zaubentrucker/muele-marlin
1
0
Fork 0
Code Issues Pull requests Actions Packages Projects Releases Wiki Activity

Support for Debug Codes - Dnnn (#19225)

Browse source 
Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>
This commit is contained in:
Victor Oliveira 2020-10-09 08:25:23 -03:00 committed by Scott Lahteine
parent 6d9709e20d
commit 59b6b32e6e
20 changed files with 269 additions and 38 deletions
Show stats Download patch file Download diff file Expand all files Collapse all files

2
Marlin/src/HAL/AVR/HAL.h
View file

@ -120,6 +120,8 @@ void HAL_init();
inline void HAL_clear_reset_source() { MCUSR = 0; }
inline uint8_t HAL_get_reset_source() { return MCUSR; }
inline void HAL_reboot() {} // reboot the board or restart the bootloader
#pragma GCC diagnostic push
#pragma GCC diagnostic ignored "-Wunused-function"
extern "C" {

2
Marlin/src/HAL/DUE/HAL.h
View file

@ -105,6 +105,8 @@ void sei(); // Enable interrupts
void HAL_clear_reset_source(); // clear reset reason
uint8_t HAL_get_reset_source(); // get reset reason
inline void HAL_reboot() {} // reboot the board or restart the bootloader
//
// ADC
//

2
Marlin/src/HAL/ESP32/HAL.h
View file

@ -96,6 +96,8 @@ void HAL_clear_reset_source();
// reset reason
uint8_t HAL_get_reset_source();
inline void HAL_reboot() {} // reboot the board or restart the bootloader
void _delay_ms(int delay);
#pragma GCC diagnostic push

2
Marlin/src/HAL/LINUX/HAL.h
View file

@ -101,6 +101,8 @@ uint16_t HAL_adc_get_result();
inline void HAL_clear_reset_source(void) {}
inline uint8_t HAL_get_reset_source(void) { return RST_POWER_ON; }
inline void HAL_reboot() {} // reboot the board or restart the bootloader
/* ---------------- Delay in cycles */
FORCE_INLINE static void DELAY_CYCLES(uint64_t x) {
Clock::delayCycles(x);

2
Marlin/src/HAL/LPC1768/HAL.h
View file

@ -200,6 +200,8 @@ void set_pwm_duty(const pin_t pin, const uint16_t v, const uint16_t v_size=255,
void HAL_clear_reset_source(void);
uint8_t HAL_get_reset_source(void);
inline void HAL_reboot() {} // reboot the board or restart the bootloader
// Add strcmp_P if missing
#ifndef strcmp_P
#define strcmp_P(a, b) strcmp((a), (b))

2
Marlin/src/HAL/SAMD51/HAL.h
View file

@ -88,6 +88,8 @@ typedef int8_t pin_t;
void HAL_clear_reset_source(); // clear reset reason
uint8_t HAL_get_reset_source(); // get reset reason
inline void HAL_reboot() {} // reboot the board or restart the bootloader
//
// ADC
//

2
Marlin/src/HAL/STM32/HAL.h
View file

@ -134,6 +134,8 @@ void HAL_clear_reset_source();
// Reset reason
uint8_t HAL_get_reset_source();
inline void HAL_reboot() {} // reboot the board or restart the bootloader
void _delay_ms(const int delay);
extern "C" char* _sbrk(int incr);

2
Marlin/src/HAL/STM32F1/HAL.h
View file

@ -185,6 +185,8 @@ void HAL_clear_reset_source();
// Reset reason
uint8_t HAL_get_reset_source();
inline void HAL_reboot() {} // reboot the board or restart the bootloader
void _delay_ms(const int delay);
#pragma GCC diagnostic push

2
Marlin/src/HAL/STM32_F4_F7/HAL.h
View file

@ -142,6 +142,8 @@ void HAL_clear_reset_source();
// Reset reason
uint8_t HAL_get_reset_source();
inline void HAL_reboot() {} // reboot the board or restart the bootloader
void _delay_ms(const int delay);
/*

2
Marlin/src/HAL/TEENSY31_32/HAL.h
View file

@ -93,6 +93,8 @@ void HAL_clear_reset_source();
// Get the reason for the reset
uint8_t HAL_get_reset_source();
inline void HAL_reboot() {} // reboot the board or restart the bootloader
FORCE_INLINE void _delay_ms(const int delay_ms) { delay(delay_ms); }
#pragma GCC diagnostic push

2
Marlin/src/HAL/TEENSY35_36/HAL.h
View file

@ -99,6 +99,8 @@ void HAL_clear_reset_source();
// Reset reason
uint8_t HAL_get_reset_source();
inline void HAL_reboot() {} // reboot the board or restart the bootloader
FORCE_INLINE void _delay_ms(const int delay_ms) { delay(delay_ms); }
#pragma GCC diagnostic push

1
Marlin/src/core/macros.h
View file

@ -215,6 +215,7 @@
#define WITHIN(N,L,H) ((N) >= (L) && (N) <= (H))
#define NUMERIC(a) WITHIN(a, '0', '9')
#define DECIMAL(a) (NUMERIC(a) || a == '.')
#define HEXCHR(a) (NUMERIC(a) ? (a) - '0' : WITHIN(a, 'a', 'f') ? ((a) - 'a' + 10) : WITHIN(a, 'A', 'F') ? ((a) - 'A' + 10) : -1)
#define NUMERIC_SIGNED(a) (NUMERIC(a) || (a) == '-' || (a) == '+')
#define DECIMAL_SIGNED(a) (DECIMAL(a) || (a) == '-' || (a) == '+')
#define COUNT(a) (sizeof(a)/sizeof(*a))

11
Marlin/src/feature/e_parser.h
View file

@ -88,10 +88,8 @@ public:
case EP_N:
switch (c) {
case '0': case '1': case '2':
case '3': case '4': case '5':
case '6': case '7': case '8':
case '9': case '-': case ' ': break;
case '0' ... '9':
case '-': case ' ': break;
case 'M': state = EP_M; break;
default: state = EP_IGNORE;
}
@ -153,10 +151,7 @@ public:
case EP_M876S:
switch (c) {
case ' ': break;
case '0': case '1': case '2':
case '3': case '4': case '5':
case '6': case '7': case '8':
case '9':
case '0' ... '9':
state = EP_M876SN;
M876_reason = (uint8_t)(c - '0');
break;

2
Marlin/src/gcode/control/T.cpp
View file

@ -46,7 +46,7 @@
* Tx Same as T?, but nozzle doesn't have to be preheated. Tc requires a preheated nozzle to finish filament load.
* Tc Load to nozzle after filament was prepared by Tc and nozzle is already heated.
*/
void GcodeSuite::T(const uint8_t tool_index) {
void GcodeSuite::T(const int8_t tool_index) {
DEBUG_SECTION(log_T, "T", DEBUGGING(LEVELING));
if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPAIR("...(", tool_index, ")");

4
Marlin/src/gcode/gcode.cpp
View file

@ -923,6 +923,10 @@ void GcodeSuite::process_parsed_command(const bool no_ok/*=false*/) {
case 'T': T(parser.codenum); break; // Tn: Tool Change
#if ENABLED(MARLIN_DEV_MODE)
case 'D': D(parser.codenum); break; // Dn: Debug codes
#endif
default:
#if ENABLED(WIFI_CUSTOM_COMMAND)
if (wifi_custom_command(parser.command_ptr)) break;

5
Marlin/src/gcode/gcode.h
View file

@ -285,6 +285,7 @@
* M995 - Touch screen calibration for TFT display
* M997 - Perform in-application firmware update
* M999 - Restart after being stopped by error
* D... - Custom Development G-code. Add hooks to 'gcode_D.cpp' for developers to test features. (Requires MARLIN_DEV_MODE)
*
* "T" Codes
*
@ -408,6 +409,8 @@ public:
private:
TERN_(MARLIN_DEV_MODE, static void D(const int16_t dcode));
static void G0_G1(TERN_(HAS_FAST_MOVES, const bool fast_move=false));
TERN_(ARC_SUPPORT, static void G2_G3(const bool clockwise));
@ -882,7 +885,7 @@ private:
TERN_(CONTROLLER_FAN_EDITABLE, static void M710());
static void T(const uint8_t tool_index);
static void T(const int8_t tool_index);
};

173
Marlin/src/gcode/gcode_d.cpp Normal file
View file

@ -0,0 +1,173 @@
/**
* Marlin 3D Printer Firmware
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <https://www.gnu.org/licenses/>.
*
*/
#include "../inc/MarlinConfigPre.h"
#if ENABLED(MARLIN_DEV_MODE)
#include "gcode.h"
#include "../module/settings.h"
#include "../libs/hex_print.h"
#include "../HAL/shared/eeprom_if.h"
/**
* Dn: G-code for development and testing
*
* See https://reprap.org/wiki/G-code#D:_Debug_codes
*
* Put whatever else you need here to test ongoing development.
*/
void GcodeSuite::D(const int16_t dcode) {
switch (dcode) {
case -1:
for (;;); // forever
case 0:
HAL_reboot();
break;
case 1: {
// Zero or pattern-fill the EEPROM data
#if ENABLED(EEPROM_SETTINGS)
persistentStore.access_start();
size_t total = persistentStore.capacity();
int pos = 0;
const uint8_t value = 0x0;
while(total--) {
persistentStore.write_data(pos, &value, 1);
}
persistentStore.access_finish();
#else
settings.reset();
settings.save();
#endif
HAL_reboot();
} break;
case 2: { // D2 Read / Write SRAM
#define SRAM_SIZE 8192
uint8_t *pointer = parser.hex_adr_val('A');
uint16_t len = parser.ushortval('C', 1);
uintptr_t addr = (uintptr_t)pointer;
NOMORE(addr, (size_t)(SRAM_SIZE - 1));
NOMORE(len, SRAM_SIZE - addr);
if (parser.seenval('X')) {
// Write the hex bytes after the X
uint16_t val = parser.hex_val('X');
while (len--) {
*pointer = val;
pointer++;
}
}
else {
while (len--) print_hex_byte(*(pointer++));
SERIAL_EOL();
}
} break;
case 3: { // D3 Read / Write EEPROM
uint8_t *pointer = parser.hex_adr_val('A');
uint16_t len = parser.ushortval('C', 1);
uintptr_t addr = (uintptr_t)pointer;
#ifndef MARLIN_EEPROM_SIZE
#define MARLIN_EEPROM_SIZE size_t(E2END + 1)
#endif
NOMORE(addr, (size_t)(MARLIN_EEPROM_SIZE - 1));
NOMORE(len, MARLIN_EEPROM_SIZE - addr);
if (parser.seenval('X')) {
uint16_t val = parser.hex_val('X');
#if ENABLED(EEPROM_SETTINGS)
persistentStore.access_start();
while(len--) {
int pos = 0;
persistentStore.write_data(pos, (uint8_t *)&val, sizeof(val));
}
SERIAL_EOL();
persistentStore.access_finish();
#else
SERIAL_ECHOLN("NO EEPROM");
#endif
}
else {
while (len--) {
// Read bytes from EEPROM
#if ENABLED(EEPROM_SETTINGS)
persistentStore.access_start();
uint8_t val;
while(len--) {
int pos = 0;
if (!persistentStore.read_data(pos, (uint8_t *)&val, sizeof(val))) {
print_hex_byte(val);
}
}
SERIAL_EOL();
persistentStore.access_finish();
#else
SERIAL_ECHOLN("NO EEPROM");
#endif
}
SERIAL_EOL();
}
} break;
case 4: { // D4 Read / Write PIN
// const uint8_t pin = parser.byteval('P');
// const bool is_out = parser.boolval('F'),
// val = parser.byteval('V', LOW);
if (parser.seenval('X')) {
// TODO: Write the hex bytes after the X
//while (len--) {
//}
}
else {
// while (len--) {
// TODO: Read bytes from EEPROM
// print_hex_byte(eeprom_read_byte(*(adr++));
// }
SERIAL_EOL();
}
} break;
case 5: { // D4 Read / Write onboard Flash
#define FLASH_SIZE 1024
uint8_t *pointer = parser.hex_adr_val('A');
uint16_t len = parser.ushortval('C', 1);
uintptr_t addr = (uintptr_t)pointer;
NOMORE(addr, (size_t)(FLASH_SIZE - 1));
NOMORE(len, FLASH_SIZE - addr);
if (parser.seenval('X')) {
// TODO: Write the hex bytes after the X
//while (len--) {
//}
}
else {
// while (len--) {
// TODO: Read bytes from EEPROM
// print_hex_byte(eeprom_read_byte(adr++));
// }
SERIAL_EOL();
}
} break;
}
}
#endif

49
Marlin/src/gcode/parser.cpp
View file

@ -147,22 +147,15 @@ void GCodeParser::parse(char *p) {
starpos[1] = '\0';
}
#if ENABLED(GCODE_MOTION_MODES)
#if ENABLED(ARC_SUPPORT)
#define GTOP 3
#else
#define GTOP 1
#endif
#if ANY(MARLIN_DEV_MODE, SWITCHING_TOOLHEAD, MAGNETIC_SWITCHING_TOOLHEAD, ELECTROMAGNETIC_SWITCHING_TOOLHEAD)
#define SIGNED_CODENUM 1
#endif
// Bail if the letter is not G, M, or T
// (or a valid parameter for the current motion mode)
switch (letter) {
case 'G': case 'M': case 'T':
#if ENABLED(CANCEL_OBJECTS)
case 'O':
#endif
case 'G': case 'M': case 'T': TERN_(MARLIN_DEV_MODE, case 'D':)
// Skip spaces to get the numeric part
while (*p == ' ') p++;
@ -178,22 +171,33 @@ void GCodeParser::parse(char *p) {
#endif
// Bail if there's no command code number
if (!NUMERIC(*p)) return;
if (!TERN(SIGNED_CODENUM, NUMERIC_SIGNED(*p), NUMERIC(*p))) return;
// Save the command letter at this point
// A '?' signifies an unknown command
command_letter = letter;
// Get the code number - integer digits only
codenum = 0;
do { codenum *= 10, codenum += *p++ - '0'; } while (NUMERIC(*p));
{
#if ENABLED(SIGNED_CODENUM)
int sign = 1; // Allow for a negative code like D-1 or T-1
if (*p == '-') { sign = -1; ++p; }
#endif
// Get the code number - integer digits only
codenum = 0;
do { codenum = codenum * 10 + *p++ - '0'; } while (NUMERIC(*p));
// Apply the sign, if any
TERN_(SIGNED_CODENUM, codenum *= sign);
}
// Allow for decimal point in command
#if ENABLED(USE_GCODE_SUBCODES)
if (*p == '.') {
p++;
while (NUMERIC(*p))
subcode *= 10, subcode += *p++ - '0';
subcode = subcode * 10 + *p++ - '0';
}
#endif
@ -201,11 +205,8 @@ void GCodeParser::parse(char *p) {
while (*p == ' ') p++;
#if ENABLED(GCODE_MOTION_MODES)
if (letter == 'G' && (codenum <= GTOP || codenum == 5
#if ENABLED(G38_PROBE_TARGET)
|| codenum == 38
#endif
)
if (letter == 'G'
&& (codenum <= TERN(ARC_SUPPORT, 3, 1) || codenum == 5 || TERN0(G38_PROBE_TARGET, codenum == 38))
) {
motion_mode_codenum = codenum;
TERN_(USE_GCODE_SUBCODES, motion_mode_subcode = subcode);
@ -216,12 +217,12 @@ void GCodeParser::parse(char *p) {
#if ENABLED(GCODE_MOTION_MODES)
#if ENABLED(ARC_SUPPORT)
case 'I': case 'J': case 'R':
case 'I' ... 'J': case 'R':
if (motion_mode_codenum != 2 && motion_mode_codenum != 3) return;
#endif
case 'P': case 'Q':
case 'P' ... 'Q':
if (motion_mode_codenum != 5) return;
case 'X': case 'Y': case 'Z': case 'E': case 'F':
case 'X' ... 'Z': case 'E' ... 'F':
if (motion_mode_codenum < 0) return;
command_letter = 'G';
codenum = motion_mode_codenum;
@ -247,7 +248,7 @@ void GCodeParser::parse(char *p) {
#if ENABLED(EXPECTED_PRINTER_CHECK)
case 16:
#endif
case 23: case 28: case 30: case 33: case 117: case 118: case 928:
case 23: case 28: case 30: case 117 ... 118: case 928:
string_arg = unescape_string(p);
return;
default: break;

34
Marlin/src/gcode/parser.h
View file

@ -114,6 +114,11 @@ public:
return valid_signless(p) || ((p[0] == '-' || p[0] == '+') && valid_signless(&p[1])); // [-+]?.?[0-9]
}
FORCE_INLINE static bool valid_number(const char * const p) {
// TODO: With MARLIN_DEV_MODE allow HEX values starting with "x"
return valid_float(p);
}
#if ENABLED(FASTER_GCODE_PARSER)
FORCE_INLINE static bool valid_int(const char * const p) {
@ -142,8 +147,12 @@ public:
if (ind >= COUNT(param)) return false; // Only A-Z
const bool b = TEST32(codebits, ind);
if (b) {
char * const ptr = command_ptr + param[ind];
value_ptr = param[ind] && valid_float(ptr) ? ptr : nullptr;
if (param[ind]) {
char * const ptr = command_ptr + param[ind];
value_ptr = valid_number(ptr) ? ptr : nullptr;
}
else
value_ptr = nullptr;
}
return b;
}
@ -198,7 +207,7 @@ public:
static inline bool seen(const char c) {
char *p = strgchr(command_args, c);
const bool b = !!p;
if (b) value_ptr = valid_float(&p[1]) ? &p[1] : nullptr;
if (b) value_ptr = valid_number(&p[1]) ? &p[1] : nullptr;
return b;
}
@ -401,6 +410,25 @@ public:
static inline float linearval(const char c, const float dval=0) { return seenval(c) ? value_linear_units() : dval; }
static inline float celsiusval(const char c, const float dval=0) { return seenval(c) ? value_celsius() : dval; }
#if ENABLED(MARLIN_DEV_MODE)
static inline uint8_t* hex_adr_val(const char c, uint8_t * const dval=nullptr) {
if (!seen(c) || *value_ptr != 'x') return dval;
uint8_t *out = nullptr;
for (char *vp = value_ptr + 1; HEXCHR(*vp) >= 0; vp++)
out = (uint8_t*)((uintptr_t(out) << 8) | HEXCHR(*vp));
return out;
}
static inline uint16_t hex_val(const char c, uint16_t const dval=0) {
if (!seen(c) || *value_ptr != 'x') return dval;
uint16_t out = 0;
for (char *vp = value_ptr + 1; HEXCHR(*vp) >= 0; vp++)
out = ((out) << 8) | HEXCHR(*vp);
return out;
}
#endif
};
extern GCodeParser parser;

6
Marlin/src/lcd/ultralcd.cpp
View file

@ -123,11 +123,15 @@ constexpr uint8_t epps = ENCODER_PULSES_PER_STEP;
#include "lcdprint.h"
#include "../sd/cardreader.h"
#include "../module/settings.h"
#include "../module/temperature.h"
#include "../module/planner.h"
#include "../module/motion.h"
#if HAS_LCD_MENU
#include "../module/settings.h"
#endif
#if ENABLED(AUTO_BED_LEVELING_UBL)
#include "../feature/bedlevel/bedlevel.h"
#endif