add full speed option
This commit is contained in:
Bob-the-Kuhn
parent
cbcd1ed42d
commit
23760d6c14
|
|
@ -88,11 +88,17 @@
|
|||
//! To define a Low speed device
|
||||
//#define USB_DEVICE_LOW_SPEED
|
||||
|
||||
//! To define a Full speed device
|
||||
//#define USB_DEVICE_FULL_SPEED
|
||||
|
||||
|
||||
//! To authorize the High speed
|
||||
#ifndef USB_DEVICE_FULL_SPEED
|
||||
#if (UC3A3||UC3A4)
|
||||
# define USB_DEVICE_HS_SUPPORT
|
||||
//# define USB_DEVICE_HS_SUPPORT
|
||||
#elif (SAM3XA||SAM3U)
|
||||
# define USB_DEVICE_HS_SUPPORT
|
||||
//# define USB_DEVICE_HS_SUPPORT
|
||||
#endif
|
||||
#endif
|
||||
//@}
|
||||
|
||||
|
|
|
|||
|
|
@ -1,302 +0,0 @@
|
|||
/**
|
||||
* \file
|
||||
*
|
||||
* \brief USB configuration file
|
||||
*
|
||||
* Copyright (c) 2011-2015 Atmel Corporation. All rights reserved.
|
||||
*
|
||||
* \asf_license_start
|
||||
*
|
||||
* \page License
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright notice,
|
||||
* this list of conditions and the following disclaimer.
|
||||
*
|
||||
* 2. Redistributions in binary form must reproduce the above copyright notice,
|
||||
* this list of conditions and the following disclaimer in the documentation
|
||||
* and/or other materials provided with the distribution.
|
||||
*
|
||||
* 3. The name of Atmel may not be used to endorse or promote products derived
|
||||
* from this software without specific prior written permission.
|
||||
*
|
||||
* 4. This software may only be redistributed and used in connection with an
|
||||
* Atmel microcontroller product.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR IMPLIED
|
||||
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
|
||||
* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
|
||||
* EXPRESSLY AND SPECIFICALLY DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR
|
||||
* ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
||||
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
|
||||
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
||||
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
|
||||
* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
* \asf_license_stop
|
||||
*
|
||||
*/
|
||||
/*
|
||||
* Support and FAQ: visit <a href="http://www.atmel.com/design-support/">Atmel Support</a>
|
||||
*/
|
||||
|
||||
#ifndef _CONF_USB_H_
|
||||
#define _CONF_USB_H_
|
||||
|
||||
#undef UNUSED /* To avoid a macro clash as macros.h already defines it */
|
||||
#include "../../../core/macros.h" /* For ENABLED()/DISABLED() */
|
||||
#include "../../../../Configuration.h" /* For CUSTOM_MACHINE_NAME definition - We just need the name, no C++ allowed! */
|
||||
#include "compiler.h"
|
||||
|
||||
|
||||
/**
|
||||
* USB Device Configuration
|
||||
* @{
|
||||
*/
|
||||
|
||||
//! Device definition (mandatory)
|
||||
#define USB_DEVICE_VENDOR_ID 0x03EB /* ATMEL VID */
|
||||
#define USB_DEVICE_PRODUCT_ID 0x2424 /* MSC / CDC */
|
||||
#define USB_DEVICE_MAJOR_VERSION 1
|
||||
#define USB_DEVICE_MINOR_VERSION 0
|
||||
#define USB_DEVICE_POWER 100 // Consumption on Vbus line (mA)
|
||||
#define USB_DEVICE_ATTR \
|
||||
(USB_CONFIG_ATTR_SELF_POWERED)
|
||||
// (USB_CONFIG_ATTR_BUS_POWERED)
|
||||
// (USB_CONFIG_ATTR_REMOTE_WAKEUP|USB_CONFIG_ATTR_SELF_POWERED)
|
||||
// (USB_CONFIG_ATTR_REMOTE_WAKEUP|USB_CONFIG_ATTR_BUS_POWERED)
|
||||
|
||||
//! USB Device string definitions (Optional)
|
||||
#define USB_DEVICE_MANUFACTURE_NAME "marlinfw.org"
|
||||
#ifdef CUSTOM_MACHINE_NAME
|
||||
#define USB_DEVICE_PRODUCT_NAME CUSTOM_MACHINE_NAME
|
||||
#else
|
||||
#define USB_DEVICE_PRODUCT_NAME "3D Printer"
|
||||
#endif
|
||||
#define USB_DEVICE_SERIAL_NAME "123985739853"
|
||||
|
||||
/**
|
||||
* Device speeds support
|
||||
* Low speed not supported by CDC and MSC
|
||||
* @{
|
||||
*/
|
||||
|
||||
//! To define a Low speed device
|
||||
//#define USB_DEVICE_LOW_SPEED
|
||||
|
||||
//! To define a Full speed device
|
||||
//#define USB_DEVICE_FULL_SPEED
|
||||
|
||||
|
||||
//! To authorize the High speed
|
||||
#ifndef USB_DEVICE_FULL_SPEED
|
||||
#if (UC3A3||UC3A4)
|
||||
//# define USB_DEVICE_HS_SUPPORT
|
||||
#elif (SAM3XA||SAM3U)
|
||||
//# define USB_DEVICE_HS_SUPPORT
|
||||
#endif
|
||||
#endif
|
||||
//@}
|
||||
|
||||
|
||||
/**
|
||||
* USB Device Callbacks definitions (Optional)
|
||||
* @{
|
||||
*/
|
||||
#define UDC_VBUS_EVENT(b_vbus_high)
|
||||
#define UDC_SOF_EVENT()
|
||||
#define UDC_SUSPEND_EVENT()
|
||||
#define UDC_RESUME_EVENT()
|
||||
#define UDC_GET_EXTRA_STRING() usb_task_extra_string()
|
||||
#define USB_DEVICE_SPECIFIC_REQUEST() usb_task_other_requests()
|
||||
//@}
|
||||
|
||||
/**
|
||||
* USB Device low level configuration
|
||||
* When only one interface is used, these configurations are defined by the class module.
|
||||
* For composite device, these configuration must be defined here
|
||||
* @{
|
||||
*/
|
||||
//! Control endpoint size
|
||||
#define USB_DEVICE_EP_CTRL_SIZE 64
|
||||
|
||||
//! Two interfaces for this device (CDC COM + CDC DATA + MSC)
|
||||
#define USB_DEVICE_NB_INTERFACE 3
|
||||
|
||||
//! 5 endpoints used by CDC and MSC interfaces
|
||||
#if SAM3U
|
||||
// (3 | USB_EP_DIR_IN) // CDC Notify endpoint
|
||||
// (6 | USB_EP_DIR_IN) // CDC TX
|
||||
// (5 | USB_EP_DIR_OUT) // CDC RX
|
||||
// (1 | USB_EP_DIR_IN) // MSC IN
|
||||
// (2 | USB_EP_DIR_OUT) // MSC OUT
|
||||
# define USB_DEVICE_MAX_EP 6
|
||||
# if defined(USB_DEVICE_HS_SUPPORT)
|
||||
// In HS mode, size of bulk endpoints are 512
|
||||
// If CDC and MSC endpoints all uses 2 banks, DPRAM is not enough: 4 bulk
|
||||
// endpoints requires 4K bytes. So reduce the number of banks of CDC bulk
|
||||
// endpoints to use less DPRAM. Keep MSC setting to keep MSC performance.
|
||||
# define UDD_BULK_NB_BANK(ep) ((ep == 5 || ep== 6) ? 1 : 2)
|
||||
#endif
|
||||
#else
|
||||
// (3 | USB_EP_DIR_IN) // CDC Notify endpoint
|
||||
// (4 | USB_EP_DIR_IN) // CDC TX
|
||||
// (5 | USB_EP_DIR_OUT) // CDC RX
|
||||
// (1 | USB_EP_DIR_IN) // MSC IN
|
||||
// (2 | USB_EP_DIR_OUT) // MSC OUT
|
||||
# define USB_DEVICE_MAX_EP 5
|
||||
# if SAM3XA && defined(USB_DEVICE_HS_SUPPORT)
|
||||
// In HS mode, size of bulk endpoints are 512
|
||||
// If CDC and MSC endpoints all uses 2 banks, DPRAM is not enough: 4 bulk
|
||||
// endpoints requires 4K bytes. So reduce the number of banks of CDC bulk
|
||||
// endpoints to use less DPRAM. Keep MSC setting to keep MSC performance.
|
||||
# define UDD_BULK_NB_BANK(ep) ((ep == 4 || ep== 5) ? 1 : 2)
|
||||
# endif
|
||||
#endif
|
||||
//@}
|
||||
|
||||
//@}
|
||||
|
||||
|
||||
/**
|
||||
* USB Interface Configuration
|
||||
* @{
|
||||
*/
|
||||
/**
|
||||
* Configuration of CDC interface
|
||||
* @{
|
||||
*/
|
||||
|
||||
//! Define one USB communication ports
|
||||
#define UDI_CDC_PORT_NB 1
|
||||
|
||||
//! Interface callback definition
|
||||
#define UDI_CDC_ENABLE_EXT(port) usb_task_cdc_enable(port)
|
||||
#define UDI_CDC_DISABLE_EXT(port) usb_task_cdc_disable(port)
|
||||
#define UDI_CDC_RX_NOTIFY(port) usb_task_cdc_rx_notify(port)
|
||||
#define UDI_CDC_TX_EMPTY_NOTIFY(port)
|
||||
#define UDI_CDC_SET_CODING_EXT(port,cfg) usb_task_cdc_config(port,cfg)
|
||||
#define UDI_CDC_SET_DTR_EXT(port,set) usb_task_cdc_set_dtr(port,set)
|
||||
#define UDI_CDC_SET_RTS_EXT(port,set)
|
||||
|
||||
//! Define it when the transfer CDC Device to Host is a low rate (<512000 bauds)
|
||||
//! to reduce CDC buffers size
|
||||
//#define UDI_CDC_LOW_RATE
|
||||
|
||||
//! Default configuration of communication port
|
||||
#define UDI_CDC_DEFAULT_RATE 115200
|
||||
#define UDI_CDC_DEFAULT_STOPBITS CDC_STOP_BITS_1
|
||||
#define UDI_CDC_DEFAULT_PARITY CDC_PAR_NONE
|
||||
#define UDI_CDC_DEFAULT_DATABITS 8
|
||||
|
||||
//! Enable id string of interface to add an extra USB string
|
||||
#define UDI_CDC_IAD_STRING_ID 4
|
||||
|
||||
/**
|
||||
* USB CDC low level configuration
|
||||
* In standalone these configurations are defined by the CDC module.
|
||||
* For composite device, these configuration must be defined here
|
||||
* @{
|
||||
*/
|
||||
//! Endpoint numbers definition
|
||||
#if SAM3U
|
||||
# define UDI_CDC_COMM_EP_0 (3 | USB_EP_DIR_IN) // Notify endpoint
|
||||
# define UDI_CDC_DATA_EP_IN_0 (6 | USB_EP_DIR_IN) // TX
|
||||
# define UDI_CDC_DATA_EP_OUT_0 (5 | USB_EP_DIR_OUT)// RX
|
||||
#else
|
||||
# define UDI_CDC_COMM_EP_0 (3 | USB_EP_DIR_IN) // Notify endpoint
|
||||
# define UDI_CDC_DATA_EP_IN_0 (4 | USB_EP_DIR_IN) // TX
|
||||
# define UDI_CDC_DATA_EP_OUT_0 (5 | USB_EP_DIR_OUT)// RX
|
||||
#endif
|
||||
|
||||
//! Interface numbers
|
||||
#define UDI_CDC_COMM_IFACE_NUMBER_0 0
|
||||
#define UDI_CDC_DATA_IFACE_NUMBER_0 1
|
||||
//@}
|
||||
//@}
|
||||
|
||||
|
||||
/**
|
||||
* Configuration of MSC interface
|
||||
* @{
|
||||
*/
|
||||
//! Vendor name and Product version of MSC interface
|
||||
#define UDI_MSC_GLOBAL_VENDOR_ID \
|
||||
'M', 'A', 'R', 'L', 'I', 'N', '3', 'D'
|
||||
#define UDI_MSC_GLOBAL_PRODUCT_VERSION \
|
||||
'1', '.', '0', '0'
|
||||
|
||||
//! Interface callback definition
|
||||
#define UDI_MSC_ENABLE_EXT() usb_task_msc_enable()
|
||||
#define UDI_MSC_DISABLE_EXT() usb_task_msc_disable()
|
||||
|
||||
//! Enable id string of interface to add an extra USB string
|
||||
#define UDI_MSC_STRING_ID 5
|
||||
|
||||
/**
|
||||
* USB MSC low level configuration
|
||||
* In standalone these configurations are defined by the MSC module.
|
||||
* For composite device, these configuration must be defined here
|
||||
* @{
|
||||
*/
|
||||
//! Endpoint numbers definition
|
||||
#define UDI_MSC_EP_IN (1 | USB_EP_DIR_IN)
|
||||
#define UDI_MSC_EP_OUT (2 | USB_EP_DIR_OUT)
|
||||
|
||||
//! Interface number
|
||||
#define UDI_MSC_IFACE_NUMBER 2
|
||||
//@}
|
||||
//@}
|
||||
|
||||
//@}
|
||||
|
||||
|
||||
/**
|
||||
* Description of Composite Device
|
||||
* @{
|
||||
*/
|
||||
//! USB Interfaces descriptor structure
|
||||
#define UDI_COMPOSITE_DESC_T \
|
||||
usb_iad_desc_t udi_cdc_iad; \
|
||||
udi_cdc_comm_desc_t udi_cdc_comm; \
|
||||
udi_cdc_data_desc_t udi_cdc_data; \
|
||||
udi_msc_desc_t udi_msc
|
||||
|
||||
//! USB Interfaces descriptor value for Full Speed
|
||||
#define UDI_COMPOSITE_DESC_FS \
|
||||
.udi_cdc_iad = UDI_CDC_IAD_DESC_0, \
|
||||
.udi_cdc_comm = UDI_CDC_COMM_DESC_0, \
|
||||
.udi_cdc_data = UDI_CDC_DATA_DESC_0_FS, \
|
||||
.udi_msc = UDI_MSC_DESC_FS
|
||||
|
||||
//! USB Interfaces descriptor value for High Speed
|
||||
#define UDI_COMPOSITE_DESC_HS \
|
||||
.udi_cdc_iad = UDI_CDC_IAD_DESC_0, \
|
||||
.udi_cdc_comm = UDI_CDC_COMM_DESC_0, \
|
||||
.udi_cdc_data = UDI_CDC_DATA_DESC_0_HS, \
|
||||
.udi_msc = UDI_MSC_DESC_HS
|
||||
|
||||
//! USB Interface APIs
|
||||
#define UDI_COMPOSITE_API \
|
||||
&udi_api_cdc_comm, \
|
||||
&udi_api_cdc_data, \
|
||||
&udi_api_msc
|
||||
//@}
|
||||
|
||||
|
||||
/**
|
||||
* USB Device Driver Configuration
|
||||
* @{
|
||||
*/
|
||||
//@}
|
||||
|
||||
//! The includes of classes and other headers must be done at the end of this file to avoid compile error
|
||||
#include "udi_cdc.h"
|
||||
#include "udi_msc.h"
|
||||
#include "usb_task.h"
|
||||
|
||||
#endif // _CONF_USB_H_
|
||||
Loading…
Reference in a new issue