diff --git a/Marlin/Conditionals_post.h b/Marlin/Conditionals_post.h
index 0a5e1820c6..3edc8dfe83 100644
--- a/Marlin/Conditionals_post.h
+++ b/Marlin/Conditionals_post.h
@@ -649,7 +649,7 @@
   /**
    * Heater & Fan Pausing
    */
-  #if ENABLED(PROBING_FANS_OFF) && FAN_COUNT == 0
+  #if FAN_COUNT == 0
     #undef PROBING_FANS_OFF
   #endif
   #define QUIET_PROBING (ENABLED(PROBING_HEATERS_OFF) || ENABLED(PROBING_FANS_OFF))
diff --git a/Marlin/Marlin_main.cpp b/Marlin/Marlin_main.cpp
index 45bfac5c0f..2d685e3117 100644
--- a/Marlin/Marlin_main.cpp
+++ b/Marlin/Marlin_main.cpp
@@ -2057,24 +2057,21 @@ static void clean_up_after_endstop_or_probe_move() {
 #endif
 
 #if ENABLED(PROBING_FANS_OFF)
-  void fans_pause(bool p) {
-    if (p == fans_paused) { // If called out of order something is wrong
-      SERIAL_ERROR_START;
-      serialprintPGM(fans_paused ? PSTR("Fans already paused!") : PSTR("Fans already unpaused!"));
-      return;
+
+  void fans_pause(const bool p) {
+    if (p != fans_paused) {
+      fans_paused = p;
+      if (p)
+        for (uint8_t x = 0; x < FAN_COUNT; x++) {
+          paused_fanSpeeds[x] = fanSpeeds[x];
+          fanSpeeds[x] = 0;
+        }
+      else
+        for (uint8_t x = 0; x < FAN_COUNT; x++)
+          fanSpeeds[x] = paused_fanSpeeds[x];
     }
-
-    if (p)
-      for (uint8_t x = 0;x < FAN_COUNT;x++) {
-        paused_fanSpeeds[x] = fanSpeeds[x];
-        fanSpeeds[x] = 0;
-      }
-    else
-      for (uint8_t x = 0;x < FAN_COUNT;x++)
-        fanSpeeds[x] = paused_fanSpeeds[x];
-
-    fans_paused = p;
   }
+
 #endif // PROBING_FANS_OFF
 
 #if HAS_BED_PROBE
@@ -2089,18 +2086,16 @@ static void clean_up_after_endstop_or_probe_move() {
   #endif
 
   #if QUIET_PROBING
-    void probing_pause(bool pause) {
+    void probing_pause(const bool p) {
       #if ENABLED(PROBING_HEATERS_OFF)
-        thermalManager.pause(pause);
+        thermalManager.pause(p);
       #endif
-
       #if ENABLED(PROBING_FANS_OFF)
-        fans_pause(pause);
+        fans_pause(p);
       #endif
-
-      if(pause) safe_delay(25);
+      if (p) safe_delay(25);
     }
-  #endif
+  #endif // QUIET_PROBING
 
   #if ENABLED(BLTOUCH)
 
@@ -11141,7 +11136,7 @@ void set_current_from_steppers_for_axis(const AxisEnum axis) {
     // SERIAL_ECHOPAIR(" seconds=", seconds);
     // SERIAL_ECHOLNPAIR(" segments=", segments);
 
-    #if IS_SCARA
+    #if IS_SCARA && ENABLED(SCARA_FEEDRATE_SCALING)
       // SCARA needs to scale the feed rate from mm/s to degrees/s
       const float inv_segment_length = min(10.0, float(segments) / cartesian_mm), // 1/mm/segs
                   feed_factor = inv_segment_length * _feedrate_mm_s;
@@ -11168,7 +11163,7 @@ void set_current_from_steppers_for_axis(const AxisEnum axis) {
 
       ADJUST_DELTA(logical); // Adjust Z if bed leveling is enabled
 
-      #if IS_SCARA
+      #if IS_SCARA && ENABLED(SCARA_FEEDRATE_SCALING)
         // For SCARA scale the feed rate from mm/s to degrees/s
         // Use ratio between the length of the move and the larger angle change
         const float adiff = abs(delta[A_AXIS] - oldA),
@@ -11184,7 +11179,7 @@ void set_current_from_steppers_for_axis(const AxisEnum axis) {
     // Since segment_distance is only approximate,
     // the final move must be to the exact destination.
 
-    #if IS_SCARA
+    #if IS_SCARA && ENABLED(SCARA_FEEDRATE_SCALING)
       // For SCARA scale the feed rate from mm/s to degrees/s
       // With segments > 1 length is 1 segment, otherwise total length
       inverse_kinematics(ltarget);
@@ -11516,7 +11511,7 @@ void prepare_move_to_destination() {
     const millis_t ms = millis();
     if (ELAPSED(ms, nextMotorCheck)) {
       nextMotorCheck = ms + 2500UL; // Not a time critical function, so only check every 2.5s
-      if (X_ENABLE_READ == X_ENABLE_ON || Y_ENABLE_READ == Y_ENABLE_ON || Z_ENABLE_READ == Z_ENABLE_ON || thermalManager.soft_pwm_bed > 0
+      if (X_ENABLE_READ == X_ENABLE_ON || Y_ENABLE_READ == Y_ENABLE_ON || Z_ENABLE_READ == Z_ENABLE_ON || thermalManager.soft_pwm_amount_bed > 0
           || E0_ENABLE_READ == E_ENABLE_ON // If any of the drivers are enabled...
           #if E_STEPPERS > 1
             || E1_ENABLE_READ == E_ENABLE_ON
diff --git a/Marlin/example_configurations/SCARA/Configuration.h b/Marlin/example_configurations/SCARA/Configuration.h
index fcaf75b4e7..d464efd3ca 100644
--- a/Marlin/example_configurations/SCARA/Configuration.h
+++ b/Marlin/example_configurations/SCARA/Configuration.h
@@ -76,6 +76,7 @@
 
 #if ENABLED(MORGAN_SCARA) || ENABLED(MAKERARM_SCARA)
   //#define DEBUG_SCARA_KINEMATICS
+  //#define SCARA_FEEDRATE_SCALING // Convert XY feedrate from mm/s to degrees/s on the fly
 
   // If movement is choppy try lowering this value
   #define SCARA_SEGMENTS_PER_SECOND 200
diff --git a/Marlin/planner.cpp b/Marlin/planner.cpp
index 2a0bfe2a70..f95d8ab6ef 100644
--- a/Marlin/planner.cpp
+++ b/Marlin/planner.cpp
@@ -491,13 +491,13 @@ void Planner::check_axes_activity() {
 
     #if ENABLED(FAN_SOFT_PWM)
       #if HAS_FAN0
-        thermalManager.fanSpeedSoftPwm[0] = CALC_FAN_SPEED(0);
+        thermalManager.soft_pwm_amount_fan[0] = CALC_FAN_SPEED(0);
       #endif
       #if HAS_FAN1
-        thermalManager.fanSpeedSoftPwm[1] = CALC_FAN_SPEED(1);
+        thermalManager.soft_pwm_amount_fan[1] = CALC_FAN_SPEED(1);
       #endif
       #if HAS_FAN2
-        thermalManager.fanSpeedSoftPwm[2] = CALC_FAN_SPEED(2);
+        thermalManager.soft_pwm_amount_fan[2] = CALC_FAN_SPEED(2);
       #endif
     #else
       #if HAS_FAN0
diff --git a/platformio.ini b/Marlin/platformio.ini
similarity index 100%
rename from platformio.ini
rename to Marlin/platformio.ini
diff --git a/Marlin/temperature.cpp b/Marlin/temperature.cpp
index 3b9454ccc4..6021d899ad 100644
--- a/Marlin/temperature.cpp
+++ b/Marlin/temperature.cpp
@@ -74,12 +74,6 @@ int16_t Temperature::current_temperature_raw[HOTENDS] = { 0 },
   float Temperature::redundant_temperature = 0.0;
 #endif
 
-uint8_t Temperature::soft_pwm_bed;
-
-#if ENABLED(FAN_SOFT_PWM)
-  uint8_t Temperature::fanSpeedSoftPwm[FAN_COUNT];
-#endif
-
 #if ENABLED(PIDTEMP)
   #if ENABLED(PID_PARAMS_PER_HOTEND) && HOTENDS > 1
     float Temperature::Kp[HOTENDS] = ARRAY_BY_HOTENDS1(DEFAULT_Kp),
@@ -194,10 +188,12 @@ int16_t Temperature::minttemp_raw[HOTENDS] = ARRAY_BY_HOTENDS(HEATER_0_RAW_LO_TE
   millis_t Temperature::next_auto_fan_check_ms = 0;
 #endif
 
-uint8_t Temperature::soft_pwm[HOTENDS];
+uint8_t Temperature::soft_pwm_amount[HOTENDS],
+        Temperature::soft_pwm_amount_bed;
 
 #if ENABLED(FAN_SOFT_PWM)
-  uint8_t Temperature::soft_pwm_fan[FAN_COUNT];
+  uint8_t Temperature::soft_pwm_amount_fan[FAN_COUNT],
+          Temperature::soft_pwm_count_fan[FAN_COUNT];
 #endif
 
 #if ENABLED(FILAMENT_WIDTH_SENSOR)
@@ -206,7 +202,7 @@ uint8_t Temperature::soft_pwm[HOTENDS];
 
 #if ENABLED(PROBING_HEATERS_OFF)
   bool Temperature::paused;
-  int16_t Temperature::paused_hotend_temps[HOTENDS];
+  int16_t Temperature::paused_hotend_temp[HOTENDS];
   #if HAS_TEMP_BED
     int16_t Temperature::paused_bed_temp;
   #endif
@@ -254,13 +250,13 @@ uint8_t Temperature::soft_pwm[HOTENDS];
 
     #if HAS_PID_FOR_BOTH
       if (hotend < 0)
-        soft_pwm_bed = bias = d = (MAX_BED_POWER) >> 1;
+        soft_pwm_amount_bed = bias = d = (MAX_BED_POWER) >> 1;
       else
-        soft_pwm[hotend] = bias = d = (PID_MAX) >> 1;
+        soft_pwm_amount[hotend] = bias = d = (PID_MAX) >> 1;
     #elif ENABLED(PIDTEMP)
-      soft_pwm[hotend] = bias = d = (PID_MAX) >> 1;
+      soft_pwm_amount[hotend] = bias = d = (PID_MAX) >> 1;
     #else
-      soft_pwm_bed = bias = d = (MAX_BED_POWER) >> 1;
+      soft_pwm_amount_bed = bias = d = (MAX_BED_POWER) >> 1;
     #endif
 
     wait_for_heatup = true;
@@ -298,13 +294,13 @@ uint8_t Temperature::soft_pwm[HOTENDS];
             heating = false;
             #if HAS_PID_FOR_BOTH
               if (hotend < 0)
-                soft_pwm_bed = (bias - d) >> 1;
+                soft_pwm_amount_bed = (bias - d) >> 1;
               else
-                soft_pwm[hotend] = (bias - d) >> 1;
+                soft_pwm_amount[hotend] = (bias - d) >> 1;
             #elif ENABLED(PIDTEMP)
-              soft_pwm[hotend] = (bias - d) >> 1;
+              soft_pwm_amount[hotend] = (bias - d) >> 1;
             #elif ENABLED(PIDTEMPBED)
-              soft_pwm_bed = (bias - d) >> 1;
+              soft_pwm_amount_bed = (bias - d) >> 1;
             #endif
             t1 = ms;
             t_high = t1 - t2;
@@ -367,13 +363,13 @@ uint8_t Temperature::soft_pwm[HOTENDS];
             }
             #if HAS_PID_FOR_BOTH
               if (hotend < 0)
-                soft_pwm_bed = (bias + d) >> 1;
+                soft_pwm_amount_bed = (bias + d) >> 1;
               else
-                soft_pwm[hotend] = (bias + d) >> 1;
+                soft_pwm_amount[hotend] = (bias + d) >> 1;
             #elif ENABLED(PIDTEMP)
-              soft_pwm[hotend] = (bias + d) >> 1;
+              soft_pwm_amount[hotend] = (bias + d) >> 1;
             #else
-              soft_pwm_bed = (bias + d) >> 1;
+              soft_pwm_amount_bed = (bias + d) >> 1;
             #endif
             cycles++;
             min = temp;
@@ -466,7 +462,7 @@ void Temperature::updatePID() {
 }
 
 int Temperature::getHeaterPower(int heater) {
-  return heater < 0 ? soft_pwm_bed : soft_pwm[heater];
+  return heater < 0 ? soft_pwm_amount_bed : soft_pwm_amount[heater];
 }
 
 #if HAS_AUTO_FAN
@@ -717,7 +713,7 @@ void Temperature::manage_heater() {
     float pid_output = get_pid_output(e);
 
     // Check if temperature is within the correct range
-    soft_pwm[e] = (current_temperature[e] > minttemp[e] || is_preheating(e)) && current_temperature[e] < maxttemp[e] ? (int)pid_output >> 1 : 0;
+    soft_pwm_amount[e] = (current_temperature[e] > minttemp[e] || is_preheating(e)) && current_temperature[e] < maxttemp[e] ? (int)pid_output >> 1 : 0;
 
     // Check if the temperature is failing to increase
     #if WATCH_HOTENDS
@@ -798,27 +794,27 @@ void Temperature::manage_heater() {
     #if ENABLED(PIDTEMPBED)
       float pid_output = get_pid_output_bed();
 
-      soft_pwm_bed = WITHIN(current_temperature_bed, BED_MINTEMP, BED_MAXTEMP) ? (int)pid_output >> 1 : 0;
+      soft_pwm_amount_bed = WITHIN(current_temperature_bed, BED_MINTEMP, BED_MAXTEMP) ? (int)pid_output >> 1 : 0;
 
     #elif ENABLED(BED_LIMIT_SWITCHING)
       // Check if temperature is within the correct band
       if (WITHIN(current_temperature_bed, BED_MINTEMP, BED_MAXTEMP)) {
         if (current_temperature_bed >= target_temperature_bed + BED_HYSTERESIS)
-          soft_pwm_bed = 0;
+          soft_pwm_amount_bed = 0;
         else if (current_temperature_bed <= target_temperature_bed - (BED_HYSTERESIS))
-          soft_pwm_bed = MAX_BED_POWER >> 1;
+          soft_pwm_amount_bed = MAX_BED_POWER >> 1;
       }
       else {
-        soft_pwm_bed = 0;
+        soft_pwm_amount_bed = 0;
         WRITE_HEATER_BED(LOW);
       }
     #else // !PIDTEMPBED && !BED_LIMIT_SWITCHING
       // Check if temperature is within the correct range
       if (WITHIN(current_temperature_bed, BED_MINTEMP, BED_MAXTEMP)) {
-        soft_pwm_bed = current_temperature_bed < target_temperature_bed ? MAX_BED_POWER >> 1 : 0;
+        soft_pwm_amount_bed = current_temperature_bed < target_temperature_bed ? MAX_BED_POWER >> 1 : 0;
       }
       else {
-        soft_pwm_bed = 0;
+        soft_pwm_amount_bed = 0;
         WRITE_HEATER_BED(LOW);
       }
     #endif
@@ -1205,7 +1201,7 @@ void Temperature::init() {
 
   #if ENABLED(PROBING_HEATERS_OFF)
     paused = false;
-    ZERO(paused_hotend_temps);
+    ZERO(paused_hotend_temp);
     #if HAS_TEMP_BED
       paused_bed_temp = 0;
     #endif
@@ -1316,7 +1312,7 @@ void Temperature::disable_all_heaters() {
   // Unpause and reset everything
   #if ENABLED(PROBING_HEATERS_OFF)
     paused = false;
-    ZERO(paused_hotend_temps);
+    ZERO(paused_hotend_temp);
     #if HAS_TEMP_BED
       paused_bed_temp = 0;
     #endif
@@ -1327,7 +1323,7 @@ void Temperature::disable_all_heaters() {
 
   #define DISABLE_HEATER(NR) { \
     setTargetHotend(0, NR); \
-    soft_pwm[NR] = 0; \
+    soft_pwm_amount[NR] = 0; \
     WRITE_HEATER_ ##NR (LOW); \
   }
 
@@ -1349,7 +1345,7 @@ void Temperature::disable_all_heaters() {
 
   #if HAS_TEMP_BED
     target_temperature_bed = 0;
-    soft_pwm_bed = 0;
+    soft_pwm_amount_bed = 0;
     #if HAS_HEATER_BED
       WRITE_HEATER_BED(LOW);
     #endif
@@ -1357,36 +1353,29 @@ void Temperature::disable_all_heaters() {
 }
 
 #if ENABLED(PROBING_HEATERS_OFF)
-  void Temperature::pause(bool p) {
-    if (p == paused) { // If called out of order something is wrong
-      SERIAL_ERROR_START;
-      serialprintPGM(paused ? PSTR("Heaters already paused!") : PSTR("Heaters already unpaused!"));
-      return;
-    }
 
-    if (p) {
-      HOTEND_LOOP() {
-        paused_hotend_temps[e] = degTargetHotend(e);
-        setTargetHotend(0, e);
+  void Temperature::pause(const bool p) {
+    if (p != paused) {
+      paused = p;
+      if (p) {
+        HOTEND_LOOP() {
+          paused_hotend_temp[e] = degTargetHotend(e);
+          setTargetHotend(0, e);
+        }
+        #if HAS_TEMP_BED
+          paused_bed_temp = degTargetBed();
+          setTargetBed(0);
+        #endif
+      }
+      else {
+        HOTEND_LOOP() setTargetHotend(paused_hotend_temp[e], e);
+        #if HAS_TEMP_BED
+          setTargetBed(paused_bed_temp);
+        #endif
       }
-      #if HAS_TEMP_BED
-        paused_bed_temp = degTargetBed();
-        setTargetBed(0);
-      #endif
     }
-    else {
-      HOTEND_LOOP() setTargetHotend(paused_hotend_temps[e], e);
-      #if HAS_TEMP_BED
-        setTargetBed(paused_bed_temp);
-      #endif
-    }
-
-    paused = p;
   }
 
-  bool Temperature::ispaused() {
-    return paused;
-  }
 #endif // PROBING_HEATERS_OFF
 
 #if ENABLED(HEATER_0_USES_MAX6675)
@@ -1613,11 +1602,11 @@ void Temperature::isr() {
   #if ENABLED(SLOW_PWM_HEATERS)
     static uint8_t slow_pwm_count = 0;
     #define ISR_STATICS(n) \
-      static uint8_t soft_pwm_ ## n; \
-      static uint8_t state_heater_ ## n = 0; \
-      static uint8_t state_timer_heater_ ## n = 0
+      static uint8_t soft_pwm_count_ ## n, \
+                     state_heater_ ## n = 0, \
+                     state_timer_heater_ ## n = 0
   #else
-    #define ISR_STATICS(n) static uint8_t soft_pwm_ ## n = 0
+    #define ISR_STATICS(n) static uint8_t soft_pwm_count_ ## n = 0
   #endif
 
   // Statics per heater
@@ -1656,73 +1645,73 @@ void Temperature::isr() {
      */
     if (pwm_count_tmp >= 127) {
       pwm_count_tmp -= 127;
-      soft_pwm_0 = (soft_pwm_0 & pwm_mask) + soft_pwm[0];
-      WRITE_HEATER_0(soft_pwm_0 > pwm_mask ? HIGH : LOW);
+      soft_pwm_count_0 = (soft_pwm_count_0 & pwm_mask) + soft_pwm_amount[0];
+      WRITE_HEATER_0(soft_pwm_count_0 > pwm_mask ? HIGH : LOW);
       #if HOTENDS > 1
-        soft_pwm_1 = (soft_pwm_1 & pwm_mask) + soft_pwm[1];
-        WRITE_HEATER_1(soft_pwm_1 > pwm_mask ? HIGH : LOW);
+        soft_pwm_count_1 = (soft_pwm_count_1 & pwm_mask) + soft_pwm_amount[1];
+        WRITE_HEATER_1(soft_pwm_count_1 > pwm_mask ? HIGH : LOW);
         #if HOTENDS > 2
-          soft_pwm_2 = (soft_pwm_2 & pwm_mask) + soft_pwm[2];
-          WRITE_HEATER_2(soft_pwm_2 > pwm_mask ? HIGH : LOW);
+          soft_pwm_count_2 = (soft_pwm_count_2 & pwm_mask) + soft_pwm_amount[2];
+          WRITE_HEATER_2(soft_pwm_count_2 > pwm_mask ? HIGH : LOW);
           #if HOTENDS > 3
-            soft_pwm_3 = (soft_pwm_3 & pwm_mask) + soft_pwm[3];
-            WRITE_HEATER_3(soft_pwm_3 > pwm_mask ? HIGH : LOW);
+            soft_pwm_count_3 = (soft_pwm_count_3 & pwm_mask) + soft_pwm_amount[3];
+            WRITE_HEATER_3(soft_pwm_count_3 > pwm_mask ? HIGH : LOW);
             #if HOTENDS > 4
-              soft_pwm_4 = (soft_pwm_4 & pwm_mask) + soft_pwm[4];
-              WRITE_HEATER_4(soft_pwm_4 > pwm_mask ? HIGH : LOW);
+              soft_pwm_count_4 = (soft_pwm_count_4 & pwm_mask) + soft_pwm_amount[4];
+              WRITE_HEATER_4(soft_pwm_count_4 > pwm_mask ? HIGH : LOW);
             #endif // HOTENDS > 4
           #endif // HOTENDS > 3
         #endif // HOTENDS > 2
       #endif // HOTENDS > 1
 
       #if HAS_HEATER_BED
-        soft_pwm_BED = (soft_pwm_BED & pwm_mask) + soft_pwm_bed;
-        WRITE_HEATER_BED(soft_pwm_BED > pwm_mask ? HIGH : LOW);
+        soft_pwm_count_BED = (soft_pwm_count_BED & pwm_mask) + soft_pwm_amount_bed;
+        WRITE_HEATER_BED(soft_pwm_count_BED > pwm_mask ? HIGH : LOW);
       #endif
 
       #if ENABLED(FAN_SOFT_PWM)
         #if HAS_FAN0
-          soft_pwm_fan[0] = (soft_pwm_fan[0] & pwm_mask) + fanSpeedSoftPwm[0] >> 1;
-          WRITE_FAN(soft_pwm_fan[0] > pwm_mask ? HIGH : LOW);
+          soft_pwm_count_fan[0] = (soft_pwm_count_fan[0] & pwm_mask) + soft_pwm_amount_fan[0] >> 1;
+          WRITE_FAN(soft_pwm_count_fan[0] > pwm_mask ? HIGH : LOW);
         #endif
         #if HAS_FAN1
-          soft_pwm_fan[1] = (soft_pwm_fan[1] & pwm_mask) + fanSpeedSoftPwm[1] >> 1;
-          WRITE_FAN1(soft_pwm_fan[1] > pwm_mask ? HIGH : LOW);
+          soft_pwm_count_fan[1] = (soft_pwm_count_fan[1] & pwm_mask) + soft_pwm_amount_fan[1] >> 1;
+          WRITE_FAN1(soft_pwm_count_fan[1] > pwm_mask ? HIGH : LOW);
         #endif
         #if HAS_FAN2
-          soft_pwm_fan[2] = (soft_pwm_fan[2] & pwm_mask) + fanSpeedSoftPwm[2] >> 1;
-          WRITE_FAN2(soft_pwm_fan[2] > pwm_mask ? HIGH : LOW);
+          soft_pwm_count_fan[2] = (soft_pwm_count_fan[2] & pwm_mask) + soft_pwm_amount_fan[2] >> 1;
+          WRITE_FAN2(soft_pwm_count_fan[2] > pwm_mask ? HIGH : LOW);
         #endif
       #endif
     }
     else {
-      if (soft_pwm_0 <= pwm_count_tmp) WRITE_HEATER_0(0);
+      if (soft_pwm_count_0 <= pwm_count_tmp) WRITE_HEATER_0(0);
       #if HOTENDS > 1
-        if (soft_pwm_1 <= pwm_count_tmp) WRITE_HEATER_1(0);
+        if (soft_pwm_count_1 <= pwm_count_tmp) WRITE_HEATER_1(0);
         #if HOTENDS > 2
-          if (soft_pwm_2 <= pwm_count_tmp) WRITE_HEATER_2(0);
+          if (soft_pwm_count_2 <= pwm_count_tmp) WRITE_HEATER_2(0);
           #if HOTENDS > 3
-            if (soft_pwm_3 <= pwm_count_tmp) WRITE_HEATER_3(0);
+            if (soft_pwm_count_3 <= pwm_count_tmp) WRITE_HEATER_3(0);
             #if HOTENDS > 4
-              if (soft_pwm_4 <= pwm_count_tmp) WRITE_HEATER_4(0);
+              if (soft_pwm_count_4 <= pwm_count_tmp) WRITE_HEATER_4(0);
             #endif // HOTENDS > 4
           #endif // HOTENDS > 3
         #endif // HOTENDS > 2
       #endif // HOTENDS > 1
 
       #if HAS_HEATER_BED
-        if (soft_pwm_BED <= pwm_count_tmp) WRITE_HEATER_BED(0);
+        if (soft_pwm_count_BED <= pwm_count_tmp) WRITE_HEATER_BED(0);
       #endif
 
       #if ENABLED(FAN_SOFT_PWM)
         #if HAS_FAN0
-          if (soft_pwm_fan[0] <= pwm_count_tmp) WRITE_FAN(0);
+          if (soft_pwm_count_fan[0] <= pwm_count_tmp) WRITE_FAN(0);
         #endif
         #if HAS_FAN1
-          if (soft_pwm_fan[1] <= pwm_count_tmp) WRITE_FAN1(0);
+          if (soft_pwm_count_fan[1] <= pwm_count_tmp) WRITE_FAN1(0);
         #endif
         #if HAS_FAN2
-          if (soft_pwm_fan[2] <= pwm_count_tmp) WRITE_FAN2(0);
+          if (soft_pwm_count_fan[2] <= pwm_count_tmp) WRITE_FAN2(0);
         #endif
       #endif
     }
@@ -1765,7 +1754,7 @@ void Temperature::isr() {
           WRITE_HEATER_ ##NR(0); \
         } \
       }
-    #define SLOW_PWM_ROUTINE(n) _SLOW_PWM_ROUTINE(n, soft_pwm[n])
+    #define SLOW_PWM_ROUTINE(n) _SLOW_PWM_ROUTINE(n, soft_pwm_amount[n])
 
     #define PWM_OFF_ROUTINE(NR) \
       if (soft_pwm_ ##NR < slow_pwm_count) { \
@@ -1792,7 +1781,7 @@ void Temperature::isr() {
         #endif // HOTENDS > 2
       #endif // HOTENDS > 1
       #if HAS_HEATER_BED
-        _SLOW_PWM_ROUTINE(BED, soft_pwm_bed); // BED
+        _SLOW_PWM_ROUTINE(BED, soft_pwm_amount_bed); // BED
       #endif
 
     } // slow_pwm_count == 0
@@ -1818,26 +1807,26 @@ void Temperature::isr() {
       if (pwm_count_tmp >= 127) {
         pwm_count_tmp = 0;
         #if HAS_FAN0
-          soft_pwm_fan[0] = fanSpeedSoftPwm[0] >> 1;
-          WRITE_FAN(soft_pwm_fan[0] > 0 ? HIGH : LOW);
+          soft_pwm_count_fan[0] = soft_pwm_amount_fan[0] >> 1;
+          WRITE_FAN(soft_pwm_count_fan[0] > 0 ? HIGH : LOW);
         #endif
         #if HAS_FAN1
-          soft_pwm_fan[1] = fanSpeedSoftPwm[1] >> 1;
-          WRITE_FAN1(soft_pwm_fan[1] > 0 ? HIGH : LOW);
+          soft_pwm_count_fan[1] = soft_pwm_amount_fan[1] >> 1;
+          WRITE_FAN1(soft_pwm_count_fan[1] > 0 ? HIGH : LOW);
         #endif
         #if HAS_FAN2
-          soft_pwm_fan[2] = fanSpeedSoftPwm[2] >> 1;
-          WRITE_FAN2(soft_pwm_fan[2] > 0 ? HIGH : LOW);
+          soft_pwm_count_fan[2] = soft_pwm_amount_fan[2] >> 1;
+          WRITE_FAN2(soft_pwm_count_fan[2] > 0 ? HIGH : LOW);
         #endif
       }
       #if HAS_FAN0
-        if (soft_pwm_fan[0] <= pwm_count_tmp) WRITE_FAN(0);
+        if (soft_pwm_count_fan[0] <= pwm_count_tmp) WRITE_FAN(0);
       #endif
       #if HAS_FAN1
-        if (soft_pwm_fan[1] <= pwm_count_tmp) WRITE_FAN1(0);
+        if (soft_pwm_count_fan[1] <= pwm_count_tmp) WRITE_FAN1(0);
       #endif
       #if HAS_FAN2
-        if (soft_pwm_fan[2] <= pwm_count_tmp) WRITE_FAN2(0);
+        if (soft_pwm_count_fan[2] <= pwm_count_tmp) WRITE_FAN2(0);
       #endif
     #endif // FAN_SOFT_PWM
 
diff --git a/Marlin/temperature.h b/Marlin/temperature.h
index 7fc9926c35..e8632311d6 100644
--- a/Marlin/temperature.h
+++ b/Marlin/temperature.h
@@ -109,10 +109,12 @@ class Temperature {
       static float redundant_temperature;
     #endif
 
-    static uint8_t soft_pwm_bed;
+    static uint8_t soft_pwm_amount[HOTENDS],
+                   soft_pwm_amount_bed;
 
     #if ENABLED(FAN_SOFT_PWM)
-      static uint8_t fanSpeedSoftPwm[FAN_COUNT];
+      static uint8_t soft_pwm_amount_fan[FAN_COUNT],
+                     soft_pwm_count_fan[FAN_COUNT];
     #endif
 
     #if ENABLED(PIDTEMP) || ENABLED(PIDTEMPBED)
@@ -249,19 +251,13 @@ class Temperature {
       static millis_t next_auto_fan_check_ms;
     #endif
 
-    static uint8_t soft_pwm[HOTENDS];
-
-    #if ENABLED(FAN_SOFT_PWM)
-      static uint8_t soft_pwm_fan[FAN_COUNT];
-    #endif
-
     #if ENABLED(FILAMENT_WIDTH_SENSOR)
       static int current_raw_filwidth;  //Holds measured filament diameter - one extruder only
     #endif
 
     #if ENABLED(PROBING_HEATERS_OFF)
       static bool paused;
-      static int16_t paused_hotend_temps[HOTENDS];
+      static int16_t paused_hotend_temp[HOTENDS];
 
       #if HAS_TEMP_BED
         static int16_t paused_bed_temp;
@@ -462,8 +458,7 @@ class Temperature {
     #endif // BABYSTEPPING
 
     #if ENABLED(PROBING_HEATERS_OFF)
-      static void pause(bool p);
-      static bool ispaused();
+      static void pause(const bool p);
     #endif
 
   private:
diff --git a/Marlin/ubl_G29.cpp b/Marlin/ubl_G29.cpp
index 247ae27d65..7a174f702d 100644
--- a/Marlin/ubl_G29.cpp
+++ b/Marlin/ubl_G29.cpp
@@ -1006,7 +1006,7 @@
     if (!ubl.state.active) SERIAL_PROTOCOLPGM("de");
     SERIAL_PROTOCOLLNPGM("activated.\n");
   }
- 
+
   bool g29_parameter_parsing() {
     bool err_flag = false;
 
diff --git a/Marlin/ubl_motion.cpp b/Marlin/ubl_motion.cpp
index a6065dab55..5fbf141abd 100644
--- a/Marlin/ubl_motion.cpp
+++ b/Marlin/ubl_motion.cpp
@@ -225,7 +225,7 @@
     const float e_normalized_dist = e_position / on_axis_distance,
                 z_normalized_dist = z_position / on_axis_distance;
 
-    int current_xi = cell_start_xi, 
+    int current_xi = cell_start_xi,
         current_yi = cell_start_yi;
 
     const float m = dy / dx,
diff --git a/README.md b/README.md
index 393cb20bd3..730a0bdd62 100644
--- a/README.md
+++ b/README.md
@@ -113,37 +113,37 @@ Proposed patches should be submitted as a Pull Request against this branch ([bug
 ## Credits
 
 The current Marlin dev team consists of:
- - Roxanne Neufeld [@Roxy-3D] - English
- - Scott Lahteine [@thinkyhead] - English
- - Bob Kuhn [@Bob-the-Kuhn] - English
- - Andreas Hardtung [@AnHardt] - Deutsch, English
- - Nico Tonnhofer [@Wurstnase] - Deutsch, English
- - Jochen Groppe [@CONSULitAS] - Deutsch, English
- - João Brazio [@jbrazio] - Portuguese, English
- - Bo Hermannsen [@boelle] - Danish, English
- - Bob Cousins [@bobc] - English
- - [@maverikou]
- - Chris Palmer [@nophead]
- - [@paclema]
- - Erik van der Zalm [@ErikZalm]
- - David Braam [@daid]
- - Bernhard Kubicek [@bkubicek]
+ - Roxanne Neufeld [[@Roxy-3D](https://github.com/Roxy-3D)] - English
+ - Scott Lahteine [[@thinkyhead](https://github.com/thinkyhead)] - English
+ - Bob Kuhn [[@Bob-the-Kuhn](https://github.com/Bob-the-Kuhn)] - English
+ - Andreas Hardtung [[@AnHardt](https://github.com/AnHardt)] - Deutsch, English
+ - Nico Tonnhofer [[@Wurstnase](https://github.com/Wurstnase)] - Deutsch, English
+ - Jochen Groppe [[@CONSULitAS](https://github.com/CONSULitAS)] - Deutsch, English
+ - João Brazio [[@jbrazio](https://github.com/jbrazio)] - Portuguese, English
+ - Bo Hermannsen [[@boelle](https://github.com/boelle)] - Danish, English
+ - Bob Cousins [[@bobc](https://github.com/bobc)] - English
+ - [[@maverikou](https://github.com/maverikou)]
+ - Chris Palmer [[@nophead](https://github.com/nophead)]
+ - [[@paclema](https://github.com/paclema)]
+ - Erik van der Zalm [[@ErikZalm](https://github.com/ErikZalm)]
+ - David Braam [[@daid](https://github.com/daid)]
+ - Bernhard Kubicek [[@bkubicek](https://github.com/bkubicek)]
 
 More features have been added by:
- - Alberto Cotronei [@MagoKimbra] - English, Italian
- - Thomas Moore [@tcm0116]
- - Ernesto Martinez [@emartinez167]
- - Petr Zahradnik [@clexpert]
- - Kai [@Kaibob2]
- - Edward Patel [@epatel]
- - F. Malpartida [@fmalpartida] - English, Spanish
- - [@esenapaj] - English, Japanese
- - [@benlye]
- - [@Tannoo]
- - [@teemuatlut]
- - [@bgort]
- - [@LVD-AC]
- - [@paulusjacobus]
+ - Alberto Cotronei [[@MagoKimbra](https://github.com/MagoKimbra)] - English, Italian
+ - Thomas Moore [[@tcm0116](https://github.com/tcm0116)]
+ - Ernesto Martinez [[@emartinez167](https://github.com/emartinez167)]
+ - Petr Zahradnik [[@clexpert](https://github.com/clexpert)]
+ - Kai [[@Kaibob2](https://github.com/Kaibob2)]
+ - Edward Patel [[@epatel](https://github.com/epatel)]
+ - F. Malpartida [[@fmalpartida](https://github.com/fmalpartida)] - English, Spanish
+ - [[@esenapaj](https://github.com/esenapaj)] - English, Japanese
+ - [[@benlye](https://github.com/benlye)]
+ - [[@Tannoo](https://github.com/Tannoo)]
+ - [[@teemuatlut](https://github.com/teemuatlut)]
+ - [[@bgort](https://github.com/bgort)]
+ - [[@LVD-AC](https://github.com/LVD-AC)]
+ - [[@paulusjacobus](https://github.com/paulusjacobus)]
  - ...and many others
 
 ## License