Improved MKS Robin support (#19333)
This commit is contained in:
TheCodeExorcist
Scott Lahteine
parent
92eee0386f
commit
074d3f6266
|
|
@ -42,15 +42,20 @@
|
|||
#define DISABLE_JTAG
|
||||
|
||||
//
|
||||
// Enable SD EEPROM to prevent infinite boot loop
|
||||
// EEPROM
|
||||
//
|
||||
#ifdef ARDUINO_ARCH_STM32
|
||||
#define FLASH_EEPROM_EMULATION
|
||||
#if NO_EEPROM_SELECTED
|
||||
#ifdef ARDUINO_ARCH_STM32
|
||||
#define FLASH_EEPROM_EMULATION
|
||||
#else
|
||||
#define SDCARD_EEPROM_EMULATION
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#if ENABLED(FLASH_EEPROM_EMULATION)
|
||||
#define EEPROM_PAGE_SIZE (0x800U) // 2KB
|
||||
#define EEPROM_START_ADDRESS (0x8000000UL + (STM32_FLASH_SIZE) * 1024UL - (EEPROM_PAGE_SIZE) * 2UL)
|
||||
#define MARLIN_EEPROM_SIZE (EEPROM_PAGE_SIZE)
|
||||
#else
|
||||
#define SDCARD_EEPROM_EMULATION
|
||||
#endif
|
||||
|
||||
//
|
||||
|
|
@ -102,27 +107,56 @@
|
|||
#define TEMP_BED_PIN PC0 // TB1
|
||||
|
||||
//
|
||||
// Heaters / Fans
|
||||
// Heaters
|
||||
//
|
||||
#define HEATER_0_PIN PC7 // HEATER1
|
||||
#define HEATER_1_PIN PA6 // HEATER2
|
||||
#define HEATER_BED_PIN PC6 // HOT BED
|
||||
|
||||
//
|
||||
// Fan
|
||||
//
|
||||
#define FAN_PIN PA7 // FAN
|
||||
|
||||
/**
|
||||
* Note: MKS Robin board is using SPI2 interface. Make sure your stm32duino library is configured accordingly
|
||||
*/
|
||||
//
|
||||
// Thermocouples
|
||||
//
|
||||
//#define MAX6675_SS_PIN PE5 // TC1 - CS1
|
||||
//#define MAX6675_SS_PIN PE6 // TC2 - CS2
|
||||
|
||||
#define POWER_LOSS_PIN PA2 // PW_DET
|
||||
#define PS_ON_PIN PA3 // PW_OFF
|
||||
//
|
||||
// Filament runout sensor
|
||||
//
|
||||
#define FIL_RUNOUT_PIN PF11 // MT_DET
|
||||
|
||||
//
|
||||
// Power loss detection
|
||||
//
|
||||
#define POWER_LOSS_PIN PA2 // PW_DET
|
||||
|
||||
//
|
||||
// Power supply control
|
||||
//
|
||||
#define PS_ON_PIN PA3 // PW_OFF
|
||||
|
||||
//
|
||||
// Piezzoelectric speaker
|
||||
//
|
||||
#define BEEPER_PIN PC13
|
||||
|
||||
//
|
||||
// Activity LED
|
||||
//
|
||||
#define LED_PIN PB2
|
||||
|
||||
//
|
||||
// ESP12-S Wi-Fi module
|
||||
//
|
||||
#define WIFI_IO0_PIN PG1
|
||||
|
||||
//
|
||||
// LCD screen
|
||||
//
|
||||
#if HAS_FSMC_TFT
|
||||
/**
|
||||
* Note: MKS Robin TFT screens use various TFT controllers
|
||||
|
|
@ -151,6 +185,7 @@
|
|||
|
||||
#define TOUCH_BUTTONS_HW_SPI
|
||||
#define TOUCH_BUTTONS_HW_SPI_DEVICE 2
|
||||
#define TFT_BUFFER_SIZE 14400
|
||||
#endif
|
||||
|
||||
#if NEED_TOUCH_PINS
|
||||
|
|
@ -161,6 +196,7 @@
|
|||
#define TOUCH_INT_PIN -1
|
||||
#endif
|
||||
|
||||
// SPI2 is shared by LCD touch driver and flash
|
||||
// SPI1(PA7) & SPI3(PB5) not available
|
||||
#define SPI_DEVICE 2
|
||||
|
||||
|
|
@ -193,31 +229,55 @@
|
|||
#define SD_DETECT_PIN -1
|
||||
#endif
|
||||
|
||||
//
|
||||
// Trinamic TMC2208/2209 UART
|
||||
//
|
||||
#if HAS_TMC_UART
|
||||
/**
|
||||
* TMC2208/TMC2209 stepper drivers
|
||||
* This board does not have dedicated TMC UART pins. Custom wiring is needed.
|
||||
* You may uncomment one of the options below, or add it to your Configuration.h.
|
||||
*
|
||||
* Hardware serial communication ports.
|
||||
* If undefined software serial is used according to the pins below
|
||||
* When using up to four TMC2209 drivers, hardware serial is recommented on
|
||||
* MSerial0 or MSerial1.
|
||||
*
|
||||
* When using TMC2208 or more than four drivers, SoftwareSerial will be needed,
|
||||
* to provide dedicated pins for each drier.
|
||||
*/
|
||||
//#define X_HARDWARE_SERIAL MSerial1
|
||||
//#define Y_HARDWARE_SERIAL MSerial1
|
||||
//#define Z_HARDWARE_SERIAL MSerial1
|
||||
//#define E0_HARDWARE_SERIAL MSerial1
|
||||
//#define E1_HARDWARE_SERIAL MSerial1
|
||||
|
||||
// Unused servo pins may be repurposed with SoftwareSerialM
|
||||
//#define X_SERIAL_TX_PIN PF8 // SERVO3_PIN -- XS2 - 6
|
||||
//#define Y_SERIAL_TX_PIN PF9 // SERVO2_PIN -- XS2 - 5
|
||||
//#define Z_SERIAL_TX_PIN PA1 // SERVO1_PIN -- XS1 - 6
|
||||
//#define E0_SERIAL_TX_PIN PC3 // SERVO0_PIN -- XS1 - 5
|
||||
//#define X_SERIAL_RX_PIN X_SERIAL_TX_PIN
|
||||
//#define Y_SERIAL_RX_PIN Y_SERIAL_TX_PIN
|
||||
//#define Z_SERIAL_RX_PIN Z_SERIAL_TX_PIN
|
||||
//#define E0_SERIAL_RX_PIN E0_SERIAL_TX_PIN
|
||||
//#define TMC_HARDWARE_SERIAL
|
||||
#if ENABLED(TMC_HARDWARE_SERIAL)
|
||||
#define X_HARDWARE_SERIAL MSerial0
|
||||
#define X2_HARDWARE_SERIAL MSerial0
|
||||
#define Y_HARDWARE_SERIAL MSerial0
|
||||
#define Y2_HARDWARE_SERIAL MSerial0
|
||||
#define Z_HARDWARE_SERIAL MSerial0
|
||||
#define Z2_HARDWARE_SERIAL MSerial0
|
||||
#define E0_HARDWARE_SERIAL MSerial0
|
||||
#define E1_HARDWARE_SERIAL MSerial0
|
||||
#endif
|
||||
|
||||
// Reduce baud rate for software serial reliability
|
||||
#if HAS_TMC_SW_SERIAL
|
||||
//#define TMC_SOFTWARE_SERIAL
|
||||
#if ENABLED(TMC_SOFTWARE_SERIAL)
|
||||
#define X_SERIAL_TX_PIN PF8 // SERVO3_PIN -- XS2 - 6
|
||||
#define Y_SERIAL_TX_PIN PF9 // SERVO2_PIN -- XS2 - 5
|
||||
#define Z_SERIAL_TX_PIN PA1 // SERVO1_PIN -- XS1 - 6
|
||||
#define E0_SERIAL_TX_PIN PC3 // SERVO0_PIN -- XS1 - 5
|
||||
#define X_SERIAL_RX_PIN X_SERIAL_TX_PIN
|
||||
#define Y_SERIAL_RX_PIN Y_SERIAL_TX_PIN
|
||||
#define Z_SERIAL_RX_PIN Z_SERIAL_TX_PIN
|
||||
#define E0_SERIAL_RX_PIN E0_SERIAL_TX_PIN
|
||||
#define TMC_BAUD_RATE 19200
|
||||
#endif
|
||||
#endif
|
||||
|
||||
//
|
||||
// W25Q64 64Mb (8MB) SPI flash
|
||||
//
|
||||
#define HAS_SPI_FLASH 1
|
||||
#if HAS_SPI_FLASH
|
||||
#define SPI_FLASH_SIZE 0x800000 // 8MB
|
||||
#define W25QXX_CS_PIN PG9
|
||||
#define W25QXX_MOSI_PIN PB15
|
||||
#define W25QXX_MISO_PIN PB14
|
||||
#define W25QXX_SCK_PIN PB13
|
||||
#endif
|
||||
|
|
|
|||
Loading…
Reference in a new issue