BTT Motor Expansion for SKR Pro (#20123)
This commit is contained in:
Minims
Scott Lahteine
parent
90f3d1f7a6
commit
2b63a1b4e1
|
|
@ -25,6 +25,13 @@
|
|||
#error "Oops! Select an STM32F4 board in 'Tools > Board.'"
|
||||
#endif
|
||||
|
||||
// BigTreeTech driver expansion module https://bit.ly/3ptRRoj
|
||||
//#define BTT_MOTOR_EXPANSION
|
||||
|
||||
#if BOTH(HAS_WIRED_LCD, BTT_MOTOR_EXPANSION)
|
||||
#error "It's not possible to have both LCD and motor expansion module on EXP1/EXP2."
|
||||
#endif
|
||||
|
||||
// Use one of these or SDCard-based Emulation will be used
|
||||
#if NO_EEPROM_SELECTED
|
||||
//#define SRAM_EEPROM_EMULATION // Use BackSRAM-based EEPROM emulation
|
||||
|
|
@ -247,14 +254,43 @@
|
|||
#define SDCARD_CONNECTION LCD
|
||||
#endif
|
||||
|
||||
/**
|
||||
* ----- -----
|
||||
* NC | 1 2 | GND 5V | 1 2 | GND
|
||||
* RESET | 3 4 | PF12(SD_DETECT) (LCD_D7) PG7 | 3 4 | PG6 (LCD_D6)
|
||||
* (MOSI)PB15 | 5 6 PF11(BTN_EN2) (LCD_D5) PG3 | 5 6 PG2 (LCD_D4)
|
||||
* (SD_SS)PB12 | 7 8 | PG10(BTN_EN1) (LCD_RS) PD10 | 7 8 | PD11 (LCD_EN)
|
||||
* (SCK)PB13 | 9 10| PB14(MISO) (BTN_ENC) PA8 | 9 10| PG4 (BEEPER)
|
||||
* ----- -----
|
||||
* EXP2 EXP1
|
||||
*/
|
||||
|
||||
#define EXPA1_03_PIN PG7
|
||||
#define EXPA1_04_PIN PG6
|
||||
#define EXPA1_05_PIN PG3
|
||||
#define EXPA1_06_PIN PG2
|
||||
#define EXPA1_07_PIN PD10
|
||||
#define EXPA1_08_PIN PD11
|
||||
#define EXPA1_09_PIN PA8
|
||||
#define EXPA1_10_PIN PG4
|
||||
|
||||
#define EXPA2_03_PIN -1
|
||||
#define EXPA2_04_PIN PF12
|
||||
#define EXPA2_05_PIN PB15
|
||||
#define EXPA2_06_PIN PF11
|
||||
#define EXPA2_07_PIN PB12
|
||||
#define EXPA2_08_PIN PG10
|
||||
#define EXPA2_09_PIN PB13
|
||||
#define EXPA2_10_PIN PB14
|
||||
|
||||
//
|
||||
// Onboard SD card
|
||||
// Must use soft SPI because Marlin's default hardware SPI is tied to LCD's EXP2
|
||||
//
|
||||
#if SD_CONNECTION_IS(LCD)
|
||||
|
||||
#define SD_DETECT_PIN PF12
|
||||
#define SDSS PB12
|
||||
#define SD_DETECT_PIN EXPA2_04_PIN
|
||||
#define SDSS EXPA2_07_PIN
|
||||
|
||||
#elif SD_CONNECTION_IS(ONBOARD)
|
||||
|
||||
|
|
@ -273,16 +309,52 @@
|
|||
#error "CUSTOM_CABLE is not a supported SDCARD_CONNECTION for this board"
|
||||
#endif
|
||||
|
||||
/**
|
||||
* ----- -----
|
||||
* NC | · · | GND 5V | · · | GND
|
||||
* RESET | · · | PF12(SD_DETECT) (LCD_D7) PG7 | · · | PG6 (LCD_D6)
|
||||
* (MOSI)PB15 | · · | PF11(BTN_EN2) (LCD_D5) PG3 | · · | PG2 (LCD_D4)
|
||||
* (SD_SS)PB12 | · · | PG10(BTN_EN1) (LCD_RS) PD10 | · · | PD11 (LCD_EN)
|
||||
* (SCK)PB13 | · · | PB14(MISO) (BTN_ENC) PA8 | · · | PG4 (BEEPER)
|
||||
* ----- -----
|
||||
* EXP2 EXP1
|
||||
*/
|
||||
#if ENABLED(BTT_MOTOR_EXPANSION)
|
||||
/**
|
||||
* _____ _____
|
||||
* NC | · · | GND NC | · · | GND
|
||||
* NC | · · | PF12 (M1EN) (M2EN) PG7 | · · | PG6 (M3EN)
|
||||
* (M1STP) PB15 | · · PF11 (M1DIR) (M1RX) PG3 | · · PG2 (M1DIAG)
|
||||
* (M2DIR) PB12 | · · | PG10 (M2STP) (M2RX) PD10 | · · | PD11 (M2DIAG)
|
||||
* (M3DIR) PB13 | · · | PB14 (M3STP) (M3RX) PA8 | · · | PG4 (M3DIAG)
|
||||
* ----- -----
|
||||
* EXP2 EXP1
|
||||
*/
|
||||
|
||||
// M1 on Driver Expansion Module
|
||||
#define E3_STEP_PIN EXPA2_05_PIN
|
||||
#define E3_DIR_PIN EXPA2_06_PIN
|
||||
#define E3_ENABLE_PIN EXPA2_04_PIN
|
||||
#define E3_DIAG_PIN EXPA1_06_PIN
|
||||
#define E3_CS_PIN EXPA1_05_PIN
|
||||
#if HAS_TMC_UART
|
||||
#define E3_SERIAL_TX_PIN EXPA1_05_PIN
|
||||
#define E3_SERIAL_RX_PIN EXPA1_05_PIN
|
||||
#endif
|
||||
|
||||
// M2 on Driver Expansion Module
|
||||
#define E4_STEP_PIN EXPA2_08_PIN
|
||||
#define E4_DIR_PIN EXPA2_07_PIN
|
||||
#define E4_ENABLE_PIN EXPA1_03_PIN
|
||||
#define E4_DIAG_PIN EXPA1_08_PIN
|
||||
#define E4_CS_PIN EXPA1_07_PIN
|
||||
#if HAS_TMC_UART
|
||||
#define E4_SERIAL_TX_PIN EXPA1_07_PIN
|
||||
#define E4_SERIAL_RX_PIN EXPA1_07_PIN
|
||||
#endif
|
||||
|
||||
// M3 on Driver Expansion Module
|
||||
#define E5_STEP_PIN EXPA2_10_PIN
|
||||
#define E5_DIR_PIN EXPA2_09_PIN
|
||||
#define E5_ENABLE_PIN EXPA1_04_PIN
|
||||
#define E5_DIAG_PIN EXPA1_10_PIN
|
||||
#define E5_CS_PIN EXPA1_09_PIN
|
||||
#if HAS_TMC_UART
|
||||
#define E5_SERIAL_TX_PIN EXPA1_09_PIN
|
||||
#define E5_SERIAL_RX_PIN EXPA1_09_PIN
|
||||
#endif
|
||||
|
||||
#endif // BTT_MOTOR_EXPANSION
|
||||
|
||||
//
|
||||
// LCDs and Controllers
|
||||
|
|
@ -290,23 +362,23 @@
|
|||
#if IS_TFTGLCD_PANEL
|
||||
|
||||
#if ENABLED(TFTGLCD_PANEL_SPI)
|
||||
#define TFTGLCD_CS PG10
|
||||
#define TFTGLCD_CS EXPA2_08_PIN
|
||||
#endif
|
||||
|
||||
#elif HAS_WIRED_LCD
|
||||
|
||||
#define BEEPER_PIN PG4
|
||||
#define BTN_ENC PA8
|
||||
#define BEEPER_PIN EXPA1_10_PIN
|
||||
#define BTN_ENC EXPA1_09_PIN
|
||||
|
||||
#if ENABLED(CR10_STOCKDISPLAY)
|
||||
|
||||
#define LCD_PINS_RS PG6
|
||||
#define LCD_PINS_RS EXPA1_04_PIN
|
||||
|
||||
#define BTN_EN1 PD11
|
||||
#define BTN_EN2 PG2
|
||||
#define BTN_EN1 EXPA1_08_PIN
|
||||
#define BTN_EN2 EXPA1_06_PIN
|
||||
|
||||
#define LCD_PINS_ENABLE PG7
|
||||
#define LCD_PINS_D4 PG3
|
||||
#define LCD_PINS_ENABLE EXPA1_03_PIN
|
||||
#define LCD_PINS_D4 EXPA1_05_PIN
|
||||
|
||||
// CR10_STOCKDISPLAY default timing is too fast
|
||||
#undef BOARD_ST7920_DELAY_1
|
||||
|
|
@ -315,45 +387,45 @@
|
|||
|
||||
#elif ENABLED(MKS_MINI_12864)
|
||||
|
||||
#define DOGLCD_A0 PG6
|
||||
#define DOGLCD_CS PG3
|
||||
#define BTN_EN1 PG10
|
||||
#define BTN_EN2 PF11
|
||||
#define DOGLCD_A0 EXPA1_04_PIN
|
||||
#define DOGLCD_CS EXPA1_05_PIN
|
||||
#define BTN_EN1 EXPA2_08_PIN
|
||||
#define BTN_EN2 EXPA2_06_PIN
|
||||
|
||||
#else
|
||||
|
||||
#define LCD_PINS_RS PD10
|
||||
#define LCD_PINS_RS EXPA1_07_PIN
|
||||
|
||||
#define BTN_EN1 PG10
|
||||
#define BTN_EN2 PF11
|
||||
#define BTN_EN1 EXPA2_08_PIN
|
||||
#define BTN_EN2 EXPA2_06_PIN
|
||||
|
||||
#define LCD_PINS_ENABLE PD11
|
||||
#define LCD_PINS_D4 PG2
|
||||
#define LCD_PINS_ENABLE EXPA1_08_PIN
|
||||
#define LCD_PINS_D4 EXPA1_06_PIN
|
||||
|
||||
#if ENABLED(FYSETC_MINI_12864)
|
||||
#define DOGLCD_CS PD11
|
||||
#define DOGLCD_A0 PD10
|
||||
#define DOGLCD_CS EXPA1_08_PIN
|
||||
#define DOGLCD_A0 EXPA1_07_PIN
|
||||
//#define LCD_BACKLIGHT_PIN -1
|
||||
#define LCD_RESET_PIN PG2 // Must be high or open for LCD to operate normally.
|
||||
#define LCD_RESET_PIN EXPA1_06_PIN // Must be high or open for LCD to operate normally.
|
||||
#if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0)
|
||||
#ifndef RGB_LED_R_PIN
|
||||
#define RGB_LED_R_PIN PG3
|
||||
#define RGB_LED_R_PIN EXPA1_05_PIN
|
||||
#endif
|
||||
#ifndef RGB_LED_G_PIN
|
||||
#define RGB_LED_G_PIN PG6
|
||||
#define RGB_LED_G_PIN EXPA1_04_PIN
|
||||
#endif
|
||||
#ifndef RGB_LED_B_PIN
|
||||
#define RGB_LED_B_PIN PG7
|
||||
#define RGB_LED_B_PIN EXPA1_03_PIN
|
||||
#endif
|
||||
#elif ENABLED(FYSETC_MINI_12864_2_1)
|
||||
#define NEOPIXEL_PIN PG3
|
||||
#define NEOPIXEL_PIN EXPA1_05_PIN
|
||||
#endif
|
||||
#endif // !FYSETC_MINI_12864
|
||||
|
||||
#if IS_ULTIPANEL
|
||||
#define LCD_PINS_D5 PG3
|
||||
#define LCD_PINS_D6 PG6
|
||||
#define LCD_PINS_D7 PG7
|
||||
#define LCD_PINS_D5 EXPA1_05_PIN
|
||||
#define LCD_PINS_D6 EXPA1_04_PIN
|
||||
#define LCD_PINS_D7 EXPA1_03_PIN
|
||||
#endif
|
||||
|
||||
#endif
|
||||
|
|
|
|||
Loading…
Reference in a new issue