From 00fed0a7038bbd7acaf7808ffbcd616ec154d963 Mon Sep 17 00:00:00 2001
From: Bas Spaans <bas.spaans@gmail.com>
Date: Thu, 31 Jan 2013 18:11:13 +0100
Subject: [PATCH] Revert "Extended comment explaining M42 usage"

This reverts commit 01541ee64ca1239c9bfa593c54085ae78e0b78ec.
---
 Marlin/Marlin_main.cpp | 28 ++++++++++------------------
 1 file changed, 10 insertions(+), 18 deletions(-)

diff --git a/Marlin/Marlin_main.cpp b/Marlin/Marlin_main.cpp
index 1f2f34646c..473d205e9e 100644
--- a/Marlin/Marlin_main.cpp
+++ b/Marlin/Marlin_main.cpp
@@ -88,7 +88,7 @@
 // M29  - Stop SD write
 // M30  - Delete file from SD (M30 filename.g)
 // M31  - Output time since last M109 or SD card start to serial
-// M42  - Change pin status via gcode. Use M42 Px Sy to set pin x to value y, when omitting Px the onboard led will be used.
+// M42  - Change pin status via gcode
 // M80  - Turn on Power Supply
 // M81  - Turn off Power Supply
 // M82  - Set E codes absolute (default)
@@ -124,8 +124,7 @@
 // M500 - stores paramters in EEPROM
 // M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).  
 // M502 - reverts to the default "factory settings".  You still need to store them in EEPROM afterwards if you want to.
-// M503 - print the current settings (from memory not from eeprom)
-
+// M503 - print the current settings (from memory not from eeprom)
 // M540 - Use S[0|1] to enable or disable the stop SD card print on endstop hit (requires ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED)
 // M600 - Pause for filament change X[pos] Y[pos] Z[relative lift] E[initial retract] L[later retract distance for removal]
 // M907 - Set digital trimpot motor current using axis codes.
@@ -959,7 +958,7 @@ void process_commands()
       autotempShutdown();
       }
       break;
-    case 42: //M42 -Change pin status via gcode 
+    case 42: //M42 -Change pin status via gcode
       if (code_seen('S'))
       {
         int pin_status = code_value();
@@ -1500,20 +1499,13 @@ void process_commands()
     {
         Config_PrintSettings();
     }
-    break;
-
-    #ifdef ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED
-
-    case 540:
-
-    {
-
-        if(code_seen('S')) abort_on_endstop_hit = code_value() > 0;
-
-    }
-
-    break;
-
+    break;
+    #ifdef ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED
+    case 540:
+    {
+        if(code_seen('S')) abort_on_endstop_hit = code_value() > 0;
+    }
+    break;
     #endif
     #ifdef FILAMENTCHANGEENABLE
     case 600: //Pause for filament change X[pos] Y[pos] Z[relative lift] E[initial retract] L[later retract distance for removal]