diff --git a/config/examples/ADIMLab/_Bootscreen.h b/config/examples/ADIMLab/Gantry v1/_Bootscreen.h similarity index 100% rename from config/examples/ADIMLab/_Bootscreen.h rename to config/examples/ADIMLab/Gantry v1/_Bootscreen.h diff --git a/config/examples/ADIMLab/Gantry v2/_Bootscreen.h b/config/examples/ADIMLab/Gantry v2/_Bootscreen.h new file mode 100644 index 0000000000..ebb0ad9a81 --- /dev/null +++ b/config/examples/ADIMLab/Gantry v2/_Bootscreen.h @@ -0,0 +1,86 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/** + * Made with Marlin Bitmap Converter + * http://marlinfw.org/tools/u8glib/converter.html + */ +#define CUSTOM_BOOTSCREEN_BMPWIDTH 88 + +const unsigned char custom_start_bmp[] PROGMEM = { + B00000000,B00000000,B00000000,B00001111,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B00000000,B00000000,B00000000,B00111111,B11111000,B00000000,B01000000,B00000000,B00000000,B00000000,B00000000, + B00000000,B00000000,B00011110,B01111111,B11111111,B00000000,B10000100,B00000000,B00000000,B00000000,B00000000, + B00000000,B00000000,B00111111,B11111111,B11111111,B11111111,B00000100,B00000000,B00000000,B00000000,B00000000, + B00000000,B00000000,B00111111,B11111111,B11111111,B11111110,B00001100,B00000000,B00000000,B00000000,B00000000, + B00000000,B00000000,B01111111,B11111111,B11111111,B11110000,B00001000,B00000000,B00000000,B00000000,B00000000, + B00000000,B00000000,B00001111,B11111111,B11100000,B00000000,B00011000,B00000000,B00000000,B00000000,B00000000, + B00000000,B00000000,B00000000,B11111111,B11100011,B10000000,B00111000,B00000000,B00000000,B00000000,B00000000, + B00000000,B00000000,B00010011,B11111111,B11100001,B10000000,B01111000,B00000000,B00000000,B00000000,B00000000, + B00000000,B00000000,B00011111,B10001111,B11100011,B10000000,B11110000,B00000000,B00000000,B00000000,B00000000, + B00000000,B00000000,B00011110,B00001111,B11111111,B10000001,B11110000,B00000000,B00000000,B00000000,B00000000, + B00000000,B00000000,B00000110,B00011111,B11111111,B10000111,B11100000,B00000000,B00000000,B00000000,B00000000, + B00000000,B00000000,B00000000,B11111111,B11111110,B00001111,B11100000,B00000000,B00000000,B00000000,B00000000, + B00000000,B00000000,B00000111,B11111111,B11110000,B01111111,B11000000,B00000000,B00000000,B00000000,B00000000, + B00000000,B00000000,B00001111,B11111100,B00000011,B11111111,B10000000,B00000000,B00000000,B00000000,B00000000, + B00000000,B00000000,B00011111,B11000000,B11111111,B11111111,B00000000,B00000000,B00000000,B00000000,B00000000, + B00000000,B00000000,B00111110,B00011111,B11111111,B11111110,B00111111,B11000000,B00000000,B00000000,B00000000, + B00000000,B00000000,B01111100,B11111111,B11111111,B11111100,B00001111,B11100000,B00000000,B00000000,B00000000, + B00000000,B00000000,B11111001,B11111111,B11111111,B11110000,B00001111,B11110000,B00000000,B00000000,B00000000, + B00000000,B00000000,B11110011,B11111111,B11111111,B11111000,B00011111,B11111000,B00000000,B00000000,B00000000, + B00000000,B00000000,B11100111,B11111111,B11111111,B11111111,B11111111,B11111100,B00000000,B00000000,B00000000, + B00000000,B00000001,B11101111,B11111111,B11111111,B11111111,B11111111,B11111110,B00000000,B00000000,B00000000, + B00000000,B00000001,B11101111,B11111110,B00001111,B11111111,B11111111,B11101111,B10000000,B00000000,B00000000, + B00000000,B00000001,B11001111,B11110000,B00000001,B11111111,B11111111,B11110011,B11111000,B00000000,B00000000, + B00000000,B00000000,B11101111,B11100000,B00000000,B11111111,B11111111,B11111000,B01100000,B00000000,B00000000, + B00000000,B00000000,B11101111,B11100000,B00000000,B00111111,B11111111,B11111000,B00000000,B00000000,B00000000, + B00000000,B00000000,B11101111,B11000000,B00000000,B00011111,B11111111,B11111000,B00000000,B00000000,B00000000, + B00000000,B00000000,B01100111,B11100100,B00000000,B00001111,B11111111,B11111100,B00000000,B00000000,B00000000, + B00000000,B00000000,B00110011,B11111100,B00000000,B00000111,B11111111,B11111100,B00000000,B00000000,B00000000, + B00000000,B00000000,B00011001,B11111100,B00000000,B00000011,B11100000,B11111100,B00000000,B00000000,B00000000, + B00000000,B00000000,B00001100,B01111000,B00000000,B00000001,B11100000,B00111100,B00000000,B00000000,B00000000, + B00000000,B00000000,B00000111,B00000000,B00000000,B00000000,B01110000,B00011100,B00000000,B00000000,B00000000, + B00000000,B00000000,B00000011,B10000000,B00000000,B00000000,B00000000,B00001110,B00000000,B00000000,B00000000, + B00000000,B00000000,B00000001,B11100000,B00000000,B00000000,B00000000,B00001111,B00000000,B00000000,B00000000, + B00000000,B00000000,B00000001,B11110000,B00000000,B00000000,B00000000,B00000111,B00000000,B00000000,B00000000, + B00000000,B00000000,B00000001,B11111000,B00000000,B00000000,B00000000,B00000111,B10000000,B00000000,B00000000, + B00000000,B00000000,B00000001,B11111100,B00000000,B00000000,B00000000,B00000111,B11000000,B00000000,B00000000, + B00000000,B00000000,B00000011,B11111100,B00000000,B00000000,B00000000,B00001111,B11000000,B00000000,B00000000, + B00000000,B00000000,B00000111,B11111100,B00000000,B00000000,B00000000,B00001111,B11100000,B00000000,B00000000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B00000111,B10000001,B11111111,B10000111,B10011111,B00000111,B10011110,B00000000,B00000000,B00111000,B00000000, + B00000111,B10000001,B11111111,B11000011,B10011111,B00000111,B10001110,B00000000,B00000000,B00111000,B00000000, + B00000111,B10000001,B11000011,B11100011,B10011111,B00000111,B10001110,B00000000,B00000000,B00111000,B00000000, + B00001111,B11000001,B11000000,B11100011,B10011111,B10001111,B10001110,B00000000,B00111100,B00111011,B00000000, + B00001111,B11000001,B11000000,B11100011,B10011111,B10001111,B10001110,B00000000,B11111110,B00111111,B10000000, + B00011101,B11000001,B11000000,B01110011,B10011111,B10011111,B10001110,B00000000,B11111111,B00111111,B10000000, + B00011100,B11100001,B11000000,B01110011,B10011101,B11011011,B10001110,B00000000,B01101111,B00111011,B11000000, + B00011100,B11100001,B11000000,B01110011,B10011101,B11111011,B10001110,B00000000,B00111111,B00111011,B11000000, + B00111111,B11110001,B11000000,B11100011,B10011100,B11111011,B10001110,B00000000,B11111111,B00111011,B11000000, + B00111111,B11110001,B11000000,B11100011,B10011100,B11110011,B10001110,B00000000,B11101111,B00111011,B11000000, + B01111000,B01110001,B11000001,B11100011,B10011100,B11110011,B10001110,B00000001,B11101111,B00111011,B11000000, + B01110000,B01111001,B11111111,B11000011,B10011100,B01100011,B10001111,B11111111,B11101111,B00111111,B10000000, + B01110000,B00111001,B11111111,B10000011,B10011100,B01100011,B10001111,B11111110,B11110111,B00111111,B10000000, + B11110000,B01111101,B11111111,B00000111,B10011110,B00000011,B11011111,B11111100,B01100111,B00100111,B00000000 +}; diff --git a/config/examples/Felix/Configuration_adv.h b/config/examples/Felix/DUAL/Configuration_adv.h similarity index 100% rename from config/examples/Felix/Configuration_adv.h rename to config/examples/Felix/DUAL/Configuration_adv.h diff --git a/config/examples/Felix/README.md b/config/examples/Felix/DUAL/README.md similarity index 100% rename from config/examples/Felix/README.md rename to config/examples/Felix/DUAL/README.md diff --git a/config/examples/Felix/Configuration.h b/config/examples/Felix/Single/Configuration.h similarity index 100% rename from config/examples/Felix/Configuration.h rename to config/examples/Felix/Single/Configuration.h diff --git a/config/examples/Felix/Single/Configuration_adv.h b/config/examples/Felix/Single/Configuration_adv.h new file mode 100644 index 0000000000..5ef7cf106f --- /dev/null +++ b/config/examples/Felix/Single/Configuration_adv.h @@ -0,0 +1,2764 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/** + * Configuration_adv.h + * + * Advanced settings. + * Only change these if you know exactly what you're doing. + * Some of these settings can damage your printer if improperly set! + * + * Basic settings can be found in Configuration.h + * + */ +#define CONFIGURATION_ADV_H_VERSION 020000 + +// @section temperature + +//=========================================================================== +//=============================Thermal Settings ============================ +//=========================================================================== + +// +// Custom Thermistor 1000 parameters +// +#if TEMP_SENSOR_0 == 1000 + #define HOTEND0_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND0_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND0_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_1 == 1000 + #define HOTEND1_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND1_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND1_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_2 == 1000 + #define HOTEND2_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND2_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND2_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_3 == 1000 + #define HOTEND3_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND3_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND3_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_4 == 1000 + #define HOTEND4_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND4_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND4_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_5 == 1000 + #define HOTEND5_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND5_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND5_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_BED == 1000 + #define BED_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define BED_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define BED_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_CHAMBER == 1000 + #define CHAMBER_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define CHAMBER_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define CHAMBER_BETA 3950 // Beta value +#endif + +// +// Hephestos 2 24V heated bed upgrade kit. +// https://store.bq.com/en/heated-bed-kit-hephestos2 +// +//#define HEPHESTOS2_HEATED_BED_KIT +#if ENABLED(HEPHESTOS2_HEATED_BED_KIT) + #undef TEMP_SENSOR_BED + #define TEMP_SENSOR_BED 70 + #define HEATER_BED_INVERTING true +#endif + +/** + * Heated Chamber settings + */ +#if TEMP_SENSOR_CHAMBER + #define CHAMBER_MINTEMP 5 + #define CHAMBER_MAXTEMP 60 + #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target + //#define CHAMBER_LIMIT_SWITCHING + //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin + //#define HEATER_CHAMBER_INVERTING false +#endif + +#if DISABLED(PIDTEMPBED) + #define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control + #if ENABLED(BED_LIMIT_SWITCHING) + #define BED_HYSTERESIS 2 // Only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS + #endif +#endif + +/** + * Thermal Protection provides additional protection to your printer from damage + * and fire. Marlin always includes safe min and max temperature ranges which + * protect against a broken or disconnected thermistor wire. + * + * The issue: If a thermistor falls out, it will report the much lower + * temperature of the air in the room, and the the firmware will keep + * the heater on. + * + * The solution: Once the temperature reaches the target, start observing. + * If the temperature stays too far below the target (hysteresis) for too + * long (period), the firmware will halt the machine as a safety precaution. + * + * If you get false positives for "Thermal Runaway", increase + * THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD + */ +#if ENABLED(THERMAL_PROTECTION_HOTENDS) + #define THERMAL_PROTECTION_PERIOD 40 // Seconds + #define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius + + //#define ADAPTIVE_FAN_SLOWING // Slow part cooling fan if temperature drops + #if BOTH(ADAPTIVE_FAN_SLOWING, PIDTEMP) + //#define NO_FAN_SLOWING_IN_PID_TUNING // Don't slow fan speed during M303 + #endif + + /** + * Whenever an M104, M109, or M303 increases the target temperature, the + * firmware will wait for the WATCH_TEMP_PERIOD to expire. If the temperature + * hasn't increased by WATCH_TEMP_INCREASE degrees, the machine is halted and + * requires a hard reset. This test restarts with any M104/M109/M303, but only + * if the current temperature is far enough below the target for a reliable + * test. + * + * If you get false positives for "Heating failed", increase WATCH_TEMP_PERIOD + * and/or decrease WATCH_TEMP_INCREASE. WATCH_TEMP_INCREASE should not be set + * below 2. + */ + #define WATCH_TEMP_PERIOD 20 // Seconds + #define WATCH_TEMP_INCREASE 2 // Degrees Celsius +#endif + +/** + * Thermal Protection parameters for the bed are just as above for hotends. + */ +#if ENABLED(THERMAL_PROTECTION_BED) + #define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds + #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius + + /** + * As described above, except for the bed (M140/M190/M303). + */ + #define WATCH_BED_TEMP_PERIOD 60 // Seconds + #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius +#endif + +/** + * Thermal Protection parameters for the heated chamber. + */ +#if ENABLED(THERMAL_PROTECTION_CHAMBER) + #define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds + #define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius + + /** + * Heated chamber watch settings (M141/M191). + */ + #define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds + #define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius +#endif + +#if ENABLED(PIDTEMP) + // Add an experimental additional term to the heater power, proportional to the extrusion speed. + // A well-chosen Kc value should add just enough power to melt the increased material volume. + //#define PID_EXTRUSION_SCALING + #if ENABLED(PID_EXTRUSION_SCALING) + #define DEFAULT_Kc (100) //heating power=Kc*(e_speed) + #define LPQ_MAX_LEN 50 + #endif +#endif + +/** + * Automatic Temperature: + * The hotend target temperature is calculated by all the buffered lines of gcode. + * The maximum buffered steps/sec of the extruder motor is called "se". + * Start autotemp mode with M109 S B F + * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by + * mintemp and maxtemp. Turn this off by executing M109 without F* + * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp. + * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode + */ +#define AUTOTEMP +#if ENABLED(AUTOTEMP) + #define AUTOTEMP_OLDWEIGHT 0.98 +#endif + +// Show extra position information with 'M114 D' +//#define M114_DETAIL + +// Show Temperature ADC value +// Enable for M105 to include ADC values read from temperature sensors. +//#define SHOW_TEMP_ADC_VALUES + +/** + * High Temperature Thermistor Support + * + * Thermistors able to support high temperature tend to have a hard time getting + * good readings at room and lower temperatures. This means HEATER_X_RAW_LO_TEMP + * will probably be caught when the heating element first turns on during the + * preheating process, which will trigger a min_temp_error as a safety measure + * and force stop everything. + * To circumvent this limitation, we allow for a preheat time (during which, + * min_temp_error won't be triggered) and add a min_temp buffer to handle + * aberrant readings. + * + * If you want to enable this feature for your hotend thermistor(s) + * uncomment and set values > 0 in the constants below + */ + +// The number of consecutive low temperature errors that can occur +// before a min_temp_error is triggered. (Shouldn't be more than 10.) +//#define MAX_CONSECUTIVE_LOW_TEMPERATURE_ERROR_ALLOWED 0 + +// The number of milliseconds a hotend will preheat before starting to check +// the temperature. This value should NOT be set to the time it takes the +// hot end to reach the target temperature, but the time it takes to reach +// the minimum temperature your thermistor can read. The lower the better/safer. +// This shouldn't need to be more than 30 seconds (30000) +//#define MILLISECONDS_PREHEAT_TIME 0 + +// @section extruder + +// Extruder runout prevention. +// If the machine is idle and the temperature over MINTEMP +// then extrude some filament every couple of SECONDS. +//#define EXTRUDER_RUNOUT_PREVENT +#if ENABLED(EXTRUDER_RUNOUT_PREVENT) + #define EXTRUDER_RUNOUT_MINTEMP 190 + #define EXTRUDER_RUNOUT_SECONDS 30 + #define EXTRUDER_RUNOUT_SPEED 1500 // (mm/m) + #define EXTRUDER_RUNOUT_EXTRUDE 5 // (mm) +#endif + +// @section temperature + +// Calibration for AD595 / AD8495 sensor to adjust temperature measurements. +// The final temperature is calculated as (measuredTemp * GAIN) + OFFSET. +#define TEMP_SENSOR_AD595_OFFSET 0.0 +#define TEMP_SENSOR_AD595_GAIN 1.0 +#define TEMP_SENSOR_AD8495_OFFSET 0.0 +#define TEMP_SENSOR_AD8495_GAIN 1.0 + +/** + * Controller Fan + * To cool down the stepper drivers and MOSFETs. + * + * The fan will turn on automatically whenever any stepper is enabled + * and turn off after a set period after all steppers are turned off. + */ +//#define USE_CONTROLLER_FAN +#if ENABLED(USE_CONTROLLER_FAN) + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled + #define CONTROLLERFAN_SPEED 255 // 255 == full speed + //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled +#endif + +// When first starting the main fan, run it at full speed for the +// given number of milliseconds. This gets the fan spinning reliably +// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) +//#define FAN_KICKSTART_TIME 100 + +/** + * PWM Fan Scaling + * + * Define the min/max speeds for PWM fans (as set with M106). + * + * With these options the M106 0-255 value range is scaled to a subset + * to ensure that the fan has enough power to spin, or to run lower + * current fans with higher current. (e.g., 5V/12V fans with 12V/24V) + * Value 0 always turns off the fan. + * + * Define one or both of these to override the default 0-255 range. + */ +//#define FAN_MIN_PWM 50 +//#define FAN_MAX_PWM 128 + +/** + * FAST PWM FAN Settings + * + * Use to change the FAST FAN PWM frequency (if enabled in Configuration.h) + * Combinations of PWM Modes, prescale values and TOP resolutions are used internally to produce a + * frequency as close as possible to the desired frequency. + * + * FAST_PWM_FAN_FREQUENCY [undefined by default] + * Set this to your desired frequency. + * If left undefined this defaults to F = F_CPU/(2*255*1) + * ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers + * These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required + * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior. + * + * USE_OCR2A_AS_TOP [undefined by default] + * Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2: + * 16MHz MCUs: [62.5KHz, 31.4KHz (default), 7.8KHz, 3.92KHz, 1.95KHz, 977Hz, 488Hz, 244Hz, 60Hz, 122Hz, 30Hz] + * 20MHz MCUs: [78.1KHz, 39.2KHz (default), 9.77KHz, 4.9KHz, 2.44KHz, 1.22KHz, 610Hz, 305Hz, 153Hz, 76Hz, 38Hz] + * A greater range can be achieved by enabling USE_OCR2A_AS_TOP. But note that this option blocks the use of + * PWM on pin OC2A. Only use this option if you don't need PWM on 0C2A. (Check your schematic.) + * USE_OCR2A_AS_TOP sacrifices duty cycle control resolution to achieve this broader range of frequencies. + */ +#if ENABLED(FAST_PWM_FAN) + //#define FAST_PWM_FAN_FREQUENCY 31400 + //#define USE_OCR2A_AS_TOP +#endif + +// @section extruder + +/** + * Extruder cooling fans + * + * Extruder auto fans automatically turn on when their extruders' + * temperatures go above EXTRUDER_AUTO_FAN_TEMPERATURE. + * + * Your board's pins file specifies the recommended pins. Override those here + * or set to -1 to disable completely. + * + * Multiple extruders can be assigned to the same pin in which case + * the fan will turn on when any selected extruder is above the threshold. + */ +#define E0_AUTO_FAN_PIN -1 +#define E1_AUTO_FAN_PIN -1 +#define E2_AUTO_FAN_PIN -1 +#define E3_AUTO_FAN_PIN -1 +#define E4_AUTO_FAN_PIN -1 +#define E5_AUTO_FAN_PIN -1 +#define CHAMBER_AUTO_FAN_PIN -1 + +#define EXTRUDER_AUTO_FAN_TEMPERATURE 50 +#define EXTRUDER_AUTO_FAN_SPEED 255 // 255 == full speed +#define CHAMBER_AUTO_FAN_TEMPERATURE 30 +#define CHAMBER_AUTO_FAN_SPEED 255 + +/** + * Part-Cooling Fan Multiplexer + * + * This feature allows you to digitally multiplex the fan output. + * The multiplexer is automatically switched at tool-change. + * Set FANMUX[012]_PINs below for up to 2, 4, or 8 multiplexed fans. + */ +#define FANMUX0_PIN -1 +#define FANMUX1_PIN -1 +#define FANMUX2_PIN -1 + +/** + * M355 Case Light on-off / brightness + */ +//#define CASE_LIGHT_ENABLE +#if ENABLED(CASE_LIGHT_ENABLE) + //#define CASE_LIGHT_PIN 4 // Override the default pin if needed + #define INVERT_CASE_LIGHT false // Set true if Case Light is ON when pin is LOW + #define CASE_LIGHT_DEFAULT_ON true // Set default power-up state on + #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105 // Set default power-up brightness (0-255, requires PWM pin) + //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu + //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. + //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) + #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } + #endif +#endif + +// @section homing + +// If you want endstops to stay on (by default) even when not homing +// enable this option. Override at any time with M120, M121. +//#define ENDSTOPS_ALWAYS_ON_DEFAULT + +// @section extras + +//#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats. + +// Employ an external closed loop controller. Override pins here if needed. +//#define EXTERNAL_CLOSED_LOOP_CONTROLLER +#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER) + //#define CLOSED_LOOP_ENABLE_PIN -1 + //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1 +#endif + +/** + * Dual Steppers / Dual Endstops + * + * This section will allow you to use extra E drivers to drive a second motor for X, Y, or Z axes. + * + * For example, set X_DUAL_STEPPER_DRIVERS setting to use a second motor. If the motors need to + * spin in opposite directions set INVERT_X2_VS_X_DIR. If the second motor needs its own endstop + * set X_DUAL_ENDSTOPS. This can adjust for "racking." Use X2_USE_ENDSTOP to set the endstop plug + * that should be used for the second endstop. Extra endstops will appear in the output of 'M119'. + * + * Use X_DUAL_ENDSTOP_ADJUSTMENT to adjust for mechanical imperfection. After homing both motors + * this offset is applied to the X2 motor. To find the offset home the X axis, and measure the error + * in X2. Dual endstop offsets can be set at runtime with 'M666 X Y Z'. + */ + +//#define X_DUAL_STEPPER_DRIVERS +#if ENABLED(X_DUAL_STEPPER_DRIVERS) + #define INVERT_X2_VS_X_DIR true // Set 'true' if X motors should rotate in opposite directions + //#define X_DUAL_ENDSTOPS + #if ENABLED(X_DUAL_ENDSTOPS) + #define X2_USE_ENDSTOP _XMAX_ + #define X_DUAL_ENDSTOPS_ADJUSTMENT 0 + #endif +#endif + +//#define Y_DUAL_STEPPER_DRIVERS +#if ENABLED(Y_DUAL_STEPPER_DRIVERS) + #define INVERT_Y2_VS_Y_DIR true // Set 'true' if Y motors should rotate in opposite directions + //#define Y_DUAL_ENDSTOPS + #if ENABLED(Y_DUAL_ENDSTOPS) + #define Y2_USE_ENDSTOP _YMAX_ + #define Y_DUAL_ENDSTOPS_ADJUSTMENT 0 + #endif +#endif + +//#define Z_DUAL_STEPPER_DRIVERS +#if ENABLED(Z_DUAL_STEPPER_DRIVERS) + //#define Z_DUAL_ENDSTOPS + #if ENABLED(Z_DUAL_ENDSTOPS) + #define Z2_USE_ENDSTOP _XMAX_ + #define Z_DUAL_ENDSTOPS_ADJUSTMENT 0 + #endif +#endif + +//#define Z_TRIPLE_STEPPER_DRIVERS +#if ENABLED(Z_TRIPLE_STEPPER_DRIVERS) + //#define Z_TRIPLE_ENDSTOPS + #if ENABLED(Z_TRIPLE_ENDSTOPS) + #define Z2_USE_ENDSTOP _XMAX_ + #define Z3_USE_ENDSTOP _YMAX_ + #define Z_TRIPLE_ENDSTOPS_ADJUSTMENT2 0 + #define Z_TRIPLE_ENDSTOPS_ADJUSTMENT3 0 + #endif +#endif + +/** + * Dual X Carriage + * + * This setup has two X carriages that can move independently, each with its own hotend. + * The carriages can be used to print an object with two colors or materials, or in + * "duplication mode" it can print two identical or X-mirrored objects simultaneously. + * The inactive carriage is parked automatically to prevent oozing. + * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. + * By default the X2 stepper is assigned to the first unused E plug on the board. + * + * The following Dual X Carriage modes can be selected with M605 S: + * + * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel + * results as long as it supports dual X-carriages. (M605 S0) + * + * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so + * that additional slicer support is not required. (M605 S1) + * + * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with + * the first X-carriage and extruder, to print 2 copies of the same object at the same time. + * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and + * follow with M605 S2 to initiate duplicated movement. + * + * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates + * the movement of the first except the second extruder is reversed in the X axis. + * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and + * follow with M605 S3 to initiate mirrored movement. + */ +//#define DUAL_X_CARRIAGE +#if ENABLED(DUAL_X_CARRIAGE) + #define X1_MIN_POS X_MIN_POS // Set to X_MIN_POS + #define X1_MAX_POS X_BED_SIZE // Set a maximum so the first X-carriage can't hit the parked second X-carriage + #define X2_MIN_POS 80 // Set a minimum to ensure the second X-carriage can't hit the parked first X-carriage + #define X2_MAX_POS 353 // Set this to the distance between toolheads when both heads are homed + #define X2_HOME_DIR 1 // Set to 1. The second X-carriage always homes to the maximum endstop position + #define X2_HOME_POS X2_MAX_POS // Default X2 home position. Set to X2_MAX_POS. + // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software + // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops + // without modifying the firmware (through the "M218 T1 X???" command). + // Remember: you should set the second extruder x-offset to 0 in your slicer. + + // This is the default power-up mode which can be later using M605. + #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_AUTO_PARK_MODE + + // Default x offset in duplication mode (typically set to half print bed width) + #define DEFAULT_DUPLICATION_X_OFFSET 100 + +#endif // DUAL_X_CARRIAGE + +// Activate a solenoid on the active extruder with M380. Disable all with M381. +// Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid. +//#define EXT_SOLENOID + +// @section homing + +// Homing hits each endstop, retracts by these distances, then does a slower bump. +#define X_HOME_BUMP_MM 5 +#define Y_HOME_BUMP_MM 5 +#define Z_HOME_BUMP_MM 3 +#define HOMING_BUMP_DIVISOR { 2, 2, 4 } // Re-Bump Speed Divisor (Divides the Homing Feedrate) +//#define QUICK_HOME // If homing includes X and Y, do a diagonal move initially +//#define HOMING_BACKOFF_MM { 2, 2, 2 } // (mm) Move away from the endstops after homing + +// When G28 is called, this option will make Y home before X +//#define HOME_Y_BEFORE_X + +// Enable this if X or Y can't home without homing the other axis first. +//#define CODEPENDENT_XY_HOMING + +#if ENABLED(BLTOUCH) + /** + * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES + * Do not activate settings that the probe might not understand. Clones might misunderstand + * advanced commands. + * + * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then + * check the wiring of the BROWN, RED and ORANGE wires. + * + * Note: If the trigger signal of your probe is not being recognized, it has been very often + * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable" + * like they would be with a real switch. So please check the wiring first. + * + * Settings for all BLTouch and clone probes: + */ + + // Safety: The probe needs time to recognize the command. + // Minimum command delay (ms). Enable and increase if needed. + //#define BLTOUCH_DELAY 500 + + /** + * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones: + */ + + // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful + // in special cases, like noisy or filtered input configurations. + //#define BLTOUCH_FORCE_SW_MODE + + /** + * Settings for BLTouch Smart 3.0 and 3.1 + * Summary: + * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes + * - High-Speed mode + * - Disable LCD voltage options + */ + + /** + * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller! + * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup. + * If disabled, OD mode is the hard-coded default on 3.0 + * On startup, Marlin will compare its eeprom to this vale. If the selected mode + * differs, a mode set eeprom write will be completed at initialization. + * Use the option below to force an eeprom write to a V3.1 probe regardless. + */ + //#define BLTOUCH_SET_5V_MODE + + /** + * Safety: Activate if connecting a probe with an unknown voltage mode. + * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0 + * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write ) + * To preserve the life of the probe, use this once then turn it off and re-flash. + */ + //#define BLTOUCH_FORCE_MODE_SET + + /** + * Use "HIGH SPEED" mode for probing. + * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems. + * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function + * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state. + */ + //#define BLTOUCH_HS_MODE + + // Safety: Enable voltage mode settings in the LCD menu. + //#define BLTOUCH_LCD_VOLTAGE_MENU + +#endif // BLTOUCH + +/** + * Z Steppers Auto-Alignment + * Add the G34 command to align multiple Z steppers using a bed probe. + */ +//#define Z_STEPPER_AUTO_ALIGN +#if ENABLED(Z_STEPPER_AUTO_ALIGN) + // Define probe X and Y positions for Z1, Z2 [, Z3] + #define Z_STEPPER_ALIGN_XY { { 10, 290 }, { 150, 10 }, { 290, 290 } } // Set number of iterations to align + #define Z_STEPPER_ALIGN_ITERATIONS 3 + // Enable to restore leveling setup after operation + #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + + // Use the amplification factor to de-/increase correction step. + // In case the stepper (spindle) position is further out than the test point + // Use a value > 1. NOTE: This may cause instability + #define Z_STEPPER_ALIGN_AMP 1.0 + // Stop criterion. If the accuracy is better than this stop iterating early + #define Z_STEPPER_ALIGN_ACC 0.02 +#endif + +// @section motion + +#define AXIS_RELATIVE_MODES { false, false, false, false } + +// Add a Duplicate option for well-separated conjoined nozzles +//#define MULTI_NOZZLE_DUPLICATION + +// By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step. +#define INVERT_X_STEP_PIN false +#define INVERT_Y_STEP_PIN false +#define INVERT_Z_STEP_PIN false +#define INVERT_E_STEP_PIN false + +// Default stepper release if idle. Set to 0 to deactivate. +// Steppers will shut down DEFAULT_STEPPER_DEACTIVE_TIME seconds after the last move when DISABLE_INACTIVE_? is true. +// Time can be set by M18 and M84. +#define DEFAULT_STEPPER_DEACTIVE_TIME 60 +#define DISABLE_INACTIVE_X true +#define DISABLE_INACTIVE_Y true +#define DISABLE_INACTIVE_Z true // Set to false if the nozzle will fall down on your printed part when print has finished. +#define DISABLE_INACTIVE_E true + +#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate +#define DEFAULT_MINTRAVELFEEDRATE 0.0 + +//#define HOME_AFTER_DEACTIVATE // Require rehoming after steppers are deactivated + +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) + +// If defined the movements slow down when the look ahead buffer is only half full +#define SLOWDOWN + +// Frequency limit +// See nophead's blog for more info +// Not working O +//#define XY_FREQUENCY_LIMIT 15 + +// Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end +// of the buffer and all stops. This should not be much greater than zero and should only be changed +// if unwanted behavior is observed on a user's machine when running at very slow speeds. +#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s) + +// +// Backlash Compensation +// Adds extra movement to axes on direction-changes to account for backlash. +// +//#define BACKLASH_COMPENSATION +#if ENABLED(BACKLASH_COMPENSATION) + // Define values for backlash distance and correction. + // If BACKLASH_GCODE is enabled these values are the defaults. + #define BACKLASH_DISTANCE_MM { 0, 0, 0 } // (mm) + #define BACKLASH_CORRECTION 0.0 // 0.0 = no correction; 1.0 = full correction + + // Set BACKLASH_SMOOTHING_MM to spread backlash correction over multiple segments + // to reduce print artifacts. (Enabling this is costly in memory and computation!) + //#define BACKLASH_SMOOTHING_MM 3 // (mm) + + // Add runtime configuration and tuning of backlash values (M425) + //#define BACKLASH_GCODE + + #if ENABLED(BACKLASH_GCODE) + // Measure the Z backlash when probing (G29) and set with "M425 Z" + #define MEASURE_BACKLASH_WHEN_PROBING + + #if ENABLED(MEASURE_BACKLASH_WHEN_PROBING) + // When measuring, the probe will move up to BACKLASH_MEASUREMENT_LIMIT + // mm away from point of contact in BACKLASH_MEASUREMENT_RESOLUTION + // increments while checking for the contact to be broken. + #define BACKLASH_MEASUREMENT_LIMIT 0.5 // (mm) + #define BACKLASH_MEASUREMENT_RESOLUTION 0.005 // (mm) + #define BACKLASH_MEASUREMENT_FEEDRATE Z_PROBE_SPEED_SLOW // (mm/m) + #endif + #endif +#endif + +/** + * Automatic backlash, position and hotend offset calibration + * + * Enable G425 to run automatic calibration using an electrically- + * conductive cube, bolt, or washer mounted on the bed. + * + * G425 uses the probe to touch the top and sides of the calibration object + * on the bed and measures and/or correct positional offsets, axis backlash + * and hotend offsets. + * + * Note: HOTEND_OFFSET and CALIBRATION_OBJECT_CENTER must be set to within + * ±5mm of true values for G425 to succeed. + */ +//#define CALIBRATION_GCODE +#if ENABLED(CALIBRATION_GCODE) + + #define CALIBRATION_MEASUREMENT_RESOLUTION 0.01 // mm + + #define CALIBRATION_FEEDRATE_SLOW 60 // mm/m + #define CALIBRATION_FEEDRATE_FAST 1200 // mm/m + #define CALIBRATION_FEEDRATE_TRAVEL 3000 // mm/m + + // The following parameters refer to the conical section of the nozzle tip. + #define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm + #define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm + + // Uncomment to enable reporting (required for "G425 V", but consumes PROGMEM). + //#define CALIBRATION_REPORTING + + // The true location and dimension the cube/bolt/washer on the bed. + #define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // mm + #define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // mm + + // Comment out any sides which are unreachable by the probe. For best + // auto-calibration results, all sides must be reachable. + #define CALIBRATION_MEASURE_RIGHT + #define CALIBRATION_MEASURE_FRONT + #define CALIBRATION_MEASURE_LEFT + #define CALIBRATION_MEASURE_BACK + + // Probing at the exact top center only works if the center is flat. If + // probing on a screwhead or hollow washer, probe near the edges. + //#define CALIBRATION_MEASURE_AT_TOP_EDGES + + // Define pin which is read during calibration + #ifndef CALIBRATION_PIN + #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop + #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin + //#define CALIBRATION_PIN_PULLDOWN + #define CALIBRATION_PIN_PULLUP + #endif +#endif + +/** + * Adaptive Step Smoothing increases the resolution of multi-axis moves, particularly at step frequencies + * below 1kHz (for AVR) or 10kHz (for ARM), where aliasing between axes in multi-axis moves causes audible + * vibration and surface artifacts. The algorithm adapts to provide the best possible step smoothing at the + * lowest stepping frequencies. + */ +//#define ADAPTIVE_STEP_SMOOTHING + +/** + * Custom Microstepping + * Override as-needed for your setup. Up to 3 MS pins are supported. + */ +//#define MICROSTEP1 LOW,LOW,LOW +//#define MICROSTEP2 HIGH,LOW,LOW +//#define MICROSTEP4 LOW,HIGH,LOW +//#define MICROSTEP8 HIGH,HIGH,LOW +//#define MICROSTEP16 LOW,LOW,HIGH +//#define MICROSTEP32 HIGH,LOW,HIGH + +// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU. +#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16] + +/** + * @section stepper motor current + * + * Some boards have a means of setting the stepper motor current via firmware. + * + * The power on motor currents are set by: + * PWM_MOTOR_CURRENT - used by MINIRAMBO & ULTIMAIN_2 + * known compatible chips: A4982 + * DIGIPOT_MOTOR_CURRENT - used by BQ_ZUM_MEGA_3D, RAMBO & SCOOVO_X9H + * known compatible chips: AD5206 + * DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2 + * known compatible chips: MCP4728 + * DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, AZTEEG_X5_MINI_WIFI, MIGHTYBOARD_REVE + * known compatible chips: MCP4451, MCP4018 + * + * Motor currents can also be set by M907 - M910 and by the LCD. + * M907 - applies to all. + * M908 - BQ_ZUM_MEGA_3D, RAMBO, PRINTRBOARD_REVF, RIGIDBOARD_V2 & SCOOVO_X9H + * M909, M910 & LCD - only PRINTRBOARD_REVF & RIGIDBOARD_V2 + */ +//#define PWM_MOTOR_CURRENT { 1300, 1300, 1250 } // Values in milliamps +//#define DIGIPOT_MOTOR_CURRENT { 135,135,135,135,135 } // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A) +//#define DAC_MOTOR_CURRENT_DEFAULT { 70, 80, 90, 80 } // Default drive percent - X, Y, Z, E axis + +// Use an I2C based DIGIPOT (e.g., Azteeg X3 Pro) +//#define DIGIPOT_I2C +#if ENABLED(DIGIPOT_I2C) && !defined(DIGIPOT_I2C_ADDRESS_A) + /** + * Common slave addresses: + * + * A (A shifted) B (B shifted) IC + * Smoothie 0x2C (0x58) 0x2D (0x5A) MCP4451 + * AZTEEG_X3_PRO 0x2C (0x58) 0x2E (0x5C) MCP4451 + * AZTEEG_X5_MINI 0x2C (0x58) 0x2E (0x5C) MCP4451 + * AZTEEG_X5_MINI_WIFI 0x58 0x5C MCP4451 + * MIGHTYBOARD_REVE 0x2F (0x5E) MCP4018 + */ + #define DIGIPOT_I2C_ADDRESS_A 0x2C // unshifted slave address for first DIGIPOT + #define DIGIPOT_I2C_ADDRESS_B 0x2D // unshifted slave address for second DIGIPOT +#endif + +//#define DIGIPOT_MCP4018 // Requires library from https://github.com/stawel/SlowSoftI2CMaster +#define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT: 4 AZTEEG_X3_PRO: 8 MKS SBASE: 5 +// Actual motor currents in Amps. The number of entries must match DIGIPOT_I2C_NUM_CHANNELS. +// These correspond to the physical drivers, so be mindful if the order is changed. +#define DIGIPOT_I2C_MOTOR_CURRENTS { 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0 } // AZTEEG_X3_PRO + +//=========================================================================== +//=============================Additional Features=========================== +//=========================================================================== + +// @section lcd + +#if EITHER(ULTIPANEL, EXTENSIBLE_UI) + #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) + #if ENABLED(ULTIPANEL) + #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" + #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen + #endif +#endif + +// Change values more rapidly when the encoder is rotated faster +#define ENCODER_RATE_MULTIPLIER +#if ENABLED(ENCODER_RATE_MULTIPLIER) + #define ENCODER_10X_STEPS_PER_SEC 30 // (steps/s) Encoder rate for 10x speed + #define ENCODER_100X_STEPS_PER_SEC 80 // (steps/s) Encoder rate for 100x speed +#endif + +// Play a beep when the feedrate is changed from the Status Screen +//#define BEEP_ON_FEEDRATE_CHANGE +#if ENABLED(BEEP_ON_FEEDRATE_CHANGE) + #define FEEDRATE_CHANGE_BEEP_DURATION 10 + #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 +#endif + +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + // BACK menu items keep the highlight at the top + //#define TURBO_BACK_MENU_ITEM + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU + +// Scroll a longer status message into view +//#define STATUS_MESSAGE_SCROLLING + +// On the Info Screen, display XY with one decimal place when possible +//#define LCD_DECIMAL_SMALL_XY + +// The timeout (in ms) to return to the status screen from sub-menus +//#define LCD_TIMEOUT_TO_STATUS 15000 + +// Add an 'M73' G-code to set the current percentage +//#define LCD_SET_PROGRESS_MANUALLY + +#if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS + //#define LCD_PROGRESS_BAR // Show a progress bar on HD44780 LCDs for SD printing + #if ENABLED(LCD_PROGRESS_BAR) + #define PROGRESS_BAR_BAR_TIME 2000 // (ms) Amount of time to show the bar + #define PROGRESS_BAR_MSG_TIME 3000 // (ms) Amount of time to show the status message + #define PROGRESS_MSG_EXPIRE 0 // (ms) Amount of time to retain the status message (0=forever) + //#define PROGRESS_MSG_ONCE // Show the message for MSG_TIME then clear it + //#define LCD_PROGRESS_BAR_TEST // Add a menu item to test the progress bar + #endif +#endif + +#if ENABLED(SDSUPPORT) + + // Some RAMPS and other boards don't detect when an SD card is inserted. You can work + // around this by connecting a push button or single throw switch to the pin defined + // as SD_DETECT_PIN in your board's pins definitions. + // This setting should be disabled unless you are using a push button, pulling the pin to ground. + // Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER). + #define SD_DETECT_INVERTED + + #define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished + #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place. + + // Reverse SD sort to show "more recent" files first, according to the card's FAT. + // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended. + #define SDCARD_RATHERRECENTFIRST + + #define SD_MENU_CONFIRM_START // Confirm the selected SD file before printing + + //#define MENU_ADDAUTOSTART // Add a menu option to run auto#.g files + + #define EVENT_GCODE_SD_STOP "G28XY" // G-code to run on Stop Print (e.g., "G28XY" or "G27") + + /** + * Continue after Power-Loss (Creality3D) + * + * Store the current state to the SD Card at the start of each layer + * during SD printing. If the recovery file is found at boot time, present + * an option on the LCD screen to continue the print from the last-known + * point in the file. + */ + //#define POWER_LOSS_RECOVERY + #if ENABLED(POWER_LOSS_RECOVERY) + //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate + //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume + //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. + + // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, + // especially with "vase mode" printing. Set too high and vases cannot be continued. + #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + #endif + + /** + * Sort SD file listings in alphabetical order. + * + * With this option enabled, items on SD cards will be sorted + * by name for easier navigation. + * + * By default... + * + * - Use the slowest -but safest- method for sorting. + * - Folders are sorted to the top. + * - The sort key is statically allocated. + * - No added G-code (M34) support. + * - 40 item sorting limit. (Items after the first 40 are unsorted.) + * + * SD sorting uses static allocation (as set by SDSORT_LIMIT), allowing the + * compiler to calculate the worst-case usage and throw an error if the SRAM + * limit is exceeded. + * + * - SDSORT_USES_RAM provides faster sorting via a static directory buffer. + * - SDSORT_USES_STACK does the same, but uses a local stack-based buffer. + * - SDSORT_CACHE_NAMES will retain the sorted file listing in RAM. (Expensive!) + * - SDSORT_DYNAMIC_RAM only uses RAM when the SD menu is visible. (Use with caution!) + */ + //#define SDCARD_SORT_ALPHA + + // SD Card Sorting options + #if ENABLED(SDCARD_SORT_ALPHA) + #define SDSORT_LIMIT 40 // Maximum number of sorted items (10-256). Costs 27 bytes each. + #define FOLDER_SORTING -1 // -1=above 0=none 1=below + #define SDSORT_GCODE false // Allow turning sorting on/off with LCD and M34 g-code. + #define SDSORT_USES_RAM false // Pre-allocate a static array for faster pre-sorting. + #define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.) + #define SDSORT_CACHE_NAMES false // Keep sorted items in RAM longer for speedy performance. Most expensive option. + #define SDSORT_DYNAMIC_RAM false // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use! + #define SDSORT_CACHE_VFATS 2 // Maximum number of 13-byte VFAT entries to use for sorting. + // Note: Only affects SCROLL_LONG_FILENAMES with SDSORT_CACHE_NAMES but not SDSORT_DYNAMIC_RAM. + #endif + + // This allows hosts to request long names for files and folders with M33 + //#define LONG_FILENAME_HOST_SUPPORT + + // Enable this option to scroll long filenames in the SD card menu + //#define SCROLL_LONG_FILENAMES + + // Leave the heaters on after Stop Print (not recommended!) + //#define SD_ABORT_NO_COOLDOWN + + /** + * This option allows you to abort SD printing when any endstop is triggered. + * This feature must be enabled with "M540 S1" or from the LCD menu. + * To have any effect, endstops must be enabled during SD printing. + */ + //#define SD_ABORT_ON_ENDSTOP_HIT + + /** + * This option makes it easier to print the same SD Card file again. + * On print completion the LCD Menu will open with the file selected. + * You can just click to start the print, or navigate elsewhere. + */ + //#define SD_REPRINT_LAST_SELECTED_FILE + + /** + * Auto-report SdCard status with M27 S + */ + //#define AUTO_REPORT_SD_STATUS + + /** + * Support for USB thumb drives using an Arduino USB Host Shield or + * equivalent MAX3421E breakout board. The USB thumb drive will appear + * to Marlin as an SD card. + * + * The MAX3421E can be assigned the same pins as the SD card reader, with + * the following pin mapping: + * + * SCLK, MOSI, MISO --> SCLK, MOSI, MISO + * INT --> SD_DETECT_PIN [1] + * SS --> SDSS + * + * [1] On AVR an interrupt-capable pin is best for UHS3 compatibility. + */ + //#define USB_FLASH_DRIVE_SUPPORT + #if ENABLED(USB_FLASH_DRIVE_SUPPORT) + #define USB_CS_PIN SDSS + #define USB_INTR_PIN SD_DETECT_PIN + + /** + * USB Host Shield Library + * + * - UHS2 uses no interrupts and has been production-tested + * on a LulzBot TAZ Pro with a 32-bit Archim board. + * + * - UHS3 is newer code with better USB compatibility. But it + * is less tested and is known to interfere with Servos. + * [1] This requires USB_INTR_PIN to be interrupt-capable. + */ + //#define USE_UHS3_USB + #endif + + /** + * When using a bootloader that supports SD-Firmware-Flashing, + * add a menu item to activate SD-FW-Update on the next reboot. + * + * Requires ATMEGA2560 (Arduino Mega) + * + * Tested with this bootloader: + * https://github.com/FleetProbe/MicroBridge-Arduino-ATMega2560 + */ + //#define SD_FIRMWARE_UPDATE + #if ENABLED(SD_FIRMWARE_UPDATE) + #define SD_FIRMWARE_UPDATE_EEPROM_ADDR 0x1FF + #define SD_FIRMWARE_UPDATE_ACTIVE_VALUE 0xF0 + #define SD_FIRMWARE_UPDATE_INACTIVE_VALUE 0xFF + #endif + + // Add an optimized binary file transfer mode, initiated with 'M28 B1' + //#define BINARY_FILE_TRANSFER + + #if HAS_SDCARD_CONNECTION + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD + #endif + +#endif // SDSUPPORT + +/** + * By default an onboard SD card reader may be shared as a USB mass- + * storage device. This option hides the SD card from the host PC. + */ +//#define NO_SD_HOST_DRIVE // Disable SD Card access over USB (for security). + +/** + * Additional options for Graphical Displays + * + * Use the optimizations here to improve printing performance, + * which can be adversely affected by graphical display drawing, + * especially when doing several short moves, and when printing + * on DELTA and SCARA machines. + * + * Some of these options may result in the display lagging behind + * controller events, as there is a trade-off between reliable + * printing performance versus fast display updates. + */ +#if HAS_GRAPHICAL_LCD + // Show SD percentage next to the progress bar + //#define DOGM_SD_PERCENT + + // Enable to save many cycles by drawing a hollow frame on the Info Screen + #define XYZ_HOLLOW_FRAME + + // Enable to save many cycles by drawing a hollow frame on Menu Screens + #define MENU_HOLLOW_FRAME + + // A bigger font is available for edit items. Costs 3120 bytes of PROGMEM. + // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese. + //#define USE_BIG_EDIT_FONT + + // A smaller font may be used on the Info Screen. Costs 2300 bytes of PROGMEM. + // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese. + //#define USE_SMALL_INFOFONT + + // Enable this option and reduce the value to optimize screen updates. + // The normal delay is 10µs. Use the lowest value that still gives a reliable display. + //#define DOGM_SPI_DELAY_US 5 + + // Swap the CW/CCW indicators in the graphics overlay + //#define OVERLAY_GFX_REVERSE + + /** + * ST7920-based LCDs can emulate a 16 x 4 character display using + * the ST7920 character-generator for very fast screen updates. + * Enable LIGHTWEIGHT_UI to use this special display mode. + * + * Since LIGHTWEIGHT_UI has limited space, the position and status + * message occupy the same line. Set STATUS_EXPIRE_SECONDS to the + * length of time to display the status message before clearing. + * + * Set STATUS_EXPIRE_SECONDS to zero to never clear the status. + * This will prevent position updates from being displayed. + */ + #if ENABLED(U8GLIB_ST7920) + //#define LIGHTWEIGHT_UI + #if ENABLED(LIGHTWEIGHT_UI) + #define STATUS_EXPIRE_SECONDS 20 + #endif + #endif + + /** + * Status (Info) Screen customizations + * These options may affect code size and screen render time. + * Custom status screens can forcibly override these settings. + */ + //#define STATUS_COMBINE_HEATERS // Use combined heater images instead of separate ones + //#define STATUS_HOTEND_NUMBERLESS // Use plain hotend icons instead of numbered ones (with 2+ hotends) + #define STATUS_HOTEND_INVERTED // Show solid nozzle bitmaps when heating (Requires STATUS_HOTEND_ANIM) + #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating + #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating + #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap + //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap + //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames + //#define STATUS_HEAT_PERCENT // Show heating in a progress bar + //#define BOOT_MARLIN_LOGO_SMALL // Show a smaller Marlin logo on the Boot Screen (saving 399 bytes of flash) + //#define BOOT_MARLIN_LOGO_ANIMATED // Animated Marlin logo. Costs ~‭3260 (or ~940) bytes of PROGMEM. + + // Frivolous Game Options + //#define MARLIN_BRICKOUT + //#define MARLIN_INVADERS + //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu + +#endif // HAS_GRAPHICAL_LCD + +// +// Lulzbot Touch UI +// +#if ENABLED(LULZBOT_TOUCH_UI) + // Display board used + //#define LCD_FTDI_VM800B35A // FTDI 3.5" with FT800 (320x240) + //#define LCD_4DSYSTEMS_4DLCD_FT843 // 4D Systems 4.3" (480x272) + //#define LCD_HAOYU_FT800CB // Haoyu with 4.3" or 5" (480x272) + //#define LCD_HAOYU_FT810CB // Haoyu with 5" (800x480) + //#define LCD_ALEPHOBJECTS_CLCD_UI // Aleph Objects Color LCD UI + + // Correct the resolution if not using the stock TFT panel. + //#define TOUCH_UI_320x240 + //#define TOUCH_UI_480x272 + //#define TOUCH_UI_800x480 + + // Mappings for boards with a standard RepRapDiscount Display connector + //#define AO_EXP1_PINMAP // AlephObjects CLCD UI EXP1 mapping + //#define AO_EXP2_PINMAP // AlephObjects CLCD UI EXP2 mapping + //#define CR10_TFT_PINMAP // Rudolph Riedel's CR10 pin mapping + //#define OTHER_PIN_LAYOUT // Define pins manually below + #if ENABLED(OTHER_PIN_LAYOUT) + // The pins for CS and MOD_RESET (PD) must be chosen. + #define CLCD_MOD_RESET 9 + #define CLCD_SPI_CS 10 + + // If using software SPI, specify pins for SCLK, MOSI, MISO + //#define CLCD_USE_SOFT_SPI + #if ENABLED(CLCD_USE_SOFT_SPI) + #define CLCD_SOFT_SPI_MOSI 11 + #define CLCD_SOFT_SPI_MISO 12 + #define CLCD_SOFT_SPI_SCLK 13 + #endif + #endif + + // Display Orientation. An inverted (i.e. upside-down) display + // is supported on the FT800. The FT810 and beyond also support + // portrait and mirrored orientations. + //#define TOUCH_UI_INVERTED + //#define TOUCH_UI_PORTRAIT + //#define TOUCH_UI_MIRRORED + + // UTF8 processing and rendering. + // Unsupported characters are shown as '?'. + //#define TOUCH_UI_USE_UTF8 + #if ENABLED(TOUCH_UI_USE_UTF8) + // Western accents support. These accented characters use + // combined bitmaps and require relatively little storage. + #define TOUCH_UI_UTF8_WESTERN_CHARSET + #if ENABLED(TOUCH_UI_UTF8_WESTERN_CHARSET) + // Additional character groups. These characters require + // full bitmaps and take up considerable storage: + //#define TOUCH_UI_UTF8_SUPERSCRIPTS // ¹ ² ³ + //#define TOUCH_UI_UTF8_COPYRIGHT // © ® + //#define TOUCH_UI_UTF8_GERMANIC // ß + //#define TOUCH_UI_UTF8_SCANDINAVIAN // Æ Ð Ø Þ æ ð ø þ + //#define TOUCH_UI_UTF8_PUNCTUATION // « » ¿ ¡ + //#define TOUCH_UI_UTF8_CURRENCY // ¢ £ ¤ ¥ + //#define TOUCH_UI_UTF8_ORDINALS // º ª + //#define TOUCH_UI_UTF8_MATHEMATICS // ± × ÷ + //#define TOUCH_UI_UTF8_FRACTIONS // ¼ ½ ¾ + //#define TOUCH_UI_UTF8_SYMBOLS // µ ¶ ¦ § ¬ + #endif + #endif + + // Use a smaller font when labels don't fit buttons + #define TOUCH_UI_FIT_TEXT + + // Allow language selection from menu at run-time (otherwise use LCD_LANGUAGE) + //#define LCD_LANGUAGE_1 en + //#define LCD_LANGUAGE_2 fr + //#define LCD_LANGUAGE_3 de + //#define LCD_LANGUAGE_4 es + //#define LCD_LANGUAGE_5 it + + // Use a numeric passcode for "Screen lock" keypad. + // (recommended for smaller displays) + //#define TOUCH_UI_PASSCODE + + // Output extra debug info for Touch UI events + //#define TOUCH_UI_DEBUG +#endif + +// +// FSMC Graphical TFT +// +#if ENABLED(FSMC_GRAPHICAL_TFT) + //#define TFT_MARLINUI_COLOR 0xFFFF // White + //#define TFT_MARLINBG_COLOR 0x0000 // Black + //#define TFT_DISABLED_COLOR 0x0003 // Almost black + //#define TFT_BTCANCEL_COLOR 0xF800 // Red + //#define TFT_BTARROWS_COLOR 0xDEE6 // 11011 110111 00110 Yellow + //#define TFT_BTOKMENU_COLOR 0x145F // 00010 100010 11111 Cyan +#endif + +// @section safety + +/** + * The watchdog hardware timer will do a reset and disable all outputs + * if the firmware gets too overloaded to read the temperature sensors. + * + * If you find that watchdog reboot causes your AVR board to hang forever, + * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO. + * NOTE: This method is less reliable as it can only catch hangups while + * interrupts are enabled. + */ +#define USE_WATCHDOG +#if ENABLED(USE_WATCHDOG) + //#define WATCHDOG_RESET_MANUAL +#endif + +// @section lcd + +/** + * Babystepping enables movement of the axes by tiny increments without changing + * the current position values. This feature is used primarily to adjust the Z + * axis in the first layer of a print in real-time. + * + * Warning: Does not respect endstops! + */ +//#define BABYSTEPPING +#if ENABLED(BABYSTEPPING) + //#define BABYSTEP_WITHOUT_HOMING + //#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA! + #define BABYSTEP_INVERT_Z false // Change if Z babysteps should go the other way + #define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion. + + //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping. + #if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING) + #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds. + // Note: Extra time may be added to mitigate controller latency. + //#define BABYSTEP_ALWAYS_AVAILABLE // Allow babystepping at all times (not just during movement). + //#define MOVE_Z_WHEN_IDLE // Jump to the move Z menu on doubleclick when printer is idle. + #if ENABLED(MOVE_Z_WHEN_IDLE) + #define MOVE_Z_IDLE_MULTIPLICATOR 1 // Multiply 1mm by this factor for the move step size. + #endif + #endif + + //#define BABYSTEP_DISPLAY_TOTAL // Display total babysteps since last G28 + + //#define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping + #if ENABLED(BABYSTEP_ZPROBE_OFFSET) + //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets + //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor + #endif +#endif + +// @section extruder + +/** + * Linear Pressure Control v1.5 + * + * Assumption: advance [steps] = k * (delta velocity [steps/s]) + * K=0 means advance disabled. + * + * NOTE: K values for LIN_ADVANCE 1.5 differ from earlier versions! + * + * Set K around 0.22 for 3mm PLA Direct Drive with ~6.5cm between the drive gear and heatbreak. + * Larger K values will be needed for flexible filament and greater distances. + * If this algorithm produces a higher speed offset than the extruder can handle (compared to E jerk) + * print acceleration will be reduced during the affected moves to keep within the limit. + * + * See http://marlinfw.org/docs/features/lin_advance.html for full instructions. + * Mention @Sebastianv650 on GitHub to alert the author of any issues. + */ +//#define LIN_ADVANCE +#if ENABLED(LIN_ADVANCE) + //#define EXTRA_LIN_ADVANCE_K // Enable for second linear advance constants + #define LIN_ADVANCE_K 0.22 // Unit: mm compression per 1mm/s extruder speed + //#define LA_DEBUG // If enabled, this will generate debug information output over USB. +#endif + +// @section leveling + +/** + * Points to probe for all 3-point Leveling procedures. + * Override if the automatically selected points are inadequate. + */ +#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL) + //#define PROBE_PT_1_X 15 + //#define PROBE_PT_1_Y 180 + //#define PROBE_PT_2_X 15 + //#define PROBE_PT_2_Y 20 + //#define PROBE_PT_3_X 170 + //#define PROBE_PT_3_Y 20 +#endif + +/** + * Override MIN_PROBE_EDGE for each side of the build plate + * Useful to get probe points to exact positions on targets or + * to allow leveling to avoid plate clamps on only specific + * sides of the bed. + * + * If you are replacing the prior *_PROBE_BED_POSITION options, + * LEFT and FRONT values in most cases will map directly over + * RIGHT and REAR would be the inverse such as + * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION) + * + * This will allow all positions to match at compilation, however + * should the probe position be modified with M851XY then the + * probe points will follow. This prevents any change from causing + * the probe to be unable to reach any points. + */ +#if PROBE_SELECTED && !IS_KINEMATIC + //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE + //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE + //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE + //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE +#endif + +#if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL) + // Override the mesh area if the automatic (max) area is too large + //#define MESH_MIN_X MESH_INSET + //#define MESH_MIN_Y MESH_INSET + //#define MESH_MAX_X X_BED_SIZE - (MESH_INSET) + //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET) +#endif + +/** + * Repeatedly attempt G29 leveling until it succeeds. + * Stop after G29_MAX_RETRIES attempts. + */ +//#define G29_RETRY_AND_RECOVER +#if ENABLED(G29_RETRY_AND_RECOVER) + #define G29_MAX_RETRIES 3 + #define G29_HALT_ON_FAILURE + /** + * Specify the GCODE commands that will be executed when leveling succeeds, + * between attempts, and after the maximum number of retries have been tried. + */ + #define G29_SUCCESS_COMMANDS "M117 Bed leveling done." + #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0" + #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1" + +#endif + +// @section extras + +// +// G2/G3 Arc Support +// +#define ARC_SUPPORT // Disable this feature to save ~3226 bytes +#if ENABLED(ARC_SUPPORT) + #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles + //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes +#endif + +// Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes. +//#define BEZIER_CURVE_SUPPORT + +/** + * G38 Probe Target + * + * This option adds G38.2 and G38.3 (probe towards target) + * and optionally G38.4 and G38.5 (probe away from target). + * Set MULTIPLE_PROBING for G38 to probe more than once. + */ +//#define G38_PROBE_TARGET +#if ENABLED(G38_PROBE_TARGET) + //#define G38_PROBE_AWAY // Include G38.4 and G38.5 to probe away from target + #define G38_MINIMUM_MOVE 0.0275 // (mm) Minimum distance that will produce a move. +#endif + +// Moves (or segments) with fewer steps than this will be joined with the next move +#define MIN_STEPS_PER_SEGMENT 6 + +/** + * Minimum delay before and after setting the stepper DIR (in ns) + * 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire) + * 20 : Minimum for TMC2xxx drivers + * 200 : Minimum for A4988 drivers + * 400 : Minimum for A5984 drivers + * 500 : Minimum for LV8729 drivers (guess, no info in datasheet) + * 650 : Minimum for DRV8825 drivers + * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet) + * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet) + * + * Override the default value based on the driver type set in Configuration.h. + */ +//#define MINIMUM_STEPPER_POST_DIR_DELAY 650 +//#define MINIMUM_STEPPER_PRE_DIR_DELAY 650 + +/** + * Minimum stepper driver pulse width (in µs) + * 0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers + * 0 : Minimum 500ns for LV8729, adjusted in stepper.h + * 1 : Minimum for A4988 and A5984 stepper drivers + * 2 : Minimum for DRV8825 stepper drivers + * 3 : Minimum for TB6600 stepper drivers + * 30 : Minimum for TB6560 stepper drivers + * + * Override the default value based on the driver type set in Configuration.h. + */ +//#define MINIMUM_STEPPER_PULSE 2 + +/** + * Maximum stepping rate (in Hz) the stepper driver allows + * If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE) + * 500000 : Maximum for A4988 stepper driver + * 400000 : Maximum for TMC2xxx stepper drivers + * 250000 : Maximum for DRV8825 stepper driver + * 200000 : Maximum for LV8729 stepper driver + * 150000 : Maximum for TB6600 stepper driver + * 15000 : Maximum for TB6560 stepper driver + * + * Override the default value based on the driver type set in Configuration.h. + */ +//#define MAXIMUM_STEPPER_RATE 250000 + +// @section temperature + +// Control heater 0 and heater 1 in parallel. +//#define HEATERS_PARALLEL + +//=========================================================================== +//================================= Buffers ================================= +//=========================================================================== + +// @section hidden + +// The number of linear motions that can be in the plan at any give time. +// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2 (e.g. 8, 16, 32) because shifts and ors are used to do the ring-buffering. +#if ENABLED(SDSUPPORT) + #define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller +#else + #define BLOCK_BUFFER_SIZE 16 // maximize block buffer +#endif + +// @section serial + +// The ASCII buffer for serial input +#define MAX_CMD_SIZE 96 +#define BUFSIZE 4 + +// Transmission to Host Buffer Size +// To save 386 bytes of PROGMEM (and TX_BUFFER_SIZE+3 bytes of RAM) set to 0. +// To buffer a simple "ok" you need 4 bytes. +// For ADVANCED_OK (M105) you need 32 bytes. +// For debug-echo: 128 bytes for the optimal speed. +// Other output doesn't need to be that speedy. +// :[0, 2, 4, 8, 16, 32, 64, 128, 256] +#define TX_BUFFER_SIZE 0 + +// Host Receive Buffer Size +// Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough. +// To use flow control, set this buffer size to at least 1024 bytes. +// :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048] +//#define RX_BUFFER_SIZE 1024 + +#if RX_BUFFER_SIZE >= 1024 + // Enable to have the controller send XON/XOFF control characters to + // the host to signal the RX buffer is becoming full. + //#define SERIAL_XON_XOFF +#endif + +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + +#if ENABLED(SDSUPPORT) + // Enable this option to collect and display the maximum + // RX queue usage after transferring a file to SD. + //#define SERIAL_STATS_MAX_RX_QUEUED + + // Enable this option to collect and display the number + // of dropped bytes after a file transfer to SD. + //#define SERIAL_STATS_DROPPED_RX +#endif + +// Enable an emergency-command parser to intercept certain commands as they +// enter the serial receive buffer, so they cannot be blocked. +// Currently handles M108, M112, M410 +// Does not work on boards using AT90USB (USBCON) processors! +//#define EMERGENCY_PARSER + +// Bad Serial-connections can miss a received command by sending an 'ok' +// Therefore some clients abort after 30 seconds in a timeout. +// Some other clients start sending commands while receiving a 'wait'. +// This "wait" is only sent when the buffer is empty. 1 second is a good value here. +//#define NO_TIMEOUTS 1000 // Milliseconds + +// Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary. +//#define ADVANCED_OK + +// Printrun may have trouble receiving long strings all at once. +// This option inserts short delays between lines of serial output. +#define SERIAL_OVERRUN_PROTECTION + +// @section extras + +/** + * Extra Fan Speed + * Adds a secondary fan speed for each print-cooling fan. + * 'M106 P T3-255' : Set a secondary speed for + * 'M106 P T2' : Use the set secondary speed + * 'M106 P T1' : Restore the previous fan speed + */ +//#define EXTRA_FAN_SPEED + +/** + * Firmware-based and LCD-controlled retract + * + * Add G10 / G11 commands for automatic firmware-based retract / recover. + * Use M207 and M208 to define parameters for retract / recover. + * + * Use M209 to enable or disable auto-retract. + * With auto-retract enabled, all G1 E moves within the set range + * will be converted to firmware-based retract/recover moves. + * + * Be sure to turn off auto-retract during filament change. + * + * Note that M207 / M208 / M209 settings are saved to EEPROM. + * + */ +//#define FWRETRACT +#if ENABLED(FWRETRACT) + #define FWRETRACT_AUTORETRACT // Override slicer retractions + #if ENABLED(FWRETRACT_AUTORETRACT) + #define MIN_AUTORETRACT 0.1 // (mm) Don't convert E moves under this length + #define MAX_AUTORETRACT 10.0 // (mm) Don't convert E moves over this length + #endif + #define RETRACT_LENGTH 3 // (mm) Default retract length (positive value) + #define RETRACT_LENGTH_SWAP 13 // (mm) Default swap retract length (positive value) + #define RETRACT_FEEDRATE 45 // (mm/s) Default feedrate for retracting + #define RETRACT_ZRAISE 0 // (mm) Default retract Z-raise + #define RETRACT_RECOVER_LENGTH 0 // (mm) Default additional recover length (added to retract length on recover) + #define RETRACT_RECOVER_LENGTH_SWAP 0 // (mm) Default additional swap recover length (added to retract length on recover from toolchange) + #define RETRACT_RECOVER_FEEDRATE 8 // (mm/s) Default feedrate for recovering from retraction + #define RETRACT_RECOVER_FEEDRATE_SWAP 8 // (mm/s) Default feedrate for recovering from swap retraction + #if ENABLED(MIXING_EXTRUDER) + //#define RETRACT_SYNC_MIXING // Retract and restore all mixing steppers simultaneously + #endif +#endif + +/** + * Universal tool change settings. + * Applies to all types of extruders except where explicitly noted. + */ +#if EXTRUDERS > 1 + // Z raise distance for tool-change, as needed for some extruders + #define TOOLCHANGE_ZRAISE 2 // (mm) + //#define TOOLCHANGE_NO_RETURN // Never return to the previous position on tool-change + + // Retract and prime filament on tool-change + //#define TOOLCHANGE_FILAMENT_SWAP + #if ENABLED(TOOLCHANGE_FILAMENT_SWAP) + #define TOOLCHANGE_FIL_SWAP_LENGTH 12 // (mm) + #define TOOLCHANGE_FIL_EXTRA_PRIME 2 // (mm) + #define TOOLCHANGE_FIL_SWAP_RETRACT_SPEED 3600 // (mm/m) + #define TOOLCHANGE_FIL_SWAP_PRIME_SPEED 3600 // (mm/m) + #endif + + /** + * Position to park head during tool change. + * Doesn't apply to SWITCHING_TOOLHEAD, DUAL_X_CARRIAGE, or PARKING_EXTRUDER + */ + //#define TOOLCHANGE_PARK + #if ENABLED(TOOLCHANGE_PARK) + #define TOOLCHANGE_PARK_XY { X_MIN_POS + 10, Y_MIN_POS + 10 } + #define TOOLCHANGE_PARK_XY_FEEDRATE 6000 // (mm/m) + #endif +#endif + +/** + * Advanced Pause + * Experimental feature for filament change support and for parking the nozzle when paused. + * Adds the GCode M600 for initiating filament change. + * If PARK_HEAD_ON_PAUSE enabled, adds the GCode M125 to pause printing and park the nozzle. + * + * Requires an LCD display. + * Requires NOZZLE_PARK_FEATURE. + * This feature is required for the default FILAMENT_RUNOUT_SCRIPT. + */ +//#define ADVANCED_PAUSE_FEATURE +#if ENABLED(ADVANCED_PAUSE_FEATURE) + #define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate. + #define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract. + // This short retract is done immediately, before parking the nozzle. + #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast. + #define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate. + #define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload. + // For Bowden, the full length of the tube and nozzle. + // For direct drive, the full length of the nozzle. + // Set to 0 for manual unloading. + #define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load. + #define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material. + // 0 to disable start loading and skip to fast load only + #define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast. + #define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate. + #define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle. + // For Bowden, the full length of the tube and nozzle. + // For direct drive, the full length of the nozzle. + //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted. + #define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate. + #define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading. + // Set to 0 for manual extrusion. + // Filament can be extruded repeatedly from the Filament Change menu + // until extrusion is consistent, and to purge old filament. + #define ADVANCED_PAUSE_RESUME_PRIME 0 // (mm) Extra distance to prime nozzle after returning from park. + //#define ADVANCED_PAUSE_FANS_PAUSE // Turn off print-cooling fans while the machine is paused. + + // Filament Unload does a Retract, Delay, and Purge first: + #define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length. + #define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract. + #define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged. + + #define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety. + #define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed. + #define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change. + + //#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change. + //#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change + + //#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu. + //#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302) +#endif + +// @section tmc + +/** + * TMC26X Stepper Driver options + * + * The TMC26XStepper library is required for this stepper driver. + * https://github.com/trinamic/TMC26XStepper + */ +#if HAS_DRIVER(TMC26X) + + #if AXIS_DRIVER_TYPE_X(TMC26X) + #define X_MAX_CURRENT 1000 // (mA) + #define X_SENSE_RESISTOR 91 // (mOhms) + #define X_MICROSTEPS 16 // Number of microsteps + #endif + + #if AXIS_DRIVER_TYPE_X2(TMC26X) + #define X2_MAX_CURRENT 1000 + #define X2_SENSE_RESISTOR 91 + #define X2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Y(TMC26X) + #define Y_MAX_CURRENT 1000 + #define Y_SENSE_RESISTOR 91 + #define Y_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Y2(TMC26X) + #define Y2_MAX_CURRENT 1000 + #define Y2_SENSE_RESISTOR 91 + #define Y2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Z(TMC26X) + #define Z_MAX_CURRENT 1000 + #define Z_SENSE_RESISTOR 91 + #define Z_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Z2(TMC26X) + #define Z2_MAX_CURRENT 1000 + #define Z2_SENSE_RESISTOR 91 + #define Z2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Z3(TMC26X) + #define Z3_MAX_CURRENT 1000 + #define Z3_SENSE_RESISTOR 91 + #define Z3_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E0(TMC26X) + #define E0_MAX_CURRENT 1000 + #define E0_SENSE_RESISTOR 91 + #define E0_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E1(TMC26X) + #define E1_MAX_CURRENT 1000 + #define E1_SENSE_RESISTOR 91 + #define E1_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E2(TMC26X) + #define E2_MAX_CURRENT 1000 + #define E2_SENSE_RESISTOR 91 + #define E2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E3(TMC26X) + #define E3_MAX_CURRENT 1000 + #define E3_SENSE_RESISTOR 91 + #define E3_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E4(TMC26X) + #define E4_MAX_CURRENT 1000 + #define E4_SENSE_RESISTOR 91 + #define E4_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E5(TMC26X) + #define E5_MAX_CURRENT 1000 + #define E5_SENSE_RESISTOR 91 + #define E5_MICROSTEPS 16 + #endif + +#endif // TMC26X + +// @section tmc_smart + +/** + * To use TMC2130, TMC2160, TMC2660, TMC5130, TMC5160 stepper drivers in SPI mode + * connect your SPI pins to the hardware SPI interface on your board and define + * the required CS pins in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 + * pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.). + * You may also use software SPI if you wish to use general purpose IO pins. + * + * To use TMC2208 stepper UART-configurable stepper drivers connect #_SERIAL_TX_PIN + * to the driver side PDN_UART pin with a 1K resistor. + * To use the reading capabilities, also connect #_SERIAL_RX_PIN to PDN_UART without + * a resistor. + * The drivers can also be used with hardware serial. + * + * TMCStepper library is required to use TMC stepper drivers. + * https://github.com/teemuatlut/TMCStepper + */ +#if HAS_TRINAMIC + + #define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current + #define INTERPOLATE true // Interpolate X/Y/Z_MICROSTEPS to 256 + + #if AXIS_IS_TMC(X) + #define X_CURRENT 800 // (mA) RMS current. Multiply by 1.414 for peak current. + #define X_MICROSTEPS 16 // 0..256 + #define X_RSENSE 0.11 + #define X_CHAIN_POS -1 // <=0 : Not chained. 1 : MCU MOSI connected. 2 : Next in chain, ... + #endif + + #if AXIS_IS_TMC(X2) + #define X2_CURRENT 800 + #define X2_MICROSTEPS 16 + #define X2_RSENSE 0.11 + #define X2_CHAIN_POS -1 + #endif + + #if AXIS_IS_TMC(Y) + #define Y_CURRENT 800 + #define Y_MICROSTEPS 16 + #define Y_RSENSE 0.11 + #define Y_CHAIN_POS -1 + #endif + + #if AXIS_IS_TMC(Y2) + #define Y2_CURRENT 800 + #define Y2_MICROSTEPS 16 + #define Y2_RSENSE 0.11 + #define Y2_CHAIN_POS -1 + #endif + + #if AXIS_IS_TMC(Z) + #define Z_CURRENT 800 + #define Z_MICROSTEPS 16 + #define Z_RSENSE 0.11 + #define Z_CHAIN_POS -1 + #endif + + #if AXIS_IS_TMC(Z2) + #define Z2_CURRENT 800 + #define Z2_MICROSTEPS 16 + #define Z2_RSENSE 0.11 + #define Z2_CHAIN_POS -1 + #endif + + #if AXIS_IS_TMC(Z3) + #define Z3_CURRENT 800 + #define Z3_MICROSTEPS 16 + #define Z3_RSENSE 0.11 + #define Z3_CHAIN_POS -1 + #endif + + #if AXIS_IS_TMC(E0) + #define E0_CURRENT 800 + #define E0_MICROSTEPS 16 + #define E0_RSENSE 0.11 + #define E0_CHAIN_POS -1 + #endif + + #if AXIS_IS_TMC(E1) + #define E1_CURRENT 800 + #define E1_MICROSTEPS 16 + #define E1_RSENSE 0.11 + #define E1_CHAIN_POS -1 + #endif + + #if AXIS_IS_TMC(E2) + #define E2_CURRENT 800 + #define E2_MICROSTEPS 16 + #define E2_RSENSE 0.11 + #define E2_CHAIN_POS -1 + #endif + + #if AXIS_IS_TMC(E3) + #define E3_CURRENT 800 + #define E3_MICROSTEPS 16 + #define E3_RSENSE 0.11 + #define E3_CHAIN_POS -1 + #endif + + #if AXIS_IS_TMC(E4) + #define E4_CURRENT 800 + #define E4_MICROSTEPS 16 + #define E4_RSENSE 0.11 + #define E4_CHAIN_POS -1 + #endif + + #if AXIS_IS_TMC(E5) + #define E5_CURRENT 800 + #define E5_MICROSTEPS 16 + #define E5_RSENSE 0.11 + #define E5_CHAIN_POS -1 + #endif + + /** + * Override default SPI pins for TMC2130, TMC2160, TMC2660, TMC5130 and TMC5160 drivers here. + * The default pins can be found in your board's pins file. + */ + //#define X_CS_PIN -1 + //#define Y_CS_PIN -1 + //#define Z_CS_PIN -1 + //#define X2_CS_PIN -1 + //#define Y2_CS_PIN -1 + //#define Z2_CS_PIN -1 + //#define Z3_CS_PIN -1 + //#define E0_CS_PIN -1 + //#define E1_CS_PIN -1 + //#define E2_CS_PIN -1 + //#define E3_CS_PIN -1 + //#define E4_CS_PIN -1 + //#define E5_CS_PIN -1 + + /** + * Software option for SPI driven drivers (TMC2130, TMC2160, TMC2660, TMC5130 and TMC5160). + * The default SW SPI pins are defined the respective pins files, + * but you can override or define them here. + */ + //#define TMC_USE_SW_SPI + //#define TMC_SW_MOSI -1 + //#define TMC_SW_MISO -1 + //#define TMC_SW_SCK -1 + + /** + * Four TMC2209 drivers can use the same HW/SW serial port with hardware configured addresses. + * Set the address using jumpers on pins MS1 and MS2. + * Address | MS1 | MS2 + * 0 | LOW | LOW + * 1 | HIGH | LOW + * 2 | LOW | HIGH + * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. + */ + #define X_SLAVE_ADDRESS 0 + #define Y_SLAVE_ADDRESS 0 + #define Z_SLAVE_ADDRESS 0 + #define X2_SLAVE_ADDRESS 0 + #define Y2_SLAVE_ADDRESS 0 + #define Z2_SLAVE_ADDRESS 0 + #define Z3_SLAVE_ADDRESS 0 + #define E0_SLAVE_ADDRESS 0 + #define E1_SLAVE_ADDRESS 0 + #define E2_SLAVE_ADDRESS 0 + #define E3_SLAVE_ADDRESS 0 + #define E4_SLAVE_ADDRESS 0 + #define E5_SLAVE_ADDRESS 0 + + /** + * Software enable + * + * Use for drivers that do not use a dedicated enable pin, but rather handle the same + * function through a communication line such as SPI or UART. + */ + //#define SOFTWARE_DRIVER_ENABLE + + /** + * TMC2130, TMC2160, TMC2208, TMC2209, TMC5130 and TMC5160 only + * Use Trinamic's ultra quiet stepping mode. + * When disabled, Marlin will use spreadCycle stepping mode. + */ + #define STEALTHCHOP_XY + #define STEALTHCHOP_Z + #define STEALTHCHOP_E + + /** + * Optimize spreadCycle chopper parameters by using predefined parameter sets + * or with the help of an example included in the library. + * Provided parameter sets are + * CHOPPER_DEFAULT_12V + * CHOPPER_DEFAULT_19V + * CHOPPER_DEFAULT_24V + * CHOPPER_DEFAULT_36V + * CHOPPER_PRUSAMK3_24V // Imported parameters from the official Prusa firmware for MK3 (24V) + * CHOPPER_MARLIN_119 // Old defaults from Marlin v1.1.9 + * + * Define you own with + * { , , hysteresis_start[1..8] } + */ + #define CHOPPER_TIMING CHOPPER_DEFAULT_12V + + /** + * Monitor Trinamic drivers for error conditions, + * like overtemperature and short to ground. + * In the case of overtemperature Marlin can decrease the driver current until error condition clears. + * Other detected conditions can be used to stop the current print. + * Relevant g-codes: + * M906 - Set or get motor current in milliamps using axis codes X, Y, Z, E. Report values if no axis codes given. + * M911 - Report stepper driver overtemperature pre-warn condition. + * M912 - Clear stepper driver overtemperature pre-warn condition flag. + * M122 - Report driver parameters (Requires TMC_DEBUG) + */ + //#define MONITOR_DRIVER_STATUS + + #if ENABLED(MONITOR_DRIVER_STATUS) + #define CURRENT_STEP_DOWN 50 // [mA] + #define REPORT_CURRENT_CHANGE + #define STOP_ON_ERROR + #endif + + /** + * TMC2130, TMC2160, TMC2208, TMC2209, TMC5130 and TMC5160 only + * The driver will switch to spreadCycle when stepper speed is over HYBRID_THRESHOLD. + * This mode allows for faster movements at the expense of higher noise levels. + * STEALTHCHOP_(XY|Z|E) must be enabled to use HYBRID_THRESHOLD. + * M913 X/Y/Z/E to live tune the setting + */ + //#define HYBRID_THRESHOLD + + #define X_HYBRID_THRESHOLD 100 // [mm/s] + #define X2_HYBRID_THRESHOLD 100 + #define Y_HYBRID_THRESHOLD 100 + #define Y2_HYBRID_THRESHOLD 100 + #define Z_HYBRID_THRESHOLD 3 + #define Z2_HYBRID_THRESHOLD 3 + #define Z3_HYBRID_THRESHOLD 3 + #define E0_HYBRID_THRESHOLD 30 + #define E1_HYBRID_THRESHOLD 30 + #define E2_HYBRID_THRESHOLD 30 + #define E3_HYBRID_THRESHOLD 30 + #define E4_HYBRID_THRESHOLD 30 + #define E5_HYBRID_THRESHOLD 30 + + /** + * Use StallGuard2 to home / probe X, Y, Z. + * + * TMC2130, TMC2160, TMC2209, TMC2660, TMC5130, and TMC5160 only + * Connect the stepper driver's DIAG1 pin to the X/Y endstop pin. + * X, Y, and Z homing will always be done in spreadCycle mode. + * + * X/Y/Z_STALL_SENSITIVITY is the default stall threshold. + * Use M914 X Y Z to set the stall threshold at runtime: + * + * Sensitivity TMC2209 Others + * HIGHEST 255 -64 (Too sensitive => False positive) + * LOWEST 0 63 (Too insensitive => No trigger) + * + * It is recommended to set [XYZ]_HOME_BUMP_MM to 0. + * + * SPI_ENDSTOPS *** Beta feature! *** TMC2130 Only *** + * Poll the driver through SPI to determine load when homing. + * Removes the need for a wire from DIAG1 to an endstop pin. + * + * IMPROVE_HOMING_RELIABILITY tunes acceleration and jerk when + * homing and adds a guard period for endstop triggering. + */ + //#define SENSORLESS_HOMING // StallGuard capable drivers only + + /** + * Use StallGuard2 to probe the bed with the nozzle. + * + * CAUTION: This could cause damage to machines that use a lead screw or threaded rod + * to move the Z axis. Take extreme care when attempting to enable this feature. + */ + //#define SENSORLESS_PROBING // StallGuard capable drivers only + + #if EITHER(SENSORLESS_HOMING, SENSORLESS_PROBING) + // TMC2209: 0...255. TMC2130: -64...63 + #define X_STALL_SENSITIVITY 8 + #define X2_STALL_SENSITIVITY X_STALL_SENSITIVITY + #define Y_STALL_SENSITIVITY 8 + //#define Z_STALL_SENSITIVITY 8 + //#define SPI_ENDSTOPS // TMC2130 only + //#define IMPROVE_HOMING_RELIABILITY + #endif + + /** + * Beta feature! + * Create a 50/50 square wave step pulse optimal for stepper drivers. + */ + //#define SQUARE_WAVE_STEPPING + + /** + * Enable M122 debugging command for TMC stepper drivers. + * M122 S0/1 will enable continous reporting. + */ + //#define TMC_DEBUG + + /** + * You can set your own advanced settings by filling in predefined functions. + * A list of available functions can be found on the library github page + * https://github.com/teemuatlut/TMCStepper + * + * Example: + * #define TMC_ADV() { \ + * stepperX.diag0_temp_prewarn(1); \ + * stepperY.interpolate(0); \ + * } + */ + #define TMC_ADV() { } + +#endif // HAS_TRINAMIC + +// @section L6470 + +/** + * L6470 Stepper Driver options + * + * Arduino-L6470 library (0.7.0 or higher) is required for this stepper driver. + * https://github.com/ameyer/Arduino-L6470 + * + * Requires the following to be defined in your pins_YOUR_BOARD file + * L6470_CHAIN_SCK_PIN + * L6470_CHAIN_MISO_PIN + * L6470_CHAIN_MOSI_PIN + * L6470_CHAIN_SS_PIN + * L6470_RESET_CHAIN_PIN (optional) + */ +#if HAS_DRIVER(L6470) + + //#define L6470_CHITCHAT // Display additional status info + + #if AXIS_DRIVER_TYPE_X(L6470) + #define X_MICROSTEPS 128 // Number of microsteps (VALID: 1, 2, 4, 8, 16, 32, 128) + #define X_OVERCURRENT 2000 // (mA) Current where the driver detects an over current (VALID: 375 x (1 - 16) - 6A max - rounds down) + #define X_STALLCURRENT 1500 // (mA) Current where the driver detects a stall (VALID: 31.25 * (1-128) - 4A max - rounds down) + #define X_MAX_VOLTAGE 127 // 0-255, Maximum effective voltage seen by stepper + #define X_CHAIN_POS -1 // Position in SPI chain. (<=0 : Not in chain. 1 : Nearest MOSI) + #endif + + #if AXIS_DRIVER_TYPE_X2(L6470) + #define X2_MICROSTEPS 128 + #define X2_OVERCURRENT 2000 + #define X2_STALLCURRENT 1500 + #define X2_MAX_VOLTAGE 127 + #define X2_CHAIN_POS -1 + #endif + + #if AXIS_DRIVER_TYPE_Y(L6470) + #define Y_MICROSTEPS 128 + #define Y_OVERCURRENT 2000 + #define Y_STALLCURRENT 1500 + #define Y_MAX_VOLTAGE 127 + #define Y_CHAIN_POS -1 + #endif + + #if AXIS_DRIVER_TYPE_Y2(L6470) + #define Y2_MICROSTEPS 128 + #define Y2_OVERCURRENT 2000 + #define Y2_STALLCURRENT 1500 + #define Y2_MAX_VOLTAGE 127 + #define Y2_CHAIN_POS -1 + #endif + + #if AXIS_DRIVER_TYPE_Z(L6470) + #define Z_MICROSTEPS 128 + #define Z_OVERCURRENT 2000 + #define Z_STALLCURRENT 1500 + #define Z_MAX_VOLTAGE 127 + #define Z_CHAIN_POS -1 + #endif + + #if AXIS_DRIVER_TYPE_Z2(L6470) + #define Z2_MICROSTEPS 128 + #define Z2_OVERCURRENT 2000 + #define Z2_STALLCURRENT 1500 + #define Z2_MAX_VOLTAGE 127 + #define Z2_CHAIN_POS -1 + #endif + + #if AXIS_DRIVER_TYPE_Z3(L6470) + #define Z3_MICROSTEPS 128 + #define Z3_OVERCURRENT 2000 + #define Z3_STALLCURRENT 1500 + #define Z3_MAX_VOLTAGE 127 + #define Z3_CHAIN_POS -1 + #endif + + #if AXIS_DRIVER_TYPE_E0(L6470) + #define E0_MICROSTEPS 128 + #define E0_OVERCURRENT 2000 + #define E0_STALLCURRENT 1500 + #define E0_MAX_VOLTAGE 127 + #define E0_CHAIN_POS -1 + #endif + + #if AXIS_DRIVER_TYPE_E1(L6470) + #define E1_MICROSTEPS 128 + #define E1_OVERCURRENT 2000 + #define E1_STALLCURRENT 1500 + #define E1_MAX_VOLTAGE 127 + #define E1_CHAIN_POS -1 + #endif + + #if AXIS_DRIVER_TYPE_E2(L6470) + #define E2_MICROSTEPS 128 + #define E2_OVERCURRENT 2000 + #define E2_STALLCURRENT 1500 + #define E2_MAX_VOLTAGE 127 + #define E2_CHAIN_POS -1 + #endif + + #if AXIS_DRIVER_TYPE_E3(L6470) + #define E3_MICROSTEPS 128 + #define E3_OVERCURRENT 2000 + #define E3_STALLCURRENT 1500 + #define E3_MAX_VOLTAGE 127 + #define E3_CHAIN_POS -1 + #endif + + #if AXIS_DRIVER_TYPE_E4(L6470) + #define E4_MICROSTEPS 128 + #define E4_OVERCURRENT 2000 + #define E4_STALLCURRENT 1500 + #define E4_MAX_VOLTAGE 127 + #define E4_CHAIN_POS -1 + #endif + + #if AXIS_DRIVER_TYPE_E5(L6470) + #define E5_MICROSTEPS 128 + #define E5_OVERCURRENT 2000 + #define E5_STALLCURRENT 1500 + #define E5_MAX_VOLTAGE 127 + #define E5_CHAIN_POS -1 + #endif + + /** + * Monitor L6470 drivers for error conditions like over temperature and over current. + * In the case of over temperature Marlin can decrease the drive until the error condition clears. + * Other detected conditions can be used to stop the current print. + * Relevant g-codes: + * M906 - I1/2/3/4/5 Set or get motor drive level using axis codes X, Y, Z, E. Report values if no axis codes given. + * I not present or I0 or I1 - X, Y, Z or E0 + * I2 - X2, Y2, Z2 or E1 + * I3 - Z3 or E3 + * I4 - E4 + * I5 - E5 + * M916 - Increase drive level until get thermal warning + * M917 - Find minimum current thresholds + * M918 - Increase speed until max or error + * M122 S0/1 - Report driver parameters + */ + //#define MONITOR_L6470_DRIVER_STATUS + + #if ENABLED(MONITOR_L6470_DRIVER_STATUS) + #define KVAL_HOLD_STEP_DOWN 1 + //#define L6470_STOP_ON_ERROR + #endif + +#endif // L6470 + +/** + * TWI/I2C BUS + * + * This feature is an EXPERIMENTAL feature so it shall not be used on production + * machines. Enabling this will allow you to send and receive I2C data from slave + * devices on the bus. + * + * ; Example #1 + * ; This macro send the string "Marlin" to the slave device with address 0x63 (99) + * ; It uses multiple M260 commands with one B arg + * M260 A99 ; Target slave address + * M260 B77 ; M + * M260 B97 ; a + * M260 B114 ; r + * M260 B108 ; l + * M260 B105 ; i + * M260 B110 ; n + * M260 S1 ; Send the current buffer + * + * ; Example #2 + * ; Request 6 bytes from slave device with address 0x63 (99) + * M261 A99 B5 + * + * ; Example #3 + * ; Example serial output of a M261 request + * echo:i2c-reply: from:99 bytes:5 data:hello + */ + +// @section i2cbus + +//#define EXPERIMENTAL_I2CBUS +#define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave + +// @section extras + +/** + * Photo G-code + * Add the M240 G-code to take a photo. + * The photo can be triggered by a digital pin or a physical movement. + */ +//#define PHOTO_GCODE +#if ENABLED(PHOTO_GCODE) + // A position to move to (and raise Z) before taking the photo + //#define PHOTO_POSITION { X_MAX_POS - 5, Y_MAX_POS, 0 } // { xpos, ypos, zraise } (M240 X Y Z) + //#define PHOTO_DELAY_MS 100 // (ms) Duration to pause before moving back (M240 P) + //#define PHOTO_RETRACT_MM 6.5 // (mm) E retract/recover for the photo move (M240 R S) + + // Canon RC-1 or homebrew digital camera trigger + // Data from: http://www.doc-diy.net/photo/rc-1_hacked/ + //#define PHOTOGRAPH_PIN 23 + + // Canon Hack Development Kit + // http://captain-slow.dk/2014/03/09/3d-printing-timelapses/ + //#define CHDK_PIN 4 + + // Optional second move with delay to trigger the camera shutter + //#define PHOTO_SWITCH_POSITION { X_MAX_POS, Y_MAX_POS } // { xpos, ypos } (M240 I J) + + // Duration to hold the switch or keep CHDK_PIN high + //#define PHOTO_SWITCH_MS 50 // (ms) (M240 D) +#endif + +/** + * Spindle & Laser control + * + * Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and + * to set spindle speed, spindle direction, and laser power. + * + * SuperPid is a router/spindle speed controller used in the CNC milling community. + * Marlin can be used to turn the spindle on and off. It can also be used to set + * the spindle speed from 5,000 to 30,000 RPM. + * + * You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V + * hardware PWM pin for the speed control and a pin for the rotation direction. + * + * See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details. + */ +//#define SPINDLE_FEATURE +//#define LASER_FEATURE +#if EITHER(SPINDLE_FEATURE, LASER_FEATURE) + #define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH + #define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power + #define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower + #define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power + #define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop + + #if ENABLED(SPINDLE_FEATURE) + //#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction + #define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction + #define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed + + /** + * The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power + * + * SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT + * where PWM duty cycle varies from 0 to 255 + * + * set the following for your controller (ALL MUST BE SET) + */ + #define SPEED_POWER_SLOPE 118.4 + #define SPEED_POWER_INTERCEPT 0 + #define SPEED_POWER_MIN 5000 + #define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM + #else + #define SPEED_POWER_SLOPE 0.3922 + #define SPEED_POWER_INTERCEPT 0 + #define SPEED_POWER_MIN 10 + #define SPEED_POWER_MAX 100 // 0-100% + #endif +#endif + +/** + * Coolant Control + * + * Add the M7, M8, and M9 commands to turn mist or flood coolant on and off. + * + * Note: COOLANT_MIST_PIN and/or COOLANT_FLOOD_PIN must also be defined. + */ +//#define COOLANT_CONTROL +#if ENABLED(COOLANT_CONTROL) + #define COOLANT_MIST // Enable if mist coolant is present + #define COOLANT_FLOOD // Enable if flood coolant is present + #define COOLANT_MIST_INVERT false // Set "true" if the on/off function is reversed + #define COOLANT_FLOOD_INVERT false // Set "true" if the on/off function is reversed +#endif + +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define FILWIDTH_ERROR_MARGIN 1.0 // (mm) If a measurement differs too much from nominal width ignore it + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + +/** + * CNC Coordinate Systems + * + * Enables G53 and G54-G59.3 commands to select coordinate systems + * and G92.1 to reset the workspace to native machine space. + */ +//#define CNC_COORDINATE_SYSTEMS + +/** + * Auto-report temperatures with M155 S + */ +#define AUTO_REPORT_TEMPERATURES + +/** + * Include capabilities in M115 output + */ +#define EXTENDED_CAPABILITIES_REPORT + +/** + * Expected Printer Check + * Add the M16 G-code to compare a string to the MACHINE_NAME. + * M16 with a non-matching string causes the printer to halt. + */ +//#define EXPECTED_PRINTER_CHECK + +/** + * Disable all Volumetric extrusion options + */ +//#define NO_VOLUMETRICS + +#if DISABLED(NO_VOLUMETRICS) + /** + * Volumetric extrusion default state + * Activate to make volumetric extrusion the default method, + * with DEFAULT_NOMINAL_FILAMENT_DIA as the default diameter. + * + * M200 D0 to disable, M200 Dn to set a new diameter. + */ + //#define VOLUMETRIC_DEFAULT_ON +#endif + +/** + * Enable this option for a leaner build of Marlin that removes all + * workspace offsets, simplifying coordinate transformations, leveling, etc. + * + * - M206 and M428 are disabled. + * - G92 will revert to its behavior from Marlin 1.0. + */ +//#define NO_WORKSPACE_OFFSETS + +/** + * Set the number of proportional font spaces required to fill up a typical character space. + * This can help to better align the output of commands like `G29 O` Mesh Output. + * + * For clients that use a fixed-width font (like OctoPrint), leave this set to 1.0. + * Otherwise, adjust according to your client and font. + */ +#define PROPORTIONAL_FONT_RATIO 1.0 + +/** + * Spend 28 bytes of SRAM to optimize the GCode parser + */ +#define FASTER_GCODE_PARSER + +/** + * CNC G-code options + * Support CNC-style G-code dialects used by laser cutters, drawing machine cams, etc. + * Note that G0 feedrates should be used with care for 3D printing (if used at all). + * High feedrates may cause ringing and harm print quality. + */ +//#define PAREN_COMMENTS // Support for parentheses-delimited comments +//#define GCODE_MOTION_MODES // Remember the motion mode (G0 G1 G2 G3 G5 G38.X) and apply for X Y Z E F, etc. + +// Enable and set a (default) feedrate for all G0 moves +//#define G0_FEEDRATE 3000 // (mm/m) +#ifdef G0_FEEDRATE + //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode +#endif + +/** + * Startup commands + * + * Execute certain G-code commands immediately after power-on. + */ +//#define STARTUP_COMMANDS "M17 Z" + +/** + * G-code Macros + * + * Add G-codes M810-M819 to define and run G-code macros. + * Macros are not saved to EEPROM. + */ +//#define GCODE_MACROS +#if ENABLED(GCODE_MACROS) + #define GCODE_MACROS_SLOTS 5 // Up to 10 may be used + #define GCODE_MACROS_SLOT_SIZE 50 // Maximum length of a single macro +#endif + +/** + * User-defined menu items that execute custom GCode + */ +//#define CUSTOM_USER_MENUS +#if ENABLED(CUSTOM_USER_MENUS) + //#define CUSTOM_USER_MENU_TITLE "Custom Commands" + #define USER_SCRIPT_DONE "M117 User Script Done" + #define USER_SCRIPT_AUDIBLE_FEEDBACK + //#define USER_SCRIPT_RETURN // Return to status screen after a script + + #define USER_DESC_1 "Home & UBL Info" + #define USER_GCODE_1 "G28\nG29 W" + + #define USER_DESC_2 "Preheat for " PREHEAT_1_LABEL + #define USER_GCODE_2 "M140 S" STRINGIFY(PREHEAT_1_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_1_TEMP_HOTEND) + + #define USER_DESC_3 "Preheat for " PREHEAT_2_LABEL + #define USER_GCODE_3 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_2_TEMP_HOTEND) + + #define USER_DESC_4 "Heat Bed/Home/Level" + #define USER_GCODE_4 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nG28\nG29" + + //#define USER_DESC_5 "Home & Info" + //#define USER_GCODE_5 "G28\nM503" +#endif + +/** + * Host Action Commands + * + * Define host streamer action commands in compliance with the standard. + * + * See https://reprap.org/wiki/G-code#Action_commands + * Common commands ........ poweroff, pause, paused, resume, resumed, cancel + * G29_RETRY_AND_RECOVER .. probe_rewipe, probe_failed + * + * Some features add reason codes to extend these commands. + * + * Host Prompt Support enables Marlin to use the host for user prompts so + * filament runout and other processes can be managed from the host side. + */ +//#define HOST_ACTION_COMMANDS +#if ENABLED(HOST_ACTION_COMMANDS) + //#define HOST_PROMPT_SUPPORT +#endif + +/** + * I2C position encoders for closed loop control. + * Developed by Chris Barr at Aus3D. + * + * Wiki: http://wiki.aus3d.com.au/Magnetic_Encoder + * Github: https://github.com/Aus3D/MagneticEncoder + * + * Supplier: http://aus3d.com.au/magnetic-encoder-module + * Alternative Supplier: http://reliabuild3d.com/ + * + * Reliabuild encoders have been modified to improve reliability. + */ + +//#define I2C_POSITION_ENCODERS +#if ENABLED(I2C_POSITION_ENCODERS) + + #define I2CPE_ENCODER_CNT 1 // The number of encoders installed; max of 5 + // encoders supported currently. + + #define I2CPE_ENC_1_ADDR I2CPE_PRESET_ADDR_X // I2C address of the encoder. 30-200. + #define I2CPE_ENC_1_AXIS X_AXIS // Axis the encoder module is installed on. _AXIS. + #define I2CPE_ENC_1_TYPE I2CPE_ENC_TYPE_LINEAR // Type of encoder: I2CPE_ENC_TYPE_LINEAR -or- + // I2CPE_ENC_TYPE_ROTARY. + #define I2CPE_ENC_1_TICKS_UNIT 2048 // 1024 for magnetic strips with 2mm poles; 2048 for + // 1mm poles. For linear encoders this is ticks / mm, + // for rotary encoders this is ticks / revolution. + //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper + // steps per full revolution (motor steps/rev * microstepping) + //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the + // printer will attempt to correct the error; errors + // smaller than this are ignored to minimize effects of + // measurement noise / latency (filter). + + #define I2CPE_ENC_2_ADDR I2CPE_PRESET_ADDR_Y // Same as above, but for encoder 2. + #define I2CPE_ENC_2_AXIS Y_AXIS + #define I2CPE_ENC_2_TYPE I2CPE_ENC_TYPE_LINEAR + #define I2CPE_ENC_2_TICKS_UNIT 2048 + //#define I2CPE_ENC_2_TICKS_REV (16 * 200) + //#define I2CPE_ENC_2_INVERT + #define I2CPE_ENC_2_EC_METHOD I2CPE_ECM_MICROSTEP + #define I2CPE_ENC_2_EC_THRESH 0.10 + + #define I2CPE_ENC_3_ADDR I2CPE_PRESET_ADDR_Z // Encoder 3. Add additional configuration options + #define I2CPE_ENC_3_AXIS Z_AXIS // as above, or use defaults below. + + #define I2CPE_ENC_4_ADDR I2CPE_PRESET_ADDR_E // Encoder 4. + #define I2CPE_ENC_4_AXIS E_AXIS + + #define I2CPE_ENC_5_ADDR 34 // Encoder 5. + #define I2CPE_ENC_5_AXIS E_AXIS + + // Default settings for encoders which are enabled, but without settings configured above. + #define I2CPE_DEF_TYPE I2CPE_ENC_TYPE_LINEAR + #define I2CPE_DEF_ENC_TICKS_UNIT 2048 + #define I2CPE_DEF_TICKS_REV (16 * 200) + #define I2CPE_DEF_EC_METHOD I2CPE_ECM_NONE + #define I2CPE_DEF_EC_THRESH 0.1 + + //#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given + // axis after which the printer will abort. Comment out to + // disable abort behavior. + + #define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault + // for this amount of time (in ms) before the encoder + // is trusted again. + + /** + * Position is checked every time a new command is executed from the buffer but during long moves, + * this setting determines the minimum update time between checks. A value of 100 works well with + * error rolling average when attempting to correct only for skips and not for vibration. + */ + #define I2CPE_MIN_UPD_TIME_MS 4 // (ms) Minimum time between encoder checks. + + // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise. + #define I2CPE_ERR_ROLLING_AVERAGE + +#endif // I2C_POSITION_ENCODERS + +/** + * Analog Joystick(s) + */ +//#define JOYSTICK +#if ENABLED(JOYSTICK) + #define JOY_X_PIN 5 // RAMPS: Suggested pin A5 on AUX2 + #define JOY_Y_PIN 10 // RAMPS: Suggested pin A10 on AUX2 + #define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2 + #define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2 + + // Use M119 to find reasonable values after connecting your hardware: + #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max + #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 } + #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 } +#endif + +/** + * MAX7219 Debug Matrix + * + * Add support for a low-cost 8x8 LED Matrix based on the Max7219 chip as a realtime status display. + * Requires 3 signal wires. Some useful debug options are included to demonstrate its usage. + */ +//#define MAX7219_DEBUG +#if ENABLED(MAX7219_DEBUG) + #define MAX7219_CLK_PIN 64 + #define MAX7219_DIN_PIN 57 + #define MAX7219_LOAD_PIN 44 + + //#define MAX7219_GCODE // Add the M7219 G-code to control the LED matrix + #define MAX7219_INIT_TEST 2 // Do a test pattern at initialization (Set to 2 for spiral) + #define MAX7219_NUMBER_UNITS 1 // Number of Max7219 units in chain. + #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) + // connector at: right=0 bottom=-90 top=90 left=180 + //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side + + /** + * Sample debug features + * If you add more debug displays, be careful to avoid conflicts! + */ + #define MAX7219_DEBUG_PRINTER_ALIVE // Blink corner LED of 8x8 matrix to show that the firmware is functioning + #define MAX7219_DEBUG_PLANNER_HEAD 3 // Show the planner queue head position on this and the next LED matrix row + #define MAX7219_DEBUG_PLANNER_TAIL 5 // Show the planner queue tail position on this and the next LED matrix row + + #define MAX7219_DEBUG_PLANNER_QUEUE 0 // Show the current planner queue depth on this and the next LED matrix row + // If you experience stuttering, reboots, etc. this option can reveal how + // tweaks made to the configuration are affecting the printer in real-time. +#endif + +/** + * NanoDLP Sync support + * + * Add support for Synchronized Z moves when using with NanoDLP. G0/G1 axis moves will output "Z_move_comp" + * string to enable synchronization with DLP projector exposure. This change will allow to use + * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands + */ +//#define NANODLP_Z_SYNC +#if ENABLED(NANODLP_Z_SYNC) + //#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move. + // Default behavior is limited to Z axis only. +#endif + +/** + * WiFi Support (Espressif ESP32 WiFi) + */ +//#define WIFISUPPORT +#if ENABLED(WIFISUPPORT) + #define WIFI_SSID "Wifi SSID" + #define WIFI_PWD "Wifi Password" + //#define WEBSUPPORT // Start a webserver with auto-discovery + //#define OTASUPPORT // Support over-the-air firmware updates +#endif + +/** + * Prusa Multi-Material Unit v2 + * Enable in Configuration.h + */ +#if ENABLED(PRUSA_MMU2) + + // Serial port used for communication with MMU2. + // For AVR enable the UART port used for the MMU. (e.g., internalSerial) + // For 32-bit boards check your HAL for available serial ports. (e.g., Serial2) + #define INTERNAL_SERIAL_PORT 2 + #define MMU2_SERIAL internalSerial + + // Use hardware reset for MMU if a pin is defined for it + //#define MMU2_RST_PIN 23 + + // Enable if the MMU2 has 12V stepper motors (MMU2 Firmware 1.0.2 and up) + //#define MMU2_MODE_12V + + // G-code to execute when MMU2 F.I.N.D.A. probe detects filament runout + #define MMU2_FILAMENT_RUNOUT_SCRIPT "M600" + + // Add an LCD menu for MMU2 + //#define MMU2_MENUS + #if ENABLED(MMU2_MENUS) + // Settings for filament load / unload from the LCD menu. + // This is for Prusa MK3-style extruders. Customize for your hardware. + #define MMU2_FILAMENTCHANGE_EJECT_FEED 80.0 + #define MMU2_LOAD_TO_NOZZLE_SEQUENCE \ + { 7.2, 562 }, \ + { 14.4, 871 }, \ + { 36.0, 1393 }, \ + { 14.4, 871 }, \ + { 50.0, 198 } + + #define MMU2_RAMMING_SEQUENCE \ + { 1.0, 1000 }, \ + { 1.0, 1500 }, \ + { 2.0, 2000 }, \ + { 1.5, 3000 }, \ + { 2.5, 4000 }, \ + { -15.0, 5000 }, \ + { -14.0, 1200 }, \ + { -6.0, 600 }, \ + { 10.0, 700 }, \ + { -10.0, 400 }, \ + { -50.0, 2000 } + + #endif + + //#define MMU2_DEBUG // Write debug info to serial output + +#endif // PRUSA_MMU2 + +/** + * Advanced Print Counter settings + */ +#if ENABLED(PRINTCOUNTER) + #define SERVICE_WARNING_BUZZES 3 + // Activate up to 3 service interval watchdogs + //#define SERVICE_NAME_1 "Service S" + //#define SERVICE_INTERVAL_1 100 // print hours + //#define SERVICE_NAME_2 "Service L" + //#define SERVICE_INTERVAL_2 200 // print hours + //#define SERVICE_NAME_3 "Service 3" + //#define SERVICE_INTERVAL_3 1 // print hours +#endif + +// @section develop + +/** + * M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins + */ +//#define PINS_DEBUGGING + +// Enable Marlin dev mode which adds some special commands +//#define MARLIN_DEV_MODE diff --git a/config/examples/Felix/Single/README.md b/config/examples/Felix/Single/README.md new file mode 100644 index 0000000000..48fe099151 --- /dev/null +++ b/config/examples/Felix/Single/README.md @@ -0,0 +1,60 @@ +# Felix 2.0/3.0 Configuration for Marlin Firmware + +Bringing silky smooth prints to Felix. + +## Build HOWTO + + - Install the latest non-beta Arduino software IDE/toolset: http://www.arduino.cc/en/Main/Software + - Download the Marlin firmware + - [Latest developement version](https://github.com/MarlinFirmware/Marlin/tree/Development) + - [Stable version](https://github.com/MarlinFirmware/Marlin/tree/Development) + - In both cases use the "Download Zip" button on the right. + +``` +cd Marlin/src +cp config/examples/Felix/Configuration_adv.h . +``` + +The next step depends on your setup: + +### Single Extruder Configuration + + cp config/examples/Felix/Configuration.h . + +### Dual Extruder Configuration + + cp config/examples/Felix/DUAL/Configuration.h Configuration.h + +### Compile Firmware + + - Start the Arduino IDE. + - Select Tools -> Board -> Arduino Mega 2560 + - Select the correct serial port in Tools -> Serial Port (usually /dev/ttyUSB0) + - Open Marlin.pde or .ino + - Click the Verify/Compile button + +### Flash Firmware + +#### Connected directly via USB + + - Click the Upload button. If all goes well the firmware is uploading + +#### Remote update + +Find the latest Arduino build: + + ls -altr /tmp/ + drwxr-xr-x 5 chrono users 12288 Mar 3 21:41 build6072035599686630843.tmp + +Copy the firmware to your printer host: + + scp /tmp/build6072035599686630843.tmp/Marlin.cpp.hex a.b.c.d:/tmp/ + +Connect to your printer host via ssh, stop Octoprint or any other service that may block your USB device and make sure you have avrdude installed, then run: + + avrdude -C/etc/avrdude.conf -v -v -v -patmega2560 -cwiring -P/dev/ttyUSB0 \ + -b115200 -D -Uflash:w:/tmp/Marlin.cpp.hex:i + +## Acknowledgements + +Mashed together and tested on https://apollo.open-resource.org/mission:resources:picoprint based on collaborative teamwork of @andrewsil1 and @thinkyhead. diff --git a/config/examples/Geeetech/Prusa i3 Pro B/README.md b/config/examples/Geeetech/Prusa i3 Pro B/bltouch/README.md similarity index 100% rename from config/examples/Geeetech/Prusa i3 Pro B/README.md rename to config/examples/Geeetech/Prusa i3 Pro B/bltouch/README.md diff --git a/config/examples/Geeetech/Prusa i3 Pro B/noprobe/README.md b/config/examples/Geeetech/Prusa i3 Pro B/noprobe/README.md new file mode 100644 index 0000000000..30fcf2e443 --- /dev/null +++ b/config/examples/Geeetech/Prusa i3 Pro B/noprobe/README.md @@ -0,0 +1,54 @@ +These are example configurations for the low-cost [Acrylic Prusa I3 pro B 3D Printer DIY kit](http://www.geeetech.com/acrylic-geeetech-prusa-i3-pro-b-3d-printer-diy-kit-p-917.html) and the [3DTouch auto bed leveling sensor](http://www.geeetech.com/geeetech-3dtouch-auto-bed-leveling-sensor-for-3d-printer-p-1010.html) based on: + +- `../GT2560/` +- [Marlin 1.1.4 With 3DTouch / BLTouch for i3 Pro B](https://www.geeetech.com/forum/viewtopic.php?t=19846) + +The main characteristics of these configurations are: + +- The defined motherboard is `BOARD_GT2560_REV_A_PLUS`. +- Travel limits are adjusted to the printer bed size and position. +- An example `SKEW_CORRECTION` for a particular printer is enabled. See comments below about how to adjust it to a particular printer. +- Using the LCD controller for bed leveling is enabled. + - `PROBE_MANUALLY` is enabled, which *provides a means to do "Auto" Bed Leveling without a probe*. + - The `LEVEL_BED_CORNERS` option for manual bed adjustment is enabled. + - Bilinear bed leveling is enabled, the boundaries for probing are adjusted to the glass size, and extrapolation is enabled. +- `PRINTCOUNTER` is enabled, in order to track statistical data. +- `INDIVIDUAL_AXIS_HOMING_MENU` is enabled, which adds individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu. +- The speaker is enabled for the UI feedback. +- `bltouch` variant: + - `USE_ZMAX_PLUG` is enabled. See comments about connections below. + - Heaters and fans are turned off when probing. + - Multiple probing is set to 3. + +# First-time configuration + +## Skew factor + +The skew factor must be adjusted for each printer: + +- First, uncomment `#define XY_SKEW_FACTOR 0.0`, compile and upload the firmware. +- Then, print [YACS (Yet Another Calibration Square)](https://www.thingiverse.com/thing:2563185). Hint, scale it considering a margin for brim (if used). The larger, the better to make error measurements. +- Measure the printed part according to the comments in the example configuration file, and set `XY_DIAG_AC`, `XY_DIAG_BD` and `Y_SIDE_AD`. +- Last, comment `#define XY_SKEW_FACTOR 0.0` again, compile and upload. + +## 3DTouch auto leveling sensor + +- Print a suitable mount to attach the sensor to the printer. The example configuration file is adjusted to http://www.geeetech.com/wiki/images/6/61/3DTouch_auto_leveling_sensor-1.zip +- Unlike suggested in [geeetech.com/wiki/index.php/3DTouch_Auto_Leveling_Sensor](https://www.geeetech.com/wiki/index.php/3DTouch_Auto_Leveling_Sensor), the existing end stop switch is expected to be kept connected to Z_MIN. So, the sensor is to be connected to Z_MAX, according to Marlin's default settings. Furthermore, GT2560-A+ provides a connector for the servo next to thermistor connectors (see [GT2560](https://www.geeetech.com/wiki/images/thumb/4/45/GT2560_wiring.jpg/700px-GT2560_wiring.jpg) and [GT2560-A+](http://i.imgur.com/E0t34VU.png)). +- Be careful to respect the polarity of the sensor when connecting it to the GT2560-A+. Unlike end stops, reversing the connection will prevent the sensor from working properly. +- [Test](http://www.geeetech.com/wiki/index.php/3DTouch_Auto_Leveling_Sensor#Testing) and [calibrate](https://www.geeetech.com/wiki/index.php/3DTouch_Auto_Leveling_Sensor#Calibration) the sensor. +- If using the GT2560-A+ and with the sensor connected to Z_MAX and an endstop connected to Z_MIN use the following calibration routine instead. + +## 3DTouch Calibration with Z_MAX + +- Home the printer with `G28` command. +- Disable the Z axis software endstop with `M211 S0 Z0` +- Reset the probe Z_OFFSET with `M851 Z0` +- Move to the center of the bed with `G1 X100 Y100` +- Move Z incrementally until the nozzle is the correct height from the bed using a shim or piece of paper, record this Z movement, for example -0.2. +- Do a single probe at the current point in the middle of the bed using `G30` and not the returned value, for example 1.9. Invert this value, i.e. -1.9, and add it to the Z offset above, i.e. -0.2 in this example giving -2.1. +- Update the probe Z_OFFSET to this value using `M851` i.e. `M851 Z-2.1`. +- Re-enable software end-stops with `M211 S1 Z0` +- Save this value to the EEPROM with `M500`. +- Update the start G-Code in your slicer software to insert a `G29` after the last `G28`. +- Carefully test that the offset is correct in the first print. diff --git a/config/examples/Micromake/C1/README.md b/config/examples/Micromake/C1/basic/README.md similarity index 100% rename from config/examples/Micromake/C1/README.md rename to config/examples/Micromake/C1/basic/README.md diff --git a/config/examples/Micromake/C1/enhanced/README.md b/config/examples/Micromake/C1/enhanced/README.md new file mode 100644 index 0000000000..0111f6f00a --- /dev/null +++ b/config/examples/Micromake/C1/enhanced/README.md @@ -0,0 +1,15 @@ +# Micromake C1 + +### In the folder "basic" +Configuration files for Micromake C1 without mods + - English LCD 2X16 Characters + - Motors 16 STEPS + - No heated bed + - No probe, etc. + - Like a standard C1 as shipped by Micromake. + +### In the folder "enhanced" +Configuration files for Micromake C1 with… + - 128 STEPS configured with jumper on the motherboard (all open for 128 Steps). + - Capacitive Probe (Adjust offsets at your convenience) + - French language with no accents for Japanese LCD. diff --git a/config/examples/Mks/Sbase/000-README_RepRap_Discount_Full_Graphic_Smart_Controller.txt b/config/examples/Mks/Sbase/README.txt similarity index 100% rename from config/examples/Mks/Sbase/000-README_RepRap_Discount_Full_Graphic_Smart_Controller.txt rename to config/examples/Mks/Sbase/README.txt diff --git a/config/examples/Velleman/K8400/Configuration_adv.h b/config/examples/Velleman/K8400/Dual-head/Configuration_adv.h similarity index 100% rename from config/examples/Velleman/K8400/Configuration_adv.h rename to config/examples/Velleman/K8400/Dual-head/Configuration_adv.h diff --git a/config/examples/Velleman/K8400/README.md b/config/examples/Velleman/K8400/Dual-head/README.md similarity index 100% rename from config/examples/Velleman/K8400/README.md rename to config/examples/Velleman/K8400/Dual-head/README.md diff --git a/config/examples/Velleman/K8400/Configuration.h b/config/examples/Velleman/K8400/Single-head/Configuration.h similarity index 100% rename from config/examples/Velleman/K8400/Configuration.h rename to config/examples/Velleman/K8400/Single-head/Configuration.h diff --git a/config/examples/Velleman/K8400/Single-head/Configuration_adv.h b/config/examples/Velleman/K8400/Single-head/Configuration_adv.h new file mode 100644 index 0000000000..6d87bcdae5 --- /dev/null +++ b/config/examples/Velleman/K8400/Single-head/Configuration_adv.h @@ -0,0 +1,2764 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/** + * Configuration_adv.h + * + * Advanced settings. + * Only change these if you know exactly what you're doing. + * Some of these settings can damage your printer if improperly set! + * + * Basic settings can be found in Configuration.h + * + */ +#define CONFIGURATION_ADV_H_VERSION 020000 + +// @section temperature + +//=========================================================================== +//=============================Thermal Settings ============================ +//=========================================================================== + +// +// Custom Thermistor 1000 parameters +// +#if TEMP_SENSOR_0 == 1000 + #define HOTEND0_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND0_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND0_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_1 == 1000 + #define HOTEND1_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND1_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND1_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_2 == 1000 + #define HOTEND2_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND2_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND2_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_3 == 1000 + #define HOTEND3_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND3_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND3_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_4 == 1000 + #define HOTEND4_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND4_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND4_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_5 == 1000 + #define HOTEND5_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND5_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND5_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_BED == 1000 + #define BED_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define BED_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define BED_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_CHAMBER == 1000 + #define CHAMBER_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define CHAMBER_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define CHAMBER_BETA 3950 // Beta value +#endif + +// +// Hephestos 2 24V heated bed upgrade kit. +// https://store.bq.com/en/heated-bed-kit-hephestos2 +// +//#define HEPHESTOS2_HEATED_BED_KIT +#if ENABLED(HEPHESTOS2_HEATED_BED_KIT) + #undef TEMP_SENSOR_BED + #define TEMP_SENSOR_BED 70 + #define HEATER_BED_INVERTING true +#endif + +/** + * Heated Chamber settings + */ +#if TEMP_SENSOR_CHAMBER + #define CHAMBER_MINTEMP 5 + #define CHAMBER_MAXTEMP 60 + #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target + //#define CHAMBER_LIMIT_SWITCHING + //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin + //#define HEATER_CHAMBER_INVERTING false +#endif + +#if DISABLED(PIDTEMPBED) + #define BED_CHECK_INTERVAL 1000 // ms between checks in bang-bang control + #if ENABLED(BED_LIMIT_SWITCHING) + #define BED_HYSTERESIS 1 // Only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS + #endif +#endif + +/** + * Thermal Protection provides additional protection to your printer from damage + * and fire. Marlin always includes safe min and max temperature ranges which + * protect against a broken or disconnected thermistor wire. + * + * The issue: If a thermistor falls out, it will report the much lower + * temperature of the air in the room, and the the firmware will keep + * the heater on. + * + * The solution: Once the temperature reaches the target, start observing. + * If the temperature stays too far below the target (hysteresis) for too + * long (period), the firmware will halt the machine as a safety precaution. + * + * If you get false positives for "Thermal Runaway", increase + * THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD + */ +#if ENABLED(THERMAL_PROTECTION_HOTENDS) + #define THERMAL_PROTECTION_PERIOD 40 // Seconds + #define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius + + //#define ADAPTIVE_FAN_SLOWING // Slow part cooling fan if temperature drops + #if BOTH(ADAPTIVE_FAN_SLOWING, PIDTEMP) + //#define NO_FAN_SLOWING_IN_PID_TUNING // Don't slow fan speed during M303 + #endif + + /** + * Whenever an M104, M109, or M303 increases the target temperature, the + * firmware will wait for the WATCH_TEMP_PERIOD to expire. If the temperature + * hasn't increased by WATCH_TEMP_INCREASE degrees, the machine is halted and + * requires a hard reset. This test restarts with any M104/M109/M303, but only + * if the current temperature is far enough below the target for a reliable + * test. + * + * If you get false positives for "Heating failed", increase WATCH_TEMP_PERIOD + * and/or decrease WATCH_TEMP_INCREASE. WATCH_TEMP_INCREASE should not be set + * below 2. + */ + #define WATCH_TEMP_PERIOD 20 // Seconds + #define WATCH_TEMP_INCREASE 2 // Degrees Celsius +#endif + +/** + * Thermal Protection parameters for the bed are just as above for hotends. + */ +#if ENABLED(THERMAL_PROTECTION_BED) + #define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds + #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius + + /** + * As described above, except for the bed (M140/M190/M303). + */ + #define WATCH_BED_TEMP_PERIOD 60 // Seconds + #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius +#endif + +/** + * Thermal Protection parameters for the heated chamber. + */ +#if ENABLED(THERMAL_PROTECTION_CHAMBER) + #define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds + #define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius + + /** + * Heated chamber watch settings (M141/M191). + */ + #define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds + #define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius +#endif + +#if ENABLED(PIDTEMP) + // Add an experimental additional term to the heater power, proportional to the extrusion speed. + // A well-chosen Kc value should add just enough power to melt the increased material volume. + //#define PID_EXTRUSION_SCALING + #if ENABLED(PID_EXTRUSION_SCALING) + #define DEFAULT_Kc (100) //heating power=Kc*(e_speed) + #define LPQ_MAX_LEN 50 + #endif +#endif + +/** + * Automatic Temperature: + * The hotend target temperature is calculated by all the buffered lines of gcode. + * The maximum buffered steps/sec of the extruder motor is called "se". + * Start autotemp mode with M109 S B F + * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by + * mintemp and maxtemp. Turn this off by executing M109 without F* + * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp. + * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode + */ +#define AUTOTEMP +#if ENABLED(AUTOTEMP) + #define AUTOTEMP_OLDWEIGHT 0.98 +#endif + +// Show extra position information with 'M114 D' +//#define M114_DETAIL + +// Show Temperature ADC value +// Enable for M105 to include ADC values read from temperature sensors. +//#define SHOW_TEMP_ADC_VALUES + +/** + * High Temperature Thermistor Support + * + * Thermistors able to support high temperature tend to have a hard time getting + * good readings at room and lower temperatures. This means HEATER_X_RAW_LO_TEMP + * will probably be caught when the heating element first turns on during the + * preheating process, which will trigger a min_temp_error as a safety measure + * and force stop everything. + * To circumvent this limitation, we allow for a preheat time (during which, + * min_temp_error won't be triggered) and add a min_temp buffer to handle + * aberrant readings. + * + * If you want to enable this feature for your hotend thermistor(s) + * uncomment and set values > 0 in the constants below + */ + +// The number of consecutive low temperature errors that can occur +// before a min_temp_error is triggered. (Shouldn't be more than 10.) +//#define MAX_CONSECUTIVE_LOW_TEMPERATURE_ERROR_ALLOWED 0 + +// The number of milliseconds a hotend will preheat before starting to check +// the temperature. This value should NOT be set to the time it takes the +// hot end to reach the target temperature, but the time it takes to reach +// the minimum temperature your thermistor can read. The lower the better/safer. +// This shouldn't need to be more than 30 seconds (30000) +//#define MILLISECONDS_PREHEAT_TIME 0 + +// @section extruder + +// Extruder runout prevention. +// If the machine is idle and the temperature over MINTEMP +// then extrude some filament every couple of SECONDS. +//#define EXTRUDER_RUNOUT_PREVENT +#if ENABLED(EXTRUDER_RUNOUT_PREVENT) + #define EXTRUDER_RUNOUT_MINTEMP 190 + #define EXTRUDER_RUNOUT_SECONDS 30 + #define EXTRUDER_RUNOUT_SPEED 1500 // (mm/m) + #define EXTRUDER_RUNOUT_EXTRUDE 5 // (mm) +#endif + +// @section temperature + +// Calibration for AD595 / AD8495 sensor to adjust temperature measurements. +// The final temperature is calculated as (measuredTemp * GAIN) + OFFSET. +#define TEMP_SENSOR_AD595_OFFSET 0.0 +#define TEMP_SENSOR_AD595_GAIN 1.0 +#define TEMP_SENSOR_AD8495_OFFSET 0.0 +#define TEMP_SENSOR_AD8495_GAIN 1.0 + +/** + * Controller Fan + * To cool down the stepper drivers and MOSFETs. + * + * The fan will turn on automatically whenever any stepper is enabled + * and turn off after a set period after all steppers are turned off. + */ +#define USE_CONTROLLER_FAN +#if ENABLED(USE_CONTROLLER_FAN) + #define CONTROLLER_FAN_PIN 2 // Set a custom pin for the controller fan + #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled + #define CONTROLLERFAN_SPEED 255 // 255 == full speed + //#define CONTROLLERFAN_SPEED_Z_ONLY 127 // Reduce noise on machines that keep Z enabled +#endif + +// When first starting the main fan, run it at full speed for the +// given number of milliseconds. This gets the fan spinning reliably +// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) +//#define FAN_KICKSTART_TIME 100 + +/** + * PWM Fan Scaling + * + * Define the min/max speeds for PWM fans (as set with M106). + * + * With these options the M106 0-255 value range is scaled to a subset + * to ensure that the fan has enough power to spin, or to run lower + * current fans with higher current. (e.g., 5V/12V fans with 12V/24V) + * Value 0 always turns off the fan. + * + * Define one or both of these to override the default 0-255 range. + */ +//#define FAN_MIN_PWM 50 +//#define FAN_MAX_PWM 128 + +/** + * FAST PWM FAN Settings + * + * Use to change the FAST FAN PWM frequency (if enabled in Configuration.h) + * Combinations of PWM Modes, prescale values and TOP resolutions are used internally to produce a + * frequency as close as possible to the desired frequency. + * + * FAST_PWM_FAN_FREQUENCY [undefined by default] + * Set this to your desired frequency. + * If left undefined this defaults to F = F_CPU/(2*255*1) + * ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers + * These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required + * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior. + * + * USE_OCR2A_AS_TOP [undefined by default] + * Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2: + * 16MHz MCUs: [62.5KHz, 31.4KHz (default), 7.8KHz, 3.92KHz, 1.95KHz, 977Hz, 488Hz, 244Hz, 60Hz, 122Hz, 30Hz] + * 20MHz MCUs: [78.1KHz, 39.2KHz (default), 9.77KHz, 4.9KHz, 2.44KHz, 1.22KHz, 610Hz, 305Hz, 153Hz, 76Hz, 38Hz] + * A greater range can be achieved by enabling USE_OCR2A_AS_TOP. But note that this option blocks the use of + * PWM on pin OC2A. Only use this option if you don't need PWM on 0C2A. (Check your schematic.) + * USE_OCR2A_AS_TOP sacrifices duty cycle control resolution to achieve this broader range of frequencies. + */ +#if ENABLED(FAST_PWM_FAN) + //#define FAST_PWM_FAN_FREQUENCY 31400 + //#define USE_OCR2A_AS_TOP +#endif + +// @section extruder + +/** + * Extruder cooling fans + * + * Extruder auto fans automatically turn on when their extruders' + * temperatures go above EXTRUDER_AUTO_FAN_TEMPERATURE. + * + * Your board's pins file specifies the recommended pins. Override those here + * or set to -1 to disable completely. + * + * Multiple extruders can be assigned to the same pin in which case + * the fan will turn on when any selected extruder is above the threshold. + */ +#define E0_AUTO_FAN_PIN -1 +#define E1_AUTO_FAN_PIN -1 +#define E2_AUTO_FAN_PIN -1 +#define E3_AUTO_FAN_PIN -1 +#define E4_AUTO_FAN_PIN -1 +#define E5_AUTO_FAN_PIN -1 +#define CHAMBER_AUTO_FAN_PIN -1 + +#define EXTRUDER_AUTO_FAN_TEMPERATURE 50 +#define EXTRUDER_AUTO_FAN_SPEED 255 // 255 == full speed +#define CHAMBER_AUTO_FAN_TEMPERATURE 30 +#define CHAMBER_AUTO_FAN_SPEED 255 + +/** + * Part-Cooling Fan Multiplexer + * + * This feature allows you to digitally multiplex the fan output. + * The multiplexer is automatically switched at tool-change. + * Set FANMUX[012]_PINs below for up to 2, 4, or 8 multiplexed fans. + */ +#define FANMUX0_PIN -1 +#define FANMUX1_PIN -1 +#define FANMUX2_PIN -1 + +/** + * M355 Case Light on-off / brightness + */ +//#define CASE_LIGHT_ENABLE +#if ENABLED(CASE_LIGHT_ENABLE) + //#define CASE_LIGHT_PIN 4 // Override the default pin if needed + #define INVERT_CASE_LIGHT false // Set true if Case Light is ON when pin is LOW + #define CASE_LIGHT_DEFAULT_ON true // Set default power-up state on + #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105 // Set default power-up brightness (0-255, requires PWM pin) + //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu + //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. + //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) + #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } + #endif +#endif + +// @section homing + +// If you want endstops to stay on (by default) even when not homing +// enable this option. Override at any time with M120, M121. +//#define ENDSTOPS_ALWAYS_ON_DEFAULT + +// @section extras + +//#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats. + +// Employ an external closed loop controller. Override pins here if needed. +//#define EXTERNAL_CLOSED_LOOP_CONTROLLER +#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER) + //#define CLOSED_LOOP_ENABLE_PIN -1 + //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1 +#endif + +/** + * Dual Steppers / Dual Endstops + * + * This section will allow you to use extra E drivers to drive a second motor for X, Y, or Z axes. + * + * For example, set X_DUAL_STEPPER_DRIVERS setting to use a second motor. If the motors need to + * spin in opposite directions set INVERT_X2_VS_X_DIR. If the second motor needs its own endstop + * set X_DUAL_ENDSTOPS. This can adjust for "racking." Use X2_USE_ENDSTOP to set the endstop plug + * that should be used for the second endstop. Extra endstops will appear in the output of 'M119'. + * + * Use X_DUAL_ENDSTOP_ADJUSTMENT to adjust for mechanical imperfection. After homing both motors + * this offset is applied to the X2 motor. To find the offset home the X axis, and measure the error + * in X2. Dual endstop offsets can be set at runtime with 'M666 X Y Z'. + */ + +//#define X_DUAL_STEPPER_DRIVERS +#if ENABLED(X_DUAL_STEPPER_DRIVERS) + #define INVERT_X2_VS_X_DIR true // Set 'true' if X motors should rotate in opposite directions + //#define X_DUAL_ENDSTOPS + #if ENABLED(X_DUAL_ENDSTOPS) + #define X2_USE_ENDSTOP _XMAX_ + #define X_DUAL_ENDSTOPS_ADJUSTMENT 0 + #endif +#endif + +//#define Y_DUAL_STEPPER_DRIVERS +#if ENABLED(Y_DUAL_STEPPER_DRIVERS) + #define INVERT_Y2_VS_Y_DIR true // Set 'true' if Y motors should rotate in opposite directions + //#define Y_DUAL_ENDSTOPS + #if ENABLED(Y_DUAL_ENDSTOPS) + #define Y2_USE_ENDSTOP _YMAX_ + #define Y_DUAL_ENDSTOPS_ADJUSTMENT 0 + #endif +#endif + +//#define Z_DUAL_STEPPER_DRIVERS +#if ENABLED(Z_DUAL_STEPPER_DRIVERS) + //#define Z_DUAL_ENDSTOPS + #if ENABLED(Z_DUAL_ENDSTOPS) + #define Z2_USE_ENDSTOP _XMAX_ + #define Z_DUAL_ENDSTOPS_ADJUSTMENT 0 + #endif +#endif + +//#define Z_TRIPLE_STEPPER_DRIVERS +#if ENABLED(Z_TRIPLE_STEPPER_DRIVERS) + //#define Z_TRIPLE_ENDSTOPS + #if ENABLED(Z_TRIPLE_ENDSTOPS) + #define Z2_USE_ENDSTOP _XMAX_ + #define Z3_USE_ENDSTOP _YMAX_ + #define Z_TRIPLE_ENDSTOPS_ADJUSTMENT2 0 + #define Z_TRIPLE_ENDSTOPS_ADJUSTMENT3 0 + #endif +#endif + +/** + * Dual X Carriage + * + * This setup has two X carriages that can move independently, each with its own hotend. + * The carriages can be used to print an object with two colors or materials, or in + * "duplication mode" it can print two identical or X-mirrored objects simultaneously. + * The inactive carriage is parked automatically to prevent oozing. + * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. + * By default the X2 stepper is assigned to the first unused E plug on the board. + * + * The following Dual X Carriage modes can be selected with M605 S: + * + * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel + * results as long as it supports dual X-carriages. (M605 S0) + * + * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so + * that additional slicer support is not required. (M605 S1) + * + * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with + * the first X-carriage and extruder, to print 2 copies of the same object at the same time. + * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and + * follow with M605 S2 to initiate duplicated movement. + * + * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates + * the movement of the first except the second extruder is reversed in the X axis. + * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and + * follow with M605 S3 to initiate mirrored movement. + */ +//#define DUAL_X_CARRIAGE +#if ENABLED(DUAL_X_CARRIAGE) + #define X1_MIN_POS X_MIN_POS // Set to X_MIN_POS + #define X1_MAX_POS X_BED_SIZE // Set a maximum so the first X-carriage can't hit the parked second X-carriage + #define X2_MIN_POS 80 // Set a minimum to ensure the second X-carriage can't hit the parked first X-carriage + #define X2_MAX_POS 353 // Set this to the distance between toolheads when both heads are homed + #define X2_HOME_DIR 1 // Set to 1. The second X-carriage always homes to the maximum endstop position + #define X2_HOME_POS X2_MAX_POS // Default X2 home position. Set to X2_MAX_POS. + // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software + // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops + // without modifying the firmware (through the "M218 T1 X???" command). + // Remember: you should set the second extruder x-offset to 0 in your slicer. + + // This is the default power-up mode which can be later using M605. + #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_AUTO_PARK_MODE + + // Default x offset in duplication mode (typically set to half print bed width) + #define DEFAULT_DUPLICATION_X_OFFSET 100 + +#endif // DUAL_X_CARRIAGE + +// Activate a solenoid on the active extruder with M380. Disable all with M381. +// Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid. +//#define EXT_SOLENOID + +// @section homing + +// Homing hits each endstop, retracts by these distances, then does a slower bump. +#define X_HOME_BUMP_MM 10 +#define Y_HOME_BUMP_MM 10 +#define Z_HOME_BUMP_MM 3 +#define HOMING_BUMP_DIVISOR { 2, 2, 4 } // Re-Bump Speed Divisor (Divides the Homing Feedrate) +#define QUICK_HOME // If homing includes X and Y, do a diagonal move initially +//#define HOMING_BACKOFF_MM { 2, 2, 2 } // (mm) Move away from the endstops after homing + +// When G28 is called, this option will make Y home before X +//#define HOME_Y_BEFORE_X + +// Enable this if X or Y can't home without homing the other axis first. +//#define CODEPENDENT_XY_HOMING + +#if ENABLED(BLTOUCH) + /** + * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES + * Do not activate settings that the probe might not understand. Clones might misunderstand + * advanced commands. + * + * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then + * check the wiring of the BROWN, RED and ORANGE wires. + * + * Note: If the trigger signal of your probe is not being recognized, it has been very often + * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable" + * like they would be with a real switch. So please check the wiring first. + * + * Settings for all BLTouch and clone probes: + */ + + // Safety: The probe needs time to recognize the command. + // Minimum command delay (ms). Enable and increase if needed. + //#define BLTOUCH_DELAY 500 + + /** + * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones: + */ + + // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful + // in special cases, like noisy or filtered input configurations. + //#define BLTOUCH_FORCE_SW_MODE + + /** + * Settings for BLTouch Smart 3.0 and 3.1 + * Summary: + * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes + * - High-Speed mode + * - Disable LCD voltage options + */ + + /** + * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller! + * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup. + * If disabled, OD mode is the hard-coded default on 3.0 + * On startup, Marlin will compare its eeprom to this vale. If the selected mode + * differs, a mode set eeprom write will be completed at initialization. + * Use the option below to force an eeprom write to a V3.1 probe regardless. + */ + //#define BLTOUCH_SET_5V_MODE + + /** + * Safety: Activate if connecting a probe with an unknown voltage mode. + * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0 + * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write ) + * To preserve the life of the probe, use this once then turn it off and re-flash. + */ + //#define BLTOUCH_FORCE_MODE_SET + + /** + * Use "HIGH SPEED" mode for probing. + * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems. + * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function + * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state. + */ + //#define BLTOUCH_HS_MODE + + // Safety: Enable voltage mode settings in the LCD menu. + //#define BLTOUCH_LCD_VOLTAGE_MENU + +#endif // BLTOUCH + +/** + * Z Steppers Auto-Alignment + * Add the G34 command to align multiple Z steppers using a bed probe. + */ +//#define Z_STEPPER_AUTO_ALIGN +#if ENABLED(Z_STEPPER_AUTO_ALIGN) + // Define probe X and Y positions for Z1, Z2 [, Z3] + #define Z_STEPPER_ALIGN_XY { { 10, 290 }, { 150, 10 }, { 290, 290 } } // Set number of iterations to align + #define Z_STEPPER_ALIGN_ITERATIONS 3 + // Enable to restore leveling setup after operation + #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + + // Use the amplification factor to de-/increase correction step. + // In case the stepper (spindle) position is further out than the test point + // Use a value > 1. NOTE: This may cause instability + #define Z_STEPPER_ALIGN_AMP 1.0 + // Stop criterion. If the accuracy is better than this stop iterating early + #define Z_STEPPER_ALIGN_ACC 0.02 +#endif + +// @section motion + +#define AXIS_RELATIVE_MODES { false, false, false, false } + +// Add a Duplicate option for well-separated conjoined nozzles +//#define MULTI_NOZZLE_DUPLICATION + +// By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step. +#define INVERT_X_STEP_PIN false +#define INVERT_Y_STEP_PIN false +#define INVERT_Z_STEP_PIN false +#define INVERT_E_STEP_PIN false + +// Default stepper release if idle. Set to 0 to deactivate. +// Steppers will shut down DEFAULT_STEPPER_DEACTIVE_TIME seconds after the last move when DISABLE_INACTIVE_? is true. +// Time can be set by M18 and M84. +#define DEFAULT_STEPPER_DEACTIVE_TIME 120 +#define DISABLE_INACTIVE_X true +#define DISABLE_INACTIVE_Y true +#define DISABLE_INACTIVE_Z true // Set to false if the nozzle will fall down on your printed part when print has finished. +#define DISABLE_INACTIVE_E true + +#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate +#define DEFAULT_MINTRAVELFEEDRATE 0.0 + +//#define HOME_AFTER_DEACTIVATE // Require rehoming after steppers are deactivated + +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) + +// If defined the movements slow down when the look ahead buffer is only half full +#define SLOWDOWN + +// Frequency limit +// See nophead's blog for more info +// Not working O +//#define XY_FREQUENCY_LIMIT 15 + +// Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end +// of the buffer and all stops. This should not be much greater than zero and should only be changed +// if unwanted behavior is observed on a user's machine when running at very slow speeds. +#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s) + +// +// Backlash Compensation +// Adds extra movement to axes on direction-changes to account for backlash. +// +//#define BACKLASH_COMPENSATION +#if ENABLED(BACKLASH_COMPENSATION) + // Define values for backlash distance and correction. + // If BACKLASH_GCODE is enabled these values are the defaults. + #define BACKLASH_DISTANCE_MM { 0, 0, 0 } // (mm) + #define BACKLASH_CORRECTION 0.0 // 0.0 = no correction; 1.0 = full correction + + // Set BACKLASH_SMOOTHING_MM to spread backlash correction over multiple segments + // to reduce print artifacts. (Enabling this is costly in memory and computation!) + //#define BACKLASH_SMOOTHING_MM 3 // (mm) + + // Add runtime configuration and tuning of backlash values (M425) + //#define BACKLASH_GCODE + + #if ENABLED(BACKLASH_GCODE) + // Measure the Z backlash when probing (G29) and set with "M425 Z" + #define MEASURE_BACKLASH_WHEN_PROBING + + #if ENABLED(MEASURE_BACKLASH_WHEN_PROBING) + // When measuring, the probe will move up to BACKLASH_MEASUREMENT_LIMIT + // mm away from point of contact in BACKLASH_MEASUREMENT_RESOLUTION + // increments while checking for the contact to be broken. + #define BACKLASH_MEASUREMENT_LIMIT 0.5 // (mm) + #define BACKLASH_MEASUREMENT_RESOLUTION 0.005 // (mm) + #define BACKLASH_MEASUREMENT_FEEDRATE Z_PROBE_SPEED_SLOW // (mm/m) + #endif + #endif +#endif + +/** + * Automatic backlash, position and hotend offset calibration + * + * Enable G425 to run automatic calibration using an electrically- + * conductive cube, bolt, or washer mounted on the bed. + * + * G425 uses the probe to touch the top and sides of the calibration object + * on the bed and measures and/or correct positional offsets, axis backlash + * and hotend offsets. + * + * Note: HOTEND_OFFSET and CALIBRATION_OBJECT_CENTER must be set to within + * ±5mm of true values for G425 to succeed. + */ +//#define CALIBRATION_GCODE +#if ENABLED(CALIBRATION_GCODE) + + #define CALIBRATION_MEASUREMENT_RESOLUTION 0.01 // mm + + #define CALIBRATION_FEEDRATE_SLOW 60 // mm/m + #define CALIBRATION_FEEDRATE_FAST 1200 // mm/m + #define CALIBRATION_FEEDRATE_TRAVEL 3000 // mm/m + + // The following parameters refer to the conical section of the nozzle tip. + #define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm + #define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm + + // Uncomment to enable reporting (required for "G425 V", but consumes PROGMEM). + //#define CALIBRATION_REPORTING + + // The true location and dimension the cube/bolt/washer on the bed. + #define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // mm + #define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // mm + + // Comment out any sides which are unreachable by the probe. For best + // auto-calibration results, all sides must be reachable. + #define CALIBRATION_MEASURE_RIGHT + #define CALIBRATION_MEASURE_FRONT + #define CALIBRATION_MEASURE_LEFT + #define CALIBRATION_MEASURE_BACK + + // Probing at the exact top center only works if the center is flat. If + // probing on a screwhead or hollow washer, probe near the edges. + //#define CALIBRATION_MEASURE_AT_TOP_EDGES + + // Define pin which is read during calibration + #ifndef CALIBRATION_PIN + #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop + #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin + //#define CALIBRATION_PIN_PULLDOWN + #define CALIBRATION_PIN_PULLUP + #endif +#endif + +/** + * Adaptive Step Smoothing increases the resolution of multi-axis moves, particularly at step frequencies + * below 1kHz (for AVR) or 10kHz (for ARM), where aliasing between axes in multi-axis moves causes audible + * vibration and surface artifacts. The algorithm adapts to provide the best possible step smoothing at the + * lowest stepping frequencies. + */ +//#define ADAPTIVE_STEP_SMOOTHING + +/** + * Custom Microstepping + * Override as-needed for your setup. Up to 3 MS pins are supported. + */ +//#define MICROSTEP1 LOW,LOW,LOW +//#define MICROSTEP2 HIGH,LOW,LOW +//#define MICROSTEP4 LOW,HIGH,LOW +//#define MICROSTEP8 HIGH,HIGH,LOW +//#define MICROSTEP16 LOW,LOW,HIGH +//#define MICROSTEP32 HIGH,LOW,HIGH + +// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU. +#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16] + +/** + * @section stepper motor current + * + * Some boards have a means of setting the stepper motor current via firmware. + * + * The power on motor currents are set by: + * PWM_MOTOR_CURRENT - used by MINIRAMBO & ULTIMAIN_2 + * known compatible chips: A4982 + * DIGIPOT_MOTOR_CURRENT - used by BQ_ZUM_MEGA_3D, RAMBO & SCOOVO_X9H + * known compatible chips: AD5206 + * DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2 + * known compatible chips: MCP4728 + * DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, AZTEEG_X5_MINI_WIFI, MIGHTYBOARD_REVE + * known compatible chips: MCP4451, MCP4018 + * + * Motor currents can also be set by M907 - M910 and by the LCD. + * M907 - applies to all. + * M908 - BQ_ZUM_MEGA_3D, RAMBO, PRINTRBOARD_REVF, RIGIDBOARD_V2 & SCOOVO_X9H + * M909, M910 & LCD - only PRINTRBOARD_REVF & RIGIDBOARD_V2 + */ +//#define PWM_MOTOR_CURRENT { 1300, 1300, 1250 } // Values in milliamps +//#define DIGIPOT_MOTOR_CURRENT { 135,135,135,135,135 } // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A) +//#define DAC_MOTOR_CURRENT_DEFAULT { 70, 80, 90, 80 } // Default drive percent - X, Y, Z, E axis + +// Use an I2C based DIGIPOT (e.g., Azteeg X3 Pro) +//#define DIGIPOT_I2C +#if ENABLED(DIGIPOT_I2C) && !defined(DIGIPOT_I2C_ADDRESS_A) + /** + * Common slave addresses: + * + * A (A shifted) B (B shifted) IC + * Smoothie 0x2C (0x58) 0x2D (0x5A) MCP4451 + * AZTEEG_X3_PRO 0x2C (0x58) 0x2E (0x5C) MCP4451 + * AZTEEG_X5_MINI 0x2C (0x58) 0x2E (0x5C) MCP4451 + * AZTEEG_X5_MINI_WIFI 0x58 0x5C MCP4451 + * MIGHTYBOARD_REVE 0x2F (0x5E) MCP4018 + */ + #define DIGIPOT_I2C_ADDRESS_A 0x2C // unshifted slave address for first DIGIPOT + #define DIGIPOT_I2C_ADDRESS_B 0x2D // unshifted slave address for second DIGIPOT +#endif + +//#define DIGIPOT_MCP4018 // Requires library from https://github.com/stawel/SlowSoftI2CMaster +#define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT: 4 AZTEEG_X3_PRO: 8 MKS SBASE: 5 +// Actual motor currents in Amps. The number of entries must match DIGIPOT_I2C_NUM_CHANNELS. +// These correspond to the physical drivers, so be mindful if the order is changed. +#define DIGIPOT_I2C_MOTOR_CURRENTS { 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0 } // AZTEEG_X3_PRO + +//=========================================================================== +//=============================Additional Features=========================== +//=========================================================================== + +// @section lcd + +#if EITHER(ULTIPANEL, EXTENSIBLE_UI) + #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) + #if ENABLED(ULTIPANEL) + #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" + #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen + #endif +#endif + +// Change values more rapidly when the encoder is rotated faster +#define ENCODER_RATE_MULTIPLIER +#if ENABLED(ENCODER_RATE_MULTIPLIER) + #define ENCODER_10X_STEPS_PER_SEC 30 // (steps/s) Encoder rate for 10x speed + #define ENCODER_100X_STEPS_PER_SEC 80 // (steps/s) Encoder rate for 100x speed +#endif + +// Play a beep when the feedrate is changed from the Status Screen +//#define BEEP_ON_FEEDRATE_CHANGE +#if ENABLED(BEEP_ON_FEEDRATE_CHANGE) + #define FEEDRATE_CHANGE_BEEP_DURATION 10 + #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 +#endif + +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + // BACK menu items keep the highlight at the top + //#define TURBO_BACK_MENU_ITEM + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU + +// Scroll a longer status message into view +//#define STATUS_MESSAGE_SCROLLING + +// On the Info Screen, display XY with one decimal place when possible +//#define LCD_DECIMAL_SMALL_XY + +// The timeout (in ms) to return to the status screen from sub-menus +//#define LCD_TIMEOUT_TO_STATUS 15000 + +// Add an 'M73' G-code to set the current percentage +//#define LCD_SET_PROGRESS_MANUALLY + +#if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS + //#define LCD_PROGRESS_BAR // Show a progress bar on HD44780 LCDs for SD printing + #if ENABLED(LCD_PROGRESS_BAR) + #define PROGRESS_BAR_BAR_TIME 2000 // (ms) Amount of time to show the bar + #define PROGRESS_BAR_MSG_TIME 3000 // (ms) Amount of time to show the status message + #define PROGRESS_MSG_EXPIRE 0 // (ms) Amount of time to retain the status message (0=forever) + //#define PROGRESS_MSG_ONCE // Show the message for MSG_TIME then clear it + //#define LCD_PROGRESS_BAR_TEST // Add a menu item to test the progress bar + #endif +#endif + +#if ENABLED(SDSUPPORT) + + // Some RAMPS and other boards don't detect when an SD card is inserted. You can work + // around this by connecting a push button or single throw switch to the pin defined + // as SD_DETECT_PIN in your board's pins definitions. + // This setting should be disabled unless you are using a push button, pulling the pin to ground. + // Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER). + #define SD_DETECT_INVERTED + + #define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished + #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place. + + // Reverse SD sort to show "more recent" files first, according to the card's FAT. + // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended. + #define SDCARD_RATHERRECENTFIRST + + #define SD_MENU_CONFIRM_START // Confirm the selected SD file before printing + + //#define MENU_ADDAUTOSTART // Add a menu option to run auto#.g files + + #define EVENT_GCODE_SD_STOP "G28XY" // G-code to run on Stop Print (e.g., "G28XY" or "G27") + + /** + * Continue after Power-Loss (Creality3D) + * + * Store the current state to the SD Card at the start of each layer + * during SD printing. If the recovery file is found at boot time, present + * an option on the LCD screen to continue the print from the last-known + * point in the file. + */ + //#define POWER_LOSS_RECOVERY + #if ENABLED(POWER_LOSS_RECOVERY) + //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate + //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume + //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. + + // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, + // especially with "vase mode" printing. Set too high and vases cannot be continued. + #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + #endif + + /** + * Sort SD file listings in alphabetical order. + * + * With this option enabled, items on SD cards will be sorted + * by name for easier navigation. + * + * By default... + * + * - Use the slowest -but safest- method for sorting. + * - Folders are sorted to the top. + * - The sort key is statically allocated. + * - No added G-code (M34) support. + * - 40 item sorting limit. (Items after the first 40 are unsorted.) + * + * SD sorting uses static allocation (as set by SDSORT_LIMIT), allowing the + * compiler to calculate the worst-case usage and throw an error if the SRAM + * limit is exceeded. + * + * - SDSORT_USES_RAM provides faster sorting via a static directory buffer. + * - SDSORT_USES_STACK does the same, but uses a local stack-based buffer. + * - SDSORT_CACHE_NAMES will retain the sorted file listing in RAM. (Expensive!) + * - SDSORT_DYNAMIC_RAM only uses RAM when the SD menu is visible. (Use with caution!) + */ + //#define SDCARD_SORT_ALPHA + + // SD Card Sorting options + #if ENABLED(SDCARD_SORT_ALPHA) + #define SDSORT_LIMIT 40 // Maximum number of sorted items (10-256). Costs 27 bytes each. + #define FOLDER_SORTING -1 // -1=above 0=none 1=below + #define SDSORT_GCODE false // Allow turning sorting on/off with LCD and M34 g-code. + #define SDSORT_USES_RAM false // Pre-allocate a static array for faster pre-sorting. + #define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.) + #define SDSORT_CACHE_NAMES false // Keep sorted items in RAM longer for speedy performance. Most expensive option. + #define SDSORT_DYNAMIC_RAM false // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use! + #define SDSORT_CACHE_VFATS 2 // Maximum number of 13-byte VFAT entries to use for sorting. + // Note: Only affects SCROLL_LONG_FILENAMES with SDSORT_CACHE_NAMES but not SDSORT_DYNAMIC_RAM. + #endif + + // This allows hosts to request long names for files and folders with M33 + //#define LONG_FILENAME_HOST_SUPPORT + + // Enable this option to scroll long filenames in the SD card menu + //#define SCROLL_LONG_FILENAMES + + // Leave the heaters on after Stop Print (not recommended!) + //#define SD_ABORT_NO_COOLDOWN + + /** + * This option allows you to abort SD printing when any endstop is triggered. + * This feature must be enabled with "M540 S1" or from the LCD menu. + * To have any effect, endstops must be enabled during SD printing. + */ + //#define SD_ABORT_ON_ENDSTOP_HIT + + /** + * This option makes it easier to print the same SD Card file again. + * On print completion the LCD Menu will open with the file selected. + * You can just click to start the print, or navigate elsewhere. + */ + //#define SD_REPRINT_LAST_SELECTED_FILE + + /** + * Auto-report SdCard status with M27 S + */ + //#define AUTO_REPORT_SD_STATUS + + /** + * Support for USB thumb drives using an Arduino USB Host Shield or + * equivalent MAX3421E breakout board. The USB thumb drive will appear + * to Marlin as an SD card. + * + * The MAX3421E can be assigned the same pins as the SD card reader, with + * the following pin mapping: + * + * SCLK, MOSI, MISO --> SCLK, MOSI, MISO + * INT --> SD_DETECT_PIN [1] + * SS --> SDSS + * + * [1] On AVR an interrupt-capable pin is best for UHS3 compatibility. + */ + //#define USB_FLASH_DRIVE_SUPPORT + #if ENABLED(USB_FLASH_DRIVE_SUPPORT) + #define USB_CS_PIN SDSS + #define USB_INTR_PIN SD_DETECT_PIN + + /** + * USB Host Shield Library + * + * - UHS2 uses no interrupts and has been production-tested + * on a LulzBot TAZ Pro with a 32-bit Archim board. + * + * - UHS3 is newer code with better USB compatibility. But it + * is less tested and is known to interfere with Servos. + * [1] This requires USB_INTR_PIN to be interrupt-capable. + */ + //#define USE_UHS3_USB + #endif + + /** + * When using a bootloader that supports SD-Firmware-Flashing, + * add a menu item to activate SD-FW-Update on the next reboot. + * + * Requires ATMEGA2560 (Arduino Mega) + * + * Tested with this bootloader: + * https://github.com/FleetProbe/MicroBridge-Arduino-ATMega2560 + */ + //#define SD_FIRMWARE_UPDATE + #if ENABLED(SD_FIRMWARE_UPDATE) + #define SD_FIRMWARE_UPDATE_EEPROM_ADDR 0x1FF + #define SD_FIRMWARE_UPDATE_ACTIVE_VALUE 0xF0 + #define SD_FIRMWARE_UPDATE_INACTIVE_VALUE 0xFF + #endif + + // Add an optimized binary file transfer mode, initiated with 'M28 B1' + //#define BINARY_FILE_TRANSFER + + #if HAS_SDCARD_CONNECTION + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD + #endif + +#endif // SDSUPPORT + +/** + * By default an onboard SD card reader may be shared as a USB mass- + * storage device. This option hides the SD card from the host PC. + */ +//#define NO_SD_HOST_DRIVE // Disable SD Card access over USB (for security). + +/** + * Additional options for Graphical Displays + * + * Use the optimizations here to improve printing performance, + * which can be adversely affected by graphical display drawing, + * especially when doing several short moves, and when printing + * on DELTA and SCARA machines. + * + * Some of these options may result in the display lagging behind + * controller events, as there is a trade-off between reliable + * printing performance versus fast display updates. + */ +#if HAS_GRAPHICAL_LCD + // Show SD percentage next to the progress bar + //#define DOGM_SD_PERCENT + + // Enable to save many cycles by drawing a hollow frame on the Info Screen + #define XYZ_HOLLOW_FRAME + + // Enable to save many cycles by drawing a hollow frame on Menu Screens + #define MENU_HOLLOW_FRAME + + // A bigger font is available for edit items. Costs 3120 bytes of PROGMEM. + // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese. + //#define USE_BIG_EDIT_FONT + + // A smaller font may be used on the Info Screen. Costs 2300 bytes of PROGMEM. + // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese. + //#define USE_SMALL_INFOFONT + + // Enable this option and reduce the value to optimize screen updates. + // The normal delay is 10µs. Use the lowest value that still gives a reliable display. + //#define DOGM_SPI_DELAY_US 5 + + // Swap the CW/CCW indicators in the graphics overlay + //#define OVERLAY_GFX_REVERSE + + /** + * ST7920-based LCDs can emulate a 16 x 4 character display using + * the ST7920 character-generator for very fast screen updates. + * Enable LIGHTWEIGHT_UI to use this special display mode. + * + * Since LIGHTWEIGHT_UI has limited space, the position and status + * message occupy the same line. Set STATUS_EXPIRE_SECONDS to the + * length of time to display the status message before clearing. + * + * Set STATUS_EXPIRE_SECONDS to zero to never clear the status. + * This will prevent position updates from being displayed. + */ + #if ENABLED(U8GLIB_ST7920) + //#define LIGHTWEIGHT_UI + #if ENABLED(LIGHTWEIGHT_UI) + #define STATUS_EXPIRE_SECONDS 20 + #endif + #endif + + /** + * Status (Info) Screen customizations + * These options may affect code size and screen render time. + * Custom status screens can forcibly override these settings. + */ + //#define STATUS_COMBINE_HEATERS // Use combined heater images instead of separate ones + //#define STATUS_HOTEND_NUMBERLESS // Use plain hotend icons instead of numbered ones (with 2+ hotends) + #define STATUS_HOTEND_INVERTED // Show solid nozzle bitmaps when heating (Requires STATUS_HOTEND_ANIM) + #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating + #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating + #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap + //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap + //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames + //#define STATUS_HEAT_PERCENT // Show heating in a progress bar + //#define BOOT_MARLIN_LOGO_SMALL // Show a smaller Marlin logo on the Boot Screen (saving 399 bytes of flash) + //#define BOOT_MARLIN_LOGO_ANIMATED // Animated Marlin logo. Costs ~‭3260 (or ~940) bytes of PROGMEM. + + // Frivolous Game Options + //#define MARLIN_BRICKOUT + //#define MARLIN_INVADERS + //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu + +#endif // HAS_GRAPHICAL_LCD + +// +// Lulzbot Touch UI +// +#if ENABLED(LULZBOT_TOUCH_UI) + // Display board used + //#define LCD_FTDI_VM800B35A // FTDI 3.5" with FT800 (320x240) + //#define LCD_4DSYSTEMS_4DLCD_FT843 // 4D Systems 4.3" (480x272) + //#define LCD_HAOYU_FT800CB // Haoyu with 4.3" or 5" (480x272) + //#define LCD_HAOYU_FT810CB // Haoyu with 5" (800x480) + //#define LCD_ALEPHOBJECTS_CLCD_UI // Aleph Objects Color LCD UI + + // Correct the resolution if not using the stock TFT panel. + //#define TOUCH_UI_320x240 + //#define TOUCH_UI_480x272 + //#define TOUCH_UI_800x480 + + // Mappings for boards with a standard RepRapDiscount Display connector + //#define AO_EXP1_PINMAP // AlephObjects CLCD UI EXP1 mapping + //#define AO_EXP2_PINMAP // AlephObjects CLCD UI EXP2 mapping + //#define CR10_TFT_PINMAP // Rudolph Riedel's CR10 pin mapping + //#define OTHER_PIN_LAYOUT // Define pins manually below + #if ENABLED(OTHER_PIN_LAYOUT) + // The pins for CS and MOD_RESET (PD) must be chosen. + #define CLCD_MOD_RESET 9 + #define CLCD_SPI_CS 10 + + // If using software SPI, specify pins for SCLK, MOSI, MISO + //#define CLCD_USE_SOFT_SPI + #if ENABLED(CLCD_USE_SOFT_SPI) + #define CLCD_SOFT_SPI_MOSI 11 + #define CLCD_SOFT_SPI_MISO 12 + #define CLCD_SOFT_SPI_SCLK 13 + #endif + #endif + + // Display Orientation. An inverted (i.e. upside-down) display + // is supported on the FT800. The FT810 and beyond also support + // portrait and mirrored orientations. + //#define TOUCH_UI_INVERTED + //#define TOUCH_UI_PORTRAIT + //#define TOUCH_UI_MIRRORED + + // UTF8 processing and rendering. + // Unsupported characters are shown as '?'. + //#define TOUCH_UI_USE_UTF8 + #if ENABLED(TOUCH_UI_USE_UTF8) + // Western accents support. These accented characters use + // combined bitmaps and require relatively little storage. + #define TOUCH_UI_UTF8_WESTERN_CHARSET + #if ENABLED(TOUCH_UI_UTF8_WESTERN_CHARSET) + // Additional character groups. These characters require + // full bitmaps and take up considerable storage: + //#define TOUCH_UI_UTF8_SUPERSCRIPTS // ¹ ² ³ + //#define TOUCH_UI_UTF8_COPYRIGHT // © ® + //#define TOUCH_UI_UTF8_GERMANIC // ß + //#define TOUCH_UI_UTF8_SCANDINAVIAN // Æ Ð Ø Þ æ ð ø þ + //#define TOUCH_UI_UTF8_PUNCTUATION // « » ¿ ¡ + //#define TOUCH_UI_UTF8_CURRENCY // ¢ £ ¤ ¥ + //#define TOUCH_UI_UTF8_ORDINALS // º ª + //#define TOUCH_UI_UTF8_MATHEMATICS // ± × ÷ + //#define TOUCH_UI_UTF8_FRACTIONS // ¼ ½ ¾ + //#define TOUCH_UI_UTF8_SYMBOLS // µ ¶ ¦ § ¬ + #endif + #endif + + // Use a smaller font when labels don't fit buttons + #define TOUCH_UI_FIT_TEXT + + // Allow language selection from menu at run-time (otherwise use LCD_LANGUAGE) + //#define LCD_LANGUAGE_1 en + //#define LCD_LANGUAGE_2 fr + //#define LCD_LANGUAGE_3 de + //#define LCD_LANGUAGE_4 es + //#define LCD_LANGUAGE_5 it + + // Use a numeric passcode for "Screen lock" keypad. + // (recommended for smaller displays) + //#define TOUCH_UI_PASSCODE + + // Output extra debug info for Touch UI events + //#define TOUCH_UI_DEBUG +#endif + +// +// FSMC Graphical TFT +// +#if ENABLED(FSMC_GRAPHICAL_TFT) + //#define TFT_MARLINUI_COLOR 0xFFFF // White + //#define TFT_MARLINBG_COLOR 0x0000 // Black + //#define TFT_DISABLED_COLOR 0x0003 // Almost black + //#define TFT_BTCANCEL_COLOR 0xF800 // Red + //#define TFT_BTARROWS_COLOR 0xDEE6 // 11011 110111 00110 Yellow + //#define TFT_BTOKMENU_COLOR 0x145F // 00010 100010 11111 Cyan +#endif + +// @section safety + +/** + * The watchdog hardware timer will do a reset and disable all outputs + * if the firmware gets too overloaded to read the temperature sensors. + * + * If you find that watchdog reboot causes your AVR board to hang forever, + * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO. + * NOTE: This method is less reliable as it can only catch hangups while + * interrupts are enabled. + */ +#define USE_WATCHDOG +#if ENABLED(USE_WATCHDOG) + //#define WATCHDOG_RESET_MANUAL +#endif + +// @section lcd + +/** + * Babystepping enables movement of the axes by tiny increments without changing + * the current position values. This feature is used primarily to adjust the Z + * axis in the first layer of a print in real-time. + * + * Warning: Does not respect endstops! + */ +//#define BABYSTEPPING +#if ENABLED(BABYSTEPPING) + //#define BABYSTEP_WITHOUT_HOMING + //#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA! + #define BABYSTEP_INVERT_Z false // Change if Z babysteps should go the other way + #define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion. + + //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping. + #if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING) + #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds. + // Note: Extra time may be added to mitigate controller latency. + //#define BABYSTEP_ALWAYS_AVAILABLE // Allow babystepping at all times (not just during movement). + //#define MOVE_Z_WHEN_IDLE // Jump to the move Z menu on doubleclick when printer is idle. + #if ENABLED(MOVE_Z_WHEN_IDLE) + #define MOVE_Z_IDLE_MULTIPLICATOR 1 // Multiply 1mm by this factor for the move step size. + #endif + #endif + + //#define BABYSTEP_DISPLAY_TOTAL // Display total babysteps since last G28 + + //#define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping + #if ENABLED(BABYSTEP_ZPROBE_OFFSET) + //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets + //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor + #endif +#endif + +// @section extruder + +/** + * Linear Pressure Control v1.5 + * + * Assumption: advance [steps] = k * (delta velocity [steps/s]) + * K=0 means advance disabled. + * + * NOTE: K values for LIN_ADVANCE 1.5 differ from earlier versions! + * + * Set K around 0.22 for 3mm PLA Direct Drive with ~6.5cm between the drive gear and heatbreak. + * Larger K values will be needed for flexible filament and greater distances. + * If this algorithm produces a higher speed offset than the extruder can handle (compared to E jerk) + * print acceleration will be reduced during the affected moves to keep within the limit. + * + * See http://marlinfw.org/docs/features/lin_advance.html for full instructions. + * Mention @Sebastianv650 on GitHub to alert the author of any issues. + */ +//#define LIN_ADVANCE +#if ENABLED(LIN_ADVANCE) + //#define EXTRA_LIN_ADVANCE_K // Enable for second linear advance constants + #define LIN_ADVANCE_K 0.22 // Unit: mm compression per 1mm/s extruder speed + //#define LA_DEBUG // If enabled, this will generate debug information output over USB. +#endif + +// @section leveling + +/** + * Points to probe for all 3-point Leveling procedures. + * Override if the automatically selected points are inadequate. + */ +#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL) + //#define PROBE_PT_1_X 15 + //#define PROBE_PT_1_Y 180 + //#define PROBE_PT_2_X 15 + //#define PROBE_PT_2_Y 20 + //#define PROBE_PT_3_X 170 + //#define PROBE_PT_3_Y 20 +#endif + +/** + * Override MIN_PROBE_EDGE for each side of the build plate + * Useful to get probe points to exact positions on targets or + * to allow leveling to avoid plate clamps on only specific + * sides of the bed. + * + * If you are replacing the prior *_PROBE_BED_POSITION options, + * LEFT and FRONT values in most cases will map directly over + * RIGHT and REAR would be the inverse such as + * (X/Y_BED_SIZE - RIGHT/BACK_PROBE_BED_POSITION) + * + * This will allow all positions to match at compilation, however + * should the probe position be modified with M851XY then the + * probe points will follow. This prevents any change from causing + * the probe to be unable to reach any points. + */ +#if PROBE_SELECTED && !IS_KINEMATIC + //#define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE + //#define MIN_PROBE_EDGE_RIGHT MIN_PROBE_EDGE + //#define MIN_PROBE_EDGE_FRONT MIN_PROBE_EDGE + //#define MIN_PROBE_EDGE_BACK MIN_PROBE_EDGE +#endif + +#if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL) + // Override the mesh area if the automatic (max) area is too large + //#define MESH_MIN_X MESH_INSET + //#define MESH_MIN_Y MESH_INSET + //#define MESH_MAX_X X_BED_SIZE - (MESH_INSET) + //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET) +#endif + +/** + * Repeatedly attempt G29 leveling until it succeeds. + * Stop after G29_MAX_RETRIES attempts. + */ +//#define G29_RETRY_AND_RECOVER +#if ENABLED(G29_RETRY_AND_RECOVER) + #define G29_MAX_RETRIES 3 + #define G29_HALT_ON_FAILURE + /** + * Specify the GCODE commands that will be executed when leveling succeeds, + * between attempts, and after the maximum number of retries have been tried. + */ + #define G29_SUCCESS_COMMANDS "M117 Bed leveling done." + #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0" + #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1" + +#endif + +// @section extras + +// +// G2/G3 Arc Support +// +#define ARC_SUPPORT // Disable this feature to save ~3226 bytes +#if ENABLED(ARC_SUPPORT) + #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles + //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes +#endif + +// Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes. +//#define BEZIER_CURVE_SUPPORT + +/** + * G38 Probe Target + * + * This option adds G38.2 and G38.3 (probe towards target) + * and optionally G38.4 and G38.5 (probe away from target). + * Set MULTIPLE_PROBING for G38 to probe more than once. + */ +//#define G38_PROBE_TARGET +#if ENABLED(G38_PROBE_TARGET) + //#define G38_PROBE_AWAY // Include G38.4 and G38.5 to probe away from target + #define G38_MINIMUM_MOVE 0.0275 // (mm) Minimum distance that will produce a move. +#endif + +// Moves (or segments) with fewer steps than this will be joined with the next move +#define MIN_STEPS_PER_SEGMENT 6 + +/** + * Minimum delay before and after setting the stepper DIR (in ns) + * 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire) + * 20 : Minimum for TMC2xxx drivers + * 200 : Minimum for A4988 drivers + * 400 : Minimum for A5984 drivers + * 500 : Minimum for LV8729 drivers (guess, no info in datasheet) + * 650 : Minimum for DRV8825 drivers + * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet) + * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet) + * + * Override the default value based on the driver type set in Configuration.h. + */ +//#define MINIMUM_STEPPER_POST_DIR_DELAY 650 +//#define MINIMUM_STEPPER_PRE_DIR_DELAY 650 + +/** + * Minimum stepper driver pulse width (in µs) + * 0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers + * 0 : Minimum 500ns for LV8729, adjusted in stepper.h + * 1 : Minimum for A4988 and A5984 stepper drivers + * 2 : Minimum for DRV8825 stepper drivers + * 3 : Minimum for TB6600 stepper drivers + * 30 : Minimum for TB6560 stepper drivers + * + * Override the default value based on the driver type set in Configuration.h. + */ +//#define MINIMUM_STEPPER_PULSE 2 + +/** + * Maximum stepping rate (in Hz) the stepper driver allows + * If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE) + * 500000 : Maximum for A4988 stepper driver + * 400000 : Maximum for TMC2xxx stepper drivers + * 250000 : Maximum for DRV8825 stepper driver + * 200000 : Maximum for LV8729 stepper driver + * 150000 : Maximum for TB6600 stepper driver + * 15000 : Maximum for TB6560 stepper driver + * + * Override the default value based on the driver type set in Configuration.h. + */ +//#define MAXIMUM_STEPPER_RATE 250000 + +// @section temperature + +// Control heater 0 and heater 1 in parallel. +//#define HEATERS_PARALLEL + +//=========================================================================== +//================================= Buffers ================================= +//=========================================================================== + +// @section hidden + +// The number of linear motions that can be in the plan at any give time. +// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2 (e.g. 8, 16, 32) because shifts and ors are used to do the ring-buffering. +#if ENABLED(SDSUPPORT) + #define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller +#else + #define BLOCK_BUFFER_SIZE 16 // maximize block buffer +#endif + +// @section serial + +// The ASCII buffer for serial input +#define MAX_CMD_SIZE 96 +#define BUFSIZE 26 + +// Transmission to Host Buffer Size +// To save 386 bytes of PROGMEM (and TX_BUFFER_SIZE+3 bytes of RAM) set to 0. +// To buffer a simple "ok" you need 4 bytes. +// For ADVANCED_OK (M105) you need 32 bytes. +// For debug-echo: 128 bytes for the optimal speed. +// Other output doesn't need to be that speedy. +// :[0, 2, 4, 8, 16, 32, 64, 128, 256] +#define TX_BUFFER_SIZE 0 + +// Host Receive Buffer Size +// Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough. +// To use flow control, set this buffer size to at least 1024 bytes. +// :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048] +//#define RX_BUFFER_SIZE 1024 + +#if RX_BUFFER_SIZE >= 1024 + // Enable to have the controller send XON/XOFF control characters to + // the host to signal the RX buffer is becoming full. + //#define SERIAL_XON_XOFF +#endif + +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + +#if ENABLED(SDSUPPORT) + // Enable this option to collect and display the maximum + // RX queue usage after transferring a file to SD. + //#define SERIAL_STATS_MAX_RX_QUEUED + + // Enable this option to collect and display the number + // of dropped bytes after a file transfer to SD. + //#define SERIAL_STATS_DROPPED_RX +#endif + +// Enable an emergency-command parser to intercept certain commands as they +// enter the serial receive buffer, so they cannot be blocked. +// Currently handles M108, M112, M410 +// Does not work on boards using AT90USB (USBCON) processors! +//#define EMERGENCY_PARSER + +// Bad Serial-connections can miss a received command by sending an 'ok' +// Therefore some clients abort after 30 seconds in a timeout. +// Some other clients start sending commands while receiving a 'wait'. +// This "wait" is only sent when the buffer is empty. 1 second is a good value here. +//#define NO_TIMEOUTS 1000 // Milliseconds + +// Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary. +//#define ADVANCED_OK + +// Printrun may have trouble receiving long strings all at once. +// This option inserts short delays between lines of serial output. +#define SERIAL_OVERRUN_PROTECTION + +// @section extras + +/** + * Extra Fan Speed + * Adds a secondary fan speed for each print-cooling fan. + * 'M106 P T3-255' : Set a secondary speed for + * 'M106 P T2' : Use the set secondary speed + * 'M106 P T1' : Restore the previous fan speed + */ +//#define EXTRA_FAN_SPEED + +/** + * Firmware-based and LCD-controlled retract + * + * Add G10 / G11 commands for automatic firmware-based retract / recover. + * Use M207 and M208 to define parameters for retract / recover. + * + * Use M209 to enable or disable auto-retract. + * With auto-retract enabled, all G1 E moves within the set range + * will be converted to firmware-based retract/recover moves. + * + * Be sure to turn off auto-retract during filament change. + * + * Note that M207 / M208 / M209 settings are saved to EEPROM. + * + */ +//#define FWRETRACT +#if ENABLED(FWRETRACT) + #define FWRETRACT_AUTORETRACT // Override slicer retractions + #if ENABLED(FWRETRACT_AUTORETRACT) + #define MIN_AUTORETRACT 0.1 // (mm) Don't convert E moves under this length + #define MAX_AUTORETRACT 10.0 // (mm) Don't convert E moves over this length + #endif + #define RETRACT_LENGTH 3 // (mm) Default retract length (positive value) + #define RETRACT_LENGTH_SWAP 13 // (mm) Default swap retract length (positive value) + #define RETRACT_FEEDRATE 45 // (mm/s) Default feedrate for retracting + #define RETRACT_ZRAISE 0 // (mm) Default retract Z-raise + #define RETRACT_RECOVER_LENGTH 0 // (mm) Default additional recover length (added to retract length on recover) + #define RETRACT_RECOVER_LENGTH_SWAP 0 // (mm) Default additional swap recover length (added to retract length on recover from toolchange) + #define RETRACT_RECOVER_FEEDRATE 8 // (mm/s) Default feedrate for recovering from retraction + #define RETRACT_RECOVER_FEEDRATE_SWAP 8 // (mm/s) Default feedrate for recovering from swap retraction + #if ENABLED(MIXING_EXTRUDER) + //#define RETRACT_SYNC_MIXING // Retract and restore all mixing steppers simultaneously + #endif +#endif + +/** + * Universal tool change settings. + * Applies to all types of extruders except where explicitly noted. + */ +#if EXTRUDERS > 1 + // Z raise distance for tool-change, as needed for some extruders + #define TOOLCHANGE_ZRAISE 2 // (mm) + //#define TOOLCHANGE_NO_RETURN // Never return to the previous position on tool-change + + // Retract and prime filament on tool-change + //#define TOOLCHANGE_FILAMENT_SWAP + #if ENABLED(TOOLCHANGE_FILAMENT_SWAP) + #define TOOLCHANGE_FIL_SWAP_LENGTH 12 // (mm) + #define TOOLCHANGE_FIL_EXTRA_PRIME 2 // (mm) + #define TOOLCHANGE_FIL_SWAP_RETRACT_SPEED 3600 // (mm/m) + #define TOOLCHANGE_FIL_SWAP_PRIME_SPEED 3600 // (mm/m) + #endif + + /** + * Position to park head during tool change. + * Doesn't apply to SWITCHING_TOOLHEAD, DUAL_X_CARRIAGE, or PARKING_EXTRUDER + */ + //#define TOOLCHANGE_PARK + #if ENABLED(TOOLCHANGE_PARK) + #define TOOLCHANGE_PARK_XY { X_MIN_POS + 10, Y_MIN_POS + 10 } + #define TOOLCHANGE_PARK_XY_FEEDRATE 6000 // (mm/m) + #endif +#endif + +/** + * Advanced Pause + * Experimental feature for filament change support and for parking the nozzle when paused. + * Adds the GCode M600 for initiating filament change. + * If PARK_HEAD_ON_PAUSE enabled, adds the GCode M125 to pause printing and park the nozzle. + * + * Requires an LCD display. + * Requires NOZZLE_PARK_FEATURE. + * This feature is required for the default FILAMENT_RUNOUT_SCRIPT. + */ +//#define ADVANCED_PAUSE_FEATURE +#if ENABLED(ADVANCED_PAUSE_FEATURE) + #define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate. + #define PAUSE_PARK_RETRACT_LENGTH 5 // (mm) Initial retract. + // This short retract is done immediately, before parking the nozzle. + #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast. + #define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate. + #define FILAMENT_CHANGE_UNLOAD_LENGTH 600 // (mm) The length of filament for a complete unload. + // For Bowden, the full length of the tube and nozzle. + // For direct drive, the full length of the nozzle. + // Set to 0 for manual unloading. + #define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load. + #define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material. + // 0 to disable start loading and skip to fast load only + #define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast. + #define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate. + #define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle. + // For Bowden, the full length of the tube and nozzle. + // For direct drive, the full length of the nozzle. + //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted. + #define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate. + #define ADVANCED_PAUSE_PURGE_LENGTH 100 // (mm) Length to extrude after loading. + // Set to 0 for manual extrusion. + // Filament can be extruded repeatedly from the Filament Change menu + // until extrusion is consistent, and to purge old filament. + #define ADVANCED_PAUSE_RESUME_PRIME 0 // (mm) Extra distance to prime nozzle after returning from park. + //#define ADVANCED_PAUSE_FANS_PAUSE // Turn off print-cooling fans while the machine is paused. + + // Filament Unload does a Retract, Delay, and Purge first: + #define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length. + #define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract. + #define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged. + + #define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety. + #define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed. + #define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change. + + //#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change. + //#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change + + //#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu. + //#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302) +#endif + +// @section tmc + +/** + * TMC26X Stepper Driver options + * + * The TMC26XStepper library is required for this stepper driver. + * https://github.com/trinamic/TMC26XStepper + */ +#if HAS_DRIVER(TMC26X) + + #if AXIS_DRIVER_TYPE_X(TMC26X) + #define X_MAX_CURRENT 1000 // (mA) + #define X_SENSE_RESISTOR 91 // (mOhms) + #define X_MICROSTEPS 16 // Number of microsteps + #endif + + #if AXIS_DRIVER_TYPE_X2(TMC26X) + #define X2_MAX_CURRENT 1000 + #define X2_SENSE_RESISTOR 91 + #define X2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Y(TMC26X) + #define Y_MAX_CURRENT 1000 + #define Y_SENSE_RESISTOR 91 + #define Y_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Y2(TMC26X) + #define Y2_MAX_CURRENT 1000 + #define Y2_SENSE_RESISTOR 91 + #define Y2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Z(TMC26X) + #define Z_MAX_CURRENT 1000 + #define Z_SENSE_RESISTOR 91 + #define Z_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Z2(TMC26X) + #define Z2_MAX_CURRENT 1000 + #define Z2_SENSE_RESISTOR 91 + #define Z2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Z3(TMC26X) + #define Z3_MAX_CURRENT 1000 + #define Z3_SENSE_RESISTOR 91 + #define Z3_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E0(TMC26X) + #define E0_MAX_CURRENT 1000 + #define E0_SENSE_RESISTOR 91 + #define E0_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E1(TMC26X) + #define E1_MAX_CURRENT 1000 + #define E1_SENSE_RESISTOR 91 + #define E1_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E2(TMC26X) + #define E2_MAX_CURRENT 1000 + #define E2_SENSE_RESISTOR 91 + #define E2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E3(TMC26X) + #define E3_MAX_CURRENT 1000 + #define E3_SENSE_RESISTOR 91 + #define E3_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E4(TMC26X) + #define E4_MAX_CURRENT 1000 + #define E4_SENSE_RESISTOR 91 + #define E4_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E5(TMC26X) + #define E5_MAX_CURRENT 1000 + #define E5_SENSE_RESISTOR 91 + #define E5_MICROSTEPS 16 + #endif + +#endif // TMC26X + +// @section tmc_smart + +/** + * To use TMC2130, TMC2160, TMC2660, TMC5130, TMC5160 stepper drivers in SPI mode + * connect your SPI pins to the hardware SPI interface on your board and define + * the required CS pins in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 + * pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.). + * You may also use software SPI if you wish to use general purpose IO pins. + * + * To use TMC2208 stepper UART-configurable stepper drivers connect #_SERIAL_TX_PIN + * to the driver side PDN_UART pin with a 1K resistor. + * To use the reading capabilities, also connect #_SERIAL_RX_PIN to PDN_UART without + * a resistor. + * The drivers can also be used with hardware serial. + * + * TMCStepper library is required to use TMC stepper drivers. + * https://github.com/teemuatlut/TMCStepper + */ +#if HAS_TRINAMIC + + #define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current + #define INTERPOLATE true // Interpolate X/Y/Z_MICROSTEPS to 256 + + #if AXIS_IS_TMC(X) + #define X_CURRENT 800 // (mA) RMS current. Multiply by 1.414 for peak current. + #define X_MICROSTEPS 16 // 0..256 + #define X_RSENSE 0.11 + #define X_CHAIN_POS -1 // <=0 : Not chained. 1 : MCU MOSI connected. 2 : Next in chain, ... + #endif + + #if AXIS_IS_TMC(X2) + #define X2_CURRENT 800 + #define X2_MICROSTEPS 16 + #define X2_RSENSE 0.11 + #define X2_CHAIN_POS -1 + #endif + + #if AXIS_IS_TMC(Y) + #define Y_CURRENT 800 + #define Y_MICROSTEPS 16 + #define Y_RSENSE 0.11 + #define Y_CHAIN_POS -1 + #endif + + #if AXIS_IS_TMC(Y2) + #define Y2_CURRENT 800 + #define Y2_MICROSTEPS 16 + #define Y2_RSENSE 0.11 + #define Y2_CHAIN_POS -1 + #endif + + #if AXIS_IS_TMC(Z) + #define Z_CURRENT 800 + #define Z_MICROSTEPS 16 + #define Z_RSENSE 0.11 + #define Z_CHAIN_POS -1 + #endif + + #if AXIS_IS_TMC(Z2) + #define Z2_CURRENT 800 + #define Z2_MICROSTEPS 16 + #define Z2_RSENSE 0.11 + #define Z2_CHAIN_POS -1 + #endif + + #if AXIS_IS_TMC(Z3) + #define Z3_CURRENT 800 + #define Z3_MICROSTEPS 16 + #define Z3_RSENSE 0.11 + #define Z3_CHAIN_POS -1 + #endif + + #if AXIS_IS_TMC(E0) + #define E0_CURRENT 800 + #define E0_MICROSTEPS 16 + #define E0_RSENSE 0.11 + #define E0_CHAIN_POS -1 + #endif + + #if AXIS_IS_TMC(E1) + #define E1_CURRENT 800 + #define E1_MICROSTEPS 16 + #define E1_RSENSE 0.11 + #define E1_CHAIN_POS -1 + #endif + + #if AXIS_IS_TMC(E2) + #define E2_CURRENT 800 + #define E2_MICROSTEPS 16 + #define E2_RSENSE 0.11 + #define E2_CHAIN_POS -1 + #endif + + #if AXIS_IS_TMC(E3) + #define E3_CURRENT 800 + #define E3_MICROSTEPS 16 + #define E3_RSENSE 0.11 + #define E3_CHAIN_POS -1 + #endif + + #if AXIS_IS_TMC(E4) + #define E4_CURRENT 800 + #define E4_MICROSTEPS 16 + #define E4_RSENSE 0.11 + #define E4_CHAIN_POS -1 + #endif + + #if AXIS_IS_TMC(E5) + #define E5_CURRENT 800 + #define E5_MICROSTEPS 16 + #define E5_RSENSE 0.11 + #define E5_CHAIN_POS -1 + #endif + + /** + * Override default SPI pins for TMC2130, TMC2160, TMC2660, TMC5130 and TMC5160 drivers here. + * The default pins can be found in your board's pins file. + */ + //#define X_CS_PIN -1 + //#define Y_CS_PIN -1 + //#define Z_CS_PIN -1 + //#define X2_CS_PIN -1 + //#define Y2_CS_PIN -1 + //#define Z2_CS_PIN -1 + //#define Z3_CS_PIN -1 + //#define E0_CS_PIN -1 + //#define E1_CS_PIN -1 + //#define E2_CS_PIN -1 + //#define E3_CS_PIN -1 + //#define E4_CS_PIN -1 + //#define E5_CS_PIN -1 + + /** + * Software option for SPI driven drivers (TMC2130, TMC2160, TMC2660, TMC5130 and TMC5160). + * The default SW SPI pins are defined the respective pins files, + * but you can override or define them here. + */ + //#define TMC_USE_SW_SPI + //#define TMC_SW_MOSI -1 + //#define TMC_SW_MISO -1 + //#define TMC_SW_SCK -1 + + /** + * Four TMC2209 drivers can use the same HW/SW serial port with hardware configured addresses. + * Set the address using jumpers on pins MS1 and MS2. + * Address | MS1 | MS2 + * 0 | LOW | LOW + * 1 | HIGH | LOW + * 2 | LOW | HIGH + * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. + */ + #define X_SLAVE_ADDRESS 0 + #define Y_SLAVE_ADDRESS 0 + #define Z_SLAVE_ADDRESS 0 + #define X2_SLAVE_ADDRESS 0 + #define Y2_SLAVE_ADDRESS 0 + #define Z2_SLAVE_ADDRESS 0 + #define Z3_SLAVE_ADDRESS 0 + #define E0_SLAVE_ADDRESS 0 + #define E1_SLAVE_ADDRESS 0 + #define E2_SLAVE_ADDRESS 0 + #define E3_SLAVE_ADDRESS 0 + #define E4_SLAVE_ADDRESS 0 + #define E5_SLAVE_ADDRESS 0 + + /** + * Software enable + * + * Use for drivers that do not use a dedicated enable pin, but rather handle the same + * function through a communication line such as SPI or UART. + */ + //#define SOFTWARE_DRIVER_ENABLE + + /** + * TMC2130, TMC2160, TMC2208, TMC2209, TMC5130 and TMC5160 only + * Use Trinamic's ultra quiet stepping mode. + * When disabled, Marlin will use spreadCycle stepping mode. + */ + #define STEALTHCHOP_XY + #define STEALTHCHOP_Z + #define STEALTHCHOP_E + + /** + * Optimize spreadCycle chopper parameters by using predefined parameter sets + * or with the help of an example included in the library. + * Provided parameter sets are + * CHOPPER_DEFAULT_12V + * CHOPPER_DEFAULT_19V + * CHOPPER_DEFAULT_24V + * CHOPPER_DEFAULT_36V + * CHOPPER_PRUSAMK3_24V // Imported parameters from the official Prusa firmware for MK3 (24V) + * CHOPPER_MARLIN_119 // Old defaults from Marlin v1.1.9 + * + * Define you own with + * { , , hysteresis_start[1..8] } + */ + #define CHOPPER_TIMING CHOPPER_DEFAULT_12V + + /** + * Monitor Trinamic drivers for error conditions, + * like overtemperature and short to ground. + * In the case of overtemperature Marlin can decrease the driver current until error condition clears. + * Other detected conditions can be used to stop the current print. + * Relevant g-codes: + * M906 - Set or get motor current in milliamps using axis codes X, Y, Z, E. Report values if no axis codes given. + * M911 - Report stepper driver overtemperature pre-warn condition. + * M912 - Clear stepper driver overtemperature pre-warn condition flag. + * M122 - Report driver parameters (Requires TMC_DEBUG) + */ + //#define MONITOR_DRIVER_STATUS + + #if ENABLED(MONITOR_DRIVER_STATUS) + #define CURRENT_STEP_DOWN 50 // [mA] + #define REPORT_CURRENT_CHANGE + #define STOP_ON_ERROR + #endif + + /** + * TMC2130, TMC2160, TMC2208, TMC2209, TMC5130 and TMC5160 only + * The driver will switch to spreadCycle when stepper speed is over HYBRID_THRESHOLD. + * This mode allows for faster movements at the expense of higher noise levels. + * STEALTHCHOP_(XY|Z|E) must be enabled to use HYBRID_THRESHOLD. + * M913 X/Y/Z/E to live tune the setting + */ + //#define HYBRID_THRESHOLD + + #define X_HYBRID_THRESHOLD 100 // [mm/s] + #define X2_HYBRID_THRESHOLD 100 + #define Y_HYBRID_THRESHOLD 100 + #define Y2_HYBRID_THRESHOLD 100 + #define Z_HYBRID_THRESHOLD 3 + #define Z2_HYBRID_THRESHOLD 3 + #define Z3_HYBRID_THRESHOLD 3 + #define E0_HYBRID_THRESHOLD 30 + #define E1_HYBRID_THRESHOLD 30 + #define E2_HYBRID_THRESHOLD 30 + #define E3_HYBRID_THRESHOLD 30 + #define E4_HYBRID_THRESHOLD 30 + #define E5_HYBRID_THRESHOLD 30 + + /** + * Use StallGuard2 to home / probe X, Y, Z. + * + * TMC2130, TMC2160, TMC2209, TMC2660, TMC5130, and TMC5160 only + * Connect the stepper driver's DIAG1 pin to the X/Y endstop pin. + * X, Y, and Z homing will always be done in spreadCycle mode. + * + * X/Y/Z_STALL_SENSITIVITY is the default stall threshold. + * Use M914 X Y Z to set the stall threshold at runtime: + * + * Sensitivity TMC2209 Others + * HIGHEST 255 -64 (Too sensitive => False positive) + * LOWEST 0 63 (Too insensitive => No trigger) + * + * It is recommended to set [XYZ]_HOME_BUMP_MM to 0. + * + * SPI_ENDSTOPS *** Beta feature! *** TMC2130 Only *** + * Poll the driver through SPI to determine load when homing. + * Removes the need for a wire from DIAG1 to an endstop pin. + * + * IMPROVE_HOMING_RELIABILITY tunes acceleration and jerk when + * homing and adds a guard period for endstop triggering. + */ + //#define SENSORLESS_HOMING // StallGuard capable drivers only + + /** + * Use StallGuard2 to probe the bed with the nozzle. + * + * CAUTION: This could cause damage to machines that use a lead screw or threaded rod + * to move the Z axis. Take extreme care when attempting to enable this feature. + */ + //#define SENSORLESS_PROBING // StallGuard capable drivers only + + #if EITHER(SENSORLESS_HOMING, SENSORLESS_PROBING) + // TMC2209: 0...255. TMC2130: -64...63 + #define X_STALL_SENSITIVITY 8 + #define X2_STALL_SENSITIVITY X_STALL_SENSITIVITY + #define Y_STALL_SENSITIVITY 8 + //#define Z_STALL_SENSITIVITY 8 + //#define SPI_ENDSTOPS // TMC2130 only + //#define IMPROVE_HOMING_RELIABILITY + #endif + + /** + * Beta feature! + * Create a 50/50 square wave step pulse optimal for stepper drivers. + */ + //#define SQUARE_WAVE_STEPPING + + /** + * Enable M122 debugging command for TMC stepper drivers. + * M122 S0/1 will enable continous reporting. + */ + //#define TMC_DEBUG + + /** + * You can set your own advanced settings by filling in predefined functions. + * A list of available functions can be found on the library github page + * https://github.com/teemuatlut/TMCStepper + * + * Example: + * #define TMC_ADV() { \ + * stepperX.diag0_temp_prewarn(1); \ + * stepperY.interpolate(0); \ + * } + */ + #define TMC_ADV() { } + +#endif // HAS_TRINAMIC + +// @section L6470 + +/** + * L6470 Stepper Driver options + * + * Arduino-L6470 library (0.7.0 or higher) is required for this stepper driver. + * https://github.com/ameyer/Arduino-L6470 + * + * Requires the following to be defined in your pins_YOUR_BOARD file + * L6470_CHAIN_SCK_PIN + * L6470_CHAIN_MISO_PIN + * L6470_CHAIN_MOSI_PIN + * L6470_CHAIN_SS_PIN + * L6470_RESET_CHAIN_PIN (optional) + */ +#if HAS_DRIVER(L6470) + + //#define L6470_CHITCHAT // Display additional status info + + #if AXIS_DRIVER_TYPE_X(L6470) + #define X_MICROSTEPS 128 // Number of microsteps (VALID: 1, 2, 4, 8, 16, 32, 128) + #define X_OVERCURRENT 2000 // (mA) Current where the driver detects an over current (VALID: 375 x (1 - 16) - 6A max - rounds down) + #define X_STALLCURRENT 1500 // (mA) Current where the driver detects a stall (VALID: 31.25 * (1-128) - 4A max - rounds down) + #define X_MAX_VOLTAGE 127 // 0-255, Maximum effective voltage seen by stepper + #define X_CHAIN_POS -1 // Position in SPI chain. (<=0 : Not in chain. 1 : Nearest MOSI) + #endif + + #if AXIS_DRIVER_TYPE_X2(L6470) + #define X2_MICROSTEPS 128 + #define X2_OVERCURRENT 2000 + #define X2_STALLCURRENT 1500 + #define X2_MAX_VOLTAGE 127 + #define X2_CHAIN_POS -1 + #endif + + #if AXIS_DRIVER_TYPE_Y(L6470) + #define Y_MICROSTEPS 128 + #define Y_OVERCURRENT 2000 + #define Y_STALLCURRENT 1500 + #define Y_MAX_VOLTAGE 127 + #define Y_CHAIN_POS -1 + #endif + + #if AXIS_DRIVER_TYPE_Y2(L6470) + #define Y2_MICROSTEPS 128 + #define Y2_OVERCURRENT 2000 + #define Y2_STALLCURRENT 1500 + #define Y2_MAX_VOLTAGE 127 + #define Y2_CHAIN_POS -1 + #endif + + #if AXIS_DRIVER_TYPE_Z(L6470) + #define Z_MICROSTEPS 128 + #define Z_OVERCURRENT 2000 + #define Z_STALLCURRENT 1500 + #define Z_MAX_VOLTAGE 127 + #define Z_CHAIN_POS -1 + #endif + + #if AXIS_DRIVER_TYPE_Z2(L6470) + #define Z2_MICROSTEPS 128 + #define Z2_OVERCURRENT 2000 + #define Z2_STALLCURRENT 1500 + #define Z2_MAX_VOLTAGE 127 + #define Z2_CHAIN_POS -1 + #endif + + #if AXIS_DRIVER_TYPE_Z3(L6470) + #define Z3_MICROSTEPS 128 + #define Z3_OVERCURRENT 2000 + #define Z3_STALLCURRENT 1500 + #define Z3_MAX_VOLTAGE 127 + #define Z3_CHAIN_POS -1 + #endif + + #if AXIS_DRIVER_TYPE_E0(L6470) + #define E0_MICROSTEPS 128 + #define E0_OVERCURRENT 2000 + #define E0_STALLCURRENT 1500 + #define E0_MAX_VOLTAGE 127 + #define E0_CHAIN_POS -1 + #endif + + #if AXIS_DRIVER_TYPE_E1(L6470) + #define E1_MICROSTEPS 128 + #define E1_OVERCURRENT 2000 + #define E1_STALLCURRENT 1500 + #define E1_MAX_VOLTAGE 127 + #define E1_CHAIN_POS -1 + #endif + + #if AXIS_DRIVER_TYPE_E2(L6470) + #define E2_MICROSTEPS 128 + #define E2_OVERCURRENT 2000 + #define E2_STALLCURRENT 1500 + #define E2_MAX_VOLTAGE 127 + #define E2_CHAIN_POS -1 + #endif + + #if AXIS_DRIVER_TYPE_E3(L6470) + #define E3_MICROSTEPS 128 + #define E3_OVERCURRENT 2000 + #define E3_STALLCURRENT 1500 + #define E3_MAX_VOLTAGE 127 + #define E3_CHAIN_POS -1 + #endif + + #if AXIS_DRIVER_TYPE_E4(L6470) + #define E4_MICROSTEPS 128 + #define E4_OVERCURRENT 2000 + #define E4_STALLCURRENT 1500 + #define E4_MAX_VOLTAGE 127 + #define E4_CHAIN_POS -1 + #endif + + #if AXIS_DRIVER_TYPE_E5(L6470) + #define E5_MICROSTEPS 128 + #define E5_OVERCURRENT 2000 + #define E5_STALLCURRENT 1500 + #define E5_MAX_VOLTAGE 127 + #define E5_CHAIN_POS -1 + #endif + + /** + * Monitor L6470 drivers for error conditions like over temperature and over current. + * In the case of over temperature Marlin can decrease the drive until the error condition clears. + * Other detected conditions can be used to stop the current print. + * Relevant g-codes: + * M906 - I1/2/3/4/5 Set or get motor drive level using axis codes X, Y, Z, E. Report values if no axis codes given. + * I not present or I0 or I1 - X, Y, Z or E0 + * I2 - X2, Y2, Z2 or E1 + * I3 - Z3 or E3 + * I4 - E4 + * I5 - E5 + * M916 - Increase drive level until get thermal warning + * M917 - Find minimum current thresholds + * M918 - Increase speed until max or error + * M122 S0/1 - Report driver parameters + */ + //#define MONITOR_L6470_DRIVER_STATUS + + #if ENABLED(MONITOR_L6470_DRIVER_STATUS) + #define KVAL_HOLD_STEP_DOWN 1 + //#define L6470_STOP_ON_ERROR + #endif + +#endif // L6470 + +/** + * TWI/I2C BUS + * + * This feature is an EXPERIMENTAL feature so it shall not be used on production + * machines. Enabling this will allow you to send and receive I2C data from slave + * devices on the bus. + * + * ; Example #1 + * ; This macro send the string "Marlin" to the slave device with address 0x63 (99) + * ; It uses multiple M260 commands with one B arg + * M260 A99 ; Target slave address + * M260 B77 ; M + * M260 B97 ; a + * M260 B114 ; r + * M260 B108 ; l + * M260 B105 ; i + * M260 B110 ; n + * M260 S1 ; Send the current buffer + * + * ; Example #2 + * ; Request 6 bytes from slave device with address 0x63 (99) + * M261 A99 B5 + * + * ; Example #3 + * ; Example serial output of a M261 request + * echo:i2c-reply: from:99 bytes:5 data:hello + */ + +// @section i2cbus + +//#define EXPERIMENTAL_I2CBUS +#define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave + +// @section extras + +/** + * Photo G-code + * Add the M240 G-code to take a photo. + * The photo can be triggered by a digital pin or a physical movement. + */ +//#define PHOTO_GCODE +#if ENABLED(PHOTO_GCODE) + // A position to move to (and raise Z) before taking the photo + //#define PHOTO_POSITION { X_MAX_POS - 5, Y_MAX_POS, 0 } // { xpos, ypos, zraise } (M240 X Y Z) + //#define PHOTO_DELAY_MS 100 // (ms) Duration to pause before moving back (M240 P) + //#define PHOTO_RETRACT_MM 6.5 // (mm) E retract/recover for the photo move (M240 R S) + + // Canon RC-1 or homebrew digital camera trigger + // Data from: http://www.doc-diy.net/photo/rc-1_hacked/ + //#define PHOTOGRAPH_PIN 23 + + // Canon Hack Development Kit + // http://captain-slow.dk/2014/03/09/3d-printing-timelapses/ + //#define CHDK_PIN 4 + + // Optional second move with delay to trigger the camera shutter + //#define PHOTO_SWITCH_POSITION { X_MAX_POS, Y_MAX_POS } // { xpos, ypos } (M240 I J) + + // Duration to hold the switch or keep CHDK_PIN high + //#define PHOTO_SWITCH_MS 50 // (ms) (M240 D) +#endif + +/** + * Spindle & Laser control + * + * Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and + * to set spindle speed, spindle direction, and laser power. + * + * SuperPid is a router/spindle speed controller used in the CNC milling community. + * Marlin can be used to turn the spindle on and off. It can also be used to set + * the spindle speed from 5,000 to 30,000 RPM. + * + * You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V + * hardware PWM pin for the speed control and a pin for the rotation direction. + * + * See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details. + */ +//#define SPINDLE_FEATURE +//#define LASER_FEATURE +#if EITHER(SPINDLE_FEATURE, LASER_FEATURE) + #define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH + #define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power + #define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower + #define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power + #define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop + + #if ENABLED(SPINDLE_FEATURE) + //#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction + #define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction + #define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed + + /** + * The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power + * + * SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT + * where PWM duty cycle varies from 0 to 255 + * + * set the following for your controller (ALL MUST BE SET) + */ + #define SPEED_POWER_SLOPE 118.4 + #define SPEED_POWER_INTERCEPT 0 + #define SPEED_POWER_MIN 5000 + #define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM + #else + #define SPEED_POWER_SLOPE 0.3922 + #define SPEED_POWER_INTERCEPT 0 + #define SPEED_POWER_MIN 10 + #define SPEED_POWER_MAX 100 // 0-100% + #endif +#endif + +/** + * Coolant Control + * + * Add the M7, M8, and M9 commands to turn mist or flood coolant on and off. + * + * Note: COOLANT_MIST_PIN and/or COOLANT_FLOOD_PIN must also be defined. + */ +//#define COOLANT_CONTROL +#if ENABLED(COOLANT_CONTROL) + #define COOLANT_MIST // Enable if mist coolant is present + #define COOLANT_FLOOD // Enable if flood coolant is present + #define COOLANT_MIST_INVERT false // Set "true" if the on/off function is reversed + #define COOLANT_FLOOD_INVERT false // Set "true" if the on/off function is reversed +#endif + +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define FILWIDTH_ERROR_MARGIN 1.0 // (mm) If a measurement differs too much from nominal width ignore it + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + +/** + * CNC Coordinate Systems + * + * Enables G53 and G54-G59.3 commands to select coordinate systems + * and G92.1 to reset the workspace to native machine space. + */ +//#define CNC_COORDINATE_SYSTEMS + +/** + * Auto-report temperatures with M155 S + */ +#define AUTO_REPORT_TEMPERATURES + +/** + * Include capabilities in M115 output + */ +#define EXTENDED_CAPABILITIES_REPORT + +/** + * Expected Printer Check + * Add the M16 G-code to compare a string to the MACHINE_NAME. + * M16 with a non-matching string causes the printer to halt. + */ +//#define EXPECTED_PRINTER_CHECK + +/** + * Disable all Volumetric extrusion options + */ +//#define NO_VOLUMETRICS + +#if DISABLED(NO_VOLUMETRICS) + /** + * Volumetric extrusion default state + * Activate to make volumetric extrusion the default method, + * with DEFAULT_NOMINAL_FILAMENT_DIA as the default diameter. + * + * M200 D0 to disable, M200 Dn to set a new diameter. + */ + //#define VOLUMETRIC_DEFAULT_ON +#endif + +/** + * Enable this option for a leaner build of Marlin that removes all + * workspace offsets, simplifying coordinate transformations, leveling, etc. + * + * - M206 and M428 are disabled. + * - G92 will revert to its behavior from Marlin 1.0. + */ +//#define NO_WORKSPACE_OFFSETS + +/** + * Set the number of proportional font spaces required to fill up a typical character space. + * This can help to better align the output of commands like `G29 O` Mesh Output. + * + * For clients that use a fixed-width font (like OctoPrint), leave this set to 1.0. + * Otherwise, adjust according to your client and font. + */ +#define PROPORTIONAL_FONT_RATIO 1.0 + +/** + * Spend 28 bytes of SRAM to optimize the GCode parser + */ +#define FASTER_GCODE_PARSER + +/** + * CNC G-code options + * Support CNC-style G-code dialects used by laser cutters, drawing machine cams, etc. + * Note that G0 feedrates should be used with care for 3D printing (if used at all). + * High feedrates may cause ringing and harm print quality. + */ +//#define PAREN_COMMENTS // Support for parentheses-delimited comments +//#define GCODE_MOTION_MODES // Remember the motion mode (G0 G1 G2 G3 G5 G38.X) and apply for X Y Z E F, etc. + +// Enable and set a (default) feedrate for all G0 moves +//#define G0_FEEDRATE 3000 // (mm/m) +#ifdef G0_FEEDRATE + //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode +#endif + +/** + * Startup commands + * + * Execute certain G-code commands immediately after power-on. + */ +//#define STARTUP_COMMANDS "M17 Z" + +/** + * G-code Macros + * + * Add G-codes M810-M819 to define and run G-code macros. + * Macros are not saved to EEPROM. + */ +//#define GCODE_MACROS +#if ENABLED(GCODE_MACROS) + #define GCODE_MACROS_SLOTS 5 // Up to 10 may be used + #define GCODE_MACROS_SLOT_SIZE 50 // Maximum length of a single macro +#endif + +/** + * User-defined menu items that execute custom GCode + */ +//#define CUSTOM_USER_MENUS +#if ENABLED(CUSTOM_USER_MENUS) + //#define CUSTOM_USER_MENU_TITLE "Custom Commands" + #define USER_SCRIPT_DONE "M117 User Script Done" + #define USER_SCRIPT_AUDIBLE_FEEDBACK + //#define USER_SCRIPT_RETURN // Return to status screen after a script + + #define USER_DESC_1 "Home & UBL Info" + #define USER_GCODE_1 "G28\nG29 W" + + #define USER_DESC_2 "Preheat for " PREHEAT_1_LABEL + #define USER_GCODE_2 "M140 S" STRINGIFY(PREHEAT_1_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_1_TEMP_HOTEND) + + #define USER_DESC_3 "Preheat for " PREHEAT_2_LABEL + #define USER_GCODE_3 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_2_TEMP_HOTEND) + + #define USER_DESC_4 "Heat Bed/Home/Level" + #define USER_GCODE_4 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nG28\nG29" + + //#define USER_DESC_5 "Home & Info" + //#define USER_GCODE_5 "G28\nM503" +#endif + +/** + * Host Action Commands + * + * Define host streamer action commands in compliance with the standard. + * + * See https://reprap.org/wiki/G-code#Action_commands + * Common commands ........ poweroff, pause, paused, resume, resumed, cancel + * G29_RETRY_AND_RECOVER .. probe_rewipe, probe_failed + * + * Some features add reason codes to extend these commands. + * + * Host Prompt Support enables Marlin to use the host for user prompts so + * filament runout and other processes can be managed from the host side. + */ +//#define HOST_ACTION_COMMANDS +#if ENABLED(HOST_ACTION_COMMANDS) + //#define HOST_PROMPT_SUPPORT +#endif + +/** + * I2C position encoders for closed loop control. + * Developed by Chris Barr at Aus3D. + * + * Wiki: http://wiki.aus3d.com.au/Magnetic_Encoder + * Github: https://github.com/Aus3D/MagneticEncoder + * + * Supplier: http://aus3d.com.au/magnetic-encoder-module + * Alternative Supplier: http://reliabuild3d.com/ + * + * Reliabuild encoders have been modified to improve reliability. + */ + +//#define I2C_POSITION_ENCODERS +#if ENABLED(I2C_POSITION_ENCODERS) + + #define I2CPE_ENCODER_CNT 1 // The number of encoders installed; max of 5 + // encoders supported currently. + + #define I2CPE_ENC_1_ADDR I2CPE_PRESET_ADDR_X // I2C address of the encoder. 30-200. + #define I2CPE_ENC_1_AXIS X_AXIS // Axis the encoder module is installed on. _AXIS. + #define I2CPE_ENC_1_TYPE I2CPE_ENC_TYPE_LINEAR // Type of encoder: I2CPE_ENC_TYPE_LINEAR -or- + // I2CPE_ENC_TYPE_ROTARY. + #define I2CPE_ENC_1_TICKS_UNIT 2048 // 1024 for magnetic strips with 2mm poles; 2048 for + // 1mm poles. For linear encoders this is ticks / mm, + // for rotary encoders this is ticks / revolution. + //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper + // steps per full revolution (motor steps/rev * microstepping) + //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the + // printer will attempt to correct the error; errors + // smaller than this are ignored to minimize effects of + // measurement noise / latency (filter). + + #define I2CPE_ENC_2_ADDR I2CPE_PRESET_ADDR_Y // Same as above, but for encoder 2. + #define I2CPE_ENC_2_AXIS Y_AXIS + #define I2CPE_ENC_2_TYPE I2CPE_ENC_TYPE_LINEAR + #define I2CPE_ENC_2_TICKS_UNIT 2048 + //#define I2CPE_ENC_2_TICKS_REV (16 * 200) + //#define I2CPE_ENC_2_INVERT + #define I2CPE_ENC_2_EC_METHOD I2CPE_ECM_MICROSTEP + #define I2CPE_ENC_2_EC_THRESH 0.10 + + #define I2CPE_ENC_3_ADDR I2CPE_PRESET_ADDR_Z // Encoder 3. Add additional configuration options + #define I2CPE_ENC_3_AXIS Z_AXIS // as above, or use defaults below. + + #define I2CPE_ENC_4_ADDR I2CPE_PRESET_ADDR_E // Encoder 4. + #define I2CPE_ENC_4_AXIS E_AXIS + + #define I2CPE_ENC_5_ADDR 34 // Encoder 5. + #define I2CPE_ENC_5_AXIS E_AXIS + + // Default settings for encoders which are enabled, but without settings configured above. + #define I2CPE_DEF_TYPE I2CPE_ENC_TYPE_LINEAR + #define I2CPE_DEF_ENC_TICKS_UNIT 2048 + #define I2CPE_DEF_TICKS_REV (16 * 200) + #define I2CPE_DEF_EC_METHOD I2CPE_ECM_NONE + #define I2CPE_DEF_EC_THRESH 0.1 + + //#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given + // axis after which the printer will abort. Comment out to + // disable abort behavior. + + #define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault + // for this amount of time (in ms) before the encoder + // is trusted again. + + /** + * Position is checked every time a new command is executed from the buffer but during long moves, + * this setting determines the minimum update time between checks. A value of 100 works well with + * error rolling average when attempting to correct only for skips and not for vibration. + */ + #define I2CPE_MIN_UPD_TIME_MS 4 // (ms) Minimum time between encoder checks. + + // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise. + #define I2CPE_ERR_ROLLING_AVERAGE + +#endif // I2C_POSITION_ENCODERS + +/** + * Analog Joystick(s) + */ +//#define JOYSTICK +#if ENABLED(JOYSTICK) + #define JOY_X_PIN 5 // RAMPS: Suggested pin A5 on AUX2 + #define JOY_Y_PIN 10 // RAMPS: Suggested pin A10 on AUX2 + #define JOY_Z_PIN 12 // RAMPS: Suggested pin A12 on AUX2 + #define JOY_EN_PIN 44 // RAMPS: Suggested pin D44 on AUX2 + + // Use M119 to find reasonable values after connecting your hardware: + #define JOY_X_LIMITS { 5600, 8190-100, 8190+100, 10800 } // min, deadzone start, deadzone end, max + #define JOY_Y_LIMITS { 5600, 8250-100, 8250+100, 11000 } + #define JOY_Z_LIMITS { 4800, 8080-100, 8080+100, 11550 } +#endif + +/** + * MAX7219 Debug Matrix + * + * Add support for a low-cost 8x8 LED Matrix based on the Max7219 chip as a realtime status display. + * Requires 3 signal wires. Some useful debug options are included to demonstrate its usage. + */ +//#define MAX7219_DEBUG +#if ENABLED(MAX7219_DEBUG) + #define MAX7219_CLK_PIN 64 + #define MAX7219_DIN_PIN 57 + #define MAX7219_LOAD_PIN 44 + + //#define MAX7219_GCODE // Add the M7219 G-code to control the LED matrix + #define MAX7219_INIT_TEST 2 // Do a test pattern at initialization (Set to 2 for spiral) + #define MAX7219_NUMBER_UNITS 1 // Number of Max7219 units in chain. + #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) + // connector at: right=0 bottom=-90 top=90 left=180 + //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side + + /** + * Sample debug features + * If you add more debug displays, be careful to avoid conflicts! + */ + #define MAX7219_DEBUG_PRINTER_ALIVE // Blink corner LED of 8x8 matrix to show that the firmware is functioning + #define MAX7219_DEBUG_PLANNER_HEAD 3 // Show the planner queue head position on this and the next LED matrix row + #define MAX7219_DEBUG_PLANNER_TAIL 5 // Show the planner queue tail position on this and the next LED matrix row + + #define MAX7219_DEBUG_PLANNER_QUEUE 0 // Show the current planner queue depth on this and the next LED matrix row + // If you experience stuttering, reboots, etc. this option can reveal how + // tweaks made to the configuration are affecting the printer in real-time. +#endif + +/** + * NanoDLP Sync support + * + * Add support for Synchronized Z moves when using with NanoDLP. G0/G1 axis moves will output "Z_move_comp" + * string to enable synchronization with DLP projector exposure. This change will allow to use + * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands + */ +//#define NANODLP_Z_SYNC +#if ENABLED(NANODLP_Z_SYNC) + //#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move. + // Default behavior is limited to Z axis only. +#endif + +/** + * WiFi Support (Espressif ESP32 WiFi) + */ +//#define WIFISUPPORT +#if ENABLED(WIFISUPPORT) + #define WIFI_SSID "Wifi SSID" + #define WIFI_PWD "Wifi Password" + //#define WEBSUPPORT // Start a webserver with auto-discovery + //#define OTASUPPORT // Support over-the-air firmware updates +#endif + +/** + * Prusa Multi-Material Unit v2 + * Enable in Configuration.h + */ +#if ENABLED(PRUSA_MMU2) + + // Serial port used for communication with MMU2. + // For AVR enable the UART port used for the MMU. (e.g., internalSerial) + // For 32-bit boards check your HAL for available serial ports. (e.g., Serial2) + #define INTERNAL_SERIAL_PORT 2 + #define MMU2_SERIAL internalSerial + + // Use hardware reset for MMU if a pin is defined for it + //#define MMU2_RST_PIN 23 + + // Enable if the MMU2 has 12V stepper motors (MMU2 Firmware 1.0.2 and up) + //#define MMU2_MODE_12V + + // G-code to execute when MMU2 F.I.N.D.A. probe detects filament runout + #define MMU2_FILAMENT_RUNOUT_SCRIPT "M600" + + // Add an LCD menu for MMU2 + //#define MMU2_MENUS + #if ENABLED(MMU2_MENUS) + // Settings for filament load / unload from the LCD menu. + // This is for Prusa MK3-style extruders. Customize for your hardware. + #define MMU2_FILAMENTCHANGE_EJECT_FEED 80.0 + #define MMU2_LOAD_TO_NOZZLE_SEQUENCE \ + { 7.2, 562 }, \ + { 14.4, 871 }, \ + { 36.0, 1393 }, \ + { 14.4, 871 }, \ + { 50.0, 198 } + + #define MMU2_RAMMING_SEQUENCE \ + { 1.0, 1000 }, \ + { 1.0, 1500 }, \ + { 2.0, 2000 }, \ + { 1.5, 3000 }, \ + { 2.5, 4000 }, \ + { -15.0, 5000 }, \ + { -14.0, 1200 }, \ + { -6.0, 600 }, \ + { 10.0, 700 }, \ + { -10.0, 400 }, \ + { -50.0, 2000 } + + #endif + + //#define MMU2_DEBUG // Write debug info to serial output + +#endif // PRUSA_MMU2 + +/** + * Advanced Print Counter settings + */ +#if ENABLED(PRINTCOUNTER) + #define SERVICE_WARNING_BUZZES 3 + // Activate up to 3 service interval watchdogs + //#define SERVICE_NAME_1 "Service S" + //#define SERVICE_INTERVAL_1 100 // print hours + //#define SERVICE_NAME_2 "Service L" + //#define SERVICE_INTERVAL_2 200 // print hours + //#define SERVICE_NAME_3 "Service 3" + //#define SERVICE_INTERVAL_3 1 // print hours +#endif + +// @section develop + +/** + * M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins + */ +//#define PINS_DEBUGGING + +// Enable Marlin dev mode which adds some special commands +//#define MARLIN_DEV_MODE diff --git a/config/examples/Velleman/K8400/Single-head/README.md b/config/examples/Velleman/K8400/Single-head/README.md new file mode 100644 index 0000000000..1ebdd16ef2 --- /dev/null +++ b/config/examples/Velleman/K8400/Single-head/README.md @@ -0,0 +1,15 @@ +# Configuration for Velleman K8400 Vertex +http://www.k8400.eu/ + +Configuration files for the K8400, ported upstream from the official Velleman firmware. +Like its predecessor, (K8200), the K8400 is a 3Drag clone. There are some minor differences, documented in pins_K8400.h. + +Single and dual head configurations provided. Copy the correct Configuration.h and Configuration_adv.h to the /src/config directory. + +**NOTE: This configuration includes the community sourced feed rate fix. Use 100% feed rate in Repetier!** + +For implementation and updated K8400 firmware, see https://github.com/birkett/Velleman-K8400-Firmware + +### Original Sources +Credit to Velleman for the original 1.0.x based code:
+http://www.vertex3dprinter.eu/downloads/files/vertex/firmware/vertex-m1-v1.4-h2.zip