MAGNETIC_PARKING_EXTRUDER (#12351)
This commit is contained in:
parent
1bd9a63049
commit
524c6c10bf
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
/**
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -148,7 +148,7 @@
|
||||||
#include "feature/fanmux.h"
|
#include "feature/fanmux.h"
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
#if DO_SWITCH_EXTRUDER || ENABLED(SWITCHING_NOZZLE) || ENABLED(PARKING_EXTRUDER)
|
#if DO_SWITCH_EXTRUDER || ENABLED(SWITCHING_NOZZLE) || ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
#include "module/tool_change.h"
|
#include "module/tool_change.h"
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
@ -975,8 +975,12 @@ void setup() {
|
||||||
#endif
|
#endif
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
#if ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
mpe_settings_init();
|
||||||
|
#endif
|
||||||
|
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
pe_magnet_init();
|
pe_solenoid_init();
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
/**
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,47 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
/**
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -205,16 +205,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -205,16 +205,47 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
/**
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -212,16 +212,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -205,16 +205,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -213,16 +213,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,47 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
/**
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -245,16 +245,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -207,16 +207,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -208,16 +208,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -209,16 +209,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -224,16 +224,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -209,16 +209,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -205,16 +205,47 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
/**
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,47 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
/**
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -207,16 +207,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -235,16 +235,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -226,16 +226,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,47 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
/**
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -224,16 +224,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -223,16 +223,47 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
/**
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -219,16 +219,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -209,16 +209,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,47 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
/**
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -208,16 +208,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -209,16 +209,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -204,16 +204,48 @@
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Two separate X-carriages with extruders that connect to a moving part
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
* via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
* via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN.
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
*/
|
*/
|
||||||
//#define PARKING_EXTRUDER
|
//#define PARKING_EXTRUDER
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
|
||||||
|
/**
|
||||||
|
* Two separate X-carriages with extruders that connect to a moving part
|
||||||
|
* via a magnetic docking mechanism using movements and no solenoid
|
||||||
|
*
|
||||||
|
* project : https://www.thingiverse.com/thing:3080893
|
||||||
|
* movements : https://youtu.be/0xCEiG9VS3k
|
||||||
|
* https://youtu.be/Bqbcs0CU2FE
|
||||||
|
*
|
||||||
|
* for cooling multi extruder with separate fans
|
||||||
|
* see on Configuration_adv.h and look for "Part-Cooling"
|
||||||
|
*/
|
||||||
|
//#define MAGNETIC_PARKING_EXTRUDER
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER) || ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
||||||
|
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder
|
||||||
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
#define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
#define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil
|
||||||
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined.
|
#define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined.
|
||||||
#define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders
|
|
||||||
#define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder
|
|
||||||
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
//#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381
|
||||||
|
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point
|
||||||
|
#define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple
|
||||||
|
#define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point
|
||||||
|
#define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -705,6 +705,10 @@ void GcodeSuite::process_parsed_command(
|
||||||
case 869: M869(); break; // M869: Report axis error
|
case 869: M869(); break; // M869: Report axis error
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
#if ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
case 951: M951(); break; // M951: Set Magnetic Parking Extruder parameters
|
||||||
|
#endif
|
||||||
|
|
||||||
#if ENABLED(Z_STEPPER_AUTO_ALIGN)
|
#if ENABLED(Z_STEPPER_AUTO_ALIGN)
|
||||||
case 422: M422(); break; // M422: Set Z Stepper automatic alignment position using probe
|
case 422: M422(); break; // M422: Set Z Stepper automatic alignment position using probe
|
||||||
#endif
|
#endif
|
||||||
|
|
|
@ -243,6 +243,7 @@
|
||||||
* M914 - Set StallGuard sensitivity. (Requires SENSORLESS_HOMING or SENSORLESS_PROBING)
|
* M914 - Set StallGuard sensitivity. (Requires SENSORLESS_HOMING or SENSORLESS_PROBING)
|
||||||
* M917 - L6470 tuning: Find minimum current thresholds
|
* M917 - L6470 tuning: Find minimum current thresholds
|
||||||
* M918 - L6470 tuning: Increase speed until max or error
|
* M918 - L6470 tuning: Increase speed until max or error
|
||||||
|
* M951 - Set Magnetic Parking Extruder parameters. (Requires MAGNETIC_PARKING_EXTRUDER)
|
||||||
*
|
*
|
||||||
* M360 - SCARA calibration: Move to cal-position ThetaA (0 deg calibration)
|
* M360 - SCARA calibration: Move to cal-position ThetaA (0 deg calibration)
|
||||||
* M361 - SCARA calibration: Move to cal-position ThetaB (90 deg calibration - steps per degree)
|
* M361 - SCARA calibration: Move to cal-position ThetaB (90 deg calibration - steps per degree)
|
||||||
|
@ -842,6 +843,10 @@ private:
|
||||||
static void M928();
|
static void M928();
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
#if ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
static void M951();
|
||||||
|
#endif
|
||||||
|
|
||||||
static void M999();
|
static void M999();
|
||||||
|
|
||||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||||
|
|
76
Marlin/src/gcode/probe/M951.cpp
Normal file
76
Marlin/src/gcode/probe/M951.cpp
Normal file
|
@ -0,0 +1,76 @@
|
||||||
|
/**
|
||||||
|
* Marlin 3D Printer Firmware
|
||||||
|
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
||||||
|
*
|
||||||
|
* Based on Sprinter and grbl.
|
||||||
|
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
|
||||||
|
*
|
||||||
|
* This program is free software: you can redistribute it and/or modify
|
||||||
|
* it under the terms of the GNU General Public License as published by
|
||||||
|
* the Free Software Foundation, either version 3 of the License, or
|
||||||
|
* (at your option) any later version.
|
||||||
|
*
|
||||||
|
* This program is distributed in the hope that it will be useful,
|
||||||
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||||
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||||
|
* GNU General Public License for more details.
|
||||||
|
*
|
||||||
|
* You should have received a copy of the GNU General Public License
|
||||||
|
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||||
|
*
|
||||||
|
*/
|
||||||
|
|
||||||
|
#include "../../inc/MarlinConfigPre.h"
|
||||||
|
|
||||||
|
#if ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
#include "../gcode.h"
|
||||||
|
#include "../../module/tool_change.h"
|
||||||
|
#include "../../module/motion.h"
|
||||||
|
|
||||||
|
|
||||||
|
mpe_settings_t mpe_settings;
|
||||||
|
|
||||||
|
inline void mpe_settings_report() {
|
||||||
|
SERIAL_ECHO_START(); SERIAL_ECHOLNPGM("Magnetic Parking Extruder");
|
||||||
|
SERIAL_ECHO_START(); SERIAL_ECHOLNPAIR("L: Left parking :", mpe_settings.parking_xpos[0]);
|
||||||
|
SERIAL_ECHO_START(); SERIAL_ECHOLNPAIR("R: Right parking :", mpe_settings.parking_xpos[1]);
|
||||||
|
SERIAL_ECHO_START(); SERIAL_ECHOLNPAIR("I: Grab Offset :", mpe_settings.grab_distance);
|
||||||
|
SERIAL_ECHO_START(); SERIAL_ECHOLNPAIR("J: Normal speed :", long(MMS_TO_MMM(mpe_settings.slow_feedrate)));
|
||||||
|
SERIAL_ECHO_START(); SERIAL_ECHOLNPAIR("H: High speed :", long(MMS_TO_MMM(mpe_settings.fast_feedrate)));
|
||||||
|
SERIAL_ECHO_START(); SERIAL_ECHOLNPAIR("D: Distance trav.:", mpe_settings.travel_distance);
|
||||||
|
SERIAL_ECHO_START(); SERIAL_ECHOLNPAIR("C: Compenstion :", mpe_settings.compensation_factor);
|
||||||
|
}
|
||||||
|
|
||||||
|
void mpe_settings_init() {
|
||||||
|
constexpr float pex[2] = PARKING_EXTRUDER_PARKING_X;
|
||||||
|
mpe_settings.parking_xpos[0] = pex[0]; // M951 L
|
||||||
|
mpe_settings.parking_xpos[1] = pex[1]; // M951 R
|
||||||
|
mpe_settings.grab_distance = PARKING_EXTRUDER_GRAB_DISTANCE; // M951 I
|
||||||
|
#if HAS_HOME_OFFSET
|
||||||
|
set_home_offset(X_AXIS, mpe_settings.grab_distance * -1);
|
||||||
|
#endif
|
||||||
|
mpe_settings.slow_feedrate = MMM_TO_MMS(MPE_SLOW_SPEED); // M951 J
|
||||||
|
mpe_settings.fast_feedrate = MMM_TO_MMS(MPE_FAST_SPEED); // M951 H
|
||||||
|
mpe_settings.travel_distance = MPE_TRAVEL_DISTANCE; // M951 D
|
||||||
|
mpe_settings.compensation_factor = MPE_COMPENSATION; // M951 C
|
||||||
|
mpe_settings_report();
|
||||||
|
}
|
||||||
|
|
||||||
|
void GcodeSuite::M951() {
|
||||||
|
if (parser.seenval('L')) mpe_settings.parking_xpos[0] = parser.value_linear_units();
|
||||||
|
if (parser.seenval('R')) mpe_settings.parking_xpos[1] = parser.value_linear_units();
|
||||||
|
if (parser.seenval('I')) {
|
||||||
|
mpe_settings.grab_distance = parser.value_linear_units();
|
||||||
|
#if HAS_HOME_OFFSET
|
||||||
|
set_home_offset(X_AXIS, mpe_settings.grab_distance * -1);
|
||||||
|
#endif
|
||||||
|
}
|
||||||
|
if (parser.seenval('J')) mpe_settings.slow_feedrate = MMM_TO_MMS(parser.value_linear_units());
|
||||||
|
if (parser.seenval('H')) mpe_settings.fast_feedrate = MMM_TO_MMS(parser.value_linear_units());
|
||||||
|
if (parser.seenval('D')) mpe_settings.travel_distance = parser.value_linear_units();
|
||||||
|
if (parser.seenval('C')) mpe_settings.compensation_factor = parser.value_float();
|
||||||
|
if (!parser.seen("CDHIJLR")) mpe_settings_report();
|
||||||
|
}
|
||||||
|
|
||||||
|
#endif // MAGNETIC_PARKING_EXTRUDER
|
|
@ -791,7 +791,7 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Parking Extruder requirements
|
* (Magnetic) Parking Extruder requirements
|
||||||
*/
|
*/
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
#if ENABLED(PARKING_EXTRUDER)
|
||||||
#if ENABLED(DUAL_X_CARRIAGE)
|
#if ENABLED(DUAL_X_CARRIAGE)
|
||||||
|
@ -800,6 +800,8 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
|
||||||
#error "PARKING_EXTRUDER and SINGLENOZZLE are incompatible."
|
#error "PARKING_EXTRUDER and SINGLENOZZLE are incompatible."
|
||||||
#elif ENABLED(EXT_SOLENOID)
|
#elif ENABLED(EXT_SOLENOID)
|
||||||
#error "PARKING_EXTRUDER and EXT_SOLENOID are incompatible. (Pins are used twice.)"
|
#error "PARKING_EXTRUDER and EXT_SOLENOID are incompatible. (Pins are used twice.)"
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
#error "Enable only one of PARKING_EXTRUDER and MAGNETIC_PARKING_EXTRUDER."
|
||||||
#elif EXTRUDERS != 2
|
#elif EXTRUDERS != 2
|
||||||
#error "PARKING_EXTRUDER requires exactly 2 EXTRUDERS."
|
#error "PARKING_EXTRUDER requires exactly 2 EXTRUDERS."
|
||||||
#elif !PIN_EXISTS(SOL0) || !PIN_EXISTS(SOL1)
|
#elif !PIN_EXISTS(SOL0) || !PIN_EXISTS(SOL1)
|
||||||
|
@ -815,6 +817,22 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
|
||||||
#elif !defined(PARKING_EXTRUDER_SOLENOIDS_DELAY) || !WITHIN(PARKING_EXTRUDER_SOLENOIDS_DELAY, 0, 2000)
|
#elif !defined(PARKING_EXTRUDER_SOLENOIDS_DELAY) || !WITHIN(PARKING_EXTRUDER_SOLENOIDS_DELAY, 0, 2000)
|
||||||
#error "PARKING_EXTRUDER_SOLENOIDS_DELAY must be between 0 and 2000 (ms)."
|
#error "PARKING_EXTRUDER_SOLENOIDS_DELAY must be between 0 and 2000 (ms)."
|
||||||
#endif
|
#endif
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
#if ENABLED(DUAL_X_CARRIAGE)
|
||||||
|
#error "MAGNETIC_PARKING_EXTRUDER and DUAL_X_CARRIAGE are incompatible."
|
||||||
|
#elif ENABLED(SINGLENOZZLE)
|
||||||
|
#error "MAGNETIC_PARKING_EXTRUDER and SINGLENOZZLE are incompatible."
|
||||||
|
#elif ENABLED(EXT_SOLENOID)
|
||||||
|
#error "MAGNETIC_PARKING_EXTRUDER and EXT_SOLENOID are incompatible. (Pins are used twice.)"
|
||||||
|
#elif EXTRUDERS != 2
|
||||||
|
#error "MAGNETIC_PARKING_EXTRUDER requires exactly 2 EXTRUDERS."
|
||||||
|
#elif !defined(PARKING_EXTRUDER_PARKING_X)
|
||||||
|
#error "MAGNETIC_PARKING_EXTRUDER requires PARKING_EXTRUDER_PARKING_X."
|
||||||
|
#elif !defined(TOOLCHANGE_ZRAISE)
|
||||||
|
#error "MAGNETIC_PARKING_EXTRUDER requires TOOLCHANGE_ZRAISE."
|
||||||
|
#elif TOOLCHANGE_ZRAISE < 0
|
||||||
|
#error "TOOLCHANGE_ZRAISE must be 0 or higher."
|
||||||
|
#endif
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
/**
|
||||||
|
|
|
@ -2078,6 +2078,10 @@ void MarlinSettings::reset(PORTARG_SOLO) {
|
||||||
toolchange_settings.z_raise = TOOLCHANGE_ZRAISE;
|
toolchange_settings.z_raise = TOOLCHANGE_ZRAISE;
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
#if ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
mpe_settings_init();
|
||||||
|
#endif
|
||||||
|
|
||||||
//
|
//
|
||||||
// Global Leveling
|
// Global Leveling
|
||||||
//
|
//
|
||||||
|
|
|
@ -42,7 +42,7 @@
|
||||||
#endif
|
#endif
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
#if ENABLED(PARKING_EXTRUDER) && PARKING_EXTRUDER_SOLENOIDS_DELAY > 0
|
#if ENABLED(MAGNETIC_PARKING_EXTRUDER) || (ENABLED(PARKING_EXTRUDER) && PARKING_EXTRUDER_SOLENOIDS_DELAY > 0)
|
||||||
#include "../gcode/gcode.h" // for dwell()
|
#include "../gcode/gcode.h" // for dwell()
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
@ -126,18 +126,143 @@
|
||||||
|
|
||||||
#endif // SWITCHING_NOZZLE
|
#endif // SWITCHING_NOZZLE
|
||||||
|
|
||||||
#if ENABLED(PARKING_EXTRUDER)
|
#if ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
void pe_magnet_init() {
|
float parkingposx[2] , // M951 R L
|
||||||
for (uint8_t n = 0; n <= 1; ++n)
|
parkinggrabdistance , // M951 I
|
||||||
#if ENABLED(PARKING_EXTRUDER_SOLENOIDS_INVERT)
|
parkingslowspeed, // M951 J
|
||||||
pe_activate_magnet(n);
|
parkinghighspeed , // M951 H
|
||||||
|
parkingtraveldistance, // M951 D
|
||||||
|
compensationmultiplier;
|
||||||
|
|
||||||
|
inline void magnetic_parking_extruder_tool_change(const uint8_t tmp_extruder) {
|
||||||
|
|
||||||
|
const float oldx = current_position[X_AXIS],
|
||||||
|
grabpos = mpe_settings.parking_xpos[tmp_extruder] + (tmp_extruder ? mpe_settings.grab_distance : -mpe_settings.grab_distance),
|
||||||
|
offsetcompensation =
|
||||||
|
#if HAS_HOTEND_OFFSET
|
||||||
|
hotend_offset[X_AXIS][active_extruder] * mpe_settings.compensation_factor
|
||||||
#else
|
#else
|
||||||
pe_deactivate_magnet(n);
|
0
|
||||||
|
#endif
|
||||||
|
;
|
||||||
|
|
||||||
|
if (axis_unhomed_error(true, false, false)) return;
|
||||||
|
|
||||||
|
/**
|
||||||
|
* Z Lift and Nozzle Offset shift ar defined in caller method to work equal with any Multi Hotend realization
|
||||||
|
*
|
||||||
|
* Steps:
|
||||||
|
* 1. Move high speed to park position of new extruder
|
||||||
|
* 2. Move to couple position of new extruder (this also discouple the old extruder)
|
||||||
|
* 3. Move to park position of new extruder
|
||||||
|
* 4. Move high speed to approach park position of old extruder
|
||||||
|
* 5. Move to park position of old extruder
|
||||||
|
* 6. Move to starting position
|
||||||
|
*/
|
||||||
|
|
||||||
|
// STEP 1
|
||||||
|
|
||||||
|
current_position[X_AXIS] = mpe_settings.parking_xpos[tmp_extruder] + offsetcompensation;
|
||||||
|
|
||||||
|
#if ENABLED(DEBUG_LEVELING_FEATURE)
|
||||||
|
if (DEBUGGING(LEVELING)) {
|
||||||
|
SERIAL_ECHOPAIR("(1) Move extruder ", int(tmp_extruder));
|
||||||
|
DEBUG_POS(" to new extruder ParkPos", current_position);
|
||||||
|
}
|
||||||
|
#endif
|
||||||
|
|
||||||
|
planner.buffer_line(current_position, mpe_settings.fast_feedrate, tmp_extruder);
|
||||||
|
planner.synchronize();
|
||||||
|
|
||||||
|
// STEP 2
|
||||||
|
|
||||||
|
current_position[X_AXIS] = grabpos + offsetcompensation;
|
||||||
|
|
||||||
|
#if ENABLED(DEBUG_LEVELING_FEATURE)
|
||||||
|
if (DEBUGGING(LEVELING)) {
|
||||||
|
SERIAL_ECHOPAIR("(2) Couple extruder ", int(tmp_extruder));
|
||||||
|
DEBUG_POS(" to new extruder GrabPos", current_position);
|
||||||
|
}
|
||||||
|
#endif
|
||||||
|
|
||||||
|
planner.buffer_line(current_position, mpe_settings.slow_feedrate, tmp_extruder);
|
||||||
|
planner.synchronize();
|
||||||
|
|
||||||
|
// Delay before moving tool, to allow magnetic coupling
|
||||||
|
gcode.dwell(150);
|
||||||
|
|
||||||
|
// STEP 3
|
||||||
|
|
||||||
|
current_position[X_AXIS] = mpe_settings.parking_xpos[tmp_extruder] + offsetcompensation;
|
||||||
|
#if ENABLED(DEBUG_LEVELING_FEATURE)
|
||||||
|
if (DEBUGGING(LEVELING)) {
|
||||||
|
SERIAL_ECHOPAIR("(3) Move extruder ", int(tmp_extruder));
|
||||||
|
DEBUG_POS(" back to new extruder ParkPos", current_position);
|
||||||
|
}
|
||||||
|
#endif
|
||||||
|
|
||||||
|
planner.buffer_line(current_position, mpe_settings.slow_feedrate, tmp_extruder);
|
||||||
|
planner.synchronize();
|
||||||
|
|
||||||
|
// STEP 4
|
||||||
|
|
||||||
|
current_position[X_AXIS] = mpe_settings.parking_xpos[active_extruder] + (active_extruder == 0 ? MPE_TRAVEL_DISTANCE : -MPE_TRAVEL_DISTANCE) + offsetcompensation;
|
||||||
|
#if ENABLED(DEBUG_LEVELING_FEATURE)
|
||||||
|
if (DEBUGGING(LEVELING)) {
|
||||||
|
SERIAL_ECHOPAIR("(4) Move extruder ", int(tmp_extruder));
|
||||||
|
DEBUG_POS(" close to old extruder ParkPos", current_position);
|
||||||
|
}
|
||||||
|
#endif
|
||||||
|
|
||||||
|
planner.buffer_line(current_position, mpe_settings.fast_feedrate, tmp_extruder);
|
||||||
|
planner.synchronize();
|
||||||
|
|
||||||
|
// STEP 5
|
||||||
|
|
||||||
|
current_position[X_AXIS] = mpe_settings.parking_xpos[active_extruder] + offsetcompensation;
|
||||||
|
|
||||||
|
#if ENABLED(DEBUG_LEVELING_FEATURE)
|
||||||
|
if (DEBUGGING(LEVELING)) {
|
||||||
|
SERIAL_ECHOPAIR("(5) Park extruder ", int(tmp_extruder));
|
||||||
|
DEBUG_POS(" at old extruder ParkPos", current_position);
|
||||||
|
}
|
||||||
|
#endif
|
||||||
|
|
||||||
|
planner.buffer_line(current_position, mpe_settings.slow_feedrate, tmp_extruder);
|
||||||
|
planner.synchronize();
|
||||||
|
|
||||||
|
// STEP 6
|
||||||
|
|
||||||
|
current_position[X_AXIS] = oldx;
|
||||||
|
|
||||||
|
#if ENABLED(DEBUG_LEVELING_FEATURE)
|
||||||
|
if (DEBUGGING(LEVELING)) {
|
||||||
|
SERIAL_ECHOPAIR("(6) Move extruder ", int(tmp_extruder));
|
||||||
|
DEBUG_POS(" to starting position", current_position);
|
||||||
|
}
|
||||||
|
#endif
|
||||||
|
|
||||||
|
planner.buffer_line(current_position, mpe_settings.fast_feedrate, tmp_extruder);
|
||||||
|
planner.synchronize();
|
||||||
|
|
||||||
|
#if ENABLED(DEBUG_LEVELING_FEATURE)
|
||||||
|
if (DEBUGGING(LEVELING)) SERIAL_ECHOLNPGM("Autopark done.");
|
||||||
#endif
|
#endif
|
||||||
}
|
}
|
||||||
|
|
||||||
void pe_set_magnet(const uint8_t extruder_num, const uint8_t state) {
|
#elif ENABLED(PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
void pe_solenoid_init() {
|
||||||
|
for (uint8_t n = 0; n <= 1; ++n)
|
||||||
|
#if ENABLED(PARKING_EXTRUDER_SOLENOIDS_INVERT)
|
||||||
|
pe_activate_solenoid(n);
|
||||||
|
#else
|
||||||
|
pe_deactivate_solenoid(n);
|
||||||
|
#endif
|
||||||
|
}
|
||||||
|
|
||||||
|
void pe_set_solenoid(const uint8_t extruder_num, const uint8_t state) {
|
||||||
switch (extruder_num) {
|
switch (extruder_num) {
|
||||||
case 1: OUT_WRITE(SOL1_PIN, state); break;
|
case 1: OUT_WRITE(SOL1_PIN, state); break;
|
||||||
default: OUT_WRITE(SOL0_PIN, state); break;
|
default: OUT_WRITE(SOL0_PIN, state); break;
|
||||||
|
@ -206,7 +331,7 @@
|
||||||
if (DEBUGGING(LEVELING)) SERIAL_ECHOLNPGM("(3) Disengage magnet ");
|
if (DEBUGGING(LEVELING)) SERIAL_ECHOLNPGM("(3) Disengage magnet ");
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
pe_deactivate_magnet(active_extruder);
|
pe_deactivate_solenoid(active_extruder);
|
||||||
|
|
||||||
// STEP 4
|
// STEP 4
|
||||||
|
|
||||||
|
@ -229,10 +354,10 @@
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
#if ENABLED(PARKING_EXTRUDER_SOLENOIDS_INVERT)
|
#if ENABLED(PARKING_EXTRUDER_SOLENOIDS_INVERT)
|
||||||
pe_activate_magnet(active_extruder); //just save power for inverted magnets
|
pe_activate_solenoid(active_extruder); //just save power for inverted magnets
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
pe_activate_magnet(tmp_extruder);
|
pe_activate_solenoid(tmp_extruder);
|
||||||
|
|
||||||
// STEP 6
|
// STEP 6
|
||||||
|
|
||||||
|
@ -266,9 +391,9 @@
|
||||||
}
|
}
|
||||||
else { // nomove == true
|
else { // nomove == true
|
||||||
// Only engage magnetic field for new extruder
|
// Only engage magnetic field for new extruder
|
||||||
pe_activate_magnet(tmp_extruder);
|
pe_activate_solenoid(tmp_extruder);
|
||||||
#if ENABLED(PARKING_EXTRUDER_SOLENOIDS_INVERT)
|
#if ENABLED(PARKING_EXTRUDER_SOLENOIDS_INVERT)
|
||||||
pe_activate_magnet(active_extruder); // Just save power for inverted magnets
|
pe_activate_solenoid(active_extruder); // Just save power for inverted magnets
|
||||||
#endif
|
#endif
|
||||||
}
|
}
|
||||||
|
|
||||||
|
@ -661,6 +786,8 @@ void tool_change(const uint8_t tmp_extruder, const float fr_mm_s/*=0.0*/, bool n
|
||||||
dualx_tool_change(tmp_extruder, no_move);
|
dualx_tool_change(tmp_extruder, no_move);
|
||||||
#elif ENABLED(PARKING_EXTRUDER) // Dual Parking extruder
|
#elif ENABLED(PARKING_EXTRUDER) // Dual Parking extruder
|
||||||
parking_extruder_tool_change(tmp_extruder, no_move);
|
parking_extruder_tool_change(tmp_extruder, no_move);
|
||||||
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER) // Magnetic Parking extruder
|
||||||
|
magnetic_parking_extruder_tool_change(tmp_extruder);
|
||||||
#elif ENABLED(SWITCHING_TOOLHEAD) // Switching Toolhead
|
#elif ENABLED(SWITCHING_TOOLHEAD) // Switching Toolhead
|
||||||
switching_toolhead_tool_change(tmp_extruder, fr_mm_s, no_move);
|
switching_toolhead_tool_change(tmp_extruder, fr_mm_s, no_move);
|
||||||
#elif ENABLED(SWITCHING_NOZZLE) && !SWITCHING_NOZZLE_TWO_SERVOS
|
#elif ENABLED(SWITCHING_NOZZLE) && !SWITCHING_NOZZLE_TWO_SERVOS
|
||||||
|
|
|
@ -61,14 +61,29 @@
|
||||||
#define PE_MAGNET_ON_STATE PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE
|
#define PE_MAGNET_ON_STATE PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
void pe_set_magnet(const uint8_t extruder_num, const uint8_t state);
|
void pe_set_solenoid(const uint8_t extruder_num, const uint8_t state);
|
||||||
|
|
||||||
inline void pe_activate_magnet(const uint8_t extruder_num) { pe_set_magnet(extruder_num, PE_MAGNET_ON_STATE); }
|
inline void pe_activate_solenoid(const uint8_t extruder_num) { pe_set_solenoid(extruder_num, PE_MAGNET_ON_STATE); }
|
||||||
inline void pe_deactivate_magnet(const uint8_t extruder_num) { pe_set_magnet(extruder_num, !PE_MAGNET_ON_STATE); }
|
inline void pe_deactivate_solenoid(const uint8_t extruder_num) { pe_set_solenoid(extruder_num, !PE_MAGNET_ON_STATE); }
|
||||||
|
|
||||||
void pe_magnet_init();
|
void pe_solenoid_init();
|
||||||
|
|
||||||
#endif // PARKING_EXTRUDER
|
#elif ENABLED(MAGNETIC_PARKING_EXTRUDER)
|
||||||
|
|
||||||
|
typedef struct MPESettings {
|
||||||
|
float parking_xpos[2], // M951 L R
|
||||||
|
grab_distance, // M951 I
|
||||||
|
slow_feedrate, // M951 J
|
||||||
|
fast_feedrate, // M951 H
|
||||||
|
travel_distance, // M951 D
|
||||||
|
compensation_factor; // M951 C
|
||||||
|
} mpe_settings_t;
|
||||||
|
|
||||||
|
extern mpe_settings_t mpe_settings;
|
||||||
|
|
||||||
|
void mpe_settings_init();
|
||||||
|
|
||||||
|
#endif
|
||||||
|
|
||||||
#if ENABLED(SINGLENOZZLE)
|
#if ENABLED(SINGLENOZZLE)
|
||||||
extern uint16_t singlenozzle_temp[EXTRUDERS];
|
extern uint16_t singlenozzle_temp[EXTRUDERS];
|
||||||
|
|
|
@ -53,11 +53,13 @@ exec_test $1 $2 "Sled Z Probe with Linear leveling"
|
||||||
# exec_test $1 $2 "...with AUTO_BED_LEVELING_3POINT, DEBUG_LEVELING_FEATURE, EEPROM_SETTINGS, EEPROM_CHITCHAT, EXTENDED_CAPABILITIES_REPORT, and AUTO_REPORT_TEMPERATURES"
|
# exec_test $1 $2 "...with AUTO_BED_LEVELING_3POINT, DEBUG_LEVELING_FEATURE, EEPROM_SETTINGS, EEPROM_CHITCHAT, EXTENDED_CAPABILITIES_REPORT, and AUTO_REPORT_TEMPERATURES"
|
||||||
|
|
||||||
#
|
#
|
||||||
# Test MESH_BED_LEVELING feature, with LCD
|
# Test MAGNETIC_PARKING_EXTRUDER with LCD
|
||||||
#
|
#
|
||||||
restore_configs
|
restore_configs
|
||||||
opt_enable MESH_BED_LEVELING MESH_G28_REST_ORIGIN MANUAL_BED_LEVELING ULTIMAKERCONTROLLER
|
opt_set EXTRUDERS 2
|
||||||
exec_test $1 $2 "MESH_BED_LEVELING feature, with LCD"
|
opt_set TEMP_SENSOR_1 1
|
||||||
|
opt_enable MAGNETIC_PARKING_EXTRUDER ULTIMAKERCONTROLLER
|
||||||
|
exec_test $1 $2 "MAGNETIC_PARKING_EXTRUDER with LCD"
|
||||||
|
|
||||||
#
|
#
|
||||||
# Mixing Extruder
|
# Mixing Extruder
|
||||||
|
|
Loading…
Reference in a new issue