diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h
index 4f2222ffb7..2a55fb9310 100644
--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/Marlin/src/Marlin.cpp b/Marlin/src/Marlin.cpp
index d6285225c1..bde5a0850b 100644
--- a/Marlin/src/Marlin.cpp
+++ b/Marlin/src/Marlin.cpp
@@ -290,6 +290,15 @@ void enable_all_steppers() {
   enable_E5();
 }
 
+void enable_e_steppers() {
+  enable_E0();
+  enable_E1();
+  enable_E2();
+  enable_E3();
+  enable_E4();
+  enable_E5();
+}
+
 void disable_e_steppers() {
   disable_E0();
   disable_E1();
@@ -1117,6 +1126,10 @@ void setup() {
     init_closedloop();
   #endif
 
+  #ifdef STARTUP_COMMANDS
+    queue.inject_P(PSTR(STARTUP_COMMANDS));
+  #endif
+
   #if ENABLED(INIT_SDCARD_ON_BOOT) && !HAS_SPI_LCD
     card.beginautostart();
   #endif
diff --git a/Marlin/src/Marlin.h b/Marlin/src/Marlin.h
index cef5950b99..db24382bc8 100644
--- a/Marlin/src/Marlin.h
+++ b/Marlin/src/Marlin.h
@@ -316,6 +316,7 @@ void manage_inactivity(const bool ignore_stepper_queue=false);
 /**
  * The axis order in all axis related arrays is X, Y, Z, E
  */
+void enable_e_steppers();
 void enable_all_steppers();
 void disable_e_stepper(const uint8_t e);
 void disable_e_steppers();
diff --git a/Marlin/src/core/drivers.h b/Marlin/src/core/drivers.h
index 617090a6f2..005ffb7da5 100644
--- a/Marlin/src/core/drivers.h
+++ b/Marlin/src/core/drivers.h
@@ -67,12 +67,14 @@
 
 #define AXIS_DRIVER_TYPE(A,T) AXIS_DRIVER_TYPE_##A(T)
 
+#define HAS_E_DRIVER(T) (  AXIS_DRIVER_TYPE_E0(T) || AXIS_DRIVER_TYPE_E1(T) \
+                        || AXIS_DRIVER_TYPE_E2(T) || AXIS_DRIVER_TYPE_E3(T) \
+                        || AXIS_DRIVER_TYPE_E4(T) || AXIS_DRIVER_TYPE_E5(T) )
+
 #define HAS_DRIVER(T) (    AXIS_DRIVER_TYPE_X(T)  || AXIS_DRIVER_TYPE_X2(T) \
                         || AXIS_DRIVER_TYPE_Y(T)  || AXIS_DRIVER_TYPE_Y2(T) \
                         || AXIS_DRIVER_TYPE_Z(T)  || AXIS_DRIVER_TYPE_Z2(T) || AXIS_DRIVER_TYPE_Z3(T) \
-                        || AXIS_DRIVER_TYPE_E0(T) || AXIS_DRIVER_TYPE_E1(T) \
-                        || AXIS_DRIVER_TYPE_E2(T) || AXIS_DRIVER_TYPE_E3(T) \
-                        || AXIS_DRIVER_TYPE_E4(T) || AXIS_DRIVER_TYPE_E5(T) )
+                        || HAS_E_DRIVER(T) )
 
 // Test for supported TMC drivers that require advanced configuration
 // Does not match standalone configurations
diff --git a/Marlin/src/feature/pause.cpp b/Marlin/src/feature/pause.cpp
index 5700591ca3..17dd469632 100644
--- a/Marlin/src/feature/pause.cpp
+++ b/Marlin/src/feature/pause.cpp
@@ -353,8 +353,8 @@ bool unload_filament(const float &unload_length, const bool show_lcd/*=false*/,
     planner.settings.retract_acceleration = saved_acceleration;
   #endif
 
-  // Disable extruders steppers for manual filament changing (only on boards that have separate ENABLE_PINS)
-  #if (E0_ENABLE_PIN != X_ENABLE_PIN && E1_ENABLE_PIN != Y_ENABLE_PIN) || AXIS_DRIVER_TYPE_E0(TMC2660) || AXIS_DRIVER_TYPE_E1(TMC2660) || AXIS_DRIVER_TYPE_E2(TMC2660) || AXIS_DRIVER_TYPE_E3(TMC2660) || AXIS_DRIVER_TYPE_E4(TMC2660) || AXIS_DRIVER_TYPE_E5(TMC2660)
+  // Disable E steppers for manual change
+  #if HAS_E_STEPPER_ENABLE
     disable_e_stepper(active_extruder);
     safe_delay(100);
   #endif
diff --git a/Marlin/src/gcode/control/M17_M18_M84.cpp b/Marlin/src/gcode/control/M17_M18_M84.cpp
index 6706cee008..de6eab4f74 100644
--- a/Marlin/src/gcode/control/M17_M18_M84.cpp
+++ b/Marlin/src/gcode/control/M17_M18_M84.cpp
@@ -30,11 +30,21 @@
 #endif
 
 /**
- * M17: Enable power on all stepper motors
+ * M17: Enable stepper motors
  */
 void GcodeSuite::M17() {
-  LCD_MESSAGEPGM(MSG_NO_MOVE);
-  enable_all_steppers();
+  if (parser.seen("XYZE")) {
+    if (parser.seen('X')) enable_X();
+    if (parser.seen('Y')) enable_Y();
+    if (parser.seen('Z')) enable_Z();
+    #if HAS_E_STEPPER_ENABLE
+      if (parser.seen('E')) enable_e_steppers();
+    #endif
+  }
+  else {
+    LCD_MESSAGEPGM(MSG_NO_MOVE);
+    enable_all_steppers();
+  }
 }
 
 /**
@@ -45,20 +55,17 @@ void GcodeSuite::M18_M84() {
     stepper_inactive_time = parser.value_millis_from_seconds();
   }
   else {
-    bool all_axis = !(parser.seen('X') || parser.seen('Y') || parser.seen('Z') || parser.seen('E'));
-    if (all_axis) {
-      planner.finish_and_disable();
-    }
-    else {
+    if (parser.seen("XYZE")) {
       planner.synchronize();
       if (parser.seen('X')) disable_X();
       if (parser.seen('Y')) disable_Y();
       if (parser.seen('Z')) disable_Z();
-      // Only disable on boards that have separate ENABLE_PINS or another method for disabling the driver
-      #if (E0_ENABLE_PIN != X_ENABLE_PIN && E1_ENABLE_PIN != Y_ENABLE_PIN) || AXIS_DRIVER_TYPE_E0(TMC2660) || AXIS_DRIVER_TYPE_E1(TMC2660) || AXIS_DRIVER_TYPE_E2(TMC2660) || AXIS_DRIVER_TYPE_E3(TMC2660) || AXIS_DRIVER_TYPE_E4(TMC2660) || AXIS_DRIVER_TYPE_E5(TMC2660)
+      #if HAS_E_STEPPER_ENABLE
         if (parser.seen('E')) disable_e_steppers();
       #endif
     }
+    else
+      planner.finish_and_disable();
 
     #if HAS_LCD_MENU && ENABLED(AUTO_BED_LEVELING_UBL)
       if (ubl.lcd_map_control) {
diff --git a/Marlin/src/inc/Conditionals_post.h b/Marlin/src/inc/Conditionals_post.h
index c6a2efbd59..38e2ff59aa 100644
--- a/Marlin/src/inc/Conditionals_post.h
+++ b/Marlin/src/inc/Conditionals_post.h
@@ -927,6 +927,11 @@
   #endif
 #endif
 
+#define HAS_E_STEPPER_ENABLE (HAS_E_DRIVER(TMC2660) \
+  || ( E0_ENABLE_PIN != X_ENABLE_PIN && E1_ENABLE_PIN != X_ENABLE_PIN   \
+    && E0_ENABLE_PIN != Y_ENABLE_PIN && E1_ENABLE_PIN != Y_ENABLE_PIN ) \
+)
+
 // Endstops and bed probe
 #define _HAS_STOP(A,M) (PIN_EXISTS(A##_##M) && !IS_X2_ENDSTOP(A,M) && !IS_Y2_ENDSTOP(A,M) && !IS_Z2_OR_PROBE(A,M))
 #define HAS_X_MIN _HAS_STOP(X,MIN)
diff --git a/Marlin/src/libs/L6470/L6470_Marlin.h b/Marlin/src/libs/L6470/L6470_Marlin.h
index 92745b6e3e..3311574a16 100644
--- a/Marlin/src/libs/L6470/L6470_Marlin.h
+++ b/Marlin/src/libs/L6470/L6470_Marlin.h
@@ -32,8 +32,6 @@
 #define L6470_ERROR_MASK  (STATUS_UVLO | STATUS_TH_WRN | STATUS_TH_SD  | STATUS_OCD | STATUS_STEP_LOSS_A | STATUS_STEP_LOSS_B)
 #define dSPIN_STEP_CLOCK_FWD dSPIN_STEP_CLOCK
 #define dSPIN_STEP_CLOCK_REV dSPIN_STEP_CLOCK+1
-#define HAS_L6470_EXTRUDER ( AXIS_DRIVER_TYPE_E0(L6470) || AXIS_DRIVER_TYPE_E1(L6470) || AXIS_DRIVER_TYPE_E2(L6470) \
-                          || AXIS_DRIVER_TYPE_E3(L6470) || AXIS_DRIVER_TYPE_E4(L6470) || AXIS_DRIVER_TYPE_E5(L6470) )
 
 class L6470_Marlin {
 public:
diff --git a/config/default/Configuration_adv.h b/config/default/Configuration_adv.h
index 4f2222ffb7..2a55fb9310 100644
--- a/config/default/Configuration_adv.h
+++ b/config/default/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/3DFabXYZ/Migbot/Configuration_adv.h b/config/examples/3DFabXYZ/Migbot/Configuration_adv.h
index 80b4d30001..0d01c80f59 100644
--- a/config/examples/3DFabXYZ/Migbot/Configuration_adv.h
+++ b/config/examples/3DFabXYZ/Migbot/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/AlephObjects/TAZ4/Configuration_adv.h b/config/examples/AlephObjects/TAZ4/Configuration_adv.h
index fa932eb8b4..0a5d1fcca0 100644
--- a/config/examples/AlephObjects/TAZ4/Configuration_adv.h
+++ b/config/examples/AlephObjects/TAZ4/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Alfawise/U20/Configuration_adv.h b/config/examples/Alfawise/U20/Configuration_adv.h
index 6c805e1a19..0e50ac43a8 100644
--- a/config/examples/Alfawise/U20/Configuration_adv.h
+++ b/config/examples/Alfawise/U20/Configuration_adv.h
@@ -2306,6 +2306,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/AliExpress/UM2pExt/Configuration_adv.h b/config/examples/AliExpress/UM2pExt/Configuration_adv.h
index 728e71218c..188529d99f 100644
--- a/config/examples/AliExpress/UM2pExt/Configuration_adv.h
+++ b/config/examples/AliExpress/UM2pExt/Configuration_adv.h
@@ -2305,6 +2305,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Anet/A2/Configuration_adv.h b/config/examples/Anet/A2/Configuration_adv.h
index 0c44124c95..7c7c27a511 100644
--- a/config/examples/Anet/A2/Configuration_adv.h
+++ b/config/examples/Anet/A2/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Anet/A2plus/Configuration_adv.h b/config/examples/Anet/A2plus/Configuration_adv.h
index 0c44124c95..7c7c27a511 100644
--- a/config/examples/Anet/A2plus/Configuration_adv.h
+++ b/config/examples/Anet/A2plus/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Anet/A6/Configuration_adv.h b/config/examples/Anet/A6/Configuration_adv.h
index d89e3b8162..1e1cfe6ca4 100644
--- a/config/examples/Anet/A6/Configuration_adv.h
+++ b/config/examples/Anet/A6/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Anet/A8/Configuration_adv.h b/config/examples/Anet/A8/Configuration_adv.h
index 9d5e160a7b..c96ee1e255 100644
--- a/config/examples/Anet/A8/Configuration_adv.h
+++ b/config/examples/Anet/A8/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Anet/A8plus/Configuration_adv.h b/config/examples/Anet/A8plus/Configuration_adv.h
index 6f6993bc89..37f20f857c 100644
--- a/config/examples/Anet/A8plus/Configuration_adv.h
+++ b/config/examples/Anet/A8plus/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Anet/E16/Configuration_adv.h b/config/examples/Anet/E16/Configuration_adv.h
index 5f26d67311..4cbbcd3e11 100644
--- a/config/examples/Anet/E16/Configuration_adv.h
+++ b/config/examples/Anet/E16/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/AnyCubic/i3/Configuration_adv.h b/config/examples/AnyCubic/i3/Configuration_adv.h
index 7b075cd7e5..762b69495f 100644
--- a/config/examples/AnyCubic/i3/Configuration_adv.h
+++ b/config/examples/AnyCubic/i3/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/ArmEd/Configuration_adv.h b/config/examples/ArmEd/Configuration_adv.h
index d70e7a1fea..7aec83f2c3 100644
--- a/config/examples/ArmEd/Configuration_adv.h
+++ b/config/examples/ArmEd/Configuration_adv.h
@@ -2307,6 +2307,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h b/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
index c624ee7ab5..96599118bd 100644
--- a/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
+++ b/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/BIBO/TouchX/default/Configuration_adv.h b/config/examples/BIBO/TouchX/default/Configuration_adv.h
index 593aca7414..80a4bffc51 100644
--- a/config/examples/BIBO/TouchX/default/Configuration_adv.h
+++ b/config/examples/BIBO/TouchX/default/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/BQ/Hephestos/Configuration_adv.h b/config/examples/BQ/Hephestos/Configuration_adv.h
index 4f867ff6a2..7e26bb7648 100644
--- a/config/examples/BQ/Hephestos/Configuration_adv.h
+++ b/config/examples/BQ/Hephestos/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/BQ/Hephestos_2/Configuration_adv.h b/config/examples/BQ/Hephestos_2/Configuration_adv.h
index 82d19a9cc7..98d45b4dd3 100644
--- a/config/examples/BQ/Hephestos_2/Configuration_adv.h
+++ b/config/examples/BQ/Hephestos_2/Configuration_adv.h
@@ -2311,6 +2311,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/BQ/WITBOX/Configuration_adv.h b/config/examples/BQ/WITBOX/Configuration_adv.h
index 4f867ff6a2..7e26bb7648 100644
--- a/config/examples/BQ/WITBOX/Configuration_adv.h
+++ b/config/examples/BQ/WITBOX/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Cartesio/Configuration_adv.h b/config/examples/Cartesio/Configuration_adv.h
index 80d76e1833..5e7def1c03 100644
--- a/config/examples/Cartesio/Configuration_adv.h
+++ b/config/examples/Cartesio/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Creality/CR-10/Configuration_adv.h b/config/examples/Creality/CR-10/Configuration_adv.h
index ced15b855d..b4f915db75 100644
--- a/config/examples/Creality/CR-10/Configuration_adv.h
+++ b/config/examples/Creality/CR-10/Configuration_adv.h
@@ -2306,6 +2306,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Creality/CR-10S/Configuration_adv.h b/config/examples/Creality/CR-10S/Configuration_adv.h
index c5f06a7602..6b9fef608d 100644
--- a/config/examples/Creality/CR-10S/Configuration_adv.h
+++ b/config/examples/Creality/CR-10S/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Creality/CR-10_5S/Configuration_adv.h b/config/examples/Creality/CR-10_5S/Configuration_adv.h
index 5c1b5b6a54..d3b14d6a10 100644
--- a/config/examples/Creality/CR-10_5S/Configuration_adv.h
+++ b/config/examples/Creality/CR-10_5S/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Creality/CR-10mini/Configuration_adv.h b/config/examples/Creality/CR-10mini/Configuration_adv.h
index fc30c3a212..9b40688bb9 100644
--- a/config/examples/Creality/CR-10mini/Configuration_adv.h
+++ b/config/examples/Creality/CR-10mini/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Creality/CR-20 Pro/Configuration_adv.h b/config/examples/Creality/CR-20 Pro/Configuration_adv.h
index 282c116dfe..8d4ae80c8c 100644
--- a/config/examples/Creality/CR-20 Pro/Configuration_adv.h	
+++ b/config/examples/Creality/CR-20 Pro/Configuration_adv.h	
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Creality/CR-20/Configuration_adv.h b/config/examples/Creality/CR-20/Configuration_adv.h
index 32cb6765ac..1c6c91252a 100644
--- a/config/examples/Creality/CR-20/Configuration_adv.h
+++ b/config/examples/Creality/CR-20/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Creality/CR-8/Configuration_adv.h b/config/examples/Creality/CR-8/Configuration_adv.h
index a08039b80c..ed08c8b096 100644
--- a/config/examples/Creality/CR-8/Configuration_adv.h
+++ b/config/examples/Creality/CR-8/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Creality/Ender-2/Configuration_adv.h b/config/examples/Creality/Ender-2/Configuration_adv.h
index efec78ae75..c4ae7ae5ed 100644
--- a/config/examples/Creality/Ender-2/Configuration_adv.h
+++ b/config/examples/Creality/Ender-2/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Creality/Ender-3/Configuration_adv.h b/config/examples/Creality/Ender-3/Configuration_adv.h
index 885ff81cb8..e6d8a5f487 100644
--- a/config/examples/Creality/Ender-3/Configuration_adv.h
+++ b/config/examples/Creality/Ender-3/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Creality/Ender-4/Configuration_adv.h b/config/examples/Creality/Ender-4/Configuration_adv.h
index fa9ea28214..658816c66d 100644
--- a/config/examples/Creality/Ender-4/Configuration_adv.h
+++ b/config/examples/Creality/Ender-4/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Creality/Ender-5/Configuration_adv.h b/config/examples/Creality/Ender-5/Configuration_adv.h
index 6be777f6fb..515ed8ff67 100644
--- a/config/examples/Creality/Ender-5/Configuration_adv.h
+++ b/config/examples/Creality/Ender-5/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h b/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h
index a2c09ade58..dcce6aaa0c 100644
--- a/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h	
+++ b/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h	
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration_adv.h b/config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration_adv.h
index 317018380b..5b0c8ecaab 100755
--- a/config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration_adv.h	
+++ b/config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration_adv.h	
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Einstart-S/Configuration_adv.h b/config/examples/Einstart-S/Configuration_adv.h
index e70941cfc6..a817b71e37 100644
--- a/config/examples/Einstart-S/Configuration_adv.h
+++ b/config/examples/Einstart-S/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/FYSETC/AIO_II/Configuration_adv.h b/config/examples/FYSETC/AIO_II/Configuration_adv.h
index 6ed35f6c38..28d3d3768f 100644
--- a/config/examples/FYSETC/AIO_II/Configuration_adv.h
+++ b/config/examples/FYSETC/AIO_II/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h b/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h
index d98337635d..9c2eba4cc8 100644
--- a/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h	
+++ b/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h	
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h b/config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h
index 7facfb9d17..8f3c43cb65 100644
--- a/config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h	
+++ b/config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h	
@@ -2302,6 +2302,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/FYSETC/Cheetah/BLTouch/Configuration_adv.h b/config/examples/FYSETC/Cheetah/BLTouch/Configuration_adv.h
index ab3f52688c..04a5110173 100644
--- a/config/examples/FYSETC/Cheetah/BLTouch/Configuration_adv.h
+++ b/config/examples/FYSETC/Cheetah/BLTouch/Configuration_adv.h
@@ -2302,6 +2302,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/FYSETC/Cheetah/base/Configuration_adv.h b/config/examples/FYSETC/Cheetah/base/Configuration_adv.h
index ab3f52688c..04a5110173 100644
--- a/config/examples/FYSETC/Cheetah/base/Configuration_adv.h
+++ b/config/examples/FYSETC/Cheetah/base/Configuration_adv.h
@@ -2302,6 +2302,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/FYSETC/F6_13/Configuration_adv.h b/config/examples/FYSETC/F6_13/Configuration_adv.h
index 33a9058315..5eb4921e76 100644
--- a/config/examples/FYSETC/F6_13/Configuration_adv.h
+++ b/config/examples/FYSETC/F6_13/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Felix/Configuration_adv.h b/config/examples/Felix/Configuration_adv.h
index 0306d59382..62bbeb99d0 100644
--- a/config/examples/Felix/Configuration_adv.h
+++ b/config/examples/Felix/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/FlashForge/CreatorPro/Configuration_adv.h b/config/examples/FlashForge/CreatorPro/Configuration_adv.h
index 2c448b97c8..9cf659dfa7 100644
--- a/config/examples/FlashForge/CreatorPro/Configuration_adv.h
+++ b/config/examples/FlashForge/CreatorPro/Configuration_adv.h
@@ -2302,6 +2302,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/FolgerTech/i3-2020/Configuration_adv.h b/config/examples/FolgerTech/i3-2020/Configuration_adv.h
index faaa0d6571..b44e973bfb 100644
--- a/config/examples/FolgerTech/i3-2020/Configuration_adv.h
+++ b/config/examples/FolgerTech/i3-2020/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Formbot/Raptor/Configuration_adv.h b/config/examples/Formbot/Raptor/Configuration_adv.h
index 7fbc2f06c0..5e0bb4f712 100644
--- a/config/examples/Formbot/Raptor/Configuration_adv.h
+++ b/config/examples/Formbot/Raptor/Configuration_adv.h
@@ -2305,6 +2305,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Formbot/T_Rex_2+/Configuration_adv.h b/config/examples/Formbot/T_Rex_2+/Configuration_adv.h
index 44c88aff19..df2f8b38e8 100644
--- a/config/examples/Formbot/T_Rex_2+/Configuration_adv.h
+++ b/config/examples/Formbot/T_Rex_2+/Configuration_adv.h
@@ -2307,6 +2307,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Formbot/T_Rex_3/Configuration_adv.h b/config/examples/Formbot/T_Rex_3/Configuration_adv.h
index 14cb66423b..8ba7354e0f 100644
--- a/config/examples/Formbot/T_Rex_3/Configuration_adv.h
+++ b/config/examples/Formbot/T_Rex_3/Configuration_adv.h
@@ -2307,6 +2307,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Geeetech/A10/Configuration_adv.h b/config/examples/Geeetech/A10/Configuration_adv.h
index b0b4cad966..c71af2db68 100644
--- a/config/examples/Geeetech/A10/Configuration_adv.h
+++ b/config/examples/Geeetech/A10/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Geeetech/A10M/Configuration_adv.h b/config/examples/Geeetech/A10M/Configuration_adv.h
index c2c74d6718..c66386e834 100644
--- a/config/examples/Geeetech/A10M/Configuration_adv.h
+++ b/config/examples/Geeetech/A10M/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Geeetech/A20M/Configuration_adv.h b/config/examples/Geeetech/A20M/Configuration_adv.h
index 446204a065..f7a2bb6724 100644
--- a/config/examples/Geeetech/A20M/Configuration_adv.h
+++ b/config/examples/Geeetech/A20M/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Geeetech/MeCreator2/Configuration_adv.h b/config/examples/Geeetech/MeCreator2/Configuration_adv.h
index a29bab3847..3cb8545fe1 100644
--- a/config/examples/Geeetech/MeCreator2/Configuration_adv.h
+++ b/config/examples/Geeetech/MeCreator2/Configuration_adv.h
@@ -2302,6 +2302,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h b/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h
index b0b4cad966..c71af2db68 100644
--- a/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h	
+++ b/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h	
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h b/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h
index b0b4cad966..c71af2db68 100644
--- a/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h	
+++ b/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h	
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Infitary/i3-M508/Configuration_adv.h b/config/examples/Infitary/i3-M508/Configuration_adv.h
index 5f26ea253b..1f8a9f5773 100644
--- a/config/examples/Infitary/i3-M508/Configuration_adv.h
+++ b/config/examples/Infitary/i3-M508/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/JGAurora/A1/Configuration_adv.h b/config/examples/JGAurora/A1/Configuration_adv.h
index 49897c3cbb..301739e32e 100644
--- a/config/examples/JGAurora/A1/Configuration_adv.h
+++ b/config/examples/JGAurora/A1/Configuration_adv.h
@@ -2308,6 +2308,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/JGAurora/A5/Configuration_adv.h b/config/examples/JGAurora/A5/Configuration_adv.h
index 0925a2c32f..e3acecfb38 100644
--- a/config/examples/JGAurora/A5/Configuration_adv.h
+++ b/config/examples/JGAurora/A5/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/JGAurora/A5S/Configuration_adv.h b/config/examples/JGAurora/A5S/Configuration_adv.h
index 49897c3cbb..301739e32e 100644
--- a/config/examples/JGAurora/A5S/Configuration_adv.h
+++ b/config/examples/JGAurora/A5S/Configuration_adv.h
@@ -2308,6 +2308,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Malyan/M150/Configuration_adv.h b/config/examples/Malyan/M150/Configuration_adv.h
index 7ce934b383..92d8442bc6 100644
--- a/config/examples/Malyan/M150/Configuration_adv.h
+++ b/config/examples/Malyan/M150/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Malyan/M200/Configuration_adv.h b/config/examples/Malyan/M200/Configuration_adv.h
index f2755f7f1b..9d1b947717 100644
--- a/config/examples/Malyan/M200/Configuration_adv.h
+++ b/config/examples/Malyan/M200/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Micromake/C1/enhanced/Configuration_adv.h b/config/examples/Micromake/C1/enhanced/Configuration_adv.h
index d1439eaedd..27964f93fe 100644
--- a/config/examples/Micromake/C1/enhanced/Configuration_adv.h
+++ b/config/examples/Micromake/C1/enhanced/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Mks/Robin/Configuration_adv.h b/config/examples/Mks/Robin/Configuration_adv.h
index 0a50c1f9d6..9f608558af 100644
--- a/config/examples/Mks/Robin/Configuration_adv.h
+++ b/config/examples/Mks/Robin/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Mks/Sbase/Configuration_adv.h b/config/examples/Mks/Sbase/Configuration_adv.h
index 935d5d71f0..1f7586ebfc 100644
--- a/config/examples/Mks/Sbase/Configuration_adv.h
+++ b/config/examples/Mks/Sbase/Configuration_adv.h
@@ -2304,6 +2304,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/RapideLite/RL200/Configuration_adv.h b/config/examples/RapideLite/RL200/Configuration_adv.h
index fbef019136..f6dd9fc2e8 100644
--- a/config/examples/RapideLite/RL200/Configuration_adv.h
+++ b/config/examples/RapideLite/RL200/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/RigidBot/Configuration_adv.h b/config/examples/RigidBot/Configuration_adv.h
index 442467eb06..c5b5a1b31e 100644
--- a/config/examples/RigidBot/Configuration_adv.h
+++ b/config/examples/RigidBot/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/SCARA/Configuration_adv.h b/config/examples/SCARA/Configuration_adv.h
index ef063f2c2b..f2836f0c46 100644
--- a/config/examples/SCARA/Configuration_adv.h
+++ b/config/examples/SCARA/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h b/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h
index aa1a1b76ee..3feb4ed805 100644
--- a/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h
+++ b/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Sanguinololu/Configuration_adv.h b/config/examples/Sanguinololu/Configuration_adv.h
index 22aa92e7ba..64e4ab516f 100644
--- a/config/examples/Sanguinololu/Configuration_adv.h
+++ b/config/examples/Sanguinololu/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Tevo/Michelangelo/Configuration_adv.h b/config/examples/Tevo/Michelangelo/Configuration_adv.h
index d004daf425..27e3f0d3c5 100644
--- a/config/examples/Tevo/Michelangelo/Configuration_adv.h
+++ b/config/examples/Tevo/Michelangelo/Configuration_adv.h
@@ -2302,6 +2302,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Tevo/Tarantula Pro/Configuration_adv.h b/config/examples/Tevo/Tarantula Pro/Configuration_adv.h
index ba5e46d4fa..fc151b21ba 100755
--- a/config/examples/Tevo/Tarantula Pro/Configuration_adv.h	
+++ b/config/examples/Tevo/Tarantula Pro/Configuration_adv.h	
@@ -2299,6 +2299,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h
index 23c9d0f5ed..02ee750f69 100755
--- a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h	
+++ b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h	
@@ -2302,6 +2302,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h
index 23c9d0f5ed..02ee750f69 100755
--- a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h	
+++ b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h	
@@ -2302,6 +2302,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/TheBorg/Configuration_adv.h b/config/examples/TheBorg/Configuration_adv.h
index bee4c57bd6..fd633d785c 100644
--- a/config/examples/TheBorg/Configuration_adv.h
+++ b/config/examples/TheBorg/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/TinyBoy2/Configuration_adv.h b/config/examples/TinyBoy2/Configuration_adv.h
index a0ca9612e2..f18bd8758d 100644
--- a/config/examples/TinyBoy2/Configuration_adv.h
+++ b/config/examples/TinyBoy2/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Tronxy/X3A/Configuration_adv.h b/config/examples/Tronxy/X3A/Configuration_adv.h
index c624c462fc..2811cd83d9 100644
--- a/config/examples/Tronxy/X3A/Configuration_adv.h
+++ b/config/examples/Tronxy/X3A/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Tronxy/X5S-2E/Configuration_adv.h b/config/examples/Tronxy/X5S-2E/Configuration_adv.h
index 1c11cf298c..56ca3db093 100644
--- a/config/examples/Tronxy/X5S-2E/Configuration_adv.h
+++ b/config/examples/Tronxy/X5S-2E/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/UltiMachine/Archim1/Configuration_adv.h b/config/examples/UltiMachine/Archim1/Configuration_adv.h
index e120bc388f..b782d2e267 100644
--- a/config/examples/UltiMachine/Archim1/Configuration_adv.h
+++ b/config/examples/UltiMachine/Archim1/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/UltiMachine/Archim2/Configuration_adv.h b/config/examples/UltiMachine/Archim2/Configuration_adv.h
index b7653614e6..5d353bb3ef 100644
--- a/config/examples/UltiMachine/Archim2/Configuration_adv.h
+++ b/config/examples/UltiMachine/Archim2/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/VORONDesign/Configuration_adv.h b/config/examples/VORONDesign/Configuration_adv.h
index e9e8d4c965..a511a68bfe 100644
--- a/config/examples/VORONDesign/Configuration_adv.h
+++ b/config/examples/VORONDesign/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Velleman/K8200/Configuration_adv.h b/config/examples/Velleman/K8200/Configuration_adv.h
index 1baa3e3faa..fa295fe2fd 100644
--- a/config/examples/Velleman/K8200/Configuration_adv.h
+++ b/config/examples/Velleman/K8200/Configuration_adv.h
@@ -2316,6 +2316,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Velleman/K8400/Configuration_adv.h b/config/examples/Velleman/K8400/Configuration_adv.h
index 3d5f2c3177..7e2a1afbf8 100644
--- a/config/examples/Velleman/K8400/Configuration_adv.h
+++ b/config/examples/Velleman/K8400/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/WASP/PowerWASP/Configuration_adv.h b/config/examples/WASP/PowerWASP/Configuration_adv.h
index 155af52a8d..b1f2096a68 100644
--- a/config/examples/WASP/PowerWASP/Configuration_adv.h
+++ b/config/examples/WASP/PowerWASP/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Wanhao/Duplicator 6/Configuration_adv.h b/config/examples/Wanhao/Duplicator 6/Configuration_adv.h
index e2fd83c6bf..5827ec64af 100644
--- a/config/examples/Wanhao/Duplicator 6/Configuration_adv.h	
+++ b/config/examples/Wanhao/Duplicator 6/Configuration_adv.h	
@@ -2305,6 +2305,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h b/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h
index 49b6280199..136b3401d1 100644
--- a/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h	
+++ b/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h	
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/delta/Anycubic/Kossel/Configuration_adv.h b/config/examples/delta/Anycubic/Kossel/Configuration_adv.h
index ca1bab438e..c6a8cb5361 100644
--- a/config/examples/delta/Anycubic/Kossel/Configuration_adv.h
+++ b/config/examples/delta/Anycubic/Kossel/Configuration_adv.h
@@ -2305,6 +2305,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h b/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h
index 3338930799..385e28a763 100644
--- a/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h
+++ b/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h
@@ -2295,6 +2295,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h
index 3338930799..385e28a763 100644
--- a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h
+++ b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h
@@ -2295,6 +2295,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h b/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
index c9407721f9..9d1bb4bb2d 100644
--- a/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
+++ b/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
@@ -2305,6 +2305,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/delta/FLSUN/kossel/Configuration_adv.h b/config/examples/delta/FLSUN/kossel/Configuration_adv.h
index c9407721f9..9d1bb4bb2d 100644
--- a/config/examples/delta/FLSUN/kossel/Configuration_adv.h
+++ b/config/examples/delta/FLSUN/kossel/Configuration_adv.h
@@ -2305,6 +2305,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h b/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
index 08551f0c2f..077e3da4cc 100644
--- a/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
+++ b/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h
@@ -2305,6 +2305,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h b/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h
index cb09c62afe..51245109d5 100644
--- a/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h	
+++ b/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h	
@@ -2305,6 +2305,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/delta/MKS/SBASE/Configuration_adv.h b/config/examples/delta/MKS/SBASE/Configuration_adv.h
index ba381711fe..0cc3db7e4b 100644
--- a/config/examples/delta/MKS/SBASE/Configuration_adv.h
+++ b/config/examples/delta/MKS/SBASE/Configuration_adv.h
@@ -2305,6 +2305,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/delta/Tevo Little Monster/Configuration_adv.h b/config/examples/delta/Tevo Little Monster/Configuration_adv.h
index 4a6b2fa76d..7bb5af5d53 100644
--- a/config/examples/delta/Tevo Little Monster/Configuration_adv.h	
+++ b/config/examples/delta/Tevo Little Monster/Configuration_adv.h	
@@ -2305,6 +2305,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/delta/generic/Configuration_adv.h b/config/examples/delta/generic/Configuration_adv.h
index 08551f0c2f..077e3da4cc 100644
--- a/config/examples/delta/generic/Configuration_adv.h
+++ b/config/examples/delta/generic/Configuration_adv.h
@@ -2305,6 +2305,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/delta/kossel_mini/Configuration_adv.h b/config/examples/delta/kossel_mini/Configuration_adv.h
index 08551f0c2f..077e3da4cc 100644
--- a/config/examples/delta/kossel_mini/Configuration_adv.h
+++ b/config/examples/delta/kossel_mini/Configuration_adv.h
@@ -2305,6 +2305,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/delta/kossel_xl/Configuration_adv.h b/config/examples/delta/kossel_xl/Configuration_adv.h
index 91f0d22bd6..053cc6da0c 100644
--- a/config/examples/delta/kossel_xl/Configuration_adv.h
+++ b/config/examples/delta/kossel_xl/Configuration_adv.h
@@ -2305,6 +2305,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/gCreate/gMax1.5+/Configuration_adv.h b/config/examples/gCreate/gMax1.5+/Configuration_adv.h
index d22564a94b..415d3dd521 100644
--- a/config/examples/gCreate/gMax1.5+/Configuration_adv.h
+++ b/config/examples/gCreate/gMax1.5+/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/makibox/Configuration_adv.h b/config/examples/makibox/Configuration_adv.h
index 03ea4f204f..d4fe552ef5 100644
--- a/config/examples/makibox/Configuration_adv.h
+++ b/config/examples/makibox/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/tvrrug/Round2/Configuration_adv.h b/config/examples/tvrrug/Round2/Configuration_adv.h
index e8acf8217b..c6d870990b 100644
--- a/config/examples/tvrrug/Round2/Configuration_adv.h
+++ b/config/examples/tvrrug/Round2/Configuration_adv.h
@@ -2303,6 +2303,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *
diff --git a/config/examples/wt150/Configuration_adv.h b/config/examples/wt150/Configuration_adv.h
index e6a6e7039b..5a7338b67c 100644
--- a/config/examples/wt150/Configuration_adv.h
+++ b/config/examples/wt150/Configuration_adv.h
@@ -2304,6 +2304,13 @@
   //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
 #endif
 
+/**
+ * Startup commands
+ *
+ * Execute certain G-code commands immediately after power-on.
+ */
+//#define STARTUP_COMMANDS "M17 Z"
+
 /**
  * G-code Macros
  *