Merge pull request #7919 from thinkyhead/bf2_neopixel_full
[2.0.x] Different NEOPIXEL types
This commit is contained in:
commit
10124f39d9
|
@ -1588,14 +1588,20 @@
|
||||||
* Adds the M150 command to set the LED (or LED strip) color.
|
* Adds the M150 command to set the LED (or LED strip) color.
|
||||||
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
||||||
* luminance values can be set from 0 to 255.
|
* luminance values can be set from 0 to 255.
|
||||||
|
* For Neopixel LED overall brightness parameters is also available
|
||||||
*
|
*
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
||||||
* as the Arduino cannot handle the current the LEDs will require.
|
* as the Arduino cannot handle the current the LEDs will require.
|
||||||
* Failure to follow this precaution can destroy your Arduino!
|
* Failure to follow this precaution can destroy your Arduino!
|
||||||
|
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino
|
||||||
|
* cannot handle the current, separate 5V power supply must be used
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
*
|
*
|
||||||
|
* LED type. This options are mutualy exclusive. Uncomment only one.
|
||||||
|
*
|
||||||
*/
|
*/
|
||||||
|
|
||||||
//#define RGB_LED
|
//#define RGB_LED
|
||||||
//#define RGBW_LED
|
//#define RGBW_LED
|
||||||
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
||||||
|
@ -1606,11 +1612,14 @@
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
// Support for Adafruit Neopixel LED driver
|
// Support for Adafruit Neopixel LED driver
|
||||||
//#define NEOPIXEL_RGBW_LED
|
//#define NEOPIXEL_LED
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(NEOPIXEL_LED)
|
||||||
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
|
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
|
||||||
#define NEOPIXEL_PIXELS 3
|
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
|
||||||
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
|
||||||
|
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
|
||||||
|
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
|
||||||
|
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
@ -1624,7 +1633,7 @@
|
||||||
* - Change to green once print has finished
|
* - Change to green once print has finished
|
||||||
* - Turn off after the print has finished and the user has pushed a button
|
* - Turn off after the print has finished and the user has pushed a button
|
||||||
*/
|
*/
|
||||||
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
|
||||||
#define PRINTER_EVENT_LEDS
|
#define PRINTER_EVENT_LEDS
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -796,7 +796,7 @@ void setup() {
|
||||||
OUT_WRITE(STAT_LED_BLUE_PIN, LOW); // turn it off
|
OUT_WRITE(STAT_LED_BLUE_PIN, LOW); // turn it off
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(NEOPIXEL_LED)
|
||||||
SET_OUTPUT(NEOPIXEL_PIN);
|
SET_OUTPUT(NEOPIXEL_PIN);
|
||||||
setup_neopixel();
|
setup_neopixel();
|
||||||
#endif
|
#endif
|
||||||
|
|
|
@ -1588,14 +1588,20 @@
|
||||||
* Adds the M150 command to set the LED (or LED strip) color.
|
* Adds the M150 command to set the LED (or LED strip) color.
|
||||||
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
||||||
* luminance values can be set from 0 to 255.
|
* luminance values can be set from 0 to 255.
|
||||||
|
* For Neopixel LED overall brightness parameters is also available
|
||||||
*
|
*
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
||||||
* as the Arduino cannot handle the current the LEDs will require.
|
* as the Arduino cannot handle the current the LEDs will require.
|
||||||
* Failure to follow this precaution can destroy your Arduino!
|
* Failure to follow this precaution can destroy your Arduino!
|
||||||
|
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino
|
||||||
|
* cannot handle the current, separate 5V power supply must be used
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
*
|
*
|
||||||
|
* LED type. This options are mutualy exclusive. Uncomment only one.
|
||||||
|
*
|
||||||
*/
|
*/
|
||||||
|
|
||||||
//#define RGB_LED
|
//#define RGB_LED
|
||||||
//#define RGBW_LED
|
//#define RGBW_LED
|
||||||
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
||||||
|
@ -1606,11 +1612,14 @@
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
// Support for Adafruit Neopixel LED driver
|
// Support for Adafruit Neopixel LED driver
|
||||||
//#define NEOPIXEL_RGBW_LED
|
//#define NEOPIXEL_LED
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(NEOPIXEL_LED)
|
||||||
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
|
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
|
||||||
#define NEOPIXEL_PIXELS 3
|
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
|
||||||
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
|
||||||
|
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
|
||||||
|
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
|
||||||
|
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
@ -1624,7 +1633,7 @@
|
||||||
* - Change to green once print has finished
|
* - Change to green once print has finished
|
||||||
* - Turn off after the print has finished and the user has pushed a button
|
* - Turn off after the print has finished and the user has pushed a button
|
||||||
*/
|
*/
|
||||||
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
|
||||||
#define PRINTER_EVENT_LEDS
|
#define PRINTER_EVENT_LEDS
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -1608,14 +1608,20 @@
|
||||||
* Adds the M150 command to set the LED (or LED strip) color.
|
* Adds the M150 command to set the LED (or LED strip) color.
|
||||||
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
||||||
* luminance values can be set from 0 to 255.
|
* luminance values can be set from 0 to 255.
|
||||||
|
* For Neopixel LED overall brightness parameters is also available
|
||||||
*
|
*
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
||||||
* as the Arduino cannot handle the current the LEDs will require.
|
* as the Arduino cannot handle the current the LEDs will require.
|
||||||
* Failure to follow this precaution can destroy your Arduino!
|
* Failure to follow this precaution can destroy your Arduino!
|
||||||
|
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino
|
||||||
|
* cannot handle the current, separate 5V power supply must be used
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
*
|
*
|
||||||
|
* LED type. This options are mutualy exclusive. Uncomment only one.
|
||||||
|
*
|
||||||
*/
|
*/
|
||||||
|
|
||||||
//#define RGB_LED
|
//#define RGB_LED
|
||||||
//#define RGBW_LED
|
//#define RGBW_LED
|
||||||
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
||||||
|
@ -1626,11 +1632,14 @@
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
// Support for Adafruit Neopixel LED driver
|
// Support for Adafruit Neopixel LED driver
|
||||||
//#define NEOPIXEL_RGBW_LED
|
//#define NEOPIXEL_LED
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(NEOPIXEL_LED)
|
||||||
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
|
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
|
||||||
#define NEOPIXEL_PIXELS 3
|
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
|
||||||
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
|
||||||
|
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
|
||||||
|
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
|
||||||
|
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
@ -1644,7 +1653,7 @@
|
||||||
* - Change to green once print has finished
|
* - Change to green once print has finished
|
||||||
* - Turn off after the print has finished and the user has pushed a button
|
* - Turn off after the print has finished and the user has pushed a button
|
||||||
*/
|
*/
|
||||||
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
|
||||||
#define PRINTER_EVENT_LEDS
|
#define PRINTER_EVENT_LEDS
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -1588,14 +1588,20 @@
|
||||||
* Adds the M150 command to set the LED (or LED strip) color.
|
* Adds the M150 command to set the LED (or LED strip) color.
|
||||||
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
||||||
* luminance values can be set from 0 to 255.
|
* luminance values can be set from 0 to 255.
|
||||||
|
* For Neopixel LED overall brightness parameters is also available
|
||||||
*
|
*
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
||||||
* as the Arduino cannot handle the current the LEDs will require.
|
* as the Arduino cannot handle the current the LEDs will require.
|
||||||
* Failure to follow this precaution can destroy your Arduino!
|
* Failure to follow this precaution can destroy your Arduino!
|
||||||
|
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino
|
||||||
|
* cannot handle the current, separate 5V power supply must be used
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
*
|
*
|
||||||
|
* LED type. This options are mutualy exclusive. Uncomment only one.
|
||||||
|
*
|
||||||
*/
|
*/
|
||||||
|
|
||||||
//#define RGB_LED
|
//#define RGB_LED
|
||||||
//#define RGBW_LED
|
//#define RGBW_LED
|
||||||
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
||||||
|
@ -1606,11 +1612,14 @@
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
// Support for Adafruit Neopixel LED driver
|
// Support for Adafruit Neopixel LED driver
|
||||||
//#define NEOPIXEL_RGBW_LED
|
//#define NEOPIXEL_LED
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(NEOPIXEL_LED)
|
||||||
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
|
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
|
||||||
#define NEOPIXEL_PIXELS 3
|
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
|
||||||
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
|
||||||
|
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
|
||||||
|
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
|
||||||
|
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
@ -1624,7 +1633,7 @@
|
||||||
* - Change to green once print has finished
|
* - Change to green once print has finished
|
||||||
* - Turn off after the print has finished and the user has pushed a button
|
* - Turn off after the print has finished and the user has pushed a button
|
||||||
*/
|
*/
|
||||||
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
|
||||||
#define PRINTER_EVENT_LEDS
|
#define PRINTER_EVENT_LEDS
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -1747,14 +1747,20 @@
|
||||||
* Adds the M150 command to set the LED (or LED strip) color.
|
* Adds the M150 command to set the LED (or LED strip) color.
|
||||||
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
||||||
* luminance values can be set from 0 to 255.
|
* luminance values can be set from 0 to 255.
|
||||||
|
* For Neopixel LED overall brightness parameters is also available
|
||||||
*
|
*
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
||||||
* as the Arduino cannot handle the current the LEDs will require.
|
* as the Arduino cannot handle the current the LEDs will require.
|
||||||
* Failure to follow this precaution can destroy your Arduino!
|
* Failure to follow this precaution can destroy your Arduino!
|
||||||
|
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino
|
||||||
|
* cannot handle the current, separate 5V power supply must be used
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
*
|
*
|
||||||
|
* LED type. This options are mutualy exclusive. Uncomment only one.
|
||||||
|
*
|
||||||
*/
|
*/
|
||||||
|
|
||||||
//#define RGB_LED
|
//#define RGB_LED
|
||||||
//#define RGBW_LED
|
//#define RGBW_LED
|
||||||
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
||||||
|
@ -1765,11 +1771,14 @@
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
// Support for Adafruit Neopixel LED driver
|
// Support for Adafruit Neopixel LED driver
|
||||||
//#define NEOPIXEL_RGBW_LED
|
//#define NEOPIXEL_LED
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(NEOPIXEL_LED)
|
||||||
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
|
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
|
||||||
#define NEOPIXEL_PIXELS 3
|
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
|
||||||
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
|
||||||
|
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
|
||||||
|
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
|
||||||
|
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
@ -1783,7 +1792,7 @@
|
||||||
* - Change to green once print has finished
|
* - Change to green once print has finished
|
||||||
* - Turn off after the print has finished and the user has pushed a button
|
* - Turn off after the print has finished and the user has pushed a button
|
||||||
*/
|
*/
|
||||||
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
|
||||||
#define PRINTER_EVENT_LEDS
|
#define PRINTER_EVENT_LEDS
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -1596,14 +1596,20 @@
|
||||||
* Adds the M150 command to set the LED (or LED strip) color.
|
* Adds the M150 command to set the LED (or LED strip) color.
|
||||||
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
||||||
* luminance values can be set from 0 to 255.
|
* luminance values can be set from 0 to 255.
|
||||||
|
* For Neopixel LED overall brightness parameters is also available
|
||||||
*
|
*
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
||||||
* as the Arduino cannot handle the current the LEDs will require.
|
* as the Arduino cannot handle the current the LEDs will require.
|
||||||
* Failure to follow this precaution can destroy your Arduino!
|
* Failure to follow this precaution can destroy your Arduino!
|
||||||
|
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino
|
||||||
|
* cannot handle the current, separate 5V power supply must be used
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
*
|
*
|
||||||
|
* LED type. This options are mutualy exclusive. Uncomment only one.
|
||||||
|
*
|
||||||
*/
|
*/
|
||||||
|
|
||||||
//#define RGB_LED
|
//#define RGB_LED
|
||||||
//#define RGBW_LED
|
//#define RGBW_LED
|
||||||
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
||||||
|
@ -1614,11 +1620,14 @@
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
// Support for Adafruit Neopixel LED driver
|
// Support for Adafruit Neopixel LED driver
|
||||||
//#define NEOPIXEL_RGBW_LED
|
//#define NEOPIXEL_LED
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(NEOPIXEL_LED)
|
||||||
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
|
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
|
||||||
#define NEOPIXEL_PIXELS 3
|
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
|
||||||
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
|
||||||
|
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
|
||||||
|
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
|
||||||
|
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
@ -1632,7 +1641,7 @@
|
||||||
* - Change to green once print has finished
|
* - Change to green once print has finished
|
||||||
* - Turn off after the print has finished and the user has pushed a button
|
* - Turn off after the print has finished and the user has pushed a button
|
||||||
*/
|
*/
|
||||||
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
|
||||||
#define PRINTER_EVENT_LEDS
|
#define PRINTER_EVENT_LEDS
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -1579,14 +1579,20 @@
|
||||||
* Adds the M150 command to set the LED (or LED strip) color.
|
* Adds the M150 command to set the LED (or LED strip) color.
|
||||||
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
||||||
* luminance values can be set from 0 to 255.
|
* luminance values can be set from 0 to 255.
|
||||||
|
* For Neopixel LED overall brightness parameters is also available
|
||||||
*
|
*
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
||||||
* as the Arduino cannot handle the current the LEDs will require.
|
* as the Arduino cannot handle the current the LEDs will require.
|
||||||
* Failure to follow this precaution can destroy your Arduino!
|
* Failure to follow this precaution can destroy your Arduino!
|
||||||
|
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino
|
||||||
|
* cannot handle the current, separate 5V power supply must be used
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
*
|
*
|
||||||
|
* LED type. This options are mutualy exclusive. Uncomment only one.
|
||||||
|
*
|
||||||
*/
|
*/
|
||||||
|
|
||||||
//#define RGB_LED
|
//#define RGB_LED
|
||||||
//#define RGBW_LED
|
//#define RGBW_LED
|
||||||
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
||||||
|
@ -1597,11 +1603,14 @@
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
// Support for Adafruit Neopixel LED driver
|
// Support for Adafruit Neopixel LED driver
|
||||||
//#define NEOPIXEL_RGBW_LED
|
//#define NEOPIXEL_LED
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(NEOPIXEL_LED)
|
||||||
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
|
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
|
||||||
#define NEOPIXEL_PIXELS 3
|
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
|
||||||
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
|
||||||
|
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
|
||||||
|
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
|
||||||
|
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
@ -1615,7 +1624,7 @@
|
||||||
* - Change to green once print has finished
|
* - Change to green once print has finished
|
||||||
* - Turn off after the print has finished and the user has pushed a button
|
* - Turn off after the print has finished and the user has pushed a button
|
||||||
*/
|
*/
|
||||||
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
|
||||||
#define PRINTER_EVENT_LEDS
|
#define PRINTER_EVENT_LEDS
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -1589,14 +1589,20 @@
|
||||||
* Adds the M150 command to set the LED (or LED strip) color.
|
* Adds the M150 command to set the LED (or LED strip) color.
|
||||||
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
||||||
* luminance values can be set from 0 to 255.
|
* luminance values can be set from 0 to 255.
|
||||||
|
* For Neopixel LED overall brightness parameters is also available
|
||||||
*
|
*
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
||||||
* as the Arduino cannot handle the current the LEDs will require.
|
* as the Arduino cannot handle the current the LEDs will require.
|
||||||
* Failure to follow this precaution can destroy your Arduino!
|
* Failure to follow this precaution can destroy your Arduino!
|
||||||
|
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino
|
||||||
|
* cannot handle the current, separate 5V power supply must be used
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
*
|
*
|
||||||
|
* LED type. This options are mutualy exclusive. Uncomment only one.
|
||||||
|
*
|
||||||
*/
|
*/
|
||||||
|
|
||||||
//#define RGB_LED
|
//#define RGB_LED
|
||||||
//#define RGBW_LED
|
//#define RGBW_LED
|
||||||
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
||||||
|
@ -1607,11 +1613,14 @@
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
// Support for Adafruit Neopixel LED driver
|
// Support for Adafruit Neopixel LED driver
|
||||||
//#define NEOPIXEL_RGBW_LED
|
//#define NEOPIXEL_LED
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(NEOPIXEL_LED)
|
||||||
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
|
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
|
||||||
#define NEOPIXEL_PIXELS 3
|
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
|
||||||
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
|
||||||
|
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
|
||||||
|
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
|
||||||
|
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
@ -1625,7 +1634,7 @@
|
||||||
* - Change to green once print has finished
|
* - Change to green once print has finished
|
||||||
* - Turn off after the print has finished and the user has pushed a button
|
* - Turn off after the print has finished and the user has pushed a button
|
||||||
*/
|
*/
|
||||||
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
|
||||||
#define PRINTER_EVENT_LEDS
|
#define PRINTER_EVENT_LEDS
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -1579,14 +1579,20 @@
|
||||||
* Adds the M150 command to set the LED (or LED strip) color.
|
* Adds the M150 command to set the LED (or LED strip) color.
|
||||||
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
||||||
* luminance values can be set from 0 to 255.
|
* luminance values can be set from 0 to 255.
|
||||||
|
* For Neopixel LED overall brightness parameters is also available
|
||||||
*
|
*
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
||||||
* as the Arduino cannot handle the current the LEDs will require.
|
* as the Arduino cannot handle the current the LEDs will require.
|
||||||
* Failure to follow this precaution can destroy your Arduino!
|
* Failure to follow this precaution can destroy your Arduino!
|
||||||
|
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino
|
||||||
|
* cannot handle the current, separate 5V power supply must be used
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
*
|
*
|
||||||
|
* LED type. This options are mutualy exclusive. Uncomment only one.
|
||||||
|
*
|
||||||
*/
|
*/
|
||||||
|
|
||||||
//#define RGB_LED
|
//#define RGB_LED
|
||||||
//#define RGBW_LED
|
//#define RGBW_LED
|
||||||
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
||||||
|
@ -1597,11 +1603,14 @@
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
// Support for Adafruit Neopixel LED driver
|
// Support for Adafruit Neopixel LED driver
|
||||||
//#define NEOPIXEL_RGBW_LED
|
//#define NEOPIXEL_LED
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(NEOPIXEL_LED)
|
||||||
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
|
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
|
||||||
#define NEOPIXEL_PIXELS 3
|
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
|
||||||
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
|
||||||
|
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
|
||||||
|
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
|
||||||
|
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
@ -1615,7 +1624,7 @@
|
||||||
* - Change to green once print has finished
|
* - Change to green once print has finished
|
||||||
* - Turn off after the print has finished and the user has pushed a button
|
* - Turn off after the print has finished and the user has pushed a button
|
||||||
*/
|
*/
|
||||||
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
|
||||||
#define PRINTER_EVENT_LEDS
|
#define PRINTER_EVENT_LEDS
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -1587,14 +1587,20 @@
|
||||||
* Adds the M150 command to set the LED (or LED strip) color.
|
* Adds the M150 command to set the LED (or LED strip) color.
|
||||||
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
||||||
* luminance values can be set from 0 to 255.
|
* luminance values can be set from 0 to 255.
|
||||||
|
* For Neopixel LED overall brightness parameters is also available
|
||||||
*
|
*
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
||||||
* as the Arduino cannot handle the current the LEDs will require.
|
* as the Arduino cannot handle the current the LEDs will require.
|
||||||
* Failure to follow this precaution can destroy your Arduino!
|
* Failure to follow this precaution can destroy your Arduino!
|
||||||
|
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino
|
||||||
|
* cannot handle the current, separate 5V power supply must be used
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
*
|
*
|
||||||
|
* LED type. This options are mutualy exclusive. Uncomment only one.
|
||||||
|
*
|
||||||
*/
|
*/
|
||||||
|
|
||||||
//#define RGB_LED
|
//#define RGB_LED
|
||||||
//#define RGBW_LED
|
//#define RGBW_LED
|
||||||
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
||||||
|
@ -1605,11 +1611,14 @@
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
// Support for Adafruit Neopixel LED driver
|
// Support for Adafruit Neopixel LED driver
|
||||||
//#define NEOPIXEL_RGBW_LED
|
//#define NEOPIXEL_LED
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(NEOPIXEL_LED)
|
||||||
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
|
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
|
||||||
#define NEOPIXEL_PIXELS 3
|
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
|
||||||
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
|
||||||
|
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
|
||||||
|
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
|
||||||
|
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
@ -1623,7 +1632,7 @@
|
||||||
* - Change to green once print has finished
|
* - Change to green once print has finished
|
||||||
* - Turn off after the print has finished and the user has pushed a button
|
* - Turn off after the print has finished and the user has pushed a button
|
||||||
*/
|
*/
|
||||||
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
|
||||||
#define PRINTER_EVENT_LEDS
|
#define PRINTER_EVENT_LEDS
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -1598,14 +1598,20 @@
|
||||||
* Adds the M150 command to set the LED (or LED strip) color.
|
* Adds the M150 command to set the LED (or LED strip) color.
|
||||||
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
||||||
* luminance values can be set from 0 to 255.
|
* luminance values can be set from 0 to 255.
|
||||||
|
* For Neopixel LED overall brightness parameters is also available
|
||||||
*
|
*
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
||||||
* as the Arduino cannot handle the current the LEDs will require.
|
* as the Arduino cannot handle the current the LEDs will require.
|
||||||
* Failure to follow this precaution can destroy your Arduino!
|
* Failure to follow this precaution can destroy your Arduino!
|
||||||
|
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino
|
||||||
|
* cannot handle the current, separate 5V power supply must be used
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
*
|
*
|
||||||
|
* LED type. This options are mutualy exclusive. Uncomment only one.
|
||||||
|
*
|
||||||
*/
|
*/
|
||||||
|
|
||||||
//#define RGB_LED
|
//#define RGB_LED
|
||||||
//#define RGBW_LED
|
//#define RGBW_LED
|
||||||
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
||||||
|
@ -1616,11 +1622,14 @@
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
// Support for Adafruit Neopixel LED driver
|
// Support for Adafruit Neopixel LED driver
|
||||||
//#define NEOPIXEL_RGBW_LED
|
//#define NEOPIXEL_LED
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(NEOPIXEL_LED)
|
||||||
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
|
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
|
||||||
#define NEOPIXEL_PIXELS 3
|
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
|
||||||
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
|
||||||
|
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
|
||||||
|
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
|
||||||
|
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
@ -1634,7 +1643,7 @@
|
||||||
* - Change to green once print has finished
|
* - Change to green once print has finished
|
||||||
* - Turn off after the print has finished and the user has pushed a button
|
* - Turn off after the print has finished and the user has pushed a button
|
||||||
*/
|
*/
|
||||||
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
|
||||||
#define PRINTER_EVENT_LEDS
|
#define PRINTER_EVENT_LEDS
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -1570,14 +1570,20 @@
|
||||||
* Adds the M150 command to set the LED (or LED strip) color.
|
* Adds the M150 command to set the LED (or LED strip) color.
|
||||||
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
||||||
* luminance values can be set from 0 to 255.
|
* luminance values can be set from 0 to 255.
|
||||||
|
* For Neopixel LED overall brightness parameters is also available
|
||||||
*
|
*
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
||||||
* as the Arduino cannot handle the current the LEDs will require.
|
* as the Arduino cannot handle the current the LEDs will require.
|
||||||
* Failure to follow this precaution can destroy your Arduino!
|
* Failure to follow this precaution can destroy your Arduino!
|
||||||
|
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino
|
||||||
|
* cannot handle the current, separate 5V power supply must be used
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
*
|
*
|
||||||
|
* LED type. This options are mutualy exclusive. Uncomment only one.
|
||||||
|
*
|
||||||
*/
|
*/
|
||||||
|
|
||||||
//#define RGB_LED
|
//#define RGB_LED
|
||||||
//#define RGBW_LED
|
//#define RGBW_LED
|
||||||
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
||||||
|
@ -1588,11 +1594,14 @@
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
// Support for Adafruit Neopixel LED driver
|
// Support for Adafruit Neopixel LED driver
|
||||||
//#define NEOPIXEL_RGBW_LED
|
//#define NEOPIXEL_LED
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(NEOPIXEL_LED)
|
||||||
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
|
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
|
||||||
#define NEOPIXEL_PIXELS 3
|
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
|
||||||
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
|
||||||
|
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
|
||||||
|
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
|
||||||
|
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
@ -1606,7 +1615,7 @@
|
||||||
* - Change to green once print has finished
|
* - Change to green once print has finished
|
||||||
* - Turn off after the print has finished and the user has pushed a button
|
* - Turn off after the print has finished and the user has pushed a button
|
||||||
*/
|
*/
|
||||||
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
|
||||||
#define PRINTER_EVENT_LEDS
|
#define PRINTER_EVENT_LEDS
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -1570,14 +1570,20 @@
|
||||||
* Adds the M150 command to set the LED (or LED strip) color.
|
* Adds the M150 command to set the LED (or LED strip) color.
|
||||||
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
||||||
* luminance values can be set from 0 to 255.
|
* luminance values can be set from 0 to 255.
|
||||||
|
* For Neopixel LED overall brightness parameters is also available
|
||||||
*
|
*
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
||||||
* as the Arduino cannot handle the current the LEDs will require.
|
* as the Arduino cannot handle the current the LEDs will require.
|
||||||
* Failure to follow this precaution can destroy your Arduino!
|
* Failure to follow this precaution can destroy your Arduino!
|
||||||
|
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino
|
||||||
|
* cannot handle the current, separate 5V power supply must be used
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
*
|
*
|
||||||
|
* LED type. This options are mutualy exclusive. Uncomment only one.
|
||||||
|
*
|
||||||
*/
|
*/
|
||||||
|
|
||||||
//#define RGB_LED
|
//#define RGB_LED
|
||||||
//#define RGBW_LED
|
//#define RGBW_LED
|
||||||
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
||||||
|
@ -1588,11 +1594,14 @@
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
// Support for Adafruit Neopixel LED driver
|
// Support for Adafruit Neopixel LED driver
|
||||||
//#define NEOPIXEL_RGBW_LED
|
//#define NEOPIXEL_LED
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(NEOPIXEL_LED)
|
||||||
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
|
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
|
||||||
#define NEOPIXEL_PIXELS 3
|
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
|
||||||
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
|
||||||
|
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
|
||||||
|
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
|
||||||
|
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
@ -1606,7 +1615,7 @@
|
||||||
* - Change to green once print has finished
|
* - Change to green once print has finished
|
||||||
* - Turn off after the print has finished and the user has pushed a button
|
* - Turn off after the print has finished and the user has pushed a button
|
||||||
*/
|
*/
|
||||||
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
|
||||||
#define PRINTER_EVENT_LEDS
|
#define PRINTER_EVENT_LEDS
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -1593,14 +1593,20 @@
|
||||||
* Adds the M150 command to set the LED (or LED strip) color.
|
* Adds the M150 command to set the LED (or LED strip) color.
|
||||||
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
||||||
* luminance values can be set from 0 to 255.
|
* luminance values can be set from 0 to 255.
|
||||||
|
* For Neopixel LED overall brightness parameters is also available
|
||||||
*
|
*
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
||||||
* as the Arduino cannot handle the current the LEDs will require.
|
* as the Arduino cannot handle the current the LEDs will require.
|
||||||
* Failure to follow this precaution can destroy your Arduino!
|
* Failure to follow this precaution can destroy your Arduino!
|
||||||
|
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino
|
||||||
|
* cannot handle the current, separate 5V power supply must be used
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
*
|
*
|
||||||
|
* LED type. This options are mutualy exclusive. Uncomment only one.
|
||||||
|
*
|
||||||
*/
|
*/
|
||||||
|
|
||||||
//#define RGB_LED
|
//#define RGB_LED
|
||||||
//#define RGBW_LED
|
//#define RGBW_LED
|
||||||
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
||||||
|
@ -1611,11 +1617,14 @@
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
// Support for Adafruit Neopixel LED driver
|
// Support for Adafruit Neopixel LED driver
|
||||||
//#define NEOPIXEL_RGBW_LED
|
//#define NEOPIXEL_LED
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(NEOPIXEL_LED)
|
||||||
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
|
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
|
||||||
#define NEOPIXEL_PIXELS 3
|
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
|
||||||
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
|
||||||
|
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
|
||||||
|
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
|
||||||
|
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
@ -1629,7 +1638,7 @@
|
||||||
* - Change to green once print has finished
|
* - Change to green once print has finished
|
||||||
* - Turn off after the print has finished and the user has pushed a button
|
* - Turn off after the print has finished and the user has pushed a button
|
||||||
*/
|
*/
|
||||||
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
|
||||||
#define PRINTER_EVENT_LEDS
|
#define PRINTER_EVENT_LEDS
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -1603,14 +1603,20 @@
|
||||||
* Adds the M150 command to set the LED (or LED strip) color.
|
* Adds the M150 command to set the LED (or LED strip) color.
|
||||||
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
||||||
* luminance values can be set from 0 to 255.
|
* luminance values can be set from 0 to 255.
|
||||||
|
* For Neopixel LED overall brightness parameters is also available
|
||||||
*
|
*
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
||||||
* as the Arduino cannot handle the current the LEDs will require.
|
* as the Arduino cannot handle the current the LEDs will require.
|
||||||
* Failure to follow this precaution can destroy your Arduino!
|
* Failure to follow this precaution can destroy your Arduino!
|
||||||
|
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino
|
||||||
|
* cannot handle the current, separate 5V power supply must be used
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
*
|
*
|
||||||
|
* LED type. This options are mutualy exclusive. Uncomment only one.
|
||||||
|
*
|
||||||
*/
|
*/
|
||||||
|
|
||||||
//#define RGB_LED
|
//#define RGB_LED
|
||||||
//#define RGBW_LED
|
//#define RGBW_LED
|
||||||
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
||||||
|
@ -1621,11 +1627,14 @@
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
// Support for Adafruit Neopixel LED driver
|
// Support for Adafruit Neopixel LED driver
|
||||||
//#define NEOPIXEL_RGBW_LED
|
//#define NEOPIXEL_LED
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(NEOPIXEL_LED)
|
||||||
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
|
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
|
||||||
#define NEOPIXEL_PIXELS 3
|
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
|
||||||
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
|
||||||
|
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
|
||||||
|
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
|
||||||
|
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
@ -1639,7 +1648,7 @@
|
||||||
* - Change to green once print has finished
|
* - Change to green once print has finished
|
||||||
* - Turn off after the print has finished and the user has pushed a button
|
* - Turn off after the print has finished and the user has pushed a button
|
||||||
*/
|
*/
|
||||||
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
|
||||||
#define PRINTER_EVENT_LEDS
|
#define PRINTER_EVENT_LEDS
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -1588,14 +1588,20 @@
|
||||||
* Adds the M150 command to set the LED (or LED strip) color.
|
* Adds the M150 command to set the LED (or LED strip) color.
|
||||||
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
||||||
* luminance values can be set from 0 to 255.
|
* luminance values can be set from 0 to 255.
|
||||||
|
* For Neopixel LED overall brightness parameters is also available
|
||||||
*
|
*
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
||||||
* as the Arduino cannot handle the current the LEDs will require.
|
* as the Arduino cannot handle the current the LEDs will require.
|
||||||
* Failure to follow this precaution can destroy your Arduino!
|
* Failure to follow this precaution can destroy your Arduino!
|
||||||
|
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino
|
||||||
|
* cannot handle the current, separate 5V power supply must be used
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
*
|
*
|
||||||
|
* LED type. This options are mutualy exclusive. Uncomment only one.
|
||||||
|
*
|
||||||
*/
|
*/
|
||||||
|
|
||||||
//#define RGB_LED
|
//#define RGB_LED
|
||||||
//#define RGBW_LED
|
//#define RGBW_LED
|
||||||
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
||||||
|
@ -1606,11 +1612,14 @@
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
// Support for Adafruit Neopixel LED driver
|
// Support for Adafruit Neopixel LED driver
|
||||||
//#define NEOPIXEL_RGBW_LED
|
//#define NEOPIXEL_LED
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(NEOPIXEL_LED)
|
||||||
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
|
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
|
||||||
#define NEOPIXEL_PIXELS 3
|
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
|
||||||
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
|
||||||
|
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
|
||||||
|
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
|
||||||
|
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
@ -1624,7 +1633,7 @@
|
||||||
* - Change to green once print has finished
|
* - Change to green once print has finished
|
||||||
* - Turn off after the print has finished and the user has pushed a button
|
* - Turn off after the print has finished and the user has pushed a button
|
||||||
*/
|
*/
|
||||||
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
|
||||||
#define PRINTER_EVENT_LEDS
|
#define PRINTER_EVENT_LEDS
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -1592,14 +1592,20 @@
|
||||||
* Adds the M150 command to set the LED (or LED strip) color.
|
* Adds the M150 command to set the LED (or LED strip) color.
|
||||||
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
||||||
* luminance values can be set from 0 to 255.
|
* luminance values can be set from 0 to 255.
|
||||||
|
* For Neopixel LED overall brightness parameters is also available
|
||||||
*
|
*
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
||||||
* as the Arduino cannot handle the current the LEDs will require.
|
* as the Arduino cannot handle the current the LEDs will require.
|
||||||
* Failure to follow this precaution can destroy your Arduino!
|
* Failure to follow this precaution can destroy your Arduino!
|
||||||
|
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino
|
||||||
|
* cannot handle the current, separate 5V power supply must be used
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
*
|
*
|
||||||
|
* LED type. This options are mutualy exclusive. Uncomment only one.
|
||||||
|
*
|
||||||
*/
|
*/
|
||||||
|
|
||||||
//#define RGB_LED
|
//#define RGB_LED
|
||||||
//#define RGBW_LED
|
//#define RGBW_LED
|
||||||
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
||||||
|
@ -1610,11 +1616,14 @@
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
// Support for Adafruit Neopixel LED driver
|
// Support for Adafruit Neopixel LED driver
|
||||||
//#define NEOPIXEL_RGBW_LED
|
//#define NEOPIXEL_LED
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(NEOPIXEL_LED)
|
||||||
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
|
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
|
||||||
#define NEOPIXEL_PIXELS 3
|
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
|
||||||
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
|
||||||
|
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
|
||||||
|
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
|
||||||
|
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
@ -1628,7 +1637,7 @@
|
||||||
* - Change to green once print has finished
|
* - Change to green once print has finished
|
||||||
* - Turn off after the print has finished and the user has pushed a button
|
* - Turn off after the print has finished and the user has pushed a button
|
||||||
*/
|
*/
|
||||||
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
|
||||||
#define PRINTER_EVENT_LEDS
|
#define PRINTER_EVENT_LEDS
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -1616,14 +1616,20 @@
|
||||||
* Adds the M150 command to set the LED (or LED strip) color.
|
* Adds the M150 command to set the LED (or LED strip) color.
|
||||||
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
||||||
* luminance values can be set from 0 to 255.
|
* luminance values can be set from 0 to 255.
|
||||||
|
* For Neopixel LED overall brightness parameters is also available
|
||||||
*
|
*
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
||||||
* as the Arduino cannot handle the current the LEDs will require.
|
* as the Arduino cannot handle the current the LEDs will require.
|
||||||
* Failure to follow this precaution can destroy your Arduino!
|
* Failure to follow this precaution can destroy your Arduino!
|
||||||
|
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino
|
||||||
|
* cannot handle the current, separate 5V power supply must be used
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
*
|
*
|
||||||
|
* LED type. This options are mutualy exclusive. Uncomment only one.
|
||||||
|
*
|
||||||
*/
|
*/
|
||||||
|
|
||||||
//#define RGB_LED
|
//#define RGB_LED
|
||||||
//#define RGBW_LED
|
//#define RGBW_LED
|
||||||
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
||||||
|
@ -1634,11 +1640,14 @@
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
// Support for Adafruit Neopixel LED driver
|
// Support for Adafruit Neopixel LED driver
|
||||||
//#define NEOPIXEL_RGBW_LED
|
//#define NEOPIXEL_LED
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(NEOPIXEL_LED)
|
||||||
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
|
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
|
||||||
#define NEOPIXEL_PIXELS 3
|
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
|
||||||
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
|
||||||
|
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
|
||||||
|
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
|
||||||
|
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
@ -1652,7 +1661,7 @@
|
||||||
* - Change to green once print has finished
|
* - Change to green once print has finished
|
||||||
* - Turn off after the print has finished and the user has pushed a button
|
* - Turn off after the print has finished and the user has pushed a button
|
||||||
*/
|
*/
|
||||||
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
|
||||||
#define PRINTER_EVENT_LEDS
|
#define PRINTER_EVENT_LEDS
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -1588,14 +1588,20 @@
|
||||||
* Adds the M150 command to set the LED (or LED strip) color.
|
* Adds the M150 command to set the LED (or LED strip) color.
|
||||||
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
||||||
* luminance values can be set from 0 to 255.
|
* luminance values can be set from 0 to 255.
|
||||||
|
* For Neopixel LED overall brightness parameters is also available
|
||||||
*
|
*
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
||||||
* as the Arduino cannot handle the current the LEDs will require.
|
* as the Arduino cannot handle the current the LEDs will require.
|
||||||
* Failure to follow this precaution can destroy your Arduino!
|
* Failure to follow this precaution can destroy your Arduino!
|
||||||
|
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino
|
||||||
|
* cannot handle the current, separate 5V power supply must be used
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
*
|
*
|
||||||
|
* LED type. This options are mutualy exclusive. Uncomment only one.
|
||||||
|
*
|
||||||
*/
|
*/
|
||||||
|
|
||||||
//#define RGB_LED
|
//#define RGB_LED
|
||||||
//#define RGBW_LED
|
//#define RGBW_LED
|
||||||
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
||||||
|
@ -1606,11 +1612,14 @@
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
// Support for Adafruit Neopixel LED driver
|
// Support for Adafruit Neopixel LED driver
|
||||||
//#define NEOPIXEL_RGBW_LED
|
//#define NEOPIXEL_LED
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(NEOPIXEL_LED)
|
||||||
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
|
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
|
||||||
#define NEOPIXEL_PIXELS 3
|
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
|
||||||
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
|
||||||
|
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
|
||||||
|
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
|
||||||
|
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
@ -1624,7 +1633,7 @@
|
||||||
* - Change to green once print has finished
|
* - Change to green once print has finished
|
||||||
* - Turn off after the print has finished and the user has pushed a button
|
* - Turn off after the print has finished and the user has pushed a button
|
||||||
*/
|
*/
|
||||||
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
|
||||||
#define PRINTER_EVENT_LEDS
|
#define PRINTER_EVENT_LEDS
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -1588,14 +1588,20 @@
|
||||||
* Adds the M150 command to set the LED (or LED strip) color.
|
* Adds the M150 command to set the LED (or LED strip) color.
|
||||||
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
||||||
* luminance values can be set from 0 to 255.
|
* luminance values can be set from 0 to 255.
|
||||||
|
* For Neopixel LED overall brightness parameters is also available
|
||||||
*
|
*
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
||||||
* as the Arduino cannot handle the current the LEDs will require.
|
* as the Arduino cannot handle the current the LEDs will require.
|
||||||
* Failure to follow this precaution can destroy your Arduino!
|
* Failure to follow this precaution can destroy your Arduino!
|
||||||
|
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino
|
||||||
|
* cannot handle the current, separate 5V power supply must be used
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
*
|
*
|
||||||
|
* LED type. This options are mutualy exclusive. Uncomment only one.
|
||||||
|
*
|
||||||
*/
|
*/
|
||||||
|
|
||||||
//#define RGB_LED
|
//#define RGB_LED
|
||||||
//#define RGBW_LED
|
//#define RGBW_LED
|
||||||
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
||||||
|
@ -1606,11 +1612,14 @@
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
// Support for Adafruit Neopixel LED driver
|
// Support for Adafruit Neopixel LED driver
|
||||||
//#define NEOPIXEL_RGBW_LED
|
//#define NEOPIXEL_LED
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(NEOPIXEL_LED)
|
||||||
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
|
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
|
||||||
#define NEOPIXEL_PIXELS 3
|
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
|
||||||
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
|
||||||
|
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
|
||||||
|
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
|
||||||
|
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
@ -1624,7 +1633,7 @@
|
||||||
* - Change to green once print has finished
|
* - Change to green once print has finished
|
||||||
* - Turn off after the print has finished and the user has pushed a button
|
* - Turn off after the print has finished and the user has pushed a button
|
||||||
*/
|
*/
|
||||||
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
|
||||||
#define PRINTER_EVENT_LEDS
|
#define PRINTER_EVENT_LEDS
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -1600,14 +1600,20 @@
|
||||||
* Adds the M150 command to set the LED (or LED strip) color.
|
* Adds the M150 command to set the LED (or LED strip) color.
|
||||||
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
||||||
* luminance values can be set from 0 to 255.
|
* luminance values can be set from 0 to 255.
|
||||||
|
* For Neopixel LED overall brightness parameters is also available
|
||||||
*
|
*
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
||||||
* as the Arduino cannot handle the current the LEDs will require.
|
* as the Arduino cannot handle the current the LEDs will require.
|
||||||
* Failure to follow this precaution can destroy your Arduino!
|
* Failure to follow this precaution can destroy your Arduino!
|
||||||
|
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino
|
||||||
|
* cannot handle the current, separate 5V power supply must be used
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
*
|
*
|
||||||
|
* LED type. This options are mutualy exclusive. Uncomment only one.
|
||||||
|
*
|
||||||
*/
|
*/
|
||||||
|
|
||||||
//#define RGB_LED
|
//#define RGB_LED
|
||||||
//#define RGBW_LED
|
//#define RGBW_LED
|
||||||
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
||||||
|
@ -1618,11 +1624,14 @@
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
// Support for Adafruit Neopixel LED driver
|
// Support for Adafruit Neopixel LED driver
|
||||||
//#define NEOPIXEL_RGBW_LED
|
//#define NEOPIXEL_LED
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(NEOPIXEL_LED)
|
||||||
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
|
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
|
||||||
#define NEOPIXEL_PIXELS 3
|
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
|
||||||
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
|
||||||
|
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
|
||||||
|
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
|
||||||
|
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
@ -1636,7 +1645,7 @@
|
||||||
* - Change to green once print has finished
|
* - Change to green once print has finished
|
||||||
* - Turn off after the print has finished and the user has pushed a button
|
* - Turn off after the print has finished and the user has pushed a button
|
||||||
*/
|
*/
|
||||||
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
|
||||||
#define PRINTER_EVENT_LEDS
|
#define PRINTER_EVENT_LEDS
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -1619,29 +1619,38 @@
|
||||||
* Adds the M150 command to set the LED (or LED strip) color.
|
* Adds the M150 command to set the LED (or LED strip) color.
|
||||||
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
||||||
* luminance values can be set from 0 to 255.
|
* luminance values can be set from 0 to 255.
|
||||||
|
* For Neopixel LED overall brightness parameters is also available
|
||||||
*
|
*
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
||||||
* as the Arduino cannot handle the current the LEDs will require.
|
* as the Arduino cannot handle the current the LEDs will require.
|
||||||
* Failure to follow this precaution can destroy your Arduino!
|
* Failure to follow this precaution can destroy your Arduino!
|
||||||
|
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino
|
||||||
|
* cannot handle the current, separate 5V power supply must be used
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
*
|
*
|
||||||
|
* LED type. This options are mutualy exclusive. Uncomment only one.
|
||||||
|
*
|
||||||
*/
|
*/
|
||||||
#define RGB_LED
|
|
||||||
|
//#define RGB_LED
|
||||||
//#define RGBW_LED
|
//#define RGBW_LED
|
||||||
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
||||||
#define RGB_LED_R_PIN 11
|
#define RGB_LED_R_PIN 34
|
||||||
#define RGB_LED_G_PIN 10
|
#define RGB_LED_G_PIN 43
|
||||||
#define RGB_LED_B_PIN 17
|
#define RGB_LED_B_PIN 35
|
||||||
#define RGB_LED_W_PIN -1
|
#define RGB_LED_W_PIN -1
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
// Support for Adafruit Neopixel LED driver
|
// Support for Adafruit Neopixel LED driver
|
||||||
//#define NEOPIXEL_RGBW_LED
|
//#define NEOPIXEL_LED
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(NEOPIXEL_LED)
|
||||||
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
|
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
|
||||||
#define NEOPIXEL_PIXELS 3
|
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
|
||||||
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
|
||||||
|
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
|
||||||
|
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
|
||||||
|
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
@ -1655,7 +1664,7 @@
|
||||||
* - Change to green once print has finished
|
* - Change to green once print has finished
|
||||||
* - Turn off after the print has finished and the user has pushed a button
|
* - Turn off after the print has finished and the user has pushed a button
|
||||||
*/
|
*/
|
||||||
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
|
||||||
#define PRINTER_EVENT_LEDS
|
#define PRINTER_EVENT_LEDS
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -1644,14 +1644,20 @@
|
||||||
* Adds the M150 command to set the LED (or LED strip) color.
|
* Adds the M150 command to set the LED (or LED strip) color.
|
||||||
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
||||||
* luminance values can be set from 0 to 255.
|
* luminance values can be set from 0 to 255.
|
||||||
|
* For Neopixel LED overall brightness parameters is also available
|
||||||
*
|
*
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
||||||
* as the Arduino cannot handle the current the LEDs will require.
|
* as the Arduino cannot handle the current the LEDs will require.
|
||||||
* Failure to follow this precaution can destroy your Arduino!
|
* Failure to follow this precaution can destroy your Arduino!
|
||||||
|
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino
|
||||||
|
* cannot handle the current, separate 5V power supply must be used
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
*
|
*
|
||||||
|
* LED type. This options are mutualy exclusive. Uncomment only one.
|
||||||
|
*
|
||||||
*/
|
*/
|
||||||
|
|
||||||
//#define RGB_LED
|
//#define RGB_LED
|
||||||
//#define RGBW_LED
|
//#define RGBW_LED
|
||||||
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
||||||
|
@ -1662,11 +1668,14 @@
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
// Support for Adafruit Neopixel LED driver
|
// Support for Adafruit Neopixel LED driver
|
||||||
//#define NEOPIXEL_RGBW_LED
|
//#define NEOPIXEL_LED
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(NEOPIXEL_LED)
|
||||||
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
|
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
|
||||||
#define NEOPIXEL_PIXELS 3
|
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
|
||||||
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
|
||||||
|
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
|
||||||
|
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
|
||||||
|
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
@ -1680,7 +1689,7 @@
|
||||||
* - Change to green once print has finished
|
* - Change to green once print has finished
|
||||||
* - Turn off after the print has finished and the user has pushed a button
|
* - Turn off after the print has finished and the user has pushed a button
|
||||||
*/
|
*/
|
||||||
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
|
||||||
#define PRINTER_EVENT_LEDS
|
#define PRINTER_EVENT_LEDS
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -1623,14 +1623,20 @@
|
||||||
* Adds the M150 command to set the LED (or LED strip) color.
|
* Adds the M150 command to set the LED (or LED strip) color.
|
||||||
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
||||||
* luminance values can be set from 0 to 255.
|
* luminance values can be set from 0 to 255.
|
||||||
|
* For Neopixel LED overall brightness parameters is also available
|
||||||
*
|
*
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
||||||
* as the Arduino cannot handle the current the LEDs will require.
|
* as the Arduino cannot handle the current the LEDs will require.
|
||||||
* Failure to follow this precaution can destroy your Arduino!
|
* Failure to follow this precaution can destroy your Arduino!
|
||||||
|
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino
|
||||||
|
* cannot handle the current, separate 5V power supply must be used
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
*
|
*
|
||||||
|
* LED type. This options are mutualy exclusive. Uncomment only one.
|
||||||
|
*
|
||||||
*/
|
*/
|
||||||
|
|
||||||
//#define RGB_LED
|
//#define RGB_LED
|
||||||
//#define RGBW_LED
|
//#define RGBW_LED
|
||||||
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
||||||
|
@ -1641,11 +1647,14 @@
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
// Support for Adafruit Neopixel LED driver
|
// Support for Adafruit Neopixel LED driver
|
||||||
//#define NEOPIXEL_RGBW_LED
|
//#define NEOPIXEL_LED
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(NEOPIXEL_LED)
|
||||||
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
|
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
|
||||||
#define NEOPIXEL_PIXELS 3
|
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
|
||||||
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
|
||||||
|
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
|
||||||
|
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
|
||||||
|
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
@ -1659,7 +1668,7 @@
|
||||||
* - Change to green once print has finished
|
* - Change to green once print has finished
|
||||||
* - Turn off after the print has finished and the user has pushed a button
|
* - Turn off after the print has finished and the user has pushed a button
|
||||||
*/
|
*/
|
||||||
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
|
||||||
#define PRINTER_EVENT_LEDS
|
#define PRINTER_EVENT_LEDS
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -1588,14 +1588,20 @@
|
||||||
* Adds the M150 command to set the LED (or LED strip) color.
|
* Adds the M150 command to set the LED (or LED strip) color.
|
||||||
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
||||||
* luminance values can be set from 0 to 255.
|
* luminance values can be set from 0 to 255.
|
||||||
|
* For Neopixel LED overall brightness parameters is also available
|
||||||
*
|
*
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
||||||
* as the Arduino cannot handle the current the LEDs will require.
|
* as the Arduino cannot handle the current the LEDs will require.
|
||||||
* Failure to follow this precaution can destroy your Arduino!
|
* Failure to follow this precaution can destroy your Arduino!
|
||||||
|
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino
|
||||||
|
* cannot handle the current, separate 5V power supply must be used
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
*
|
*
|
||||||
|
* LED type. This options are mutualy exclusive. Uncomment only one.
|
||||||
|
*
|
||||||
*/
|
*/
|
||||||
|
|
||||||
//#define RGB_LED
|
//#define RGB_LED
|
||||||
//#define RGBW_LED
|
//#define RGBW_LED
|
||||||
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
||||||
|
@ -1606,11 +1612,14 @@
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
// Support for Adafruit Neopixel LED driver
|
// Support for Adafruit Neopixel LED driver
|
||||||
//#define NEOPIXEL_RGBW_LED
|
//#define NEOPIXEL_LED
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(NEOPIXEL_LED)
|
||||||
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
|
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
|
||||||
#define NEOPIXEL_PIXELS 3
|
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
|
||||||
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
|
||||||
|
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
|
||||||
|
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
|
||||||
|
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
@ -1624,7 +1633,7 @@
|
||||||
* - Change to green once print has finished
|
* - Change to green once print has finished
|
||||||
* - Turn off after the print has finished and the user has pushed a button
|
* - Turn off after the print has finished and the user has pushed a button
|
||||||
*/
|
*/
|
||||||
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
|
||||||
#define PRINTER_EVENT_LEDS
|
#define PRINTER_EVENT_LEDS
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -1588,14 +1588,20 @@
|
||||||
* Adds the M150 command to set the LED (or LED strip) color.
|
* Adds the M150 command to set the LED (or LED strip) color.
|
||||||
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
||||||
* luminance values can be set from 0 to 255.
|
* luminance values can be set from 0 to 255.
|
||||||
|
* For Neopixel LED overall brightness parameters is also available
|
||||||
*
|
*
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
||||||
* as the Arduino cannot handle the current the LEDs will require.
|
* as the Arduino cannot handle the current the LEDs will require.
|
||||||
* Failure to follow this precaution can destroy your Arduino!
|
* Failure to follow this precaution can destroy your Arduino!
|
||||||
|
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino
|
||||||
|
* cannot handle the current, separate 5V power supply must be used
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
*
|
*
|
||||||
|
* LED type. This options are mutualy exclusive. Uncomment only one.
|
||||||
|
*
|
||||||
*/
|
*/
|
||||||
|
|
||||||
//#define RGB_LED
|
//#define RGB_LED
|
||||||
//#define RGBW_LED
|
//#define RGBW_LED
|
||||||
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
||||||
|
@ -1606,11 +1612,14 @@
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
// Support for Adafruit Neopixel LED driver
|
// Support for Adafruit Neopixel LED driver
|
||||||
//#define NEOPIXEL_RGBW_LED
|
//#define NEOPIXEL_LED
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(NEOPIXEL_LED)
|
||||||
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
|
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
|
||||||
#define NEOPIXEL_PIXELS 3
|
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
|
||||||
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
|
||||||
|
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
|
||||||
|
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
|
||||||
|
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
@ -1624,7 +1633,7 @@
|
||||||
* - Change to green once print has finished
|
* - Change to green once print has finished
|
||||||
* - Turn off after the print has finished and the user has pushed a button
|
* - Turn off after the print has finished and the user has pushed a button
|
||||||
*/
|
*/
|
||||||
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
|
||||||
#define PRINTER_EVENT_LEDS
|
#define PRINTER_EVENT_LEDS
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -1588,14 +1588,20 @@
|
||||||
* Adds the M150 command to set the LED (or LED strip) color.
|
* Adds the M150 command to set the LED (or LED strip) color.
|
||||||
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
||||||
* luminance values can be set from 0 to 255.
|
* luminance values can be set from 0 to 255.
|
||||||
|
* For Neopixel LED overall brightness parameters is also available
|
||||||
*
|
*
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
||||||
* as the Arduino cannot handle the current the LEDs will require.
|
* as the Arduino cannot handle the current the LEDs will require.
|
||||||
* Failure to follow this precaution can destroy your Arduino!
|
* Failure to follow this precaution can destroy your Arduino!
|
||||||
|
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino
|
||||||
|
* cannot handle the current, separate 5V power supply must be used
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
*
|
*
|
||||||
|
* LED type. This options are mutualy exclusive. Uncomment only one.
|
||||||
|
*
|
||||||
*/
|
*/
|
||||||
|
|
||||||
//#define RGB_LED
|
//#define RGB_LED
|
||||||
//#define RGBW_LED
|
//#define RGBW_LED
|
||||||
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
||||||
|
@ -1606,11 +1612,14 @@
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
// Support for Adafruit Neopixel LED driver
|
// Support for Adafruit Neopixel LED driver
|
||||||
//#define NEOPIXEL_RGBW_LED
|
//#define NEOPIXEL_LED
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(NEOPIXEL_LED)
|
||||||
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
|
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
|
||||||
#define NEOPIXEL_PIXELS 3
|
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
|
||||||
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
|
||||||
|
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
|
||||||
|
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
|
||||||
|
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
@ -1624,7 +1633,7 @@
|
||||||
* - Change to green once print has finished
|
* - Change to green once print has finished
|
||||||
* - Turn off after the print has finished and the user has pushed a button
|
* - Turn off after the print has finished and the user has pushed a button
|
||||||
*/
|
*/
|
||||||
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
|
||||||
#define PRINTER_EVENT_LEDS
|
#define PRINTER_EVENT_LEDS
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -1716,14 +1716,20 @@
|
||||||
* Adds the M150 command to set the LED (or LED strip) color.
|
* Adds the M150 command to set the LED (or LED strip) color.
|
||||||
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
||||||
* luminance values can be set from 0 to 255.
|
* luminance values can be set from 0 to 255.
|
||||||
|
* For Neopixel LED overall brightness parameters is also available
|
||||||
*
|
*
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
||||||
* as the Arduino cannot handle the current the LEDs will require.
|
* as the Arduino cannot handle the current the LEDs will require.
|
||||||
* Failure to follow this precaution can destroy your Arduino!
|
* Failure to follow this precaution can destroy your Arduino!
|
||||||
|
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino
|
||||||
|
* cannot handle the current, separate 5V power supply must be used
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
*
|
*
|
||||||
|
* LED type. This options are mutualy exclusive. Uncomment only one.
|
||||||
|
*
|
||||||
*/
|
*/
|
||||||
|
|
||||||
//#define RGB_LED
|
//#define RGB_LED
|
||||||
//#define RGBW_LED
|
//#define RGBW_LED
|
||||||
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
||||||
|
@ -1734,11 +1740,14 @@
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
// Support for Adafruit Neopixel LED driver
|
// Support for Adafruit Neopixel LED driver
|
||||||
//#define NEOPIXEL_RGBW_LED
|
//#define NEOPIXEL_LED
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(NEOPIXEL_LED)
|
||||||
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
|
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
|
||||||
#define NEOPIXEL_PIXELS 3
|
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
|
||||||
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
|
||||||
|
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
|
||||||
|
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
|
||||||
|
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
@ -1752,7 +1761,7 @@
|
||||||
* - Change to green once print has finished
|
* - Change to green once print has finished
|
||||||
* - Turn off after the print has finished and the user has pushed a button
|
* - Turn off after the print has finished and the user has pushed a button
|
||||||
*/
|
*/
|
||||||
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
|
||||||
#define PRINTER_EVENT_LEDS
|
#define PRINTER_EVENT_LEDS
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -1709,14 +1709,20 @@
|
||||||
* Adds the M150 command to set the LED (or LED strip) color.
|
* Adds the M150 command to set the LED (or LED strip) color.
|
||||||
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
||||||
* luminance values can be set from 0 to 255.
|
* luminance values can be set from 0 to 255.
|
||||||
|
* For Neopixel LED overall brightness parameters is also available
|
||||||
*
|
*
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
||||||
* as the Arduino cannot handle the current the LEDs will require.
|
* as the Arduino cannot handle the current the LEDs will require.
|
||||||
* Failure to follow this precaution can destroy your Arduino!
|
* Failure to follow this precaution can destroy your Arduino!
|
||||||
|
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino
|
||||||
|
* cannot handle the current, separate 5V power supply must be used
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
*
|
*
|
||||||
|
* LED type. This options are mutualy exclusive. Uncomment only one.
|
||||||
|
*
|
||||||
*/
|
*/
|
||||||
|
|
||||||
//#define RGB_LED
|
//#define RGB_LED
|
||||||
//#define RGBW_LED
|
//#define RGBW_LED
|
||||||
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
||||||
|
@ -1727,11 +1733,14 @@
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
// Support for Adafruit Neopixel LED driver
|
// Support for Adafruit Neopixel LED driver
|
||||||
//#define NEOPIXEL_RGBW_LED
|
//#define NEOPIXEL_LED
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(NEOPIXEL_LED)
|
||||||
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
|
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
|
||||||
#define NEOPIXEL_PIXELS 3
|
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
|
||||||
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
|
||||||
|
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
|
||||||
|
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
|
||||||
|
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
@ -1745,7 +1754,7 @@
|
||||||
* - Change to green once print has finished
|
* - Change to green once print has finished
|
||||||
* - Turn off after the print has finished and the user has pushed a button
|
* - Turn off after the print has finished and the user has pushed a button
|
||||||
*/
|
*/
|
||||||
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
|
||||||
#define PRINTER_EVENT_LEDS
|
#define PRINTER_EVENT_LEDS
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -1704,14 +1704,20 @@
|
||||||
* Adds the M150 command to set the LED (or LED strip) color.
|
* Adds the M150 command to set the LED (or LED strip) color.
|
||||||
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
||||||
* luminance values can be set from 0 to 255.
|
* luminance values can be set from 0 to 255.
|
||||||
|
* For Neopixel LED overall brightness parameters is also available
|
||||||
*
|
*
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
||||||
* as the Arduino cannot handle the current the LEDs will require.
|
* as the Arduino cannot handle the current the LEDs will require.
|
||||||
* Failure to follow this precaution can destroy your Arduino!
|
* Failure to follow this precaution can destroy your Arduino!
|
||||||
|
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino
|
||||||
|
* cannot handle the current, separate 5V power supply must be used
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
*
|
*
|
||||||
|
* LED type. This options are mutualy exclusive. Uncomment only one.
|
||||||
|
*
|
||||||
*/
|
*/
|
||||||
|
|
||||||
//#define RGB_LED
|
//#define RGB_LED
|
||||||
//#define RGBW_LED
|
//#define RGBW_LED
|
||||||
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
||||||
|
@ -1722,11 +1728,14 @@
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
// Support for Adafruit Neopixel LED driver
|
// Support for Adafruit Neopixel LED driver
|
||||||
//#define NEOPIXEL_RGBW_LED
|
//#define NEOPIXEL_LED
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(NEOPIXEL_LED)
|
||||||
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
|
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
|
||||||
#define NEOPIXEL_PIXELS 3
|
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
|
||||||
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
|
||||||
|
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
|
||||||
|
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
|
||||||
|
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
@ -1740,7 +1749,7 @@
|
||||||
* - Change to green once print has finished
|
* - Change to green once print has finished
|
||||||
* - Turn off after the print has finished and the user has pushed a button
|
* - Turn off after the print has finished and the user has pushed a button
|
||||||
*/
|
*/
|
||||||
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
|
||||||
#define PRINTER_EVENT_LEDS
|
#define PRINTER_EVENT_LEDS
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -1707,14 +1707,20 @@
|
||||||
* Adds the M150 command to set the LED (or LED strip) color.
|
* Adds the M150 command to set the LED (or LED strip) color.
|
||||||
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
||||||
* luminance values can be set from 0 to 255.
|
* luminance values can be set from 0 to 255.
|
||||||
|
* For Neopixel LED overall brightness parameters is also available
|
||||||
*
|
*
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
||||||
* as the Arduino cannot handle the current the LEDs will require.
|
* as the Arduino cannot handle the current the LEDs will require.
|
||||||
* Failure to follow this precaution can destroy your Arduino!
|
* Failure to follow this precaution can destroy your Arduino!
|
||||||
|
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino
|
||||||
|
* cannot handle the current, separate 5V power supply must be used
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
*
|
*
|
||||||
|
* LED type. This options are mutualy exclusive. Uncomment only one.
|
||||||
|
*
|
||||||
*/
|
*/
|
||||||
|
|
||||||
//#define RGB_LED
|
//#define RGB_LED
|
||||||
//#define RGBW_LED
|
//#define RGBW_LED
|
||||||
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
||||||
|
@ -1725,11 +1731,14 @@
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
// Support for Adafruit Neopixel LED driver
|
// Support for Adafruit Neopixel LED driver
|
||||||
//#define NEOPIXEL_RGBW_LED
|
//#define NEOPIXEL_LED
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(NEOPIXEL_LED)
|
||||||
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
|
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
|
||||||
#define NEOPIXEL_PIXELS 3
|
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
|
||||||
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
|
||||||
|
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
|
||||||
|
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
|
||||||
|
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
@ -1743,7 +1752,7 @@
|
||||||
* - Change to green once print has finished
|
* - Change to green once print has finished
|
||||||
* - Turn off after the print has finished and the user has pushed a button
|
* - Turn off after the print has finished and the user has pushed a button
|
||||||
*/
|
*/
|
||||||
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
|
||||||
#define PRINTER_EVENT_LEDS
|
#define PRINTER_EVENT_LEDS
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -1707,14 +1707,20 @@
|
||||||
* Adds the M150 command to set the LED (or LED strip) color.
|
* Adds the M150 command to set the LED (or LED strip) color.
|
||||||
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
||||||
* luminance values can be set from 0 to 255.
|
* luminance values can be set from 0 to 255.
|
||||||
|
* For Neopixel LED overall brightness parameters is also available
|
||||||
*
|
*
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
||||||
* as the Arduino cannot handle the current the LEDs will require.
|
* as the Arduino cannot handle the current the LEDs will require.
|
||||||
* Failure to follow this precaution can destroy your Arduino!
|
* Failure to follow this precaution can destroy your Arduino!
|
||||||
|
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino
|
||||||
|
* cannot handle the current, separate 5V power supply must be used
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
*
|
*
|
||||||
|
* LED type. This options are mutualy exclusive. Uncomment only one.
|
||||||
|
*
|
||||||
*/
|
*/
|
||||||
|
|
||||||
//#define RGB_LED
|
//#define RGB_LED
|
||||||
//#define RGBW_LED
|
//#define RGBW_LED
|
||||||
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
||||||
|
@ -1725,11 +1731,14 @@
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
// Support for Adafruit Neopixel LED driver
|
// Support for Adafruit Neopixel LED driver
|
||||||
//#define NEOPIXEL_RGBW_LED
|
//#define NEOPIXEL_LED
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(NEOPIXEL_LED)
|
||||||
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
|
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
|
||||||
#define NEOPIXEL_PIXELS 3
|
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
|
||||||
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
|
||||||
|
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
|
||||||
|
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
|
||||||
|
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
@ -1743,7 +1752,7 @@
|
||||||
* - Change to green once print has finished
|
* - Change to green once print has finished
|
||||||
* - Turn off after the print has finished and the user has pushed a button
|
* - Turn off after the print has finished and the user has pushed a button
|
||||||
*/
|
*/
|
||||||
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
|
||||||
#define PRINTER_EVENT_LEDS
|
#define PRINTER_EVENT_LEDS
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -1716,14 +1716,20 @@
|
||||||
* Adds the M150 command to set the LED (or LED strip) color.
|
* Adds the M150 command to set the LED (or LED strip) color.
|
||||||
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
||||||
* luminance values can be set from 0 to 255.
|
* luminance values can be set from 0 to 255.
|
||||||
|
* For Neopixel LED overall brightness parameters is also available
|
||||||
*
|
*
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
||||||
* as the Arduino cannot handle the current the LEDs will require.
|
* as the Arduino cannot handle the current the LEDs will require.
|
||||||
* Failure to follow this precaution can destroy your Arduino!
|
* Failure to follow this precaution can destroy your Arduino!
|
||||||
|
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino
|
||||||
|
* cannot handle the current, separate 5V power supply must be used
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
*
|
*
|
||||||
|
* LED type. This options are mutualy exclusive. Uncomment only one.
|
||||||
|
*
|
||||||
*/
|
*/
|
||||||
|
|
||||||
//#define RGB_LED
|
//#define RGB_LED
|
||||||
//#define RGBW_LED
|
//#define RGBW_LED
|
||||||
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
||||||
|
@ -1734,11 +1740,14 @@
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
// Support for Adafruit Neopixel LED driver
|
// Support for Adafruit Neopixel LED driver
|
||||||
//#define NEOPIXEL_RGBW_LED
|
//#define NEOPIXEL_LED
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(NEOPIXEL_LED)
|
||||||
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
|
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
|
||||||
#define NEOPIXEL_PIXELS 3
|
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
|
||||||
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
|
||||||
|
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
|
||||||
|
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
|
||||||
|
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
@ -1752,7 +1761,7 @@
|
||||||
* - Change to green once print has finished
|
* - Change to green once print has finished
|
||||||
* - Turn off after the print has finished and the user has pushed a button
|
* - Turn off after the print has finished and the user has pushed a button
|
||||||
*/
|
*/
|
||||||
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
|
||||||
#define PRINTER_EVENT_LEDS
|
#define PRINTER_EVENT_LEDS
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -1602,14 +1602,20 @@
|
||||||
* Adds the M150 command to set the LED (or LED strip) color.
|
* Adds the M150 command to set the LED (or LED strip) color.
|
||||||
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
||||||
* luminance values can be set from 0 to 255.
|
* luminance values can be set from 0 to 255.
|
||||||
|
* For Neopixel LED overall brightness parameters is also available
|
||||||
*
|
*
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
||||||
* as the Arduino cannot handle the current the LEDs will require.
|
* as the Arduino cannot handle the current the LEDs will require.
|
||||||
* Failure to follow this precaution can destroy your Arduino!
|
* Failure to follow this precaution can destroy your Arduino!
|
||||||
|
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino
|
||||||
|
* cannot handle the current, separate 5V power supply must be used
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
*
|
*
|
||||||
|
* LED type. This options are mutualy exclusive. Uncomment only one.
|
||||||
|
*
|
||||||
*/
|
*/
|
||||||
|
|
||||||
//#define RGB_LED
|
//#define RGB_LED
|
||||||
//#define RGBW_LED
|
//#define RGBW_LED
|
||||||
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
||||||
|
@ -1620,11 +1626,14 @@
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
// Support for Adafruit Neopixel LED driver
|
// Support for Adafruit Neopixel LED driver
|
||||||
//#define NEOPIXEL_RGBW_LED
|
//#define NEOPIXEL_LED
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(NEOPIXEL_LED)
|
||||||
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
|
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
|
||||||
#define NEOPIXEL_PIXELS 3
|
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
|
||||||
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
|
||||||
|
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
|
||||||
|
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
|
||||||
|
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
@ -1638,7 +1647,7 @@
|
||||||
* - Change to green once print has finished
|
* - Change to green once print has finished
|
||||||
* - Turn off after the print has finished and the user has pushed a button
|
* - Turn off after the print has finished and the user has pushed a button
|
||||||
*/
|
*/
|
||||||
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
|
||||||
#define PRINTER_EVENT_LEDS
|
#define PRINTER_EVENT_LEDS
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -1591,14 +1591,20 @@
|
||||||
* Adds the M150 command to set the LED (or LED strip) color.
|
* Adds the M150 command to set the LED (or LED strip) color.
|
||||||
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
||||||
* luminance values can be set from 0 to 255.
|
* luminance values can be set from 0 to 255.
|
||||||
|
* For Neopixel LED overall brightness parameters is also available
|
||||||
*
|
*
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
||||||
* as the Arduino cannot handle the current the LEDs will require.
|
* as the Arduino cannot handle the current the LEDs will require.
|
||||||
* Failure to follow this precaution can destroy your Arduino!
|
* Failure to follow this precaution can destroy your Arduino!
|
||||||
|
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino
|
||||||
|
* cannot handle the current, separate 5V power supply must be used
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
*
|
*
|
||||||
|
* LED type. This options are mutualy exclusive. Uncomment only one.
|
||||||
|
*
|
||||||
*/
|
*/
|
||||||
|
|
||||||
//#define RGB_LED
|
//#define RGB_LED
|
||||||
//#define RGBW_LED
|
//#define RGBW_LED
|
||||||
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
||||||
|
@ -1609,11 +1615,14 @@
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
// Support for Adafruit Neopixel LED driver
|
// Support for Adafruit Neopixel LED driver
|
||||||
//#define NEOPIXEL_RGBW_LED
|
//#define NEOPIXEL_LED
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(NEOPIXEL_LED)
|
||||||
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
|
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
|
||||||
#define NEOPIXEL_PIXELS 3
|
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
|
||||||
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
|
||||||
|
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
|
||||||
|
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
|
||||||
|
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
@ -1627,7 +1636,7 @@
|
||||||
* - Change to green once print has finished
|
* - Change to green once print has finished
|
||||||
* - Turn off after the print has finished and the user has pushed a button
|
* - Turn off after the print has finished and the user has pushed a button
|
||||||
*/
|
*/
|
||||||
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
|
||||||
#define PRINTER_EVENT_LEDS
|
#define PRINTER_EVENT_LEDS
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -1561,11 +1561,14 @@
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
// Support for Adafruit Neopixel LED driver
|
// Support for Adafruit Neopixel LED driver
|
||||||
//#define NEOPIXEL_RGBW_LED
|
//#define NEOPIXEL_LED
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(NEOPIXEL_LED)
|
||||||
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
|
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
|
||||||
#define NEOPIXEL_PIXELS 3
|
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
|
||||||
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
|
||||||
|
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
|
||||||
|
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
|
||||||
|
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
@ -1579,7 +1582,7 @@
|
||||||
* - Change to green once print has finished
|
* - Change to green once print has finished
|
||||||
* - Turn off after the print has finished and the user has pushed a button
|
* - Turn off after the print has finished and the user has pushed a button
|
||||||
*/
|
*/
|
||||||
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
|
||||||
#define PRINTER_EVENT_LEDS
|
#define PRINTER_EVENT_LEDS
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -1583,14 +1583,20 @@
|
||||||
* Adds the M150 command to set the LED (or LED strip) color.
|
* Adds the M150 command to set the LED (or LED strip) color.
|
||||||
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
||||||
* luminance values can be set from 0 to 255.
|
* luminance values can be set from 0 to 255.
|
||||||
|
* For Neopixel LED overall brightness parameters is also available
|
||||||
*
|
*
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
||||||
* as the Arduino cannot handle the current the LEDs will require.
|
* as the Arduino cannot handle the current the LEDs will require.
|
||||||
* Failure to follow this precaution can destroy your Arduino!
|
* Failure to follow this precaution can destroy your Arduino!
|
||||||
|
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino
|
||||||
|
* cannot handle the current, separate 5V power supply must be used
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
*
|
*
|
||||||
|
* LED type. This options are mutualy exclusive. Uncomment only one.
|
||||||
|
*
|
||||||
*/
|
*/
|
||||||
|
|
||||||
//#define RGB_LED
|
//#define RGB_LED
|
||||||
//#define RGBW_LED
|
//#define RGBW_LED
|
||||||
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
||||||
|
@ -1601,11 +1607,14 @@
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
// Support for Adafruit Neopixel LED driver
|
// Support for Adafruit Neopixel LED driver
|
||||||
//#define NEOPIXEL_RGBW_LED
|
//#define NEOPIXEL_LED
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(NEOPIXEL_LED)
|
||||||
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
|
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
|
||||||
#define NEOPIXEL_PIXELS 3
|
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
|
||||||
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
|
||||||
|
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
|
||||||
|
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
|
||||||
|
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
@ -1619,7 +1628,7 @@
|
||||||
* - Change to green once print has finished
|
* - Change to green once print has finished
|
||||||
* - Turn off after the print has finished and the user has pushed a button
|
* - Turn off after the print has finished and the user has pushed a button
|
||||||
*/
|
*/
|
||||||
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
|
||||||
#define PRINTER_EVENT_LEDS
|
#define PRINTER_EVENT_LEDS
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -1593,14 +1593,20 @@
|
||||||
* Adds the M150 command to set the LED (or LED strip) color.
|
* Adds the M150 command to set the LED (or LED strip) color.
|
||||||
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
* If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of
|
||||||
* luminance values can be set from 0 to 255.
|
* luminance values can be set from 0 to 255.
|
||||||
|
* For Neopixel LED overall brightness parameters is also available
|
||||||
*
|
*
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
* LED Strips require a MOFSET Chip between PWM lines and LEDs,
|
||||||
* as the Arduino cannot handle the current the LEDs will require.
|
* as the Arduino cannot handle the current the LEDs will require.
|
||||||
* Failure to follow this precaution can destroy your Arduino!
|
* Failure to follow this precaution can destroy your Arduino!
|
||||||
|
* Neopixel LED is 5V powered, but linear 5V regulator on Arduino
|
||||||
|
* cannot handle the current, separate 5V power supply must be used
|
||||||
* *** CAUTION ***
|
* *** CAUTION ***
|
||||||
*
|
*
|
||||||
|
* LED type. This options are mutualy exclusive. Uncomment only one.
|
||||||
|
*
|
||||||
*/
|
*/
|
||||||
|
|
||||||
//#define RGB_LED
|
//#define RGB_LED
|
||||||
//#define RGBW_LED
|
//#define RGBW_LED
|
||||||
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
#if ENABLED(RGB_LED) || ENABLED(RGBW_LED)
|
||||||
|
@ -1611,11 +1617,14 @@
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
// Support for Adafruit Neopixel LED driver
|
// Support for Adafruit Neopixel LED driver
|
||||||
//#define NEOPIXEL_RGBW_LED
|
//#define NEOPIXEL_LED
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(NEOPIXEL_LED)
|
||||||
#define NEOPIXEL_PIN 4 // D4 (EXP2-5 on Printrboard)
|
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (definned in Adafruit_NeoPixel.h)
|
||||||
#define NEOPIXEL_PIXELS 3
|
#define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
|
||||||
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
#define NEOPIXEL_PIXELS 30 // Number of LEDs on strip
|
||||||
|
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Comment out for all LEDs to change at once.
|
||||||
|
#define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255
|
||||||
|
//#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
@ -1629,7 +1638,7 @@
|
||||||
* - Change to green once print has finished
|
* - Change to green once print has finished
|
||||||
* - Turn off after the print has finished and the user has pushed a button
|
* - Turn off after the print has finished and the user has pushed a button
|
||||||
*/
|
*/
|
||||||
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)
|
||||||
#define PRINTER_EVENT_LEDS
|
#define PRINTER_EVENT_LEDS
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -31,18 +31,15 @@
|
||||||
#include "leds.h"
|
#include "leds.h"
|
||||||
|
|
||||||
void set_led_color(
|
void set_led_color(
|
||||||
const uint8_t r, const uint8_t g, const uint8_t b
|
const uint8_t r, const uint8_t g, const uint8_t b , const uint8_t w , const uint8_t p
|
||||||
#if ENABLED(RGBW_LED) || ENABLED(NEOPIXEL_RGBW_LED)
|
|
||||||
, const uint8_t w
|
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
|
||||||
, bool isSequence
|
|
||||||
#endif
|
|
||||||
#endif
|
|
||||||
) {
|
) {
|
||||||
|
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(NEOPIXEL_LED)
|
||||||
if (neopixel_set_led_color(r, g, b, w, isSequence))
|
if (w == 255 || (r == 255 && g == 255 && b == 255))
|
||||||
return;
|
neopixel_set_led_color(NEO_WHITE, p);
|
||||||
|
else
|
||||||
|
neopixel_set_led_color(r, g, b, w, p);
|
||||||
|
return;
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
#if ENABLED(BLINKM)
|
#if ENABLED(BLINKM)
|
||||||
|
|
|
@ -27,7 +27,7 @@
|
||||||
#ifndef __LEDS_H__
|
#ifndef __LEDS_H__
|
||||||
#define __LEDS_H__
|
#define __LEDS_H__
|
||||||
|
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(NEOPIXEL_LED)
|
||||||
#include <Adafruit_NeoPixel.h>
|
#include <Adafruit_NeoPixel.h>
|
||||||
#include "neopixel.h"
|
#include "neopixel.h"
|
||||||
#endif
|
#endif
|
||||||
|
@ -40,14 +40,28 @@
|
||||||
#include "pca9632.h"
|
#include "pca9632.h"
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
void set_led_color(
|
#if ENABLED(NEOPIXEL_LED)
|
||||||
const uint8_t r, const uint8_t g, const uint8_t b
|
#if NEOPIXEL_TYPE == NEO_RGB || NEOPIXEL_TYPE == NEO_RBG || NEOPIXEL_TYPE == NEO_GRB || NEOPIXEL_TYPE == NEO_GBR || NEOPIXEL_TYPE == NEO_BRG || NEOPIXEL_TYPE == NEO_BGR
|
||||||
#if ENABLED(RGBW_LED) || ENABLED(NEOPIXEL_RGBW_LED)
|
#define NEO_WHITE 255, 255, 255
|
||||||
, const uint8_t w = 0
|
#else
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
#define NEO_WHITE 0, 0, 0, 255
|
||||||
, bool isSequence = false
|
|
||||||
#endif
|
|
||||||
#endif
|
#endif
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#if ENABLED(RGB_LED) || ENABLED(BLINKM) || ENABLED(PCA9632)
|
||||||
|
#define LED_WHITE 255, 255, 255
|
||||||
|
#elif ENABLED(RGBW_LED)
|
||||||
|
#define LED_WHITE 0, 0, 0, 255
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#if ENABLED(NEOPIXEL_LED)
|
||||||
|
#define LED_BRIGHTNESS pixels.getBrightness()
|
||||||
|
#else
|
||||||
|
#define LED_BRIGHTNESS 255
|
||||||
|
#endif
|
||||||
|
|
||||||
|
void set_led_color(
|
||||||
|
const uint8_t r, const uint8_t g, const uint8_t b, const uint8_t w = 0, const uint8_t p = 255
|
||||||
);
|
);
|
||||||
|
|
||||||
#endif // __LEDS_H__
|
#endif // __LEDS_H__
|
||||||
|
|
|
@ -26,11 +26,11 @@
|
||||||
|
|
||||||
#include "../../inc/MarlinConfig.h"
|
#include "../../inc/MarlinConfig.h"
|
||||||
|
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(NEOPIXEL_LED)
|
||||||
|
|
||||||
#include "neopixel.h"
|
#include "neopixel.h"
|
||||||
|
|
||||||
Adafruit_NeoPixel pixels(NEOPIXEL_PIXELS, NEOPIXEL_PIN, NEO_GRBW + NEO_KHZ800);
|
Adafruit_NeoPixel pixels(NEOPIXEL_PIXELS, NEOPIXEL_PIN, NEOPIXEL_TYPE + NEO_KHZ800);
|
||||||
|
|
||||||
void set_neopixel_color(const uint32_t color) {
|
void set_neopixel_color(const uint32_t color) {
|
||||||
for (uint16_t i = 0; i < pixels.numPixels(); ++i)
|
for (uint16_t i = 0; i < pixels.numPixels(); ++i)
|
||||||
|
@ -39,7 +39,7 @@ void set_neopixel_color(const uint32_t color) {
|
||||||
}
|
}
|
||||||
|
|
||||||
void setup_neopixel() {
|
void setup_neopixel() {
|
||||||
pixels.setBrightness(255); // 0 - 255 range
|
pixels.setBrightness(NEOPIXEL_BRIGHTNESS); // 0 - 255 range
|
||||||
pixels.begin();
|
pixels.begin();
|
||||||
pixels.show(); // initialize to all off
|
pixels.show(); // initialize to all off
|
||||||
|
|
||||||
|
@ -55,18 +55,19 @@ void setup_neopixel() {
|
||||||
set_neopixel_color(pixels.Color(0, 0, 0, 255)); // white
|
set_neopixel_color(pixels.Color(0, 0, 0, 255)); // white
|
||||||
}
|
}
|
||||||
|
|
||||||
bool neopixel_set_led_color(const uint8_t r, const uint8_t g, const uint8_t b, const uint8_t w, const bool isSequence) {
|
bool neopixel_set_led_color(const uint8_t r, const uint8_t g, const uint8_t b, const uint8_t w, const uint8_t p) {
|
||||||
const uint32_t color = pixels.Color(r, g, b, w);
|
const uint32_t color = pixels.Color(r, g, b, w);
|
||||||
static uint16_t nextLed = 0;
|
pixels.setBrightness(p);
|
||||||
if (!isSequence)
|
#if !ENABLED(NEOPIXEL_IS_SEQUENTIAL)
|
||||||
set_neopixel_color(color);
|
set_neopixel_color(color);
|
||||||
else {
|
return false;
|
||||||
|
#else
|
||||||
|
static uint16_t nextLed = 0;
|
||||||
pixels.setPixelColor(nextLed, color);
|
pixels.setPixelColor(nextLed, color);
|
||||||
pixels.show();
|
pixels.show();
|
||||||
if (++nextLed >= pixels.numPixels()) nextLed = 0;
|
if (++nextLed >= pixels.numPixels()) nextLed = 0;
|
||||||
return true;
|
return true;
|
||||||
}
|
#endif
|
||||||
return false;
|
|
||||||
}
|
}
|
||||||
|
|
||||||
#endif // NEOPIXEL_RGBW_LED
|
#endif // NEOPIXEL_LED
|
||||||
|
|
|
@ -31,7 +31,7 @@
|
||||||
#include <stdint.h>
|
#include <stdint.h>
|
||||||
|
|
||||||
void setup_neopixel();
|
void setup_neopixel();
|
||||||
bool neopixel_set_led_color(const uint8_t r, const uint8_t g, const uint8_t b, const uint8_t w, const bool isSequence);
|
bool neopixel_set_led_color(const uint8_t r, const uint8_t g, const uint8_t b, const uint8_t w, const uint8_t p);
|
||||||
|
|
||||||
extern Adafruit_NeoPixel pixels;
|
extern Adafruit_NeoPixel pixels;
|
||||||
|
|
||||||
|
|
|
@ -28,27 +28,30 @@
|
||||||
#include "../../../feature/leds/leds.h"
|
#include "../../../feature/leds/leds.h"
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* M150: Set Status LED Color - Use R-U-B-W for R-G-B-W
|
* M150: Set Status LED Color - Use R-U-B-W for R-G-B-W
|
||||||
*
|
* and Brightness - Use P (for NEOPIXEL only)
|
||||||
* Always sets all 3 or 4 components. If a component is left out, set to 0.
|
*
|
||||||
*
|
* Always sets all 3 or 4 components. If a component is left out, set to 0.
|
||||||
* Examples:
|
* If brightness is left out, no value changed
|
||||||
*
|
*
|
||||||
* M150 R255 ; Turn LED red
|
* Examples:
|
||||||
* M150 R255 U127 ; Turn LED orange (PWM only)
|
*
|
||||||
* M150 ; Turn LED off
|
* M150 R255 ; Turn LED red
|
||||||
* M150 R U B ; Turn LED white
|
* M150 R255 U127 ; Turn LED orange (PWM only)
|
||||||
* M150 W ; Turn LED white using a white LED
|
* M150 ; Turn LED off
|
||||||
*
|
* M150 R U B ; Turn LED white
|
||||||
*/
|
* M150 W ; Turn LED white using a white LED
|
||||||
|
* M150 P127 ; Set LED 50% brightness
|
||||||
|
* M150 P ; Set LED full brightness
|
||||||
|
*/
|
||||||
|
|
||||||
void GcodeSuite::M150() {
|
void GcodeSuite::M150() {
|
||||||
set_led_color(
|
set_led_color(
|
||||||
parser.seen('R') ? (parser.has_value() ? parser.value_byte() : 255) : 0,
|
parser.seen('R') ? (parser.has_value() ? parser.value_byte() : 255) : 0,
|
||||||
parser.seen('U') ? (parser.has_value() ? parser.value_byte() : 255) : 0,
|
parser.seen('U') ? (parser.has_value() ? parser.value_byte() : 255) : 0,
|
||||||
parser.seen('B') ? (parser.has_value() ? parser.value_byte() : 255) : 0
|
parser.seen('B') ? (parser.has_value() ? parser.value_byte() : 255) : 0,
|
||||||
#if ENABLED(RGBW_LED) || ENABLED(NEOPIXEL_RGBW_LED)
|
parser.seen('W') ? (parser.has_value() ? parser.value_byte() : 255) : 0,
|
||||||
, parser.seen('W') ? (parser.has_value() ? parser.value_byte() : 255) : 0
|
parser.seen('P') ? (parser.has_value() ? parser.value_byte() : 255) : LED_BRIGHTNESS
|
||||||
#endif
|
|
||||||
);
|
);
|
||||||
}
|
}
|
||||||
|
|
||||||
|
|
|
@ -138,7 +138,7 @@
|
||||||
* M140 - Set bed target temp. S<temp>
|
* M140 - Set bed target temp. S<temp>
|
||||||
* M145 - Set heatup values for materials on the LCD. H<hotend> B<bed> F<fan speed> for S<material> (0=PLA, 1=ABS)
|
* M145 - Set heatup values for materials on the LCD. H<hotend> B<bed> F<fan speed> for S<material> (0=PLA, 1=ABS)
|
||||||
* M149 - Set temperature units. (Requires TEMPERATURE_UNITS_SUPPORT)
|
* M149 - Set temperature units. (Requires TEMPERATURE_UNITS_SUPPORT)
|
||||||
* M150 - Set Status LED Color as R<red> U<green> B<blue>. Values 0-255. (Requires BLINKM, RGB_LED, RGBW_LED, or PCA9632)
|
* M150 - Set Status LED Color as R<red> U<green> B<blue> P<bright>. Values 0-255. (Requires BLINKM, RGB_LED, RGBW_LED, NEOPIXEL_LED, or PCA9632).
|
||||||
* M155 - Auto-report temperatures with interval of S<seconds>. (Requires AUTO_REPORT_TEMPERATURES)
|
* M155 - Auto-report temperatures with interval of S<seconds>. (Requires AUTO_REPORT_TEMPERATURES)
|
||||||
* M163 - Set a single proportion for a mixing extruder. (Requires MIXING_EXTRUDER)
|
* M163 - Set a single proportion for a mixing extruder. (Requires MIXING_EXTRUDER)
|
||||||
* M164 - Save the mix as a virtual extruder. (Requires MIXING_EXTRUDER and MIXING_VIRTUAL_TOOLS)
|
* M164 - Save the mix as a virtual extruder. (Requires MIXING_EXTRUDER and MIXING_VIRTUAL_TOOLS)
|
||||||
|
|
|
@ -31,7 +31,7 @@
|
||||||
#include "../../module/printcounter.h"
|
#include "../../module/printcounter.h"
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
#if HAS_COLOR_LEDS
|
#if ENABLED(PRINTER_EVENT_LEDS)
|
||||||
#include "../../feature/leds/leds.h"
|
#include "../../feature/leds/leds.h"
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
@ -190,11 +190,7 @@ void GcodeSuite::M109() {
|
||||||
const uint8_t blue = map(constrain(temp, start_temp, target_temp), start_temp, target_temp, 255, 0);
|
const uint8_t blue = map(constrain(temp, start_temp, target_temp), start_temp, target_temp, 255, 0);
|
||||||
if (blue != old_blue) {
|
if (blue != old_blue) {
|
||||||
old_blue = blue;
|
old_blue = blue;
|
||||||
set_led_color(255, 0, blue
|
set_led_color(255, 0, blue);
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
|
||||||
, 0, true
|
|
||||||
#endif
|
|
||||||
);
|
|
||||||
}
|
}
|
||||||
}
|
}
|
||||||
#endif
|
#endif
|
||||||
|
@ -230,10 +226,11 @@ void GcodeSuite::M109() {
|
||||||
if (wait_for_heatup) {
|
if (wait_for_heatup) {
|
||||||
LCD_MESSAGEPGM(MSG_HEATING_COMPLETE);
|
LCD_MESSAGEPGM(MSG_HEATING_COMPLETE);
|
||||||
#if ENABLED(PRINTER_EVENT_LEDS)
|
#if ENABLED(PRINTER_EVENT_LEDS)
|
||||||
#if ENABLED(RGBW_LED) || ENABLED(NEOPIXEL_RGBW_LED)
|
#if ENABLED(RGB_LED) || ENABLED(BLINKM) || ENABLED(PCA9632) || ENABLED(RGBW_LED)
|
||||||
set_led_color(0, 0, 0, 255); // Turn on the WHITE LED
|
set_led_color(LED_WHITE);
|
||||||
#else
|
#endif
|
||||||
set_led_color(255, 255, 255); // Set LEDs All On
|
#if ENABLED(NEOPIXEL_LED)
|
||||||
|
set_neopixel_color(pixels.Color(NEO_WHITE));
|
||||||
#endif
|
#endif
|
||||||
#endif
|
#endif
|
||||||
}
|
}
|
||||||
|
|
|
@ -132,11 +132,7 @@ void GcodeSuite::M190() {
|
||||||
const uint8_t red = map(constrain(temp, start_temp, target_temp), start_temp, target_temp, 0, 255);
|
const uint8_t red = map(constrain(temp, start_temp, target_temp), start_temp, target_temp, 0, 255);
|
||||||
if (red != old_red) {
|
if (red != old_red) {
|
||||||
old_red = red;
|
old_red = red;
|
||||||
set_led_color(red, 0, 255
|
set_led_color(red, 0, 255);
|
||||||
#if ENABLED(NEOPIXEL_RGBW_LED)
|
|
||||||
, 0, true
|
|
||||||
#endif
|
|
||||||
);
|
|
||||||
}
|
}
|
||||||
}
|
}
|
||||||
#endif
|
#endif
|
||||||
|
|
|
@ -483,6 +483,6 @@
|
||||||
|
|
||||||
#define HAS_SOFTWARE_ENDSTOPS (ENABLED(MIN_SOFTWARE_ENDSTOPS) || ENABLED(MAX_SOFTWARE_ENDSTOPS))
|
#define HAS_SOFTWARE_ENDSTOPS (ENABLED(MIN_SOFTWARE_ENDSTOPS) || ENABLED(MAX_SOFTWARE_ENDSTOPS))
|
||||||
#define HAS_RESUME_CONTINUE (ENABLED(NEWPANEL) || ENABLED(EMERGENCY_PARSER))
|
#define HAS_RESUME_CONTINUE (ENABLED(NEWPANEL) || ENABLED(EMERGENCY_PARSER))
|
||||||
#define HAS_COLOR_LEDS (ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_RGBW_LED))
|
#define HAS_COLOR_LEDS (ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED))
|
||||||
|
|
||||||
#endif // CONDITIONALS_LCD_H
|
#endif // CONDITIONALS_LCD_H
|
||||||
|
|
|
@ -210,6 +210,8 @@
|
||||||
#error "MIN_RETRACT is now MIN_AUTORETRACT and MAX_AUTORETRACT. Please update your Configuration_adv.h."
|
#error "MIN_RETRACT is now MIN_AUTORETRACT and MAX_AUTORETRACT. Please update your Configuration_adv.h."
|
||||||
#elif defined(ADVANCE)
|
#elif defined(ADVANCE)
|
||||||
#error "ADVANCE was removed in Marlin 1.1.6. Please use LIN_ADVANCE."
|
#error "ADVANCE was removed in Marlin 1.1.6. Please use LIN_ADVANCE."
|
||||||
|
#elif defined(NEOPIXEL_RGBW_LED)
|
||||||
|
#error "NEOPIXEL_RGBW_LED is now NEOPIXEL_LED. Please update your configuration."
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
@ -1100,12 +1102,12 @@ static_assert(1 >= 0
|
||||||
#if !(_RGB_TEST && PIN_EXISTS(RGB_LED_W))
|
#if !(_RGB_TEST && PIN_EXISTS(RGB_LED_W))
|
||||||
#error "RGBW_LED requires RGB_LED_R_PIN, RGB_LED_G_PIN, RGB_LED_B_PIN, and RGB_LED_W_PIN."
|
#error "RGBW_LED requires RGB_LED_R_PIN, RGB_LED_G_PIN, RGB_LED_B_PIN, and RGB_LED_W_PIN."
|
||||||
#endif
|
#endif
|
||||||
#elif ENABLED(NEOPIXEL_RGBW_LED)
|
#elif ENABLED(NEOPIXEL_LED)
|
||||||
#if !(PIN_EXISTS(NEOPIXEL) && NEOPIXEL_PIXELS > 0)
|
#if !(PIN_EXISTS(NEOPIXEL) && NEOPIXEL_PIXELS > 0)
|
||||||
#error "NEOPIXEL_RGBW_LED requires NEOPIXEL_PIN and NEOPIXEL_PIXELS."
|
#error "NEOPIXEL_LED requires NEOPIXEL_PIN and NEOPIXEL_PIXELS."
|
||||||
#endif
|
#endif
|
||||||
#elif ENABLED(PRINTER_EVENT_LEDS) && DISABLED(BLINKM) && DISABLED(PCA9632) && DISABLED(NEOPIXEL_RGBW_LED)
|
#elif ENABLED(PRINTER_EVENT_LEDS) && DISABLED(BLINKM) && DISABLED(PCA9632) && DISABLED(NEOPIXEL_LED)
|
||||||
#error "PRINTER_EVENT_LEDS requires BLINKM, PCA9632, RGB_LED, RGBW_LED or NEOPIXEL_RGBW_LED."
|
#error "PRINTER_EVENT_LEDS requires BLINKM, PCA9632, RGB_LED, RGBW_LED or NEOPIXEL_LED."
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
Loading…
Reference in a new issue