LCD Progress Bar

Marlin/Configuration_adv.h

@@ -297,6 +297,20 @@
 // using:
 //#define MENU_ADDAUTOSTART
 
+// Show a progress bar on the LCD when printing from SD?
+//#define LCD_PROGRESS_BAR
+
+#ifdef LCD_PROGRESS_BAR
+  // Amount of time (ms) to show the bar
+  #define PROGRESS_BAR_BAR_TIME 2000
+  // Amount of time (ms) to show the status message
+  #define PROGRESS_BAR_MSG_TIME 3000
+  // Amount of time (ms) to retain the status message (0=forever)
+  #define PROGRESS_MSG_EXPIRE   0
+  // Enable this to show messages for MSG_TIME then hide them
+  //#define PROGRESS_MSG_ONCE
+#endif
+
 // The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
 //#define USE_WATCHDOG
 
@@ -332,7 +346,7 @@
 
 // extruder advance constant (s2/mm3)
 //
-// advance (steps) = STEPS_PER_CUBIC_MM_E * EXTUDER_ADVANCE_K * cubic mm per second ^ 2
+// advance (steps) = STEPS_PER_CUBIC_MM_E * EXTRUDER_ADVANCE_K * cubic mm per second ^ 2
 //
 // Hooke's law says:		force = k * distance
 // Bernoulli's principle says:	v ^ 2 / 2 + g . h + pressure / density = constant

Marlin/example_configurations/SCARA/Configuration.h

@@ -756,6 +756,39 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 //#define SERVO_ENDSTOPS {-1, -1, 0} // Servo index for X, Y, Z. Disable with -1
 //#define SERVO_ENDSTOP_ANGLES {0,0, 0,0, 70,0} // X,Y,Z Axis Extend and Retract angles
 
+/**********************************************************************\
+ * Support for a filament diameter sensor
+ * Also allows adjustment of diameter at print time (vs  at slicing)
+ * Single extruder only at this point (extruder 0)
+ * 
+ * Motherboards
+ * 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector 
+ * 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E)
+ * 301 - Rambo  - uses Analog input 3
+ * Note may require analog pins to be defined for different motherboards
+ **********************************************************************/
+// Uncomment below to enable
+//#define FILAMENT_SENSOR
+
+#define FILAMENT_SENSOR_EXTRUDER_NUM  0  //The number of the extruder that has the filament sensor (0,1,2)
+#define MEASUREMENT_DELAY_CM      14  //measurement delay in cm.  This is the distance from filament sensor to middle of barrel
+
+#define DEFAULT_NOMINAL_FILAMENT_DIA  3.0  //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software.  Used for sensor reading validation
+#define MEASURED_UPPER_LIMIT          3.30  //upper limit factor used for sensor reading validation in mm
+#define MEASURED_LOWER_LIMIT          1.90  //lower limit factor for sensor reading validation in mm
+#define MAX_MEASUREMENT_DELAY     20  //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM  and lower number saves RAM)
+
+//defines used in the code
+#define DEFAULT_MEASURED_FILAMENT_DIA  DEFAULT_NOMINAL_FILAMENT_DIA  //set measured to nominal initially 
+
+//When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status.  Status will appear for 5 sec.
+//#define FILAMENT_LCD_DISPLAY
+
+
+
+
+
+
 #include "Configuration_adv.h"
 #include "thermistortables.h"
 

Marlin/example_configurations/SCARA/Configuration_adv.h

@@ -300,6 +300,20 @@
 // using:
 //#define MENU_ADDAUTOSTART
 
+// Show a progress bar on the LCD when printing from SD?
+//#define LCD_PROGRESS_BAR
+
+#ifdef LCD_PROGRESS_BAR
+  // Amount of time (ms) to show the bar
+  #define PROGRESS_BAR_BAR_TIME 2000
+  // Amount of time (ms) to show the status message
+  #define PROGRESS_BAR_MSG_TIME 3000
+  // Amount of time (ms) to retain the status message (0=forever)
+  #define PROGRESS_MSG_EXPIRE   0
+  // Enable this to show messages for MSG_TIME then hide them
+  //#define PROGRESS_MSG_ONCE
+#endif
+
 // The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
 //#define USE_WATCHDOG
 
@@ -340,7 +354,7 @@
 
 // extruder advance constant (s2/mm3)
 //
-// advance (steps) = STEPS_PER_CUBIC_MM_E * EXTUDER_ADVANCE_K * cubic mm per second ^ 2
+// advance (steps) = STEPS_PER_CUBIC_MM_E * EXTRUDER_ADVANCE_K * cubic mm per second ^ 2
 //
 // Hooke's law says:		force = k * distance
 // Bernoulli's principle says:	v ^ 2 / 2 + g . h + pressure / density = constant

Marlin/example_configurations/delta/Configuration.h

@@ -758,11 +758,13 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
  * 
  * Motherboards
  * 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector 
- * 81 - Printrboard - Uses Analog input 2 on the Aux 2 connector
+ * 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E)
  * 301 - Rambo  - uses Analog input 3
  * Note may require analog pins to be defined for different motherboards
  **********************************************************************/
-#define FILAMENT_SENSOR
+// Uncomment below to enable
+//#define FILAMENT_SENSOR
+
 #define FILAMENT_SENSOR_EXTRUDER_NUM  0  //The number of the extruder that has the filament sensor (0,1,2)
 #define MEASUREMENT_DELAY_CM      14  //measurement delay in cm.  This is the distance from filament sensor to middle of barrel
 
@@ -774,6 +776,9 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 //defines used in the code
 #define DEFAULT_MEASURED_FILAMENT_DIA  DEFAULT_NOMINAL_FILAMENT_DIA  //set measured to nominal initially 
 
+//When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status.  Status will appear for 5 sec.
+//#define FILAMENT_LCD_DISPLAY
+
 
 
 

Marlin/example_configurations/delta/Configuration_adv.h

@@ -292,6 +292,20 @@
 // using:
 //#define MENU_ADDAUTOSTART
 
+// Show a progress bar on the LCD when printing from SD
+//#define LCD_PROGRESS_BAR
+
+#ifdef LCD_PROGRESS_BAR
+  // Amount of time (ms) to show the bar
+  #define PROGRESS_BAR_BAR_TIME 2000
+  // Amount of time (ms) to show the status message
+  #define PROGRESS_BAR_MSG_TIME 2000
+  // Amount of time (ms) to retain the status message (0=forever)
+  #define PROGRESS_MSG_EXPIRE   0
+  // Enable this to show messages for MSG_TIME then hide them
+  //#define PROGRESS_MSG_ONCE
+#endif
+
 // The hardware watchdog should reset the Microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
 //#define USE_WATCHDOG
 
@@ -327,10 +341,10 @@
 
 // extruder advance constant (s2/mm3)
 //
-// advance (steps) = STEPS_PER_CUBIC_MM_E * EXTUDER_ADVANCE_K * cubic mm per second ^ 2
+// advance (steps) = STEPS_PER_CUBIC_MM_E * EXTRUDER_ADVANCE_K * cubic mm per second ^ 2
 //
 // hooke's law says:		force = k * distance
-// bernoulli's priniciple says:	v ^ 2 / 2 + g . h + pressure / density = constant
+// Bernoulli's principle says:	v ^ 2 / 2 + g . h + pressure / density = constant
 // so: v ^ 2 is proportional to number of steps we advance the extruder
 //#define ADVANCE
 

Marlin/example_configurations/makibox/Configuration.h

@@ -14,6 +14,13 @@
 // example_configurations/delta directory.
 //
 
+//===========================================================================
+//============================= SCARA Printer ===============================
+//===========================================================================
+// For a Delta printer replace the configuration files with the files in the
+// example_configurations/SCARA directory.
+//
+
 // User-specified version info of this build to display in [Pronterface, etc] terminal window during
 // startup. Implementation of an idea by Prof Braino to inform user that any changes made to this
 // build by the user have been successfully uploaded into firmware.
@@ -25,7 +32,6 @@
 // Serial port 0 is still used by the Arduino bootloader regardless of this setting.
 #define SERIAL_PORT 0
 
-// This determines the communication speed of the printer
 // This determines the communication speed of the printer
 #define BAUDRATE 250000
 
@@ -80,6 +86,7 @@
 // 10 is 100k RS thermistor 198-961 (4.7k pullup)
 // 11 is 100k beta 3950 1% thermistor (4.7k pullup)
 // 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
+// 13 is 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE" 
 // 20 is the PT100 circuit found in the Ultimainboard V2.x
 // 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
 //
@@ -145,7 +152,7 @@
                                   // is more then PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
   #define PID_INTEGRAL_DRIVE_MAX 255  //limit for the integral term
   #define K1 0.95 //smoothing factor within the PID
-  #define PID_dT ((OVERSAMPLENR * 8.0)/(F_CPU / 64.0 / 256.0)) //sampling period of the temperature routine
+  #define PID_dT ((OVERSAMPLENR * 10.0)/(F_CPU / 64.0 / 256.0)) //sampling period of the temperature routine
 
 // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
 // Ultimaker
@@ -214,6 +221,44 @@
 #define EXTRUDE_MINTEMP 170
 #define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
 
+/*================== Thermal Runaway Protection ==============================
+This is a feature to protect your printer from burn up in flames if it has
+a thermistor coming off place (this happened to a friend of mine recently and
+motivated me writing this feature).
+
+The issue: If a thermistor come off, it will read a lower temperature than actual.
+The system will turn the heater on forever, burning up the filament and anything
+else around.
+
+After the temperature reaches the target for the first time, this feature will 
+start measuring for how long the current temperature stays below the target 
+minus _HYSTERESIS (set_temperature - THERMAL_RUNAWAY_PROTECTION_HYSTERESIS).
+
+If it stays longer than _PERIOD, it means the thermistor temperature
+cannot catch up with the target, so something *may be* wrong. Then, to be on the
+safe side, the system will he halt.
+
+Bear in mind the count down will just start AFTER the first time the 
+thermistor temperature is over the target, so you will have no problem if
+your extruder heater takes 2 minutes to hit the target on heating.
+
+*/
+// If you want to enable this feature for all your extruder heaters,
+// uncomment the 2 defines below:
+
+// Parameters for all extruder heaters
+//#define THERMAL_RUNAWAY_PROTECTION_PERIOD 40 //in seconds
+//#define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 4 // in degree Celsius
+
+// If you want to enable this feature for your bed heater,
+// uncomment the 2 defines below:
+
+// Parameters for the bed heater
+//#define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 //in seconds
+//#define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius
+//===========================================================================
+
+
 //===========================================================================
 //=============================Mechanical Settings===========================
 //===========================================================================
@@ -269,6 +314,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 #define DISABLE_Y false
 #define DISABLE_Z false
 #define DISABLE_E false // For all extruders
+#define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled
 
 #define INVERT_X_DIR false    // for Mendel set to false, for Orca set to true
 #define INVERT_Y_DIR false    // for Mendel set to true, for Orca set to false
@@ -300,6 +346,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 //============================= Bed Auto Leveling ===========================
 
 //#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line)
+#define Z_PROBE_REPEATABILITY_TEST  // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
 
 #ifdef ENABLE_AUTO_BED_LEVELING
 
@@ -360,6 +407,8 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
   #define Z_RAISE_BEFORE_PROBING 15    //How much the extruder will be raised before traveling to the first probing point.
   #define Z_RAISE_BETWEEN_PROBINGS 5  //How much the extruder will be raised when traveling from between next probing points
 
+  //#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
+  //#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
 
   //If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk
   //The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it.
@@ -461,6 +510,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 //#define DOGLCD  // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
 #define SDSUPPORT // Enable SD Card Support in Hardware Console
 #define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error)
+//#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication
 //#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder
 //#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking
 //#define ULTIMAKERCONTROLLER //as available from the Ultimaker online store.
@@ -675,12 +725,42 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 // This allows for servo actuated endstops, primary usage is for the Z Axis to eliminate calibration or bed height changes.
 // Use M206 command to correct for switch height offset to actual nozzle height. Store that setting with M500.
 //
-
-#define DIGIPOT_I2C
-
 //#define SERVO_ENDSTOPS {-1, -1, 0} // Servo index for X, Y, Z. Disable with -1
 //#define SERVO_ENDSTOP_ANGLES {0,0, 0,0, 70,0} // X,Y,Z Axis Extend and Retract angles
 
+/**********************************************************************\
+ * Support for a filament diameter sensor
+ * Also allows adjustment of diameter at print time (vs  at slicing)
+ * Single extruder only at this point (extruder 0)
+ * 
+ * Motherboards
+ * 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector 
+ * 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E)
+ * 301 - Rambo  - uses Analog input 3
+ * Note may require analog pins to be defined for different motherboards
+ **********************************************************************/
+// Uncomment below to enable
+//#define FILAMENT_SENSOR
+
+#define FILAMENT_SENSOR_EXTRUDER_NUM	0  //The number of the extruder that has the filament sensor (0,1,2)
+#define MEASUREMENT_DELAY_CM			14  //measurement delay in cm.  This is the distance from filament sensor to middle of barrel
+
+#define DEFAULT_NOMINAL_FILAMENT_DIA  3.0  //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software.  Used for sensor reading validation
+#define MEASURED_UPPER_LIMIT          3.30  //upper limit factor used for sensor reading validation in mm
+#define MEASURED_LOWER_LIMIT          1.90  //lower limit factor for sensor reading validation in mm
+#define MAX_MEASUREMENT_DELAY			20  //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM  and lower number saves RAM)
+
+//defines used in the code
+#define DEFAULT_MEASURED_FILAMENT_DIA  DEFAULT_NOMINAL_FILAMENT_DIA  //set measured to nominal initially 
+
+//When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status.  Status will appear for 5 sec.
+//#define FILAMENT_LCD_DISPLAY
+
+
+
+
+
+
 #include "Configuration_adv.h"
 #include "thermistortables.h"
 

Marlin/example_configurations/makibox/Configuration_adv.h

@@ -296,6 +296,20 @@
 // using:
 //#define MENU_ADDAUTOSTART
 
+// Show a progress bar on the LCD when printing from SD
+//#define LCD_PROGRESS_BAR
+
+#ifdef LCD_PROGRESS_BAR
+  // Amount of time (ms) to show the bar
+  #define PROGRESS_BAR_BAR_TIME 2000
+  // Amount of time (ms) to show the status message
+  #define PROGRESS_BAR_MSG_TIME 2000
+  // Amount of time (ms) to retain the status message (0=forever)
+  #define PROGRESS_MSG_EXPIRE   0
+  // Enable this to show messages for MSG_TIME then hide them
+  //#define PROGRESS_MSG_ONCE
+#endif
+
 // The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
 //#define USE_WATCHDOG
 
@@ -331,7 +345,7 @@
 
 // extruder advance constant (s2/mm3)
 //
-// advance (steps) = STEPS_PER_CUBIC_MM_E * EXTUDER_ADVANCE_K * cubic mm per second ^ 2
+// advance (steps) = STEPS_PER_CUBIC_MM_E * EXTRUDER_ADVANCE_K * cubic mm per second ^ 2
 //
 // Hooke's law says:		force = k * distance
 // Bernoulli's principle says:	v ^ 2 / 2 + g . h + pressure / density = constant

Marlin/example_configurations/tvrrug/Round2/Configuration.h

@@ -749,7 +749,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
  * 
  * Motherboards
  * 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector 
- * 81 - Printrboard - Uses Analog input 2 on the Aux 2 connector
+ * 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E)
  * 301 - Rambo  - uses Analog input 3
  * Note may require analog pins to be defined for different motherboards
  **********************************************************************/
@@ -767,6 +767,8 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
 //defines used in the code
 #define DEFAULT_MEASURED_FILAMENT_DIA  DEFAULT_NOMINAL_FILAMENT_DIA  //set measured to nominal initially 
 
+//When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status.  Status will appear for 5 sec.
+//#define FILAMENT_LCD_DISPLAY
 
 
 

Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h

@@ -297,6 +297,20 @@
 // using:
 //#define MENU_ADDAUTOSTART
 
+// Show a progress bar on the LCD when printing from SD?
+//#define LCD_PROGRESS_BAR
+
+#ifdef LCD_PROGRESS_BAR
+  // Amount of time (ms) to show the bar
+  #define PROGRESS_BAR_BAR_TIME 2000
+  // Amount of time (ms) to show the status message
+  #define PROGRESS_BAR_MSG_TIME 3000
+  // Amount of time (ms) to retain the status message (0=forever)
+  #define PROGRESS_MSG_EXPIRE   0
+  // Enable this to show messages for MSG_TIME then hide them
+  //#define PROGRESS_MSG_ONCE
+#endif
+
 // The hardware watchdog should reset the microcontroller disabling all outputs, in case the firmware gets stuck and doesn't do temperature regulation.
 //#define USE_WATCHDOG
 
@@ -332,7 +346,7 @@
 
 // extruder advance constant (s2/mm3)
 //
-// advance (steps) = STEPS_PER_CUBIC_MM_E * EXTUDER_ADVANCE_K * cubic mm per second ^ 2
+// advance (steps) = STEPS_PER_CUBIC_MM_E * EXTRUDER_ADVANCE_K * cubic mm per second ^ 2
 //
 // Hooke's law says:		force = k * distance
 // Bernoulli's principle says:	v ^ 2 / 2 + g . h + pressure / density = constant

Marlin/ultralcd.cpp

@@ -19,15 +19,12 @@ int absPreheatHotendTemp;
 int absPreheatHPBTemp;
 int absPreheatFanSpeed;
 
-
 #ifdef FILAMENT_LCD_DISPLAY
-unsigned long message_millis=0;
+  unsigned long message_millis = 0;
 #endif
 
-
-
 #ifdef ULTIPANEL
-static float manual_feedrate[] = MANUAL_FEEDRATE;
+  static float manual_feedrate[] = MANUAL_FEEDRATE;
 #endif // ULTIPANEL
 
 /* !Configuration settings */
@@ -163,7 +160,7 @@ uint32_t encoderPosition;
 #if (SDCARDDETECT > 0)
 bool lcd_oldcardstatus;
 #endif
-#endif//ULTIPANEL
+#endif //ULTIPANEL
 
 menuFunc_t currentMenu = lcd_status_screen; /* function pointer to the currently active menu */
 uint32_t lcd_next_update_millis;
@@ -189,12 +186,45 @@ static void lcd_goto_menu(menuFunc_t menu, const uint32_t encoder=0, const bool
     currentMenu = menu;
     encoderPosition = encoder;
     if (feedback) lcd_quick_feedback();
+
+    // For LCD_PROGRESS_BAR re-initialize the custom characters
+    #if defined(LCD_PROGRESS_BAR) && defined(SDSUPPORT)
+      lcd_set_custom_characters(menu == lcd_status_screen);
+    #endif
   }
 }
 
 /* Main status screen. It's up to the implementation specific part to show what is needed. As this is very display dependent */
 static void lcd_status_screen()
 {
+  #if defined(LCD_PROGRESS_BAR) && defined(SDSUPPORT)
+    uint16_t mil = millis();
+    #ifndef PROGRESS_MSG_ONCE
+      if (mil > progressBarTick + PROGRESS_BAR_MSG_TIME + PROGRESS_BAR_BAR_TIME) {
+        progressBarTick = mil;
+      }
+    #endif
+    #if PROGRESS_MSG_EXPIRE > 0
+      // keep the message alive if paused, count down otherwise
+      if (messageTick > 0) {
+        if (card.isFileOpen()) {
+          if (IS_SD_PRINTING) {
+            if ((mil-messageTick) >= PROGRESS_MSG_EXPIRE) {
+              lcd_status_message[0] = '\0';
+              messageTick = 0;
+            }
+          }
+          else {
+            messageTick += LCD_UPDATE_INTERVAL;
+          }
+        }
+        else {
+          messageTick = 0;
+        }
+      }
+    #endif
+  #endif //LCD_PROGRESS_BAR
+
     if (lcd_status_update_delay)
         lcd_status_update_delay--;
     else
@@ -227,10 +257,14 @@ static void lcd_status_screen()
     if (current_click)
     {
         lcd_goto_menu(lcd_main_menu);
-        lcd_implementation_init(); // to maybe revive the LCD if static electricity killed it.
+        lcd_implementation_init( // to maybe revive the LCD if static electricity killed it.
-#ifdef FILAMENT_LCD_DISPLAY
+          #if defined(LCD_PROGRESS_BAR) && defined(SDSUPPORT)
-        message_millis=millis();  //get status message to show up for a while
+            currentMenu == lcd_status_screen
-#endif
+          #endif
+        );
+        #ifdef FILAMENT_LCD_DISPLAY
+          message_millis = millis();  // get status message to show up for a while
+        #endif
     }
 
 #ifdef ULTIPANEL_FEEDMULTIPLY
@@ -257,28 +291,22 @@ static void lcd_status_screen()
         feedmultiply += int(encoderPosition);
         encoderPosition = 0;
     }
-#endif//ULTIPANEL_FEEDMULTIPLY
+#endif //ULTIPANEL_FEEDMULTIPLY
 
     if (feedmultiply < 10)
         feedmultiply = 10;
     else if (feedmultiply > 999)
         feedmultiply = 999;
-#endif//ULTIPANEL
+#endif //ULTIPANEL
 }
 
 #ifdef ULTIPANEL
-static void lcd_return_to_status()
+
-{
+static void lcd_return_to_status() { lcd_goto_menu(lcd_status_screen, 0, false); }
-    lcd_goto_menu(lcd_status_screen, 0, false);
+
-}
+static void lcd_sdcard_pause() { card.pauseSDPrint(); }
-static void lcd_sdcard_pause()
+
-{
+static void lcd_sdcard_resume() { card.startFileprint(); }
-    card.pauseSDPrint();
-}
-static void lcd_sdcard_resume()
-{
-    card.startFileprint();
-}
 
 static void lcd_sdcard_stop()
 {
@@ -918,10 +946,8 @@ void lcd_sdcard_menu()
 #define menu_edit_type(_type, _name, _strFunc, scale) \
     void menu_edit_ ## _name () \
     { \
-        if ((int32_t)encoderPosition < 0) \
+        if ((int32_t)encoderPosition < 0) encoderPosition = 0; \
-            encoderPosition = 0; \
+        if ((int32_t)encoderPosition > maxEditValue) encoderPosition = maxEditValue; \
-        if ((int32_t)encoderPosition > maxEditValue) \
-            encoderPosition = maxEditValue; \
         if (lcdDrawUpdate) \
             lcd_implementation_drawedit(editLabel, _strFunc(((_type)((int32_t)encoderPosition + minEditValue)) / scale)); \
         if (LCD_CLICKED) \
@@ -1112,7 +1138,11 @@ void lcd_update()
     {
         lcdDrawUpdate = 2;
         lcd_oldcardstatus = IS_SD_INSERTED;
-        lcd_implementation_init(); // to maybe revive the LCD if static electricity killed it.
+        lcd_implementation_init( // to maybe revive the LCD if static electricity killed it.
+          #if defined(LCD_PROGRESS_BAR) && defined(SDSUPPORT)
+            currentMenu == lcd_status_screen
+          #endif
+        );
 
         if(lcd_oldcardstatus)
         {
@@ -1192,10 +1222,8 @@ void lcd_update()
             lcdDrawUpdate = 2;
         }
 #endif//ULTIPANEL
-        if (lcdDrawUpdate == 2)
+        if (lcdDrawUpdate == 2) lcd_implementation_clear();
-            lcd_implementation_clear();
+        if (lcdDrawUpdate) lcdDrawUpdate--;
-        if (lcdDrawUpdate)
-            lcdDrawUpdate--;
         lcd_next_update_millis = millis() + LCD_UPDATE_INTERVAL;
     }
 }
@@ -1206,35 +1234,39 @@ void lcd_ignore_click(bool b)
     wait_for_unclick = false;
 }
 
+void lcd_finishstatus() {
+  int len = strlen(lcd_status_message);
+  if (len > 0) {
+    while (len < LCD_WIDTH) {
+      lcd_status_message[len++] = ' ';
+    }
+  }
+  lcd_status_message[LCD_WIDTH] = '\0';
+  #if defined(LCD_PROGRESS_BAR) && defined(SDSUPPORT)
+    #if PROGRESS_MSG_EXPIRE > 0
+      messageTick =
+    #endif
+    progressBarTick = millis();
+  #endif
+  lcdDrawUpdate = 2;
+
+  #ifdef FILAMENT_LCD_DISPLAY
+    message_millis = millis();  //get status message to show up for a while
+  #endif
+}
 void lcd_setstatus(const char* message)
 {
     if (lcd_status_message_level > 0)
         return;
     strncpy(lcd_status_message, message, LCD_WIDTH);
-
+    lcd_finishstatus();
-    size_t i = strlen(lcd_status_message);
-    memset(lcd_status_message + i, ' ', LCD_WIDTH - i);
-    lcd_status_message[LCD_WIDTH] = '\0';
-
-    lcdDrawUpdate = 2;
-#ifdef FILAMENT_LCD_DISPLAY
-        message_millis=millis();  //get status message to show up for a while
-#endif
 }
 void lcd_setstatuspgm(const char* message)
 {
     if (lcd_status_message_level > 0)
         return;
     strncpy_P(lcd_status_message, message, LCD_WIDTH);
-
+    lcd_finishstatus();
-    size_t i = strlen(lcd_status_message);
-    memset(lcd_status_message + i, ' ', LCD_WIDTH - i);
-    lcd_status_message[LCD_WIDTH] = '\0';
-
-    lcdDrawUpdate = 2;
-#ifdef FILAMENT_LCD_DISPLAY
-        message_millis=millis();  //get status message to show up for a while
-#endif
 }
 void lcd_setalertstatuspgm(const char* message)
 {
@@ -1382,7 +1414,7 @@ char *itostr2(const uint8_t &x)
   return conv;
 }
 
-//  convert float to string with +123.4 format
+// Convert float to string with 123.4 format, dropping sign
 char *ftostr31(const float &x)
 {
   int xx=x*10;
@@ -1397,7 +1429,7 @@ char *ftostr31(const float &x)
   return conv;
 }
 
-//  convert float to string with 123.4 format
+// Convert float to string with 123.4 format
 char *ftostr31ns(const float &x)
 {
   int xx=x*10;
@@ -1429,7 +1461,7 @@ char *ftostr32(const float &x)
   return conv;
 }
 
-//Float to string with 1.23 format
+// Convert float to string with 1.23 format
 char *ftostr12ns(const float &x)
 {
   long xx=x*100;
@@ -1443,6 +1475,7 @@ char *ftostr12ns(const float &x)
   return conv;
 }
 
+// Convert int to lj string with +123.0 format
 char *itostr31(const int &xx)
 {
   conv[0]=(xx>=0)?'+':'-';
@@ -1475,6 +1508,7 @@ char *itostr3(const int &x)
   return conv;
 }
 
+// Convert int to lj string with 123 format
 char *itostr3left(const int &xx)
 {
   if (xx >= 100)
@@ -1508,7 +1542,7 @@ char *itostr4(const int &xx) {
   return conv;
 }
 
-//  convert float to rj string with 12345 format
+// Convert float to rj string with 12345 format
 char *ftostr5(const float &x) {
   long xx = abs(x);
   conv[0] = xx >= 10000 ? (xx / 10000) % 10 + '0' : ' ';
@@ -1520,7 +1554,7 @@ char *ftostr5(const float &x) {
   return conv;
 }
 
-//  convert float to string with +1234.5 format
+// Convert float to string with +1234.5 format
 char *ftostr51(const float &x)
 {
   long xx=x*10;
@@ -1536,7 +1570,7 @@ char *ftostr51(const float &x)
   return conv;
 }
 
-//  convert float to string with +123.45 format
+// Convert float to string with +123.45 format
 char *ftostr52(const float &x)
 {
   long xx=x*100;

Marlin/ultralcd_implementation_hitachi_HD44780.h

@@ -208,6 +208,14 @@ extern volatile uint16_t buttons;  //an extended version of the last checked but
   LCD_CLASS lcd(LCD_PINS_RS, LCD_PINS_ENABLE, LCD_PINS_D4, LCD_PINS_D5,LCD_PINS_D6,LCD_PINS_D7);  //RS,Enable,D4,D5,D6,D7
 #endif
 
+#if defined(LCD_PROGRESS_BAR) && defined(SDSUPPORT)
+  static uint16_t progressBarTick = 0;
+  #if PROGRESS_MSG_EXPIRE > 0
+    static uint16_t messageTick = 0;
+  #endif
+  #define LCD_STR_PROGRESS  "\x03\x04\x05"
+#endif
+
 /* Custom characters defined in the first 8 characters of the LCD */
 #define LCD_STR_BEDTEMP     "\x00"
 #define LCD_STR_DEGREE      "\x01"
@@ -219,10 +227,12 @@ extern volatile uint16_t buttons;  //an extended version of the last checked but
 #define LCD_STR_CLOCK       "\x07"
 #define LCD_STR_ARROW_RIGHT "\x7E"  /* from the default character set */
 
-static void lcd_implementation_init()
+static void lcd_set_custom_characters(
-{
+  #if defined(LCD_PROGRESS_BAR) && defined(SDSUPPORT)
-    byte bedTemp[8] =
+    bool progress_bar_set=true
-    {
+  #endif
+) {
+  byte bedTemp[8] = {
     B00000,
     B11111,
     B10101,
@@ -232,8 +242,7 @@ static void lcd_implementation_init()
     B00000,
     B00000
   }; //thanks Sonny Mounicou
-    byte degree[8] =
+  byte degree[8] = {
-    {
     B01100,
     B10010,
     B10010,
@@ -243,8 +252,7 @@ static void lcd_implementation_init()
     B00000,
     B00000
   };
-    byte thermometer[8] =
+  byte thermometer[8] = {
-    {
     B00100,
     B01010,
     B01010,
@@ -254,7 +262,7 @@ static void lcd_implementation_init()
     B10001,
     B01110
   };
-    byte uplevel[8]={
+  byte uplevel[8] = {
     B00100,
     B01110,
     B11111,
@@ -264,7 +272,7 @@ static void lcd_implementation_init()
     B00000,
     B00000
   }; //thanks joris
-    byte refresh[8]={
+  byte refresh[8] = {
     B00000,
     B00110,
     B11001,
@@ -274,7 +282,7 @@ static void lcd_implementation_init()
     B01100,
     B00000,
   }; //thanks joris
-    byte folder [8]={
+  byte folder[8] = {
     B00000,
     B11100,
     B11111,
@@ -284,7 +292,7 @@ static void lcd_implementation_init()
     B00000,
     B00000
   }; //thanks joris
-    byte feedrate [8]={
+  byte feedrate[8] = {
     B11100,
     B10000,
     B11000,
@@ -294,7 +302,7 @@ static void lcd_implementation_init()
     B00101,
     B00000
   }; //thanks Sonny Mounicou
-    byte clock [8]={
+  byte clock[8] = {
     B00000,
     B01110,
     B10011,
@@ -305,6 +313,72 @@ static void lcd_implementation_init()
     B00000
   }; //thanks Sonny Mounicou
 
+  #if defined(LCD_PROGRESS_BAR) && defined(SDSUPPORT)
+    static bool char_mode = false;
+    byte progress[3][8] = { {
+      B00000,
+      B10000,
+      B10000,
+      B10000,
+      B10000,
+      B10000,
+      B10000,
+      B00000
+    }, {
+      B00000,
+      B10100,
+      B10100,
+      B10100,
+      B10100,
+      B10100,
+      B10100,
+      B00000
+    }, {
+      B00000,
+      B10101,
+      B10101,
+      B10101,
+      B10101,
+      B10101,
+      B10101,
+      B00000
+    } };
+    if (progress_bar_set != char_mode) {
+      char_mode = progress_bar_set;
+      lcd.createChar(LCD_STR_BEDTEMP[0], bedTemp);
+      lcd.createChar(LCD_STR_DEGREE[0], degree);
+      lcd.createChar(LCD_STR_THERMOMETER[0], thermometer);
+      lcd.createChar(LCD_STR_FEEDRATE[0], feedrate);
+      lcd.createChar(LCD_STR_CLOCK[0], clock);
+      if (progress_bar_set) {
+        // Progress bar characters for info screen
+        for (int i=3; i--;) lcd.createChar(LCD_STR_PROGRESS[i], progress[i]);
+      }
+      else {
+        // Custom characters for submenus
+        lcd.createChar(LCD_STR_UPLEVEL[0], uplevel);
+        lcd.createChar(LCD_STR_REFRESH[0], refresh);
+        lcd.createChar(LCD_STR_FOLDER[0], folder);
+      }
+    }
+  #else
+    lcd.createChar(LCD_STR_BEDTEMP[0], bedTemp);
+    lcd.createChar(LCD_STR_DEGREE[0], degree);
+    lcd.createChar(LCD_STR_THERMOMETER[0], thermometer);
+    lcd.createChar(LCD_STR_UPLEVEL[0], uplevel);
+    lcd.createChar(LCD_STR_REFRESH[0], refresh);
+    lcd.createChar(LCD_STR_FOLDER[0], folder);
+    lcd.createChar(LCD_STR_FEEDRATE[0], feedrate);
+    lcd.createChar(LCD_STR_CLOCK[0], clock);
+  #endif
+}
+
+static void lcd_implementation_init(
+  #if defined(LCD_PROGRESS_BAR) && defined(SDSUPPORT)
+    bool progress_bar_set=true
+  #endif
+) {
+
 #if defined(LCD_I2C_TYPE_PCF8575)
     lcd.begin(LCD_WIDTH, LCD_HEIGHT);
   #ifdef LCD_I2C_PIN_BL
@@ -329,14 +403,12 @@ static void lcd_implementation_init()
     lcd.begin(LCD_WIDTH, LCD_HEIGHT);
 #endif
 
-    lcd.createChar(LCD_STR_BEDTEMP[0], bedTemp);
+    lcd_set_custom_characters(
-    lcd.createChar(LCD_STR_DEGREE[0], degree);
+        #if defined(LCD_PROGRESS_BAR) && defined(SDSUPPORT)
-    lcd.createChar(LCD_STR_THERMOMETER[0], thermometer);
+            progress_bar_set
-    lcd.createChar(LCD_STR_UPLEVEL[0], uplevel);
+        #endif
-    lcd.createChar(LCD_STR_REFRESH[0], refresh);
+    );
-    lcd.createChar(LCD_STR_FOLDER[0], folder);
+
-    lcd.createChar(LCD_STR_FEEDRATE[0], feedrate);
-    lcd.createChar(LCD_STR_CLOCK[0], clock);
     lcd.clear();
 }
 static void lcd_implementation_clear()
@@ -507,23 +579,46 @@ static void lcd_implementation_status_screen()
     }
 #endif
 
+  // Status message line at the bottom
+  lcd.setCursor(0, LCD_HEIGHT - 1);
+
+  #if defined(LCD_PROGRESS_BAR) && defined(SDSUPPORT)
+
+    if (card.isFileOpen()) {
+      uint16_t mil = millis(), diff = mil - progressBarTick;
+      if (diff >= PROGRESS_BAR_MSG_TIME || !lcd_status_message[0]) {
+        // draw the progress bar
+        int tix = (int)(card.percentDone() * LCD_WIDTH * 3) / 100,
+          cel = tix / 3, rem = tix % 3, i = LCD_WIDTH;
+        char msg[LCD_WIDTH+1], b = ' ';
+        msg[i] = '\0';
+        while (i--) {
+          if (i == cel - 1)
+            b = LCD_STR_PROGRESS[2];
+          else if (i == cel && rem != 0)
+            b = LCD_STR_PROGRESS[rem-1];
+          msg[i] = b;
+        }
+        lcd.print(msg);
+        return;
+      }
+    } //card.isFileOpen
+
+  #endif //LCD_PROGRESS_BAR
+
   //Display both Status message line and Filament display on the last line
   #ifdef FILAMENT_LCD_DISPLAY
-      if(message_millis+5000>millis()){  //display any status for the first 5 sec after screen is initiated
+    if (message_millis + 5000 <= millis()) {  //display any status for the first 5 sec after screen is initiated
-         	 lcd.setCursor(0, LCD_HEIGHT - 1);
-        	 lcd.print(lcd_status_message);
-        } else {
-		     lcd.setCursor(0,LCD_HEIGHT - 1);
       lcd_printPGM(PSTR("Dia "));
       lcd.print(ftostr12ns(filament_width_meas));
       lcd_printPGM(PSTR(" V"));
       lcd.print(itostr3(100.0*volumetric_multiplier[FILAMENT_SENSOR_EXTRUDER_NUM]));
   	  lcd.print('%');
+  	  return;
     }
-    #else
+  #endif //FILAMENT_LCD_DISPLAY
-    lcd.setCursor(0, LCD_HEIGHT - 1);
+
   lcd.print(lcd_status_message);
-    #endif
 }
 static void lcd_implementation_drawmenu_generic(uint8_t row, const char* pstr, char pre_char, char post_char)
 {