2015-01-26 02:40:00 +00:00
/**
* Sanguinololu board pin assignments
*/
# if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega1284P__)
# error Oops! Make sure you have 'Sanguino' selected from the 'Tools -> Boards' menu.
# endif
# define X_STEP_PIN 15
# define X_DIR_PIN 21
# define X_STOP_PIN 18
# define Y_STEP_PIN 22
# define Y_DIR_PIN 23
# define Y_STOP_PIN 19
2015-07-23 19:33:22 +00:00
# define Z_STEP_PIN 3
# define Z_DIR_PIN 2
2015-01-26 02:40:00 +00:00
# define Z_STOP_PIN 20
# define E0_STEP_PIN 1
# define E0_DIR_PIN 0
# define LED_PIN -1
# define FAN_PIN -1
2015-07-23 19:33:22 +00:00
# if MB(AZTEEG_X1) || MB(STB_11) || MB(MELZI)
# define FAN_PIN 4 // Works for Panelolu2 too
# if MB(MELZI)
# define LED_PIN 27 // On some broken versions of the Sanguino libraries the pin definitions are wrong, so LED_PIN needs to be 28. But you should upgrade your Sanguino libraries! See #368.
# elif MB(STB_11)
# define LCD_PIN_BL 17 // LCD backlight LED
# endif
2015-01-26 02:40:00 +00:00
# endif
2015-07-31 05:11:19 +00:00
# if ENABLED(Z_PROBE_SLED)
2015-05-12 06:51:01 +00:00
# define SLED_PIN -1
2015-05-11 21:22:19 +00:00
# endif
2015-07-31 05:11:19 +00:00
# if HAS_SERVOS
2015-07-23 19:33:22 +00:00
# define SERVO0_PIN -1
2015-01-26 02:40:00 +00:00
# if NUM_SERVOS > 1
2015-07-23 19:33:22 +00:00
# define SERVO1_PIN -1
2015-06-28 02:20:32 +00:00
# if NUM_SERVOS > 2
2015-07-23 19:33:22 +00:00
# define SERVO2_PIN -1
2015-06-28 02:20:32 +00:00
# if NUM_SERVOS > 3
2015-07-23 19:33:22 +00:00
# define SERVO3_PIN -1
2015-06-28 02:20:32 +00:00
# endif
# endif
2015-01-26 02:40:00 +00:00
# endif
# endif
# define PS_ON_PIN -1
# define KILL_PIN -1
# define HEATER_0_PIN 13 // (extruder)
# define HEATER_1_PIN -1
# define HEATER_2_PIN -1
2015-07-31 05:11:19 +00:00
# if ENABLED(SANGUINOLOLU_V_1_2)
2015-01-26 02:40:00 +00:00
2015-07-23 19:33:22 +00:00
# define HEATER_BED_PIN 12 // (bed)
# define X_ENABLE_PIN 14
# define Y_ENABLE_PIN 14
# define Z_ENABLE_PIN 26
# define E0_ENABLE_PIN 14
2015-01-26 02:40:00 +00:00
2015-07-31 05:11:19 +00:00
# if ENABLED(LCD_I2C_PANELOLU2)
2015-07-23 19:33:22 +00:00
# define FAN_PIN 4 // Uses Transistor1 (PWM) on Panelolu2's Sanguino Adapter Board to drive the fan
2015-01-26 02:40:00 +00:00
# endif
# else
2015-07-23 19:33:22 +00:00
# define HEATER_BED_PIN 14 // (bed)
# define X_ENABLE_PIN -1
# define Y_ENABLE_PIN -1
# define Z_ENABLE_PIN -1
# define E0_ENABLE_PIN -1
2015-01-26 02:40:00 +00:00
# endif
# define TEMP_0_PIN 7 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 33 extruder)
# define TEMP_1_PIN -1
# define TEMP_2_PIN -1
# define TEMP_BED_PIN 6 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!! (pin 34 bed)
# define SDPOWER -1
# define SDSS 31
2015-07-23 19:33:22 +00:00
/**
* On some broken versions of the Sanguino libraries the pin definitions are wrong ,
* which then needs SDSS as pin 24. But you should upgrade your Sanguino libraries ! See # 368.
*/
2015-01-26 02:40:00 +00:00
//#define SDSS 24
2015-07-31 05:11:19 +00:00
# if ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL)
2015-07-23 19:33:22 +00:00
// No buzzer installed
2015-07-31 06:19:11 +00:00
# define BEEPER_PIN -1
2015-07-23 19:33:22 +00:00
// LCD Pins
2015-07-31 05:11:19 +00:00
# if ENABLED(DOGLCD)
2015-07-23 19:33:22 +00:00
2015-07-31 05:11:19 +00:00
# if ENABLED(U8GLIB_ST7920) //SPI GLCD 12864 ST7920 ( like [www.digole.com] ) For Melzi V2.0
2015-07-23 19:33:22 +00:00
# if MB(MELZI) // Melzi board
# define LCD_PINS_RS 30 //CS chip select /SS chip slave select
# define LCD_PINS_ENABLE 29 //SID (MOSI)
# define LCD_PINS_D4 17 //SCK (CLK) clock
2015-07-31 06:19:11 +00:00
# define BEEPER_PIN 27 // Pin 27 is taken by LED_PIN, but Melzi LED does nothing with Marlin so this can be used for BEEPER_PIN. You can use this pin with M42 instead of BEEPER_PIN.
2015-07-23 19:33:22 +00:00
# else // Sanguinololu 1.3
# define LCD_PINS_RS 4
# define LCD_PINS_ENABLE 17
# define LCD_PINS_D4 30
# define LCD_PINS_D5 29
# define LCD_PINS_D6 28
# define LCD_PINS_D7 27
# endif
# else // DOGM SPI LCD Support
# define DOGLCD_A0 30
# define DOGLCD_CS 29
# define LCD_CONTRAST 1
# endif
// Uncomment screen orientation
# define LCD_SCREEN_ROT_0
// #define LCD_SCREEN_ROT_90
// #define LCD_SCREEN_ROT_180
// #define LCD_SCREEN_ROT_270
# else // !DOGLCD - Standard Hitachi LCD controller
# define LCD_PINS_RS 4
# define LCD_PINS_ENABLE 17
# define LCD_PINS_D4 30
# define LCD_PINS_D5 29
# define LCD_PINS_D6 28
# define LCD_PINS_D7 27
# endif // !DOGLCD
//The encoder and click button
# define BTN_EN1 11
# define BTN_EN2 10
2015-07-31 05:11:19 +00:00
# if ENABLED(LCD_I2C_PANELOLU2)
2015-07-23 19:33:22 +00:00
# if MB(MELZI)
# define BTN_ENC 29
# define LCD_SDSS 30 // Panelolu2 SD card reader rather than the Melzi
# else
# define BTN_ENC 30
# endif
# else
# define BTN_ENC 16
# define LCD_SDSS 28 // Smart Controller SD card reader rather than the Melzi
# endif //Panelolu2
2015-07-31 23:40:50 +00:00
# define SD_DETECT_PIN -1
2015-07-23 19:33:22 +00:00
2015-07-31 05:11:19 +00:00
# elif ENABLED(MAKRPANEL)
2015-07-23 19:33:22 +00:00
2015-07-31 06:19:11 +00:00
# define BEEPER_PIN 29
2015-07-31 05:11:19 +00:00
2015-01-26 02:40:00 +00:00
// Pins for DOGM SPI LCD Support
2015-07-23 19:33:22 +00:00
# define DOGLCD_A0 30
# define DOGLCD_CS 17
# define LCD_PIN_BL 28 // backlight LED on PA3
2015-01-26 02:40:00 +00:00
// GLCD features
2015-07-23 19:33:22 +00:00
# define LCD_CONTRAST 1
2015-01-26 02:40:00 +00:00
// Uncomment screen orientation
# define LCD_SCREEN_ROT_0
// #define LCD_SCREEN_ROT_90
// #define LCD_SCREEN_ROT_180
// #define LCD_SCREEN_ROT_270
//The encoder and click button
2015-07-23 19:33:22 +00:00
# define BTN_EN1 11
# define BTN_EN2 10
# define BTN_ENC 16
2015-07-31 23:40:50 +00:00
# define SD_DETECT_PIN -1
2015-01-26 02:40:00 +00:00
2015-07-23 19:33:22 +00:00
# endif // MAKRPANEL
// #if FAN_PIN == 12 || FAN_PIN ==13
// #define FAN_SOFT_PWM
// #endif