Improve opt_set (etc.) used for tests
This commit is contained in:
Scott Lahteine
parent
0afa4cc957
commit
369ffe518d
|
|
@ -7,7 +7,7 @@ SED=$(which gsed || which sed)
|
|||
|
||||
for opt in "$@" ; do
|
||||
# Logic for returning nonzero based on answer here: https://stackoverflow.com/a/15966279/104648
|
||||
eval "${SED} -i '/\(\/\/\)*[[:blank:]]*\(#define \b${opt}\b\)/{s//\2/;h};\${x;/./{x;q0};x;q9}' Marlin/Configuration.h" ||
|
||||
eval "${SED} -i '/\(\/\/\)*[[:blank:]]*\(#define \b${opt}\b\)/{s//\2/;h};\${x;/./{x;q0};x;q9}' Marlin/Configuration_adv.h" ||
|
||||
eval "${SED} -i '/^[[:blank:]]*\(\/\/\)*[[:blank:]]*\(#define \b${opt}\b\)/{s//\2/;h};\${x;/./{x;q0};x;q9}' Marlin/Configuration.h" ||
|
||||
eval "${SED} -i '/^[[:blank:]]*\(\/\/\)*[[:blank:]]*\(#define \b${opt}\b\)/{s//\2/;h};\${x;/./{x;q0};x;q9}' Marlin/Configuration_adv.h" ||
|
||||
(echo "ERROR: opt_enable Can't find ${opt}" >&2 && exit 9)
|
||||
done
|
||||
|
|
|
|||
|
|
@ -5,8 +5,12 @@ set -e
|
|||
|
||||
SED=$(which gsed || which sed)
|
||||
|
||||
# Logic for returning nonzero based on answer here: https://stackoverflow.com/a/15966279/104648
|
||||
eval "${SED} -i '/\(\/\/\)*\([[:blank:]]*\)\(#define\s\+\b${1}\b\).*$/{s//\2\3 ${2}/;h};\${x;/./{x;q0};x;q9}' Marlin/Configuration.h" ||
|
||||
eval "${SED} -i '/\(\/\/\)*\([[:blank:]]*\)\(#define\s\+\b${1}\b\).*$/{s//\2\3 ${2}/;h};\${x;/./{x;q0};x;q9}' Marlin/Configuration_adv.h" ||
|
||||
eval "echo '#define ${@}' >>Marlin/Configuration_adv.h" ||
|
||||
(echo "ERROR: opt_set Can't set or add ${1}" >&2 && exit 9)
|
||||
ARGC=$#
|
||||
while [[ $# > 1 ]]; do
|
||||
# Logic for returning nonzero based on answer here: https://stackoverflow.com/a/15966279/104648
|
||||
eval "${SED} -i '/^[[:blank:]]*\(\/\/\)*\([[:blank:]]*\)\(#define\s\+\b${1}\b\).*$/{s//\2\3 ${2}/;h};\${x;/./{x;q0};x;q9}' Marlin/Configuration.h" ||
|
||||
eval "${SED} -i '/^[[:blank:]]*\(\/\/\)*\([[:blank:]]*\)\(#define\s\+\b${1}\b\).*$/{s//\2\3 ${2}/;h};\${x;/./{x;q0};x;q9}' Marlin/Configuration_adv.h" ||
|
||||
eval "echo '#define ${1} ${2}' >>Marlin/Configuration.h" ||
|
||||
(echo "ERROR: opt_set Can't set or add ${1}" >&2 && exit 9)
|
||||
shift 2
|
||||
done
|
||||
|
|
|
|||
|
|
@ -7,5 +7,5 @@ PIN=$2
|
|||
VAL=$3
|
||||
|
||||
SED=$(which gsed || which sed)
|
||||
eval "${SED} -i '/\(\/\/\)*\(#define \+${PIN}\b\).*$/{s//\2 ${VAL}/;h};\${x;/./{x;q0};x;q9}' Marlin/src/pins/$DIR/pins_${NAM}.h" ||
|
||||
eval "${SED} -i '/^[[:blank:]]*\(\/\/\)*[[:blank:]]*\(#define \+${PIN}\b\).*$/{s//\2 ${VAL}/;h};\${x;/./{x;q0};x;q9}' Marlin/src/pins/$DIR/pins_${NAM}.h" ||
|
||||
(echo "ERROR: pins_set Can't find ${PIN}" >&2 && exit 9)
|
||||
|
|
|
|||
|
|
@ -11,8 +11,7 @@ set -e
|
|||
#
|
||||
restore_configs
|
||||
use_example_configs ArmEd
|
||||
opt_set X_DRIVER_TYPE TMC2130
|
||||
opt_set Y_DRIVER_TYPE TMC2208
|
||||
opt_set X_DRIVER_TYPE TMC2130 Y_DRIVER_TYPE TMC2208
|
||||
exec_test $1 $2 "ArmEd Example Configuration with mixed TMC Drivers" "$3"
|
||||
|
||||
# clean up
|
||||
|
|
|
|||
|
|
@ -10,10 +10,10 @@ set -e
|
|||
# Build with the default configurations
|
||||
#
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_BTT_BTT002_V1_0
|
||||
opt_set SERIAL_PORT 1
|
||||
opt_set X_DRIVER_TYPE TMC2209
|
||||
opt_set Y_DRIVER_TYPE TMC2130
|
||||
opt_set MOTHERBOARD BOARD_BTT_BTT002_V1_0 \
|
||||
SERIAL_PORT 1 \
|
||||
X_DRIVER_TYPE TMC2209 \
|
||||
Y_DRIVER_TYPE TMC2130
|
||||
exec_test $1 $2 "BigTreeTech BTT002 Default Configuration plus TMC steppers" "$3"
|
||||
|
||||
# clean up
|
||||
|
|
|
|||
|
|
@ -7,54 +7,24 @@
|
|||
set -e
|
||||
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_BTT_GTR_V1_0
|
||||
opt_set SERIAL_PORT -1
|
||||
opt_set EXTRUDERS 8
|
||||
opt_set TEMP_SENSOR_1 1
|
||||
opt_set TEMP_SENSOR_2 1
|
||||
opt_set TEMP_SENSOR_3 1
|
||||
opt_set TEMP_SENSOR_4 1
|
||||
opt_set TEMP_SENSOR_5 1
|
||||
opt_set TEMP_SENSOR_6 1
|
||||
opt_set TEMP_SENSOR_7 1
|
||||
opt_set MOTHERBOARD BOARD_BTT_GTR_V1_0 SERIAL_PORT -1 \
|
||||
EXTRUDERS 8 TEMP_SENSOR_1 1 TEMP_SENSOR_2 1 TEMP_SENSOR_3 1 TEMP_SENSOR_4 1 TEMP_SENSOR_5 1 TEMP_SENSOR_6 1 TEMP_SENSOR_7 1
|
||||
# Not necessary to enable auto-fan for all extruders to hit problematic code paths
|
||||
opt_set E0_AUTO_FAN_PIN PC10
|
||||
opt_set E1_AUTO_FAN_PIN PC11
|
||||
opt_set E2_AUTO_FAN_PIN PC12
|
||||
opt_set X_DRIVER_TYPE TMC2208
|
||||
opt_set Y_DRIVER_TYPE TMC2130
|
||||
opt_set NEOPIXEL_PIN PF13
|
||||
opt_enable REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER BLTOUCH NEOPIXEL_LED Z_SAFE_HOMING
|
||||
opt_enable FILAMENT_RUNOUT_SENSOR NOZZLE_PARK_FEATURE ADVANCED_PAUSE_FEATURE
|
||||
opt_set FIL_RUNOUT_PIN 3
|
||||
opt_set FIL_RUNOUT2_PIN 4
|
||||
opt_set FIL_RUNOUT3_PIN 5
|
||||
opt_set FIL_RUNOUT4_PIN 6
|
||||
opt_set FIL_RUNOUT5_PIN 7
|
||||
opt_set FIL_RUNOUT6_PIN 8
|
||||
opt_set FIL_RUNOUT7_PIN 9
|
||||
opt_set FIL_RUNOUT8_PIN 10
|
||||
opt_set FIL_RUNOUT4_STATE HIGH
|
||||
opt_enable FIL_RUNOUT4_PULLUP
|
||||
opt_set FIL_RUNOUT8_STATE HIGH
|
||||
opt_enable FIL_RUNOUT8_PULLUP
|
||||
exec_test $1 $2 "BigTreeTech GTR 8 Extruders with Auto-Fan, Mixed TMC Drivers, and Runout Sensors with distinct states" "$3"
|
||||
opt_set E0_AUTO_FAN_PIN PC10 E1_AUTO_FAN_PIN PC11 E2_AUTO_FAN_PIN PC12 NEOPIXEL_PIN PF13 \
|
||||
X_DRIVER_TYPE TMC2208 Y_DRIVER_TYPE TMC2130 \
|
||||
FIL_RUNOUT_PIN 3 FIL_RUNOUT2_PIN 4 FIL_RUNOUT3_PIN 5 FIL_RUNOUT4_PIN 6 FIL_RUNOUT5_PIN 7 FIL_RUNOUT6_PIN 8 FIL_RUNOUT7_PIN 9 FIL_RUNOUT8_PIN 10 \
|
||||
FIL_RUNOUT4_STATE HIGH FIL_RUNOUT8_STATE HIGH
|
||||
opt_enable REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER BLTOUCH NEOPIXEL_LED Z_SAFE_HOMING NOZZLE_PARK_FEATURE ADVANCED_PAUSE_FEATURE \
|
||||
FILAMENT_RUNOUT_SENSOR FIL_RUNOUT4_PULLUP FIL_RUNOUT8_PULLUP
|
||||
exec_test $1 $2 "BigTreeTech GTR | 8 Extruders | Auto-Fan | Mixed TMC Drivers | Runout Sensors w/ distinct states" "$3"
|
||||
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_BTT_GTR_V1_0
|
||||
opt_set SERIAL_PORT -1
|
||||
opt_set EXTRUDERS 6
|
||||
opt_set TEMP_SENSOR_1 1
|
||||
opt_set TEMP_SENSOR_2 1
|
||||
opt_set TEMP_SENSOR_3 1
|
||||
opt_set TEMP_SENSOR_4 1
|
||||
opt_set TEMP_SENSOR_5 1
|
||||
opt_set NUM_Z_STEPPER_DRIVERS 3
|
||||
opt_set DEFAULT_Kp_LIST "{ 22.2, 20.0, 21.0, 19.0, 18.0, 17.0 }"
|
||||
opt_set DEFAULT_Ki_LIST "{ 1.08 }"
|
||||
opt_set DEFAULT_Kd_LIST "{ 114.0, 112.0, 110.0, 108.0 }"
|
||||
opt_set MOTHERBOARD BOARD_BTT_GTR_V1_0 SERIAL_PORT -1 \
|
||||
EXTRUDERS 6 TEMP_SENSOR_1 1 TEMP_SENSOR_2 1 TEMP_SENSOR_3 1 TEMP_SENSOR_4 1 TEMP_SENSOR_5 1 \
|
||||
NUM_Z_STEPPER_DRIVERS 3 \
|
||||
DEFAULT_Kp_LIST '{ 22.2, 20.0, 21.0, 19.0, 18.0, 17.0 }' DEFAULT_Ki_LIST '{ 1.08 }' DEFAULT_Kd_LIST '{ 114.0, 112.0, 110.0, 108.0 }'
|
||||
opt_enable TOOLCHANGE_FILAMENT_SWAP TOOLCHANGE_MIGRATION_FEATURE TOOLCHANGE_FS_INIT_BEFORE_SWAP TOOLCHANGE_FS_PRIME_FIRST_USED PID_PARAMS_PER_HOTEND
|
||||
exec_test $1 $2 "BigTreeTech GTR 6 Extruders Triple Z" "$3"
|
||||
exec_test $1 $2 "BigTreeTech GTR | 6 Extruders | Triple Z" "$3"
|
||||
|
||||
# clean up
|
||||
restore_configs
|
||||
|
|
|
|||
|
|
@ -7,41 +7,18 @@
|
|||
set -e
|
||||
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_BTT_GTR_V1_0
|
||||
opt_set SERIAL_PORT 3
|
||||
opt_set EXTRUDERS 8
|
||||
opt_set TEMP_SENSOR_1 1
|
||||
opt_set TEMP_SENSOR_2 1
|
||||
opt_set TEMP_SENSOR_3 1
|
||||
opt_set TEMP_SENSOR_4 1
|
||||
opt_set TEMP_SENSOR_5 1
|
||||
opt_set TEMP_SENSOR_6 1
|
||||
opt_set TEMP_SENSOR_7 1
|
||||
opt_set SDSUPPORT
|
||||
opt_set USB_FLASH_DRIVE_SUPPORT
|
||||
opt_set USE_OTG_USB_HOST
|
||||
opt_set MOTHERBOARD BOARD_BTT_GTR_V1_0 SERIAL_PORT 3 \
|
||||
EXTRUDERS 8 TEMP_SENSOR_1 1 TEMP_SENSOR_2 1 TEMP_SENSOR_3 1 TEMP_SENSOR_4 1 TEMP_SENSOR_5 1 TEMP_SENSOR_6 1 TEMP_SENSOR_7 1
|
||||
opt_enable SDSUPPORT USB_FLASH_DRIVE_SUPPORT USE_OTG_USB_HOST \
|
||||
REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER BLTOUCH NEOPIXEL_LED Z_SAFE_HOMING \
|
||||
FILAMENT_RUNOUT_SENSOR NOZZLE_PARK_FEATURE ADVANCED_PAUSE_FEATURE
|
||||
# Not necessary to enable auto-fan for all extruders to hit problematic code paths
|
||||
opt_set E0_AUTO_FAN_PIN PC10
|
||||
opt_set E1_AUTO_FAN_PIN PC11
|
||||
opt_set E2_AUTO_FAN_PIN PC12
|
||||
opt_set X_DRIVER_TYPE TMC2208
|
||||
opt_set Y_DRIVER_TYPE TMC2130
|
||||
opt_set NEOPIXEL_PIN PF13
|
||||
opt_enable REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER BLTOUCH NEOPIXEL_LED Z_SAFE_HOMING
|
||||
opt_enable FILAMENT_RUNOUT_SENSOR NOZZLE_PARK_FEATURE ADVANCED_PAUSE_FEATURE
|
||||
opt_set FIL_RUNOUT_PIN 3
|
||||
opt_set FIL_RUNOUT2_PIN 4
|
||||
opt_set FIL_RUNOUT3_PIN 5
|
||||
opt_set FIL_RUNOUT4_PIN 6
|
||||
opt_set FIL_RUNOUT5_PIN 7
|
||||
opt_set FIL_RUNOUT6_PIN 8
|
||||
opt_set FIL_RUNOUT7_PIN 9
|
||||
opt_set FIL_RUNOUT8_PIN 10
|
||||
opt_set FIL_RUNOUT4_STATE HIGH
|
||||
opt_enable FIL_RUNOUT4_PULLUP
|
||||
opt_set FIL_RUNOUT8_STATE HIGH
|
||||
opt_enable FIL_RUNOUT8_PULLUP
|
||||
exec_test $1 $2 "BigTreeTech GTR + OTG USB Flash Drive + Extruders with Auto-Fan, Mixed TMC Drivers, and Runout Sensors with distinct states" "$3"
|
||||
opt_set E0_AUTO_FAN_PIN PC10 E1_AUTO_FAN_PIN PC11 E2_AUTO_FAN_PIN PC12 NEOPIXEL_PIN PF13 \
|
||||
X_DRIVER_TYPE TMC2208 Y_DRIVER_TYPE TMC2130 \
|
||||
FIL_RUNOUT_PIN 3 FIL_RUNOUT2_PIN 4 FIL_RUNOUT3_PIN 5 FIL_RUNOUT4_PIN 6 FIL_RUNOUT5_PIN 7 FIL_RUNOUT6_PIN 8 FIL_RUNOUT7_PIN 9 FIL_RUNOUT8_PIN 10 \
|
||||
FIL_RUNOUT4_STATE HIGH FIL_RUNOUT8_STATE HIGH
|
||||
opt_enable FIL_RUNOUT4_PULLUP FIL_RUNOUT8_PULLUP
|
||||
exec_test $1 $2 "GTT GTR | OTG USB Flash Drive | 8 Extruders | Auto-Fan | Mixed TMC Drivers | Runout Sensors (distinct)" "$3"
|
||||
|
||||
# clean up
|
||||
restore_configs
|
||||
|
|
|
|||
|
|
@ -10,31 +10,22 @@ set -e
|
|||
# Build with the default configurations
|
||||
#
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_BTT_SKR_PRO_V1_1
|
||||
opt_set SERIAL_PORT 1
|
||||
opt_set MOTHERBOARD BOARD_BTT_SKR_PRO_V1_1 SERIAL_PORT 1
|
||||
exec_test $1 $2 "BigTreeTech SKR Pro Default Configuration" "$3"
|
||||
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_BTT_SKR_PRO_V1_1
|
||||
opt_set SERIAL_PORT -1
|
||||
opt_set EXTRUDERS 3
|
||||
opt_set TEMP_SENSOR_1 1
|
||||
opt_set TEMP_SENSOR_2 1
|
||||
opt_set E0_AUTO_FAN_PIN PC10
|
||||
opt_set E1_AUTO_FAN_PIN PC11
|
||||
opt_set E2_AUTO_FAN_PIN PC12
|
||||
opt_set X_DRIVER_TYPE TMC2209
|
||||
opt_set Y_DRIVER_TYPE TMC2130
|
||||
opt_set MOTHERBOARD BOARD_BTT_SKR_PRO_V1_1 SERIAL_PORT -1 \
|
||||
EXTRUDERS 3 TEMP_SENSOR_1 1 TEMP_SENSOR_2 1 \
|
||||
E0_AUTO_FAN_PIN PC10 E1_AUTO_FAN_PIN PC11 E2_AUTO_FAN_PIN PC12 \
|
||||
X_DRIVER_TYPE TMC2209 Y_DRIVER_TYPE TMC2130
|
||||
opt_enable BLTOUCH EEPROM_SETTINGS AUTO_BED_LEVELING_3POINT Z_SAFE_HOMING PINS_DEBUGGING
|
||||
exec_test $1 $2 "BigTreeTech SKR Pro 3 Extruders, Auto-Fan, BLTOUCH, mixed TMC drivers" "$3"
|
||||
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_BTT_SKR_PRO_V1_1
|
||||
opt_set SERIAL_PORT -1
|
||||
opt_set MOTHERBOARD BOARD_BTT_SKR_PRO_V1_1 SERIAL_PORT -1 \
|
||||
CUTTER_POWER_UNIT PERCENT \
|
||||
SPINDLE_LASER_PWM_PIN HEATER_1_PIN SPINDLE_LASER_ENA_PIN HEATER_2_PIN
|
||||
opt_enable LASER_FEATURE REPRAP_DISCOUNT_SMART_CONTROLLER
|
||||
opt_set CUTTER_POWER_UNIT PERCENT
|
||||
opt_add SPINDLE_LASER_PWM_PIN HEATER_1_PIN
|
||||
opt_add SPINDLE_LASER_ENA_PIN HEATER_2_PIN
|
||||
exec_test $1 $2 "Laser, LCD, PERCENT power unit" "$3"
|
||||
|
||||
# clean up
|
||||
|
|
|
|||
|
|
@ -7,12 +7,12 @@
|
|||
set -e
|
||||
|
||||
restore_configs
|
||||
opt_set LCD_LANGUAGE bg
|
||||
opt_set MOTHERBOARD BOARD_RAMPS4DUE_EFB
|
||||
opt_set TEMP_SENSOR_0 -2
|
||||
opt_set TEMP_SENSOR_BED 2
|
||||
opt_set GRID_MAX_POINTS_X 16
|
||||
opt_set FANMUX0_PIN 53
|
||||
opt_set MOTHERBOARD BOARD_RAMPS4DUE_EFB \
|
||||
LCD_LANGUAGE bg \
|
||||
TEMP_SENSOR_0 -2 TEMP_SENSOR_BED 2 \
|
||||
GRID_MAX_POINTS_X 16 \
|
||||
E0_AUTO_FAN_PIN 8 FANMUX0_PIN 53 EXTRUDER_AUTO_FAN_SPEED 100 \
|
||||
TEMP_SENSOR_CHAMBER 3 TEMP_CHAMBER_PIN 6 HEATER_CHAMBER_PIN 45
|
||||
opt_enable S_CURVE_ACCELERATION EEPROM_SETTINGS GCODE_MACROS \
|
||||
FIX_MOUNTED_PROBE Z_SAFE_HOMING CODEPENDENT_XY_HOMING \
|
||||
ASSISTED_TRAMMING ASSISTED_TRAMMING_WIZARD REPORT_TRAMMING_MM ASSISTED_TRAMMING_WAIT_POSITION \
|
||||
|
|
@ -29,22 +29,16 @@ opt_enable S_CURVE_ACCELERATION EEPROM_SETTINGS GCODE_MACROS \
|
|||
PINS_DEBUGGING MAX7219_DEBUG M114_DETAIL \
|
||||
EXTENSIBLE_UI
|
||||
opt_add EXTUI_EXAMPLE
|
||||
opt_set E0_AUTO_FAN_PIN 8
|
||||
opt_set EXTRUDER_AUTO_FAN_SPEED 100
|
||||
opt_set TEMP_SENSOR_CHAMBER 3
|
||||
opt_add TEMP_CHAMBER_PIN 6
|
||||
opt_set HEATER_CHAMBER_PIN 45
|
||||
exec_test $1 $2 "RAMPS4DUE_EFB with ABL (Bilinear), ExtUI, S-Curve, many options." "$3"
|
||||
|
||||
#
|
||||
# RADDS with BLTouch, ABL(B), 3 x Z auto-align
|
||||
#
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_RADDS
|
||||
opt_set MOTHERBOARD BOARD_RADDS NUM_Z_STEPPER_DRIVERS 3
|
||||
opt_enable USE_XMAX_PLUG USE_YMAX_PLUG ENDSTOPPULLUPS BLTOUCH AUTO_BED_LEVELING_BILINEAR \
|
||||
Z_STEPPER_AUTO_ALIGN Z_STEPPER_ALIGN_KNOWN_STEPPER_POSITIONS Z_SAFE_HOMING
|
||||
#TOUCH_UI_FTDI_EVE LCD_ALEPHOBJECTS_CLCD_UI OTHER_PIN_LAYOUT
|
||||
opt_set NUM_Z_STEPPER_DRIVERS 3
|
||||
pins_set ramps/RAMPS X_MAX_PIN -1
|
||||
pins_set ramps/RAMPS Y_MAX_PIN -1
|
||||
exec_test $1 $2 "RADDS with ABL (Bilinear), Triple Z Axis, Z_STEPPER_AUTO_ALIGN" "$3"
|
||||
|
|
@ -53,9 +47,6 @@ exec_test $1 $2 "RADDS with ABL (Bilinear), Triple Z Axis, Z_STEPPER_AUTO_ALIGN"
|
|||
# Test SWITCHING_EXTRUDER
|
||||
#
|
||||
restore_configs
|
||||
opt_set LCD_LANGUAGE fi
|
||||
opt_set MOTHERBOARD BOARD_RAMPS4DUE_EEF
|
||||
opt_set EXTRUDERS 2
|
||||
opt_set NUM_SERVOS 1
|
||||
opt_set MOTHERBOARD BOARD_RAMPS4DUE_EEF LCD_LANGUAGE fi EXTRUDERS 2 NUM_SERVOS 1
|
||||
opt_enable SWITCHING_EXTRUDER ULTIMAKERCONTROLLER BEEP_ON_FEEDRATE_CHANGE POWER_LOSS_RECOVERY
|
||||
exec_test $1 $2 "RAMPS4DUE_EEF with SWITCHING_EXTRUDER, POWER_LOSS_RECOVERY" "$3"
|
||||
|
|
|
|||
|
|
@ -8,10 +8,7 @@ set -e
|
|||
|
||||
# Build examples
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_FLYF407ZG
|
||||
opt_set SERIAL_PORT -1
|
||||
opt_set X_DRIVER_TYPE TMC2208
|
||||
opt_set Y_DRIVER_TYPE TMC2130
|
||||
opt_set MOTHERBOARD BOARD_FLYF407ZG SERIAL_PORT -1 X_DRIVER_TYPE TMC2208 Y_DRIVER_TYPE TMC2130
|
||||
exec_test $1 $2 "FLYF407ZG Default Config with mixed TMC Drivers" "$3"
|
||||
|
||||
# cleanup
|
||||
|
|
|
|||
|
|
@ -18,34 +18,24 @@ exec_test $1 $2 "FYSETC F6 1.3 with DGUS" "$3"
|
|||
# Delta Config (generic) + UBL + ALLEN_KEY + EEPROM_SETTINGS + OLED_PANEL_TINYBOY2
|
||||
#
|
||||
use_example_configs delta/generic
|
||||
opt_set MOTHERBOARD BOARD_FYSETC_F6_13
|
||||
opt_set MOTHERBOARD BOARD_FYSETC_F6_13 \
|
||||
LCD_LANGUAGE ko_KR \
|
||||
X_DRIVER_TYPE L6470 Y_DRIVER_TYPE L6470 Z_DRIVER_TYPE L6470 \
|
||||
L6470_CHAIN_SCK_PIN 53 L6470_CHAIN_MISO_PIN 49 L6470_CHAIN_MOSI_PIN 40 L6470_CHAIN_SS_PIN 42 \
|
||||
'ENABLE_RESET_L64XX_CHIPS(V)' NOOP
|
||||
opt_enable RESTORE_LEVELING_AFTER_G28 EEPROM_SETTINGS EEPROM_CHITCHAT \
|
||||
Z_PROBE_ALLEN_KEY AUTO_BED_LEVELING_UBL \
|
||||
OLED_PANEL_TINYBOY2 MESH_EDIT_GFX_OVERLAY DELTA_CALIBRATION_MENU
|
||||
opt_set LCD_LANGUAGE ko_KR
|
||||
opt_set X_DRIVER_TYPE L6470
|
||||
opt_set Y_DRIVER_TYPE L6470
|
||||
opt_set Z_DRIVER_TYPE L6470
|
||||
opt_add L6470_CHAIN_SCK_PIN 53
|
||||
opt_add L6470_CHAIN_MISO_PIN 49
|
||||
opt_add L6470_CHAIN_MOSI_PIN 40
|
||||
opt_add L6470_CHAIN_SS_PIN 42
|
||||
opt_add "ENABLE_RESET_L64XX_CHIPS(V) NOOP"
|
||||
exec_test $1 $2 "DELTA, RAMPS, L6470, UBL, Allen Key, EEPROM, OLED_PANEL_TINYBOY2..." "$3"
|
||||
|
||||
#
|
||||
# Test mixed TMC config
|
||||
#
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_FYSETC_F6_13
|
||||
opt_set LCD_LANGUAGE vi
|
||||
opt_set LCD_LANGUAGE_2 fr
|
||||
opt_set X_DRIVER_TYPE TMC2160
|
||||
opt_set Y_DRIVER_TYPE TMC5160
|
||||
opt_set Z_DRIVER_TYPE TMC2208_STANDALONE
|
||||
opt_set E0_DRIVER_TYPE TMC2130
|
||||
opt_set X_MIN_ENDSTOP_INVERTING true
|
||||
opt_set Y_MIN_ENDSTOP_INVERTING true
|
||||
opt_set MOTHERBOARD BOARD_FYSETC_F6_13 \
|
||||
LCD_LANGUAGE vi LCD_LANGUAGE_2 fr \
|
||||
X_DRIVER_TYPE TMC2160 Y_DRIVER_TYPE TMC5160 Z_DRIVER_TYPE TMC2208_STANDALONE E0_DRIVER_TYPE TMC2130 \
|
||||
X_MIN_ENDSTOP_INVERTING true Y_MIN_ENDSTOP_INVERTING true
|
||||
opt_enable REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER \
|
||||
MARLIN_BRICKOUT MARLIN_INVADERS MARLIN_SNAKE \
|
||||
MONITOR_DRIVER_STATUS STEALTHCHOP_XY STEALTHCHOP_Z STEALTHCHOP_E HYBRID_THRESHOLD \
|
||||
|
|
@ -63,17 +53,14 @@ exec_test $1 $2 "RAMPS 1.3 | DELTA | FLSUN AC Config" "$3"
|
|||
# SCARA with Mixed TMC
|
||||
#
|
||||
use_example_configs SCARA/Morgan
|
||||
opt_set MOTHERBOARD BOARD_FYSETC_F6_13
|
||||
opt_set LCD_LANGUAGE es
|
||||
opt_set MOTHERBOARD BOARD_FYSETC_F6_13 \
|
||||
LCD_LANGUAGE es \
|
||||
X_MAX_ENDSTOP_INVERTING false \
|
||||
X_DRIVER_TYPE TMC2209 Y_DRIVER_TYPE TMC2130 Z_DRIVER_TYPE TMC2130_STANDALONE E0_DRIVER_TYPE TMC2660 \
|
||||
X_HARDWARE_SERIAL Serial2
|
||||
opt_enable USE_ZMIN_PLUG FIX_MOUNTED_PROBE AUTO_BED_LEVELING_BILINEAR PAUSE_BEFORE_DEPLOY_STOW \
|
||||
FYSETC_242_OLED_12864 EEPROM_SETTINGS EEPROM_CHITCHAT M114_DETAIL Z_SAFE_HOMING \
|
||||
STEALTHCHOP_XY STEALTHCHOP_Z STEALTHCHOP_E HYBRID_THRESHOLD SENSORLESS_HOMING SQUARE_WAVE_STEPPING
|
||||
opt_set X_MAX_ENDSTOP_INVERTING false
|
||||
opt_set X_DRIVER_TYPE TMC2209
|
||||
opt_set Y_DRIVER_TYPE TMC2130
|
||||
opt_set Z_DRIVER_TYPE TMC2130_STANDALONE
|
||||
opt_set E0_DRIVER_TYPE TMC2660
|
||||
opt_add X_HARDWARE_SERIAL Serial2
|
||||
exec_test $1 $2 "FYSETC_F6 | SCARA | Mixed TMC | EEPROM" "$3"
|
||||
|
||||
# clean up
|
||||
|
|
|
|||
|
|
@ -10,8 +10,7 @@ set -e
|
|||
restore_configs
|
||||
use_example_configs FYSETC/S6
|
||||
opt_enable MEATPACK
|
||||
opt_set Y_DRIVER_TYPE TMC2209
|
||||
opt_set Z_DRIVER_TYPE TMC2130
|
||||
opt_set Y_DRIVER_TYPE TMC2209 Z_DRIVER_TYPE TMC2130
|
||||
exec_test $1 $2 "FYSETC S6 Example" "$3"
|
||||
|
||||
# cleanup
|
||||
|
|
|
|||
|
|
@ -10,8 +10,7 @@ set -e
|
|||
# Build with the default configurations
|
||||
#
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_LERDGE_X
|
||||
opt_set SERIAL_PORT 1
|
||||
opt_set MOTHERBOARD BOARD_LERDGE_X SERIAL_PORT 1
|
||||
exec_test $1 $2 "LERDGE X with Default Configuration" "$3"
|
||||
|
||||
# clean up
|
||||
|
|
|
|||
|
|
@ -14,9 +14,8 @@ set -e
|
|||
#exec_test $1 $2 "Default Configuration" "$3"
|
||||
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_RAMPS_14_RE_ARM_EFB
|
||||
opt_set MOTHERBOARD BOARD_RAMPS_14_RE_ARM_EFB NEOPIXEL_PIN P1_16
|
||||
opt_enable VIKI2 SDSUPPORT SDCARD_READONLY SERIAL_PORT_2 NEOPIXEL_LED
|
||||
opt_set NEOPIXEL_PIN P1_16
|
||||
exec_test $1 $2 "ReARM EFB VIKI2, SDSUPPORT, 2 Serial ports (USB CDC + UART0), NeoPixel" "$3"
|
||||
|
||||
#restore_configs
|
||||
|
|
@ -24,19 +23,18 @@ exec_test $1 $2 "ReARM EFB VIKI2, SDSUPPORT, 2 Serial ports (USB CDC + UART0), N
|
|||
#exec_test $1 $2 "MKS SBASE Example Config" "$3"
|
||||
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_MKS_SBASE
|
||||
opt_set EXTRUDERS 2
|
||||
opt_set TEMP_SENSOR_1 1
|
||||
opt_set NUM_SERVOS 2
|
||||
opt_set SERVO_DELAY "{ 300, 300 }"
|
||||
opt_set MOTHERBOARD BOARD_MKS_SBASE \
|
||||
EXTRUDERS 2 TEMP_SENSOR_1 1 \
|
||||
NUM_SERVOS 2 SERVO_DELAY '{ 300, 300 }'
|
||||
opt_enable SWITCHING_NOZZLE SWITCHING_NOZZLE_E1_SERVO_NR ULTIMAKERCONTROLLER
|
||||
exec_test $1 $2 "MKS SBASE with SWITCHING_NOZZLE" "$3"
|
||||
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_RAMPS_14_RE_ARM_EEB
|
||||
opt_set EXTRUDERS 2
|
||||
opt_set TEMP_SENSOR_1 -1
|
||||
opt_set TEMP_SENSOR_BED 5
|
||||
opt_set MOTHERBOARD BOARD_RAMPS_14_RE_ARM_EEB \
|
||||
EXTRUDERS 2 TEMP_SENSOR_1 -1 TEMP_SENSOR_BED 5 \
|
||||
GRID_MAX_POINTS_X 16 \
|
||||
NOZZLE_TO_PROBE_OFFSET '{ 0, 0, 0 }' \
|
||||
NOZZLE_CLEAN_MIN_TEMP 170
|
||||
opt_enable REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER ADAPTIVE_FAN_SLOWING NO_FAN_SLOWING_IN_PID_TUNING \
|
||||
FILAMENT_WIDTH_SENSOR FILAMENT_LCD_DISPLAY PID_EXTRUSION_SCALING SOUND_MENU_ITEM \
|
||||
NOZZLE_AS_PROBE AUTO_BED_LEVELING_BILINEAR PREHEAT_BEFORE_LEVELING G29_RETRY_AND_RECOVER Z_MIN_PROBE_REPEATABILITY_TEST DEBUG_LEVELING_FEATURE \
|
||||
|
|
@ -46,9 +44,6 @@ opt_enable REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER ADAPTIVE_FAN_SLOWING NO
|
|||
HOST_KEEPALIVE_FEATURE HOST_ACTION_COMMANDS HOST_PROMPT_SUPPORT \
|
||||
LCD_INFO_MENU ARC_SUPPORT BEZIER_CURVE_SUPPORT EXTENDED_CAPABILITIES_REPORT AUTO_REPORT_TEMPERATURES \
|
||||
SDSUPPORT SDCARD_SORT_ALPHA AUTO_REPORT_SD_STATUS EMERGENCY_PARSER
|
||||
opt_set GRID_MAX_POINTS_X 16
|
||||
opt_set NOZZLE_TO_PROBE_OFFSET "{ 0, 0, 0 }"
|
||||
opt_set NOZZLE_CLEAN_MIN_TEMP 170
|
||||
exec_test $1 $2 "Re-ARM with NOZZLE_AS_PROBE and many features." "$3"
|
||||
|
||||
# clean up
|
||||
|
|
|
|||
|
|
@ -13,17 +13,15 @@ use_example_configs Azteeg/X5GT
|
|||
exec_test $1 $2 "Azteeg X5GT Example Configuration" "$3"
|
||||
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_SMOOTHIEBOARD
|
||||
opt_set EXTRUDERS 2
|
||||
opt_set TEMP_SENSOR_1 -1
|
||||
opt_set TEMP_SENSOR_BED 5
|
||||
opt_set MOTHERBOARD BOARD_SMOOTHIEBOARD \
|
||||
EXTRUDERS 2 TEMP_SENSOR_1 -1 TEMP_SENSOR_BED 5 \
|
||||
GRID_MAX_POINTS_X 16
|
||||
opt_enable TFTGLCD_PANEL_SPI SDSUPPORT ADAPTIVE_FAN_SLOWING NO_FAN_SLOWING_IN_PID_TUNING \
|
||||
FIX_MOUNTED_PROBE AUTO_BED_LEVELING_BILINEAR G29_RETRY_AND_RECOVER Z_MIN_PROBE_REPEATABILITY_TEST DEBUG_LEVELING_FEATURE \
|
||||
BABYSTEPPING BABYSTEP_XY BABYSTEP_ZPROBE_OFFSET LEVEL_CORNERS_USE_PROBE LEVEL_CORNERS_VERIFY_RAISED \
|
||||
PRINTCOUNTER NOZZLE_PARK_FEATURE NOZZLE_CLEAN_FEATURE SLOW_PWM_HEATERS PIDTEMPBED EEPROM_SETTINGS INCH_MODE_SUPPORT TEMPERATURE_UNITS_SUPPORT \
|
||||
Z_SAFE_HOMING ADVANCED_PAUSE_FEATURE PARK_HEAD_ON_PAUSE \
|
||||
LCD_INFO_MENU ARC_SUPPORT BEZIER_CURVE_SUPPORT EXTENDED_CAPABILITIES_REPORT AUTO_REPORT_TEMPERATURES SDCARD_SORT_ALPHA EMERGENCY_PARSER
|
||||
opt_set GRID_MAX_POINTS_X 16
|
||||
exec_test $1 $2 "Smoothieboard with TFTGLCD_PANEL_SPI and many features" "$3"
|
||||
|
||||
#restore_configs
|
||||
|
|
@ -36,17 +34,13 @@ exec_test $1 $2 "Smoothieboard with TFTGLCD_PANEL_SPI and many features" "$3"
|
|||
# SD_ABORT_ON_ENDSTOP_HIT ADVANCED_OK GCODE_MACROS \
|
||||
# VOLUMETRIC_DEFAULT_ON NO_WORKSPACE_OFFSETS \
|
||||
# EXTRA_FAN_SPEED FWRETRACT MENU_ADDAUTOSTART SDCARD_SORT_ALPHA
|
||||
#opt_set FAN_MIN_PWM 50
|
||||
#opt_set FAN_KICKSTART_TIME 100
|
||||
#opt_set XY_FREQUENCY_LIMIT 15
|
||||
#opt_set FAN_MIN_PWM 50 FAN_KICKSTART_TIME 100 XY_FREQUENCY_LIMIT 15
|
||||
#exec_test $1 $2 "Azteeg X5 MINI WIFI Many less common options" "$3"
|
||||
|
||||
restore_configs
|
||||
use_example_configs delta/generic
|
||||
opt_set MOTHERBOARD BOARD_COHESION3D_REMIX
|
||||
opt_set X_DRIVER_TYPE TMC2130
|
||||
opt_set Y_DRIVER_TYPE TMC2130
|
||||
opt_set Z_DRIVER_TYPE TMC2130
|
||||
opt_set MOTHERBOARD BOARD_COHESION3D_REMIX \
|
||||
X_DRIVER_TYPE TMC2130 Y_DRIVER_TYPE TMC2130 Z_DRIVER_TYPE TMC2130
|
||||
opt_enable AUTO_BED_LEVELING_BILINEAR EEPROM_SETTINGS EEPROM_CHITCHAT MECHANICAL_GANTRY_CALIBRATION \
|
||||
TMC_USE_SW_SPI MONITOR_DRIVER_STATUS STEALTHCHOP_XY STEALTHCHOP_Z HYBRID_THRESHOLD \
|
||||
SENSORLESS_PROBING Z_SAFE_HOMING X_STALL_SENSITIVITY Y_STALL_SENSITIVITY Z_STALL_SENSITIVITY TMC_DEBUG \
|
||||
|
|
|
|||
|
|
@ -10,11 +10,8 @@ set -e
|
|||
# Build with the default configurations
|
||||
#
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_NUCLEO_F767ZI
|
||||
opt_set SERIAL_PORT -1
|
||||
opt_set MOTHERBOARD BOARD_NUCLEO_F767ZI SERIAL_PORT -1 X_DRIVER_TYPE TMC2209 Y_DRIVER_TYPE TMC2208
|
||||
opt_enable BLTOUCH Z_SAFE_HOMING SPEAKER SOFTWARE_DRIVER_ENABLE
|
||||
opt_set X_DRIVER_TYPE TMC2209
|
||||
opt_set Y_DRIVER_TYPE TMC2208
|
||||
exec_test $1 $2 "Mixed timer usage" "$3"
|
||||
|
||||
# clean up
|
||||
|
|
|
|||
|
|
@ -10,20 +10,14 @@ set -e
|
|||
# Build with the default configurations
|
||||
#
|
||||
restore_configs
|
||||
opt_set SERIAL_PORT -1
|
||||
opt_set MOTHERBOARD BOARD_AGCM4_RAMPS_144
|
||||
opt_set TEMP_SENSOR_0 11
|
||||
opt_set TEMP_SENSOR_BED 11
|
||||
opt_set X_DRIVER_TYPE TMC2209
|
||||
opt_set Y_DRIVER_TYPE TMC2209
|
||||
opt_set Z_DRIVER_TYPE TMC2209
|
||||
opt_set Z2_DRIVER_TYPE TMC2209
|
||||
opt_set E0_DRIVER_TYPE TMC2209
|
||||
opt_set RESTORE_LEVELING_AFTER_G28 false
|
||||
opt_set LCD_LANGUAGE it
|
||||
opt_set NUM_Z_STEPPER_DRIVERS 2
|
||||
opt_set HOMING_BUMP_MM "{ 0, 0, 0 }"
|
||||
opt_set SDCARD_CONNECTION LCD
|
||||
opt_set MOTHERBOARD BOARD_AGCM4_RAMPS_144 SERIAL_PORT -1 \
|
||||
TEMP_SENSOR_0 11 TEMP_SENSOR_BED 11 \
|
||||
X_DRIVER_TYPE TMC2209 Y_DRIVER_TYPE TMC2209 Z_DRIVER_TYPE TMC2209 Z2_DRIVER_TYPE TMC2209 E0_DRIVER_TYPE TMC2209 \
|
||||
RESTORE_LEVELING_AFTER_G28 false \
|
||||
LCD_LANGUAGE it \
|
||||
SDCARD_CONNECTION LCD \
|
||||
NUM_Z_STEPPER_DRIVERS 2 \
|
||||
HOMING_BUMP_MM '{ 0, 0, 0 }'
|
||||
opt_enable ENDSTOP_INTERRUPTS_FEATURE S_CURVE_ACCELERATION BLTOUCH Z_MIN_PROBE_REPEATABILITY_TEST \
|
||||
FILAMENT_RUNOUT_SENSOR G26_MESH_VALIDATION MESH_EDIT_GFX_OVERLAY Z_SAFE_HOMING \
|
||||
EEPROM_SETTINGS NOZZLE_PARK_FEATURE SDSUPPORT SD_CHECK_AND_RETRY \
|
||||
|
|
|
|||
|
|
@ -7,8 +7,7 @@
|
|||
set -e
|
||||
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_MALYAN_M200_V2
|
||||
opt_set SERIAL_PORT -1
|
||||
opt_set MOTHERBOARD BOARD_MALYAN_M200_V2 SERIAL_PORT -1
|
||||
exec_test $1 $2 "Malyan M200 v2 Default Config" "$3"
|
||||
|
||||
# cleanup
|
||||
|
|
|
|||
|
|
@ -10,13 +10,8 @@ set -e
|
|||
# Build with the default configurations
|
||||
#
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_BTT_SKR_MINI_E3_V1_0
|
||||
opt_set SERIAL_PORT 1
|
||||
opt_set SERIAL_PORT_2 -1
|
||||
opt_set X_DRIVER_TYPE TMC2209
|
||||
opt_set Y_DRIVER_TYPE TMC2209
|
||||
opt_set Z_DRIVER_TYPE TMC2209
|
||||
opt_set E0_DRIVER_TYPE TMC2209
|
||||
opt_set MOTHERBOARD BOARD_BTT_SKR_MINI_E3_V1_0 SERIAL_PORT 1 SERIAL_PORT_2 -1 \
|
||||
X_DRIVER_TYPE TMC2209 Y_DRIVER_TYPE TMC2209 Z_DRIVER_TYPE TMC2209 E0_DRIVER_TYPE TMC2209
|
||||
opt_enable PINS_DEBUGGING Z_IDLE_HEIGHT
|
||||
|
||||
exec_test $1 $2 "BigTreeTech SKR Mini E3 1.0 - Basic Config with TMC2209 HW Serial" "$3"
|
||||
|
|
|
|||
|
|
@ -10,9 +10,7 @@ set -e
|
|||
# Build with the default configurations
|
||||
#
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_BTT_SKR_MINI_V1_1
|
||||
opt_set SERIAL_PORT 1
|
||||
opt_set SERIAL_PORT_2 -1
|
||||
opt_set MOTHERBOARD BOARD_BTT_SKR_MINI_V1_1 SERIAL_PORT 1 SERIAL_PORT_2 -1
|
||||
exec_test $1 $2 "BigTreeTech SKR Mini v1.1 - Basic Configuration" "$3"
|
||||
|
||||
# clean up
|
||||
|
|
|
|||
|
|
@ -10,13 +10,8 @@ set -e
|
|||
# Build with the default configurations
|
||||
#
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_CCROBOT_MEEB_3DP
|
||||
opt_set SERIAL_PORT 1
|
||||
opt_set SERIAL_PORT_2 -1
|
||||
opt_set X_DRIVER_TYPE TMC2208
|
||||
opt_set Y_DRIVER_TYPE TMC2208
|
||||
opt_set Z_DRIVER_TYPE TMC2208
|
||||
opt_set E0_DRIVER_TYPE TMC2208
|
||||
opt_set MOTHERBOARD BOARD_CCROBOT_MEEB_3DP SERIAL_PORT 1 SERIAL_PORT_2 -1 \
|
||||
X_DRIVER_TYPE TMC2208 Y_DRIVER_TYPE TMC2208 Z_DRIVER_TYPE TMC2208 E0_DRIVER_TYPE TMC2208
|
||||
exec_test $1 $2 "MEEB_3DP - Basic Config with TMC2208 SW Serial" "$3"
|
||||
|
||||
# clean up
|
||||
|
|
|
|||
|
|
@ -10,9 +10,7 @@ set -e
|
|||
# Build with the default configurations
|
||||
#
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_STM32F103RE
|
||||
opt_set EXTRUDERS 2
|
||||
opt_set SERIAL_PORT -1
|
||||
opt_set MOTHERBOARD BOARD_STM32F103RE SERIAL_PORT -1 EXTRUDERS 2
|
||||
opt_enable EEPROM_SETTINGS EEPROM_CHITCHAT REPRAP_DISCOUNT_SMART_CONTROLLER SDSUPPORT \
|
||||
PAREN_COMMENTS GCODE_MOTION_MODES SINGLENOZZLE TOOLCHANGE_FILAMENT_SWAP TOOLCHANGE_PARK \
|
||||
BAUD_RATE_GCODE GCODE_MACROS NOZZLE_PARK_FEATURE NOZZLE_CLEAN_FEATURE
|
||||
|
|
|
|||
|
|
@ -19,11 +19,10 @@ opt_add SDCARD_EEPROM_EMULATION
|
|||
exec_test $1 $2 "Ender 3 v2, SD EEPROM, w/o CLASSIC_JERK" "$3"
|
||||
|
||||
restore_configs
|
||||
opt_set SERIAL_PORT 1
|
||||
opt_set MOTHERBOARD BOARD_CREALITY_V452
|
||||
opt_set MOTHERBOARD BOARD_CREALITY_V452 SERIAL_PORT 1
|
||||
opt_disable NOZZLE_TO_PROBE_OFFSET
|
||||
opt_enable NOZZLE_AS_PROBE Z_SAFE_HOMING Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
opt_enable PROBE_ACTIVATION_SWITCH PROBE_TARE PROBE_TARE_ONLY_WHILE_INACTIVE
|
||||
opt_enable NOZZLE_AS_PROBE Z_SAFE_HOMING Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN \
|
||||
PROBE_ACTIVATION_SWITCH PROBE_TARE PROBE_TARE_ONLY_WHILE_INACTIVE
|
||||
exec_test $1 $2 "Creality V4.5.2 PROBE_ACTIVATION_SWITCH, Probe Tare" "$3"
|
||||
|
||||
# clean up
|
||||
|
|
|
|||
|
|
@ -10,12 +10,10 @@ set -e
|
|||
# Build with the default configurations
|
||||
#
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_BTT_SKR_E3_DIP
|
||||
opt_set SERIAL_PORT 1
|
||||
opt_set SERIAL_PORT_2 -1
|
||||
opt_set X_DRIVER_TYPE TMC2209
|
||||
opt_set Y_DRIVER_TYPE TMC2130
|
||||
exec_test $1 $2 "BigTreeTech SKR E3 DIP v1.0 - Basic Config with mixed TMC Drivers" "$3"
|
||||
opt_set MOTHERBOARD BOARD_BTT_SKR_E3_DIP \
|
||||
SERIAL_PORT 1 SERIAL_PORT_2 -1 \
|
||||
X_DRIVER_TYPE TMC2209 Y_DRIVER_TYPE TMC2130
|
||||
exec_test $1 $2 "BTT SKR E3 DIP 1.0 | Mixed TMC Drivers" "$3"
|
||||
|
||||
# clean up
|
||||
restore_configs
|
||||
|
|
|
|||
|
|
@ -10,16 +10,11 @@ set -e
|
|||
# Build with the default configurations
|
||||
#
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_BTT_SKR_E3_DIP
|
||||
opt_set SERIAL_PORT 1
|
||||
opt_set SERIAL_PORT_2 -1
|
||||
opt_set MOTHERBOARD BOARD_BTT_SKR_E3_DIP SERIAL_PORT 1 SERIAL_PORT_2 -1
|
||||
exec_test $1 $2 "BigTreeTech SKR E3 DIP v1.0 - Basic Configuration" "$3"
|
||||
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_BTT_SKR_CR6
|
||||
opt_set SERIAL_PORT -1
|
||||
opt_set SERIAL_PORT_2 2
|
||||
opt_set TEMP_SENSOR_BED 1
|
||||
opt_set MOTHERBOARD BOARD_BTT_SKR_CR6 SERIAL_PORT -1 SERIAL_PORT_2 2 TEMP_SENSOR_BED 1
|
||||
opt_enable CR10_STOCKDISPLAY \
|
||||
NOZZLE_AS_PROBE Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN Z_SAFE_HOMING \
|
||||
PROBE_ACTIVATION_SWITCH PROBE_TARE PROBE_TARE_ONLY_WHILE_INACTIVE \
|
||||
|
|
|
|||
|
|
@ -8,8 +8,7 @@ set -e
|
|||
|
||||
# Build examples
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_STEVAL_3DP001V1
|
||||
opt_set SERIAL_PORT -1
|
||||
opt_set MOTHERBOARD BOARD_STEVAL_3DP001V1 SERIAL_PORT -1
|
||||
exec_test $1 $2 "STM32F401VE_STEVAL Default Config" "$3"
|
||||
|
||||
# cleanup
|
||||
|
|
|
|||
|
|
@ -10,30 +10,19 @@ set -e
|
|||
# Build with the default configurations
|
||||
#
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_ESPRESSIF_ESP32
|
||||
opt_set MOTHERBOARD BOARD_ESPRESSIF_ESP32 TX_BUFFER_SIZE 64 \
|
||||
WIFI_SSID '"ssid"' WIFI_PWD '"password"'
|
||||
opt_enable WIFISUPPORT WEBSUPPORT GCODE_MACROS BAUD_RATE_GCODE M115_GEOMETRY_REPORT REPETIER_GCODE_M360
|
||||
opt_add WIFI_SSID "\"ssid\""
|
||||
opt_add WIFI_PWD "\"password\""
|
||||
opt_set TX_BUFFER_SIZE 64
|
||||
exec_test $1 $2 "ESP32 with WIFISUPPORT and WEBSUPPORT" "$3"
|
||||
|
||||
#
|
||||
# Build with TMC drivers using hardware serial
|
||||
#
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_ESPRESSIF_ESP32
|
||||
opt_set X_DRIVER_TYPE TMC2209
|
||||
opt_set Y_DRIVER_TYPE TMC2208
|
||||
opt_set Z_DRIVER_TYPE TMC2209
|
||||
opt_set E0_DRIVER_TYPE TMC2209
|
||||
opt_set X_HARDWARE_SERIAL Serial1
|
||||
opt_set Y_HARDWARE_SERIAL Serial1
|
||||
opt_set Z_HARDWARE_SERIAL Serial1
|
||||
opt_set E0_HARDWARE_SERIAL Serial1
|
||||
opt_set X_SLAVE_ADDRESS 0
|
||||
opt_set Y_SLAVE_ADDRESS 1
|
||||
opt_set Z_SLAVE_ADDRESS 2
|
||||
opt_set E0_SLAVE_ADDRESS 3
|
||||
opt_set MOTHERBOARD BOARD_ESPRESSIF_ESP32 \
|
||||
X_DRIVER_TYPE TMC2209 Y_DRIVER_TYPE TMC2208 Z_DRIVER_TYPE TMC2209 E0_DRIVER_TYPE TMC2209 \
|
||||
X_HARDWARE_SERIAL Serial1 Y_HARDWARE_SERIAL Serial1 Z_HARDWARE_SERIAL Serial1 E0_HARDWARE_SERIAL Serial1 \
|
||||
X_SLAVE_ADDRESS 0 Y_SLAVE_ADDRESS 1 Z_SLAVE_ADDRESS 2 E0_SLAVE_ADDRESS 3
|
||||
opt_enable HOTEND_IDLE_TIMEOUT SOFTWARE_DRIVER_ENABLE
|
||||
exec_test $1 $2 "ESP32, TMC HW Serial, Hotend Idle" "$3"
|
||||
|
||||
|
|
|
|||
|
|
@ -10,8 +10,7 @@ set -e
|
|||
# Build with the default configurations
|
||||
#
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_LINUX_RAMPS
|
||||
opt_set TEMP_SENSOR_BED 1
|
||||
opt_set MOTHERBOARD BOARD_LINUX_RAMPS TEMP_SENSOR_BED 1
|
||||
opt_enable PIDTEMPBED EEPROM_SETTINGS BAUD_RATE_GCODE
|
||||
exec_test $1 $2 "Linux with EEPROM" "$3"
|
||||
|
||||
|
|
|
|||
|
|
@ -16,29 +16,25 @@ set -e
|
|||
# Test MESH_BED_LEVELING feature, with LCD
|
||||
#
|
||||
restore_configs
|
||||
opt_set LCD_LANGUAGE an
|
||||
opt_set LCD_LANGUAGE an \
|
||||
POWER_MONITOR_CURRENT_PIN 14 POWER_MONITOR_VOLTAGE_PIN 15 \
|
||||
CLOSED_LOOP_ENABLE_PIN 44 CLOSED_LOOP_MOVE_COMPLETE_PIN 45
|
||||
opt_enable SPINDLE_FEATURE ULTIMAKERCONTROLLER LCD_BED_LEVELING \
|
||||
EEPROM_SETTINGS EEPROM_BOOT_SILENT EEPROM_AUTO_INIT \
|
||||
SENSORLESS_BACKOFF_MM HOMING_BACKOFF_POST_MM HOME_Y_BEFORE_X CODEPENDENT_XY_HOMING \
|
||||
MESH_BED_LEVELING ENABLE_LEVELING_FADE_HEIGHT MESH_G28_REST_ORIGIN \
|
||||
G26_MESH_VALIDATION MESH_EDIT_MENU GCODE_QUOTED_STRINGS \
|
||||
EXTERNAL_CLOSED_LOOP_CONTROLLER POWER_MONITOR_CURRENT POWER_MONITOR_VOLTAGE
|
||||
opt_set POWER_MONITOR_CURRENT_PIN 14
|
||||
opt_set POWER_MONITOR_VOLTAGE_PIN 15
|
||||
opt_set CLOSED_LOOP_ENABLE_PIN 44
|
||||
opt_set CLOSED_LOOP_MOVE_COMPLETE_PIN 45
|
||||
exec_test $1 $2 "Spindle, MESH_BED_LEVELING, closed loop, Power Monitor, and LCD" "$3"
|
||||
|
||||
#
|
||||
# Test DUAL_X_CARRIAGE
|
||||
#
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_ZRIB_V52
|
||||
opt_set LCD_LANGUAGE pt
|
||||
opt_set EXTRUDERS 2
|
||||
opt_set TEMP_SENSOR_1 1
|
||||
opt_set MOTHERBOARD BOARD_ZRIB_V52 \
|
||||
LCD_LANGUAGE pt REPRAPWORLD_KEYPAD_MOVE_STEP 10.0 \
|
||||
EXTRUDERS 2 TEMP_SENSOR_1 1
|
||||
opt_enable USE_XMAX_PLUG DUAL_X_CARRIAGE REPRAPWORLD_KEYPAD
|
||||
opt_set REPRAPWORLD_KEYPAD_MOVE_STEP 10.0
|
||||
exec_test $1 $2 "ZRIB_V52 | DUAL_X_CARRIAGE" "$3"
|
||||
|
||||
#
|
||||
|
|
|
|||
|
|
@ -16,17 +16,10 @@ set -e
|
|||
# Test a probeless build of AUTO_BED_LEVELING_UBL, with lots of extruders
|
||||
#
|
||||
use_example_configs AnimationExample
|
||||
opt_set SHOW_CUSTOM_BOOTSCREEN
|
||||
opt_set MOTHERBOARD BOARD_AZTEEG_X3_PRO
|
||||
opt_set LCD_LANGUAGE fr
|
||||
opt_set EXTRUDERS 5
|
||||
opt_set TEMP_SENSOR_1 1
|
||||
opt_set TEMP_SENSOR_2 5
|
||||
opt_set TEMP_SENSOR_3 20
|
||||
opt_set TEMP_SENSOR_4 1000
|
||||
opt_set TEMP_SENSOR_BED 1
|
||||
opt_set MOTHERBOARD BOARD_AZTEEG_X3_PRO LCD_LANGUAGE fr \
|
||||
EXTRUDERS 5 TEMP_SENSOR_1 1 TEMP_SENSOR_2 5 TEMP_SENSOR_3 20 TEMP_SENSOR_4 1000 TEMP_SENSOR_BED 1
|
||||
opt_enable AUTO_BED_LEVELING_UBL RESTORE_LEVELING_AFTER_G28 DEBUG_LEVELING_FEATURE G26_MESH_VALIDATION ENABLE_LEVELING_FADE_HEIGHT SKEW_CORRECTION \
|
||||
REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER LIGHTWEIGHT_UI STATUS_MESSAGE_SCROLLING BOOT_MARLIN_LOGO_SMALL \
|
||||
REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER LIGHTWEIGHT_UI STATUS_MESSAGE_SCROLLING SHOW_CUSTOM_BOOTSCREEN BOOT_MARLIN_LOGO_SMALL \
|
||||
SDSUPPORT SDCARD_SORT_ALPHA USB_FLASH_DRIVE_SUPPORT AUTO_REPORT_SD_STATUS SCROLL_LONG_FILENAMES CANCEL_OBJECTS SOUND_MENU_ITEM \
|
||||
EEPROM_SETTINGS EEPROM_CHITCHAT GCODE_MACROS CUSTOM_USER_MENUS \
|
||||
MULTI_NOZZLE_DUPLICATION CLASSIC_JERK LIN_ADVANCE EXTRA_LIN_ADVANCE_K QUICK_HOME \
|
||||
|
|
@ -38,26 +31,18 @@ exec_test $1 $2 "Azteeg X3 Pro | EXTRUDERS 5 | RRDFGSC | UBL | LIN_ADVANCE ..."
|
|||
# Add a Sled Z Probe, use UBL Cartesian moves, use Japanese language
|
||||
#
|
||||
use_example_configs AnimationExample
|
||||
opt_set SHOW_CUSTOM_BOOTSCREEN
|
||||
opt_set MOTHERBOARD BOARD_AZTEEG_X3_PRO
|
||||
opt_set LCD_LANGUAGE fr
|
||||
opt_set EXTRUDERS 5
|
||||
opt_set TEMP_SENSOR_1 1
|
||||
opt_set TEMP_SENSOR_2 5
|
||||
opt_set TEMP_SENSOR_3 20
|
||||
opt_set TEMP_SENSOR_4 1000
|
||||
opt_set TEMP_SENSOR_BED 1
|
||||
opt_enable AUTO_BED_LEVELING_UBL RESTORE_LEVELING_AFTER_G28 DEBUG_LEVELING_FEATURE G26_MESH_VALIDATION ENABLE_LEVELING_FADE_HEIGHT SKEW_CORRECTION \
|
||||
REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER LIGHTWEIGHT_UI STATUS_MESSAGE_SCROLLING BOOT_MARLIN_LOGO_SMALL \
|
||||
SDSUPPORT SDCARD_SORT_ALPHA USB_FLASH_DRIVE_SUPPORT SCROLL_LONG_FILENAMES CANCEL_OBJECTS NO_SD_AUTOSTART \
|
||||
opt_set MOTHERBOARD BOARD_AZTEEG_X3_PRO LCD_LANGUAGE jp_kana \
|
||||
EXTRUDERS 5 TEMP_SENSOR_1 1 TEMP_SENSOR_2 5 TEMP_SENSOR_3 20 TEMP_SENSOR_4 1000 TEMP_SENSOR_BED 1
|
||||
opt_enable REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER LIGHTWEIGHT_UI SHOW_CUSTOM_BOOTSCREEN BOOT_MARLIN_LOGO_SMALL \
|
||||
LCD_SET_PROGRESS_MANUALLY PRINT_PROGRESS_SHOW_DECIMALS SHOW_REMAINING_TIME STATUS_MESSAGE_SCROLLING SCROLL_LONG_FILENAMES \
|
||||
SDSUPPORT SDCARD_SORT_ALPHA NO_SD_AUTOSTART USB_FLASH_DRIVE_SUPPORT CANCEL_OBJECTS \
|
||||
Z_PROBE_SLED AUTO_BED_LEVELING_UBL RESTORE_LEVELING_AFTER_G28 DEBUG_LEVELING_FEATURE G26_MESH_VALIDATION ENABLE_LEVELING_FADE_HEIGHT \
|
||||
EEPROM_SETTINGS EEPROM_CHITCHAT GCODE_MACROS CUSTOM_USER_MENUS \
|
||||
MULTI_NOZZLE_DUPLICATION CLASSIC_JERK LIN_ADVANCE QUICK_HOME \
|
||||
LCD_SET_PROGRESS_MANUALLY PRINT_PROGRESS_SHOW_DECIMALS SHOW_REMAINING_TIME \
|
||||
BABYSTEPPING BABYSTEP_XY NANODLP_Z_SYNC I2C_POSITION_ENCODERS M114_DETAIL \
|
||||
Z_PROBE_SLED SKEW_CORRECTION SKEW_CORRECTION_FOR_Z SKEW_CORRECTION_GCODE
|
||||
opt_set LCD_LANGUAGE jp_kana
|
||||
NANODLP_Z_SYNC I2C_POSITION_ENCODERS M114_DETAIL \
|
||||
SKEW_CORRECTION SKEW_CORRECTION_FOR_Z SKEW_CORRECTION_GCODE \
|
||||
BABYSTEPPING BABYSTEP_XY BABYSTEP_ZPROBE_OFFSET DOUBLECLICK_FOR_Z_BABYSTEPPING BABYSTEP_HOTEND_Z_OFFSET BABYSTEP_DISPLAY_TOTAL
|
||||
opt_disable SEGMENT_LEVELED_MOVES
|
||||
opt_enable BABYSTEPPING BABYSTEP_XY BABYSTEP_ZPROBE_OFFSET DOUBLECLICK_FOR_Z_BABYSTEPPING BABYSTEP_HOTEND_Z_OFFSET BABYSTEP_DISPLAY_TOTAL M114_DETAIL
|
||||
exec_test $1 $2 "Azteeg X3 Pro | EXTRUDERS 5 | RRDFGSC | UBL | LIN_ADVANCE | Sled Probe | Skew | JP-Kana | Babystep offsets ..." "$3"
|
||||
|
||||
|
||||
|
|
@ -65,25 +50,16 @@ exec_test $1 $2 "Azteeg X3 Pro | EXTRUDERS 5 | RRDFGSC | UBL | LIN_ADVANCE | Sle
|
|||
# 5 runout sensors with distinct states
|
||||
#
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_AZTEEG_X3_PRO
|
||||
opt_set EXTRUDERS 5
|
||||
opt_set NUM_SERVOS 1
|
||||
opt_set TEMP_SENSOR_1 1
|
||||
opt_set TEMP_SENSOR_2 1
|
||||
opt_set TEMP_SENSOR_3 1
|
||||
opt_set TEMP_SENSOR_4 1
|
||||
opt_set MOTHERBOARD BOARD_AZTEEG_X3_PRO NUM_SERVOS 1 \
|
||||
EXTRUDERS 5 TEMP_SENSOR_1 1 TEMP_SENSOR_2 1 TEMP_SENSOR_3 1 TEMP_SENSOR_4 1 \
|
||||
NUM_RUNOUT_SENSORS 5 FIL_RUNOUT2_PIN 44 FIL_RUNOUT3_PIN 45 FIL_RUNOUT4_PIN 46 FIL_RUNOUT5_PIN 47 \
|
||||
FIL_RUNOUT3_STATE HIGH
|
||||
opt_enable VIKI2 BOOT_MARLIN_LOGO_ANIMATED SDSUPPORT AUTO_REPORT_SD_STATUS \
|
||||
Z_PROBE_SERVO_NR Z_SERVO_ANGLES DEACTIVATE_SERVOS_AFTER_MOVE AUTO_BED_LEVELING_3POINT DEBUG_LEVELING_FEATURE \
|
||||
EEPROM_SETTINGS EEPROM_CHITCHAT M114_DETAIL \
|
||||
NO_VOLUMETRICS EXTENDED_CAPABILITIES_REPORT AUTO_REPORT_TEMPERATURES AUTOTEMP G38_PROBE_TARGET JOYSTICK \
|
||||
DIRECT_STEPPING DETECT_BROKEN_ENDSTOP \
|
||||
FILAMENT_RUNOUT_SENSOR NOZZLE_PARK_FEATURE ADVANCED_PAUSE_FEATURE Z_SAFE_HOMING FIL_RUNOUT3_PULLUP
|
||||
opt_set NUM_RUNOUT_SENSORS 5
|
||||
opt_set FIL_RUNOUT2_PIN 44
|
||||
opt_set FIL_RUNOUT3_PIN 45
|
||||
opt_set FIL_RUNOUT3_STATE HIGH
|
||||
opt_set FIL_RUNOUT4_PIN 46
|
||||
opt_set FIL_RUNOUT5_PIN 47
|
||||
exec_test $1 $2 "Multiple runout sensors (x5) | Distinct runout states" "$3"
|
||||
|
||||
|
||||
|
|
@ -91,27 +67,19 @@ exec_test $1 $2 "Multiple runout sensors (x5) | Distinct runout states" "$3"
|
|||
# Mixing Extruder with 5 steppers, Greek
|
||||
#
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_AZTEEG_X3_PRO
|
||||
opt_set LCD_LANGUAGE el_gr
|
||||
opt_set MOTHERBOARD BOARD_AZTEEG_X3_PRO MIXING_STEPPERS 5 LCD_LANGUAGE ru \
|
||||
NUM_RUNOUT_SENSORS E_STEPPERS FIL_RUNOUT2_PIN 16 FIL_RUNOUT3_PIN 17 FIL_RUNOUT4_PIN 4 FIL_RUNOUT5_PIN 5
|
||||
opt_enable MIXING_EXTRUDER GRADIENT_MIX GRADIENT_VTOOL CR10_STOCKDISPLAY \
|
||||
USE_CONTROLLER_FAN CONTROLLER_FAN_EDITABLE CONTROLLER_FAN_IGNORE_Z \
|
||||
FILAMENT_RUNOUT_SENSOR ADVANCED_PAUSE_FEATURE NOZZLE_PARK_FEATURE
|
||||
opt_set MIXING_STEPPERS 5
|
||||
opt_set NUM_RUNOUT_SENSORS E_STEPPERS
|
||||
opt_set FIL_RUNOUT2_PIN 16
|
||||
opt_set FIL_RUNOUT3_PIN 17
|
||||
opt_set FIL_RUNOUT4_PIN 4
|
||||
opt_set FIL_RUNOUT5_PIN 5
|
||||
opt_set LCD_LANGUAGE ru
|
||||
exec_test $1 $2 "Azteeg X3 | Mixing Extruder (x5) | Gradient Mix | Greek" "$3"
|
||||
|
||||
#
|
||||
# Test SPEAKER with BOARD_BQ_ZUM_MEGA_3D and BQ_LCD_SMART_CONTROLLER
|
||||
#
|
||||
#restore_configs
|
||||
#opt_set MOTHERBOARD BOARD_BQ_ZUM_MEGA_3D
|
||||
#opt_set LCD_FEEDBACK_FREQUENCY_DURATION_MS 10
|
||||
#opt_set LCD_FEEDBACK_FREQUENCY_HZ 100
|
||||
#opt_set MOTHERBOARD BOARD_BQ_ZUM_MEGA_3D \
|
||||
# LCD_FEEDBACK_FREQUENCY_DURATION_MS 10 LCD_FEEDBACK_FREQUENCY_HZ 100
|
||||
#opt_enable BQ_LCD_SMART_CONTROLLER SPEAKER
|
||||
|
||||
#
|
||||
|
|
@ -153,10 +121,7 @@ exec_test $1 $2 "Azteeg X3 | Mixing Extruder (x5) | Gradient Mix | Greek" "$3"
|
|||
#
|
||||
#restore_configs
|
||||
#opt_enable G3D_PANEL SDSUPPORT SDCARD_SORT_ALPHA STATUS_MESSAGE_SCROLLING SCROLL_LONG_FILENAMES
|
||||
#opt_set SDSORT_GCODE true
|
||||
#opt_set SDSORT_USES_RAM true
|
||||
#opt_set SDSORT_USES_STACK true
|
||||
#opt_set SDSORT_CACHE_NAMES true
|
||||
#opt_set SDSORT_GCODE true SDSORT_USES_RAM true SDSORT_USES_STACK true SDSORT_CACHE_NAMES true
|
||||
#exec_test $1 $2 "Stuff" "$3"
|
||||
#
|
||||
# REPRAPWORLD_KEYPAD
|
||||
|
|
|
|||
|
|
@ -7,10 +7,8 @@
|
|||
set -e
|
||||
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_MKS_ROBIN_LITE
|
||||
opt_set SERIAL_PORT 1
|
||||
opt_enable EEPROM_SETTINGS
|
||||
opt_enable SDSUPPORT
|
||||
opt_set MOTHERBOARD BOARD_MKS_ROBIN_LITE SERIAL_PORT 1
|
||||
opt_enable EEPROM_SETTINGS SDSUPPORT
|
||||
exec_test $1 $2 "Default Configuration with Fallback SD EEPROM" "$3"
|
||||
|
||||
# cleanup
|
||||
|
|
|
|||
|
|
@ -8,9 +8,7 @@
|
|||
set -e
|
||||
|
||||
use_example_configs Mks/Robin
|
||||
opt_set MOTHERBOARD BOARD_MKS_ROBIN_MINI
|
||||
opt_set EXTRUDERS 1
|
||||
opt_set TEMP_SENSOR_1 0
|
||||
opt_set MOTHERBOARD BOARD_MKS_ROBIN_MINI EXTRUDERS 1 TEMP_SENSOR_1 0
|
||||
exec_test $1 $2 "MKS Robin mini" "$3"
|
||||
|
||||
# cleanup
|
||||
|
|
|
|||
|
|
@ -49,11 +49,9 @@ exec_test $1 $2 "MKS Robin v2 nano New Color UI 480x320 SPI" "$3"
|
|||
# (Robin v2 nano has no FSMC interface)
|
||||
#
|
||||
use_example_configs Mks/Robin
|
||||
opt_set MOTHERBOARD BOARD_MKS_ROBIN_NANO_V2
|
||||
opt_set MOTHERBOARD BOARD_MKS_ROBIN_NANO_V2 X_DRIVER_TYPE TMC2209 Y_DRIVER_TYPE TMC2209
|
||||
opt_disable TFT_INTERFACE_FSMC TFT_COLOR_UI TOUCH_SCREEN TFT_RES_320x240
|
||||
opt_enable TFT_INTERFACE_SPI TFT_LVGL_UI TFT_RES_480x320
|
||||
opt_set X_DRIVER_TYPE TMC2209
|
||||
opt_set Y_DRIVER_TYPE TMC2209
|
||||
exec_test $1 $2 "MKS Robin v2 nano LVGL SPI + TMC" "$3"
|
||||
|
||||
#
|
||||
|
|
|
|||
|
|
@ -58,11 +58,9 @@ exec_test $1 $2 "MKS Robin v2 nano New Color UI 480x320 SPI" "$3"
|
|||
# (Robin v2 nano has no FSMC interface)
|
||||
#
|
||||
# use_example_configs Mks/Robin
|
||||
# opt_set MOTHERBOARD BOARD_MKS_ROBIN_NANO_V2
|
||||
# opt_set MOTHERBOARD BOARD_MKS_ROBIN_NANO_V2 X_DRIVER_TYPE TMC2209 Y_DRIVER_TYPE TMC2209
|
||||
# opt_disable TFT_INTERFACE_FSMC TFT_COLOR_UI TOUCH_SCREEN TFT_RES_320x240
|
||||
# opt_enable TFT_INTERFACE_SPI TFT_LVGL_UI TFT_RES_480x320
|
||||
# opt_set X_DRIVER_TYPE TMC2209
|
||||
# opt_set Y_DRIVER_TYPE TMC2209
|
||||
# exec_test $1 $2 "MKS Robin v2 nano LVGL SPI + TMC" "$3"
|
||||
|
||||
# cleanup
|
||||
|
|
|
|||
|
|
@ -8,13 +8,11 @@ set -e
|
|||
|
||||
use_example_configs Mks/Robin_Pro
|
||||
opt_enable EMERGENCY_PARSER
|
||||
opt_set SERIAL_PORT 3
|
||||
opt_disable SERIAL_PORT_2
|
||||
opt_set SDCARD_CONNECTION LCD
|
||||
opt_set X_DRIVER_TYPE TMC2209
|
||||
opt_set Y_DRIVER_TYPE TMC2130
|
||||
opt_set TEMP_SENSOR_BED 1
|
||||
opt_disable THERMAL_PROTECTION_HOTENDS
|
||||
opt_set SERIAL_PORT 3 \
|
||||
SDCARD_CONNECTION LCD \
|
||||
X_DRIVER_TYPE TMC2209 Y_DRIVER_TYPE TMC2130 \
|
||||
TEMP_SENSOR_BED 1
|
||||
opt_disable SERIAL_PORT_2 THERMAL_PROTECTION_HOTENDS
|
||||
exec_test $1 $2 "MKS Robin Pro, TMC Drivers, no thermal protection" "$3"
|
||||
|
||||
# cleanup
|
||||
|
|
|
|||
|
|
@ -10,22 +10,14 @@ set -e
|
|||
# Lots of options - Formerly the first Mega2560 test
|
||||
#
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_RAMBO
|
||||
opt_set EXTRUDERS 2
|
||||
opt_set TEMP_SENSOR_0 -2
|
||||
opt_set TEMP_SENSOR_1 1
|
||||
opt_set TEMP_SENSOR_BED 2
|
||||
opt_set TEMP_SENSOR_PROBE 1
|
||||
opt_add TEMP_PROBE_PIN 12
|
||||
opt_set TEMP_SENSOR_CHAMBER 3
|
||||
opt_add TEMP_CHAMBER_PIN 3
|
||||
opt_add HEATER_CHAMBER_PIN 45
|
||||
opt_set GRID_MAX_POINTS_X 16
|
||||
opt_set FANMUX0_PIN 53
|
||||
opt_set Z_HOME_DIR 1
|
||||
opt_enable USE_ZMAX_PLUG
|
||||
opt_set MOTHERBOARD BOARD_RAMBO \
|
||||
EXTRUDERS 2 TEMP_SENSOR_0 -2 TEMP_SENSOR_1 1 TEMP_SENSOR_BED 2 \
|
||||
TEMP_SENSOR_PROBE 1 TEMP_PROBE_PIN 12 \
|
||||
TEMP_SENSOR_CHAMBER 3 TEMP_CHAMBER_PIN 3 HEATER_CHAMBER_PIN 45 \
|
||||
Z_HOME_DIR 1 GRID_MAX_POINTS_X 16 \
|
||||
FANMUX0_PIN 53
|
||||
opt_disable USE_ZMIN_PLUG Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN USE_WATCHDOG
|
||||
opt_enable REPRAP_DISCOUNT_SMART_CONTROLLER LCD_PROGRESS_BAR LCD_PROGRESS_BAR_TEST \
|
||||
opt_enable USE_ZMAX_PLUG REPRAP_DISCOUNT_SMART_CONTROLLER LCD_PROGRESS_BAR LCD_PROGRESS_BAR_TEST \
|
||||
FIX_MOUNTED_PROBE CODEPENDENT_XY_HOMING PIDTEMPBED PROBE_TEMP_COMPENSATION \
|
||||
PREHEAT_BEFORE_PROBING PROBING_HEATERS_OFF PROBING_FANS_OFF PROBING_STEPPERS_OFF WAIT_FOR_BED_HEATER \
|
||||
EEPROM_SETTINGS SDSUPPORT SD_REPRINT_LAST_SELECTED_FILE BINARY_FILE_TRANSFER \
|
||||
|
|
@ -50,12 +42,10 @@ exec_test $1 $2 "RAMBO | EXTRUDERS 2 | CHAR LCD + SD | FIX Probe | ABL-Linear |
|
|||
# Full size Rambo Dual Endstop CNC
|
||||
#
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_RAMBO
|
||||
opt_set EXTRUDERS 0
|
||||
opt_set TEMP_SENSOR_0 999
|
||||
opt_set DUMMY_THERMISTOR_999_VALUE 170
|
||||
opt_set DIGIPOT_MOTOR_CURRENT '{ 120, 120, 120, 120, 120 }'
|
||||
opt_set LEVEL_CORNERS_LEVELING_ORDER '{ LF, RF }'
|
||||
opt_set MOTHERBOARD BOARD_RAMBO \
|
||||
EXTRUDERS 0 TEMP_SENSOR_0 999 DUMMY_THERMISTOR_999_VALUE 170 \
|
||||
DIGIPOT_MOTOR_CURRENT '{ 120, 120, 120, 120, 120 }' \
|
||||
LEVEL_CORNERS_LEVELING_ORDER '{ LF, RF }'
|
||||
opt_enable USE_XMAX_PLUG USE_YMAX_PLUG USE_ZMAX_PLUG \
|
||||
REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER REVERSE_ENCODER_DIRECTION SDSUPPORT EEPROM_SETTINGS \
|
||||
S_CURVE_ACCELERATION X_DUAL_STEPPER_DRIVERS X_DUAL_ENDSTOPS Y_DUAL_STEPPER_DRIVERS Y_DUAL_ENDSTOPS \
|
||||
|
|
@ -68,9 +58,7 @@ exec_test $1 $2 "Rambo CNC Configuration" "$3"
|
|||
# Rambo heated bed only
|
||||
#
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_RAMBO
|
||||
opt_set EXTRUDERS 0
|
||||
opt_set TEMP_SENSOR_BED 1
|
||||
opt_set MOTHERBOARD BOARD_RAMBO EXTRUDERS 0 TEMP_SENSOR_BED 1
|
||||
opt_enable REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
||||
exec_test $1 $2 "Rambo heated bed only" "$3"
|
||||
|
||||
|
|
@ -78,18 +66,18 @@ exec_test $1 $2 "Rambo heated bed only" "$3"
|
|||
# Build with the default configurations
|
||||
#
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_EINSY_RAMBO
|
||||
opt_set X_DRIVER_TYPE TMC2130
|
||||
opt_set Y_DRIVER_TYPE TMC2130
|
||||
opt_set Z_DRIVER_TYPE TMC2130
|
||||
opt_set E0_DRIVER_TYPE TMC2130
|
||||
opt_set MOTHERBOARD BOARD_EINSY_RAMBO \
|
||||
X_DRIVER_TYPE TMC2130 Y_DRIVER_TYPE TMC2130 Z_DRIVER_TYPE TMC2130 E0_DRIVER_TYPE TMC2130
|
||||
exec_test $1 $2 "Einsy RAMBo with TMC2130" "$3"
|
||||
|
||||
#
|
||||
# Test MINIRAMBO with PWM_MOTOR_CURRENT and many features
|
||||
#
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_MINIRAMBO
|
||||
opt_set MOTHERBOARD BOARD_MINIRAMBO \
|
||||
CONTROLLERFAN_SPEED_IDLE 128 \
|
||||
PWM_MOTOR_CURRENT '{ 1300, 1300, 1250 }' \
|
||||
I2C_SLAVE_ADDRESS 63
|
||||
opt_enable EEPROM_SETTINGS EEPROM_CHITCHAT REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER \
|
||||
SDSUPPORT PCA9632 SOUND_MENU_ITEM GCODE_REPEAT_MARKERS \
|
||||
AUTO_BED_LEVELING_BILINEAR PROBE_MANUALLY LCD_BED_LEVELING G26_MESH_VALIDATION MESH_EDIT_MENU \
|
||||
|
|
@ -98,23 +86,23 @@ opt_enable EEPROM_SETTINGS EEPROM_CHITCHAT REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CO
|
|||
NOZZLE_PARK_FEATURE NOZZLE_CLEAN_FEATURE \
|
||||
ADVANCED_PAUSE_FEATURE PARK_HEAD_ON_PAUSE ADVANCED_PAUSE_CONTINUOUS_PURGE FILAMENT_LOAD_UNLOAD_GCODES \
|
||||
PRINTCOUNTER SERVICE_NAME_1 SERVICE_INTERVAL_1 M114_DETAIL
|
||||
opt_set CONTROLLERFAN_SPEED_IDLE 128
|
||||
opt_add M100_FREE_MEMORY_DUMPER
|
||||
opt_add M100_FREE_MEMORY_CORRUPTOR
|
||||
opt_set PWM_MOTOR_CURRENT "{ 1300, 1300, 1250 }"
|
||||
opt_set I2C_SLAVE_ADDRESS 63
|
||||
exec_test $1 $2 "MINIRAMBO | RRDGFSC | M100 | PWM_MOTOR_CURRENT | PRINTCOUNTER | Advanced Pause ..." "$3"
|
||||
|
||||
#
|
||||
# Test many less common options
|
||||
#
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_RAMBO
|
||||
opt_set TEMP_SENSOR_0 -2
|
||||
opt_set DIGIPOT_I2C_NUM_CHANNELS 5
|
||||
opt_set LCD_LANGUAGE it
|
||||
opt_set MIXING_STEPPERS 2
|
||||
opt_set SERVO_DELAY "{ 300, 300, 300 }"
|
||||
opt_set MOTHERBOARD BOARD_RAMBO \
|
||||
TEMP_SENSOR_0 -2 \
|
||||
DIGIPOT_I2C_NUM_CHANNELS 5 \
|
||||
LCD_LANGUAGE it \
|
||||
MIXING_STEPPERS 2 \
|
||||
SERVO_DELAY '{ 300, 300, 300 }' \
|
||||
CONTROLLER_FAN_PIN X_MAX_PIN FILWIDTH_PIN 5 \
|
||||
FAN_MIN_PWM 50 FAN_KICKSTART_TIME 100 \
|
||||
XY_FREQUENCY_LIMIT 15
|
||||
opt_enable COREYX USE_XMAX_PLUG MIXING_EXTRUDER GRADIENT_MIX \
|
||||
BABYSTEPPING BABYSTEP_DISPLAY_TOTAL FILAMENT_LCD_DISPLAY \
|
||||
REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER MENU_ADDAUTOSTART SDSUPPORT SDCARD_SORT_ALPHA \
|
||||
|
|
@ -124,11 +112,6 @@ opt_enable COREYX USE_XMAX_PLUG MIXING_EXTRUDER GRADIENT_MIX \
|
|||
SD_ABORT_ON_ENDSTOP_HIT HOST_ACTION_COMMANDS HOST_PROMPT_SUPPORT ADVANCED_OK M114_DETAIL \
|
||||
VOLUMETRIC_DEFAULT_ON NO_WORKSPACE_OFFSETS EXTRA_FAN_SPEED FWRETRACT \
|
||||
USE_CONTROLLER_FAN CONTROLLER_FAN_EDITABLE CONTROLLER_FAN_USE_Z_ONLY
|
||||
opt_set CONTROLLER_FAN_PIN X_MAX_PIN
|
||||
opt_set FAN_MIN_PWM 50
|
||||
opt_set FAN_KICKSTART_TIME 100
|
||||
opt_set XY_FREQUENCY_LIMIT 15
|
||||
opt_add FILWIDTH_PIN 5
|
||||
exec_test $1 $2 "Rambo | CoreXY, Gradient Mix | Endstop Int. | Home Y > X | FW Retract ..." "$3"
|
||||
|
||||
# clean up
|
||||
|
|
|
|||
|
|
@ -8,31 +8,23 @@ set -e
|
|||
|
||||
# Build examples
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_RUMBA32_V1_0
|
||||
opt_set SERIAL_PORT -1
|
||||
opt_set MOTHERBOARD BOARD_RUMBA32_V1_0 SERIAL_PORT -1 \
|
||||
TEMP_SENSOR_BED 1 X_DRIVER_TYPE TMC2130
|
||||
opt_disable PIDTEMP
|
||||
opt_enable PIDTEMPBED
|
||||
opt_set TEMP_SENSOR_BED 1
|
||||
opt_disable THERMAL_PROTECTION_BED
|
||||
opt_set X_DRIVER_TYPE TMC2130
|
||||
exec_test $1 $2 "RUMBA32 V1.0 with TMC2130, PID Bed, and bed thermal protection disabled" "$3"
|
||||
|
||||
# Build examples
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_RUMBA32_V1_1
|
||||
opt_set SERIAL_PORT -1
|
||||
opt_set MOTHERBOARD BOARD_RUMBA32_V1_1 SERIAL_PORT -1 \
|
||||
TEMP_SENSOR_BED 1 X_DRIVER_TYPE TMC2130 Y_DRIVER_TYPE TMC2208
|
||||
opt_enable PIDTEMPBED EEPROM_SETTINGS EEPROM_CHITCHAT REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
||||
opt_set TEMP_SENSOR_BED 1
|
||||
opt_set X_DRIVER_TYPE TMC2130
|
||||
opt_set Y_DRIVER_TYPE TMC2208
|
||||
exec_test $1 $2 "RUMBA32 V1.1 with TMC2130, TMC2208, PID Bed, EEPROM settings, and graphic LCD controller" "$3"
|
||||
|
||||
# Build examples
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_RUMBA32_MKS
|
||||
opt_set SERIAL_PORT -1
|
||||
opt_set X_DRIVER_TYPE TMC2130
|
||||
opt_set Y_DRIVER_TYPE TMC2208
|
||||
opt_set MOTHERBOARD BOARD_RUMBA32_MKS SERIAL_PORT -1 X_DRIVER_TYPE TMC2130 Y_DRIVER_TYPE TMC2208
|
||||
exec_test $1 $2 "RUMBA32 MKS Default Config with Mixed TMC Drivers" "$3"
|
||||
|
||||
# cleanup
|
||||
|
|
|
|||
|
|
@ -10,10 +10,10 @@ set -e
|
|||
# Start with default configurations...
|
||||
#
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_SANGUINOLOLU_12
|
||||
opt_set LCD_LANGUAGE de
|
||||
opt_set MOTHERBOARD BOARD_SANGUINOLOLU_12 \
|
||||
LCD_LANGUAGE de \
|
||||
CONTROLLER_FAN_PIN 27
|
||||
opt_enable MINIPANEL USE_CONTROLLER_FAN CONTROLLER_FAN_EDITABLE
|
||||
opt_set CONTROLLER_FAN_PIN 27
|
||||
exec_test $1 $2 "Default Configuration | MINIPANAL | CONTROLLER_FAN" "$3"
|
||||
|
||||
#
|
||||
|
|
|
|||
|
|
@ -22,9 +22,10 @@ exec_test $1 $2 "Teensy3.1 with Zero Endstops" "$3"
|
|||
# Test many features together
|
||||
#
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_TEENSY31_32
|
||||
opt_set TEMP_SENSOR_0 1
|
||||
opt_set TEMP_SENSOR_BED 1
|
||||
opt_set MOTHERBOARD BOARD_TEENSY31_32 \
|
||||
TEMP_SENSOR_0 1 TEMP_SENSOR_BED 1 \
|
||||
I2C_SLAVE_ADDRESS 63 \
|
||||
GRID_MAX_POINTS_X 16
|
||||
opt_enable EEPROM_SETTINGS FILAMENT_WIDTH_SENSOR CALIBRATION_GCODE BAUD_RATE_GCODE \
|
||||
FIX_MOUNTED_PROBE Z_SAFE_HOMING AUTO_BED_LEVELING_BILINEAR DEBUG_LEVELING_FEATURE Z_MIN_PROBE_REPEATABILITY_TEST \
|
||||
BABYSTEPPING BABYSTEP_XY BABYSTEP_ZPROBE_OFFSET PRINTCOUNTER SLOW_PWM_HEATERS PIDTEMPBED \
|
||||
|
|
@ -33,6 +34,4 @@ opt_enable EEPROM_SETTINGS FILAMENT_WIDTH_SENSOR CALIBRATION_GCODE BAUD_RATE_GCO
|
|||
ARC_SUPPORT BEZIER_CURVE_SUPPORT EXPERIMENTAL_I2CBUS EXTENDED_CAPABILITIES_REPORT AUTO_REPORT_TEMPERATURES \
|
||||
PHOTO_GCODE PHOTO_POSITION PHOTO_SWITCH_POSITION PHOTO_SWITCH_MS PHOTO_DELAY_MS PHOTO_RETRACT_MM \
|
||||
HOST_ACTION_COMMANDS HOST_PROMPT_SUPPORT
|
||||
opt_set I2C_SLAVE_ADDRESS 63
|
||||
opt_set GRID_MAX_POINTS_X 16
|
||||
exec_test $1 $2 "Teensy3.1 with many features" "$3"
|
||||
|
|
|
|||
|
|
@ -14,11 +14,10 @@ exec_test $1 $2 "Teensy3.5 with default config" "$3"
|
|||
# Test as many features together as possible
|
||||
#
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_TEENSY35_36
|
||||
opt_set EXTRUDERS 2
|
||||
opt_set TEMP_SENSOR_0 1
|
||||
opt_set TEMP_SENSOR_1 5
|
||||
opt_set TEMP_SENSOR_BED 1
|
||||
opt_set MOTHERBOARD BOARD_TEENSY35_36 \
|
||||
EXTRUDERS 2 TEMP_SENSOR_0 1 TEMP_SENSOR_1 5 TEMP_SENSOR_BED 1 \
|
||||
I2C_SLAVE_ADDRESS 63 \
|
||||
GRID_MAX_POINTS_X 16
|
||||
opt_enable REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER LCD_INFO_MENU SDSUPPORT SDCARD_SORT_ALPHA \
|
||||
FILAMENT_WIDTH_SENSOR FILAMENT_LCD_DISPLAY CALIBRATION_GCODE BAUD_RATE_GCODE SOUND_MENU_ITEM \
|
||||
FIX_MOUNTED_PROBE Z_SAFE_HOMING AUTO_BED_LEVELING_BILINEAR Z_MIN_PROBE_REPEATABILITY_TEST DEBUG_LEVELING_FEATURE \
|
||||
|
|
@ -27,8 +26,6 @@ opt_enable REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER LCD_INFO_MENU SDSUPPORT
|
|||
ADVANCED_PAUSE_FEATURE ARC_SUPPORT BEZIER_CURVE_SUPPORT EXPERIMENTAL_I2CBUS EXTENDED_CAPABILITIES_REPORT AUTO_REPORT_TEMPERATURES PARK_HEAD_ON_PAUSE \
|
||||
PHOTO_GCODE PHOTO_POSITION PHOTO_SWITCH_POSITION PHOTO_SWITCH_MS PHOTO_DELAY_MS PHOTO_RETRACT_MM \
|
||||
HOST_ACTION_COMMANDS HOST_PROMPT_SUPPORT
|
||||
opt_set I2C_SLAVE_ADDRESS 63
|
||||
opt_set GRID_MAX_POINTS_X 16
|
||||
exec_test $1 $2 "Teensy3.5 with many features" "$3"
|
||||
|
||||
#
|
||||
|
|
@ -43,10 +40,9 @@ exec_test $1 $2 "Sled Z Probe with Linear leveling" "$3"
|
|||
# Test a Servo Probe
|
||||
#
|
||||
# restore_configs
|
||||
# opt_set MOTHERBOARD BOARD_TEENSY35_36
|
||||
# opt_set MOTHERBOARD BOARD_TEENSY35_36 NUM_SERVOS 1
|
||||
# opt_enable Z_PROBE_SERVO_NR Z_SERVO_ANGLES DEACTIVATE_SERVOS_AFTER_MOVE \
|
||||
# AUTO_BED_LEVELING_3POINT DEBUG_LEVELING_FEATURE EEPROM_SETTINGS
|
||||
# opt_set NUM_SERVOS 1
|
||||
# exec_test $1 $2 "Servo Probe"
|
||||
#
|
||||
# ...with AUTO_BED_LEVELING_3POINT, DEBUG_LEVELING_FEATURE, EEPROM_SETTINGS, EEPROM_CHITCHAT, EXTENDED_CAPABILITIES_REPORT, and AUTO_REPORT_TEMPERATURES
|
||||
|
|
@ -59,28 +55,23 @@ exec_test $1 $2 "Sled Z Probe with Linear leveling" "$3"
|
|||
# Test MAGNETIC_PARKING_EXTRUDER with LCD
|
||||
#
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_TEENSY35_36
|
||||
opt_set EXTRUDERS 2
|
||||
opt_set TEMP_SENSOR_1 1
|
||||
opt_enable MAGNETIC_PARKING_EXTRUDER ULTIMAKERCONTROLLER
|
||||
opt_set MOTHERBOARD BOARD_TEENSY35_36 EXTRUDERS 2 TEMP_SENSOR_1 1 SOL0_PIN 29
|
||||
opt_enable PARKING_EXTRUDER ULTIMAKERCONTROLLER
|
||||
exec_test $1 $2 "MAGNETIC_PARKING_EXTRUDER with LCD" "$3"
|
||||
|
||||
#
|
||||
# Mixing Extruder
|
||||
#
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_TEENSY35_36
|
||||
opt_set MOTHERBOARD BOARD_TEENSY35_36 MIXING_STEPPERS 2
|
||||
opt_enable MIXING_EXTRUDER DIRECT_MIXING_IN_G1 GRADIENT_MIX GRADIENT_VTOOL REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
||||
opt_set MIXING_STEPPERS 2
|
||||
exec_test $1 $2 "Mixing Extruder" "$3"
|
||||
|
||||
#
|
||||
# Test SWITCHING_EXTRUDER
|
||||
#
|
||||
# restore_configs
|
||||
# opt_set MOTHERBOARD BOARD_TEENSY35_36
|
||||
# opt_set EXTRUDERS 2
|
||||
# opt_set NUM_SERVOS 1
|
||||
# opt_set MOTHERBOARD BOARD_TEENSY35_36 EXTRUDERS 2 NUM_SERVOS 1
|
||||
# opt_enable SWITCHING_EXTRUDER ULTIMAKERCONTROLLER
|
||||
# exec_test $1 $2 "SWITCHING_EXTRUDER"
|
||||
|
||||
|
|
@ -88,15 +79,11 @@ exec_test $1 $2 "Mixing Extruder" "$3"
|
|||
# Enable COREXY
|
||||
#
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_TEENSY35_36
|
||||
opt_enable COREXY
|
||||
opt_set X_DRIVER_TYPE TMC5160
|
||||
opt_set Y_DRIVER_TYPE TMC5160
|
||||
opt_set X_MIN_ENDSTOP_INVERTING true
|
||||
opt_set Y_MIN_ENDSTOP_INVERTING true
|
||||
opt_add X_CS_PIN 46
|
||||
opt_add Y_CS_PIN 47
|
||||
opt_enable USE_ZMIN_PLUG MONITOR_DRIVER_STATUS SENSORLESS_HOMING
|
||||
opt_set MOTHERBOARD BOARD_TEENSY35_36 \
|
||||
X_DRIVER_TYPE TMC5160 Y_DRIVER_TYPE TMC5160 \
|
||||
X_MIN_ENDSTOP_INVERTING true Y_MIN_ENDSTOP_INVERTING true \
|
||||
X_CS_PIN 46 Y_CS_PIN 47
|
||||
opt_enable COREXY USE_ZMIN_PLUG MONITOR_DRIVER_STATUS SENSORLESS_HOMING
|
||||
exec_test $1 $2 "Teensy 3.5/3.6 COREXY" "$3"
|
||||
|
||||
#
|
||||
|
|
@ -111,11 +98,9 @@ exec_test $1 $2 "Teensy 3.5/3.6 COREXZ" "$3"
|
|||
# Enable Dual Z with Dual Z endstops
|
||||
#
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_TEENSY35_36
|
||||
opt_set NUM_Z_STEPPER_DRIVERS 2
|
||||
opt_set MOTHERBOARD BOARD_TEENSY35_36 NUM_Z_STEPPER_DRIVERS 2 Z2_MAX_PIN 2
|
||||
opt_enable Z_MULTI_ENDSTOPS USE_XMAX_PLUG
|
||||
pins_set ramps/RAMPS X_MAX_PIN -1
|
||||
opt_add Z2_MAX_PIN 2
|
||||
exec_test $1 $2 "Dual Z with Dual Z endstops" "$3"
|
||||
|
||||
# Clean up
|
||||
|
|
|
|||
|
|
@ -14,11 +14,10 @@ exec_test $1 $2 "Teensy4.1 with default config" "$3"
|
|||
# Test as many features together as possible
|
||||
#
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_TEENSY41
|
||||
opt_set EXTRUDERS 2
|
||||
opt_set TEMP_SENSOR_0 1
|
||||
opt_set TEMP_SENSOR_1 5
|
||||
opt_set TEMP_SENSOR_BED 1
|
||||
opt_set MOTHERBOARD BOARD_TEENSY41 \
|
||||
EXTRUDERS 2 TEMP_SENSOR_0 1 TEMP_SENSOR_1 5 TEMP_SENSOR_BED 1 \
|
||||
I2C_SLAVE_ADDRESS 63 \
|
||||
GRID_MAX_POINTS_X 16
|
||||
opt_enable EXTENSIBLE_UI LCD_INFO_MENU SDSUPPORT SDCARD_SORT_ALPHA \
|
||||
FILAMENT_LCD_DISPLAY CALIBRATION_GCODE BAUD_RATE_GCODE \
|
||||
FIX_MOUNTED_PROBE Z_SAFE_HOMING AUTO_BED_LEVELING_BILINEAR Z_MIN_PROBE_REPEATABILITY_TEST DEBUG_LEVELING_FEATURE \
|
||||
|
|
@ -28,8 +27,6 @@ opt_enable EXTENSIBLE_UI LCD_INFO_MENU SDSUPPORT SDCARD_SORT_ALPHA \
|
|||
PHOTO_GCODE PHOTO_POSITION PHOTO_SWITCH_POSITION PHOTO_SWITCH_MS PHOTO_DELAY_MS PHOTO_RETRACT_MM \
|
||||
HOST_ACTION_COMMANDS HOST_PROMPT_SUPPORT
|
||||
opt_add EXTUI_EXAMPLE
|
||||
opt_set I2C_SLAVE_ADDRESS 63
|
||||
opt_set GRID_MAX_POINTS_X 16
|
||||
exec_test $1 $2 "Teensy4.1 with many features" "$3"
|
||||
|
||||
#
|
||||
|
|
@ -60,10 +57,8 @@ exec_test $1 $2 "Sled Z Probe with Linear leveling" "$3"
|
|||
# Test MAGNETIC_PARKING_EXTRUDER with no LCD
|
||||
#
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_TEENSY41
|
||||
opt_set EXTRUDERS 2
|
||||
opt_set TEMP_SENSOR_1 1
|
||||
opt_set SERIAL_PORT_2 -2
|
||||
opt_set MOTHERBOARD BOARD_TEENSY41 SERIAL_PORT_2 -2 \
|
||||
EXTRUDERS 2 TEMP_SENSOR_1 1
|
||||
opt_enable EEPROM_SETTINGS MAGNETIC_PARKING_EXTRUDER
|
||||
exec_test $1 $2 "Ethernet, EEPROM, Magnetic Parking Extruder, No LCD" "$3"
|
||||
|
||||
|
|
@ -71,18 +66,15 @@ exec_test $1 $2 "Ethernet, EEPROM, Magnetic Parking Extruder, No LCD" "$3"
|
|||
# Mixing Extruder
|
||||
#
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_TEENSY41
|
||||
opt_set MOTHERBOARD BOARD_TEENSY41 MIXING_STEPPERS 2
|
||||
opt_enable MIXING_EXTRUDER DIRECT_MIXING_IN_G1 GRADIENT_MIX GRADIENT_VTOOL
|
||||
opt_set MIXING_STEPPERS 2
|
||||
exec_test $1 $2 "Mixing Extruder" "$3"
|
||||
|
||||
#
|
||||
# Test SWITCHING_EXTRUDER
|
||||
#
|
||||
# restore_configs
|
||||
# opt_set MOTHERBOARD BOARD_TEENSY41
|
||||
# opt_set EXTRUDERS 2
|
||||
# opt_set NUM_SERVOS 1
|
||||
# opt_set MOTHERBOARD BOARD_TEENSY41 EXTRUDERS 2 NUM_SERVOS 1
|
||||
# opt_enable SWITCHING_EXTRUDER ULTIMAKERCONTROLLER
|
||||
# exec_test $1 $2 "SWITCHING_EXTRUDER" "$3"
|
||||
|
||||
|
|
@ -90,15 +82,11 @@ exec_test $1 $2 "Mixing Extruder" "$3"
|
|||
# Enable COREXY
|
||||
#
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_TEENSY41
|
||||
opt_enable COREXY
|
||||
opt_set X_DRIVER_TYPE TMC5160
|
||||
opt_set Y_DRIVER_TYPE TMC5160
|
||||
opt_set X_MIN_ENDSTOP_INVERTING true
|
||||
opt_set Y_MIN_ENDSTOP_INVERTING true
|
||||
opt_add X_CS_PIN 46
|
||||
opt_add Y_CS_PIN 47
|
||||
opt_enable USE_ZMIN_PLUG MONITOR_DRIVER_STATUS SENSORLESS_HOMING
|
||||
opt_set MOTHERBOARD BOARD_TEENSY41 \
|
||||
X_DRIVER_TYPE TMC5160 Y_DRIVER_TYPE TMC5160 \
|
||||
X_MIN_ENDSTOP_INVERTING true Y_MIN_ENDSTOP_INVERTING true \
|
||||
X_CS_PIN 46 Y_CS_PIN 47
|
||||
opt_enable COREXY USE_ZMIN_PLUG MONITOR_DRIVER_STATUS SENSORLESS_HOMING
|
||||
exec_test $1 $2 "Teensy 4.0/4.1 COREXY" "$3"
|
||||
|
||||
#
|
||||
|
|
@ -113,11 +101,9 @@ exec_test $1 $2 "Teensy 4.0/4.1 COREXZ" "$3"
|
|||
# Enable Dual Z with Dual Z endstops
|
||||
#
|
||||
restore_configs
|
||||
opt_set MOTHERBOARD BOARD_TEENSY41
|
||||
opt_set MOTHERBOARD BOARD_TEENSY41 NUM_Z_STEPPER_DRIVERS 2 Z2_MAX_PIN 2
|
||||
opt_enable Z_MULTI_ENDSTOPS USE_XMAX_PLUG
|
||||
opt_set NUM_Z_STEPPER_DRIVERS 2
|
||||
pins_set ramps/RAMPS X_MAX_PIN -1
|
||||
opt_add Z2_MAX_PIN 2
|
||||
exec_test $1 $2 "Dual Z with Dual Z endstops" "$3"
|
||||
|
||||
# Clean up
|
||||
|
|
|
|||
Loading…
Reference in a new issue