zaubentrucker/muele-marlin
1
0
Fork 0
Code Issues Pull requests Actions Packages Projects Releases Wiki Activity

Merge pull request #4805 from thinkyhead/rc_config_adjustment

Browse source 
Additional documentation of Configuration.h
This commit is contained in:
Scott Lahteine 2016-09-16 15:13:20 -05:00 committed by GitHub
parent b08bd84f8e a1812b55f6
commit 502150046c
25 changed files with 1133 additions and 300 deletions
Show stats Download patch file Download diff file Expand all files Collapse all files

106
Marlin/Configuration.h
View file

@ -105,15 +105,24 @@
//#define SHOW_CUSTOM_BOOTSCREEN //#define SHOW_CUSTOM_BOOTSCREEN
// @section machine // @section machine
// SERIAL_PORT selects which serial port should be used for communication with the host. /**
// This allows the connection of wireless adapters (for instance) to non-default port pins. * Select which serial port on the board will be used for communication with the host.
// Serial port 0 is still used by the Arduino bootloader regardless of this setting. * This allows the connection of wireless adapters (for instance) to non-default port pins.
// :[0,1,2,3,4,5,6,7] * Serial port 0 is always used by the Arduino bootloader regardless of this setting.
*
* :[0,1,2,3,4,5,6,7]
*/
#define SERIAL_PORT 0 #define SERIAL_PORT 0
// This determines the communication speed of the printer
// :[2400,9600,19200,38400,57600,115200,250000]
#define BAUDRATE 250000 #define BAUDRATE 250000
/**
* This setting determines the communication speed of the printer.
*
* 250000 works in most cases, but you might try a lower speed if
* you commonly experience drop-outs during host printing.
*
* :[2400,9600,19200,38400,57600,115200,250000]
*/
// Enable the Bluetooth serial interface on AT90USB devices // Enable the Bluetooth serial interface on AT90USB devices
//#define BLUETOOTH //#define BLUETOOTH
@ -169,14 +178,22 @@
//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis //#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis //#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
//// The following define selects which power supply you have. Please choose the one that matches your setup /**
// 1 = ATX * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN
// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC) *
// :{1:'ATX',2:'X-Box 360'} * 0 = No Power Switch
#define POWER_SUPPLY 1 * 1 = ATX
* 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
*
* :{0:'No power switch',1:'ATX',2:'X-Box 360'}
*/
#define POWER_SUPPLY 0
// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it. #if POWER_SUPPLY > 0
//#define PS_DEFAULT_OFF // Enable this option to leave the PSU off at startup.
// Power to steppers and heaters will need to be turned on with M80.
//#define PS_DEFAULT_OFF
#endif
// @section temperature // @section temperature
@ -355,8 +372,9 @@
#define EXTRUDE_MINTEMP 170 #define EXTRUDE_MINTEMP 170
// This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH.
// Note that for Bowden Extruders a too-small value here may prevent loading.
#define PREVENT_LENGTHY_EXTRUDE #define PREVENT_LENGTHY_EXTRUDE
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) #define EXTRUDE_MAXLENGTH 200
//=========================================================================== //===========================================================================
//======================== Thermal Runaway Protection ======================= //======================== Thermal Runaway Protection =======================
@ -436,20 +454,56 @@
//============================================================================= //=============================================================================
// @section motion // @section motion
#define DEFAULT_AXIS_STEPS_PER_UNIT {80,80,4000,500} // default steps per unit for Ultimaker /**
#define DEFAULT_MAX_FEEDRATE {300, 300, 5, 25} // (mm/sec) * Default Settings
#define DEFAULT_MAX_ACCELERATION {3000,3000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. *
* These settings can be reset by M502
*
* Note that if EEPROM is enabled, saved values will override these.
*/
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves /**
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts * Default Axis Steps Per Unit (steps/mm)
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves * Override with M92
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 4000, 500 }
// "Jerk" specifies the minimum speed change that requires acceleration. /**
// When changing speed and direction, if the difference is less than the * Default Max Feed Rate (mm/s)
// value set here, it may happen instantaneously. * Override with M203
#define DEFAULT_XYJERK 20.0 // (mm/sec) */
#define DEFAULT_ZJERK 0.4 // (mm/sec) #define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 }
#define DEFAULT_EJERK 5.0 // (mm/sec)
/**
* Default Max Acceleration (change/s) change = mm/s
* Override with M201
*
* Maximum start speed for accelerated moves: { X, Y, Z, E }
*/
#define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 }
/**
* Default Acceleration (change/s) change = mm/s
* Override with M204
*
* M204 P Acceleration
* M204 R Retract Acceleration
* M204 T Travel Acceleration
*/
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves
/**
* Defult Jerk (mm/s)
*
* "Jerk" specifies the minimum speed change that requires acceleration.
* When changing speed and direction, if the difference is less than the
* value set here, it may happen instantaneously.
*/
#define DEFAULT_XYJERK 20.0
#define DEFAULT_ZJERK 0.4
#define DEFAULT_EJERK 5.0
//=========================================================================== //===========================================================================

63
Marlin/example_configurations/Cartesio/Configuration.h
View file

@ -355,8 +355,9 @@
#define EXTRUDE_MINTEMP 170 #define EXTRUDE_MINTEMP 170
// This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH.
// Note that for Bowden Extruders a too-small value here may prevent loading.
#define PREVENT_LENGTHY_EXTRUDE #define PREVENT_LENGTHY_EXTRUDE
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) #define EXTRUDE_MAXLENGTH 200
//=========================================================================== //===========================================================================
//======================== Thermal Runaway Protection ======================= //======================== Thermal Runaway Protection =======================
@ -436,20 +437,56 @@
//============================================================================= //=============================================================================
// @section motion // @section motion
#define DEFAULT_AXIS_STEPS_PER_UNIT {71.128,71.128,640,152} /**
#define DEFAULT_MAX_FEEDRATE {200,200,20,20} // (mm/sec) * Default Settings
#define DEFAULT_MAX_ACCELERATION {1000,1000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. *
* These settings can be reset by M502
*
* Note that if EEPROM is enabled, saved values will override these.
*/
#define DEFAULT_ACCELERATION 500 // X, Y, Z and E acceleration in mm/s^2 for printing moves /**
#define DEFAULT_RETRACT_ACCELERATION 10000 // E acceleration in mm/s^2 for retracts * Default Axis Steps Per Unit (steps/mm)
#define DEFAULT_TRAVEL_ACCELERATION 1000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves * Override with M92
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 71.128, 71.128, 640, 152 }
// "Jerk" specifies the minimum speed change that requires acceleration. /**
// When changing speed and direction, if the difference is less than the * Default Max Feed Rate (mm/s)
// value set here, it may happen instantaneously. * Override with M203
#define DEFAULT_XYJERK 10.0 // (mm/sec) */
#define DEFAULT_ZJERK 0.4 // (mm/sec) #define DEFAULT_MAX_FEEDRATE { 200, 200, 20, 20 } // (mm/sec)
#define DEFAULT_EJERK 5.0 // (mm/sec)
/**
* Default Max Acceleration (change/s) change = mm/s
* Override with M201
*
* Maximum start speed for accelerated moves: { X, Y, Z, E }
*/
#define DEFAULT_MAX_ACCELERATION { 1000, 1000, 100, 10000 }
/**
* Default Acceleration (change/s) change = mm/s
* Override with M204
*
* M204 P Acceleration
* M204 R Retract Acceleration
* M204 T Travel Acceleration
*/
#define DEFAULT_ACCELERATION 500 // X, Y, Z and E acceleration for printing moves
#define DEFAULT_RETRACT_ACCELERATION 10000 // E acceleration for retracts
#define DEFAULT_TRAVEL_ACCELERATION 1000 // X, Y, Z acceleration for travel (non printing) moves
/**
* Defult Jerk (mm/s)
*
* "Jerk" specifies the minimum speed change that requires acceleration.
* When changing speed and direction, if the difference is less than the
* value set here, it may happen instantaneously.
*/
#define DEFAULT_XYJERK 10.0
#define DEFAULT_ZJERK 0.4
#define DEFAULT_EJERK 5.0
//=========================================================================== //===========================================================================

63
Marlin/example_configurations/Felix/Configuration.h
View file

@ -337,8 +337,9 @@
#define EXTRUDE_MINTEMP 170 #define EXTRUDE_MINTEMP 170
// This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH.
// Note that for Bowden Extruders a too-small value here may prevent loading.
#define PREVENT_LENGTHY_EXTRUDE #define PREVENT_LENGTHY_EXTRUDE
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) #define EXTRUDE_MAXLENGTH 200
//=========================================================================== //===========================================================================
//======================== Thermal Runaway Protection ======================= //======================== Thermal Runaway Protection =======================
@ -419,20 +420,56 @@
// @section motion // @section motion
// default steps per unit for Felix 2.0/3.0: 0.00249mm x/y rounding error with 3mm pitch HTD belt and 14 tooth pulleys. 0 z error. // default steps per unit for Felix 2.0/3.0: 0.00249mm x/y rounding error with 3mm pitch HTD belt and 14 tooth pulleys. 0 z error.
#define DEFAULT_AXIS_STEPS_PER_UNIT {76.190476, 76.190476, 1600, 164} /**
#define DEFAULT_MAX_FEEDRATE {500, 500, 5, 25} // (mm/sec) * Default Settings
#define DEFAULT_MAX_ACCELERATION {5000,5000,100,80000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. *
* These settings can be reset by M502
*
* Note that if EEPROM is enabled, saved values will override these.
*/
#define DEFAULT_ACCELERATION 1750 // X, Y, Z and E max acceleration in mm/s^2 for printing moves /**
#define DEFAULT_RETRACT_ACCELERATION 5000 // E acceleration in mm/s^2 for retracts * Default Axis Steps Per Unit (steps/mm)
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves * Override with M92
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 76.190476, 76.190476, 1600, 164 }
// "Jerk" specifies the minimum speed change that requires acceleration. /**
// When changing speed and direction, if the difference is less than the * Default Max Feed Rate (mm/s)
// value set here, it may happen instantaneously. * Override with M203
#define DEFAULT_XYJERK 10.0 // (mm/sec) */
#define DEFAULT_ZJERK 0.3 // (mm/sec) #define DEFAULT_MAX_FEEDRATE { 500, 500, 5, 25 }
#define DEFAULT_EJERK 5.0 // (mm/sec)
/**
* Default Max Acceleration (change/s) change = mm/s
* Override with M201
*
* Maximum start speed for accelerated moves: { X, Y, Z, E }
*/
#define DEFAULT_MAX_ACCELERATION { 5000, 5000, 100, 80000 }
/**
* Default Acceleration (change/s) change = mm/s
* Override with M204
*
* M204 P Acceleration
* M204 R Retract Acceleration
* M204 T Travel Acceleration
*/
#define DEFAULT_ACCELERATION 1750 // X, Y, Z and E max acceleration for printing moves
#define DEFAULT_RETRACT_ACCELERATION 5000 // E acceleration for retracts
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves
/**
* Defult Jerk (mm/s)
*
* "Jerk" specifies the minimum speed change that requires acceleration.
* When changing speed and direction, if the difference is less than the
* value set here, it may happen instantaneously.
*/
#define DEFAULT_XYJERK 10.0
#define DEFAULT_ZJERK 0.3
#define DEFAULT_EJERK 5.0
//=========================================================================== //===========================================================================

63
Marlin/example_configurations/Felix/DUAL/Configuration.h
View file

@ -335,8 +335,9 @@
#define EXTRUDE_MINTEMP 170 #define EXTRUDE_MINTEMP 170
// This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH.
// Note that for Bowden Extruders a too-small value here may prevent loading.
#define PREVENT_LENGTHY_EXTRUDE #define PREVENT_LENGTHY_EXTRUDE
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) #define EXTRUDE_MAXLENGTH 200
//=========================================================================== //===========================================================================
//======================== Thermal Runaway Protection ======================= //======================== Thermal Runaway Protection =======================
@ -417,20 +418,56 @@
// @section motion // @section motion
// default steps per unit for Felix 2.0/3.0: 0.00249mm x/y rounding error with 3mm pitch HTD belt and 14 tooth pulleys. 0 z error. // default steps per unit for Felix 2.0/3.0: 0.00249mm x/y rounding error with 3mm pitch HTD belt and 14 tooth pulleys. 0 z error.
#define DEFAULT_AXIS_STEPS_PER_UNIT {76.190476, 76.190476, 1600, 164} /**
#define DEFAULT_MAX_FEEDRATE {500, 500, 5, 25} // (mm/sec) * Default Settings
#define DEFAULT_MAX_ACCELERATION {5000,5000,100,80000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. *
* These settings can be reset by M502
*
* Note that if EEPROM is enabled, saved values will override these.
*/
#define DEFAULT_ACCELERATION 1750 // X, Y, Z and E max acceleration in mm/s^2 for printing moves /**
#define DEFAULT_RETRACT_ACCELERATION 5000 // E acceleration in mm/s^2 for retracts * Default Axis Steps Per Unit (steps/mm)
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves * Override with M92
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 76.190476, 76.190476, 1600, 164 }
// "Jerk" specifies the minimum speed change that requires acceleration. /**
// When changing speed and direction, if the difference is less than the * Default Max Feed Rate (mm/s)
// value set here, it may happen instantaneously. * Override with M203
#define DEFAULT_XYJERK 10.0 // (mm/sec) */
#define DEFAULT_ZJERK 0.3 // (mm/sec) #define DEFAULT_MAX_FEEDRATE { 500, 500, 5, 25 }
#define DEFAULT_EJERK 5.0 // (mm/sec)
/**
* Default Max Acceleration (change/s) change = mm/s
* Override with M201
*
* Maximum start speed for accelerated moves: { X, Y, Z, E }
*/
#define DEFAULT_MAX_ACCELERATION { 5000, 5000, 100, 80000 }
/**
* Default Acceleration (change/s) change = mm/s
* Override with M204
*
* M204 P Acceleration
* M204 R Retract Acceleration
* M204 T Travel Acceleration
*/
#define DEFAULT_ACCELERATION 1750 // X, Y, Z and E max acceleration for printing moves
#define DEFAULT_RETRACT_ACCELERATION 5000 // E acceleration for retracts
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves
/**
* Defult Jerk (mm/s)
*
* "Jerk" specifies the minimum speed change that requires acceleration.
* When changing speed and direction, if the difference is less than the
* value set here, it may happen instantaneously.
*/
#define DEFAULT_XYJERK 10.0
#define DEFAULT_ZJERK 0.3
#define DEFAULT_EJERK 5.0
//=========================================================================== //===========================================================================

63
Marlin/example_configurations/Hephestos/Configuration.h
View file

@ -347,8 +347,9 @@
#define EXTRUDE_MINTEMP 170 #define EXTRUDE_MINTEMP 170
// This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH.
// Note that for Bowden Extruders a too-small value here may prevent loading.
#define PREVENT_LENGTHY_EXTRUDE #define PREVENT_LENGTHY_EXTRUDE
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) #define EXTRUDE_MAXLENGTH 200
//=========================================================================== //===========================================================================
//======================== Thermal Runaway Protection ======================= //======================== Thermal Runaway Protection =======================
@ -428,20 +429,56 @@
//============================================================================= //=============================================================================
// @section motion // @section motion
#define DEFAULT_AXIS_STEPS_PER_UNIT {80,80,4000,100.47095761381482} // default steps per unit for Ultimaker /**
#define DEFAULT_MAX_FEEDRATE {200, 200, 3.3, 25} // (mm/sec) * Default Settings
#define DEFAULT_MAX_ACCELERATION {1100,1100,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. *
* These settings can be reset by M502
*
* Note that if EEPROM is enabled, saved values will override these.
*/
#define DEFAULT_ACCELERATION 650 // X, Y, Z and E acceleration in mm/s^2 for printing moves /**
#define DEFAULT_RETRACT_ACCELERATION 1000 // E acceleration in mm/s^2 for retracts * Default Axis Steps Per Unit (steps/mm)
#define DEFAULT_TRAVEL_ACCELERATION 1000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves * Override with M92
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 4000, 100.47095761381482 }
// "Jerk" specifies the minimum speed change that requires acceleration. /**
// When changing speed and direction, if the difference is less than the * Default Max Feed Rate (mm/s)
// value set here, it may happen instantaneously. * Override with M203
#define DEFAULT_XYJERK 10.0 // (mm/sec) */
#define DEFAULT_ZJERK 0.4 // (mm/sec) #define DEFAULT_MAX_FEEDRATE { 200, 200, 3.3, 25 }
#define DEFAULT_EJERK 5.0 // (mm/sec)
/**
* Default Max Acceleration (change/s) change = mm/s
* Override with M201
*
* Maximum start speed for accelerated moves: { X, Y, Z, E }
*/
#define DEFAULT_MAX_ACCELERATION { 1100, 1100, 100, 10000 }
/**
* Default Acceleration (change/s) change = mm/s
* Override with M204
*
* M204 P Acceleration
* M204 R Retract Acceleration
* M204 T Travel Acceleration
*/
#define DEFAULT_ACCELERATION 650 // X, Y, Z and E acceleration for printing moves
#define DEFAULT_RETRACT_ACCELERATION 1000 // E acceleration for retracts
#define DEFAULT_TRAVEL_ACCELERATION 1000 // X, Y, Z acceleration for travel (non printing) moves
/**
* Defult Jerk (mm/s)
*
* "Jerk" specifies the minimum speed change that requires acceleration.
* When changing speed and direction, if the difference is less than the
* value set here, it may happen instantaneously.
*/
#define DEFAULT_XYJERK 10.0
#define DEFAULT_ZJERK 0.4
#define DEFAULT_EJERK 5.0
//=========================================================================== //===========================================================================

63
Marlin/example_configurations/Hephestos_2/Configuration.h
View file

@ -349,8 +349,9 @@
#define EXTRUDE_MINTEMP 170 #define EXTRUDE_MINTEMP 170
// This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH.
// Note that for Bowden Extruders a too-small value here may prevent loading.
#define PREVENT_LENGTHY_EXTRUDE #define PREVENT_LENGTHY_EXTRUDE
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) #define EXTRUDE_MAXLENGTH 200
//=========================================================================== //===========================================================================
//======================== Thermal Runaway Protection ======================= //======================== Thermal Runaway Protection =======================
@ -430,20 +431,56 @@
//============================================================================= //=============================================================================
// @section motion // @section motion
#define DEFAULT_AXIS_STEPS_PER_UNIT {160, 160, 8000, 210.02} // Steps per unit /**
#define DEFAULT_MAX_FEEDRATE {250, 250, 2, 200} // mm/sec * Default Settings
#define DEFAULT_MAX_ACCELERATION {1000, 1000, 20, 1000} // X, Y, Z, E max start speed for accelerated moves *
* These settings can be reset by M502
*
* Note that if EEPROM is enabled, saved values will override these.
*/
#define DEFAULT_ACCELERATION 1000 // X, Y, Z and E acceleration in mm/s^2 for printing moves /**
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts * Default Axis Steps Per Unit (steps/mm)
#define DEFAULT_TRAVEL_ACCELERATION 1000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves * Override with M92
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 160, 160, 8000, 210.02 }
// "Jerk" specifies the minimum speed change that requires acceleration. /**
// When changing speed and direction, if the difference is less than the * Default Max Feed Rate (mm/s)
// value set here, it may happen instantaneously. * Override with M203
#define DEFAULT_XYJERK 20.0 // (mm/sec) */
#define DEFAULT_ZJERK 0.4 // (mm/sec) #define DEFAULT_MAX_FEEDRATE { 250, 250, 2, 200 }
#define DEFAULT_EJERK 2.0 // (mm/sec)
/**
* Default Max Acceleration (change/s) change = mm/s
* Override with M201
*
* Maximum start speed for accelerated moves: { X, Y, Z, E }
*/
#define DEFAULT_MAX_ACCELERATION { 1000, 1000, 20, 1000 }
/**
* Default Acceleration (change/s) change = mm/s
* Override with M204
*
* M204 P Acceleration
* M204 R Retract Acceleration
* M204 T Travel Acceleration
*/
#define DEFAULT_ACCELERATION 1000 // X, Y, Z and E acceleration for printing moves
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts
#define DEFAULT_TRAVEL_ACCELERATION 1000 // X, Y, Z acceleration for travel (non printing) moves
/**
* Defult Jerk (mm/s)
*
* "Jerk" specifies the minimum speed change that requires acceleration.
* When changing speed and direction, if the difference is less than the
* value set here, it may happen instantaneously.
*/
#define DEFAULT_XYJERK 20.0
#define DEFAULT_ZJERK 0.4
#define DEFAULT_EJERK 2.0
//=========================================================================== //===========================================================================

63
Marlin/example_configurations/K8200/Configuration.h
View file

@ -372,8 +372,9 @@
#define EXTRUDE_MINTEMP 170 #define EXTRUDE_MINTEMP 170
// This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH.
// Note that for Bowden Extruders a too-small value here may prevent loading.
#define PREVENT_LENGTHY_EXTRUDE #define PREVENT_LENGTHY_EXTRUDE
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) #define EXTRUDE_MAXLENGTH 200
//=========================================================================== //===========================================================================
//======================== Thermal Runaway Protection ======================= //======================== Thermal Runaway Protection =======================
@ -453,20 +454,56 @@
//============================================================================= //=============================================================================
// @section motion // @section motion
#define DEFAULT_AXIS_STEPS_PER_UNIT {64.25,64.25,2560,600} // default steps per unit for K8200 /**
#define DEFAULT_MAX_FEEDRATE {500, 500, 5, 500} // (mm/sec) * Default Settings
#define DEFAULT_MAX_ACCELERATION {9000,9000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. *
* These settings can be reset by M502
*
* Note that if EEPROM is enabled, saved values will override these.
*/
#define DEFAULT_ACCELERATION 1000 // X, Y, Z and E acceleration in mm/s^2 for printing moves /**
#define DEFAULT_RETRACT_ACCELERATION 1000 // E acceleration in mm/s^2 for retracts * Default Axis Steps Per Unit (steps/mm)
#define DEFAULT_TRAVEL_ACCELERATION 1000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves * Override with M92
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 64.25, 64.25, 2560, 600 } // default steps per unit for K8200
// "Jerk" specifies the minimum speed change that requires acceleration. /**
// When changing speed and direction, if the difference is less than the * Default Max Feed Rate (mm/s)
// value set here, it may happen instantaneously. * Override with M203
#define DEFAULT_XYJERK 20.0 // (mm/sec) */
#define DEFAULT_ZJERK 0.4 // (mm/sec) #define DEFAULT_MAX_FEEDRATE { 500, 500, 5, 500 }
#define DEFAULT_EJERK 5.0 // (mm/sec)
/**
* Default Max Acceleration (change/s) change = mm/s
* Override with M201
*
* Maximum start speed for accelerated moves: { X, Y, Z, E }
*/
#define DEFAULT_MAX_ACCELERATION { 9000, 9000, 100, 10000 }
/**
* Default Acceleration (change/s) change = mm/s
* Override with M204
*
* M204 P Acceleration
* M204 R Retract Acceleration
* M204 T Travel Acceleration
*/
#define DEFAULT_ACCELERATION 1000 // X, Y, Z and E acceleration for printing moves
#define DEFAULT_RETRACT_ACCELERATION 1000 // E acceleration for retracts
#define DEFAULT_TRAVEL_ACCELERATION 1000 // X, Y, Z acceleration for travel (non printing) moves
/**
* Defult Jerk (mm/s)
*
* "Jerk" specifies the minimum speed change that requires acceleration.
* When changing speed and direction, if the difference is less than the
* value set here, it may happen instantaneously.
*/
#define DEFAULT_XYJERK 20.0
#define DEFAULT_ZJERK 0.4
#define DEFAULT_EJERK 5.0
//=========================================================================== //===========================================================================

63
Marlin/example_configurations/K8400/Configuration.h
View file

@ -355,8 +355,9 @@
#define EXTRUDE_MINTEMP 170 #define EXTRUDE_MINTEMP 170
// This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH.
// Note that for Bowden Extruders a too-small value here may prevent loading.
#define PREVENT_LENGTHY_EXTRUDE #define PREVENT_LENGTHY_EXTRUDE
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) #define EXTRUDE_MAXLENGTH 200
//=========================================================================== //===========================================================================
//======================== Thermal Runaway Protection ======================= //======================== Thermal Runaway Protection =======================
@ -436,20 +437,56 @@
//============================================================================= //=============================================================================
// @section motion // @section motion
#define DEFAULT_AXIS_STEPS_PER_UNIT {134.74,134.74,4266.66,148.7} // default steps per unit for Ultimaker /**
#define DEFAULT_MAX_FEEDRATE {160, 160, 10, 10000} // (mm/sec) * Default Settings
#define DEFAULT_MAX_ACCELERATION {9000,9000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. *
* These settings can be reset by M502
*
* Note that if EEPROM is enabled, saved values will override these.
*/
#define DEFAULT_ACCELERATION 6000 // X, Y, Z and E acceleration in mm/s^2 for printing moves /**
#define DEFAULT_RETRACT_ACCELERATION 6000 // E acceleration in mm/s^2 for retracts * Default Axis Steps Per Unit (steps/mm)
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves * Override with M92
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 134.74, 134.74, 4266.66, 148.7 }
// "Jerk" specifies the minimum speed change that requires acceleration. /**
// When changing speed and direction, if the difference is less than the * Default Max Feed Rate (mm/s)
// value set here, it may happen instantaneously. * Override with M203
#define DEFAULT_XYJERK 10.0 // (mm/sec) */
#define DEFAULT_ZJERK 0.5 // (mm/sec) #define DEFAULT_MAX_FEEDRATE { 160, 160, 10, 10000 }
#define DEFAULT_EJERK 20.0 // (mm/sec)
/**
* Default Max Acceleration (change/s) change = mm/s
* Override with M201
*
* Maximum start speed for accelerated moves: { X, Y, Z, E }
*/
#define DEFAULT_MAX_ACCELERATION { 9000, 9000, 100, 10000 }
/**
* Default Acceleration (change/s) change = mm/s
* Override with M204
*
* M204 P Acceleration
* M204 R Retract Acceleration
* M204 T Travel Acceleration
*/
#define DEFAULT_ACCELERATION 6000 // X, Y, Z and E acceleration for printing moves
#define DEFAULT_RETRACT_ACCELERATION 6000 // E acceleration for retracts
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves
/**
* Defult Jerk (mm/s)
*
* "Jerk" specifies the minimum speed change that requires acceleration.
* When changing speed and direction, if the difference is less than the
* value set here, it may happen instantaneously.
*/
#define DEFAULT_XYJERK 10.0
#define DEFAULT_ZJERK 0.5
#define DEFAULT_EJERK 20.0
//=========================================================================== //===========================================================================

63
Marlin/example_configurations/K8400/Dual-head/Configuration.h
View file

@ -355,8 +355,9 @@
#define EXTRUDE_MINTEMP 170 #define EXTRUDE_MINTEMP 170
// This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH.
// Note that for Bowden Extruders a too-small value here may prevent loading.
#define PREVENT_LENGTHY_EXTRUDE #define PREVENT_LENGTHY_EXTRUDE
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) #define EXTRUDE_MAXLENGTH 200
//=========================================================================== //===========================================================================
//======================== Thermal Runaway Protection ======================= //======================== Thermal Runaway Protection =======================
@ -436,20 +437,56 @@
//============================================================================= //=============================================================================
// @section motion // @section motion
#define DEFAULT_AXIS_STEPS_PER_UNIT {134.74,134.74,4266.66,148.7} // default steps per unit for Ultimaker /**
#define DEFAULT_MAX_FEEDRATE {160, 160, 10, 10000} // (mm/sec) * Default Settings
#define DEFAULT_MAX_ACCELERATION {9000,9000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. *
* These settings can be reset by M502
*
* Note that if EEPROM is enabled, saved values will override these.
*/
#define DEFAULT_ACCELERATION 6000 // X, Y, Z and E acceleration in mm/s^2 for printing moves /**
#define DEFAULT_RETRACT_ACCELERATION 6000 // E acceleration in mm/s^2 for retracts * Default Axis Steps Per Unit (steps/mm)
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves * Override with M92
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 134.74, 134.74, 4266.66, 148.7 }
// "Jerk" specifies the minimum speed change that requires acceleration. /**
// When changing speed and direction, if the difference is less than the * Default Max Feed Rate (mm/s)
// value set here, it may happen instantaneously. * Override with M203
#define DEFAULT_XYJERK 10.0 // (mm/sec) */
#define DEFAULT_ZJERK 0.5 // (mm/sec) #define DEFAULT_MAX_FEEDRATE { 160, 160, 10, 10000 }
#define DEFAULT_EJERK 20.0 // (mm/sec)
/**
* Default Max Acceleration (change/s) change = mm/s
* Override with M201
*
* Maximum start speed for accelerated moves: { X, Y, Z, E }
*/
#define DEFAULT_MAX_ACCELERATION { 9000, 9000, 100, 10000 }
/**
* Default Acceleration (change/s) change = mm/s
* Override with M204
*
* M204 P Acceleration
* M204 R Retract Acceleration
* M204 T Travel Acceleration
*/
#define DEFAULT_ACCELERATION 6000 // X, Y, Z and E acceleration for printing moves
#define DEFAULT_RETRACT_ACCELERATION 6000 // E acceleration for retracts
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves
/**
* Defult Jerk (mm/s)
*
* "Jerk" specifies the minimum speed change that requires acceleration.
* When changing speed and direction, if the difference is less than the
* value set here, it may happen instantaneously.
*/
#define DEFAULT_XYJERK 10.0
#define DEFAULT_ZJERK 0.5
#define DEFAULT_EJERK 20.0
//=========================================================================== //===========================================================================

63
Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
View file

@ -355,8 +355,9 @@
#define EXTRUDE_MINTEMP 170 #define EXTRUDE_MINTEMP 170
// This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH.
// Note that for Bowden Extruders a too-small value here may prevent loading.
#define PREVENT_LENGTHY_EXTRUDE #define PREVENT_LENGTHY_EXTRUDE
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) #define EXTRUDE_MAXLENGTH 200
//=========================================================================== //===========================================================================
//======================== Thermal Runaway Protection ======================= //======================== Thermal Runaway Protection =======================
@ -436,20 +437,56 @@
//============================================================================= //=============================================================================
// @section motion // @section motion
#define DEFAULT_AXIS_STEPS_PER_UNIT {78.7402*2,78.7402*2,5120.00,760*1*1.5} // default steps per unit for Ultimaker /**
#define DEFAULT_MAX_FEEDRATE {300, 300, 5, 25} // (mm/sec) * Default Settings
#define DEFAULT_MAX_ACCELERATION {3000,3000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. *
* These settings can be reset by M502
*
* Note that if EEPROM is enabled, saved values will override these.
*/
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves /**
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts * Default Axis Steps Per Unit (steps/mm)
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves * Override with M92
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT {78.7402*2,78.7402*2,5120.00,760*1*1.5}
// "Jerk" specifies the minimum speed change that requires acceleration. /**
// When changing speed and direction, if the difference is less than the * Default Max Feed Rate (mm/s)
// value set here, it may happen instantaneously. * Override with M203
#define DEFAULT_XYJERK 20.0 // (mm/sec) */
#define DEFAULT_ZJERK 0.4 // (mm/sec) #define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 }
#define DEFAULT_EJERK 5.0 // (mm/sec)
/**
* Default Max Acceleration (change/s) change = mm/s
* Override with M201
*
* Maximum start speed for accelerated moves: { X, Y, Z, E }
*/
#define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 }
/**
* Default Acceleration (change/s) change = mm/s
* Override with M204
*
* M204 P Acceleration
* M204 R Retract Acceleration
* M204 T Travel Acceleration
*/
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves
/**
* Defult Jerk (mm/s)
*
* "Jerk" specifies the minimum speed change that requires acceleration.
* When changing speed and direction, if the difference is less than the
* value set here, it may happen instantaneously.
*/
#define DEFAULT_XYJERK 20.0
#define DEFAULT_ZJERK 0.4
#define DEFAULT_EJERK 5.0
//=========================================================================== //===========================================================================

65
Marlin/example_configurations/RigidBot/Configuration.h
View file

@ -352,8 +352,9 @@
#define EXTRUDE_MINTEMP 170 #define EXTRUDE_MINTEMP 170
// This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH.
// Note that for Bowden Extruders a too-small value here may prevent loading.
#define PREVENT_LENGTHY_EXTRUDE #define PREVENT_LENGTHY_EXTRUDE
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) #define EXTRUDE_MAXLENGTH 200
//=========================================================================== //===========================================================================
//======================== Thermal Runaway Protection ======================= //======================== Thermal Runaway Protection =======================
@ -433,21 +434,57 @@
//============================================================================= //=============================================================================
// @section motion // @section motion
#define DEFAULT_AXIS_STEPS_PER_UNIT {44.3090, 22.1545, 1600, 53.5} // default steps per unit for RigidBot with standard hardware /**
// default steps for 16-tooth pulleys {100.06,50.06,1600,76}, HPX2-MAX E=504, RigidBot E=53.5, Peter Stoneham's=76 * Default Settings
#define DEFAULT_MAX_FEEDRATE {500, 500, 5, 25} // (mm/sec) *
#define DEFAULT_MAX_ACCELERATION {800, 800, 100, 10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. * These settings can be reset by M502
*
* Note that if EEPROM is enabled, saved values will override these.
*/
#define DEFAULT_ACCELERATION 600 // X, Y, Z and E acceleration in mm/s^2 for printing moves /**
#define DEFAULT_RETRACT_ACCELERATION 1000 // E acceleration in mm/s^2 for retracts * Default Axis Steps Per Unit (steps/mm)
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves * Override with M92
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 44.3090, 22.1545, 1600, 53.5 } // default steps per unit for RigidBot with standard hardware
// default steps for 16-tooth pulleys { 100.06, 50.06, 1600, 76 }, HPX2-MAX E=504, RigidBot E=53.5, Peter Stoneham's=76
// "Jerk" specifies the minimum speed change that requires acceleration. /**
// When changing speed and direction, if the difference is less than the * Default Max Feed Rate (mm/s)
// value set here, it may happen instantaneously. * Override with M203
#define DEFAULT_XYJERK 8.0 // (mm/sec) */
#define DEFAULT_ZJERK 0.4 // (mm/sec) #define DEFAULT_MAX_FEEDRATE { 500, 500, 5, 25 }
#define DEFAULT_EJERK 5.0 // (mm/sec)
/**
* Default Max Acceleration (change/s) change = mm/s
* Override with M201
*
* Maximum start speed for accelerated moves: { X, Y, Z, E }
*/
#define DEFAULT_MAX_ACCELERATION { 800, 800, 100, 10000 }
/**
* Default Acceleration (change/s) change = mm/s
* Override with M204
*
* M204 P Acceleration
* M204 R Retract Acceleration
* M204 T Travel Acceleration
*/
#define DEFAULT_ACCELERATION 600 // X, Y, Z and E acceleration for printing moves
#define DEFAULT_RETRACT_ACCELERATION 1000 // E acceleration for retracts
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves
/**
* Defult Jerk (mm/s)
*
* "Jerk" specifies the minimum speed change that requires acceleration.
* When changing speed and direction, if the difference is less than the
* value set here, it may happen instantaneously.
*/
#define DEFAULT_XYJERK 8.0
#define DEFAULT_ZJERK 0.4
#define DEFAULT_EJERK 5.0
//=========================================================================== //===========================================================================

61
Marlin/example_configurations/SCARA/Configuration.h
View file

@ -365,8 +365,9 @@
#define EXTRUDE_MINTEMP 170 #define EXTRUDE_MINTEMP 170
// This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH.
// Note that for Bowden Extruders a too-small value here may prevent loading.
#define PREVENT_LENGTHY_EXTRUDE #define PREVENT_LENGTHY_EXTRUDE
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) #define EXTRUDE_MAXLENGTH 200
//=========================================================================== //===========================================================================
//======================== Thermal Runaway Protection ======================= //======================== Thermal Runaway Protection =======================
@ -446,20 +447,56 @@
//============================================================================= //=============================================================================
// @section motion // @section motion
/**
* Default Settings
*
* These settings can be reset by M502
*
* Note that if EEPROM is enabled, saved values will override these.
*/
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT {103.69,106.65,200/1.25,1000} // default steps per unit for SCARA #define DEFAULT_AXIS_STEPS_PER_UNIT {103.69,106.65,200/1.25,1000} // default steps per unit for SCARA
#define DEFAULT_MAX_FEEDRATE {300, 300, 30, 25} // (mm/sec)
#define DEFAULT_MAX_ACCELERATION {300,300,20,1000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
#define DEFAULT_ACCELERATION 400 // X, Y, Z and E acceleration in mm/s^2 for printing moves /**
#define DEFAULT_RETRACT_ACCELERATION 2000 // E acceleration in mm/s^2 for retracts * Default Max Feed Rate (mm/s)
#define DEFAULT_TRAVEL_ACCELERATION 400 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves * Override with M203
*/
#define DEFAULT_MAX_FEEDRATE { 300, 300, 30, 25 }
// "Jerk" specifies the minimum speed change that requires acceleration. /**
// When changing speed and direction, if the difference is less than the * Default Max Acceleration (change/s) change = mm/s
// value set here, it may happen instantaneously. * Override with M201
#define DEFAULT_XYJERK 5.0 // (mm/sec) *
#define DEFAULT_ZJERK 0.4 // (mm/sec) * Maximum start speed for accelerated moves: { X, Y, Z, E }
#define DEFAULT_EJERK 3.0 // (mm/sec) */
#define DEFAULT_MAX_ACCELERATION { 300, 300, 20, 1000 }
/**
* Default Acceleration (change/s) change = mm/s
* Override with M204
*
* M204 P Acceleration
* M204 R Retract Acceleration
* M204 T Travel Acceleration
*/
#define DEFAULT_ACCELERATION 400 // X, Y, Z and E acceleration for printing moves
#define DEFAULT_RETRACT_ACCELERATION 2000 // E acceleration for retracts
#define DEFAULT_TRAVEL_ACCELERATION 400 // X, Y, Z acceleration for travel (non printing) moves
/**
* Defult Jerk (mm/s)
*
* "Jerk" specifies the minimum speed change that requires acceleration.
* When changing speed and direction, if the difference is less than the
* value set here, it may happen instantaneously.
*/
#define DEFAULT_XYJERK 5.0
#define DEFAULT_ZJERK 0.4
#define DEFAULT_EJERK 3.0
//=========================================================================== //===========================================================================

63
Marlin/example_configurations/TAZ4/Configuration.h
View file

@ -376,8 +376,9 @@
#define EXTRUDE_MINTEMP 170 #define EXTRUDE_MINTEMP 170
// This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH.
// Note that for Bowden Extruders a too-small value here may prevent loading.
#define PREVENT_LENGTHY_EXTRUDE #define PREVENT_LENGTHY_EXTRUDE
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) #define EXTRUDE_MAXLENGTH 200
//=========================================================================== //===========================================================================
//======================== Thermal Runaway Protection ======================= //======================== Thermal Runaway Protection =======================
@ -457,20 +458,56 @@
//============================================================================= //=============================================================================
// @section motion // @section motion
#define DEFAULT_AXIS_STEPS_PER_UNIT {100.5,100.5,400,850} // default steps per unit for Ultimaker /**
#define DEFAULT_MAX_FEEDRATE {800, 800, 8, 50} // (mm/sec) * Default Settings
#define DEFAULT_MAX_ACCELERATION {9000,9000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. *
* These settings can be reset by M502
*
* Note that if EEPROM is enabled, saved values will override these.
*/
#define DEFAULT_ACCELERATION 500 // X, Y, Z and E acceleration in mm/s^2 for printing moves /**
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts * Default Axis Steps Per Unit (steps/mm)
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves * Override with M92
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 100.5, 100.5, 400, 850 }
// "Jerk" specifies the minimum speed change that requires acceleration. /**
// When changing speed and direction, if the difference is less than the * Default Max Feed Rate (mm/s)
// value set here, it may happen instantaneously. * Override with M203
#define DEFAULT_XYJERK 8.0 // (mm/sec) */
#define DEFAULT_ZJERK 0.4 // (mm/sec) #define DEFAULT_MAX_FEEDRATE { 800, 800, 8, 50 }
#define DEFAULT_EJERK 10.0 // (mm/sec)
/**
* Default Max Acceleration (change/s) change = mm/s
* Override with M201
*
* Maximum start speed for accelerated moves: { X, Y, Z, E }
*/
#define DEFAULT_MAX_ACCELERATION { 9000, 9000, 100, 10000 }
/**
* Default Acceleration (change/s) change = mm/s
* Override with M204
*
* M204 P Acceleration
* M204 R Retract Acceleration
* M204 T Travel Acceleration
*/
#define DEFAULT_ACCELERATION 500 // X, Y, Z and E acceleration for printing moves
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves
/**
* Defult Jerk (mm/s)
*
* "Jerk" specifies the minimum speed change that requires acceleration.
* When changing speed and direction, if the difference is less than the
* value set here, it may happen instantaneously.
*/
#define DEFAULT_XYJERK 8.0
#define DEFAULT_ZJERK 0.4
#define DEFAULT_EJERK 10.0
//=========================================================================== //===========================================================================

63
Marlin/example_configurations/WITBOX/Configuration.h
View file

@ -347,8 +347,9 @@
#define EXTRUDE_MINTEMP 170 #define EXTRUDE_MINTEMP 170
// This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH.
// Note that for Bowden Extruders a too-small value here may prevent loading.
#define PREVENT_LENGTHY_EXTRUDE #define PREVENT_LENGTHY_EXTRUDE
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) #define EXTRUDE_MAXLENGTH 200
//=========================================================================== //===========================================================================
//======================== Thermal Runaway Protection ======================= //======================== Thermal Runaway Protection =======================
@ -428,20 +429,56 @@
//============================================================================= //=============================================================================
// @section motion // @section motion
#define DEFAULT_AXIS_STEPS_PER_UNIT {80,80,600.0*8/3,102.073} // default steps per unit for Ultimaker /**
#define DEFAULT_MAX_FEEDRATE {350, 350, 7.2, 80} // (mm/sec) * Default Settings
#define DEFAULT_MAX_ACCELERATION {1000,1000,10,1000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. *
* These settings can be reset by M502
*
* Note that if EEPROM is enabled, saved values will override these.
*/
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves /**
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts * Default Axis Steps Per Unit (steps/mm)
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves * Override with M92
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT {80,80,600.0*8/3,102.073}
// "Jerk" specifies the minimum speed change that requires acceleration. /**
// When changing speed and direction, if the difference is less than the * Default Max Feed Rate (mm/s)
// value set here, it may happen instantaneously. * Override with M203
#define DEFAULT_XYJERK 10.0 // (mm/sec) */
#define DEFAULT_ZJERK 0.4 // (mm/sec) #define DEFAULT_MAX_FEEDRATE { 350, 350, 7.2, 80 }
#define DEFAULT_EJERK 5.0 // (mm/sec)
/**
* Default Max Acceleration (change/s) change = mm/s
* Override with M201
*
* Maximum start speed for accelerated moves: { X, Y, Z, E }
*/
#define DEFAULT_MAX_ACCELERATION { 1000, 1000, 10, 1000 }
/**
* Default Acceleration (change/s) change = mm/s
* Override with M204
*
* M204 P Acceleration
* M204 R Retract Acceleration
* M204 T Travel Acceleration
*/
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves
/**
* Defult Jerk (mm/s)
*
* "Jerk" specifies the minimum speed change that requires acceleration.
* When changing speed and direction, if the difference is less than the
* value set here, it may happen instantaneously.
*/
#define DEFAULT_XYJERK 10.0
#define DEFAULT_ZJERK 0.4
#define DEFAULT_EJERK 5.0
//=========================================================================== //===========================================================================

63
Marlin/example_configurations/adafruit/ST7565/Configuration.h
View file

@ -355,8 +355,9 @@
#define EXTRUDE_MINTEMP 170 #define EXTRUDE_MINTEMP 170
// This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH.
// Note that for Bowden Extruders a too-small value here may prevent loading.
#define PREVENT_LENGTHY_EXTRUDE #define PREVENT_LENGTHY_EXTRUDE
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) #define EXTRUDE_MAXLENGTH 200
//=========================================================================== //===========================================================================
//======================== Thermal Runaway Protection ======================= //======================== Thermal Runaway Protection =======================
@ -436,20 +437,56 @@
//============================================================================= //=============================================================================
// @section motion // @section motion
#define DEFAULT_AXIS_STEPS_PER_UNIT {80,80,4000,500} // default steps per unit for Ultimaker /**
#define DEFAULT_MAX_FEEDRATE {300, 300, 5, 25} // (mm/sec) * Default Settings
#define DEFAULT_MAX_ACCELERATION {3000,3000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. *
* These settings can be reset by M502
*
* Note that if EEPROM is enabled, saved values will override these.
*/
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves /**
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts * Default Axis Steps Per Unit (steps/mm)
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves * Override with M92
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 4000, 500 }
// "Jerk" specifies the minimum speed change that requires acceleration. /**
// When changing speed and direction, if the difference is less than the * Default Max Feed Rate (mm/s)
// value set here, it may happen instantaneously. * Override with M203
#define DEFAULT_XYJERK 20.0 // (mm/sec) */
#define DEFAULT_ZJERK 0.4 // (mm/sec) #define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 }
#define DEFAULT_EJERK 5.0 // (mm/sec)
/**
* Default Max Acceleration (change/s) change = mm/s
* Override with M201
*
* Maximum start speed for accelerated moves: { X, Y, Z, E }
*/
#define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 }
/**
* Default Acceleration (change/s) change = mm/s
* Override with M204
*
* M204 P Acceleration
* M204 R Retract Acceleration
* M204 T Travel Acceleration
*/
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves
/**
* Defult Jerk (mm/s)
*
* "Jerk" specifies the minimum speed change that requires acceleration.
* When changing speed and direction, if the difference is less than the
* value set here, it may happen instantaneously.
*/
#define DEFAULT_XYJERK 20.0
#define DEFAULT_ZJERK 0.4
#define DEFAULT_EJERK 5.0
//=========================================================================== //===========================================================================

63
Marlin/example_configurations/delta/biv2.5/Configuration.h
View file

@ -355,8 +355,9 @@
#define EXTRUDE_MINTEMP 170 #define EXTRUDE_MINTEMP 170
// This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH.
// Note that for Bowden Extruders a too-small value here may prevent loading.
#define PREVENT_LENGTHY_EXTRUDE #define PREVENT_LENGTHY_EXTRUDE
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) #define EXTRUDE_MAXLENGTH 200
//=========================================================================== //===========================================================================
//======================== Thermal Runaway Protection ======================= //======================== Thermal Runaway Protection =======================
@ -479,20 +480,56 @@
// @section motion // @section motion
// delta speeds must be the same on xyz // delta speeds must be the same on xyz
#define DEFAULT_AXIS_STEPS_PER_UNIT {72.9, 72.9, 72.9, 291} // default steps per unit for BI v2.5 (cable drive) /**
#define DEFAULT_MAX_FEEDRATE {500, 500, 500, 150} // (mm/sec) * Default Settings
#define DEFAULT_MAX_ACCELERATION {9000,9000,9000,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. *
* These settings can be reset by M502
*
* Note that if EEPROM is enabled, saved values will override these.
*/
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves /**
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts * Default Axis Steps Per Unit (steps/mm)
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves * Override with M92
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 72.9, 72.9, 72.9, 291 } // default steps per unit for BI v2.5 (cable drive)
// "Jerk" specifies the minimum speed change that requires acceleration. /**
// When changing speed and direction, if the difference is less than the * Default Max Feed Rate (mm/s)
// value set here, it may happen instantaneously. * Override with M203
#define DEFAULT_XYJERK 15.0 // (mm/sec) */
#define DEFAULT_ZJERK 15.0 // (mm/sec) Must be same as XY for delta #define DEFAULT_MAX_FEEDRATE { 500, 500, 500, 150 }
#define DEFAULT_EJERK 5.0 // (mm/sec)
/**
* Default Max Acceleration (change/s) change = mm/s
* Override with M201
*
* Maximum start speed for accelerated moves: { X, Y, Z, E }
*/
#define DEFAULT_MAX_ACCELERATION { 9000, 9000, 9000, 10000 }
/**
* Default Acceleration (change/s) change = mm/s
* Override with M204
*
* M204 P Acceleration
* M204 R Retract Acceleration
* M204 T Travel Acceleration
*/
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves
/**
* Defult Jerk (mm/s)
*
* "Jerk" specifies the minimum speed change that requires acceleration.
* When changing speed and direction, if the difference is less than the
* value set here, it may happen instantaneously.
*/
#define DEFAULT_XYJERK 15.0
#define DEFAULT_ZJERK 15.0 // Must be same as XY for delta
#define DEFAULT_EJERK 5.0
//=========================================================================== //===========================================================================

61
Marlin/example_configurations/delta/generic/Configuration.h
View file

@ -355,8 +355,9 @@
#define EXTRUDE_MINTEMP 170 #define EXTRUDE_MINTEMP 170
// This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH.
// Note that for Bowden Extruders a too-small value here may prevent loading.
#define PREVENT_LENGTHY_EXTRUDE #define PREVENT_LENGTHY_EXTRUDE
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) #define EXTRUDE_MAXLENGTH 200
//=========================================================================== //===========================================================================
//======================== Thermal Runaway Protection ======================= //======================== Thermal Runaway Protection =======================
@ -479,20 +480,56 @@
// @section motion // @section motion
// delta speeds must be the same on xyz // delta speeds must be the same on xyz
/**
* Default Settings
*
* These settings can be reset by M502
*
* Note that if EEPROM is enabled, saved values will override these.
*/
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT {80, 80, 80, 760*1.1} // default steps per unit for Kossel (GT2, 20 tooth) #define DEFAULT_AXIS_STEPS_PER_UNIT {80, 80, 80, 760*1.1} // default steps per unit for Kossel (GT2, 20 tooth)
#define DEFAULT_MAX_FEEDRATE {500, 500, 500, 25} // (mm/sec)
#define DEFAULT_MAX_ACCELERATION {9000,9000,9000,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves /**
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts * Default Max Feed Rate (mm/s)
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves * Override with M203
*/
#define DEFAULT_MAX_FEEDRATE { 500, 500, 500, 25 }
// "Jerk" specifies the minimum speed change that requires acceleration. /**
// When changing speed and direction, if the difference is less than the * Default Max Acceleration (change/s) change = mm/s
// value set here, it may happen instantaneously. * Override with M201
#define DEFAULT_XYJERK 20.0 // (mm/sec) *
#define DEFAULT_ZJERK 20.0 // (mm/sec) Must be same as XY for delta * Maximum start speed for accelerated moves: { X, Y, Z, E }
#define DEFAULT_EJERK 5.0 // (mm/sec) */
#define DEFAULT_MAX_ACCELERATION { 9000, 9000, 9000, 10000 }
/**
* Default Acceleration (change/s) change = mm/s
* Override with M204
*
* M204 P Acceleration
* M204 R Retract Acceleration
* M204 T Travel Acceleration
*/
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves
/**
* Defult Jerk (mm/s)
*
* "Jerk" specifies the minimum speed change that requires acceleration.
* When changing speed and direction, if the difference is less than the
* value set here, it may happen instantaneously.
*/
#define DEFAULT_XYJERK 20.0
#define DEFAULT_ZJERK 20.0 // Must be same as XY for delta
#define DEFAULT_EJERK 5.0
//=========================================================================== //===========================================================================

61
Marlin/example_configurations/delta/kossel_mini/Configuration.h
View file

@ -355,8 +355,9 @@
#define EXTRUDE_MINTEMP 170 #define EXTRUDE_MINTEMP 170
// This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH.
// Note that for Bowden Extruders a too-small value here may prevent loading.
#define PREVENT_LENGTHY_EXTRUDE #define PREVENT_LENGTHY_EXTRUDE
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) #define EXTRUDE_MAXLENGTH 200
//=========================================================================== //===========================================================================
//======================== Thermal Runaway Protection ======================= //======================== Thermal Runaway Protection =======================
@ -479,20 +480,56 @@
// @section motion // @section motion
// delta speeds must be the same on xyz // delta speeds must be the same on xyz
/**
* Default Settings
*
* These settings can be reset by M502
*
* Note that if EEPROM is enabled, saved values will override these.
*/
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT {80, 80, 80, 760*1.1} // default steps per unit for Kossel (GT2, 20 tooth) #define DEFAULT_AXIS_STEPS_PER_UNIT {80, 80, 80, 760*1.1} // default steps per unit for Kossel (GT2, 20 tooth)
#define DEFAULT_MAX_FEEDRATE {500, 500, 500, 25} // (mm/sec)
#define DEFAULT_MAX_ACCELERATION {9000,9000,9000,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves /**
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts * Default Max Feed Rate (mm/s)
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves * Override with M203
*/
#define DEFAULT_MAX_FEEDRATE { 500, 500, 500, 25 }
// "Jerk" specifies the minimum speed change that requires acceleration. /**
// When changing speed and direction, if the difference is less than the * Default Max Acceleration (change/s) change = mm/s
// value set here, it may happen instantaneously. * Override with M201
#define DEFAULT_XYJERK 20.0 // (mm/sec) *
#define DEFAULT_ZJERK 20.0 // (mm/sec) Must be same as XY for delta * Maximum start speed for accelerated moves: { X, Y, Z, E }
#define DEFAULT_EJERK 5.0 // (mm/sec) */
#define DEFAULT_MAX_ACCELERATION { 9000, 9000, 9000, 10000 }
/**
* Default Acceleration (change/s) change = mm/s
* Override with M204
*
* M204 P Acceleration
* M204 R Retract Acceleration
* M204 T Travel Acceleration
*/
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves
/**
* Defult Jerk (mm/s)
*
* "Jerk" specifies the minimum speed change that requires acceleration.
* When changing speed and direction, if the difference is less than the
* value set here, it may happen instantaneously.
*/
#define DEFAULT_XYJERK 20.0
#define DEFAULT_ZJERK 20.0 // Must be same as XY for delta
#define DEFAULT_EJERK 5.0
//=========================================================================== //===========================================================================

61
Marlin/example_configurations/delta/kossel_pro/Configuration.h
View file

@ -344,8 +344,9 @@
#define EXTRUDE_MINTEMP 170 #define EXTRUDE_MINTEMP 170
// This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH.
// Note that for Bowden Extruders a too-small value here may prevent loading.
#define PREVENT_LENGTHY_EXTRUDE #define PREVENT_LENGTHY_EXTRUDE
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) #define EXTRUDE_MAXLENGTH 200
//=========================================================================== //===========================================================================
//======================== Thermal Runaway Protection ======================= //======================== Thermal Runaway Protection =======================
@ -475,20 +476,56 @@
// delta speeds must be the same on xyz // delta speeds must be the same on xyz
#define XYZ_STEPS ((XYZ_FULL_STEPS_PER_ROTATION) * (XYZ_MICROSTEPS) / double(XYZ_BELT_PITCH) / double(XYZ_PULLEY_TEETH)) #define XYZ_STEPS ((XYZ_FULL_STEPS_PER_ROTATION) * (XYZ_MICROSTEPS) / double(XYZ_BELT_PITCH) / double(XYZ_PULLEY_TEETH))
/**
* Default Settings
*
* These settings can be reset by M502
*
* Note that if EEPROM is enabled, saved values will override these.
*/
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT {XYZ_STEPS, XYZ_STEPS, XYZ_STEPS, 184.8} #define DEFAULT_AXIS_STEPS_PER_UNIT {XYZ_STEPS, XYZ_STEPS, XYZ_STEPS, 184.8}
#define DEFAULT_MAX_FEEDRATE {200, 200, 200, 200} // (mm/sec)
#define DEFAULT_MAX_ACCELERATION {9000,9000,9000,9000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves /**
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts * Default Max Feed Rate (mm/s)
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves * Override with M203
*/
#define DEFAULT_MAX_FEEDRATE { 200, 200, 200, 200 }
// "Jerk" specifies the minimum speed change that requires acceleration. /**
// When changing speed and direction, if the difference is less than the * Default Max Acceleration (change/s) change = mm/s
// value set here, it may happen instantaneously. * Override with M201
#define DEFAULT_XYJERK 20.0 // (mm/sec) *
#define DEFAULT_ZJERK 20.0 // (mm/sec) Must be same as XY for delta * Maximum start speed for accelerated moves: { X, Y, Z, E }
#define DEFAULT_EJERK 5.0 // (mm/sec) */
#define DEFAULT_MAX_ACCELERATION { 9000, 9000, 9000, 9000 }
/**
* Default Acceleration (change/s) change = mm/s
* Override with M204
*
* M204 P Acceleration
* M204 R Retract Acceleration
* M204 T Travel Acceleration
*/
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves
/**
* Defult Jerk (mm/s)
*
* "Jerk" specifies the minimum speed change that requires acceleration.
* When changing speed and direction, if the difference is less than the
* value set here, it may happen instantaneously.
*/
#define DEFAULT_XYJERK 20.0
#define DEFAULT_ZJERK 20.0 // Must be same as XY for delta
#define DEFAULT_EJERK 5.0
//=========================================================================== //===========================================================================

61
Marlin/example_configurations/delta/kossel_xl/Configuration.h
View file

@ -353,8 +353,9 @@
#define EXTRUDE_MINTEMP 170 #define EXTRUDE_MINTEMP 170
// This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH.
// Note that for Bowden Extruders a too-small value here may prevent loading.
#define PREVENT_LENGTHY_EXTRUDE #define PREVENT_LENGTHY_EXTRUDE
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) #define EXTRUDE_MAXLENGTH 200
//=========================================================================== //===========================================================================
//======================== Thermal Runaway Protection ======================= //======================== Thermal Runaway Protection =======================
@ -485,20 +486,56 @@
// delta speeds must be the same on xyz // delta speeds must be the same on xyz
#define XYZ_STEPS (XYZ_FULL_STEPS_PER_ROTATION * XYZ_MICROSTEPS / double(XYZ_BELT_PITCH) / double(XYZ_PULLEY_TEETH)) #define XYZ_STEPS (XYZ_FULL_STEPS_PER_ROTATION * XYZ_MICROSTEPS / double(XYZ_BELT_PITCH) / double(XYZ_PULLEY_TEETH))
/**
* Default Settings
*
* These settings can be reset by M502
*
* Note that if EEPROM is enabled, saved values will override these.
*/
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT {XYZ_STEPS, XYZ_STEPS, XYZ_STEPS, 158} // default steps per unit for PowerWasp #define DEFAULT_AXIS_STEPS_PER_UNIT {XYZ_STEPS, XYZ_STEPS, XYZ_STEPS, 158} // default steps per unit for PowerWasp
#define DEFAULT_MAX_FEEDRATE {200, 200, 200, 25} // (mm/sec)
#define DEFAULT_MAX_ACCELERATION {9000,9000,9000,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot.
#define DEFAULT_ACCELERATION 2000 // X, Y, Z and E acceleration in mm/s^2 for printing moves /**
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts * Default Max Feed Rate (mm/s)
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves * Override with M203
*/
#define DEFAULT_MAX_FEEDRATE { 200, 200, 200, 25 }
// "Jerk" specifies the minimum speed change that requires acceleration. /**
// When changing speed and direction, if the difference is less than the * Default Max Acceleration (change/s) change = mm/s
// value set here, it may happen instantaneously. * Override with M201
#define DEFAULT_XYJERK 20.0 // (mm/sec) *
#define DEFAULT_ZJERK 20.0 // (mm/sec) * Maximum start speed for accelerated moves: { X, Y, Z, E }
#define DEFAULT_EJERK 20.0 // (mm/sec) */
#define DEFAULT_MAX_ACCELERATION { 9000, 9000, 9000, 10000 }
/**
* Default Acceleration (change/s) change = mm/s
* Override with M204
*
* M204 P Acceleration
* M204 R Retract Acceleration
* M204 T Travel Acceleration
*/
#define DEFAULT_ACCELERATION 2000 // X, Y, Z and E acceleration for printing moves
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves
/**
* Defult Jerk (mm/s)
*
* "Jerk" specifies the minimum speed change that requires acceleration.
* When changing speed and direction, if the difference is less than the
* value set here, it may happen instantaneously.
*/
#define DEFAULT_XYJERK 20.0
#define DEFAULT_ZJERK 20.0
#define DEFAULT_EJERK 20.0
//=========================================================================== //===========================================================================

63
Marlin/example_configurations/makibox/Configuration.h
View file

@ -358,8 +358,9 @@
#define EXTRUDE_MINTEMP 170 #define EXTRUDE_MINTEMP 170
// This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH.
// Note that for Bowden Extruders a too-small value here may prevent loading.
#define PREVENT_LENGTHY_EXTRUDE #define PREVENT_LENGTHY_EXTRUDE
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) #define EXTRUDE_MAXLENGTH 200
//=========================================================================== //===========================================================================
//======================== Thermal Runaway Protection ======================= //======================== Thermal Runaway Protection =======================
@ -439,20 +440,56 @@
//============================================================================= //=============================================================================
// @section motion // @section motion
#define DEFAULT_AXIS_STEPS_PER_UNIT {400, 400, 400, 163} // default steps per unit for ***** MakiBox A6 ***** /**
#define DEFAULT_MAX_FEEDRATE {60, 60, 20, 45} // (mm/sec) * Default Settings
#define DEFAULT_MAX_ACCELERATION {2000,2000,30,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. *
* These settings can be reset by M502
*
* Note that if EEPROM is enabled, saved values will override these.
*/
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration in mm/s^2 for printing moves /**
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts * Default Axis Steps Per Unit (steps/mm)
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves * Override with M92
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 400, 400, 400, 163 } // default steps per unit for ***** MakiBox A6 *****
// "Jerk" specifies the minimum speed change that requires acceleration. /**
// When changing speed and direction, if the difference is less than the * Default Max Feed Rate (mm/s)
// value set here, it may happen instantaneously. * Override with M203
#define DEFAULT_XYJERK 20.0 // (mm/sec) */
#define DEFAULT_ZJERK 0.4 // (mm/sec) #define DEFAULT_MAX_FEEDRATE { 60, 60, 20, 45 }
#define DEFAULT_EJERK 5.0 // (mm/sec)
/**
* Default Max Acceleration (change/s) change = mm/s
* Override with M201
*
* Maximum start speed for accelerated moves: { X, Y, Z, E }
*/
#define DEFAULT_MAX_ACCELERATION { 2000, 2000, 30, 10000 }
/**
* Default Acceleration (change/s) change = mm/s
* Override with M204
*
* M204 P Acceleration
* M204 R Retract Acceleration
* M204 T Travel Acceleration
*/
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves
/**
* Defult Jerk (mm/s)
*
* "Jerk" specifies the minimum speed change that requires acceleration.
* When changing speed and direction, if the difference is less than the
* value set here, it may happen instantaneously.
*/
#define DEFAULT_XYJERK 20.0
#define DEFAULT_ZJERK 0.4
#define DEFAULT_EJERK 5.0
//=========================================================================== //===========================================================================

2
Marlin/example_configurations/makibox/Configuration_adv.h
View file

@ -389,7 +389,7 @@
// Number of channels available for I2C digipot, For Azteeg X3 Pro we have 8 // Number of channels available for I2C digipot, For Azteeg X3 Pro we have 8
#define DIGIPOT_I2C_NUM_CHANNELS 4 #define DIGIPOT_I2C_NUM_CHANNELS 4
// actual motor currents in Amps, need as many here as DIGIPOT_I2C_NUM_CHANNELS // actual motor currents in Amps, need as many here as DIGIPOT_I2C_NUM_CHANNELS
#define DIGIPOT_I2C_MOTOR_CURRENTS {1.7, 1.7, 1.7, 1.7} #define DIGIPOT_I2C_MOTOR_CURRENTS { 1.7, 1.7, 1.7, 1.7 }
//=========================================================================== //===========================================================================
//=============================Additional Features=========================== //=============================Additional Features===========================

69
Marlin/example_configurations/tvrrug/Round2/Configuration.h
View file

@ -345,8 +345,9 @@
#define EXTRUDE_MINTEMP 170 #define EXTRUDE_MINTEMP 170
// This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. // This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH.
// Note that for Bowden Extruders a too-small value here may prevent loading.
#define PREVENT_LENGTHY_EXTRUDE #define PREVENT_LENGTHY_EXTRUDE
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) #define EXTRUDE_MAXLENGTH 200
//=========================================================================== //===========================================================================
//======================== Thermal Runaway Protection ======================= //======================== Thermal Runaway Protection =======================
@ -426,24 +427,62 @@
//============================================================================= //=============================================================================
// @section motion // @section motion
/**
* Default Settings
*
* These settings can be reset by M502
*
* Note that if EEPROM is enabled, saved values will override these.
*/
/**
* Default Axis Steps Per Unit (steps/mm)
* Override with M92
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 71.1, 71.1, 2560, 600 } // David TVRR
//#define DEFAULT_AXIS_STEPS_PER_UNIT {79.87, 79.87, 2566, 563,78} // Al's TVRR //#define DEFAULT_AXIS_STEPS_PER_UNIT {79.87, 79.87, 2566, 563,78} // Al's TVRR
//#define DEFAULT_AXIS_STEPS_PER_UNIT {81.26, 80.01, 2561, 599.14} // Michel TVRR old //#define DEFAULT_AXIS_STEPS_PER_UNIT { 81.26, 80.01, 2561, 599.14 } // Michel TVRR old
//#define DEFAULT_AXIS_STEPS_PER_UNIT {71.1, 71.1, 2560, 739.65} // Michel TVRR //#define DEFAULT_AXIS_STEPS_PER_UNIT { 71.1, 71.1, 2560, 739.65 } // Michel TVRR
#define DEFAULT_AXIS_STEPS_PER_UNIT {71.1, 71.1, 2560, 600} // David TVRR
#define DEFAULT_MAX_FEEDRATE {500, 500, 5, 45} // (mm/sec) David TVRR /**
#define DEFAULT_MAX_ACCELERATION {9000,9000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. * Default Max Feed Rate (mm/s)
* Override with M203
*/
#define DEFAULT_MAX_FEEDRATE { 500, 500, 5, 45 } // David TVRR
/**
* Default Max Acceleration (change/s) change = mm/s
* Override with M201
*
* Maximum start speed for accelerated moves: { X, Y, Z, E }
*/
#define DEFAULT_MAX_ACCELERATION { 9000, 9000, 100, 10000 }
/* MICHEL: This has an impact on the "ripples" in print walls */ /* MICHEL: This has an impact on the "ripples" in print walls */
#define DEFAULT_ACCELERATION 500 // X, Y, Z and E acceleration in mm/s^2 for printing moves
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts
#define DEFAULT_TRAVEL_ACCELERATION 500 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves
// "Jerk" specifies the minimum speed change that requires acceleration. /**
// When changing speed and direction, if the difference is less than the * Default Acceleration (change/s) change = mm/s
// value set here, it may happen instantaneously. * Override with M204
#define DEFAULT_XYJERK 20.0 // (mm/sec) *
#define DEFAULT_ZJERK 0.4 // (mm/sec) * M204 P Acceleration
#define DEFAULT_EJERK 5.0 // (mm/sec) * M204 R Retract Acceleration
* M204 T Travel Acceleration
*/
#define DEFAULT_ACCELERATION 500 // X, Y, Z and E acceleration for printing moves
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts
#define DEFAULT_TRAVEL_ACCELERATION 500 // X, Y, Z acceleration for travel (non printing) moves
/**
* Defult Jerk (mm/s)
*
* "Jerk" specifies the minimum speed change that requires acceleration.
* When changing speed and direction, if the difference is less than the
* value set here, it may happen instantaneously.
*/
#define DEFAULT_XYJERK 20.0
#define DEFAULT_ZJERK 0.4
#define DEFAULT_EJERK 5.0
//=========================================================================== //===========================================================================

2
Marlin/pins_PRINTRBOARD_REVF.h
View file

@ -83,7 +83,7 @@
// uncomment to enable an I2C based DAC like on the Printrboard REVF // uncomment to enable an I2C based DAC like on the Printrboard REVF
#define DAC_STEPPER_CURRENT #define DAC_STEPPER_CURRENT
// Number of channels available for DAC, For Printrboar REVF there are 4 // Number of channels available for DAC, For Printrboar REVF there are 4
#define DAC_STEPPER_ORDER {3,2,1,0} #define DAC_STEPPER_ORDER { 3, 2, 1, 0 }
#define DAC_STEPPER_SENSE 0.11 #define DAC_STEPPER_SENSE 0.11
#define DAC_STEPPER_ADDRESS 0 #define DAC_STEPPER_ADDRESS 0

2
Marlin/pins_RIGIDBOARD_V2.h
View file

@ -32,7 +32,7 @@
// I2C based DAC like on the Printrboard REVF // I2C based DAC like on the Printrboard REVF
#define DAC_STEPPER_CURRENT #define DAC_STEPPER_CURRENT
// Channels available for DAC, For Rigidboard there are 4 // Channels available for DAC, For Rigidboard there are 4
#define DAC_STEPPER_ORDER {0,1,2,3} #define DAC_STEPPER_ORDER { 0, 1, 2, 3 }
#define DAC_STEPPER_SENSE 0.11 #define DAC_STEPPER_SENSE 0.11
#define DAC_STEPPER_ADDRESS 0 #define DAC_STEPPER_ADDRESS 0