diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
index 16d0bfa317..4c08bd0dee 100644
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@@ -1413,7 +1413,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h
index 965f45e256..69ffe00d14 100644
--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@@ -1002,7 +1002,7 @@
   #if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING)
     #define DOUBLECLICK_MAX_INTERVAL 1250   // Maximum interval between clicks, in milliseconds.
                                             // Note: Extra time may be added to mitigate controller latency.
-    //#define BABYSTEP_ALWAYS_AVAILABLE     // Allow babystepping at all times (not just during movement).
+    #define BABYSTEP_ALWAYS_AVAILABLE     // Allow babystepping at all times (not just during movement).
     //#define MOVE_Z_WHEN_IDLE              // Jump to the move Z menu on doubleclick when printer is idle.
     #if ENABLED(MOVE_Z_WHEN_IDLE)
       #define MOVE_Z_IDLE_MULTIPLICATOR 1   // Multiply 1mm by this factor for the move step size.
diff --git a/config/default/Configuration.h b/config/default/Configuration.h
index 16d0bfa317..4c08bd0dee 100644
--- a/config/default/Configuration.h
+++ b/config/default/Configuration.h
@@ -1413,7 +1413,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/3DFabXYZ/Migbot/Configuration.h b/config/examples/3DFabXYZ/Migbot/Configuration.h
index 2a7bf9b8d2..8f245bba1c 100644
--- a/config/examples/3DFabXYZ/Migbot/Configuration.h
+++ b/config/examples/3DFabXYZ/Migbot/Configuration.h
@@ -1444,7 +1444,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/AlephObjects/TAZ4/Configuration.h b/config/examples/AlephObjects/TAZ4/Configuration.h
index 7db2f6399c..02951d05b5 100644
--- a/config/examples/AlephObjects/TAZ4/Configuration.h
+++ b/config/examples/AlephObjects/TAZ4/Configuration.h
@@ -1433,7 +1433,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/AliExpress/CL-260/Configuration.h b/config/examples/AliExpress/CL-260/Configuration.h
index 60c7948169..15721f9543 100644
--- a/config/examples/AliExpress/CL-260/Configuration.h
+++ b/config/examples/AliExpress/CL-260/Configuration.h
@@ -1413,7 +1413,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/AliExpress/UM2pExt/Configuration.h b/config/examples/AliExpress/UM2pExt/Configuration.h
index 96f7ba5bd3..8cccbe28bb 100644
--- a/config/examples/AliExpress/UM2pExt/Configuration.h
+++ b/config/examples/AliExpress/UM2pExt/Configuration.h
@@ -1424,7 +1424,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Anet/A2/Configuration.h b/config/examples/Anet/A2/Configuration.h
index 7f5c349429..f47f7e760c 100644
--- a/config/examples/Anet/A2/Configuration.h
+++ b/config/examples/Anet/A2/Configuration.h
@@ -1413,7 +1413,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Anet/A2plus/Configuration.h b/config/examples/Anet/A2plus/Configuration.h
index 1349858378..2f9d983aab 100644
--- a/config/examples/Anet/A2plus/Configuration.h
+++ b/config/examples/Anet/A2plus/Configuration.h
@@ -1413,7 +1413,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Anet/A6/Configuration.h b/config/examples/Anet/A6/Configuration.h
index 81569f6177..409cb16d6c 100644
--- a/config/examples/Anet/A6/Configuration.h
+++ b/config/examples/Anet/A6/Configuration.h
@@ -1565,7 +1565,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Anet/A8/Configuration.h b/config/examples/Anet/A8/Configuration.h
index 47b828ce4c..654894e696 100644
--- a/config/examples/Anet/A8/Configuration.h
+++ b/config/examples/Anet/A8/Configuration.h
@@ -1426,7 +1426,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/AnyCubic/i3/Configuration.h b/config/examples/AnyCubic/i3/Configuration.h
index d4c6e0e01c..fde6030f5b 100644
--- a/config/examples/AnyCubic/i3/Configuration.h
+++ b/config/examples/AnyCubic/i3/Configuration.h
@@ -1423,7 +1423,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/ArmEd/Configuration.h b/config/examples/ArmEd/Configuration.h
index 70c54296f3..6fb7a69038 100644
--- a/config/examples/ArmEd/Configuration.h
+++ b/config/examples/ArmEd/Configuration.h
@@ -1414,7 +1414,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Azteeg/X5GT/Configuration.h b/config/examples/Azteeg/X5GT/Configuration.h
index fc93873ed5..fc7d69ef7b 100644
--- a/config/examples/Azteeg/X5GT/Configuration.h
+++ b/config/examples/Azteeg/X5GT/Configuration.h
@@ -1413,7 +1413,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/BIBO/TouchX/cyclops/Configuration.h b/config/examples/BIBO/TouchX/cyclops/Configuration.h
index b44d388496..ff5d52c227 100644
--- a/config/examples/BIBO/TouchX/cyclops/Configuration.h
+++ b/config/examples/BIBO/TouchX/cyclops/Configuration.h
@@ -1413,7 +1413,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/BIBO/TouchX/default/Configuration.h b/config/examples/BIBO/TouchX/default/Configuration.h
index d338ca8a52..b4d5b8692e 100644
--- a/config/examples/BIBO/TouchX/default/Configuration.h
+++ b/config/examples/BIBO/TouchX/default/Configuration.h
@@ -1413,7 +1413,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/BQ/Hephestos/Configuration.h b/config/examples/BQ/Hephestos/Configuration.h
index f75ed2fcf6..2682dc8d8d 100644
--- a/config/examples/BQ/Hephestos/Configuration.h
+++ b/config/examples/BQ/Hephestos/Configuration.h
@@ -1401,7 +1401,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/BQ/Hephestos_2/Configuration.h b/config/examples/BQ/Hephestos_2/Configuration.h
index 2f2594e99a..3a212e615d 100644
--- a/config/examples/BQ/Hephestos_2/Configuration.h
+++ b/config/examples/BQ/Hephestos_2/Configuration.h
@@ -1413,7 +1413,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 10 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/BQ/WITBOX/Configuration.h b/config/examples/BQ/WITBOX/Configuration.h
index c89413b5c5..cd4743adcf 100644
--- a/config/examples/BQ/WITBOX/Configuration.h
+++ b/config/examples/BQ/WITBOX/Configuration.h
@@ -1401,7 +1401,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Cartesio/Configuration.h b/config/examples/Cartesio/Configuration.h
index 74fa02b18b..8495900a28 100644
--- a/config/examples/Cartesio/Configuration.h
+++ b/config/examples/Cartesio/Configuration.h
@@ -1412,7 +1412,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Creality/CR-10/Configuration.h b/config/examples/Creality/CR-10/Configuration.h
index 0b881bcde7..7e80a736dd 100644
--- a/config/examples/Creality/CR-10/Configuration.h
+++ b/config/examples/Creality/CR-10/Configuration.h
@@ -1423,7 +1423,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Creality/CR-10S/Configuration.h b/config/examples/Creality/CR-10S/Configuration.h
index b372077e92..dd77607105 100644
--- a/config/examples/Creality/CR-10S/Configuration.h
+++ b/config/examples/Creality/CR-10S/Configuration.h
@@ -1414,7 +1414,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 3), (Y_MAX_POS - 3), 10 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Creality/CR-10_5S/Configuration.h b/config/examples/Creality/CR-10_5S/Configuration.h
index 17d0f49d8a..c4decff149 100644
--- a/config/examples/Creality/CR-10_5S/Configuration.h
+++ b/config/examples/Creality/CR-10_5S/Configuration.h
@@ -1416,7 +1416,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 20), (Y_MAX_POS - 20), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Creality/CR-10mini/Configuration.h b/config/examples/Creality/CR-10mini/Configuration.h
index ee693f30b9..8ed2585cbf 100644
--- a/config/examples/Creality/CR-10mini/Configuration.h
+++ b/config/examples/Creality/CR-10mini/Configuration.h
@@ -1432,7 +1432,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Creality/CR-8/Configuration.h b/config/examples/Creality/CR-8/Configuration.h
index 6285715af9..80786293b8 100644
--- a/config/examples/Creality/CR-8/Configuration.h
+++ b/config/examples/Creality/CR-8/Configuration.h
@@ -1423,7 +1423,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Creality/Ender-2/Configuration.h b/config/examples/Creality/Ender-2/Configuration.h
index 8e07221354..4a2100f748 100644
--- a/config/examples/Creality/Ender-2/Configuration.h
+++ b/config/examples/Creality/Ender-2/Configuration.h
@@ -1417,7 +1417,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Creality/Ender-3/Configuration.h b/config/examples/Creality/Ender-3/Configuration.h
index ebf1455c9d..4830d11e8c 100644
--- a/config/examples/Creality/Ender-3/Configuration.h
+++ b/config/examples/Creality/Ender-3/Configuration.h
@@ -1417,7 +1417,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Creality/Ender-4/Configuration.h b/config/examples/Creality/Ender-4/Configuration.h
index af5f71e93a..80065812eb 100644
--- a/config/examples/Creality/Ender-4/Configuration.h
+++ b/config/examples/Creality/Ender-4/Configuration.h
@@ -1423,7 +1423,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Einstart-S/Configuration.h b/config/examples/Einstart-S/Configuration.h
index fd1a179761..95a65f3455 100644
--- a/config/examples/Einstart-S/Configuration.h
+++ b/config/examples/Einstart-S/Configuration.h
@@ -1423,7 +1423,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Felix/Configuration.h b/config/examples/Felix/Configuration.h
index 3d951698f8..bb483970dc 100644
--- a/config/examples/Felix/Configuration.h
+++ b/config/examples/Felix/Configuration.h
@@ -1395,7 +1395,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Felix/DUAL/Configuration.h b/config/examples/Felix/DUAL/Configuration.h
index 841da015db..ca570006e4 100644
--- a/config/examples/Felix/DUAL/Configuration.h
+++ b/config/examples/Felix/DUAL/Configuration.h
@@ -1395,7 +1395,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/FlashForge/CreatorPro/Configuration.h b/config/examples/FlashForge/CreatorPro/Configuration.h
index a267439e7b..1339812f1b 100644
--- a/config/examples/FlashForge/CreatorPro/Configuration.h
+++ b/config/examples/FlashForge/CreatorPro/Configuration.h
@@ -1404,7 +1404,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MAX_POS - 2), (Y_MAX_POS - 2), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/FolgerTech/i3-2020/Configuration.h b/config/examples/FolgerTech/i3-2020/Configuration.h
index ec04f97539..7046bdbef1 100644
--- a/config/examples/FolgerTech/i3-2020/Configuration.h
+++ b/config/examples/FolgerTech/i3-2020/Configuration.h
@@ -1419,7 +1419,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Formbot/Raptor/Configuration.h b/config/examples/Formbot/Raptor/Configuration.h
index a127789604..a902afaaa2 100644
--- a/config/examples/Formbot/Raptor/Configuration.h
+++ b/config/examples/Formbot/Raptor/Configuration.h
@@ -1518,7 +1518,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { 10, 10, 20}
   #define NOZZLE_PARK_XY_FEEDRATE 70    // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Formbot/T_Rex_2+/Configuration.h b/config/examples/Formbot/T_Rex_2+/Configuration.h
index 451e352560..0723675876 100644
--- a/config/examples/Formbot/T_Rex_2+/Configuration.h
+++ b/config/examples/Formbot/T_Rex_2+/Configuration.h
@@ -1448,7 +1448,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { 50, (Y_MIN_POS + 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Formbot/T_Rex_3/Configuration.h b/config/examples/Formbot/T_Rex_3/Configuration.h
index 6935056e8e..fd3659ccd7 100644
--- a/config/examples/Formbot/T_Rex_3/Configuration.h
+++ b/config/examples/Formbot/T_Rex_3/Configuration.h
@@ -1438,7 +1438,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { 100, (Y_MIN_POS + 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Geeetech/A10M/Configuration.h b/config/examples/Geeetech/A10M/Configuration.h
index f8be81c5e4..3af04731e4 100644
--- a/config/examples/Geeetech/A10M/Configuration.h
+++ b/config/examples/Geeetech/A10M/Configuration.h
@@ -1398,7 +1398,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { 3, 3, 10 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Geeetech/A20M/Configuration.h b/config/examples/Geeetech/A20M/Configuration.h
index 8d52093c09..2c1a94f52b 100644
--- a/config/examples/Geeetech/A20M/Configuration.h
+++ b/config/examples/Geeetech/A20M/Configuration.h
@@ -1398,7 +1398,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { 3, 3, 10 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Geeetech/GT2560/Configuration.h b/config/examples/Geeetech/GT2560/Configuration.h
index d5c52b694c..df757b999d 100644
--- a/config/examples/Geeetech/GT2560/Configuration.h
+++ b/config/examples/Geeetech/GT2560/Configuration.h
@@ -1428,7 +1428,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h b/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h
index bb7f3c6180..0ffab861ea 100644
--- a/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h
+++ b/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h
@@ -1402,7 +1402,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Geeetech/MeCreator2/Configuration.h b/config/examples/Geeetech/MeCreator2/Configuration.h
index 9a7d4c7048..2aaf3036c8 100644
--- a/config/examples/Geeetech/MeCreator2/Configuration.h
+++ b/config/examples/Geeetech/MeCreator2/Configuration.h
@@ -1420,7 +1420,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h
index ee0e8166d9..2937e710d3 100644
--- a/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h	
+++ b/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h	
@@ -1429,7 +1429,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h
index 12f48870e7..bf8025d542 100644
--- a/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h	
+++ b/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h	
@@ -1428,7 +1428,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h
index 5698c217de..a4f4e5c8dc 100644
--- a/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h	
+++ b/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h	
@@ -1413,7 +1413,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h
index 79ea413150..0f2f47216a 100644
--- a/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h	
+++ b/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h	
@@ -1413,7 +1413,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Infitary/i3-M508/Configuration.h b/config/examples/Infitary/i3-M508/Configuration.h
index 2d25e6afe7..d7b1e3e2e7 100644
--- a/config/examples/Infitary/i3-M508/Configuration.h
+++ b/config/examples/Infitary/i3-M508/Configuration.h
@@ -1417,7 +1417,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/JGAurora/A5/Configuration.h b/config/examples/JGAurora/A5/Configuration.h
index 686a90d9db..836d51485e 100644
--- a/config/examples/JGAurora/A5/Configuration.h
+++ b/config/examples/JGAurora/A5/Configuration.h
@@ -1425,7 +1425,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/MakerParts/Configuration.h b/config/examples/MakerParts/Configuration.h
index ec81d59d02..081d840058 100644
--- a/config/examples/MakerParts/Configuration.h
+++ b/config/examples/MakerParts/Configuration.h
@@ -1433,7 +1433,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Malyan/M150/Configuration.h b/config/examples/Malyan/M150/Configuration.h
index f4e390a9f5..91d85f1721 100644
--- a/config/examples/Malyan/M150/Configuration.h
+++ b/config/examples/Malyan/M150/Configuration.h
@@ -1441,7 +1441,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Malyan/M200/Configuration.h b/config/examples/Malyan/M200/Configuration.h
index 7ef45d7370..e173d8ca8a 100644
--- a/config/examples/Malyan/M200/Configuration.h
+++ b/config/examples/Malyan/M200/Configuration.h
@@ -1412,7 +1412,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Micromake/C1/basic/Configuration.h b/config/examples/Micromake/C1/basic/Configuration.h
index 165c59b6cd..f82b7b7586 100644
--- a/config/examples/Micromake/C1/basic/Configuration.h
+++ b/config/examples/Micromake/C1/basic/Configuration.h
@@ -1417,7 +1417,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Micromake/C1/enhanced/Configuration.h b/config/examples/Micromake/C1/enhanced/Configuration.h
index ebc346557c..3d2cc19fbd 100644
--- a/config/examples/Micromake/C1/enhanced/Configuration.h
+++ b/config/examples/Micromake/C1/enhanced/Configuration.h
@@ -1417,7 +1417,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Mks/Robin/Configuration.h b/config/examples/Mks/Robin/Configuration.h
index badacbb6da..9fd998c98a 100644
--- a/config/examples/Mks/Robin/Configuration.h
+++ b/config/examples/Mks/Robin/Configuration.h
@@ -1414,7 +1414,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Mks/Sbase/Configuration.h b/config/examples/Mks/Sbase/Configuration.h
index 18dc3f9d63..eebb5b6e83 100644
--- a/config/examples/Mks/Sbase/Configuration.h
+++ b/config/examples/Mks/Sbase/Configuration.h
@@ -1413,7 +1413,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Printrbot/PrintrboardG2/Configuration.h b/config/examples/Printrbot/PrintrboardG2/Configuration.h
index 0c2b1cd67d..7f99022fef 100644
--- a/config/examples/Printrbot/PrintrboardG2/Configuration.h
+++ b/config/examples/Printrbot/PrintrboardG2/Configuration.h
@@ -1421,7 +1421,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/RapideLite/RL200/Configuration.h b/config/examples/RapideLite/RL200/Configuration.h
index b1940d723f..b2c38bac91 100644
--- a/config/examples/RapideLite/RL200/Configuration.h
+++ b/config/examples/RapideLite/RL200/Configuration.h
@@ -1413,7 +1413,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/RepRapPro/Huxley/Configuration.h b/config/examples/RepRapPro/Huxley/Configuration.h
index 9e8b5c55f4..4f5ce094cf 100644
--- a/config/examples/RepRapPro/Huxley/Configuration.h
+++ b/config/examples/RepRapPro/Huxley/Configuration.h
@@ -1462,7 +1462,7 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100                        // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE DEFAULT_MAX_Z_FEEDRATE      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/RepRapWorld/Megatronics/Configuration.h b/config/examples/RepRapWorld/Megatronics/Configuration.h
index 4b6cd06abe..5e31ae7c4d 100644
--- a/config/examples/RepRapWorld/Megatronics/Configuration.h
+++ b/config/examples/RepRapWorld/Megatronics/Configuration.h
@@ -1413,7 +1413,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/RigidBot/Configuration.h b/config/examples/RigidBot/Configuration.h
index 27c9471f75..40c9e135d5 100644
--- a/config/examples/RigidBot/Configuration.h
+++ b/config/examples/RigidBot/Configuration.h
@@ -1411,7 +1411,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/SCARA/Configuration.h b/config/examples/SCARA/Configuration.h
index 8b5284655a..cb34fa9b26 100644
--- a/config/examples/SCARA/Configuration.h
+++ b/config/examples/SCARA/Configuration.h
@@ -1426,7 +1426,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/STM32/Black_STM32F407VET6/Configuration.h b/config/examples/STM32/Black_STM32F407VET6/Configuration.h
index a1b425e406..f31615cf08 100644
--- a/config/examples/STM32/Black_STM32F407VET6/Configuration.h
+++ b/config/examples/STM32/Black_STM32F407VET6/Configuration.h
@@ -1413,7 +1413,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/STM32/STM32F10/Configuration.h b/config/examples/STM32/STM32F10/Configuration.h
index da9b22431c..345d5960c7 100644
--- a/config/examples/STM32/STM32F10/Configuration.h
+++ b/config/examples/STM32/STM32F10/Configuration.h
@@ -1415,7 +1415,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/STM32/stm32f103ret6/Configuration.h b/config/examples/STM32/stm32f103ret6/Configuration.h
index 31aee8c6ea..673f87ecb9 100644
--- a/config/examples/STM32/stm32f103ret6/Configuration.h
+++ b/config/examples/STM32/stm32f103ret6/Configuration.h
@@ -1415,7 +1415,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Sanguinololu/Configuration.h b/config/examples/Sanguinololu/Configuration.h
index 5382da453c..3a07899a4d 100644
--- a/config/examples/Sanguinololu/Configuration.h
+++ b/config/examples/Sanguinololu/Configuration.h
@@ -1444,7 +1444,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/TheBorg/Configuration.h b/config/examples/TheBorg/Configuration.h
index 787d2dad6d..bf803f0a4e 100644
--- a/config/examples/TheBorg/Configuration.h
+++ b/config/examples/TheBorg/Configuration.h
@@ -1413,7 +1413,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/TinyBoy2/Configuration.h b/config/examples/TinyBoy2/Configuration.h
index f4ddd1d5a2..8ccbae5274 100644
--- a/config/examples/TinyBoy2/Configuration.h
+++ b/config/examples/TinyBoy2/Configuration.h
@@ -1469,7 +1469,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Tronxy/X1/Configuration.h b/config/examples/Tronxy/X1/Configuration.h
index 22489b6ba4..5708b5a922 100644
--- a/config/examples/Tronxy/X1/Configuration.h
+++ b/config/examples/Tronxy/X1/Configuration.h
@@ -1413,7 +1413,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Tronxy/X3A/Configuration.h b/config/examples/Tronxy/X3A/Configuration.h
index c20bac923d..f7ee64c0e2 100644
--- a/config/examples/Tronxy/X3A/Configuration.h
+++ b/config/examples/Tronxy/X3A/Configuration.h
@@ -1417,7 +1417,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Tronxy/X5S-2E/Configuration.h b/config/examples/Tronxy/X5S-2E/Configuration.h
index b57f799750..7ed78d62c3 100644
--- a/config/examples/Tronxy/X5S-2E/Configuration.h
+++ b/config/examples/Tronxy/X5S-2E/Configuration.h
@@ -1434,7 +1434,7 @@
 #define NOZZLE_PARK_FEATURE P2
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Tronxy/X5S/Configuration.h b/config/examples/Tronxy/X5S/Configuration.h
index c93f4d158b..db146107be 100644
--- a/config/examples/Tronxy/X5S/Configuration.h
+++ b/config/examples/Tronxy/X5S/Configuration.h
@@ -1412,7 +1412,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Tronxy/XY100/Configuration.h b/config/examples/Tronxy/XY100/Configuration.h
index a68dd5fb62..2756982f44 100644
--- a/config/examples/Tronxy/XY100/Configuration.h
+++ b/config/examples/Tronxy/XY100/Configuration.h
@@ -1424,7 +1424,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/UltiMachine/Archim1/Configuration.h b/config/examples/UltiMachine/Archim1/Configuration.h
index 15696b31b2..f9620d365d 100644
--- a/config/examples/UltiMachine/Archim1/Configuration.h
+++ b/config/examples/UltiMachine/Archim1/Configuration.h
@@ -1413,7 +1413,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/UltiMachine/Archim2/Configuration.h b/config/examples/UltiMachine/Archim2/Configuration.h
index 8425c5006d..d7e0552162 100644
--- a/config/examples/UltiMachine/Archim2/Configuration.h
+++ b/config/examples/UltiMachine/Archim2/Configuration.h
@@ -1413,7 +1413,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/VORONDesign/Configuration.h b/config/examples/VORONDesign/Configuration.h
index 422eb1827c..41f07aff3b 100644
--- a/config/examples/VORONDesign/Configuration.h
+++ b/config/examples/VORONDesign/Configuration.h
@@ -1422,7 +1422,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Velleman/K8200/Configuration.h b/config/examples/Velleman/K8200/Configuration.h
index 6b7b5cc486..3d0405b40e 100644
--- a/config/examples/Velleman/K8200/Configuration.h
+++ b/config/examples/Velleman/K8200/Configuration.h
@@ -1443,7 +1443,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Velleman/K8400/Configuration.h b/config/examples/Velleman/K8400/Configuration.h
index 81e6768dee..4dc1e11c49 100644
--- a/config/examples/Velleman/K8400/Configuration.h
+++ b/config/examples/Velleman/K8400/Configuration.h
@@ -1413,7 +1413,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Velleman/K8400/Dual-head/Configuration.h b/config/examples/Velleman/K8400/Dual-head/Configuration.h
index d0807339ab..81396a32cf 100644
--- a/config/examples/Velleman/K8400/Dual-head/Configuration.h
+++ b/config/examples/Velleman/K8400/Dual-head/Configuration.h
@@ -1413,7 +1413,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/WASP/PowerWASP/Configuration.h b/config/examples/WASP/PowerWASP/Configuration.h
index c2b841855b..901582d324 100644
--- a/config/examples/WASP/PowerWASP/Configuration.h
+++ b/config/examples/WASP/PowerWASP/Configuration.h
@@ -1432,7 +1432,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 190 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 10     // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/Wanhao/Duplicator 6/Configuration.h b/config/examples/Wanhao/Duplicator 6/Configuration.h
index e554ec3e39..2493105932 100644
--- a/config/examples/Wanhao/Duplicator 6/Configuration.h	
+++ b/config/examples/Wanhao/Duplicator 6/Configuration.h	
@@ -1423,7 +1423,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/adafruit/ST7565/Configuration.h b/config/examples/adafruit/ST7565/Configuration.h
index 80b8869006..153bac48f1 100644
--- a/config/examples/adafruit/ST7565/Configuration.h
+++ b/config/examples/adafruit/ST7565/Configuration.h
@@ -1413,7 +1413,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/delta/Anycubic/Kossel/Configuration.h b/config/examples/delta/Anycubic/Kossel/Configuration.h
index 737c761033..c0580cceb7 100644
--- a/config/examples/delta/Anycubic/Kossel/Configuration.h
+++ b/config/examples/delta/Anycubic/Kossel/Configuration.h
@@ -1603,7 +1603,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { 0, 0, 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 100    // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/delta/FLSUN/auto_calibrate/Configuration.h b/config/examples/delta/FLSUN/auto_calibrate/Configuration.h
index 3f75b1402c..2addb67e01 100644
--- a/config/examples/delta/FLSUN/auto_calibrate/Configuration.h
+++ b/config/examples/delta/FLSUN/auto_calibrate/Configuration.h
@@ -1541,7 +1541,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), 0, 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/delta/FLSUN/kossel/Configuration.h b/config/examples/delta/FLSUN/kossel/Configuration.h
index 7025ce4713..e062062b99 100644
--- a/config/examples/delta/FLSUN/kossel/Configuration.h
+++ b/config/examples/delta/FLSUN/kossel/Configuration.h
@@ -1540,7 +1540,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), 0, 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/delta/FLSUN/kossel_mini/Configuration.h b/config/examples/delta/FLSUN/kossel_mini/Configuration.h
index e3827449c8..40eebbb335 100644
--- a/config/examples/delta/FLSUN/kossel_mini/Configuration.h
+++ b/config/examples/delta/FLSUN/kossel_mini/Configuration.h
@@ -1540,7 +1540,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), 0, 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/delta/Geeetech/Rostock 301/Configuration.h b/config/examples/delta/Geeetech/Rostock 301/Configuration.h
index f21c3fd166..f3b4a7a1f6 100644
--- a/config/examples/delta/Geeetech/Rostock 301/Configuration.h	
+++ b/config/examples/delta/Geeetech/Rostock 301/Configuration.h	
@@ -1531,7 +1531,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), 0, 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/delta/Hatchbox_Alpha/Configuration.h b/config/examples/delta/Hatchbox_Alpha/Configuration.h
index 50aad9eb03..5f60b5cb7f 100644
--- a/config/examples/delta/Hatchbox_Alpha/Configuration.h
+++ b/config/examples/delta/Hatchbox_Alpha/Configuration.h
@@ -1543,7 +1543,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), 0, 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/delta/MKS/SBASE/Configuration.h b/config/examples/delta/MKS/SBASE/Configuration.h
index 95799fca54..c260380142 100644
--- a/config/examples/delta/MKS/SBASE/Configuration.h
+++ b/config/examples/delta/MKS/SBASE/Configuration.h
@@ -1528,7 +1528,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/delta/Tevo Little Monster/Configuration.h b/config/examples/delta/Tevo Little Monster/Configuration.h
index 582edf9827..49c8f2fbbe 100644
--- a/config/examples/delta/Tevo Little Monster/Configuration.h	
+++ b/config/examples/delta/Tevo Little Monster/Configuration.h	
@@ -1521,7 +1521,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { 0, 0, (DELTA_HEIGHT - 10) }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/delta/generic/Configuration.h b/config/examples/delta/generic/Configuration.h
index 8fa8b70bd9..ecdf04bedc 100644
--- a/config/examples/delta/generic/Configuration.h
+++ b/config/examples/delta/generic/Configuration.h
@@ -1528,7 +1528,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), 0, 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/delta/kossel_mini/Configuration.h b/config/examples/delta/kossel_mini/Configuration.h
index 0557aaaa69..8d43eb746b 100644
--- a/config/examples/delta/kossel_mini/Configuration.h
+++ b/config/examples/delta/kossel_mini/Configuration.h
@@ -1530,7 +1530,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), 0, 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/delta/kossel_pro/Configuration.h b/config/examples/delta/kossel_pro/Configuration.h
index bca0466b60..5386d442a0 100644
--- a/config/examples/delta/kossel_pro/Configuration.h
+++ b/config/examples/delta/kossel_pro/Configuration.h
@@ -1531,7 +1531,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), 0, 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/delta/kossel_xl/Configuration.h b/config/examples/delta/kossel_xl/Configuration.h
index c048463a68..f74113b0d4 100644
--- a/config/examples/delta/kossel_xl/Configuration.h
+++ b/config/examples/delta/kossel_xl/Configuration.h
@@ -1531,7 +1531,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), 0, 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/gCreate/gMax1.5+/Configuration.h b/config/examples/gCreate/gMax1.5+/Configuration.h
index 09a0d35cc6..e3a8de0383 100644
--- a/config/examples/gCreate/gMax1.5+/Configuration.h
+++ b/config/examples/gCreate/gMax1.5+/Configuration.h
@@ -1416,7 +1416,7 @@
 #define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/makibox/Configuration.h b/config/examples/makibox/Configuration.h
index 71671c8c4e..c5cf855c16 100644
--- a/config/examples/makibox/Configuration.h
+++ b/config/examples/makibox/Configuration.h
@@ -1416,7 +1416,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/stm32/STM32F4/Configuration.h b/config/examples/stm32/STM32F4/Configuration.h
index 8979f40fce..6b10c9a013 100644
--- a/config/examples/stm32/STM32F4/Configuration.h
+++ b/config/examples/stm32/STM32F4/Configuration.h
@@ -1413,7 +1413,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/tvrrug/Round2/Configuration.h b/config/examples/tvrrug/Round2/Configuration.h
index 9ef926d87c..7444faed05 100644
--- a/config/examples/tvrrug/Round2/Configuration.h
+++ b/config/examples/tvrrug/Round2/Configuration.h
@@ -1408,7 +1408,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
diff --git a/config/examples/wt150/Configuration.h b/config/examples/wt150/Configuration.h
index 306c1b5b5f..22b7aa4989 100644
--- a/config/examples/wt150/Configuration.h
+++ b/config/examples/wt150/Configuration.h
@@ -1418,7 +1418,7 @@
 //#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
-  // Specify a park position as { X, Y, Z }
+  // Specify a park position as { X, Y, Z_raise }
   #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
   #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)