zaubentrucker/muele-marlin
1
0
Fork 0
Code Issues Pull requests Actions Packages Projects Releases Wiki Activity

Misc. improvements (#12747)

Browse source 
* Make ExtUI respect MAXTEMP limits
  - Temperatures are now clamped by MAXTEMP limits rather than arbitrary values.
* Speed up USB init, add status
  - Speed up USB initialization
  - Show status message if init failed
* Enable status messages for EXTENSIBLE_UI
* Adjust max limit to MAX_TEMP - 15
* Misc. tweaks to formatting, const, etc.
This commit is contained in:
Marcio Teixeira 2019-01-01 14:17:48 -07:00 committed by Scott Lahteine
parent 4f2473053c
commit 60cb36bef3
12 changed files with 188 additions and 209 deletions
Show stats Download patch file Download diff file Expand all files Collapse all files

21
Marlin/src/HAL/HAL_LPC1768/u8g/u8g_com_HAL_LPC1768_st7920_hw_spi.cpp
View file

@ -80,20 +80,13 @@ static uint8_t rs_last_state = 255;
static void u8g_com_LPC1768_st7920_write_byte_hw_spi(uint8_t rs, uint8_t val) {
if ( rs != rs_last_state) { // time to send a command/data byte
if (rs != rs_last_state) { // Time to send a command/data byte
rs_last_state = rs;
if ( rs == 0 )
/* command */
spiSend(0x0F8);
else
/* data */
spiSend(0x0FA);
DELAY_US(40); // give the controller some time to process the data: 20 is bad, 30 is OK, 40 is safe
spiSend(rs ? 0x0FA : 0x0F8); // Send data or command
DELAY_US(40); // Give the controller some time: 20 is bad, 30 is OK, 40 is safe
}
spiSend(val & 0x0F0);
spiSend(val & 0xF0);
spiSend(val << 4);
}
@ -105,7 +98,7 @@ uint8_t u8g_com_HAL_LPC1768_ST7920_hw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t ar
u8g_Delay(5);
spiBegin();
spiInit(SPI_EIGHTH_SPEED); // ST7920 max speed is about 1.1 MHz
u8g->pin_list[U8G_PI_A0_STATE] = 0; /* inital RS state: command mode */
u8g->pin_list[U8G_PI_A0_STATE] = 0; // initial RS state: command mode
break;
case U8G_COM_MSG_STOP:
@ -115,12 +108,12 @@ uint8_t u8g_com_HAL_LPC1768_ST7920_hw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t ar
u8g_SetPILevel(u8g, U8G_PI_RESET, arg_val);
break;
case U8G_COM_MSG_ADDRESS: /* define cmd (arg_val = 0) or data mode (arg_val = 1) */
case U8G_COM_MSG_ADDRESS: // Define cmd (arg_val = 0) or data mode (arg_val = 1)
u8g->pin_list[U8G_PI_A0_STATE] = arg_val;
break;
case U8G_COM_MSG_CHIP_SELECT:
u8g_SetPILevel(u8g, U8G_PI_CS, arg_val); //note: the st7920 has an active high chip select
u8g_SetPILevel(u8g, U8G_PI_CS, arg_val); // Note: the ST7920 has an active high chip-select
break;
case U8G_COM_MSG_WRITE_BYTE:

2
Marlin/src/gcode/temperature/M104_M109.cpp
View file

@ -125,7 +125,7 @@ void GcodeSuite::M109() {
print_job_timer.start();
#endif
#if ENABLED(ULTRA_LCD)
#if ENABLED(ULTRA_LCD) || ENABLED(EXTENSIBLE_UI)
if (thermalManager.isHeatingHotend(target_extruder) || !no_wait_for_cooling)
thermalManager.set_heating_message(target_extruder);
#endif

10
Marlin/src/lcd/extensible_ui/ui_api.cpp
View file

@ -544,16 +544,20 @@ namespace ExtUI {
}
void setTargetTemp_celsius(float value, const heater_t heater) {
constexpr int16_t heater_maxtemp[HOTENDS] = ARRAY_BY_HOTENDS(HEATER_0_MAXTEMP, HEATER_1_MAXTEMP, HEATER_2_MAXTEMP, HEATER_3_MAXTEMP, HEATER_4_MAXTEMP);
const int16_t e = heater - H0;
#if HAS_HEATED_BED
if (heater == BED)
thermalManager.setTargetBed(clamp(value,0,200));
thermalManager.setTargetBed(clamp(value, 0, BED_MAXTEMP - 15));
else
#endif
thermalManager.setTargetHotend(clamp(value,0,500), heater - H0);
thermalManager.setTargetHotend(clamp(value, 0, heater_maxtemp[e] - 15), e);
}
void setTargetTemp_celsius(float value, const extruder_t extruder) {
thermalManager.setTargetHotend(clamp(value,0,500), extruder - E0);
constexpr int16_t heater_maxtemp[HOTENDS] = ARRAY_BY_HOTENDS(HEATER_0_MAXTEMP, HEATER_1_MAXTEMP, HEATER_2_MAXTEMP, HEATER_3_MAXTEMP, HEATER_4_MAXTEMP);
const int16_t e = extruder - E0;
thermalManager.setTargetHotend(clamp(value, 0, heater_maxtemp[e] - 15), e);
}
void setFan_percent(float value, const fan_t fan) {

2
Marlin/src/lcd/menu/menu_temperature.cpp
View file

@ -44,7 +44,7 @@ uint8_t MarlinUI::preheat_fan_speed[2];
//
void _lcd_preheat(const int16_t endnum, const int16_t temph, const int16_t tempb, const uint8_t fan) {
if (temph > 0) thermalManager.setTargetHotend(MIN(heater_maxtemp[endnum], temph), endnum);
if (temph > 0) thermalManager.setTargetHotend(MIN(heater_maxtemp[endnum] - 15, temph), endnum);
#if HAS_HEATED_BED
if (tempb >= 0) thermalManager.setTargetBed(tempb);
#else

4
Marlin/src/module/motion.cpp
View file

@ -47,7 +47,7 @@
#include "../feature/bedlevel/bedlevel.h"
#endif
#if HAS_AXIS_UNHOMED_ERR && ENABLED(ULTRA_LCD)
#if HAS_AXIS_UNHOMED_ERR && (ENABLED(ULTRA_LCD) || ENABLED(EXTENSIBLE_UI))
#include "../lcd/ultralcd.h"
#endif
@ -1019,7 +1019,7 @@ void prepare_move_to_destination() {
if (zz) SERIAL_ECHOPGM(MSG_Z);
SERIAL_ECHOLNPGM(" " MSG_FIRST);
#if ENABLED(ULTRA_LCD)
#if ENABLED(ULTRA_LCD) || ENABLED(EXTENSIBLE_UI)
ui.status_printf_P(0, PSTR(MSG_HOME " %s%s%s " MSG_FIRST), xx ? MSG_X : "", yy ? MSG_Y : "", zz ? MSG_Z : "");
#endif
return true;

2
Marlin/src/module/temperature.cpp
View file

@ -2470,7 +2470,7 @@ void Temperature::isr() {
#endif // AUTO_REPORT_TEMPERATURES
#if ENABLED(ULTRA_LCD)
#if ENABLED(ULTRA_LCD) || ENABLED(EXTENSIBLE_UI)
void Temperature::set_heating_message(const uint8_t e) {
const bool heating = isHeatingHotend(e);
#if HOTENDS > 1

2
Marlin/src/module/tool_change.cpp
View file

@ -681,7 +681,7 @@ void tool_change(const uint8_t tmp_extruder, const float fr_mm_s/*=0.0*/, bool n
singlenozzle_temp[active_extruder] = thermalManager.target_temperature[0];
if (singlenozzle_temp[tmp_extruder] && singlenozzle_temp[tmp_extruder] != singlenozzle_temp[active_extruder]) {
thermalManager.setTargetHotend(singlenozzle_temp[tmp_extruder], 0);
#if ENABLED(ULTRA_LCD)
#if ENABLED(ULTRA_LCD) || ENABLED(EXTENSIBLE_UI)
thermalManager.set_heating_message(0);
#endif
(void)thermalManager.wait_for_hotend(0, false); // Wait for heating or cooling

229
Marlin/src/sd/Sd2Card.cpp
View file

@ -87,44 +87,42 @@
#endif
#endif
// send command and return error code. Return zero for OK
uint8_t Sd2Card::cardCommand(uint8_t cmd, uint32_t arg) {
// select card
// Send command and return error code. Return zero for OK
uint8_t Sd2Card::cardCommand(const uint8_t cmd, const uint32_t arg) {
// Select card
chipSelect();
// wait up to 300 ms if busy
// Wait up to 300 ms if busy
waitNotBusy(SD_WRITE_TIMEOUT);
uint8_t *pa = (uint8_t *)(&arg);
#if ENABLED(SD_CHECK_AND_RETRY)
// form message
// Form message
uint8_t d[6] = {(uint8_t) (cmd | 0x40), pa[3], pa[2], pa[1], pa[0] };
// add crc
// Add crc
d[5] = CRC7(d, 5);
// send message
for (uint8_t k = 0; k < 6; k++ )
spiSend( d[k] );
// Send message
for (uint8_t k = 0; k < 6; k++) spiSend(d[k]);
#else
// send command
// Send command
spiSend(cmd | 0x40);
// send argument
for( int8_t i = 3; i >= 0; i-- )
spiSend( pa[i] );
// Send argument
for (int8_t i = 3; i >= 0; i--) spiSend(pa[i]);
// send CRC - correct for CMD0 with arg zero or CMD8 with arg 0X1AA
// Send CRC - correct for CMD0 with arg zero or CMD8 with arg 0X1AA
spiSend(cmd == CMD0 ? 0X95 : 0X87);
#endif
// skip stuff byte for stop read
// Skip stuff byte for stop read
if (cmd == CMD12) spiRec();
// wait for response
// Wait for response
for (uint8_t i = 0; ((status_ = spiRec()) & 0x80) && i != 0xFF; i++) { /* Intentionally left empty */ }
return status_;
}
@ -159,9 +157,7 @@ uint32_t Sd2Card::cardSize() {
void Sd2Card::chipDeselect() {
digitalWrite(chipSelectPin_, HIGH);
// insure MISO goes high impedance
spiSend( 0xFF );
spiSend(0xFF); // Ensure MISO goes high impedance
}
void Sd2Card::chipSelect() {
@ -195,13 +191,8 @@ bool Sd2Card::erase(uint32_t firstBlock, uint32_t lastBlock) {
goto FAIL;
}
}
if (type_ != SD_CARD_TYPE_SDHC) {
firstBlock <<= 9;
lastBlock <<= 9;
}
if (cardCommand(CMD32, firstBlock)
|| cardCommand(CMD33, lastBlock)
|| cardCommand(CMD38, 0)) {
if (type_ != SD_CARD_TYPE_SDHC) { firstBlock <<= 9; lastBlock <<= 9; }
if (cardCommand(CMD32, firstBlock) || cardCommand(CMD33, lastBlock) || cardCommand(CMD38, 0)) {
error(SD_CARD_ERROR_ERASE);
goto FAIL;
}
@ -236,7 +227,7 @@ bool Sd2Card::eraseSingleBlockEnable() {
* \return true for success, false for failure.
* The reason for failure can be determined by calling errorCode() and errorData().
*/
bool Sd2Card::init(uint8_t sckRateID, pin_t chipSelectPin) {
bool Sd2Card::init(const uint8_t sckRateID/*=0*/, const pin_t chipSelectPin/*=SD_CHIP_SELECT_PIN*/) {
errorCode_ = type_ = 0;
chipSelectPin_ = chipSelectPin;
// 16-bit init start time allows over a minute
@ -308,23 +299,23 @@ bool Sd2Card::init(uint8_t sckRateID, pin_t chipSelectPin) {
watchdog_reset();
#endif
// initialize card and send host supports SDHC if SD2
// Initialize card and send host supports SDHC if SD2
arg = type() == SD_CARD_TYPE_SD2 ? 0x40000000 : 0;
while ((status_ = cardAcmd(ACMD41, arg)) != R1_READY_STATE) {
// check for timeout
// Check for timeout
if (ELAPSED(millis(), init_timeout)) {
error(SD_CARD_ERROR_ACMD41);
goto FAIL;
}
}
// if SD2 read OCR register to check for SDHC card
// If SD2 read OCR register to check for SDHC card
if (type() == SD_CARD_TYPE_SD2) {
if (cardCommand(CMD58, 0)) {
error(SD_CARD_ERROR_CMD58);
goto FAIL;
}
if ((spiRec() & 0xC0) == 0xC0) type(SD_CARD_TYPE_SDHC);
// discard rest of ocr - contains allowed voltage range
// Discard rest of ocr - contains allowed voltage range
for (uint8_t i = 0; i < 3; i++) spiRec();
}
chipDeselect();
@ -344,8 +335,7 @@ bool Sd2Card::init(uint8_t sckRateID, pin_t chipSelectPin) {
* \return true for success, false for failure.
*/
bool Sd2Card::readBlock(uint32_t blockNumber, uint8_t* dst) {
// use address if not SDHC card
if (type() != SD_CARD_TYPE_SDHC) blockNumber <<= 9;
if (type() != SD_CARD_TYPE_SDHC) blockNumber <<= 9; // Use address if not SDHC card
#if ENABLED(SD_CHECK_AND_RETRY)
uint8_t retryCnt = 3;
@ -447,44 +437,39 @@ bool Sd2Card::readData(uint8_t* dst) {
#endif
#endif // SD_CHECK_AND_RETRY
bool Sd2Card::readData(uint8_t* dst, uint16_t count) {
// wait for start block token
bool Sd2Card::readData(uint8_t* dst, const uint16_t count) {
bool success = false;
const millis_t read_timeout = millis() + SD_READ_TIMEOUT;
while ((status_ = spiRec()) == 0xFF) {
while ((status_ = spiRec()) == 0xFF) { // Wait for start block token
if (ELAPSED(millis(), read_timeout)) {
error(SD_CARD_ERROR_READ_TIMEOUT);
goto FAIL;
}
}
if (status_ != DATA_START_BLOCK) {
error(SD_CARD_ERROR_READ);
goto FAIL;
}
// transfer data
spiRead(dst, count);
if (status_ == DATA_START_BLOCK) {
spiRead(dst, count); // Transfer data
const uint16_t recvCrc = (spiRec() << 8) | spiRec();
#if ENABLED(SD_CHECK_AND_RETRY)
{
uint16_t recvCrc = (spiRec() << 8) | spiRec();
if (crcSupported && recvCrc != CRC_CCITT(dst, count)) {
error(SD_CARD_ERROR_READ_CRC);
goto FAIL;
}
}
success = !crcSupported || recvCrc == CRC_CCITT(dst, count);
if (!success) error(SD_CARD_ERROR_READ_CRC);
#else
// discard CRC
spiRec();
spiRec();
success = true;
UNUSED(recvCrc);
#endif
chipDeselect();
return true;
}
else
error(SD_CARD_ERROR_READ);
FAIL:
chipDeselect();
return false;
return success;
}
/** read CID or CSR register */
bool Sd2Card::readRegister(uint8_t cmd, void* buf) {
bool Sd2Card::readRegister(const uint8_t cmd, void* buf) {
uint8_t* dst = reinterpret_cast<uint8_t*>(buf);
if (cardCommand(cmd, 0)) {
error(SD_CARD_ERROR_READ_REG);
@ -506,13 +491,11 @@ bool Sd2Card::readRegister(uint8_t cmd, void* buf) {
*/
bool Sd2Card::readStart(uint32_t blockNumber) {
if (type() != SD_CARD_TYPE_SDHC) blockNumber <<= 9;
if (cardCommand(CMD18, blockNumber)) {
error(SD_CARD_ERROR_CMD18);
const bool success = !cardCommand(CMD18, blockNumber);
if (!success) error(SD_CARD_ERROR_CMD18);
chipDeselect();
return false;
}
chipDeselect();
return true;
return success;
}
/**
@ -522,13 +505,10 @@ bool Sd2Card::readStart(uint32_t blockNumber) {
*/
bool Sd2Card::readStop() {
chipSelect();
if (cardCommand(CMD12, 0)) {
error(SD_CARD_ERROR_CMD12);
const bool success = !cardCommand(CMD12, 0);
if (!success) error(SD_CARD_ERROR_CMD12);
chipDeselect();
return false;
}
chipDeselect();
return true;
return success;
}
/**
@ -543,16 +523,20 @@ bool Sd2Card::readStop() {
* \return The value one, true, is returned for success and the value zero,
* false, is returned for an invalid value of \a sckRateID.
*/
bool Sd2Card::setSckRate(uint8_t sckRateID) {
if (sckRateID > 6) {
error(SD_CARD_ERROR_SCK_RATE);
return false;
}
bool Sd2Card::setSckRate(const uint8_t sckRateID) {
const bool success = (sckRateID <= 6);
if (success)
spiRate_ = sckRateID;
return true;
else
error(SD_CARD_ERROR_SCK_RATE);
return success;
}
// wait for card to go not busy
/**
* Wait for card to become not-busy
* \param[in] timeout_ms Timeout to abort.
* \return true for success, false for timeout.
*/
bool Sd2Card::waitNotBusy(const millis_t timeout_ms) {
const millis_t wait_timeout = millis() + timeout_ms;
while (spiRec() != 0xFF)
@ -562,36 +546,31 @@ bool Sd2Card::waitNotBusy(const millis_t timeout_ms) {
}
/**
* Writes a 512 byte block to an SD card.
* Write a 512 byte block to an SD card.
*
* \param[in] blockNumber Logical block to be written.
* \param[in] src Pointer to the location of the data to be written.
* \return true for success, false for failure.
*/
bool Sd2Card::writeBlock(uint32_t blockNumber, const uint8_t* src) {
// use address if not SDHC card
if (type() != SD_CARD_TYPE_SDHC) blockNumber <<= 9;
if (cardCommand(CMD24, blockNumber)) {
error(SD_CARD_ERROR_CMD24);
goto FAIL;
}
if (!writeData(DATA_START_BLOCK, src)) goto FAIL;
if (type() != SD_CARD_TYPE_SDHC) blockNumber <<= 9; // Use address if not SDHC card
// wait for flash programming to complete
if (!waitNotBusy(SD_WRITE_TIMEOUT)) {
bool success = false;
if (!cardCommand(CMD24, blockNumber)) {
if (writeData(DATA_START_BLOCK, src)) {
if (waitNotBusy(SD_WRITE_TIMEOUT)) { // Wait for flashing to complete
success = !(cardCommand(CMD13, 0) || spiRec()); // Response is r2 so get and check two bytes for nonzero
if (!success) error(SD_CARD_ERROR_WRITE_PROGRAMMING);
}
else
error(SD_CARD_ERROR_WRITE_TIMEOUT);
goto FAIL;
}
// response is r2 so get and check two bytes for nonzero
if (cardCommand(CMD13, 0) || spiRec()) {
error(SD_CARD_ERROR_WRITE_PROGRAMMING);
goto FAIL;
}
else
error(SD_CARD_ERROR_CMD24);
chipDeselect();
return true;
FAIL:
chipDeselect();
return false;
return success;
}
/**
@ -600,28 +579,30 @@ bool Sd2Card::writeBlock(uint32_t blockNumber, const uint8_t* src) {
* \return true for success, false for failure.
*/
bool Sd2Card::writeData(const uint8_t* src) {
bool success = true;
chipSelect();
// wait for previous write to finish
// Wait for previous write to finish
if (!waitNotBusy(SD_WRITE_TIMEOUT) || !writeData(WRITE_MULTIPLE_TOKEN, src)) {
error(SD_CARD_ERROR_WRITE_MULTIPLE);
chipDeselect();
return false;
success = false;
}
chipDeselect();
return true;
return success;
}
// send one block of data for write block or write multiple blocks
bool Sd2Card::writeData(uint8_t token, const uint8_t* src) {
// Send one block of data for write block or write multiple blocks
bool Sd2Card::writeData(const uint8_t token, const uint8_t* src) {
uint16_t crc =
#if ENABLED(SD_CHECK_AND_RETRY)
uint16_t crc = CRC_CCITT( src, 512 );
#else // ENABLED(SD_CHECK_AND_RETRY)
uint16_t crc = 0xFFFF;
#endif // ENABLED(SD_CHECK_AND_RETRY)
CRC_CCITT(src, 512)
#else
0xFFFF
#endif
;
spiSendBlock(token, src);
spiSend(crc >> 8);
spiSend( crc & 0XFF );
spiSend(crc & 0xFF);
status_ = spiRec();
if ((status_ & DATA_RES_MASK) != DATA_RES_ACCEPTED) {
@ -643,23 +624,18 @@ bool Sd2Card::writeData(uint8_t token, const uint8_t* src) {
*
* \return true for success, false for failure.
*/
bool Sd2Card::writeStart(uint32_t blockNumber, uint32_t eraseCount) {
// send pre-erase count
if (cardAcmd(ACMD23, eraseCount)) {
bool Sd2Card::writeStart(uint32_t blockNumber, const uint32_t eraseCount) {
bool success = false;
if (!cardAcmd(ACMD23, eraseCount)) { // Send pre-erase count
if (type() != SD_CARD_TYPE_SDHC) blockNumber <<= 9; // Use address if not SDHC card
success = !cardCommand(CMD25, blockNumber);
if (!success) error(SD_CARD_ERROR_CMD25);
}
else
error(SD_CARD_ERROR_ACMD23);
goto FAIL;
}
// use address if not SDHC card
if (type() != SD_CARD_TYPE_SDHC) blockNumber <<= 9;
if (cardCommand(CMD25, blockNumber)) {
error(SD_CARD_ERROR_CMD25);
goto FAIL;
}
chipDeselect();
return true;
FAIL:
chipDeselect();
return false;
return success;
}
/**
@ -668,16 +644,17 @@ bool Sd2Card::writeStart(uint32_t blockNumber, uint32_t eraseCount) {
* \return true for success, false for failure.
*/
bool Sd2Card::writeStop() {
bool success = false;
chipSelect();
if (!waitNotBusy(SD_WRITE_TIMEOUT)) goto FAIL;
if (waitNotBusy(SD_WRITE_TIMEOUT)) {
spiSend(STOP_TRAN_TOKEN);
if (!waitNotBusy(SD_WRITE_TIMEOUT)) goto FAIL;
chipDeselect();
return true;
FAIL:
success = waitNotBusy(SD_WRITE_TIMEOUT);
}
else
error(SD_CARD_ERROR_STOP_TRAN);
chipDeselect();
return false;
return success;
}
#endif // SDSUPPORT

29
Marlin/src/sd/Sd2Card.h
View file

@ -124,15 +124,15 @@ class Sd2Card {
* Set SD error code.
* \param[in] code value for error code.
*/
void error(uint8_t code) {errorCode_ = code;}
inline void error(const uint8_t code) { errorCode_ = code; }
/**
* \return error code for last error. See Sd2Card.h for a list of error codes.
*/
int errorCode() const {return errorCode_;}
inline int errorCode() const { return errorCode_; }
/** \return error data for last error. */
int errorData() const {return status_;}
inline int errorData() const { return status_; }
/**
* Initialize an SD flash memory card with default clock rate and chip
@ -140,8 +140,8 @@ class Sd2Card {
*
* \return true for success or false for failure.
*/
bool init(uint8_t sckRateID = SPI_FULL_SPEED,
pin_t chipSelectPin = SD_CHIP_SELECT_PIN);
bool init(const uint8_t sckRateID=SPI_FULL_SPEED, const pin_t chipSelectPin=SD_CHIP_SELECT_PIN);
bool readBlock(uint32_t block, uint8_t* dst);
/**
@ -163,12 +163,13 @@ class Sd2Card {
*
* \return true for success or false for failure.
*/
bool readCSD(csd_t* csd) { return readRegister(CMD9, csd); }
inline bool readCSD(csd_t* csd) { return readRegister(CMD9, csd); }
bool readData(uint8_t* dst);
bool readStart(uint32_t blockNumber);
bool readStop();
bool setSckRate(uint8_t sckRateID);
bool setSckRate(const uint8_t sckRateID);
/**
* Return the card type: SD V1, SD V2 or SDHC
* \return 0 - SD V1, 1 - SD V2, or 3 - SDHC.
@ -176,7 +177,7 @@ class Sd2Card {
int type() const {return type_;}
bool writeBlock(uint32_t blockNumber, const uint8_t* src);
bool writeData(const uint8_t* src);
bool writeStart(uint32_t blockNumber, uint32_t eraseCount);
bool writeStart(uint32_t blockNumber, const uint32_t eraseCount);
bool writeStop();
private:
@ -187,17 +188,17 @@ class Sd2Card {
type_;
// private functions
uint8_t cardAcmd(uint8_t cmd, uint32_t arg) {
inline uint8_t cardAcmd(const uint8_t cmd, const uint32_t arg) {
cardCommand(CMD55, 0);
return cardCommand(cmd, arg);
}
uint8_t cardCommand(uint8_t cmd, uint32_t arg);
uint8_t cardCommand(const uint8_t cmd, const uint32_t arg);
bool readData(uint8_t* dst, uint16_t count);
bool readRegister(uint8_t cmd, void* buf);
bool readData(uint8_t* dst, const uint16_t count);
bool readRegister(const uint8_t cmd, void* buf);
void chipDeselect();
void chipSelect();
void type(uint8_t value) { type_ = value; }
inline void type(const uint8_t value) { type_ = value; }
bool waitNotBusy(const millis_t timeout_ms);
bool writeData(uint8_t token, const uint8_t* src);
bool writeData(const uint8_t token, const uint8_t* src);
};

2
Marlin/src/sd/cardreader.cpp
View file

@ -1022,7 +1022,7 @@ void CardReader::printingHasFinished() {
presort();
#endif
#if ENABLED(ULTRA_LCD) && ENABLED(LCD_SET_PROGRESS_MANUALLY)
#if (ENABLED(ULTRA_LCD) || ENABLED(EXTENSIBLE_UI)) && ENABLED(LCD_SET_PROGRESS_MANUALLY)
ui.progress_bar_percent = 0;
#endif

24
Marlin/src/sd/usb_flashdrive/Sd2Card_FlashDrive.cpp
View file

@ -31,6 +31,10 @@
#include "Sd2Card_FlashDrive.h"
#if ENABLED(ULTRA_LCD) || ENABLED(EXTENSIBLE_UI)
#include "../../lcd/ultralcd.h"
#endif
USB usb;
BulkOnly bulk(&usb);
@ -46,25 +50,27 @@ void Sd2Card::idle() {
switch (state) {
case USB_HOST_DELAY_INIT:
next_retry = millis() + 10000;
next_retry = millis() + 2000;
state = USB_HOST_WAITING;
break;
case USB_HOST_WAITING:
if (ELAPSED(millis(), next_retry)) {
next_retry = millis() + 10000;
next_retry = millis() + 2000;
state = USB_HOST_UNINITIALIZED;
}
break;
case USB_HOST_UNINITIALIZED:
SERIAL_ECHOLNPGM("Starting USB host");
SERIAL_ECHOPGM("Starting USB host...");
if (!usb.start()) {
SERIAL_ECHOLNPGM("USB host failed to start. Will retry in 10 seconds.");
SERIAL_ECHOPGM(" Failed. Retrying in 2s.");
#if ENABLED(ULTRA_LCD) || ENABLED(EXTENSIBLE_UI)
LCD_MESSAGEPGM("USB start failed");
#endif
state = USB_HOST_DELAY_INIT;
}
else {
SERIAL_ECHOLNPGM("USB host initialized");
else
state = USB_HOST_INITIALIZED;
}
SERIAL_EOL();
break;
case USB_HOST_INITIALIZED:
const uint8_t lastUsbTaskState = usb.getUsbTaskState();
@ -91,10 +97,10 @@ void Sd2Card::idle() {
// This is equivalent to polling the SD_DETECT when using SD cards.
bool Sd2Card::isInserted() {
return usb.getUsbTaskState() == USB_STATE_RUNNING;
};
}
// Marlin calls this to initialize an SD card once it is inserted.
bool Sd2Card::init(uint8_t sckRateID, uint8_t chipSelectPin) {
bool Sd2Card::init(const uint8_t sckRateID/*=0*/, const pin_t chipSelectPin/*=SD_CHIP_SELECT_PIN*/) {
if (!ready()) return false;
if (!bulk.LUNIsGood(0)) {

24
Marlin/src/sd/usb_flashdrive/Sd2Card_FlashDrive.h
View file

@ -32,7 +32,6 @@
*/
//#define USB_DEBUG 1
#include "../SdFatConfig.h"
#include "../SdInfo.h"
@ -61,11 +60,11 @@
class Sd2Card {
private:
typedef enum {
USB_HOST_DELAY_INIT,
USB_HOST_WAITING,
typedef enum : uint8_t {
USB_HOST_UNINITIALIZED,
USB_HOST_INITIALIZED
USB_HOST_INITIALIZED,
USB_HOST_DELAY_INIT,
USB_HOST_WAITING
} state_t;
static state_t state;
@ -78,18 +77,17 @@ class Sd2Card {
static inline bool ready() { return state == USB_HOST_INITIALIZED; }
public:
bool init(uint8_t sckRateID = 0, uint8_t chipSelectPin = SD_CHIP_SELECT_PIN);
bool init(const uint8_t sckRateID=0, const pin_t chipSelectPin=SD_CHIP_SELECT_PIN);
static void idle();
bool readStart(uint32_t block) { pos = block; return ready(); }
bool readData(uint8_t* dst) { return readBlock(pos++, dst); }
bool readStop() { return true; }
bool writeStart(uint32_t block, uint32_t eraseCount) { pos = block; return ready(); }
bool writeData(uint8_t* src) { return writeBlock(pos++, src); }
bool writeStop() { return true; }
inline bool readStart(const uint32_t block) { pos = block; return ready(); }
inline bool readData(uint8_t* dst) { return readBlock(pos++, dst); }
inline bool readStop() const { return true; }
inline bool writeStart(const uint32_t block, const uint32_t eraseCount) { UNUSED(eraseCount); pos = block; return ready(); }
inline bool writeData(uint8_t* src) { return writeBlock(pos++, src); }
inline bool writeStop() const { return true; }
bool readBlock(uint32_t block, uint8_t* dst);
bool writeBlock(uint32_t blockNumber, const uint8_t* src);