2020-06-21 08:46:31 +00:00
|
|
|
/**
|
|
|
|
|
* Marlin 3D Printer Firmware
|
|
|
|
|
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|
|
|
|
*
|
|
|
|
|
* Based on Sprinter and grbl.
|
|
|
|
|
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
|
|
|
|
|
*
|
|
|
|
|
* This program is free software: you can redistribute it and/or modify
|
|
|
|
|
* it under the terms of the GNU General Public License as published by
|
|
|
|
|
* the Free Software Foundation, either version 3 of the License, or
|
|
|
|
|
* (at your option) any later version.
|
|
|
|
|
*
|
|
|
|
|
* This program is distributed in the hope that it will be useful,
|
|
|
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
|
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
|
|
|
* GNU General Public License for more details.
|
|
|
|
|
*
|
|
|
|
|
* You should have received a copy of the GNU General Public License
|
2020-07-23 03:20:14 +00:00
|
|
|
* along with this program. If not, see <https://www.gnu.org/licenses/>.
|
2020-06-21 08:46:31 +00:00
|
|
|
*
|
|
|
|
|
*/
|
|
|
|
|
#pragma once
|
|
|
|
|
|
|
|
|
|
#ifndef TARGET_STM32F4
|
|
|
|
|
#error "Oops! Select an STM32F4 board in 'Tools > Board.'"
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
// Use one of these or SDCard-based Emulation will be used
|
|
|
|
|
#if NO_EEPROM_SELECTED
|
|
|
|
|
//#define SRAM_EEPROM_EMULATION // Use BackSRAM-based EEPROM emulation
|
|
|
|
|
#define FLASH_EEPROM_EMULATION // Use Flash-based EEPROM emulation
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
#if ENABLED(FLASH_EEPROM_EMULATION)
|
|
|
|
|
// Decrease delays and flash wear by spreading writes across the
|
|
|
|
|
// 128 kB sector allocated for EEPROM emulation.
|
|
|
|
|
#define FLASH_EEPROM_LEVELING
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
|
// Servos
|
|
|
|
|
//
|
|
|
|
|
#define SERVO0_PIN PA1
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
|
// Trinamic Stallguard pins
|
|
|
|
|
//
|
|
|
|
|
#define X_DIAG_PIN PB10 // X-
|
|
|
|
|
#define Y_DIAG_PIN PE12 // Y-
|
|
|
|
|
#define Z_DIAG_PIN PG8 // Z-
|
|
|
|
|
#define E0_DIAG_PIN PE15 // E0
|
|
|
|
|
#define E1_DIAG_PIN PE10 // E1
|
|
|
|
|
#define E2_DIAG_PIN PG5 // E2
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
|
// Limit Switches
|
|
|
|
|
//
|
|
|
|
|
#ifdef X_STALL_SENSITIVITY
|
|
|
|
|
#define X_STOP_PIN X_DIAG_PIN
|
|
|
|
|
#if X_HOME_DIR < 0
|
|
|
|
|
#define X_MAX_PIN PE15 // E0
|
|
|
|
|
#else
|
|
|
|
|
#define X_MIN_PIN PE15 // E0
|
|
|
|
|
#endif
|
|
|
|
|
#else
|
|
|
|
|
#define X_MIN_PIN PB10 // X-
|
|
|
|
|
#define X_MAX_PIN PE15 // E0
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
#ifdef Y_STALL_SENSITIVITY
|
|
|
|
|
#define Y_STOP_PIN Y_DIAG_PIN
|
|
|
|
|
#if Y_HOME_DIR < 0
|
|
|
|
|
#define Y_MAX_PIN PE10 // E1
|
|
|
|
|
#else
|
|
|
|
|
#define Y_MIN_PIN PE10 // E1
|
|
|
|
|
#endif
|
|
|
|
|
#else
|
|
|
|
|
#define Y_MIN_PIN PE12 // Y-
|
|
|
|
|
#define Y_MAX_PIN PE10 // E1
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
#ifdef Z_STALL_SENSITIVITY
|
|
|
|
|
#define Z_STOP_PIN Z_DIAG_PIN
|
|
|
|
|
#if Z_HOME_DIR < 0
|
|
|
|
|
#define Z_MAX_PIN PG5 // E2
|
|
|
|
|
#else
|
|
|
|
|
#define Z_MIN_PIN PG5 // E2
|
|
|
|
|
#endif
|
|
|
|
|
#else
|
|
|
|
|
#define Z_MIN_PIN PG8 // Z-
|
|
|
|
|
#define Z_MAX_PIN PG5 // E2
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
|
// Z Probe must be this pin
|
|
|
|
|
//
|
|
|
|
|
#ifndef Z_MIN_PROBE_PIN
|
|
|
|
|
#define Z_MIN_PROBE_PIN PA2
|
|
|
|
|
#endif
|
|
|
|
|
|
2020-06-26 06:46:31 +00:00
|
|
|
//
|
|
|
|
|
// Filament Runout Sensor
|
|
|
|
|
//
|
|
|
|
|
#ifndef FIL_RUNOUT_PIN
|
|
|
|
|
#define FIL_RUNOUT_PIN PE15
|
|
|
|
|
#endif
|
|
|
|
|
#ifndef FIL_RUNOUT2_PIN
|
|
|
|
|
#define FIL_RUNOUT2_PIN PE10
|
|
|
|
|
#endif
|
|
|
|
|
#ifndef FIL_RUNOUT3_PIN
|
|
|
|
|
#define FIL_RUNOUT3_PIN PG5
|
|
|
|
|
#endif
|
|
|
|
|
|
2020-06-21 08:46:31 +00:00
|
|
|
//
|
|
|
|
|
// Steppers
|
|
|
|
|
//
|
|
|
|
|
#define X_STEP_PIN PE9
|
|
|
|
|
#define X_DIR_PIN PF1
|
|
|
|
|
#define X_ENABLE_PIN PF2
|
|
|
|
|
#ifndef X_CS_PIN
|
|
|
|
|
#define X_CS_PIN PA15
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
#define Y_STEP_PIN PE11
|
|
|
|
|
#define Y_DIR_PIN PE8
|
|
|
|
|
#define Y_ENABLE_PIN PD7
|
|
|
|
|
#ifndef Y_CS_PIN
|
|
|
|
|
#define Y_CS_PIN PB8
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
#define Z_STEP_PIN PE13
|
|
|
|
|
#define Z_DIR_PIN PC2
|
|
|
|
|
#define Z_ENABLE_PIN PC0
|
|
|
|
|
#ifndef Z_CS_PIN
|
|
|
|
|
#define Z_CS_PIN PB9
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
#define E0_STEP_PIN PE14
|
|
|
|
|
#define E0_DIR_PIN PA0
|
|
|
|
|
#define E0_ENABLE_PIN PC3
|
|
|
|
|
#ifndef E0_CS_PIN
|
|
|
|
|
#define E0_CS_PIN PB3
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
#define E1_STEP_PIN PD15
|
|
|
|
|
#define E1_DIR_PIN PE7
|
|
|
|
|
#define E1_ENABLE_PIN PA3
|
|
|
|
|
#ifndef E1_CS_PIN
|
|
|
|
|
#define E1_CS_PIN PG15
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
#define E2_STEP_PIN PD13
|
|
|
|
|
#define E2_DIR_PIN PG9
|
|
|
|
|
#define E2_ENABLE_PIN PF0
|
|
|
|
|
#ifndef E2_CS_PIN
|
|
|
|
|
#define E2_CS_PIN PG12
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
|
// Software SPI pins for TMC2130 stepper drivers
|
|
|
|
|
//
|
|
|
|
|
#if ENABLED(TMC_USE_SW_SPI)
|
|
|
|
|
#ifndef TMC_SW_MOSI
|
|
|
|
|
#define TMC_SW_MOSI PC12
|
|
|
|
|
#endif
|
|
|
|
|
#ifndef TMC_SW_MISO
|
|
|
|
|
#define TMC_SW_MISO PC11
|
|
|
|
|
#endif
|
|
|
|
|
#ifndef TMC_SW_SCK
|
|
|
|
|
#define TMC_SW_SCK PC10
|
|
|
|
|
#endif
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
#if HAS_TMC_UART
|
|
|
|
|
/**
|
|
|
|
|
* TMC2208/TMC2209 stepper drivers
|
|
|
|
|
*
|
|
|
|
|
* Hardware serial communication ports.
|
|
|
|
|
* If undefined software serial is used according to the pins below
|
|
|
|
|
*/
|
|
|
|
|
//#define X_HARDWARE_SERIAL Serial
|
|
|
|
|
//#define X2_HARDWARE_SERIAL Serial1
|
|
|
|
|
//#define Y_HARDWARE_SERIAL Serial1
|
|
|
|
|
//#define Y2_HARDWARE_SERIAL Serial1
|
|
|
|
|
//#define Z_HARDWARE_SERIAL Serial1
|
|
|
|
|
//#define Z2_HARDWARE_SERIAL Serial1
|
|
|
|
|
//#define E0_HARDWARE_SERIAL Serial1
|
|
|
|
|
//#define E1_HARDWARE_SERIAL Serial1
|
|
|
|
|
//#define E2_HARDWARE_SERIAL Serial1
|
|
|
|
|
//#define E3_HARDWARE_SERIAL Serial1
|
|
|
|
|
//#define E4_HARDWARE_SERIAL Serial1
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
|
// Software serial
|
|
|
|
|
//
|
|
|
|
|
#define X_SERIAL_TX_PIN PC13
|
|
|
|
|
#define X_SERIAL_RX_PIN PC13
|
|
|
|
|
|
|
|
|
|
#define Y_SERIAL_TX_PIN PE3
|
|
|
|
|
#define Y_SERIAL_RX_PIN PE3
|
|
|
|
|
|
|
|
|
|
#define Z_SERIAL_TX_PIN PE1
|
|
|
|
|
#define Z_SERIAL_RX_PIN PE1
|
|
|
|
|
|
|
|
|
|
#define E0_SERIAL_TX_PIN PD4
|
|
|
|
|
#define E0_SERIAL_RX_PIN PD4
|
|
|
|
|
|
|
|
|
|
#define E1_SERIAL_TX_PIN PD1
|
|
|
|
|
#define E1_SERIAL_RX_PIN PD1
|
|
|
|
|
|
|
|
|
|
#define E2_SERIAL_TX_PIN PD6
|
|
|
|
|
#define E2_SERIAL_RX_PIN PD6
|
|
|
|
|
|
|
|
|
|
// Reduce baud rate to improve software serial reliability
|
2020-08-22 06:22:14 +00:00
|
|
|
#define TMC_BAUD_RATE 19200
|
2020-06-21 08:46:31 +00:00
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
|
// Temperature Sensors
|
|
|
|
|
//
|
|
|
|
|
#define TEMP_0_PIN PF4 // T1 <-> E0
|
|
|
|
|
#define TEMP_1_PIN PF5 // T2 <-> E1
|
|
|
|
|
#define TEMP_2_PIN PF6 // T3 <-> E2
|
|
|
|
|
#define TEMP_BED_PIN PF3 // T0 <-> Bed
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
|
// Heaters / Fans
|
|
|
|
|
//
|
|
|
|
|
#define HEATER_0_PIN PB1 // Heater0
|
|
|
|
|
#define HEATER_1_PIN PD14 // Heater1
|
|
|
|
|
#define HEATER_2_PIN PB0 // Heater1
|
|
|
|
|
#define HEATER_BED_PIN PD12 // Hotbed
|
|
|
|
|
#define FAN_PIN PC8 // Fan0
|
|
|
|
|
#define FAN1_PIN PE5 // Fan1
|
|
|
|
|
#define FAN2_PIN PE6
|
|
|
|
|
|
|
|
|
|
#ifndef E0_AUTO_FAN_PIN
|
|
|
|
|
#define E0_AUTO_FAN_PIN FAN1_PIN
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
|
// Misc. Functions
|
|
|
|
|
//
|
|
|
|
|
|
|
|
|
|
#ifndef SDCARD_CONNECTION
|
|
|
|
|
#define SDCARD_CONNECTION LCD
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
|
// Onboard SD card
|
|
|
|
|
// Must use soft SPI because Marlin's default hardware SPI is tied to LCD's EXP2
|
|
|
|
|
//
|
|
|
|
|
#if SD_CONNECTION_IS(ONBOARD)
|
|
|
|
|
#define SOFTWARE_SPI // Use soft SPI for onboard SD
|
|
|
|
|
#define SDSS PA4
|
|
|
|
|
#define SCK_PIN PA5
|
|
|
|
|
#define MISO_PIN PA6
|
|
|
|
|
#define MOSI_PIN PB5
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
/**
|
|
|
|
|
* _____ _____
|
|
|
|
|
* NC | · · | GND 5V | · · | GND
|
|
|
|
|
* RESET | · · | PF12(SD_DETECT) (LCD_D7) PG7 | · · | PG6 (LCD_D6)
|
|
|
|
|
* (MOSI)PB15 | · · | PF11(BTN_EN2) (LCD_D5) PG3 | · · | PG2 (LCD_D4)
|
|
|
|
|
* (SD_SS)PB12 | · · | PG10(BTN_EN1) (LCD_RS) PD10 | · · | PD11 (LCD_EN)
|
|
|
|
|
* (SCK)PB13 | · · | PB14(MISO) (BTN_ENC) PA8 | · · | PG4 (BEEPER)
|
|
|
|
|
* ￣￣ ￣￣
|
|
|
|
|
* EXP2 EXP1
|
|
|
|
|
*/
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
|
// LCDs and Controllers
|
|
|
|
|
//
|
|
|
|
|
#if HAS_SPI_LCD
|
|
|
|
|
#define BEEPER_PIN PG4
|
|
|
|
|
#define BTN_ENC PA8
|
|
|
|
|
#if SD_CONNECTION_IS(LCD)
|
|
|
|
|
#define SDSS PB12 // Uses default hardware SPI for LCD's SD
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
#if ENABLED(CR10_STOCKDISPLAY)
|
|
|
|
|
#define LCD_PINS_RS PG6
|
|
|
|
|
|
|
|
|
|
#define BTN_EN1 PD11
|
|
|
|
|
#define BTN_EN2 PG2
|
|
|
|
|
|
|
|
|
|
#define LCD_PINS_ENABLE PG7
|
|
|
|
|
#define LCD_PINS_D4 PG3
|
|
|
|
|
|
2020-06-22 20:27:01 +00:00
|
|
|
// CR10_STOCKDISPLAY default timing is too fast
|
|
|
|
|
#undef BOARD_ST7920_DELAY_1
|
|
|
|
|
#undef BOARD_ST7920_DELAY_2
|
|
|
|
|
#undef BOARD_ST7920_DELAY_3
|
2020-06-21 08:46:31 +00:00
|
|
|
|
|
|
|
|
#elif ENABLED(MKS_MINI_12864)
|
|
|
|
|
#define DOGLCD_A0 PG6
|
|
|
|
|
#define DOGLCD_CS PG3
|
|
|
|
|
|
|
|
|
|
#else
|
|
|
|
|
|
|
|
|
|
#define LCD_PINS_RS PD10
|
|
|
|
|
|
|
|
|
|
#define BTN_EN1 PG10
|
|
|
|
|
#define BTN_EN2 PF11
|
|
|
|
|
#define SD_DETECT_PIN PF12
|
|
|
|
|
|
|
|
|
|
#define LCD_SDSS PB12
|
|
|
|
|
|
|
|
|
|
#define LCD_PINS_ENABLE PD11
|
|
|
|
|
#define LCD_PINS_D4 PG2
|
|
|
|
|
|
|
|
|
|
#if ENABLED(FYSETC_MINI_12864)
|
|
|
|
|
#define DOGLCD_CS PD11
|
|
|
|
|
#define DOGLCD_A0 PD10
|
|
|
|
|
//#define LCD_BACKLIGHT_PIN -1
|
|
|
|
|
#define LCD_RESET_PIN PG2 // Must be high or open for LCD to operate normally.
|
|
|
|
|
#if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0)
|
|
|
|
|
#ifndef RGB_LED_R_PIN
|
|
|
|
|
#define RGB_LED_R_PIN PG3
|
|
|
|
|
#endif
|
|
|
|
|
#ifndef RGB_LED_G_PIN
|
|
|
|
|
#define RGB_LED_G_PIN PG6
|
|
|
|
|
#endif
|
|
|
|
|
#ifndef RGB_LED_B_PIN
|
|
|
|
|
#define RGB_LED_B_PIN PG7
|
|
|
|
|
#endif
|
|
|
|
|
#elif ENABLED(FYSETC_MINI_12864_2_1)
|
|
|
|
|
#define NEOPIXEL_PIN PG3
|
|
|
|
|
#endif
|
|
|
|
|
#endif // !FYSETC_MINI_12864
|
|
|
|
|
|
|
|
|
|
#if ENABLED(ULTIPANEL)
|
|
|
|
|
#define LCD_PINS_D5 PG3
|
|
|
|
|
#define LCD_PINS_D6 PG6
|
|
|
|
|
#define LCD_PINS_D7 PG7
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
// Alter timing for graphical display
|
|
|
|
|
#if HAS_GRAPHICAL_LCD
|
2020-06-22 20:27:01 +00:00
|
|
|
#ifndef BOARD_ST7920_DELAY_1
|
|
|
|
|
#define BOARD_ST7920_DELAY_1 DELAY_NS(96)
|
|
|
|
|
#endif
|
|
|
|
|
#ifndef BOARD_ST7920_DELAY_2
|
|
|
|
|
#define BOARD_ST7920_DELAY_2 DELAY_NS(48)
|
|
|
|
|
#endif
|
|
|
|
|
#ifndef BOARD_ST7920_DELAY_3
|
|
|
|
|
#define BOARD_ST7920_DELAY_3 DELAY_NS(600)
|
|
|
|
|
#endif
|
2020-06-21 08:46:31 +00:00
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
#endif // HAS_SPI_LCD
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
|
// WIFI
|
|
|
|
|
//
|
|
|
|
|
|
|
|
|
|
/**
|
|
|
|
|
* _____
|
|
|
|
|
* TX | 1 2 | GND Enable PG1 // Must be high for module to run
|
|
|
|
|
* Enable | 3 4 | GPIO2 Reset PG0 // active low, probably OK to leave floating
|
|
|
|
|
* Reset | 5 6 | GPIO0 GPIO2 PF15 // must be high (ESP3D software configures this with a pullup so OK to leave as floating)
|
|
|
|
|
* 3.3V| 7 8 | RX GPIO0 PF14 // Leave as unused (ESP3D software configures this with a pullup so OK to leave as floating)
|
|
|
|
|
* ￣￣
|
|
|
|
|
* W1
|
|
|
|
|
*/
|
2020-08-22 06:22:14 +00:00
|
|
|
#define ESP_WIFI_MODULE_COM 6 // Must also set either SERIAL_PORT or SERIAL_PORT_2 to this
|
2020-06-21 08:46:31 +00:00
|
|
|
#define ESP_WIFI_MODULE_BAUDRATE BAUDRATE // Must use same BAUDRATE as SERIAL_PORT & SERIAL_PORT_2
|
|
|
|
|
#define ESP_WIFI_MODULE_RESET_PIN PG0
|
|
|
|
|
#define ESP_WIFI_MODULE_ENABLE_PIN PG1
|
|
|
|
|
#define ESP_WIFI_MODULE_GPIO0_PIN PF14
|
|
|
|
|
#define ESP_WIFI_MODULE_GPIO2_PIN PF15
|
