muele-marlin/Marlin/pins_SETHI.h

/**
 * Marlin 3D Printer Firmware
 * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
 *
 * Based on Sprinter and grbl.
 * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 3 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */

/**
 * Sethi 3D_1 pin assignments - www.sethi3d.com.br
 */

#if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__) && !defined(__AVR_ATmega1284P__)
  #error "Oops!  Make sure you have 'Sethi 3D' selected from the 'Tools -> Boards' menu."
#endif

#define BOARD_NAME "Sethi 3D_1"

#ifndef GEN7_VERSION
  #define GEN7_VERSION 12 // v1.x
#endif

//
// Limit Switches
//
#define X_STOP_PIN          2
#define Y_STOP_PIN          0
#define Z_MIN_PIN           1
#define Z_MAX_PIN           0

//
// Steppers
//
#define X_STEP_PIN         19
#define X_DIR_PIN          18
#define X_ENABLE_PIN       24

#define Y_STEP_PIN         23
#define Y_DIR_PIN          22
#define Y_ENABLE_PIN       24

#define Z_STEP_PIN         26
#define Z_DIR_PIN          25
#define Z_ENABLE_PIN       24

#define E0_STEP_PIN        28
#define E0_DIR_PIN         27
#define E0_ENABLE_PIN      24

//
// Temperature Sensors
//
#define TEMP_0_PIN          1   // Analog Input
#define TEMP_BED_PIN        2   // Analog Input

//
// Heaters / Fans
//
#define HEATER_0_PIN        4
#define HEATER_BED_PIN      3


#if (GEN7_VERSION >= 13)
  // Gen7 v1.3 removed the fan pin
  #define FAN_PIN          -1
#else
  #define FAN_PIN          31
#endif

//
// Misc. Functions
//
#define PS_ON_PIN          15

// All these generations of Gen7 supply thermistor power
// via PS_ON, so ignore bad thermistor readings
#define BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE

// our pin for debugging.
#define DEBUG_PIN           0

// our RS485 pins
#define TX_ENABLE_PIN      12
#define RX_ENABLE_PIN      13
Further cleanup of comments, partial Doxygen-style Following up on #3231 2016-03-25 06:19:46 +00:00			`/**`
Added gplv3 header to all Marlin files 2016-03-24 18:01:20 +00:00			`* Marlin 3D Printer Firmware`
			`* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]`
			`*`
			`* Based on Sprinter and grbl.`
			`* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm`
			`*`
			`* This program is free software: you can redistribute it and/or modify`
			`* it under the terms of the GNU General Public License as published by`
			`* the Free Software Foundation, either version 3 of the License, or`
			`* (at your option) any later version.`
			`*`
			`* This program is distributed in the hope that it will be useful,`
			`* but WITHOUT ANY WARRANTY; without even the implied warranty of`
			`* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the`
			`* GNU General Public License for more details.`
			`*`
			`* You should have received a copy of the GNU General Public License`
			`* along with this program. If not, see <http://www.gnu.org/licenses/>.`
			`*`
			`*/`

Split up pins to make it more manageable Hopefully this is helpful to organization and future expansion…. 2015-01-26 02:40:00 +00:00			`/**`
			`* Sethi 3D_1 pin assignments - www.sethi3d.com.br`
			`*/`

			`#if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__) && !defined(__AVR_ATmega1284P__)`
Enclose all #error strings with apostrophes 2016-05-13 12:10:23 +00:00			`#error "Oops! Make sure you have 'Sethi 3D' selected from the 'Tools -> Boards' menu."`
Split up pins to make it more manageable Hopefully this is helpful to organization and future expansion…. 2015-01-26 02:40:00 +00:00			`#endif`

Add "About Printer" information menu. Includes: firmware version / branch / date. extruder count board information (name, serial details, power supply type) thermistors (names, min/max temperatures) *printer statistics (PRINTCOUNTER details) Thanks to @thinkyhead for contributions. 2016-06-30 09:24:29 +00:00			`#define BOARD_NAME "Sethi 3D_1"`

Split up pins to make it more manageable Hopefully this is helpful to organization and future expansion…. 2015-01-26 02:40:00 +00:00			`#ifndef GEN7_VERSION`
			`#define GEN7_VERSION 12 // v1.x`
			`#endif`

Consistent order/formatting of pins files 2016-08-22 22:05:22 +00:00			`//`
			`// Limit Switches`
			`//`
			`#define X_STOP_PIN 2`
			`#define Y_STOP_PIN 0`
			`#define Z_MIN_PIN 1`
			`#define Z_MAX_PIN 0`

			`//`
			`// Steppers`
			`//`
			`#define X_STEP_PIN 19`
			`#define X_DIR_PIN 18`
			`#define X_ENABLE_PIN 24`

			`#define Y_STEP_PIN 23`
			`#define Y_DIR_PIN 22`
			`#define Y_ENABLE_PIN 24`

			`#define Z_STEP_PIN 26`
			`#define Z_DIR_PIN 25`
			`#define Z_ENABLE_PIN 24`

			`#define E0_STEP_PIN 28`
			`#define E0_DIR_PIN 27`
			`#define E0_ENABLE_PIN 24`

			`//`
			`// Temperature Sensors`
			`//`
Follow-up the PR #4955, etc ・More ANALOG NUMBERING to Analog Input ・Add comment header to all the section of all the pins files ・Sort sections as follows: 1. Some special definitions (USBCON, LARGE_FLASH, etc) 2. Servos 3. Limit Switches 4. Z Probe 5. Steppers 6. Temperature Sensors 7. Heaters / Fans 8. Misc. Functions 9. LCD / Controller ・Move MAX6675_SS into "Temperature Sensors" section ・Adjust spacing 2016-10-08 20:27:04 +00:00			`#define TEMP_0_PIN 1 // Analog Input`
			`#define TEMP_BED_PIN 2 // Analog Input`
Consistent order/formatting of pins files 2016-08-22 22:05:22 +00:00
			`//`
			`// Heaters / Fans`
			`//`
			`#define HEATER_0_PIN 4`
			`#define HEATER_BED_PIN 3`
Split up pins to make it more manageable Hopefully this is helpful to organization and future expansion…. 2015-01-26 02:40:00 +00:00

			`#if (GEN7_VERSION >= 13)`
			`// Gen7 v1.3 removed the fan pin`
Consistent order/formatting of pins files 2016-08-22 22:05:22 +00:00			`#define FAN_PIN -1`
Split up pins to make it more manageable Hopefully this is helpful to organization and future expansion…. 2015-01-26 02:40:00 +00:00			`#else`
Consistent order/formatting of pins files 2016-08-22 22:05:22 +00:00			`#define FAN_PIN 31`
Split up pins to make it more manageable Hopefully this is helpful to organization and future expansion…. 2015-01-26 02:40:00 +00:00			`#endif`

Follow-up the PR #4955, etc ・More ANALOG NUMBERING to Analog Input ・Add comment header to all the section of all the pins files ・Sort sections as follows: 1. Some special definitions (USBCON, LARGE_FLASH, etc) 2. Servos 3. Limit Switches 4. Z Probe 5. Steppers 6. Temperature Sensors 7. Heaters / Fans 8. Misc. Functions 9. LCD / Controller ・Move MAX6675_SS into "Temperature Sensors" section ・Adjust spacing 2016-10-08 20:27:04 +00:00			`//`
			`// Misc. Functions`
			`//`
Consistent order/formatting of pins files 2016-08-22 22:05:22 +00:00			`#define PS_ON_PIN 15`
Split up pins to make it more manageable Hopefully this is helpful to organization and future expansion…. 2015-01-26 02:40:00 +00:00
Follow-up the PR #4955, etc ・More ANALOG NUMBERING to Analog Input ・Add comment header to all the section of all the pins files ・Sort sections as follows: 1. Some special definitions (USBCON, LARGE_FLASH, etc) 2. Servos 3. Limit Switches 4. Z Probe 5. Steppers 6. Temperature Sensors 7. Heaters / Fans 8. Misc. Functions 9. LCD / Controller ・Move MAX6675_SS into "Temperature Sensors" section ・Adjust spacing 2016-10-08 20:27:04 +00:00			`// All these generations of Gen7 supply thermistor power`
			`// via PS_ON, so ignore bad thermistor readings`
Split up pins to make it more manageable Hopefully this is helpful to organization and future expansion…. 2015-01-26 02:40:00 +00:00			`#define BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE`

Follow-up the PR #4955, etc ・More ANALOG NUMBERING to Analog Input ・Add comment header to all the section of all the pins files ・Sort sections as follows: 1. Some special definitions (USBCON, LARGE_FLASH, etc) 2. Servos 3. Limit Switches 4. Z Probe 5. Steppers 6. Temperature Sensors 7. Heaters / Fans 8. Misc. Functions 9. LCD / Controller ・Move MAX6675_SS into "Temperature Sensors" section ・Adjust spacing 2016-10-08 20:27:04 +00:00			`// our pin for debugging.`
Consistent order/formatting of pins files 2016-08-22 22:05:22 +00:00			`#define DEBUG_PIN 0`
Split up pins to make it more manageable Hopefully this is helpful to organization and future expansion…. 2015-01-26 02:40:00 +00:00
Follow-up the PR #4955, etc ・More ANALOG NUMBERING to Analog Input ・Add comment header to all the section of all the pins files ・Sort sections as follows: 1. Some special definitions (USBCON, LARGE_FLASH, etc) 2. Servos 3. Limit Switches 4. Z Probe 5. Steppers 6. Temperature Sensors 7. Heaters / Fans 8. Misc. Functions 9. LCD / Controller ・Move MAX6675_SS into "Temperature Sensors" section ・Adjust spacing 2016-10-08 20:27:04 +00:00			`// our RS485 pins`
Consistent order/formatting of pins files 2016-08-22 22:05:22 +00:00			`#define TX_ENABLE_PIN 12`
			`#define RX_ENABLE_PIN 13`