
|
|
* PWM1.3 DIO60 Y_STEP_PIN
|
||
|
|
* PWM1.4 DIO53 SDSS(SSEL0) J3-5 AUX-3
|
||
|
|
* PWM1.4 DIO46 Z_STEP_PIN
|
||
|
|
* PWM1.5 DIO3 X_MIN_PIN 10K PULLUP TO 3.3v, 1K SERIES
|
||
|
|
* PWM1.5 DIO9 RAMPS_D9_PIN
|
||
|
|
* PWM1.6 DIO14 Y_MIN_PIN 10K PULLUP TO 3.3v, 1K SERIES
|
||
|
|
* PWM1.6 DIO10 RAMPS_D10_PIN
|
||
|
|
*/
|
||
|
|
|
||
|
|
|
||
|
|
/**
|
||
|
|
* special pins
|
||
|
|
* D37 - not 5V tolerant
|
||
|
|
* D49 - not 5V tolerant
|
||
|
|
* D57 - open collector
|
||
|
|
* D58 - open collector
|
||
|
|
*
|
||
|
|
*/
|