muele-marlin/Marlin/src/gcode/bedlevel/G26.cpp

/**
 * Marlin 3D Printer Firmware
 * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
 *
 * Based on Sprinter and grbl.
 * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 3 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 *
 */

/**
 *   G26 Mesh Validation Tool
 *
 *   G26 is a Mesh Validation Tool intended to provide support for the Marlin Unified Bed Leveling System.
 *   In order to fully utilize and benefit from the Marlin Unified Bed Leveling System an accurate Mesh must
 *   be defined. G29 is designed to allow the user to quickly validate the correctness of her Mesh. It will
 *   first heat the bed and nozzle. It will then print lines and circles along the Mesh Cell boundaries and
 *   the intersections of those lines (respectively).
 *
 *   This action allows the user to immediately see where the Mesh is properly defined and where it needs to
 *   be edited. The command will generate the Mesh lines closest to the nozzle's starting position. Alternatively
 *   the user can specify the X and Y position of interest with command parameters. This allows the user to
 *   focus on a particular area of the Mesh where attention is needed.
 *
 *   B #  Bed         Set the Bed Temperature. If not specified, a default of 60 C. will be assumed.
 *
 *   C    Current     When searching for Mesh Intersection points to draw, use the current nozzle location
 *                    as the base for any distance comparison.
 *
 *   D    Disable     Disable the Unified Bed Leveling System. In the normal case the user is invoking this
 *                    command to see how well a Mesh as been adjusted to match a print surface. In order to do
 *                    this the Unified Bed Leveling System is turned on by the G26 command. The D parameter
 *                    alters the command's normal behavior and disables the Unified Bed Leveling System even if
 *                    it is on.
 *
 *   H #  Hotend      Set the Nozzle Temperature. If not specified, a default of 205 C. will be assumed.
 *
 *   I #  Preset      Heat the Nozzle and Bed based on a Material Preset (if material presets are defined).
 *
 *   F #  Filament    Used to specify the diameter of the filament being used. If not specified
 *                    1.75mm filament is assumed. If you are not getting acceptable results by using the
 *                    'correct' numbers, you can scale this number up or down a little bit to change the amount
 *                    of filament that is being extruded during the printing of the various lines on the bed.
 *
 *   K    Keep-On     Keep the heaters turned on at the end of the command.
 *
 *   L #  Layer       Layer height. (Height of nozzle above bed)  If not specified .20mm will be used.
 *
 *   O #  Ooooze      How much your nozzle will Ooooze filament while getting in position to print. This
 *                    is over kill, but using this parameter will let you get the very first 'circle' perfect
 *                    so you have a trophy to peel off of the bed and hang up to show how perfectly you have your
 *                    Mesh calibrated. If not specified, a filament length of .3mm is assumed.
 *
 *   P #  Prime       Prime the nozzle with specified length of filament. If this parameter is not
 *                    given, no prime action will take place. If the parameter specifies an amount, that much
 *                    will be purged before continuing. If no amount is specified the command will start
 *                    purging filament until the user provides an LCD Click and then it will continue with
 *                    printing the Mesh. You can carefully remove the spent filament with a needle nose
 *                    pliers while holding the LCD Click wheel in a depressed state. If you do not have
 *                    an LCD, you must specify a value if you use P.
 *
 *   Q #  Multiplier  Retraction Multiplier. Normally not needed. Retraction defaults to 1.0mm and
 *                    un-retraction is at 1.2mm   These numbers will be scaled by the specified amount
 *
 *   R #  Repeat      Prints the number of patterns given as a parameter, starting at the current location.
 *                    If a parameter isn't given, every point will be printed unless G26 is interrupted.
 *                    This works the same way that the UBL G29 P4 R parameter works.
 *
 *                    NOTE:  If you do not have an LCD, you -must- specify R. This is to ensure that you are
 *                    aware that there's some risk associated with printing without the ability to abort in
 *                    cases where mesh point Z value may be inaccurate. As above, if you do not include a
 *                    parameter, every point will be printed.
 *
 *   S #  Nozzle      Used to control the size of nozzle diameter. If not specified, a .4mm nozzle is assumed.
 *
 *   U #  Random      Randomize the order that the circles are drawn on the bed. The search for the closest
 *                    un-drawn circle is still done. But the distance to the location for each circle has a
 *                    random number of the specified size added to it. Specifying S50 will give an interesting
 *                    deviation from the normal behavior on a 10 x 10 Mesh.
 *
 *   X #  X Coord.    Specify the starting location of the drawing activity.
 *
 *   Y #  Y Coord.    Specify the starting location of the drawing activity.
 */

#include "../../inc/MarlinConfig.h"

#if ENABLED(G26_MESH_VALIDATION)

#define G26_OK false
#define G26_ERR true

#include "../../gcode/gcode.h"
#include "../../feature/bedlevel/bedlevel.h"

#include "../../MarlinCore.h"
#include "../../module/planner.h"
#include "../../module/stepper.h"
#include "../../module/motion.h"
#include "../../module/tool_change.h"
#include "../../module/temperature.h"
#include "../../lcd/ultralcd.h"

#define EXTRUSION_MULTIPLIER 1.0
#define PRIME_LENGTH 10.0
#define OOZE_AMOUNT 0.3

#define INTERSECTION_CIRCLE_RADIUS 5
#define CROSSHAIRS_SIZE 3

#ifndef G26_RETRACT_MULTIPLIER
  #define G26_RETRACT_MULTIPLIER 1.0 // x 1mm
#endif

#ifndef G26_XY_FEEDRATE
  #define G26_XY_FEEDRATE (PLANNER_XY_FEEDRATE() / 3.0)
#endif

#if CROSSHAIRS_SIZE >= INTERSECTION_CIRCLE_RADIUS
  #error "CROSSHAIRS_SIZE must be less than INTERSECTION_CIRCLE_RADIUS."
#endif

#define G26_OK false
#define G26_ERR true

#if ENABLED(ARC_SUPPORT)
  void plan_arc(const xyze_pos_t &cart, const ab_float_t &offset, const uint8_t clockwise);
#endif

constexpr float g26_e_axis_feedrate = 0.025;

static MeshFlags circle_flags, horizontal_mesh_line_flags, vertical_mesh_line_flags;
float g26_random_deviation = 0.0;

static bool g26_retracted = false; // Track the retracted state of the nozzle so mismatched
                                   // retracts/recovers won't result in a bad state.

float g26_extrusion_multiplier,
      g26_retraction_multiplier,
      g26_layer_height,
      g26_prime_length;

xy_pos_t g26_xy_pos; // = { 0, 0 }

int16_t g26_bed_temp,
        g26_hotend_temp;

int8_t g26_prime_flag;

#if HAS_LCD_MENU

  /**
   * If the LCD is clicked, cancel, wait for release, return true
   */
  bool user_canceled() {
    if (!ui.button_pressed()) return false; // Return if the button isn't pressed
    ui.set_status_P(GET_TEXT(MSG_G26_CANCELED), 99);
    TERN_(HAS_LCD_MENU, ui.quick_feedback());
    ui.wait_for_release();
    return true;
  }

#endif

mesh_index_pair find_closest_circle_to_print(const xy_pos_t &pos) {
  float closest = 99999.99;
  mesh_index_pair out_point;

  out_point.pos = -1;

  GRID_LOOP(i, j) {
    if (!circle_flags.marked(i, j)) {
      // We found a circle that needs to be printed
      const xy_pos_t m = { _GET_MESH_X(i), _GET_MESH_Y(j) };

      // Get the distance to this intersection
      float f = (pos - m).magnitude();

      // It is possible that we are being called with the values
      // to let us find the closest circle to the start position.
      // But if this is not the case, add a small weighting to the
      // distance calculation to help it choose a better place to continue.
      f += (g26_xy_pos - m).magnitude() / 15.0f;

      // Add the specified amount of Random Noise to our search
      if (g26_random_deviation > 1.0) f += random(0.0, g26_random_deviation);

      if (f < closest) {
        closest = f;          // Found a closer un-printed location
        out_point.pos.set(i, j);  // Save its data
        out_point.distance = closest;
      }
    }
  }
  circle_flags.mark(out_point); // Mark this location as done.
  return out_point;
}

void move_to(const float &rx, const float &ry, const float &z, const float &e_delta) {
  static float last_z = -999.99;

  const xy_pos_t dest = { rx, ry };

  const bool has_xy_component = dest != current_position; // Check if X or Y is involved in the movement.

  destination = current_position;

  if (z != last_z) {
    last_z = destination.z = z;
    const feedRate_t feed_value = planner.settings.max_feedrate_mm_s[Z_AXIS] * 0.5f; // Use half of the Z_AXIS max feed rate
    prepare_internal_move_to_destination(feed_value);
    destination = current_position;
  }

  // If X or Y is involved do a 'normal' move. Otherwise retract/recover/hop.
  destination = dest;
  destination.e += e_delta;
  const feedRate_t feed_value = has_xy_component ? feedRate_t(G26_XY_FEEDRATE) : planner.settings.max_feedrate_mm_s[E_AXIS] * 0.666f;
  prepare_internal_move_to_destination(feed_value);
  destination = current_position;
}

FORCE_INLINE void move_to(const xyz_pos_t &where, const float &de) { move_to(where.x, where.y, where.z, de); }

void retract_filament(const xyz_pos_t &where) {
  if (!g26_retracted) { // Only retract if we are not already retracted!
    g26_retracted = true;
    move_to(where, -1.0f * g26_retraction_multiplier);
  }
}

// TODO: Parameterize the Z lift with a define
void retract_lift_move(const xyz_pos_t &s) {
  retract_filament(destination);
  move_to(current_position.x, current_position.y, current_position.z + 0.5f, 0.0);  // Z lift to minimize scraping
  move_to(s.x, s.y, s.z + 0.5f, 0.0);  // Get to the starting point with no extrusion while lifted
}

void recover_filament(const xyz_pos_t &where) {
  if (g26_retracted) { // Only un-retract if we are retracted.
    move_to(where, 1.2f * g26_retraction_multiplier);
    g26_retracted = false;
  }
}

/**
 * print_line_from_here_to_there() takes two cartesian coordinates and draws a line from one
 * to the other. But there are really three sets of coordinates involved. The first coordinate
 * is the present location of the nozzle. We don't necessarily want to print from this location.
 * We first need to move the nozzle to the start of line segment where we want to print. Once
 * there, we can use the two coordinates supplied to draw the line.
 *
 * Note:  Although we assume the first set of coordinates is the start of the line and the second
 * set of coordinates is the end of the line, it does not always work out that way. This function
 * optimizes the movement to minimize the travel distance before it can start printing. This saves
 * a lot of time and eliminates a lot of nonsensical movement of the nozzle. However, it does
 * cause a lot of very little short retracement of th nozzle when it draws the very first line
 * segment of a 'circle'. The time this requires is very short and is easily saved by the other
 * cases where the optimization comes into play.
 */
void print_line_from_here_to_there(const xyz_pos_t &s, const xyz_pos_t &e) {

  // Distances to the start / end of the line
  xy_float_t svec = current_position - s, evec = current_position - e;

  const float dist_start = HYPOT2(svec.x, svec.y),
              dist_end = HYPOT2(evec.x, evec.y),
              line_length = HYPOT(e.x - s.x, e.y - s.y);

  // If the end point of the line is closer to the nozzle, flip the direction,
  // moving from the end to the start. On very small lines the optimization isn't worth it.
  if (dist_end < dist_start && (INTERSECTION_CIRCLE_RADIUS) < ABS(line_length))
    return print_line_from_here_to_there(e, s);

  // Decide whether to retract & lift
  if (dist_start > 2.0) retract_lift_move(s);

  move_to(s, 0.0); // Get to the starting point with no extrusion / un-Z lift

  const float e_pos_delta = line_length * g26_e_axis_feedrate * g26_extrusion_multiplier;

  recover_filament(destination);
  move_to(e, e_pos_delta);  // Get to the ending point with an appropriate amount of extrusion
}

inline bool look_for_lines_to_connect() {
  xyz_pos_t s, e;
  s.z = e.z = g26_layer_height;

  GRID_LOOP(i, j) {

    if (TERN0(HAS_LCD_MENU, user_canceled())) return true;

    if (i < (GRID_MAX_POINTS_X)) {  // Can't connect to anything farther to the right than GRID_MAX_POINTS_X.
                                    // Already a half circle at the edge of the bed.

      if (circle_flags.marked(i, j) && circle_flags.marked(i + 1, j)) {   // Test whether a leftward line can be done
        if (!horizontal_mesh_line_flags.marked(i, j)) {
          // Two circles need a horizontal line to connect them
          s.x = _GET_MESH_X(  i  ) + (INTERSECTION_CIRCLE_RADIUS - (CROSSHAIRS_SIZE)); // right edge
          e.x = _GET_MESH_X(i + 1) - (INTERSECTION_CIRCLE_RADIUS - (CROSSHAIRS_SIZE)); // left edge

          LIMIT(s.x, X_MIN_POS + 1, X_MAX_POS - 1);
          s.y = e.y = constrain(_GET_MESH_Y(j), Y_MIN_POS + 1, Y_MAX_POS - 1);
          LIMIT(e.x, X_MIN_POS + 1, X_MAX_POS - 1);

          if (position_is_reachable(s.x, s.y) && position_is_reachable(e.x, e.y))
            print_line_from_here_to_there(s, e);

          horizontal_mesh_line_flags.mark(i, j); // Mark done, even if skipped
        }
      }

      if (j < (GRID_MAX_POINTS_Y)) {  // Can't connect to anything further back than GRID_MAX_POINTS_Y.
                                      // Already a half circle at the edge of the bed.

        if (circle_flags.marked(i, j) && circle_flags.marked(i, j + 1)) {   // Test whether a downward line can be done
          if (!vertical_mesh_line_flags.marked(i, j)) {
            // Two circles that need a vertical line to connect them
            s.y = _GET_MESH_Y(  j  ) + (INTERSECTION_CIRCLE_RADIUS - (CROSSHAIRS_SIZE)); // top edge
            e.y = _GET_MESH_Y(j + 1) - (INTERSECTION_CIRCLE_RADIUS - (CROSSHAIRS_SIZE)); // bottom edge

            s.x = e.x = constrain(_GET_MESH_X(i), X_MIN_POS + 1, X_MAX_POS - 1);
            LIMIT(s.y, Y_MIN_POS + 1, Y_MAX_POS - 1);
            LIMIT(e.y, Y_MIN_POS + 1, Y_MAX_POS - 1);

            if (position_is_reachable(s.x, s.y) && position_is_reachable(e.x, e.y))
              print_line_from_here_to_there(s, e);

            vertical_mesh_line_flags.mark(i, j); // Mark done, even if skipped
          }
        }
      }
    }
  }
  return false;
}

/**
 * Turn on the bed and nozzle heat and
 * wait for them to get up to temperature.
 */
inline bool turn_on_heaters() {

  SERIAL_ECHOLNPGM("Waiting for heatup.");

  #if HAS_HEATED_BED

    if (g26_bed_temp > 25) {
      #if HAS_SPI_LCD
        ui.set_status_P(GET_TEXT(MSG_G26_HEATING_BED), 99);
        ui.quick_feedback();
        TERN_(HAS_LCD_MENU, ui.capture());
      #endif
      thermalManager.setTargetBed(g26_bed_temp);

      // Wait for the temperature to stabilize
      if (!thermalManager.wait_for_bed(true
          #if G26_CLICK_CAN_CANCEL
            , true
          #endif
        )
      ) return G26_ERR;
    }

  #endif // HAS_HEATED_BED

  // Start heating the active nozzle
  #if HAS_SPI_LCD
    ui.set_status_P(GET_TEXT(MSG_G26_HEATING_NOZZLE), 99);
    ui.quick_feedback();
  #endif
  thermalManager.setTargetHotend(g26_hotend_temp, active_extruder);

  // Wait for the temperature to stabilize
  if (!thermalManager.wait_for_hotend(active_extruder, true
    #if G26_CLICK_CAN_CANCEL
      , true
    #endif
  )) return G26_ERR;

  #if HAS_SPI_LCD
    ui.reset_status();
    ui.quick_feedback();
  #endif

  return G26_OK;
}

/**
 * Prime the nozzle if needed. Return true on error.
 */
inline bool prime_nozzle() {

  const feedRate_t fr_slow_e = planner.settings.max_feedrate_mm_s[E_AXIS] / 15.0f;
  #if HAS_LCD_MENU && DISABLED(TOUCH_BUTTONS) // ui.button_pressed issue with touchscreen
    #if ENABLED(PREVENT_LENGTHY_EXTRUDE)
      float Total_Prime = 0.0;
    #endif

    if (g26_prime_flag == -1) {  // The user wants to control how much filament gets purged
      ui.capture();
      ui.set_status_P(GET_TEXT(MSG_G26_MANUAL_PRIME), 99);
      ui.chirp();

      destination = current_position;

      recover_filament(destination); // Make sure G26 doesn't think the filament is retracted().

      while (!ui.button_pressed()) {
        ui.chirp();
        destination.e += 0.25;
        #if ENABLED(PREVENT_LENGTHY_EXTRUDE)
          Total_Prime += 0.25;
          if (Total_Prime >= EXTRUDE_MAXLENGTH) {
            ui.release();
            return G26_ERR;
          }
        #endif
        prepare_internal_move_to_destination(fr_slow_e);
        destination = current_position;
        planner.synchronize();    // Without this synchronize, the purge is more consistent,
                                  // but because the planner has a buffer, we won't be able
                                  // to stop as quickly. So we put up with the less smooth
                                  // action to give the user a more responsive 'Stop'.
      }

      ui.wait_for_release();

      ui.set_status_P(GET_TEXT(MSG_G26_PRIME_DONE), 99);
      ui.quick_feedback();
      ui.release();
    }
    else
  #endif
  {
    #if HAS_SPI_LCD
      ui.set_status_P(GET_TEXT(MSG_G26_FIXED_LENGTH), 99);
      ui.quick_feedback();
    #endif
    destination = current_position;
    destination.e += g26_prime_length;
    prepare_internal_move_to_destination(fr_slow_e);
    destination.e -= g26_prime_length;
    retract_filament(destination);
  }

  return G26_OK;
}

/**
 * G26: Mesh Validation Pattern generation.
 *
 * Used to interactively edit the mesh by placing the
 * nozzle in a problem area and doing a G29 P4 R command.
 *
 * Parameters:
 *
 *  B  Bed Temperature
 *  C  Continue from the Closest mesh point
 *  D  Disable leveling before starting
 *  F  Filament diameter
 *  H  Hotend Temperature
 *  K  Keep heaters on when completed
 *  L  Layer Height
 *  O  Ooze extrusion length
 *  P  Prime length
 *  Q  Retraction multiplier
 *  R  Repetitions (number of grid points)
 *  S  Nozzle Size (diameter) in mm
 *  T  Tool index to change to, if included
 *  U  Random deviation (50 if no value given)
 *  X  X position
 *  Y  Y position
 */
void GcodeSuite::G26() {
  SERIAL_ECHOLNPGM("G26 starting...");

  // Don't allow Mesh Validation without homing first,
  // or if the parameter parsing did not go OK, abort
  if (axis_unhomed_error()) return;

  // Change the tool first, if specified
  if (parser.seenval('T')) tool_change(parser.value_int());

  g26_extrusion_multiplier    = EXTRUSION_MULTIPLIER;
  g26_retraction_multiplier   = G26_RETRACT_MULTIPLIER;
  g26_layer_height            = MESH_TEST_LAYER_HEIGHT;
  g26_prime_length            = PRIME_LENGTH;
  g26_bed_temp                = MESH_TEST_BED_TEMP;
  g26_hotend_temp             = MESH_TEST_HOTEND_TEMP;
  g26_prime_flag              = 0;

  float g26_nozzle            = MESH_TEST_NOZZLE_SIZE,
        g26_filament_diameter = DEFAULT_NOMINAL_FILAMENT_DIA,
        g26_ooze_amount       = parser.linearval('O', OOZE_AMOUNT);

  bool g26_continue_with_closest = parser.boolval('C'),
       g26_keep_heaters_on       = parser.boolval('K');

  // Accept 'I' if temperature presets are defined
  const uint8_t preset_index = (0
    #if PREHEAT_COUNT
      + (parser.seenval('I') ? _MIN(parser.value_byte(), PREHEAT_COUNT - 1) + 1 : 0)
    #endif
  );

  #if HAS_HEATED_BED

    // Get a temperature from 'I' or 'B'
    int16_t bedtemp = 0;

    // Use the 'I' index if temperature presets are defined
    #if PREHEAT_COUNT
      if (preset_index) bedtemp = ui.material_preset[preset_index - 1].bed_temp;
    #endif

    // Look for 'B' Bed Temperature
    if (parser.seenval('B')) bedtemp = parser.value_celsius();

    if (bedtemp) {
      if (!WITHIN(bedtemp, 40, BED_MAX_TARGET)) {
        SERIAL_ECHOLNPAIR("?Specified bed temperature not plausible (40-", int(BED_MAX_TARGET), "C).");
        return;
      }
      g26_bed_temp = bedtemp;
    }

  #endif // HAS_HEATED_BED

  if (parser.seenval('L')) {
    g26_layer_height = parser.value_linear_units();
    if (!WITHIN(g26_layer_height, 0.0, 2.0)) {
      SERIAL_ECHOLNPGM("?Specified layer height not plausible.");
      return;
    }
  }

  if (parser.seen('Q')) {
    if (parser.has_value()) {
      g26_retraction_multiplier = parser.value_float();
      if (!WITHIN(g26_retraction_multiplier, 0.05, 15.0)) {
        SERIAL_ECHOLNPGM("?Specified Retraction Multiplier not plausible.");
        return;
      }
    }
    else {
      SERIAL_ECHOLNPGM("?Retraction Multiplier must be specified.");
      return;
    }
  }

  if (parser.seenval('S')) {
    g26_nozzle = parser.value_float();
    if (!WITHIN(g26_nozzle, 0.1, 2.0)) {
      SERIAL_ECHOLNPGM("?Specified nozzle size not plausible.");
      return;
    }
  }

  if (parser.seen('P')) {
    if (!parser.has_value()) {
      #if HAS_LCD_MENU
        g26_prime_flag = -1;
      #else
        SERIAL_ECHOLNPGM("?Prime length must be specified when not using an LCD.");
        return;
      #endif
    }
    else {
      g26_prime_flag++;
      g26_prime_length = parser.value_linear_units();
      if (!WITHIN(g26_prime_length, 0.0, 25.0)) {
        SERIAL_ECHOLNPGM("?Specified prime length not plausible.");
        return;
      }
    }
  }

  if (parser.seenval('F')) {
    g26_filament_diameter = parser.value_linear_units();
    if (!WITHIN(g26_filament_diameter, 1.0, 4.0)) {
      SERIAL_ECHOLNPGM("?Specified filament size not plausible.");
      return;
    }
  }
  g26_extrusion_multiplier *= sq(1.75) / sq(g26_filament_diameter); // If we aren't using 1.75mm filament, we need to
                                                                    // scale up or down the length needed to get the
                                                                    // same volume of filament

  g26_extrusion_multiplier *= g26_filament_diameter * sq(g26_nozzle) / sq(0.3); // Scale up by nozzle size

  // Get a temperature from 'I' or 'H'
  int16_t noztemp = 0;

  // Accept 'I' if temperature presets are defined
  #if PREHEAT_COUNT
    if (preset_index) noztemp = ui.material_preset[preset_index - 1].hotend_temp;
  #endif

  // Look for 'H' Hotend Temperature
  if (parser.seenval('H')) noztemp = parser.value_celsius();

  // If any preset or temperature was specified
  if (noztemp) {
    if (!WITHIN(noztemp, 165, (HEATER_0_MAXTEMP) - (HOTEND_OVERSHOOT))) {
      SERIAL_ECHOLNPGM("?Specified nozzle temperature not plausible.");
      return;
    }
    g26_hotend_temp = noztemp;
  }

  // 'U' to Randomize and optionally set circle deviation
  if (parser.seen('U')) {
    randomSeed(millis());
    // This setting will persist for the next G26
    g26_random_deviation = parser.has_value() ? parser.value_float() : 50.0;
  }

  // Get repeat from 'R', otherwise do one full circuit
  int16_t g26_repeats;
  #if HAS_LCD_MENU
    g26_repeats = parser.intval('R', GRID_MAX_POINTS + 1);
  #else
    if (!parser.seen('R')) {
      SERIAL_ECHOLNPGM("?(R)epeat must be specified when not using an LCD.");
      return;
    }
    else
      g26_repeats = parser.has_value() ? parser.value_int() : GRID_MAX_POINTS + 1;
  #endif
  if (g26_repeats < 1) {
    SERIAL_ECHOLNPGM("?(R)epeat value not plausible; must be at least 1.");
    return;
  }

  // Set a position with 'X' and/or 'Y'. Default: current_position
  g26_xy_pos.set(parser.seenval('X') ? RAW_X_POSITION(parser.value_linear_units()) : current_position.x,
                 parser.seenval('Y') ? RAW_Y_POSITION(parser.value_linear_units()) : current_position.y);
  if (!position_is_reachable(g26_xy_pos)) {
    SERIAL_ECHOLNPGM("?Specified X,Y coordinate out of bounds.");
    return;
  }

  /**
   * Wait until all parameters are verified before altering the state!
   */
  set_bed_leveling_enabled(!parser.seen('D'));

  do_z_clearance(Z_CLEARANCE_BETWEEN_PROBES);

  #if DISABLED(NO_VOLUMETRICS)
    bool volumetric_was_enabled = parser.volumetric_enabled;
    parser.volumetric_enabled = false;
    planner.calculate_volumetric_multipliers();
  #endif

  if (turn_on_heaters() != G26_OK) goto LEAVE;

  current_position.e = 0.0;
  sync_plan_position_e();

  if (g26_prime_flag && prime_nozzle() != G26_OK) goto LEAVE;

  /**
   *  Bed is preheated
   *
   *  Nozzle is at temperature
   *
   *  Filament is primed!
   *
   *  It's  "Show Time" !!!
   */

  circle_flags.reset();
  horizontal_mesh_line_flags.reset();
  vertical_mesh_line_flags.reset();

  // Move nozzle to the specified height for the first layer
  destination = current_position;
  destination.z = g26_layer_height;
  move_to(destination, 0.0);
  move_to(destination, g26_ooze_amount);

  TERN_(HAS_LCD_MENU, ui.capture());

  #if DISABLED(ARC_SUPPORT)

    /**
     * Pre-generate radius offset values at 30 degree intervals to reduce CPU load.
     */
    #define A_INT 30
    #define _ANGS (360 / A_INT)
    #define A_CNT (_ANGS / 2)
    #define _IND(A) ((A + _ANGS * 8) % _ANGS)
    #define _COS(A) (trig_table[_IND(A) % A_CNT] * (_IND(A) >= A_CNT ? -1 : 1))
    #define _SIN(A) (-_COS((A + A_CNT / 2) % _ANGS))
    #if A_CNT & 1
      #error "A_CNT must be a positive value. Please change A_INT."
    #endif
    float trig_table[A_CNT];
    LOOP_L_N(i, A_CNT)
      trig_table[i] = INTERSECTION_CIRCLE_RADIUS * cos(RADIANS(i * A_INT));

  #endif // !ARC_SUPPORT

  mesh_index_pair location;
  do {
    // Find the nearest confluence
    location = find_closest_circle_to_print(g26_continue_with_closest ? xy_pos_t(current_position) : g26_xy_pos);

    if (location.valid()) {
      const xy_pos_t circle = _GET_MESH_POS(location.pos);

      // If this mesh location is outside the printable radius, skip it.
      if (!position_is_reachable(circle)) continue;

      // Determine where to start and end the circle,
      // which is always drawn counter-clockwise.
      const xy_int8_t st = location;
      const bool f = st.y == 0,
                 r = st.x >= GRID_MAX_POINTS_X - 1,
                 b = st.y >= GRID_MAX_POINTS_Y - 1;

      #if ENABLED(ARC_SUPPORT)

        #define ARC_LENGTH(quarters)  (INTERSECTION_CIRCLE_RADIUS * M_PI * (quarters) / 2)
        #define INTERSECTION_CIRCLE_DIAM  ((INTERSECTION_CIRCLE_RADIUS) * 2)

        xy_float_t e = { circle.x + INTERSECTION_CIRCLE_RADIUS, circle.y };
        xyz_float_t s = e;

        // Figure out where to start and end the arc - we always print counterclockwise
        float arc_length = ARC_LENGTH(4);
        if (st.x == 0) {                             // left edge
          if (!f) { s.x = circle.x; s.y -= INTERSECTION_CIRCLE_RADIUS; }
          if (!b) { e.x = circle.x; e.y += INTERSECTION_CIRCLE_RADIUS; }
          arc_length = (f || b) ? ARC_LENGTH(1) : ARC_LENGTH(2);
        }
        else if (r) {                             // right edge
          if (b) s.set(circle.x - (INTERSECTION_CIRCLE_RADIUS), circle.y);
          else   s.set(circle.x, circle.y + INTERSECTION_CIRCLE_RADIUS);
          if (f) e.set(circle.x - (INTERSECTION_CIRCLE_RADIUS), circle.y);
          else   e.set(circle.x, circle.y - (INTERSECTION_CIRCLE_RADIUS));
          arc_length = (f || b) ? ARC_LENGTH(1) : ARC_LENGTH(2);
        }
        else if (f) {
          e.x -= INTERSECTION_CIRCLE_DIAM;
          arc_length = ARC_LENGTH(2);
        }
        else if (b) {
          s.x -= INTERSECTION_CIRCLE_DIAM;
          arc_length = ARC_LENGTH(2);
        }

        const ab_float_t arc_offset = circle - s;
        const xy_float_t dist = current_position - s;   // Distance from the start of the actual circle
        const float dist_start = HYPOT2(dist.x, dist.y);
        const xyze_pos_t endpoint = {
          e.x, e.y, g26_layer_height,
          current_position.e + (arc_length * g26_e_axis_feedrate * g26_extrusion_multiplier)
        };

        if (dist_start > 2.0) {
          s.z = g26_layer_height + 0.5f;
          retract_lift_move(s);
        }

        s.z = g26_layer_height;
        move_to(s, 0.0);  // Get to the starting point with no extrusion / un-Z lift

        recover_filament(destination);

        const feedRate_t old_feedrate = feedrate_mm_s;
        feedrate_mm_s = PLANNER_XY_FEEDRATE() * 0.1f;
        plan_arc(endpoint, arc_offset, false);  // Draw a counter-clockwise arc
        feedrate_mm_s = old_feedrate;
        destination = current_position;

        if (TERN0(HAS_LCD_MENU, user_canceled())) goto LEAVE; // Check if the user wants to stop the Mesh Validation

      #else // !ARC_SUPPORT

        int8_t start_ind = -2, end_ind = 9; // Assume a full circle (from 5:00 to 5:00)
        if (st.x == 0) {                    // Left edge? Just right half.
          start_ind = f ? 0 : -3;           //  03:00 to 12:00 for front-left
          end_ind = b ? 0 : 2;              //  06:00 to 03:00 for back-left
        }
        else if (r) {                       // Right edge? Just left half.
          start_ind = b ? 6 : 3;            //  12:00 to 09:00 for front-right
          end_ind = f ? 5 : 8;              //  09:00 to 06:00 for back-right
        }
        else if (f) {                       // Front edge? Just back half.
          start_ind = 0;                    //  03:00
          end_ind = 5;                      //  09:00
        }
        else if (b) {                       // Back edge? Just front half.
          start_ind = 6;                    //  09:00
          end_ind = 11;                     //  03:00
        }

        for (int8_t ind = start_ind; ind <= end_ind; ind++) {

          if (TERN0(HAS_LCD_MENU, user_canceled())) goto LEAVE; // Check if the user wants to stop the Mesh Validation

          xyz_float_t p = { circle.x + _COS(ind    ), circle.y + _SIN(ind    ), g26_layer_height },
                      q = { circle.x + _COS(ind + 1), circle.y + _SIN(ind + 1), g26_layer_height };

          #if IS_KINEMATIC
            // Check to make sure this segment is entirely on the bed, skip if not.
            if (!position_is_reachable(p) || !position_is_reachable(q)) continue;
          #else
            LIMIT(p.x, X_MIN_POS + 1, X_MAX_POS - 1); // Prevent hitting the endstops
            LIMIT(p.y, Y_MIN_POS + 1, Y_MAX_POS - 1);
            LIMIT(q.x, X_MIN_POS + 1, X_MAX_POS - 1);
            LIMIT(q.y, Y_MIN_POS + 1, Y_MAX_POS - 1);
          #endif

          print_line_from_here_to_there(p, q);
          SERIAL_FLUSH();   // Prevent host M105 buffer overrun.
        }

      #endif // !ARC_SUPPORT

      if (look_for_lines_to_connect()) goto LEAVE;
    }

    SERIAL_FLUSH(); // Prevent host M105 buffer overrun.

  } while (--g26_repeats && location.valid());

  LEAVE:
  ui.set_status_P(GET_TEXT(MSG_G26_LEAVING), -1);

  retract_filament(destination);
  destination.z = Z_CLEARANCE_BETWEEN_PROBES;
  move_to(destination, 0);                                    // Raise the nozzle

  destination = g26_xy_pos;                                   // Move back to the starting XY position
  move_to(destination, 0);                                    // Move back to the starting position

  #if DISABLED(NO_VOLUMETRICS)
    parser.volumetric_enabled = volumetric_was_enabled;
    planner.calculate_volumetric_multipliers();
  #endif

  TERN_(HAS_LCD_MENU, ui.release()); // Give back control of the LCD

  if (!g26_keep_heaters_on) {
    TERN_(HAS_HEATED_BED, thermalManager.setTargetBed(0));
    thermalManager.setTargetHotend(active_extruder, 0);
  }
}

#endif // G26_MESH_VALIDATION