muele-marlin/Marlin/pins_PRINTRBOARD.h

/**
 * Printrboard pin assignments (AT90USB1286)
 * Requires the Teensyduino software with Teensy++ 2.0 selected in Arduino IDE!
 * http://www.pjrc.com/teensy/teensyduino.html
 * See http://reprap.org/wiki/Printrboard for more info
 */

#ifndef __AVR_AT90USB1286__
  #error Oops!  Make sure you have 'Teensy++ 2.0' selected from the 'Tools -> Boards' menu.
#endif

#ifdef AT90USBxx_TEENSYPP_ASSIGNMENTS  // use Teensyduino Teensy++2.0 pin assignments instead of Marlin traditional.
  #error These Printrboard assignments depend on traditional Marlin assignments, not AT90USBxx_TEENSYPP_ASSIGNMENTS in fastio.h
#endif

#define AT90USB 1286  // Disable MarlinSerial etc.

#define LARGE_FLASH        true

#define X_STEP_PIN          0
#define X_DIR_PIN           1
#define X_ENABLE_PIN       39

#define Y_STEP_PIN          2
#define Y_DIR_PIN           3
#define Y_ENABLE_PIN       38

#define Z_STEP_PIN          4
#define Z_DIR_PIN           5
#define Z_ENABLE_PIN       23

#define E0_STEP_PIN         6
#define E0_DIR_PIN          7
#define E0_ENABLE_PIN      19

#define HEATER_0_PIN       21  // Extruder
#define HEATER_1_PIN       46
#define HEATER_2_PIN       47
#define HEATER_BED_PIN     20

// If soft or fast PWM is off then use Teensyduino pin numbering, Marlin
// fastio pin numbering otherwise
#ifdef FAN_SOFT_PWM || FAST_PWM_FAN
  #define FAN_PIN          22
#else
  #define FAN_PIN          16
#endif

#define X_STOP_PIN         35
#define Y_STOP_PIN          8
#define Z_STOP_PIN         36
#define TEMP_0_PIN          1  // Extruder / Analog pin numbering
#define TEMP_BED_PIN        0  // Bed / Analog pin numbering

#ifdef FILAMENT_SENSOR
  #define FILWIDTH_PIN      2
#endif

#define TEMP_1_PIN         -1
#define TEMP_2_PIN         -1

////LCD Pin Setup////

#define SDPOWER            -1
#define SDSS                8
#define LED_PIN            -1
#define PS_ON_PIN          -1
#define KILL_PIN           -1
#define ALARM_PIN          -1

#ifndef SDSUPPORT
// these pins are defined in the SD library if building with SD support
  #define SCK_PIN           9
  #define MISO_PIN         11
  #define MOSI_PIN         10
#endif

#if defined(ULTRA_LCD) && defined(NEWPANEL)
  //we have no buzzer installed
  #define BEEPER -1
  //LCD Pins
  #ifdef LCD_I2C_PANELOLU2
    #define BTN_EN1 27  //RX1 - fastio.h pin mapping 27
    #define BTN_EN2 26  //TX1 - fastio.h pin mapping 26
    #define BTN_ENC 43 //A3 - fastio.h pin mapping 43
    #define SDSS   40 //use SD card on Panelolu2 (Teensyduino pin mapping)
  #endif // LCD_I2C_PANELOLU2
  //not connected to a pin
  #define SDCARDDETECT -1    
#endif // ULTRA_LCD && NEWPANEL

#if defined(VIKI2) || defined(miniVIKI)
 #define BEEPER 32 //FastIO
 // Pins for DOGM SPI LCD Support
 #define DOGLCD_A0  42 //Non-FastIO
 #define DOGLCD_CS  43 //Non-FastIO
 #define LCD_SCREEN_ROT_180
 
 //The encoder and click button (FastIO Pins)
 #define BTN_EN1 26 
 #define BTN_EN2 27
 #define BTN_ENC 47  //the click switch

 #define SDSS 45
 #define SDCARDDETECT -1 // FastIO (Manual says 72 I'm not certain cause I can't test) 

 #ifdef TEMP_STAT_LEDS
  #define STAT_LED_RED      12 //Non-FastIO
  #define STAT_LED_BLUE     10 //Non-FastIO
 #endif  
#endif