Apply spacing in pins files

Marlin/src/pins/pins_AZTEEG_X3.h

@@ -33,7 +33,7 @@
 #endif
 
 #if ENABLED(CASE_LIGHT_ENABLE) && !PIN_EXISTS(CASE_LIGHT)
-  #define CASE_LIGHT_PIN 6     // must define it here or else RAMPS will define it
+  #define CASE_LIGHT_PIN    6   // Define before RAMPS pins include
 #endif
 #define BOARD_NAME "Azteeg X3"
 
@@ -91,7 +91,7 @@
   #undef SCL
   #if SERVO0_PIN == 7
     #undef SERVO0_PIN
-    #def SERVO0_PIN 11
+    #define SERVO0_PIN     11
   #endif
   #define SPINDLE_LASER_PWM_PIN     7   // MUST BE HARDWARE PWM
   #define SPINDLE_LASER_ENABLE_PIN 20   // Pin should have a pullup!

Marlin/src/pins/pins_AZTEEG_X3_PRO.h

@@ -29,10 +29,9 @@
 #endif
 
 #if ENABLED(CASE_LIGHT_ENABLE) && !PIN_EXISTS(CASE_LIGHT)
-  #define CASE_LIGHT_PIN 44     // must define it here or else RAMPS will define it
+  #define CASE_LIGHT_PIN 44     // Define before RAMPS pins include
 #endif
 
-
 #define BOARD_NAME "Azteeg X3 Pro"
 
 #include "pins_RAMPS.h"
@@ -162,7 +161,7 @@
 #undef SPINDLE_LASER_ENABLE_PIN
 #undef SPINDLE_DIR_PIN
 
-#if ENABLED(SPINDLE_LASER_ENABLE)   // use EXP2 header
+#if ENABLED(SPINDLE_LASER_ENABLE)   // EXP2 header
   #if ENABLED(VIKI2) || ENABLED(miniVIKI)
     #undef BTN_EN2
     #define BTN_EN2             31   // need 7 for the spindle speed PWM

Marlin/src/pins/pins_ELEFU_3.h

@@ -122,21 +122,21 @@
   #define TLC_XLAT_PIN     22
   #define TLC_DATA_PIN     24
 
-  // We also need to define pin to port number mapping for the 2560 to match the pins listed above. If you change the TLC pins, update this as well per the 2560 datasheet!
+  // We also need to define pin to port number mapping for the 2560 to match the pins listed above.
-  // This currently only works with the RA Board.
+  // If you change the TLC pins, update this as well per the 2560 datasheet! This currently only works with the RA Board.
-  #define TLC_CLOCK_BIT 3 // bit 3 on port A
+  #define TLC_CLOCK_BIT     3
-  #define TLC_CLOCK_PORT &PORTA // bit 3 on port A
+  #define TLC_CLOCK_PORT    &PORTA
 
-  #define TLC_BLANK_BIT 1 // bit 1 on port A
+  #define TLC_BLANK_BIT     1
-  #define TLC_BLANK_PORT &PORTA // bit 1 on port A
+  #define TLC_BLANK_PORT    &PORTA
 
-  #define TLC_DATA_BIT 2 // bit 2 on port A
+  #define TLC_DATA_BIT      2
-  #define TLC_DATA_PORT &PORTA // bit 2 on port A
+  #define TLC_DATA_PORT     &PORTA
 
-  #define TLC_XLAT_BIT 0 // bit 0 on port A
+  #define TLC_XLAT_BIT      0
-  #define TLC_XLAT_PORT &PORTA // bit 0 on port A
+  #define TLC_XLAT_PORT     &PORTA
 
-  // change this to match your situation. Lots of TLCs takes up the arduino SRAM very quickly, so be careful
+  // Change this to match your situation. Lots of TLCs takes up the arduino SRAM very quickly, so be careful
   // Leave it at at least 1 if you have enabled RA_LIGHTING
   // The number of TLC5947 boards chained together for use with the animation, additional ones will repeat the animation on them, but are not individually addressable and mimic those before them. You can leave the default at 2 even if you only have 1 TLC5947 module.
   #define NUM_TLCS          2
@@ -144,6 +144,6 @@
   // These TRANS_ARRAY values let you change the order the LEDs on the lighting modules will animate for chase functions.
   // Modify them according to your specific situation.
   // NOTE: the array should be 8 long for every TLC you have. These defaults assume (2) TLCs.
-  #define TRANS_ARRAY {0, 1, 2, 3, 4, 5, 6, 7, 15, 14, 13, 12, 11, 10, 9, 8} //forwards
+  #define TRANS_ARRAY { 0, 1, 2, 3, 4, 5, 6, 7, 15, 14, 13, 12, 11, 10, 9, 8 }    // forward
-  //#define TRANS_ARRAY {7, 6, 5, 4, 3, 2, 1, 0, 8, 9, 10, 11, 12, 13, 14, 15} //backwards
+  //#define TRANS_ARRAY { 7, 6, 5, 4, 3, 2, 1, 0, 8, 9, 10, 11, 12, 13, 14, 15 }  // backward
 #endif // RA_DISCO

Marlin/src/pins/pins_GEN3_MONOLITHIC.h

@@ -98,4 +98,3 @@
 #define PS_ON_PIN          14   // Alex, does this work on the card?
 
 // Alex extras from Gen3+
-

Marlin/src/pins/pins_MELZI_CREALITY.h

@@ -48,9 +48,9 @@
 #undef FIL_RUNOUT_PIN
 
 #define LCD_SDSS           31   // Smart Controller SD card reader (rather than the Melzi)
-#define LCD_PINS_RS        28 // st9720 CS
+#define LCD_PINS_RS        28   // ST9720 CS
-#define LCD_PINS_ENABLE    17 // st9720 DAT
+#define LCD_PINS_ENABLE    17   // ST9720 DAT
-#define LCD_PINS_D4        30 // st9720 CLK
+#define LCD_PINS_D4        30   // ST9720 CLK
 #define FIL_RUNOUT_PIN     -1   // Uses Beeper/LED Pin Pulled to GND
 
 // Alter timing for graphical display

Marlin/src/pins/pins_MELZI_MALYAN.h

@@ -35,9 +35,9 @@
 #undef BTN_EN2
 #undef BTN_ENC
 
-#define LCD_PINS_RS     17 // st9720 CS
+#define LCD_PINS_RS        17   // ST9720 CS
-#define LCD_PINS_ENABLE 16 // st9720 DAT
+#define LCD_PINS_ENABLE    16   // ST9720 DAT
-#define LCD_PINS_D4     11 // st9720 CLK
+#define LCD_PINS_D4        11   // ST9720 CLK
 #define BTN_EN1            30
 #define BTN_EN2            29
 #define BTN_ENC            28

Marlin/src/pins/pins_MIGHTYBOARD_REVE.h

@@ -272,8 +272,6 @@
 #define SPINDLE_DIR_PIN          67   // K5
 
 
-
-
 // Check if all pins are defined in mega/pins_arduino.h
 #include <Arduino.h>
 static_assert(NUM_DIGITAL_PINS > MAX_PIN, "add missing pins to [arduino dir]/hardware/arduino/avr/variants/mega/pins_arduino.h based on fastio.h"

Marlin/src/pins/pins_MINITRONICS.h

@@ -136,7 +136,7 @@
   #define HEATER_BED_PIN      4   // won't compile
   #define TEMP_BED_PIN       50
   #define TEMP_0_PIN         51
-  #define SPINDLE_LASER_ENABLE_PIN      52 // using A6 because it already has a pull up on it
+  #define SPINDLE_LASER_ENABLE_PIN      52   // using A6 because it already has a pullup
   #define SPINDLE_LASER_PWM_PIN          3   // WARNING - LED & resistor pull up to +12/+24V stepper voltage
   #define SPINDLE_DIR_PIN               53
 #endif

Marlin/src/pins/pins_RAMPS.h

@@ -44,17 +44,9 @@
  *         7 | 11
  */
 
-#if ENABLED(TARGET_LPC1768)
-  #error "Oops!  Set MOTHERBOARD to an LPC1768-based board when building for LPC1768."
-#elif defined(__STM32F1__)
-  #error "Oops!  Set MOTHERBOARD to an STM32F1-based board when building for STM32F1."
-#endif
-
-#if DISABLED(IS_RAMPS_SMART) && DISABLED(IS_RAMPS_DUO) && DISABLED(IS_RAMPS4DUE) && DISABLED(TARGET_LPC1768)
 #if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__)
   #error "Oops!  Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu."
 #endif
-#endif
 
 #ifndef BOARD_NAME
   #define BOARD_NAME "RAMPS 1.4"
@@ -547,10 +539,6 @@
 
       #define ADC_KEYPAD_PIN    12
 
-    #elif ENABLED(AZSMZ_12864)
-
-      // Pins only defined for RAMPS_SMART currently
-
     #else
 
       // Beeper on AUX-4

Marlin/src/pins/pins_RAMPS_RE_ARM.h

@@ -129,7 +129,6 @@
 //#define ??               6   // A6 - ( 0)  - RXD0 - J4-4 & AUX-1
 #define FILWIDTH_PIN       7   // A7 - ( 1)  - TXD0 - J4-5 & AUX-1
 
-
 //
 // Augmentation for auto-assigning RAMPS plugs
 //

Marlin/src/pins/pins_STM32F1R.h

@@ -280,4 +280,3 @@
 #define U_MIN_PIN          -1
 #define V_MIN_PIN          -1
 #define W_MIN_PIN          -1
-

Marlin/src/pins/pins_STM3R_MINI.h

@@ -289,4 +289,3 @@
 #define U_MIN_PIN          -1
 #define V_MIN_PIN          -1
 #define W_MIN_PIN          -1
-

Marlin/src/pins/pins_THE_BORG.h

@@ -72,7 +72,7 @@
 //
 #define STEPPER_ENABLE_PIN _STM32_PIN(PORTE,  0)
 
-#define X_STEP_PIN         _STM32_PIN(PORTC, 6) //96, 39 in arduino
+#define X_STEP_PIN         _STM32_PIN(PORTC,  6)   // 96, 39 in Arduino
 #define X_DIR_PIN          _STM32_PIN(PORTC,  7)
 #define X_ENABLE_PIN       _STM32_PIN(PORTC,  8)
 
@@ -147,8 +147,8 @@
 // Misc. Functions
 //
 
-//#define CASE_LIGHT_PIN_CI _STM32_PIN(PORTF, 13)  //
+//#define CASE_LIGHT_PIN_CI _STM32_PIN(PORTF, 13)
-//#define CASE_LIGHT_PIN_DO _STM32_PIN(PORTF, 14)  //
+//#define CASE_LIGHT_PIN_DO _STM32_PIN(PORTF, 14)
 //#define NEOPIXEL_PIN     _STM32_PIN(PORTF, 13)
 
 //

Marlin/src/pins/pins_ULTIMAKER.h

@@ -43,7 +43,7 @@
 //
 // Servos
 //
-#define SERVO0_PIN         13 // untested
+#define SERVO0_PIN         13   // UNTESTED
 
 //
 // Limit Switches