diff --git a/Marlin/Makefile b/Marlin/Makefile index da3897e807..095944138f 100644 --- a/Marlin/Makefile +++ b/Marlin/Makefile @@ -89,8 +89,8 @@ WIRE ?= 0 # this defines if U8GLIB is needed (may require RELOC_WORKAROUND) U8GLIB ?= 1 -# this defines whether to include the Trinamic TMC2630Stepper -TMC2630 ?= 1 +# this defines whether to include the Trinamic TMCStepper library +TMC ?= 1 ############ # Try to automatically determine whether RELOC_WORKAROUND is needed based @@ -103,7 +103,7 @@ CC_PATCHLEVEL:=$(shell $(CC) -dM -E - < /dev/null | grep __GNUC_PATCHLEVEL__ | c CC_VER:=$(shell echo $$(( $(CC_MAJ) * 10000 + $(CC_MIN) * 100 + $(CC_PATCHLEVEL) ))) ifeq ($(shell test $(CC_VER) -lt 40901 && echo 1),1) @echo This version of GCC is likely broken. Enabling relocation workaround. - RELOC_WORKAROUND = 1 + RELOC_WORKAROUND = 1 endif ############################################################################ @@ -195,7 +195,7 @@ else ifeq ($(HARDWARE_MOTHERBOARD),49) else ifeq ($(HARDWARE_MOTHERBOARD),7) # Ultimaker (Older electronics. Pre 1.5.4. This is rare) else ifeq ($(HARDWARE_MOTHERBOARD),71) -MCU ?= atmega1280 + MCU ?= atmega1280 # Azteeg X3 else ifeq ($(HARDWARE_MOTHERBOARD),67) # Azteeg X3 Pro @@ -265,9 +265,9 @@ else ifeq ($(HARDWARE_MOTHERBOARD),75) # else ifeq ($(HARDWARE_MOTHERBOARD),702) -MCU ?= atmega1281 + MCU ?= atmega1281 else ifeq ($(HARDWARE_MOTHERBOARD),25) -MCU ?= atmega1281 + MCU ?= atmega1281 # # Sanguinololu and Derivatives - ATmega644P, ATmega1284P @@ -275,44 +275,44 @@ MCU ?= atmega1281 # Sanguinololu < 1.2 else ifeq ($(HARDWARE_MOTHERBOARD),6) -HARDWARE_VARIANT ?= Sanguino -MCU ?= atmega644p + HARDWARE_VARIANT ?= Sanguino + MCU ?= atmega644p # Sanguinololu 1.2 and above else ifeq ($(HARDWARE_MOTHERBOARD),62) -HARDWARE_VARIANT ?= Sanguino -MCU ?= atmega644p + HARDWARE_VARIANT ?= Sanguino + MCU ?= atmega644p # Melzi else ifeq ($(HARDWARE_MOTHERBOARD),63) -HARDWARE_VARIANT ?= Sanguino -MCU ?= atmega644p + HARDWARE_VARIANT ?= Sanguino + MCU ?= atmega644p # Melzi with ATmega1284 (MaKr3d version) else ifeq ($(HARDWARE_MOTHERBOARD),66) -HARDWARE_VARIANT ?= Sanguino -MCU ?= atmega1284p + HARDWARE_VARIANT ?= Sanguino + MCU ?= atmega1284p # Melzi Creality3D board (for CR-10 etc) else ifeq ($(HARDWARE_MOTHERBOARD),89) -HARDWARE_VARIANT ?= Sanguino -MCU ?= atmega1284p + HARDWARE_VARIANT ?= Sanguino + MCU ?= atmega1284p # Melzi Malyan M150 board else ifeq ($(HARDWARE_MOTHERBOARD),92) -HARDWARE_VARIANT ?= Sanguino -MCU ?= atmega1284p + HARDWARE_VARIANT ?= Sanguino + MCU ?= atmega1284p # Tronxy X5S else ifeq ($(HARDWARE_MOTHERBOARD),505) -HARDWARE_VARIANT ?= Sanguino -MCU ?= atmega1284p + HARDWARE_VARIANT ?= Sanguino + MCU ?= atmega1284p # STB V1.1 else ifeq ($(HARDWARE_MOTHERBOARD),64) -HARDWARE_VARIANT ?= Sanguino -MCU ?= atmega1284p + HARDWARE_VARIANT ?= Sanguino + MCU ?= atmega1284p # Azteeg X1 else ifeq ($(HARDWARE_MOTHERBOARD),65) -HARDWARE_VARIANT ?= Sanguino -MCU ?= atmega1284p + HARDWARE_VARIANT ?= Sanguino + MCU ?= atmega1284p # Anet 1.0 (Melzi clone) else ifeq ($(HARDWARE_MOTHERBOARD),69) -HARDWARE_VARIANT ?= Sanguino -MCU ?= atmega1284p + HARDWARE_VARIANT ?= Sanguino + MCU ?= atmega1284p # # Other ATmega644P, ATmega644, ATmega1284P @@ -320,52 +320,52 @@ MCU ?= atmega1284p # Gen3 Monolithic Electronics else ifeq ($(HARDWARE_MOTHERBOARD),22) -HARDWARE_VARIANT ?= Sanguino -MCU ?= atmega644p + HARDWARE_VARIANT ?= Sanguino + MCU ?= atmega644p # Gen3+ else ifeq ($(HARDWARE_MOTHERBOARD),9) -HARDWARE_VARIANT ?= Sanguino -MCU ?= atmega644p + HARDWARE_VARIANT ?= Sanguino + MCU ?= atmega644p # Gen6 else ifeq ($(HARDWARE_MOTHERBOARD),5) -HARDWARE_VARIANT ?= Gen6 -MCU ?= atmega644p + HARDWARE_VARIANT ?= Gen6 + MCU ?= atmega644p # Gen6 deluxe else ifeq ($(HARDWARE_MOTHERBOARD),51) -HARDWARE_VARIANT ?= Gen6 -MCU ?= atmega644p + HARDWARE_VARIANT ?= Gen6 + MCU ?= atmega644p # Gen7 custom (Alfons3 Version) else ifeq ($(HARDWARE_MOTHERBOARD),10) -HARDWARE_VARIANT ?= Gen7 -MCU ?= atmega644 -F_CPU ?= 20000000 + HARDWARE_VARIANT ?= Gen7 + MCU ?= atmega644 + F_CPU ?= 20000000 # Gen7 v1.1, v1.2 else ifeq ($(HARDWARE_MOTHERBOARD),11) -HARDWARE_VARIANT ?= Gen7 -MCU ?= atmega644p -F_CPU ?= 20000000 + HARDWARE_VARIANT ?= Gen7 + MCU ?= atmega644p + F_CPU ?= 20000000 # Gen7 v1.3 else ifeq ($(HARDWARE_MOTHERBOARD),12) -HARDWARE_VARIANT ?= Gen7 -MCU ?= atmega644p -F_CPU ?= 20000000 + HARDWARE_VARIANT ?= Gen7 + MCU ?= atmega644p + F_CPU ?= 20000000 # Gen7 v1.4 else ifeq ($(HARDWARE_MOTHERBOARD),13) -HARDWARE_VARIANT ?= Gen7 -MCU ?= atmega1284p -F_CPU ?= 20000000 + HARDWARE_VARIANT ?= Gen7 + MCU ?= atmega1284p + F_CPU ?= 20000000 # Alpha OMCA board else ifeq ($(HARDWARE_MOTHERBOARD),90) -HARDWARE_VARIANT ?= SanguinoA -MCU ?= atmega644 + HARDWARE_VARIANT ?= SanguinoA + MCU ?= atmega644 # Final OMCA board else ifeq ($(HARDWARE_MOTHERBOARD),91) -HARDWARE_VARIANT ?= Sanguino -MCU ?= atmega644p + HARDWARE_VARIANT ?= Sanguino + MCU ?= atmega644p # Sethi 3D_1 else ifeq ($(HARDWARE_MOTHERBOARD),20) -HARDWARE_VARIANT ?= Sanguino -MCU ?= atmega644p + HARDWARE_VARIANT ?= Sanguino + MCU ?= atmega644p # # Teensyduino - AT90USB1286, AT90USB1286P @@ -373,37 +373,43 @@ MCU ?= atmega644p # Teensylu else ifeq ($(HARDWARE_MOTHERBOARD),8) -HARDWARE_VARIANT ?= Teensy -MCU ?= at90usb1286 + HARDWARE_VARIANT ?= Teensy + MCU ?= at90usb1286 # Printrboard (AT90USB1286) else ifeq ($(HARDWARE_MOTHERBOARD),81) -HARDWARE_VARIANT ?= Teensy -MCU ?= at90usb1286 + HARDWARE_VARIANT ?= Teensy + MCU ?= at90usb1286 # Printrboard Revision F (AT90USB1286) else ifeq ($(HARDWARE_MOTHERBOARD),811) -HARDWARE_VARIANT ?= Teensy -MCU ?= at90usb1286 + HARDWARE_VARIANT ?= Teensy + MCU ?= at90usb1286 # Brainwave (AT90USB646) else ifeq ($(HARDWARE_MOTHERBOARD),82) -HARDWARE_VARIANT ?= Teensy -MCU ?= at90usb646 + HARDWARE_VARIANT ?= Teensy + MCU ?= at90usb646 # Brainwave Pro (AT90USB1286) else ifeq ($(HARDWARE_MOTHERBOARD),83) -HARDWARE_VARIANT ?= Teensy -MCU ?= at90usb1286 + HARDWARE_VARIANT ?= Teensy + MCU ?= at90usb1286 # SAV Mk-I (AT90USB1286) else ifeq ($(HARDWARE_MOTHERBOARD),84) -HARDWARE_VARIANT ?= Teensy -MCU ?= at90usb1286 + HARDWARE_VARIANT ?= Teensy + MCU ?= at90usb1286 # Teensy++2.0 (AT90USB1286) else ifeq ($(HARDWARE_MOTHERBOARD),85) -HARDWARE_VARIANT ?= Teensy -MCU ?= at90usb1286 + HARDWARE_VARIANT ?= Teensy + MCU ?= at90usb1286 # 5DPrint D8 Driver Board else ifeq ($(HARDWARE_MOTHERBOARD),88) -HARDWARE_VARIANT ?= Teensy -MCU ?= at90usb1286 + HARDWARE_VARIANT ?= Teensy + MCU ?= at90usb1286 +# UltiMachine Archim2 (with TMC2130 drivers) +else ifeq ($(HARDWARE_MOTHERBOARD),1590) + HARDWARE_VARIANT ?= archim + MCPU = cortex-m3 + F_CPU = 84000000L + IS_MCU = 0 endif # Be sure to regenerate speed_lookuptable.h with create_speed_lookuptable.py @@ -411,9 +417,22 @@ endif # Set to 16Mhz if not yet set. F_CPU ?= 16000000 -# Set to arduino, ATmega2560 if not yet set. -HARDWARE_VARIANT ?= arduino -MCU ?= atmega2560 +# Set to microcontroller if IS_MCU not yet set +IS_MCU ?= 1 + +ifeq ($(IS_MCU),1) + # Set to arduino, ATmega2560 if not yet set. + HARDWARE_VARIANT ?= arduino + MCU ?= atmega2560 + + TOOL_PREFIX = avr + MCU_FLAGS = -mmcu=$(MCU) + SIZE_FLAGS = --mcu=$(MCU) -C +else + TOOL_PREFIX = arm-none-eabi + CPU_FLAGS = -mthumb -mcpu=$(MCPU) + SIZE_FLAGS = -A +endif # Arduino contained the main source code for the Arduino # Libraries, the "hardware variant" are for boards @@ -434,19 +453,19 @@ VPATH = . VPATH += $(BUILD_DIR) VPATH += $(HARDWARE_SRC) -# U8glib -VPATH += $(ARDUINO_USER_DIR)/libraries/U8glib -VPATH += $(ARDUINO_USER_DIR)/libraries/U8glib/clib - ifeq ($(HARDWARE_VARIANT), $(filter $(HARDWARE_VARIANT),arduino Teensy Sanguino)) VPATH += $(ARDUINO_INSTALL_DIR)/hardware/marlin/avr/libraries/LiquidCrystal/src VPATH += $(ARDUINO_INSTALL_DIR)/hardware/marlin/avr/libraries/SPI endif -VPATH += $(ARDUINO_INSTALL_DIR)/hardware/arduino/avr/cores/arduino +ifeq ($(IS_MCU),1) + VPATH += $(ARDUINO_INSTALL_DIR)/hardware/arduino/avr/cores/arduino + + VPATH += $(ARDUINO_INSTALL_DIR)/hardware/arduino/avr/libraries/SPI + VPATH += $(ARDUINO_INSTALL_DIR)/hardware/arduino/avr/libraries/SPI/src + VPATH += $(ARDUINO_INSTALL_DIR)/hardware/arduino/avr/libraries/SoftwareSerial/src +endif -VPATH += $(ARDUINO_INSTALL_DIR)/hardware/arduino/avr/libraries/SPI -VPATH += $(ARDUINO_INSTALL_DIR)/hardware/arduino/avr/libraries/SPI/src VPATH += $(ARDUINO_INSTALL_DIR)/libraries/LiquidCrystal/src ifeq ($(LIQUID_TWI2), 1) VPATH += $(ARDUINO_INSTALL_DIR)/libraries/Wire @@ -462,71 +481,89 @@ VPATH += $(ARDUINO_INSTALL_DIR)/libraries/Adafruit_NeoPixel endif ifeq ($(U8GLIB), 1) VPATH += $(ARDUINO_INSTALL_DIR)/libraries/U8glib -VPATH += $(ARDUINO_INSTALL_DIR)/libraries/U8glib/clib +VPATH += $(ARDUINO_INSTALL_DIR)/libraries/U8glib/csrc +VPATH += $(ARDUINO_INSTALL_DIR)/libraries/U8glib/cppsrc +VPATH += $(ARDUINO_INSTALL_DIR)/libraries/U8glib/fntsrc endif -ifeq ($(TMC2630), 1) -VPATH += $(ARDUINO_INSTALL_DIR)/libraries/TMC2130Stepper/src -VPATH += $(ARDUINO_INSTALL_DIR)/libraries/TMC2130Stepper/src/source +ifeq ($(TMC), 1) +VPATH += $(ARDUINO_INSTALL_DIR)/libraries/TMCStepper/src +VPATH += $(ARDUINO_INSTALL_DIR)/libraries/TMCStepper/src/source endif ifeq ($(HARDWARE_VARIANT), arduino) -HARDWARE_SUB_VARIANT ?= mega -VPATH += $(ARDUINO_INSTALL_DIR)/hardware/arduino/avr/variants/$(HARDWARE_SUB_VARIANT) + HARDWARE_SUB_VARIANT ?= mega + VPATH += $(ARDUINO_INSTALL_DIR)/hardware/arduino/avr/variants/$(HARDWARE_SUB_VARIANT) +else ifeq ($(HARDWARE_VARIANT), Sanguino) + VPATH += $(ARDUINO_INSTALL_DIR)/hardware/marlin/avr/variants/sanguino +else ifeq ($(HARDWARE_VARIANT), archim) + VPATH += $(ARDUINO_INSTALL_DIR)/packages/ultimachine/hardware/sam/1.6.9-b/system/libsam + VPATH += $(ARDUINO_INSTALL_DIR)/packages/ultimachine/hardware/sam/1.6.9-b/system/CMSIS/CMSIS/Include/ + VPATH += $(ARDUINO_INSTALL_DIR)/packages/ultimachine/hardware/sam/1.6.9-b/system/CMSIS/Device/ATMEL/ + VPATH += $(ARDUINO_INSTALL_DIR)/packages/ultimachine/hardware/sam/1.6.9-b/cores/arduino + VPATH += $(ARDUINO_INSTALL_DIR)/packages/ultimachine/hardware/sam/1.6.9-b/cores/arduino/avr + VPATH += $(ARDUINO_INSTALL_DIR)/packages/ultimachine/hardware/sam/1.6.9-b/cores/arduino/USB + VPATH += $(ARDUINO_INSTALL_DIR)/packages/ultimachine/hardware/sam/1.6.9-b/libraries/Wire/src + VPATH += $(ARDUINO_INSTALL_DIR)/packages/ultimachine/hardware/sam/1.6.9-b/libraries/SPI/src + VPATH += $(ARDUINO_INSTALL_DIR)/packages/ultimachine/hardware/sam/1.6.9-b/variants/archim + LDSCRIPT = $(ARDUINO_INSTALL_DIR)/packages/ultimachine/hardware/sam/1.6.9-b/variants/archim/linker_scripts/gcc/flash.ld + LDLIBS = $(ARDUINO_INSTALL_DIR)/packages/ultimachine/hardware/sam/1.6.9-b/variants/archim/libsam_sam3x8e_gcc_rel.a else -ifeq ($(HARDWARE_VARIANT), Sanguino) -VPATH += $(ARDUINO_INSTALL_DIR)/hardware/marlin/avr/variants/sanguino -else -HARDWARE_SUB_VARIANT ?= standard -VPATH += $(ARDUINO_INSTALL_DIR)/hardware/$(HARDWARE_VARIANT)/variants/$(HARDWARE_SUB_VARIANT) -endif + HARDWARE_SUB_VARIANT ?= standard + VPATH += $(ARDUINO_INSTALL_DIR)/hardware/$(HARDWARE_VARIANT)/variants/$(HARDWARE_SUB_VARIANT) endif + LIB_SRC = wiring.c \ - wiring_analog.c wiring_digital.c \ - wiring_pulse.c \ - wiring_shift.c WInterrupts.c hooks.c + wiring_analog.c wiring_digital.c \ + wiring_shift.c WInterrupts.c hooks.c + +ifeq ($(HARDWARE_VARIANT), archim) + LIB_ASRC += wiring_pulse_asm.S +else + LIB_SRC += wiring_pulse.c +endif ifeq ($(HARDWARE_VARIANT), Teensy) -LIB_SRC = wiring.c -VPATH += $(ARDUINO_INSTALL_DIR)/hardware/teensy/cores/teensy + LIB_SRC = wiring.c + VPATH += $(ARDUINO_INSTALL_DIR)/hardware/teensy/cores/teensy endif -LIB_CXXSRC = WMath.cpp WString.cpp Print.cpp SPI.cpp Tone.cpp +LIB_CXXSRC = WMath.cpp WString.cpp Print.cpp SPI.cpp ifeq ($(NEOPIXEL), 1) -LIB_CXXSRC += Adafruit_NeoPixel.cpp + LIB_CXXSRC += Adafruit_NeoPixel.cpp endif ifeq ($(LIQUID_TWI2), 0) -LIB_CXXSRC += LiquidCrystal.cpp + LIB_CXXSRC += LiquidCrystal.cpp else -LIB_SRC += twi.c -LIB_CXXSRC += Wire.cpp LiquidTWI2.cpp + LIB_SRC += twi.c + LIB_CXXSRC += Wire.cpp LiquidTWI2.cpp endif ifeq ($(WIRE), 1) -LIB_SRC += twi.c -LIB_CXXSRC += Wire.cpp + LIB_SRC += twi.c + LIB_CXXSRC += Wire.cpp endif ifeq ($(U8GLIB), 1) -LIB_CXXSRC += U8glib.cpp -LIB_SRC += u8g_ll_api.c u8g_bitmap.c u8g_clip.c u8g_com_null.c u8g_delay.c u8g_page.c u8g_pb.c u8g_pb16h1.c u8g_rect.c u8g_state.c u8g_font.c u8g_font_data.c + LIB_CXXSRC += U8glib.cpp + LIB_SRC += u8g_ll_api.c u8g_bitmap.c u8g_clip.c u8g_com_null.c u8g_delay.c u8g_page.c u8g_pb.c u8g_pb16h1.c u8g_rect.c u8g_state.c u8g_font.c u8g_font_6x13.c u8g_font_04b_03.c u8g_font_5x8.c endif -ifeq ($(TMC2630), 1) -LIB_CXXSRC += TMC2130Stepper.cpp TMC2130Stepper_COOLCONF.cpp TMC2130Stepper_DRV_STATUS.cpp TMC2130Stepper_IHOLD_IRUN.cpp TMC2130Stepper_CHOPCONF.cpp TMC2130Stepper_GCONF.cpp TMC2130Stepper_PWMCONF.cpp SW_SPI.cpp +ifeq ($(TMC), 1) + LIB_CXXSRC += TMCStepper.cpp COOLCONF.cpp DRV_STATUS.cpp IHOLD_IRUN.cpp CHOPCONF.cpp GCONF.cpp PWMCONF.cpp DRV_CONF.cpp DRVCONF.cpp DRVCTRL.cpp DRVSTATUS.cpp ENCMODE.cpp RAMP_STAT.cpp SGCSCONF.cpp SHORT_CONF.cpp SMARTEN.cpp SW_MODE.cpp SW_SPI.cpp TMC2130Stepper.cpp TMC2208Stepper.cpp TMC2660Stepper.cpp TMC5130Stepper.cpp TMC5160Stepper.cpp endif ifeq ($(RELOC_WORKAROUND), 1) -LD_PREFIX=-nodefaultlibs -LD_SUFFIX=-lm -lgcc -lc -lgcc + LD_PREFIX=-nodefaultlibs + LD_SUFFIX=-lm -lgcc -lc -lgcc endif #Check for Arduino 1.0.0 or higher and use the correct source files for that version ifeq ($(shell [ $(ARDUINO_VERSION) -ge 100 ] && echo true), true) -LIB_CXXSRC += main.cpp + LIB_CXXSRC += main.cpp else -LIB_SRC += pins_arduino.c main.c + LIB_SRC += pins_arduino.c main.c endif FORMAT = ihex @@ -544,62 +581,77 @@ OPT = s DEFINES ?= # Program settings -CC = $(AVR_TOOLS_PATH)avr-gcc -CXX = $(AVR_TOOLS_PATH)avr-g++ -OBJCOPY = $(AVR_TOOLS_PATH)avr-objcopy -OBJDUMP = $(AVR_TOOLS_PATH)avr-objdump -AR = $(AVR_TOOLS_PATH)avr-ar -SIZE = $(AVR_TOOLS_PATH)avr-size -NM = $(AVR_TOOLS_PATH)avr-nm +CC = $(AVR_TOOLS_PATH)$(TOOL_PREFIX)-gcc +CXX = $(AVR_TOOLS_PATH)$(TOOL_PREFIX)-g++ +OBJCOPY = $(AVR_TOOLS_PATH)$(TOOL_PREFIX)-objcopy +OBJDUMP = $(AVR_TOOLS_PATH)$(TOOL_PREFIX)-objdump +AR = $(AVR_TOOLS_PATH)$(TOOL_PREFIX)-ar +SIZE = $(AVR_TOOLS_PATH)$(TOOL_PREFIX)-size +NM = $(AVR_TOOLS_PATH)$(TOOL_PREFIX)-nm AVRDUDE = avrdude REMOVE = rm -f MV = mv -f # Place -D or -U options here -CDEFS = -DF_CPU=$(F_CPU) ${addprefix -D , $(DEFINES)} +CDEFS = -DF_CPU=$(F_CPU) ${addprefix -D , $(DEFINES)} -DARDUINO=$(ARDUINO_VERSION) CXXDEFS = $(CDEFS) ifeq ($(HARDWARE_VARIANT), Teensy) -CDEFS += -DUSB_SERIAL -LIB_SRC += usb.c pins_teensy.c -LIB_CXXSRC += usb_api.cpp + CDEFS += -DUSB_SERIAL + LIB_SRC += usb.c pins_teensy.c + LIB_CXXSRC += usb_api.cpp + +else ifeq ($(HARDWARE_VARIANT), archim) + CDEFS += -DARDUINO_SAM_ARCHIM -DARDUINO_ARCH_SAM -D__SAM3X8E__ -DUSB_VID=0x27b1 -DUSB_PID=0x0001 -DUSBCON '-DUSB_MANUFACTURER="UltiMachine"' '-DUSB_PRODUCT="Archim"' + LIB_CXXSRC += variant.cpp IPAddress.cpp Reset.cpp RingBuffer.cpp Stream.cpp UARTClass.cpp USARTClass.cpp abi.cpp new.cpp watchdog.cpp CDC.cpp PluggableUSB.cpp USBCore.cpp + LIB_SRC += cortex_handlers.c iar_calls_sam3.c syscalls_sam3.c dtostrf.c itoa.c endif # Add all the source directories as include directories too CINCS = ${addprefix -I ,${VPATH}} CXXINCS = ${addprefix -I ,${VPATH}} +# Silence warnings for library code (won't work for .h files, unfortunately) +LIBWARN = -w -Wno-packed-bitfield-compat + # Compiler flag to set the C/CPP Standard level. CSTANDARD = -std=gnu99 CXXSTANDARD = -std=gnu++11 CDEBUG = -g$(DEBUG) -CWARN = -Wall -Wstrict-prototypes -CTUNING = -w -fsigned-char -funsigned-bitfields -fpack-struct \ - -fshort-enums -ffunction-sections -fdata-sections -flto \ - -DARDUINO=$(ARDUINO_VERSION) +CWARN = -Wall -Wstrict-prototypes -Wno-packed-bitfield-compat -Wno-pragmas +CXXWARN = -Wall -Wno-packed-bitfield-compat -Wno-pragmas +CTUNING = -fsigned-char -funsigned-bitfields -fpack-struct -fno-exceptions \ + -fshort-enums -ffunction-sections -fdata-sections ifneq ($(HARDWARE_MOTHERBOARD),) -CTUNING += -DMOTHERBOARD=${HARDWARE_MOTHERBOARD} + CTUNING += -DMOTHERBOARD=${HARDWARE_MOTHERBOARD} endif #CEXTRA = -Wa,-adhlns=$(<:.c=.lst) -CEXTRA = -fno-use-cxa-atexit -fno-threadsafe-statics - -CFLAGS := $(CDEBUG) $(CDEFS) $(CINCS) -O$(OPT) $(CWARN) $(CEXTRA) $(CTUNING) $(CSTANDARD) -CXXFLAGS := $(CDEFS) $(CINCS) -O$(OPT) -Wall $(CEXTRA) $(CTUNING) $(CXXSTANDARD) +CXXEXTRA = -fno-use-cxa-atexit -fno-threadsafe-statics -fno-rtti +CFLAGS := $(CDEBUG) $(CDEFS) $(CINCS) -O$(OPT) $(CEXTRA) $(CTUNING) $(CSTANDARD) +CXXFLAGS := $(CDEFS) $(CINCS) -O$(OPT) $(CXXEXTRA) $(CTUNING) $(CXXSTANDARD) +ASFLAGS := $(CDEFS) #ASFLAGS = -Wa,-adhlns=$(<:.S=.lst),-gstabs -LDFLAGS = -lm - +ifeq ($(HARDWARE_VARIANT), archim) + LD_PREFIX = -Wl,--gc-sections,-Map,Marlin.ino.map,--cref,--check-sections,--entry=Reset_Handler,--unresolved-symbols=report-all,--warn-common,--warn-section-align + LD_SUFFIX = $(LDLIBS) + LDFLAGS = -lm -gcc -T$(LDSCRIPT) -u _sbrk -u link -u _close -u _fstat -u _isatty -u _lseek -u _read -u _write -u _exit -u kill -u _getpid +else + LD_PREFIX = -Wl,--gc-sections,--relax + LDFLAGS = -lm + CTUNING += -flto +endif # Programming support using avrdude. Settings and variables. AVRDUDE_PORT = $(UPLOAD_PORT) AVRDUDE_WRITE_FLASH = -Uflash:w:$(BUILD_DIR)/$(TARGET).hex:i ifeq ($(shell uname -s), Linux) -AVRDUDE_CONF = /etc/avrdude/avrdude.conf + AVRDUDE_CONF = /etc/avrdude/avrdude.conf else -AVRDUDE_CONF = $(ARDUINO_INSTALL_DIR)/hardware/tools/avr/etc/avrdude.conf + AVRDUDE_CONF = $(ARDUINO_INSTALL_DIR)/hardware/tools/avr/etc/avrdude.conf endif AVRDUDE_FLAGS = -D -C$(AVRDUDE_CONF) \ - -p$(MCU) -P$(AVRDUDE_PORT) -c$(AVRDUDE_PROGRAMMER) \ - -b$(UPLOAD_RATE) + -p$(MCU) -P$(AVRDUDE_PORT) -c$(AVRDUDE_PROGRAMMER) \ + -b$(UPLOAD_RATE) # Since Marlin 2.0, the source files may be distributed into several # different directories, so it is necessary to find them recursively @@ -619,17 +671,17 @@ LST = $(LIB_ASRC:.S=.lst) $(LIB_CXXSRC:.cpp=.lst) $(LIB_SRC:.c=.lst) # Combine all necessary flags and optional flags. # Add target processor to flags. -ALL_CFLAGS = -mmcu=$(MCU) -I. $(CFLAGS) -ALL_CXXFLAGS = -mmcu=$(MCU) $(CXXFLAGS) -ALL_ASFLAGS = -mmcu=$(MCU) -x assembler-with-cpp $(ASFLAGS) +ALL_CFLAGS = $(MCU_FLAGS) $(CPU_FLAGS) $(CFLAGS) -I. +ALL_CXXFLAGS = $(MCU_FLAGS) $(CPU_FLAGS) $(CXXFLAGS) +ALL_ASFLAGS = $(MCU_FLAGS) $(CPU_FLAGS) $(ASFLAGS) -x assembler-with-cpp # set V=1 (eg, "make V=1") to print the full commands etc. ifneq ($V,1) - Pecho=@echo - P=@ + Pecho=@echo + P=@ else - Pecho=@: - P= + Pecho=@: + P= endif # Create required build hierarchy if it does not exist @@ -639,9 +691,10 @@ $(shell mkdir -p $(dir $(OBJ))) # Default target. all: sizeafter -build: elf hex +build: elf hex bin elf: $(BUILD_DIR)/$(TARGET).elf +bin: $(BUILD_DIR)/$(TARGET).bin hex: $(BUILD_DIR)/$(TARGET).hex eep: $(BUILD_DIR)/$(TARGET).eep lss: $(BUILD_DIR)/$(TARGET).lss @@ -651,93 +704,101 @@ sym: $(BUILD_DIR)/$(TARGET).sym # Do not try to reset an Arduino if it's not one upload: $(BUILD_DIR)/$(TARGET).hex ifeq (${AVRDUDE_PROGRAMMER}, arduino) - stty hup < $(UPLOAD_PORT); true + stty hup < $(UPLOAD_PORT); true endif - $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) + $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) ifeq (${AVRDUDE_PROGRAMMER}, arduino) - stty -hup < $(UPLOAD_PORT); true + stty -hup < $(UPLOAD_PORT); true endif - # Display size of file. + # Display size of file. HEXSIZE = $(SIZE) --target=$(FORMAT) $(BUILD_DIR)/$(TARGET).hex -ELFSIZE = $(SIZE) --mcu=$(MCU) -C $(BUILD_DIR)/$(TARGET).elf; \ +ELFSIZE = $(SIZE) $(SIZE_FLAGS) $(BUILD_DIR)/$(TARGET).elf; \ $(SIZE) $(BUILD_DIR)/$(TARGET).elf sizebefore: - $P if [ -f $(BUILD_DIR)/$(TARGET).elf ]; then echo; echo $(MSG_SIZE_BEFORE); $(HEXSIZE); echo; fi + $P if [ -f $(BUILD_DIR)/$(TARGET).elf ]; then echo; echo $(MSG_SIZE_BEFORE); $(HEXSIZE); echo; fi sizeafter: build - $P if [ -f $(BUILD_DIR)/$(TARGET).elf ]; then echo; echo $(MSG_SIZE_AFTER); $(ELFSIZE); echo; fi + $P if [ -f $(BUILD_DIR)/$(TARGET).elf ]; then echo; echo $(MSG_SIZE_AFTER); $(ELFSIZE); echo; fi # Convert ELF to COFF for use in debugging / simulating in AVR Studio or VMLAB. COFFCONVERT=$(OBJCOPY) --debugging \ - --change-section-address .data-0x800000 \ - --change-section-address .bss-0x800000 \ - --change-section-address .noinit-0x800000 \ - --change-section-address .eeprom-0x810000 + --change-section-address .data-0x800000 \ + --change-section-address .bss-0x800000 \ + --change-section-address .noinit-0x800000 \ + --change-section-address .eeprom-0x810000 coff: $(BUILD_DIR)/$(TARGET).elf - $(COFFCONVERT) -O coff-avr $(BUILD_DIR)/$(TARGET).elf $(TARGET).cof + $(COFFCONVERT) -O coff-avr $(BUILD_DIR)/$(TARGET).elf $(TARGET).cof extcoff: $(TARGET).elf - $(COFFCONVERT) -O coff-ext-avr $(BUILD_DIR)/$(TARGET).elf $(TARGET).cof + $(COFFCONVERT) -O coff-ext-avr $(BUILD_DIR)/$(TARGET).elf $(TARGET).cof -.SUFFIXES: .elf .hex .eep .lss .sym +.SUFFIXES: .elf .hex .eep .lss .sym .bin .PRECIOUS: .o .elf.hex: - $(Pecho) " COPY $@" - $P $(OBJCOPY) -O $(FORMAT) -R .eeprom $< $@ + $(Pecho) " COPY $@" + $P $(OBJCOPY) -O $(FORMAT) -R .eeprom $< $@ + +.elf.bin: + $(Pecho) " COPY $@" + $P $(OBJCOPY) -O binary -R .eeprom $< $@ .elf.eep: - -$(OBJCOPY) -j .eeprom --set-section-flags=.eeprom="alloc,load" \ - --change-section-lma .eeprom=0 -O $(FORMAT) $< $@ + -$(OBJCOPY) -j .eeprom --set-section-flags=.eeprom="alloc,load" \ + --change-section-lma .eeprom=0 -O $(FORMAT) $< $@ # Create extended listing file from ELF output file. .elf.lss: - $(OBJDUMP) -h -S $< > $@ + $(OBJDUMP) -h -S $< > $@ # Create a symbol table from ELF output file. .elf.sym: - $(NM) -n $< > $@ + $(NM) -n $< > $@ - # Link: create ELF output file from library. + # Link: create ELF output file from library. $(BUILD_DIR)/$(TARGET).elf: $(OBJ) Configuration.h - $(Pecho) " CXX $@" - $P $(CC) $(LD_PREFIX) $(ALL_CXXFLAGS) -Wl,--gc-sections,--relax -o $@ -L. $(OBJ) $(LDFLAGS) $(LD_SUFFIX) + $(Pecho) " CXX $@" + $P $(CC) $(LD_PREFIX) $(ALL_CXXFLAGS) -o $@ -L. $(OBJ) $(LDFLAGS) $(LD_SUFFIX) # Object files that were found in "src" will be stored in $(BUILD_DIR) # in directories that mirror the structure of "src" $(BUILD_DIR)/%.o: %.c Configuration.h Configuration_adv.h $(MAKEFILE) - $(Pecho) " CC $<" - $P $(CC) -MMD -c $(ALL_CFLAGS) $< -o $@ + $(Pecho) " CC $<" + $P $(CC) -MMD -c $(ALL_CFLAGS) $(CWARN) $< -o $@ $(BUILD_DIR)/%.o: %.cpp Configuration.h Configuration_adv.h $(MAKEFILE) - $(Pecho) " CXX $<" - $P $(CXX) -MMD -c $(ALL_CXXFLAGS) $< -o $@ + $(Pecho) " CXX $<" + $P $(CXX) -MMD -c $(ALL_CXXFLAGS) $(CXXWARN) $< -o $@ # Object files for Arduino libs will be created in $(BUILD_DIR)/arduino $(BUILD_DIR)/arduino/%.o: %.c Configuration.h Configuration_adv.h $(MAKEFILE) - $(Pecho) " CC $<" - $P $(CC) -MMD -c $(ALL_CFLAGS) $< -o $@ + $(Pecho) " CC $<" + $P $(CC) -MMD -c $(ALL_CFLAGS) $(LIBWARN) $< -o $@ $(BUILD_DIR)/arduino/%.o: %.cpp Configuration.h Configuration_adv.h $(MAKEFILE) - $(Pecho) " CXX $<" - $P $(CXX) -MMD -c $(ALL_CXXFLAGS) $< -o $@ + $(Pecho) " CXX $<" + $P $(CXX) -MMD -c $(ALL_CXXFLAGS) $(LIBWARN) $< -o $@ + +$(BUILD_DIR)/arduino/%.o: %.S $(MAKEFILE) + $(Pecho) " CXX $<" + $P $(CXX) -MMD -c $(ALL_ASFLAGS) $< -o $@ # Target: clean project. clean: - $(Pecho) " RMDIR $(BUILD_DIR)/" - $P rm -rf $(BUILD_DIR) + $(Pecho) " RMDIR $(BUILD_DIR)/" + $P rm -rf $(BUILD_DIR) -.PHONY: all build elf hex eep lss sym program coff extcoff clean depend sizebefore sizeafter +.PHONY: all build elf hex eep lss sym program coff extcoff clean depend sizebefore sizeafter # Automaticaly include the dependency files created by gcc -include ${patsubst %.o, %.d, ${OBJ}}