diff --git a/Marlin/src/HAL/DUE/fastio/G2_PWM.cpp b/Marlin/src/HAL/DUE/fastio/G2_PWM.cpp index 1682faea66..d9fbabce21 100644 --- a/Marlin/src/HAL/DUE/fastio/G2_PWM.cpp +++ b/Marlin/src/HAL/DUE/fastio/G2_PWM.cpp @@ -154,7 +154,7 @@ void Stepper::digipot_init() { NVIC_SetPriority(PWM_IRQn, NVIC_EncodePriority(0, 10, 0)); // normal priority for PWM module (can stand some jitter on the Vref signals) } -void Stepper::digipot_current(const uint8_t driver, const int16_t current) { +void Stepper::set_digipot_current(const uint8_t driver, const int16_t current) { if (!(PWM->PWM_CH_NUM[0].PWM_CPRD == PWM_PERIOD_US)) digipot_init(); // Init PWM system if needed diff --git a/Marlin/src/HAL/LPC1768/inc/SanityCheck.h b/Marlin/src/HAL/LPC1768/inc/SanityCheck.h index fd82e2884a..f5051d32a1 100644 --- a/Marlin/src/HAL/LPC1768/inc/SanityCheck.h +++ b/Marlin/src/HAL/LPC1768/inc/SanityCheck.h @@ -191,7 +191,7 @@ static_assert(DISABLED(BAUD_RATE_GCODE), "BAUD_RATE_GCODE is not yet supported o // // Flag any i2c pin conflicts // -#if ANY(HAS_I2C_DIGIPOT, DAC_STEPPER_CURRENT, EXPERIMENTAL_I2CBUS, I2C_POSITION_ENCODERS, PCA9632, I2C_EEPROM) +#if ANY(HAS_MOTOR_CURRENT_I2C, HAS_MOTOR_CURRENT_DAC, EXPERIMENTAL_I2CBUS, I2C_POSITION_ENCODERS, PCA9632, I2C_EEPROM) #define USEDI2CDEV_M 1 // /Wire.cpp #if USEDI2CDEV_M == 0 // P0_27 [D57] (AUX-1) .......... P0_28 [D58] (AUX-1) diff --git a/Marlin/src/MarlinCore.cpp b/Marlin/src/MarlinCore.cpp index 672858d05a..3a20cf3ee3 100644 --- a/Marlin/src/MarlinCore.cpp +++ b/Marlin/src/MarlinCore.cpp @@ -97,7 +97,7 @@ #include "feature/closedloop.h" #endif -#if HAS_I2C_DIGIPOT +#if HAS_MOTOR_CURRENT_I2C #include "feature/digipot/digipot.h" #endif @@ -125,7 +125,7 @@ #include "module/servo.h" #endif -#if ENABLED(DAC_STEPPER_CURRENT) +#if ENABLED(HAS_MOTOR_CURRENT_DAC) #include "feature/dac/stepper_dac.h" #endif @@ -1137,12 +1137,12 @@ void setup() { SETUP_RUN(enableStepperDrivers()); #endif - #if HAS_I2C_DIGIPOT - SETUP_RUN(digipot_i2c_init()); + #if HAS_MOTOR_CURRENT_I2C + SETUP_RUN(digipot_i2c.init()); #endif - #if ENABLED(DAC_STEPPER_CURRENT) - SETUP_RUN(dac_init()); + #if ENABLED(HAS_MOTOR_CURRENT_DAC) + SETUP_RUN(stepper_dac.init()); #endif #if EITHER(Z_PROBE_SLED, SOLENOID_PROBE) && HAS_SOLENOID_1 diff --git a/Marlin/src/feature/dac/dac_mcp4728.cpp b/Marlin/src/feature/dac/dac_mcp4728.cpp index 55f10a49ef..81c465cf29 100644 --- a/Marlin/src/feature/dac/dac_mcp4728.cpp +++ b/Marlin/src/feature/dac/dac_mcp4728.cpp @@ -32,16 +32,18 @@ #include "../../inc/MarlinConfig.h" -#if ENABLED(DAC_STEPPER_CURRENT) +#if ENABLED(HAS_MOTOR_CURRENT_DAC) #include "dac_mcp4728.h" -xyze_uint_t mcp4728_values; +MCP4728 mcp4728; + +xyze_uint_t dac_values; /** * Begin I2C, get current values (input register and eeprom) of mcp4728 */ -void mcp4728_init() { +void MCP4728::init() { Wire.begin(); Wire.requestFrom(I2C_ADDRESS(DAC_DEV_ADDRESS), uint8_t(24)); while (Wire.available()) { @@ -50,7 +52,7 @@ void mcp4728_init() { loByte = Wire.read(); if (!(deviceID & 0x08)) - mcp4728_values[(deviceID & 0x30) >> 4] = word((hiByte & 0x0F), loByte); + dac_values[(deviceID & 0x30) >> 4] = word((hiByte & 0x0F), loByte); } } @@ -58,9 +60,9 @@ void mcp4728_init() { * Write input resister value to specified channel using fastwrite method. * Channel : 0-3, Values : 0-4095 */ -uint8_t mcp4728_analogWrite(const uint8_t channel, const uint16_t value) { - mcp4728_values[channel] = value; - return mcp4728_fastWrite(); +uint8_t MCP4728::analogWrite(const uint8_t channel, const uint16_t value) { + dac_values[channel] = value; + return fastWrite(); } /** @@ -68,12 +70,12 @@ uint8_t mcp4728_analogWrite(const uint8_t channel, const uint16_t value) { * This will update both input register and EEPROM value * This will also write current Vref, PowerDown, Gain settings to EEPROM */ -uint8_t mcp4728_eepromWrite() { +uint8_t MCP4728::eepromWrite() { Wire.beginTransmission(I2C_ADDRESS(DAC_DEV_ADDRESS)); Wire.write(SEQWRITE); LOOP_XYZE(i) { - Wire.write(DAC_STEPPER_VREF << 7 | DAC_STEPPER_GAIN << 4 | highByte(mcp4728_values[i])); - Wire.write(lowByte(mcp4728_values[i])); + Wire.write(DAC_STEPPER_VREF << 7 | DAC_STEPPER_GAIN << 4 | highByte(dac_values[i])); + Wire.write(lowByte(dac_values[i])); } return Wire.endTransmission(); } @@ -81,7 +83,7 @@ uint8_t mcp4728_eepromWrite() { /** * Write Voltage reference setting to all input regiters */ -uint8_t mcp4728_setVref_all(const uint8_t value) { +uint8_t MCP4728::setVref_all(const uint8_t value) { Wire.beginTransmission(I2C_ADDRESS(DAC_DEV_ADDRESS)); Wire.write(VREFWRITE | (value ? 0x0F : 0x00)); return Wire.endTransmission(); @@ -89,7 +91,7 @@ uint8_t mcp4728_setVref_all(const uint8_t value) { /** * Write Gain setting to all input regiters */ -uint8_t mcp4728_setGain_all(const uint8_t value) { +uint8_t MCP4728::setGain_all(const uint8_t value) { Wire.beginTransmission(I2C_ADDRESS(DAC_DEV_ADDRESS)); Wire.write(GAINWRITE | (value ? 0x0F : 0x00)); return Wire.endTransmission(); @@ -98,16 +100,16 @@ uint8_t mcp4728_setGain_all(const uint8_t value) { /** * Return Input Register value */ -uint16_t mcp4728_getValue(const uint8_t channel) { return mcp4728_values[channel]; } +uint16_t MCP4728::getValue(const uint8_t channel) { return dac_values[channel]; } #if 0 /** * Steph: Might be useful in the future * Return Vout */ -uint16_t mcp4728_getVout(const uint8_t channel) { +uint16_t MCP4728::getVout(const uint8_t channel) { const uint32_t vref = 2048, - vOut = (vref * mcp4728_values[channel] * (_DAC_STEPPER_GAIN + 1)) / 4096; + vOut = (vref * dac_values[channel] * (_DAC_STEPPER_GAIN + 1)) / 4096; return _MIN(vOut, defaultVDD); } #endif @@ -115,15 +117,15 @@ uint16_t mcp4728_getVout(const uint8_t channel) { /** * Returns DAC values as a 0-100 percentage of drive strength */ -uint8_t mcp4728_getDrvPct(const uint8_t channel) { return uint8_t(100.0 * mcp4728_values[channel] / (DAC_STEPPER_MAX) + 0.5); } +uint8_t MCP4728::getDrvPct(const uint8_t channel) { return uint8_t(100.0 * dac_values[channel] / (DAC_STEPPER_MAX) + 0.5); } /** * Receives all Drive strengths as 0-100 percent values, updates * DAC Values array and calls fastwrite to update the DAC. */ -void mcp4728_setDrvPct(xyze_uint8_t &pct) { - mcp4728_values *= 0.01 * pct * (DAC_STEPPER_MAX); - mcp4728_fastWrite(); +void MCP4728::setDrvPct(xyze_uint8_t &pct) { + dac_values *= 0.01 * pct * (DAC_STEPPER_MAX); + fastWrite(); } /** @@ -131,11 +133,11 @@ void mcp4728_setDrvPct(xyze_uint8_t &pct) { * DAC Input and PowerDown bits update. * No EEPROM update */ -uint8_t mcp4728_fastWrite() { +uint8_t MCP4728::fastWrite() { Wire.beginTransmission(I2C_ADDRESS(DAC_DEV_ADDRESS)); LOOP_XYZE(i) { - Wire.write(highByte(mcp4728_values[i])); - Wire.write(lowByte(mcp4728_values[i])); + Wire.write(highByte(dac_values[i])); + Wire.write(lowByte(dac_values[i])); } return Wire.endTransmission(); } @@ -143,10 +145,10 @@ uint8_t mcp4728_fastWrite() { /** * Common function for simple general commands */ -uint8_t mcp4728_simpleCommand(const byte simpleCommand) { +uint8_t MCP4728::simpleCommand(const byte simpleCommand) { Wire.beginTransmission(I2C_ADDRESS(GENERALCALL)); Wire.write(simpleCommand); return Wire.endTransmission(); } -#endif // DAC_STEPPER_CURRENT +#endif // HAS_MOTOR_CURRENT_DAC diff --git a/Marlin/src/feature/dac/dac_mcp4728.h b/Marlin/src/feature/dac/dac_mcp4728.h index fc69bd8ff4..571716d483 100644 --- a/Marlin/src/feature/dac/dac_mcp4728.h +++ b/Marlin/src/feature/dac/dac_mcp4728.h @@ -65,13 +65,18 @@ // DAC_OR_ADDRESS defined in pins_BOARD.h file #define DAC_DEV_ADDRESS (BASE_ADDR | DAC_OR_ADDRESS) -void mcp4728_init(); -uint8_t mcp4728_analogWrite(const uint8_t channel, const uint16_t value); -uint8_t mcp4728_eepromWrite(); -uint8_t mcp4728_setVref_all(const uint8_t value); -uint8_t mcp4728_setGain_all(const uint8_t value); -uint16_t mcp4728_getValue(const uint8_t channel); -uint8_t mcp4728_fastWrite(); -uint8_t mcp4728_simpleCommand(const byte simpleCommand); -uint8_t mcp4728_getDrvPct(const uint8_t channel); -void mcp4728_setDrvPct(xyze_uint8_t &pct); +class MCP4728 { +public: + static void init(); + static uint8_t analogWrite(const uint8_t channel, const uint16_t value); + static uint8_t eepromWrite(); + static uint8_t setVref_all(const uint8_t value); + static uint8_t setGain_all(const uint8_t value); + static uint16_t getValue(const uint8_t channel); + static uint8_t fastWrite(); + static uint8_t simpleCommand(const byte simpleCommand); + static uint8_t getDrvPct(const uint8_t channel); + static void setDrvPct(xyze_uint8_t &pct); +}; + +extern MCP4728 mcp4728; diff --git a/Marlin/src/feature/dac/stepper_dac.cpp b/Marlin/src/feature/dac/stepper_dac.cpp index 6b140a0025..5f10b4ccfb 100644 --- a/Marlin/src/feature/dac/stepper_dac.cpp +++ b/Marlin/src/feature/dac/stepper_dac.cpp @@ -26,7 +26,7 @@ #include "../../inc/MarlinConfig.h" -#if ENABLED(DAC_STEPPER_CURRENT) +#if ENABLED(HAS_MOTOR_CURRENT_DAC) #include "stepper_dac.h" #include "../../MarlinCore.h" // for SP_X_LBL... @@ -35,56 +35,53 @@ bool dac_present = false; constexpr xyze_uint8_t dac_order = DAC_STEPPER_ORDER; xyze_uint8_t dac_channel_pct = DAC_MOTOR_CURRENT_DEFAULT; -int dac_init() { +StepperDAC stepper_dac; + +int StepperDAC::init() { #if PIN_EXISTS(DAC_DISABLE) OUT_WRITE(DAC_DISABLE_PIN, LOW); // set pin low to enable DAC #endif - mcp4728_init(); + mcp4728.init(); - if (mcp4728_simpleCommand(RESET)) return -1; + if (mcp4728.simpleCommand(RESET)) return -1; dac_present = true; - mcp4728_setVref_all(DAC_STEPPER_VREF); - mcp4728_setGain_all(DAC_STEPPER_GAIN); + mcp4728.setVref_all(DAC_STEPPER_VREF); + mcp4728.setGain_all(DAC_STEPPER_GAIN); - if (mcp4728_getDrvPct(0) < 1 || mcp4728_getDrvPct(1) < 1 || mcp4728_getDrvPct(2) < 1 || mcp4728_getDrvPct(3) < 1 ) { - mcp4728_setDrvPct(dac_channel_pct); - mcp4728_eepromWrite(); + if (mcp4728.getDrvPct(0) < 1 || mcp4728.getDrvPct(1) < 1 || mcp4728.getDrvPct(2) < 1 || mcp4728.getDrvPct(3) < 1 ) { + mcp4728.setDrvPct(dac_channel_pct); + mcp4728.eepromWrite(); } return 0; } -void dac_current_percent(uint8_t channel, float val) { - if (!dac_present) return; - - NOMORE(val, 100); - - mcp4728_analogWrite(dac_order[channel], val * 0.01 * (DAC_STEPPER_MAX)); - mcp4728_simpleCommand(UPDATE); -} - -void dac_current_raw(uint8_t channel, uint16_t val) { +void StepperDAC::set_current_value(const uint8_t channel, uint16_t val) { if (!dac_present) return; NOMORE(val, uint16_t(DAC_STEPPER_MAX)); - mcp4728_analogWrite(dac_order[channel], val); - mcp4728_simpleCommand(UPDATE); + mcp4728.analogWrite(dac_order[channel], val); + mcp4728.simpleCommand(UPDATE); } -static float dac_perc(int8_t n) { return 100.0 * mcp4728_getValue(dac_order[n]) * RECIPROCAL(DAC_STEPPER_MAX); } -static float dac_amps(int8_t n) { return mcp4728_getDrvPct(dac_order[n]) * (DAC_STEPPER_MAX) * 0.125 * RECIPROCAL(DAC_STEPPER_SENSE); } +void StepperDAC::set_current_percent(const uint8_t channel, float val) { + set_current_value(channel, _MIN(val, 100.0f) * (DAC_STEPPER_MAX) / 100.0f); +} -uint8_t dac_current_get_percent(const AxisEnum axis) { return mcp4728_getDrvPct(dac_order[axis]); } -void dac_current_set_percents(xyze_uint8_t &pct) { +static float dac_perc(int8_t n) { return 100.0 * mcp4728.getValue(dac_order[n]) * RECIPROCAL(DAC_STEPPER_MAX); } +static float dac_amps(int8_t n) { return mcp4728.getDrvPct(dac_order[n]) * (DAC_STEPPER_MAX) * 0.125 * RECIPROCAL(DAC_STEPPER_SENSE); } + +uint8_t StepperDAC::get_current_percent(const AxisEnum axis) { return mcp4728.getDrvPct(dac_order[axis]); } +void StepperDAC::set_current_percents(xyze_uint8_t &pct) { LOOP_XYZE(i) dac_channel_pct[i] = pct[dac_order[i]]; - mcp4728_setDrvPct(dac_channel_pct); + mcp4728.setDrvPct(dac_channel_pct); } -void dac_print_values() { +void StepperDAC::print_values() { if (!dac_present) return; SERIAL_ECHO_MSG("Stepper current values in % (Amps):"); SERIAL_ECHO_START(); @@ -94,9 +91,9 @@ void dac_print_values() { SERIAL_ECHOLNPAIR_P(SP_E_LBL, dac_perc(E_AXIS), PSTR(" ("), dac_amps(E_AXIS), PSTR(")")); } -void dac_commit_eeprom() { +void StepperDAC::commit_eeprom() { if (!dac_present) return; - mcp4728_eepromWrite(); + mcp4728.eepromWrite(); } -#endif // DAC_STEPPER_CURRENT +#endif // HAS_MOTOR_CURRENT_DAC diff --git a/Marlin/src/feature/dac/stepper_dac.h b/Marlin/src/feature/dac/stepper_dac.h index 0543b6275e..6836335e98 100644 --- a/Marlin/src/feature/dac/stepper_dac.h +++ b/Marlin/src/feature/dac/stepper_dac.h @@ -27,10 +27,15 @@ #include "dac_mcp4728.h" -int dac_init(); -void dac_current_percent(uint8_t channel, float val); -void dac_current_raw(uint8_t channel, uint16_t val); -void dac_print_values(); -void dac_commit_eeprom(); -uint8_t dac_current_get_percent(AxisEnum axis); -void dac_current_set_percents(xyze_uint8_t &pct); +class StepperDAC { +public: + static int init(); + static void set_current_percent(const uint8_t channel, float val); + static void set_current_value(const uint8_t channel, uint16_t val); + static void print_values(); + static void commit_eeprom(); + static uint8_t get_current_percent(AxisEnum axis); + static void set_current_percents(xyze_uint8_t &pct); +}; + +extern StepperDAC stepper_dac; diff --git a/Marlin/src/feature/digipot/digipot.h b/Marlin/src/feature/digipot/digipot.h index d59f8b930a..c53f8093dd 100644 --- a/Marlin/src/feature/digipot/digipot.h +++ b/Marlin/src/feature/digipot/digipot.h @@ -21,5 +21,13 @@ */ #pragma once -void digipot_i2c_set_current(const uint8_t channel, const float current); -void digipot_i2c_init(); +// +// Header for MCP4018 and MCP4451 current control i2c devices +// +class DigipotI2C { +public: + static void init(); + static void set_current(const uint8_t channel, const float current); +}; + +DigipotI2C digipot_i2c; diff --git a/Marlin/src/feature/digipot/digipot_mcp4018.cpp b/Marlin/src/feature/digipot/digipot_mcp4018.cpp index 35c513a32c..6260185fc3 100644 --- a/Marlin/src/feature/digipot/digipot_mcp4018.cpp +++ b/Marlin/src/feature/digipot/digipot_mcp4018.cpp @@ -24,6 +24,8 @@ #if ENABLED(DIGIPOT_MCP4018) +#include "digipot.h" + #include #include // https://github.com/stawel/SlowSoftI2CMaster @@ -68,7 +70,7 @@ static SlowSoftI2CMaster pots[DIGIPOT_I2C_NUM_CHANNELS] = { #endif }; -static void i2c_send(const uint8_t channel, const byte v) { +static void digipot_i2c_send(const uint8_t channel, const byte v) { if (WITHIN(channel, 0, DIGIPOT_I2C_NUM_CHANNELS - 1)) { pots[channel].i2c_start(((DIGIPOT_I2C_ADDRESS_A) << 1) | I2C_WRITE); pots[channel].i2c_write(v); @@ -77,12 +79,12 @@ static void i2c_send(const uint8_t channel, const byte v) { } // This is for the MCP4018 I2C based digipot -void digipot_i2c_set_current(const uint8_t channel, const float current) { +void DigipotI2C::set_current(const uint8_t channel, const float current) { const float ival = _MIN(_MAX(current, 0), float(DIGIPOT_MCP4018_MAX_VALUE)); - i2c_send(channel, current_to_wiper(ival)); + digipot_i2c_send(channel, current_to_wiper(ival)); } -void digipot_i2c_init() { +void DigipotI2C::init() { LOOP_L_N(i, DIGIPOT_I2C_NUM_CHANNELS) pots[i].i2c_init(); // Init currents according to Configuration_adv.h @@ -94,7 +96,7 @@ void digipot_i2c_init() { #endif ; LOOP_L_N(i, COUNT(digipot_motor_current)) - digipot_i2c_set_current(i, pgm_read_float(&digipot_motor_current[i])); + set_current(i, pgm_read_float(&digipot_motor_current[i])); } #endif // DIGIPOT_MCP4018 diff --git a/Marlin/src/feature/digipot/digipot_mcp4451.cpp b/Marlin/src/feature/digipot/digipot_mcp4451.cpp index 0c8ff04a0b..7e6ace49a0 100644 --- a/Marlin/src/feature/digipot/digipot_mcp4451.cpp +++ b/Marlin/src/feature/digipot/digipot_mcp4451.cpp @@ -24,6 +24,8 @@ #if ENABLED(DIGIPOT_MCP4451) +#include "digipot.h" + #include #include @@ -61,7 +63,7 @@ static void digipot_i2c_send(const byte addr, const byte a, const byte b) { } // This is for the MCP4451 I2C based digipot -void digipot_i2c_set_current(const uint8_t channel, const float current) { +void DigipotI2C::set_current(const uint8_t channel, const float current) { // These addresses are specific to Azteeg X3 Pro, can be set to others. // In this case first digipot is at address A0=0, A1=0, second one is at A0=0, A1=1 const byte addr = channel < 4 ? DIGIPOT_I2C_ADDRESS_A : DIGIPOT_I2C_ADDRESS_B; // channel 0-3 vs 4-7 @@ -75,7 +77,7 @@ void digipot_i2c_set_current(const uint8_t channel, const float current) { digipot_i2c_send(addr, addresses[channel & 0x3], current_to_wiper(_MIN(float(_MAX(current, 0)), DIGIPOT_I2C_MAX_CURRENT))); } -void digipot_i2c_init() { +void DigipotI2C::init() { #if MB(MKS_SBASE) configure_i2c(16); // Set clock_option to 16 ensure I2C is initialized at 400kHz #else @@ -90,7 +92,7 @@ void digipot_i2c_init() { #endif ; LOOP_L_N(i, COUNT(digipot_motor_current)) - digipot_i2c_set_current(i, pgm_read_float(&digipot_motor_current[i])); + set_current(i, pgm_read_float(&digipot_motor_current[i])); } #endif // DIGIPOT_MCP4451 diff --git a/Marlin/src/gcode/feature/digipot/M907-M910.cpp b/Marlin/src/gcode/feature/digipot/M907-M910.cpp index 54599a0451..e463666207 100644 --- a/Marlin/src/gcode/feature/digipot/M907-M910.cpp +++ b/Marlin/src/gcode/feature/digipot/M907-M910.cpp @@ -22,19 +22,19 @@ #include "../../../inc/MarlinConfig.h" -#if ANY(HAS_DIGIPOTSS, HAS_MOTOR_CURRENT_PWM, HAS_I2C_DIGIPOT, DAC_STEPPER_CURRENT) +#if ANY(HAS_MOTOR_CURRENT_SPI, HAS_MOTOR_CURRENT_PWM, HAS_MOTOR_CURRENT_I2C, HAS_MOTOR_CURRENT_DAC) #include "../../gcode.h" -#if HAS_DIGIPOTSS || HAS_MOTOR_CURRENT_PWM +#if HAS_MOTOR_CURRENT_SPI || HAS_MOTOR_CURRENT_PWM #include "../../../module/stepper.h" #endif -#if HAS_I2C_DIGIPOT +#if HAS_MOTOR_CURRENT_I2C #include "../../../feature/digipot/digipot.h" #endif -#if ENABLED(DAC_STEPPER_CURRENT) +#if ENABLED(HAS_MOTOR_CURRENT_DAC) #include "../../../feature/dac/stepper_dac.h" #endif @@ -42,61 +42,61 @@ * M907: Set digital trimpot motor current using axis codes X, Y, Z, E, B, S */ void GcodeSuite::M907() { - #if HAS_DIGIPOTSS + #if HAS_MOTOR_CURRENT_SPI - LOOP_XYZE(i) if (parser.seenval(axis_codes[i])) stepper.digipot_current(i, parser.value_int()); - if (parser.seenval('B')) stepper.digipot_current(4, parser.value_int()); - if (parser.seenval('S')) LOOP_LE_N(i, 4) stepper.digipot_current(i, parser.value_int()); + LOOP_XYZE(i) if (parser.seenval(axis_codes[i])) stepper.set_digipot_current(i, parser.value_int()); + if (parser.seenval('B')) stepper.set_digipot_current(4, parser.value_int()); + if (parser.seenval('S')) LOOP_LE_N(i, 4) stepper.set_digipot_current(i, parser.value_int()); #elif HAS_MOTOR_CURRENT_PWM #if ANY_PIN(MOTOR_CURRENT_PWM_X, MOTOR_CURRENT_PWM_Y, MOTOR_CURRENT_PWM_XY) - if (parser.seenval('X') || parser.seenval('Y')) stepper.digipot_current(0, parser.value_int()); + if (parser.seenval('X') || parser.seenval('Y')) stepper.set_digipot_current(0, parser.value_int()); #endif #if PIN_EXISTS(MOTOR_CURRENT_PWM_Z) - if (parser.seenval('Z')) stepper.digipot_current(1, parser.value_int()); + if (parser.seenval('Z')) stepper.set_digipot_current(1, parser.value_int()); #endif #if PIN_EXISTS(MOTOR_CURRENT_PWM_E) - if (parser.seenval('E')) stepper.digipot_current(2, parser.value_int()); + if (parser.seenval('E')) stepper.set_digipot_current(2, parser.value_int()); #endif #endif - #if HAS_I2C_DIGIPOT + #if HAS_MOTOR_CURRENT_I2C // this one uses actual amps in floating point - LOOP_XYZE(i) if (parser.seenval(axis_codes[i])) digipot_i2c_set_current(i, parser.value_float()); + LOOP_XYZE(i) if (parser.seenval(axis_codes[i])) digipot_i2c.set_current(i, parser.value_float()); // Additional extruders use B,C,D for channels 4,5,6. // TODO: Change these parameters because 'E' is used. B? for (uint8_t i = E_AXIS + 1; i < DIGIPOT_I2C_NUM_CHANNELS; i++) - if (parser.seenval('B' + i - (E_AXIS + 1))) digipot_i2c_set_current(i, parser.value_float()); + if (parser.seenval('B' + i - (E_AXIS + 1))) digipot_i2c.set_current(i, parser.value_float()); #endif - #if ENABLED(DAC_STEPPER_CURRENT) + #if ENABLED(HAS_MOTOR_CURRENT_DAC) if (parser.seenval('S')) { const float dac_percent = parser.value_float(); - LOOP_LE_N(i, 4) dac_current_percent(i, dac_percent); + LOOP_LE_N(i, 4) stepper_dac.set_current_percent(i, dac_percent); } - LOOP_XYZE(i) if (parser.seenval(axis_codes[i])) dac_current_percent(i, parser.value_float()); + LOOP_XYZE(i) if (parser.seenval(axis_codes[i])) stepper_dac.set_current_percent(i, parser.value_float()); #endif } -#if EITHER(HAS_DIGIPOTSS, DAC_STEPPER_CURRENT) +#if EITHER(HAS_MOTOR_CURRENT_SPI, HAS_MOTOR_CURRENT_DAC) /** * M908: Control digital trimpot directly (M908 P S) */ void GcodeSuite::M908() { - TERN_(HAS_DIGIPOTSS, stepper.digitalPotWrite(parser.intval('P'), parser.intval('S'))); - TERN_(DAC_STEPPER_CURRENT, dac_current_raw(parser.byteval('P', -1), parser.ushortval('S', 0))); + TERN_(HAS_MOTOR_CURRENT_SPI, stepper.set_digipot_value_spi(parser.intval('P'), parser.intval('S'))); + TERN_(HAS_MOTOR_CURRENT_DAC, stepper_dac.set_current_value(parser.byteval('P', -1), parser.ushortval('S', 0))); } -#endif // HAS_DIGIPOTSS || DAC_STEPPER_CURRENT + #if ENABLED(HAS_MOTOR_CURRENT_DAC) -#if ENABLED(DAC_STEPPER_CURRENT) + void GcodeSuite::M909() { stepper_dac.print_values(); } + void GcodeSuite::M910() { stepper_dac.commit_eeprom(); } - void GcodeSuite::M909() { dac_print_values(); } - void GcodeSuite::M910() { dac_commit_eeprom(); } + #endif // HAS_MOTOR_CURRENT_DAC -#endif // DAC_STEPPER_CURRENT +#endif // HAS_MOTOR_CURRENT_SPI || HAS_MOTOR_CURRENT_DAC -#endif // HAS_DIGIPOTSS || HAS_MOTOR_CURRENT_PWM || HAS_I2C_DIGIPOT || DAC_STEPPER_CURRENT +#endif // HAS_MOTOR_CURRENT_SPI || HAS_MOTOR_CURRENT_PWM || HAS_MOTOR_CURRENT_I2C || HAS_MOTOR_CURRENT_DAC diff --git a/Marlin/src/gcode/gcode.cpp b/Marlin/src/gcode/gcode.cpp index cbf62e0fcf..1d4e8f9d4d 100644 --- a/Marlin/src/gcode/gcode.cpp +++ b/Marlin/src/gcode/gcode.cpp @@ -823,11 +823,11 @@ void GcodeSuite::process_parsed_command(const bool no_ok/*=false*/) { case 900: M900(); break; // M900: Set advance K factor. #endif - #if ANY(HAS_DIGIPOTSS, HAS_MOTOR_CURRENT_PWM, HAS_I2C_DIGIPOT, DAC_STEPPER_CURRENT) + #if ANY(HAS_MOTOR_CURRENT_SPI, HAS_MOTOR_CURRENT_PWM, HAS_MOTOR_CURRENT_I2C, HAS_MOTOR_CURRENT_DAC) case 907: M907(); break; // M907: Set digital trimpot motor current using axis codes. - #if EITHER(HAS_DIGIPOTSS, DAC_STEPPER_CURRENT) + #if EITHER(HAS_MOTOR_CURRENT_SPI, HAS_MOTOR_CURRENT_DAC) case 908: M908(); break; // M908: Control digital trimpot directly. - #if ENABLED(DAC_STEPPER_CURRENT) + #if ENABLED(HAS_MOTOR_CURRENT_DAC) case 909: M909(); break; // M909: Print digipot/DAC current value case 910: M910(); break; // M910: Commit digipot/DAC value to external EEPROM #endif diff --git a/Marlin/src/gcode/gcode.h b/Marlin/src/gcode/gcode.h index 73a3727813..683642bec6 100644 --- a/Marlin/src/gcode/gcode.h +++ b/Marlin/src/gcode/gcode.h @@ -258,9 +258,9 @@ * M900 - Get or Set Linear Advance K-factor. (Requires LIN_ADVANCE) * M906 - Set or get motor current in milliamps using axis codes X, Y, Z, E. Report values if no axis codes given. (Requires at least one _DRIVER_TYPE defined as TMC2130/2160/5130/5160/2208/2209/2660 or L6470) * M907 - Set digital trimpot motor current using axis codes. (Requires a board with digital trimpots) - * M908 - Control digital trimpot directly. (Requires DAC_STEPPER_CURRENT or DIGIPOTSS_PIN) - * M909 - Print digipot/DAC current value. (Requires DAC_STEPPER_CURRENT) - * M910 - Commit digipot/DAC value to external EEPROM via I2C. (Requires DAC_STEPPER_CURRENT) + * M908 - Control digital trimpot directly. (Requires HAS_MOTOR_CURRENT_DAC or DIGIPOTSS_PIN) + * M909 - Print digipot/DAC current value. (Requires HAS_MOTOR_CURRENT_DAC) + * M910 - Commit digipot/DAC value to external EEPROM via I2C. (Requires HAS_MOTOR_CURRENT_DAC) * M911 - Report stepper driver overtemperature pre-warn condition. (Requires at least one _DRIVER_TYPE defined as TMC2130/2160/5130/5160/2208/2209/2660) * M912 - Clear stepper driver overtemperature pre-warn condition flag. (Requires at least one _DRIVER_TYPE defined as TMC2130/2160/5130/5160/2208/2209/2660) * M913 - Set HYBRID_THRESHOLD speed. (Requires HYBRID_THRESHOLD) @@ -847,11 +847,11 @@ private: static void M918(); #endif - #if ANY(HAS_DIGIPOTSS, HAS_MOTOR_CURRENT_PWM, HAS_I2C_DIGIPOT, DAC_STEPPER_CURRENT) + #if ANY(HAS_MOTOR_CURRENT_SPI, HAS_MOTOR_CURRENT_PWM, HAS_MOTOR_CURRENT_I2C, HAS_MOTOR_CURRENT_DAC) static void M907(); - #if EITHER(HAS_DIGIPOTSS, DAC_STEPPER_CURRENT) + #if EITHER(HAS_MOTOR_CURRENT_SPI, HAS_MOTOR_CURRENT_DAC) static void M908(); - #if ENABLED(DAC_STEPPER_CURRENT) + #if ENABLED(HAS_MOTOR_CURRENT_DAC) static void M909(); static void M910(); #endif diff --git a/Marlin/src/inc/Conditionals_adv.h b/Marlin/src/inc/Conditionals_adv.h index 0952148d19..255470bca6 100644 --- a/Marlin/src/inc/Conditionals_adv.h +++ b/Marlin/src/inc/Conditionals_adv.h @@ -175,7 +175,7 @@ #endif #if EITHER(DIGIPOT_MCP4018, DIGIPOT_MCP4451) - #define HAS_I2C_DIGIPOT 1 + #define HAS_MOTOR_CURRENT_I2C 1 #endif // Multiple Z steppers diff --git a/Marlin/src/inc/Conditionals_post.h b/Marlin/src/inc/Conditionals_post.h index f832137f5b..798bf009c6 100644 --- a/Marlin/src/inc/Conditionals_post.h +++ b/Marlin/src/inc/Conditionals_post.h @@ -1976,7 +1976,7 @@ #define HAS_STEPPER_RESET 1 #endif #if PIN_EXISTS(DIGIPOTSS) - #define HAS_DIGIPOTSS 1 + #define HAS_MOTOR_CURRENT_SPI 1 #endif #if ANY_PIN(MOTOR_CURRENT_PWM_X, MOTOR_CURRENT_PWM_Y, MOTOR_CURRENT_PWM_XY, MOTOR_CURRENT_PWM_Z, MOTOR_CURRENT_PWM_E) #define HAS_MOTOR_CURRENT_PWM 1 diff --git a/Marlin/src/inc/SanityCheck.h b/Marlin/src/inc/SanityCheck.h index c4dcfd54ae..6e97a349f6 100644 --- a/Marlin/src/inc/SanityCheck.h +++ b/Marlin/src/inc/SanityCheck.h @@ -2667,7 +2667,7 @@ static_assert(hbm[Z_AXIS] >= 0, "HOMING_BUMP_MM.Z must be greater than or equal /** * Digipot requirement */ -#if HAS_I2C_DIGIPOT +#if HAS_MOTOR_CURRENT_I2C #if BOTH(DIGIPOT_MCP4018, DIGIPOT_MCP4451) #error "Enable only one of DIGIPOT_MCP4018 or DIGIPOT_MCP4451." #elif !MB(MKS_SBASE) \ diff --git a/Marlin/src/lcd/menu/menu_advanced.cpp b/Marlin/src/lcd/menu/menu_advanced.cpp index 68a10245e9..642d9d84d9 100644 --- a/Marlin/src/lcd/menu/menu_advanced.cpp +++ b/Marlin/src/lcd/menu/menu_advanced.cpp @@ -58,16 +58,16 @@ void menu_tmc(); void menu_backlash(); -#if ENABLED(DAC_STEPPER_CURRENT) +#if ENABLED(HAS_MOTOR_CURRENT_DAC) #include "../../feature/dac/stepper_dac.h" void menu_dac() { static xyze_uint8_t driverPercent; - LOOP_XYZE(i) driverPercent[i] = dac_current_get_percent((AxisEnum)i); + LOOP_XYZE(i) driverPercent[i] = stepper_dac.get_current_percent((AxisEnum)i); START_MENU(); BACK_ITEM(MSG_ADVANCED_SETTINGS); - #define EDIT_DAC_PERCENT(A) EDIT_ITEM(uint8, MSG_DAC_PERCENT_##A, &driverPercent[_AXIS(A)], 0, 100, []{ dac_current_set_percents(driverPercent); }) + #define EDIT_DAC_PERCENT(A) EDIT_ITEM(uint8, MSG_DAC_PERCENT_##A, &driverPercent[_AXIS(A)], 0, 100, []{ stepper_dac.set_current_percents(driverPercent); }) EDIT_DAC_PERCENT(X); EDIT_DAC_PERCENT(Y); EDIT_DAC_PERCENT(Z); @@ -568,7 +568,7 @@ void menu_advanced_settings() { SUBMENU(MSG_BACKLASH, menu_backlash); #endif - #if ENABLED(DAC_STEPPER_CURRENT) + #if ENABLED(HAS_MOTOR_CURRENT_DAC) SUBMENU(MSG_DRIVE_STRENGTH, menu_dac); #endif #if HAS_MOTOR_CURRENT_PWM diff --git a/Marlin/src/module/settings.cpp b/Marlin/src/module/settings.cpp index 3ccd8ffd91..33e5c351ab 100644 --- a/Marlin/src/module/settings.cpp +++ b/Marlin/src/module/settings.cpp @@ -36,7 +36,7 @@ */ // Change EEPROM version if the structure changes -#define EEPROM_VERSION "V81" +#define EEPROM_VERSION "V82" #define EEPROM_OFFSET 100 // Check the integrity of data offsets. @@ -365,7 +365,10 @@ typedef struct SettingsDataStruct { // // HAS_MOTOR_CURRENT_PWM // - uint32_t motor_current_setting[3]; // M907 X Z E + #ifndef MOTOR_CURRENT_COUNT + #define MOTOR_CURRENT_COUNT 3 + #endif + uint32_t motor_current_setting[MOTOR_CURRENT_COUNT]; // M907 X Z E // // CNC_COORDINATE_SYSTEMS @@ -1277,10 +1280,10 @@ void MarlinSettings::postprocess() { { _FIELD_TEST(motor_current_setting); - #if HAS_MOTOR_CURRENT_PWM + #if HAS_MOTOR_CURRENT_SPI || HAS_MOTOR_CURRENT_PWM EEPROM_WRITE(stepper.motor_current_setting); #else - const uint32_t no_current[3] = { 0 }; + const uint32_t no_current[MOTOR_CURRENT_COUNT] = { 0 }; EEPROM_WRITE(no_current); #endif } @@ -2110,10 +2113,16 @@ void MarlinSettings::postprocess() { // Motor Current PWM // { - uint32_t motor_current_setting[3]; _FIELD_TEST(motor_current_setting); + uint32_t motor_current_setting[MOTOR_CURRENT_COUNT] + #if HAS_MOTOR_CURRENT_SPI + = DIGIPOT_MOTOR_CURRENT + #endif + ; + DEBUG_ECHOLNPGM("DIGIPOTS Loading"); EEPROM_READ(motor_current_setting); - #if HAS_MOTOR_CURRENT_PWM + DEBUG_ECHOLNPGM("DIGIPOTS Loaded"); + #if HAS_MOTOR_CURRENT_SPI || HAS_MOTOR_CURRENT_PWM if (!validating) COPY(stepper.motor_current_setting, motor_current_setting); #endif @@ -2791,9 +2800,20 @@ void MarlinSettings::reset() { // #if HAS_MOTOR_CURRENT_PWM - constexpr uint32_t tmp_motor_current_setting[3] = PWM_MOTOR_CURRENT; - LOOP_L_N(q, 3) - stepper.digipot_current(q, (stepper.motor_current_setting[q] = tmp_motor_current_setting[q])); + constexpr uint32_t tmp_motor_current_setting[MOTOR_CURRENT_COUNT] = PWM_MOTOR_CURRENT; + LOOP_L_N(q, MOTOR_CURRENT_COUNT) + stepper.set_digipot_current(q, (stepper.motor_current_setting[q] = tmp_motor_current_setting[q])); + #endif + + // + // DIGIPOTS + // + #if HAS_MOTOR_CURRENT_SPI + static constexpr uint32_t tmp_motor_current_setting[] = DIGIPOT_MOTOR_CURRENT; + DEBUG_ECHOLNPGM("Writing Digipot"); + LOOP_L_N(q, COUNT(tmp_motor_current_setting)) + stepper.set_digipot_current(q, tmp_motor_current_setting[q]); + DEBUG_ECHOLNPGM("Digipot Written"); #endif // @@ -3695,14 +3715,23 @@ void MarlinSettings::reset() { #endif #endif - #if HAS_MOTOR_CURRENT_PWM + #if HAS_MOTOR_CURRENT_SPI || HAS_MOTOR_CURRENT_PWM CONFIG_ECHO_HEADING("Stepper motor currents:"); CONFIG_ECHO_START(); - SERIAL_ECHOLNPAIR_P( - PSTR(" M907 X"), stepper.motor_current_setting[0] - , SP_Z_STR, stepper.motor_current_setting[1] - , SP_E_STR, stepper.motor_current_setting[2] - ); + #if HAS_MOTOR_CURRENT_PWM + SERIAL_ECHOLNPAIR_P( + PSTR(" M907 X"), stepper.motor_current_setting[0] + , SP_Z_STR, stepper.motor_current_setting[1] + , SP_E_STR, stepper.motor_current_setting[2] + ); + #elif HAS_MOTOR_CURRENT_SPI + SERIAL_ECHOPGM(" M907"); + LOOP_L_N(q, MOTOR_CURRENT_COUNT) { + SERIAL_CHAR(' '); + SERIAL_CHAR(axis_codes[q]); + SERIAL_ECHO(stepper.motor_current_setting[q]); + } + #endif #endif /** diff --git a/Marlin/src/module/stepper.cpp b/Marlin/src/module/stepper.cpp index 56a75d1b48..8a5de4b608 100644 --- a/Marlin/src/module/stepper.cpp +++ b/Marlin/src/module/stepper.cpp @@ -83,10 +83,6 @@ Stepper stepper; // Singleton #define BABYSTEPPING_EXTRA_DIR_WAIT -#if HAS_MOTOR_CURRENT_PWM - bool Stepper::initialized; // = false -#endif - #ifdef __AVR__ #include "speed_lookuptable.h" #endif @@ -110,7 +106,7 @@ Stepper stepper; // Singleton #include "../feature/dac/dac_dac084s085.h" #endif -#if HAS_DIGIPOTSS +#if HAS_MOTOR_CURRENT_SPI #include #endif @@ -142,8 +138,12 @@ Stepper stepper; // Singleton bool Stepper::separate_multi_axis = false; #endif -#if HAS_MOTOR_CURRENT_PWM - uint32_t Stepper::motor_current_setting[3]; // Initialized by settings.load() +#if HAS_MOTOR_CURRENT_SPI || HAS_MOTOR_CURRENT_PWM + bool Stepper::initialized; // = false + uint32_t Stepper::motor_current_setting[MOTOR_CURRENT_COUNT]; // Initialized by settings.load() + #if HAS_MOTOR_CURRENT_SPI + constexpr uint32_t Stepper::digipot_count[]; + #endif #endif // private: @@ -2590,8 +2590,8 @@ void Stepper::init() { set_directions(); - #if HAS_DIGIPOTSS || HAS_MOTOR_CURRENT_PWM - TERN_(HAS_MOTOR_CURRENT_PWM, initialized = true); + #if HAS_MOTOR_CURRENT_SPI || HAS_MOTOR_CURRENT_PWM + initialized = true; digipot_init(); #endif } @@ -2930,10 +2930,10 @@ void Stepper::report_positions() { * Software-controlled Stepper Motor Current */ -#if HAS_DIGIPOTSS +#if HAS_MOTOR_CURRENT_SPI // From Arduino DigitalPotControl example - void Stepper::digitalPotWrite(const int16_t address, const int16_t value) { + void Stepper::set_digipot_value_spi(const int16_t address, const int16_t value) { WRITE(DIGIPOTSS_PIN, LOW); // Take the SS pin low to select the chip SPI.transfer(address); // Send the address and value via SPI SPI.transfer(value); @@ -2941,7 +2941,7 @@ void Stepper::report_positions() { //delay(10); } -#endif // HAS_DIGIPOTSS +#endif // HAS_MOTOR_CURRENT_SPI #if HAS_MOTOR_CURRENT_PWM @@ -2958,7 +2958,7 @@ void Stepper::report_positions() { #if ANY_PIN(MOTOR_CURRENT_PWM_E, MOTOR_CURRENT_PWM_E0, MOTOR_CURRENT_PWM_E1) case 2: #endif - digipot_current(i, motor_current_setting[i]); + set_digipot_current(i, motor_current_setting[i]); default: break; } } @@ -2968,22 +2968,23 @@ void Stepper::report_positions() { #if !MB(PRINTRBOARD_G2) - #if HAS_DIGIPOTSS || HAS_MOTOR_CURRENT_PWM + #if HAS_MOTOR_CURRENT_SPI || HAS_MOTOR_CURRENT_PWM - void Stepper::digipot_current(const uint8_t driver, const int16_t current) { + void Stepper::set_digipot_current(const uint8_t driver, const int16_t current) { + if (WITHIN(driver, 0, COUNT(motor_current_setting) - 1)) + motor_current_setting[driver] = current; // update motor_current_setting - #if HAS_DIGIPOTSS + if (!initialized) return; + + #if HAS_MOTOR_CURRENT_SPI + + //SERIAL_ECHOLNPAIR("Digipotss current ", current); const uint8_t digipot_ch[] = DIGIPOT_CHANNELS; - digitalPotWrite(digipot_ch[driver], current); + set_digipot_value_spi(digipot_ch[driver], current); #elif HAS_MOTOR_CURRENT_PWM - if (!initialized) return; - - if (WITHIN(driver, 0, COUNT(motor_current_setting) - 1)) - motor_current_setting[driver] = current; // update motor_current_setting - #define _WRITE_CURRENT_PWM(P) analogWrite(pin_t(MOTOR_CURRENT_PWM_## P ##_PIN), 255L * current / (MOTOR_CURRENT_PWM_RANGE)) switch (driver) { case 0: @@ -3019,17 +3020,13 @@ void Stepper::report_positions() { void Stepper::digipot_init() { - #if HAS_DIGIPOTSS - - static const uint8_t digipot_motor_current[] = DIGIPOT_MOTOR_CURRENT; + #if HAS_MOTOR_CURRENT_SPI SPI.begin(); SET_OUTPUT(DIGIPOTSS_PIN); - LOOP_L_N(i, COUNT(digipot_motor_current)) { - //digitalPotWrite(digipot_ch[i], digipot_motor_current[i]); - digipot_current(i, digipot_motor_current[i]); - } + LOOP_L_N(i, COUNT(motor_current_setting)) + set_digipot_current(i, motor_current_setting[i]); #elif HAS_MOTOR_CURRENT_PWM diff --git a/Marlin/src/module/stepper.h b/Marlin/src/module/stepper.h index da38192d8e..572c3f3f9b 100644 --- a/Marlin/src/module/stepper.h +++ b/Marlin/src/module/stepper.h @@ -245,12 +245,18 @@ class Stepper { static bool separate_multi_axis; #endif - #if HAS_MOTOR_CURRENT_PWM - #ifndef PWM_MOTOR_CURRENT - #define PWM_MOTOR_CURRENT DEFAULT_PWM_MOTOR_CURRENT + #if HAS_MOTOR_CURRENT_SPI || HAS_MOTOR_CURRENT_PWM + #if HAS_MOTOR_CURRENT_PWM + #ifndef PWM_MOTOR_CURRENT + #define PWM_MOTOR_CURRENT DEFAULT_PWM_MOTOR_CURRENT + #endif + #define MOTOR_CURRENT_COUNT 3 + #elif HAS_MOTOR_CURRENT_SPI + static constexpr uint32_t digipot_count[] = DIGIPOT_MOTOR_CURRENT; + #define MOTOR_CURRENT_COUNT COUNT(Stepper::digipot_count) #endif - static uint32_t motor_current_setting[3]; static bool initialized; + static uint32_t motor_current_setting[MOTOR_CURRENT_COUNT]; // Initialized by settings.load() #endif // Last-moved extruder, as set when the last movement was fetched from planner @@ -457,9 +463,9 @@ class Stepper { // Triggered position of an axis in steps static int32_t triggered_position(const AxisEnum axis); - #if HAS_DIGIPOTSS || HAS_MOTOR_CURRENT_PWM - static void digitalPotWrite(const int16_t address, const int16_t value); - static void digipot_current(const uint8_t driver, const int16_t current); + #if HAS_MOTOR_CURRENT_SPI || HAS_MOTOR_CURRENT_PWM + static void set_digipot_value_spi(const int16_t address, const int16_t value); + static void set_digipot_current(const uint8_t driver, const int16_t current); #endif #if HAS_MICROSTEPS @@ -582,7 +588,7 @@ class Stepper { static int32_t _eval_bezier_curve(const uint32_t curr_step); #endif - #if HAS_DIGIPOTSS || HAS_MOTOR_CURRENT_PWM + #if HAS_MOTOR_CURRENT_SPI || HAS_MOTOR_CURRENT_PWM static void digipot_init(); #endif diff --git a/Marlin/src/pins/ramps/pins_RIGIDBOARD_V2.h b/Marlin/src/pins/ramps/pins_RIGIDBOARD_V2.h index 406cbec816..1428de31a2 100644 --- a/Marlin/src/pins/ramps/pins_RIGIDBOARD_V2.h +++ b/Marlin/src/pins/ramps/pins_RIGIDBOARD_V2.h @@ -34,7 +34,7 @@ // // I2C based DAC like on the Printrboard REVF -#define DAC_STEPPER_CURRENT +#define HAS_MOTOR_CURRENT_DAC // Channels available for DAC, For Rigidboard there are 4 #define DAC_STEPPER_ORDER { 0, 1, 2, 3 } diff --git a/Marlin/src/pins/teensy2/pins_PRINTRBOARD_REVF.h b/Marlin/src/pins/teensy2/pins_PRINTRBOARD_REVF.h index 6ffd35dff2..4809cc8d86 100644 --- a/Marlin/src/pins/teensy2/pins_PRINTRBOARD_REVF.h +++ b/Marlin/src/pins/teensy2/pins_PRINTRBOARD_REVF.h @@ -143,7 +143,7 @@ #endif // NO_EXTRUDRBOARD // Enable control of stepper motor currents with the I2C based MCP4728 DAC used on Printrboard REVF -#define DAC_STEPPER_CURRENT +#define HAS_MOTOR_CURRENT_DAC // Set default drive strength percents if not already defined - X, Y, Z, E axis #ifndef DAC_MOTOR_CURRENT_DEFAULT diff --git a/platformio.ini b/platformio.ini index d4beca6519..9d3fafd69e 100644 --- a/platformio.ini +++ b/platformio.ini @@ -211,7 +211,7 @@ HAS_TRINAMIC_CONFIG = TMCStepper@~0.7.1 src_filter=+ + + + + HAS_STEALTHCHOP = src_filter=+ SR_LCD_3W_NL = SailfishLCD=https://github.com/mikeshub/SailfishLCD/archive/master.zip -HAS_I2C_DIGIPOT = SlowSoftI2CMaster +HAS_MOTOR_CURRENT_I2C = SlowSoftI2CMaster src_filter=+ HAS_TMC26X = TMC26XStepper=https://github.com/trinamic/TMC26XStepper/archive/master.zip src_filter=+ @@ -277,7 +277,7 @@ CANCEL_OBJECTS = src_filter=+ + + EXTERNAL_CLOSED_LOOP_CONTROLLER = src_filter=+ + USE_CONTROLLER_FAN = src_filter=+ -DAC_STEPPER_CURRENT = src_filter=+ +HAS_MOTOR_CURRENT_DAC = src_filter=+ DIRECT_STEPPING = src_filter=+ + EMERGENCY_PARSER = src_filter=+ - I2C_POSITION_ENCODERS = src_filter=+