2019-07-09 05:30:08 +00:00
|
|
|
/**
|
|
|
|
|
* Marlin 3D Printer Firmware
|
|
|
|
|
* Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|
|
|
|
*
|
|
|
|
|
* Based on Sprinter and grbl.
|
|
|
|
|
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
|
|
|
|
|
*
|
|
|
|
|
* This program is free software: you can redistribute it and/or modify
|
|
|
|
|
* it under the terms of the GNU General Public License as published by
|
|
|
|
|
* the Free Software Foundation, either version 3 of the License, or
|
|
|
|
|
* (at your option) any later version.
|
|
|
|
|
*
|
|
|
|
|
* This program is distributed in the hope that it will be useful,
|
|
|
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
|
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
|
|
|
* GNU General Public License for more details.
|
|
|
|
|
*
|
|
|
|
|
* You should have received a copy of the GNU General Public License
|
|
|
|
|
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
|
|
|
*
|
|
|
|
|
*/
|
|
|
|
|
#pragma once
|
|
|
|
|
|
2019-11-03 02:34:09 +00:00
|
|
|
#ifndef MCU_LPC1768
|
2019-07-09 05:30:08 +00:00
|
|
|
#error "Oops! Make sure you have the LPC1768 environment selected in your IDE."
|
|
|
|
|
#endif
|
|
|
|
|
|
2019-08-21 00:08:58 +00:00
|
|
|
#define BOARD_INFO_NAME "GMARSH X6 REV1"
|
2019-07-09 05:30:08 +00:00
|
|
|
|
|
|
|
|
// Ignore temp readings during develpment.
|
2019-09-16 21:50:57 +00:00
|
|
|
//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000
|
2019-07-09 05:30:08 +00:00
|
|
|
|
|
|
|
|
//
|
|
|
|
|
// Enable 12MHz clock output on P1.27 pin to sync TMC2208 chip clocks
|
|
|
|
|
//
|
|
|
|
|
#define LPC1768_ENABLE_CLKOUT_12M
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
|
// Servos
|
|
|
|
|
//
|
|
|
|
|
#define SERVO0_PIN P1_26 // PWM1[6]
|
|
|
|
|
#define SERVO1_PIN P1_18 // PWM1[1]
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
|
// Limit Switches
|
|
|
|
|
//
|
|
|
|
|
#define X_MIN_PIN P0_00
|
|
|
|
|
#define X_MAX_PIN P0_01
|
|
|
|
|
#define Y_MIN_PIN P0_10
|
|
|
|
|
#define Y_MAX_PIN P0_21
|
|
|
|
|
#define Z_MIN_PIN P2_13
|
|
|
|
|
#define Z_MAX_PIN P2_22
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
|
// Steppers
|
|
|
|
|
//
|
|
|
|
|
|
|
|
|
|
#define X_STEP_PIN P1_01
|
|
|
|
|
#define X_DIR_PIN P1_04
|
|
|
|
|
#define X_ENABLE_PIN P0_26
|
|
|
|
|
|
|
|
|
|
#define Y_STEP_PIN P1_10
|
|
|
|
|
#define Y_DIR_PIN P1_14
|
|
|
|
|
#define Y_ENABLE_PIN P1_08
|
|
|
|
|
|
|
|
|
|
#define Z_STEP_PIN P1_17
|
|
|
|
|
#define Z_DIR_PIN P4_29
|
|
|
|
|
#define Z_ENABLE_PIN P1_15
|
|
|
|
|
|
|
|
|
|
#define E0_STEP_PIN P0_05
|
|
|
|
|
#define E0_DIR_PIN P2_00
|
|
|
|
|
#define E0_ENABLE_PIN P4_28
|
|
|
|
|
|
|
|
|
|
#define E1_STEP_PIN P2_03
|
|
|
|
|
#define E1_DIR_PIN P2_04
|
|
|
|
|
#define E1_ENABLE_PIN P2_01
|
|
|
|
|
|
|
|
|
|
#define E2_STEP_PIN P2_07
|
|
|
|
|
#define E2_DIR_PIN P2_08
|
|
|
|
|
#define E2_ENABLE_PIN P2_05
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
|
// TMC2208 UART pins
|
|
|
|
|
//
|
|
|
|
|
#if HAS_DRIVER(TMC2208)
|
|
|
|
|
#define X_SERIAL_TX_PIN P1_00
|
|
|
|
|
#define X_SERIAL_RX_PIN P1_00
|
|
|
|
|
#define Y_SERIAL_TX_PIN P1_09
|
|
|
|
|
#define Y_SERIAL_RX_PIN P1_09
|
|
|
|
|
#define Z_SERIAL_TX_PIN P1_16
|
|
|
|
|
#define Z_SERIAL_RX_PIN P1_16
|
|
|
|
|
#define E0_SERIAL_TX_PIN P0_04
|
|
|
|
|
#define E0_SERIAL_RX_PIN P0_04
|
|
|
|
|
#define E1_SERIAL_TX_PIN P2_02
|
|
|
|
|
#define E1_SERIAL_RX_PIN P2_02
|
|
|
|
|
#define E2_SERIAL_TX_PIN P2_06
|
|
|
|
|
#define E2_SERIAL_RX_PIN P2_06
|
2019-11-06 23:08:12 +00:00
|
|
|
|
|
|
|
|
// Reduce baud rate to improve software serial reliability
|
|
|
|
|
#define TMC_BAUD_RATE 19200
|
2019-07-09 05:30:08 +00:00
|
|
|
#else
|
|
|
|
|
#error "TMC2208 UART configuration is required for GMarsh X6."
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
|
// Temperature Sensors
|
|
|
|
|
// 3.3V max when defined as an analog input
|
|
|
|
|
//
|
2019-11-03 02:34:09 +00:00
|
|
|
#define TEMP_0_PIN P0_24_A1 // AD0[0] on P0_23
|
|
|
|
|
#define TEMP_BED_PIN P0_23_A0 // AD0[1] on P0_24
|
2019-07-09 05:30:08 +00:00
|
|
|
|
|
|
|
|
//
|
|
|
|
|
// Heaters / Fans
|
|
|
|
|
//
|
|
|
|
|
#define HEATER_BED_PIN P1_19 // Not a PWM pin, software PWM required
|
|
|
|
|
#define HEATER_0_PIN P3_26 // PWM1[3]
|
|
|
|
|
#define FAN_PIN P3_25 // Part cooling fan - connected to PWM1[2]
|
|
|
|
|
#define E0_AUTO_FAN_PIN P0_27 // Extruder cooling fan
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
|
// Misc. Functions
|
|
|
|
|
//
|
|
|
|
|
#define LED_PIN P1_31
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
|
// LCD
|
|
|
|
|
//
|
|
|
|
|
#if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER)
|
|
|
|
|
#define BEEPER_PIN P0_19
|
|
|
|
|
#define BTN_EN1 P1_23
|
|
|
|
|
#define BTN_EN2 P1_24
|
|
|
|
|
#define BTN_ENC P1_25
|
|
|
|
|
#define LCD_PINS_RS P0_20
|
|
|
|
|
#define LCD_PINS_ENABLE P0_21
|
|
|
|
|
#define LCD_PINS_D4 P2_11
|
|
|
|
|
#define LCD_PINS_D5 P0_22
|
|
|
|
|
#define LCD_PINS_D6 P1_29
|
|
|
|
|
#define LCD_PINS_D7 P1_28
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
|
// SD Support
|
|
|
|
|
//
|
|
|
|
|
|
|
|
|
|
#ifndef SDCARD_CONNECTION
|
|
|
|
|
#define SDCARD_CONNECTION LCD
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
#define ONBOARD_SD_CS_PIN P0_06 // Chip select for "System" SD card
|
|
|
|
|
|
|
|
|
|
#if SD_CONNECTION_IS(LCD)
|
|
|
|
|
#define SCK_PIN P0_15
|
|
|
|
|
#define MISO_PIN P0_17
|
|
|
|
|
#define MOSI_PIN P0_18
|
|
|
|
|
#define SS_PIN P0_16
|
|
|
|
|
#elif SD_CONNECTION_IS(ONBOARD)
|
|
|
|
|
#undef SD_DETECT_PIN
|
|
|
|
|
#define SD_DETECT_PIN P0_27
|
|
|
|
|
#define SCK_PIN P0_07
|
|
|
|
|
#define MISO_PIN P0_08
|
|
|
|
|
#define MOSI_PIN P0_09
|
|
|
|
|
#define SS_PIN ONBOARD_SD_CS_PIN
|
|
|
|
|
#endif
|
