muele-marlin/Marlin/pins_GEN6.h

/**
 * Marlin 3D Printer Firmware
 * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
 *
 * Based on Sprinter and grbl.
 * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 3 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */

/**
 * Gen6 pin assignments
 */

#ifndef __AVR_ATmega644P__
  #ifndef __AVR_ATmega1284P__
    #error "Oops!  Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu."
  #endif
#endif

#ifndef BOARD_NAME
  #define BOARD_NAME "Gen6"
#endif

//
// Limit Switches
//
#define X_STOP_PIN         20
#define Y_STOP_PIN         25
#define Z_STOP_PIN         30

//
// Steppers
//
#define X_STEP_PIN         15
#define X_DIR_PIN          18
#define X_ENABLE_PIN       19

#define Y_STEP_PIN         23
#define Y_DIR_PIN          22
#define Y_ENABLE_PIN       24

#define Z_STEP_PIN         27
#define Z_DIR_PIN          28
#define Z_ENABLE_PIN       29

#define E0_STEP_PIN         4   // Edited @ EJE Electronics 20100715
#define E0_DIR_PIN          2   // Edited @ EJE Electronics 20100715
#define E0_ENABLE_PIN       3   // Added @ EJE Electronics 20100715

//
// Temperature Sensor
//
#define TEMP_0_PIN          5   // Analog Input

//
// Heaters
//
#define HEATER_0_PIN       14   // changed @ rkoeppl 20110410

#if !MB(GEN6)
  #define HEATER_BED_PIN    1   // changed @ rkoeppl 20110410
  #define TEMP_BED_PIN      0   // Analog Input
#endif

//
// Misc. Functions
//
#define SDSS               17
#define DEBUG_PIN           0

// RS485 pins
#define TX_ENABLE_PIN      12
#define RX_ENABLE_PIN      13
Further cleanup of comments, partial Doxygen-style Following up on #3231 2016-03-25 06:19:46 +00:00			`/**`
Added gplv3 header to all Marlin files 2016-03-24 18:01:20 +00:00			`* Marlin 3D Printer Firmware`
			`* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]`
			`*`
			`* Based on Sprinter and grbl.`
			`* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm`
			`*`
			`* This program is free software: you can redistribute it and/or modify`
			`* it under the terms of the GNU General Public License as published by`
			`* the Free Software Foundation, either version 3 of the License, or`
			`* (at your option) any later version.`
			`*`
			`* This program is distributed in the hope that it will be useful,`
			`* but WITHOUT ANY WARRANTY; without even the implied warranty of`
			`* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the`
			`* GNU General Public License for more details.`
			`*`
			`* You should have received a copy of the GNU General Public License`
			`* along with this program. If not, see <http://www.gnu.org/licenses/>.`
			`*`
			`*/`

Split up pins to make it more manageable Hopefully this is helpful to organization and future expansion…. 2015-01-26 02:40:00 +00:00			`/**`
			`* Gen6 pin assignments`
			`*/`

			`#ifndef __AVR_ATmega644P__`
			`#ifndef __AVR_ATmega1284P__`
Enclose all #error strings with apostrophes 2016-05-13 12:10:23 +00:00			`#error "Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu."`
Split up pins to make it more manageable Hopefully this is helpful to organization and future expansion…. 2015-01-26 02:40:00 +00:00			`#endif`
			`#endif`

Add "About Printer" information menu. Includes: firmware version / branch / date. extruder count board information (name, serial details, power supply type) thermistors (names, min/max temperatures) *printer statistics (PRINTCOUNTER details) Thanks to @thinkyhead for contributions. 2016-06-30 09:24:29 +00:00			`#ifndef BOARD_NAME`
			`#define BOARD_NAME "Gen6"`
			`#endif`

Consistent order/formatting of pins files 2016-08-22 22:05:22 +00:00			`//`
			`// Limit Switches`
			`//`
			`#define X_STOP_PIN 20`
			`#define Y_STOP_PIN 25`
			`#define Z_STOP_PIN 30`
Split up pins to make it more manageable Hopefully this is helpful to organization and future expansion…. 2015-01-26 02:40:00 +00:00
Consistent order/formatting of pins files 2016-08-22 22:05:22 +00:00			`//`
			`// Steppers`
			`//`
			`#define X_STEP_PIN 15`
			`#define X_DIR_PIN 18`
			`#define X_ENABLE_PIN 19`
Split up pins to make it more manageable Hopefully this is helpful to organization and future expansion…. 2015-01-26 02:40:00 +00:00
Consistent order/formatting of pins files 2016-08-22 22:05:22 +00:00			`#define Y_STEP_PIN 23`
			`#define Y_DIR_PIN 22`
			`#define Y_ENABLE_PIN 24`
Split up pins to make it more manageable Hopefully this is helpful to organization and future expansion…. 2015-01-26 02:40:00 +00:00
Consistent order/formatting of pins files 2016-08-22 22:05:22 +00:00			`#define Z_STEP_PIN 27`
			`#define Z_DIR_PIN 28`
			`#define Z_ENABLE_PIN 29`
Split up pins to make it more manageable Hopefully this is helpful to organization and future expansion…. 2015-01-26 02:40:00 +00:00
Follow-up the PR #4955, etc ・More ANALOG NUMBERING to Analog Input ・Add comment header to all the section of all the pins files ・Sort sections as follows: 1. Some special definitions (USBCON, LARGE_FLASH, etc) 2. Servos 3. Limit Switches 4. Z Probe 5. Steppers 6. Temperature Sensors 7. Heaters / Fans 8. Misc. Functions 9. LCD / Controller ・Move MAX6675_SS into "Temperature Sensors" section ・Adjust spacing 2016-10-08 20:27:04 +00:00			`#define E0_STEP_PIN 4 // Edited @ EJE Electronics 20100715`
			`#define E0_DIR_PIN 2 // Edited @ EJE Electronics 20100715`
			`#define E0_ENABLE_PIN 3 // Added @ EJE Electronics 20100715`
Consistent order/formatting of pins files 2016-08-22 22:05:22 +00:00
			`//`
			`// Temperature Sensor`
			`//`
Label analog pins in a similar way Some other pins formatting also 2016-10-05 06:52:43 +00:00			`#define TEMP_0_PIN 5 // Analog Input`
Consistent order/formatting of pins files 2016-08-22 22:05:22 +00:00
			`//`
			`// Heaters`
			`//`
Follow-up the PR #4955, etc ・More ANALOG NUMBERING to Analog Input ・Add comment header to all the section of all the pins files ・Sort sections as follows: 1. Some special definitions (USBCON, LARGE_FLASH, etc) 2. Servos 3. Limit Switches 4. Z Probe 5. Steppers 6. Temperature Sensors 7. Heaters / Fans 8. Misc. Functions 9. LCD / Controller ・Move MAX6675_SS into "Temperature Sensors" section ・Adjust spacing 2016-10-08 20:27:04 +00:00			`#define HEATER_0_PIN 14 // changed @ rkoeppl 20110410`
Split up pins to make it more manageable Hopefully this is helpful to organization and future expansion…. 2015-01-26 02:40:00 +00:00
Cleanup pins files, fixup analogtodigitalpin, etc. 2016-05-08 01:41:20 +00:00			`#if !MB(GEN6)`
Follow-up the PR #4955, etc ・More ANALOG NUMBERING to Analog Input ・Add comment header to all the section of all the pins files ・Sort sections as follows: 1. Some special definitions (USBCON, LARGE_FLASH, etc) 2. Servos 3. Limit Switches 4. Z Probe 5. Steppers 6. Temperature Sensors 7. Heaters / Fans 8. Misc. Functions 9. LCD / Controller ・Move MAX6675_SS into "Temperature Sensors" section ・Adjust spacing 2016-10-08 20:27:04 +00:00			`#define HEATER_BED_PIN 1 // changed @ rkoeppl 20110410`
Label analog pins in a similar way Some other pins formatting also 2016-10-05 06:52:43 +00:00			`#define TEMP_BED_PIN 0 // Analog Input`
Split up pins to make it more manageable Hopefully this is helpful to organization and future expansion…. 2015-01-26 02:40:00 +00:00			`#endif`

Consistent order/formatting of pins files 2016-08-22 22:05:22 +00:00			`//`
			`// Misc. Functions`
			`//`
Follow-up the PR #4955, etc ・More ANALOG NUMBERING to Analog Input ・Add comment header to all the section of all the pins files ・Sort sections as follows: 1. Some special definitions (USBCON, LARGE_FLASH, etc) 2. Servos 3. Limit Switches 4. Z Probe 5. Steppers 6. Temperature Sensors 7. Heaters / Fans 8. Misc. Functions 9. LCD / Controller ・Move MAX6675_SS into "Temperature Sensors" section ・Adjust spacing 2016-10-08 20:27:04 +00:00			`#define SDSS 17`
Consistent order/formatting of pins files 2016-08-22 22:05:22 +00:00			`#define DEBUG_PIN 0`
Split up pins to make it more manageable Hopefully this is helpful to organization and future expansion…. 2015-01-26 02:40:00 +00:00
Consistent order/formatting of pins files 2016-08-22 22:05:22 +00:00			`// RS485 pins`
			`#define TX_ENABLE_PIN 12`
			`#define RX_ENABLE_PIN 13`