Merge pull request #1195 from thinkyhead/board_defines
Defines for electronics boards
This commit is contained in:
Bo Herrmannsen
commit
7458bfe297
|
|
@ -1,6 +1,8 @@
|
|||
#ifndef CONFIGURATION_H
|
||||
#define CONFIGURATION_H
|
||||
|
||||
#include "boards.h"
|
||||
|
||||
// This configuration file contains the basic settings.
|
||||
// Advanced settings can be found in Configuration_adv.h
|
||||
// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
|
||||
|
|
@ -36,54 +38,10 @@
|
|||
// This enables the serial port associated to the Bluetooth interface
|
||||
//#define BTENABLED // Enable BT interface on AT90USB devices
|
||||
|
||||
|
||||
//// The following define selects which electronics board you have. Please choose the one that matches your setup
|
||||
// 10 = Gen7 custom (Alfons3 Version) "https://github.com/Alfons3/Generation_7_Electronics"
|
||||
// 11 = Gen7 v1.1, v1.2 = 11
|
||||
// 12 = Gen7 v1.3
|
||||
// 13 = Gen7 v1.4
|
||||
// 2 = Cheaptronic v1.0
|
||||
// 20 = Sethi 3D_1
|
||||
// 3 = MEGA/RAMPS up to 1.2 = 3
|
||||
// 33 = RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Bed)
|
||||
// 34 = RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Bed)
|
||||
// 35 = RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Fan)
|
||||
// 36 = RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Fan)
|
||||
// 4 = Duemilanove w/ ATMega328P pin assignment
|
||||
// 5 = Gen6
|
||||
// 51 = Gen6 deluxe
|
||||
// 6 = Sanguinololu < 1.2
|
||||
// 62 = Sanguinololu 1.2 and above
|
||||
// 63 = Melzi
|
||||
// 64 = STB V1.1
|
||||
// 65 = Azteeg X1
|
||||
// 66 = Melzi with ATmega1284 (MaKr3d version)
|
||||
// 67 = Azteeg X3
|
||||
// 68 = Azteeg X3 Pro
|
||||
// 7 = Ultimaker
|
||||
// 71 = Ultimaker (Older electronics. Pre 1.5.4. This is rare)
|
||||
// 72 = Ultimainboard 2.x (Uses TEMP_SENSOR 20)
|
||||
// 77 = 3Drag Controller
|
||||
// 8 = Teensylu
|
||||
// 80 = Rumba
|
||||
// 81 = Printrboard (AT90USB1286)
|
||||
// 82 = Brainwave (AT90USB646)
|
||||
// 83 = SAV Mk-I (AT90USB1286)
|
||||
// 84 = Teensy++2.0 (AT90USB1286) // CLI compile: DEFINES=AT90USBxx_TEENSYPP_ASSIGNMENTS HARDWARE_MOTHERBOARD=84 make
|
||||
// 9 = Gen3+
|
||||
// 22 = Gen3 Monolithic Electronics
|
||||
// 70 = Megatronics
|
||||
// 701= Megatronics v2.0
|
||||
// 702= Minitronics v1.0
|
||||
// 90 = Alpha OMCA board
|
||||
// 91 = Final OMCA board
|
||||
// 301= Rambo
|
||||
// 21 = Elefu Ra Board (v3)
|
||||
// 88 = 5DPrint D8 Driver Board
|
||||
// 999 = Leapfrog
|
||||
|
||||
// The following define selects which electronics board you have.
|
||||
// Please choose the name from boards.h that matches your setup
|
||||
#ifndef MOTHERBOARD
|
||||
#define MOTHERBOARD 7
|
||||
#define MOTHERBOARD BOARD_ULTIMAKER
|
||||
#endif
|
||||
|
||||
// Define this to set a custom name for your generic Mendel,
|
||||
|
|
|
|||
55
Marlin/boards.h
Normal file
55
Marlin/boards.h
Normal file
|
|
@ -0,0 +1,55 @@
|
|||
#ifndef BOARDS_H
|
||||
#define BOARDS_H
|
||||
|
||||
#define BOARD_UNKNOWN -1
|
||||
|
||||
#define BOARD_GEN7_CUSTOM 10 // Gen7 custom (Alfons3 Version) "https://github.com/Alfons3/Generation_7_Electronics"
|
||||
#define BOARD_GEN7_12 11 // Gen7 v1.1, v1.2
|
||||
#define BOARD_GEN7_13 12 // Gen7 v1.3
|
||||
#define BOARD_GEN7_14 13 // Gen7 v1.4
|
||||
#define BOARD_CHEAPTRONIC 2 // Cheaptronic v1.0
|
||||
#define BOARD_SETHI 20 // Sethi 3D_1
|
||||
#define BOARD_RAMPS_OLD 3 // MEGA/RAMPS up to 1.2
|
||||
#define BOARD_RAMPS_13_EFB 33 // RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Bed)
|
||||
#define BOARD_RAMPS_13_EEB 34 // RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Bed)
|
||||
#define BOARD_RAMPS_13_EFF 35 // RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Fan)
|
||||
#define BOARD_RAMPS_13_EEF 36 // RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Fan)
|
||||
#define BOARD_DUEMILANOVE_328P 4 // Duemilanove w/ ATMega328P pin assignment
|
||||
#define BOARD_GEN6 5 // Gen6
|
||||
#define BOARD_GEN6_DELUXE 51 // Gen6 deluxe
|
||||
#define BOARD_SANGUINOLOLU_11 6 // Sanguinololu < 1.2
|
||||
#define BOARD_SANGUINOLOLU_12 62 // Sanguinololu 1.2 and above
|
||||
#define BOARD_MELZI 63 // Melzi
|
||||
#define BOARD_STB_11 64 // STB V1.1
|
||||
#define BOARD_AZTEEG_X1 65 // Azteeg X1
|
||||
#define BOARD_MELZI_1284 66 // Melzi with ATmega1284 (MaKr3d version)
|
||||
#define BOARD_AZTEEG_X3 67 // Azteeg X3
|
||||
#define BOARD_AZTEEG_X3_PRO 68 // Azteeg X3 Pro
|
||||
#define BOARD_ULTIMAKER 7 // Ultimaker
|
||||
#define BOARD_ULTIMAKER_OLD 71 // Ultimaker (Older electronics. Pre 1.5.4. This is rare)
|
||||
#define BOARD_ULTIMAIN_2 72 // Ultimainboard 2.x (Uses TEMP_SENSOR 20)
|
||||
#define BOARD_3DRAG 77 // 3Drag Controller
|
||||
#define BOARD_TEENSYLU 8 // Teensylu
|
||||
#define BOARD_RUMBA 80 // Rumba
|
||||
#define BOARD_PRINTRBOARD 81 // Printrboard (AT90USB1286)
|
||||
#define BOARD_BRAINWAVE 82 // Brainwave (AT90USB646)
|
||||
#define BOARD_SAV_MKI 83 // SAV Mk-I (AT90USB1286)
|
||||
#define BOARD_TEENSY2 84 // Teensy++2.0 (AT90USB1286) - CLI compile: DEFINES=AT90USBxx_TEENSYPP_ASSIGNMENTS HARDWARE_MOTHERBOARD=84 make
|
||||
#define BOARD_GEN3_PLUS 9 // Gen3+
|
||||
#define BOARD_GEN3_MONOLITHIC 22 // Gen3 Monolithic Electronics
|
||||
#define BOARD_MEGATRONICS 70 // Megatronics
|
||||
#define BOARD_MEGATRONICS_2 701 // Megatronics v2.0
|
||||
#define BOARD_MEGATRONICS_1 702 // Minitronics v1.0
|
||||
#define BOARD_OMCA_A 90 // Alpha OMCA board
|
||||
#define BOARD_OMCA 91 // Final OMCA board
|
||||
#define BOARD_RAMBO 301 // Rambo
|
||||
#define BOARD_ELEFU_3 21 // Elefu Ra Board (v3)
|
||||
#define BOARD_5DPRINT 88 // 5DPrint D8 Driver Board
|
||||
#define BOARD_LEAPFROG 999 // Leapfrog
|
||||
|
||||
#define BOARD_99 99 // This is in pins.h but...?
|
||||
|
||||
#define MB(board) (MOTHERBOARD==BOARD_##board)
|
||||
#define IS_RAMPS (MB(RAMPS_OLD) || MB(RAMPS_13_EFB) || MB(RAMPS_13_EEB) || MB(RAMPS_13_EFF) || MB(RAMPS_13_EEF))
|
||||
|
||||
#endif //__BOARDS_H
|
||||
|
|
@ -6,7 +6,7 @@
|
|||
#include "Wire.h"
|
||||
|
||||
// Settings for the I2C based DIGIPOT (MCP4451) on Azteeg X3 Pro
|
||||
#if MOTHERBOARD == 88
|
||||
#if MB(5DPRINT)
|
||||
#define DIGIPOT_I2C_FACTOR 117.96
|
||||
#define DIGIPOT_I2C_MAX_CURRENT 1.736
|
||||
#else
|
||||
|
|
|
|||
|
|
@ -1,6 +1,8 @@
|
|||
#ifndef CONFIGURATION_H
|
||||
#define CONFIGURATION_H
|
||||
|
||||
#include "boards.h"
|
||||
|
||||
// This configuration file contains the basic settings.
|
||||
// Advanced settings can be found in Configuration_adv.h
|
||||
// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
|
||||
|
|
@ -55,52 +57,10 @@
|
|||
// This enables the serial port associated to the Bluetooth interface
|
||||
//#define BTENABLED // Enable BT interface on AT90USB devices
|
||||
|
||||
|
||||
//// The following define selects which electronics board you have. Please choose the one that matches your setup
|
||||
// 10 = Gen7 custom (Alfons3 Version) "https://github.com/Alfons3/Generation_7_Electronics"
|
||||
// 11 = Gen7 v1.1, v1.2 = 11
|
||||
// 12 = Gen7 v1.3
|
||||
// 13 = Gen7 v1.4
|
||||
// 131 = OpenHardware.co.za custom Gen7 electronics
|
||||
// 2 = Cheaptronic v1.0
|
||||
// 20 = Sethi 3D_1
|
||||
// 3 = MEGA/RAMPS up to 1.2 = 3
|
||||
// 33 = RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Bed)
|
||||
// 34 = RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Bed)
|
||||
// 35 = RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Fan)
|
||||
// 4 = Duemilanove w/ ATMega328P pin assignment
|
||||
// 5 = Gen6
|
||||
// 51 = Gen6 deluxe
|
||||
// 6 = Sanguinololu < 1.2
|
||||
// 62 = Sanguinololu 1.2 and above
|
||||
// 63 = Melzi
|
||||
// 64 = STB V1.1
|
||||
// 65 = Azteeg X1
|
||||
// 66 = Melzi with ATmega1284 (MaKr3d version)
|
||||
// 67 = Azteeg X3
|
||||
// 68 = Azteeg X3 Pro
|
||||
// 7 = Ultimaker
|
||||
// 71 = Ultimaker (Older electronics. Pre 1.5.4. This is rare)
|
||||
// 72 = Ultimainboard 2.x (Uses TEMP_SENSOR 20)
|
||||
// 77 = 3Drag Controller
|
||||
// 8 = Teensylu
|
||||
// 80 = Rumba
|
||||
// 81 = Printrboard (AT90USB1286)
|
||||
// 82 = Brainwave (AT90USB646)
|
||||
// 83 = SAV Mk-I (AT90USB1286)
|
||||
// 84 = Teensy++2.0 (AT90USB1286) // CLI compile: DEFINES=AT90USBxx_TEENSYPP_ASSIGNMENTS HARDWARE_MOTHERBOARD=84 make
|
||||
// 9 = Gen3+
|
||||
// 70 = Megatronics
|
||||
// 701= Megatronics v2.0
|
||||
// 702= Minitronics v1.0
|
||||
// 90 = Alpha OMCA board
|
||||
// 91 = Final OMCA board
|
||||
// 301= Rambo
|
||||
// 21 = Elefu Ra Board (v3)
|
||||
// 88 = 5DPrint D8 Driver Board
|
||||
|
||||
// The following define selects which electronics board you have.
|
||||
// Please choose the name from boards.h that matches your setup
|
||||
#ifndef MOTHERBOARD
|
||||
#define MOTHERBOARD 33
|
||||
#define MOTHERBOARD BOARD_RAMPS_13_EFB
|
||||
#endif
|
||||
|
||||
// Define this to set a custom name for your generic Mendel,
|
||||
|
|
|
|||
|
|
@ -1,6 +1,8 @@
|
|||
#ifndef CONFIGURATION_H
|
||||
#define CONFIGURATION_H
|
||||
|
||||
#include "boards.h"
|
||||
|
||||
// This configuration file contains the basic settings.
|
||||
// Advanced settings can be found in Configuration_adv.h
|
||||
// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
|
||||
|
|
@ -29,53 +31,10 @@
|
|||
// This enables the serial port associated to the Bluetooth interface
|
||||
//#define BTENABLED // Enable BT interface on AT90USB devices
|
||||
|
||||
|
||||
//// The following define selects which electronics board you have. Please choose the one that matches your setup
|
||||
// 10 = Gen7 custom (Alfons3 Version) "https://github.com/Alfons3/Generation_7_Electronics"
|
||||
// 11 = Gen7 v1.1, v1.2 = 11
|
||||
// 12 = Gen7 v1.3
|
||||
// 13 = Gen7 v1.4
|
||||
// 2 = Cheaptronic v1.0
|
||||
// 20 = Sethi 3D_1
|
||||
// 3 = MEGA/RAMPS up to 1.2 = 3
|
||||
// 33 = RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Bed)
|
||||
// 34 = RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Bed)
|
||||
// 35 = RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Fan)
|
||||
// 36 = RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Fan)
|
||||
// 4 = Duemilanove w/ ATMega328P pin assignment
|
||||
// 5 = Gen6
|
||||
// 51 = Gen6 deluxe
|
||||
// 6 = Sanguinololu < 1.2
|
||||
// 62 = Sanguinololu 1.2 and above
|
||||
// 63 = Melzi
|
||||
// 64 = STB V1.1
|
||||
// 65 = Azteeg X1
|
||||
// 66 = Melzi with ATmega1284 (MaKr3d version)
|
||||
// 67 = Azteeg X3
|
||||
// 68 = Azteeg X3 Pro
|
||||
// 7 = Ultimaker
|
||||
// 71 = Ultimaker (Older electronics. Pre 1.5.4. This is rare)
|
||||
// 72 = Ultimainboard 2.x (Uses TEMP_SENSOR 20)
|
||||
// 77 = 3Drag Controller
|
||||
// 8 = Teensylu
|
||||
// 80 = Rumba
|
||||
// 81 = Printrboard (AT90USB1286)
|
||||
// 82 = Brainwave (AT90USB646)
|
||||
// 83 = SAV Mk-I (AT90USB1286)
|
||||
// 84 = Teensy++2.0 (AT90USB1286) // CLI compile: DEFINES=AT90USBxx_TEENSYPP_ASSIGNMENTS HARDWARE_MOTHERBOARD=84 make
|
||||
// 9 = Gen3+
|
||||
// 70 = Megatronics
|
||||
// 701= Megatronics v2.0
|
||||
// 702= Minitronics v1.0
|
||||
// 90 = Alpha OMCA board
|
||||
// 91 = Final OMCA board
|
||||
// 301= Rambo
|
||||
// 21 = Elefu Ra Board (v3)
|
||||
// 88 = 5DPrint D8 Driver Board
|
||||
// 999 = Leapfrog
|
||||
|
||||
// The following define selects which electronics board you have.
|
||||
// Please choose the name from boards.h that matches your setup
|
||||
#ifndef MOTHERBOARD
|
||||
#define MOTHERBOARD 33
|
||||
#define MOTHERBOARD BOARD_RAMPS_13_EFB
|
||||
#endif
|
||||
|
||||
// Define this to set a custom name for your generic Mendel,
|
||||
|
|
|
|||
|
|
@ -1,6 +1,8 @@
|
|||
#ifndef CONFIGURATION_H
|
||||
#define CONFIGURATION_H
|
||||
|
||||
#include "boards.h"
|
||||
|
||||
// This configuration file contains the basic settings.
|
||||
// Advanced settings can be found in Configuration_adv.h
|
||||
// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
|
||||
|
|
@ -30,50 +32,10 @@
|
|||
// This enables the serial port associated to the Bluetooth interface
|
||||
//#define BTENABLED // Enable BT interface on AT90USB devices
|
||||
|
||||
|
||||
//// The following define selects which electronics board you have. Please choose the one that matches your setup
|
||||
// 10 = Gen7 custom (Alfons3 Version) "https://github.com/Alfons3/Generation_7_Electronics"
|
||||
// 11 = Gen7 v1.1, v1.2 = 11
|
||||
// 12 = Gen7 v1.3
|
||||
// 13 = Gen7 v1.4
|
||||
// 2 = Cheaptronic v1.0
|
||||
// 20 = Sethi 3D_1
|
||||
// 3 = MEGA/RAMPS up to 1.2 = 3
|
||||
// 33 = RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Bed)
|
||||
// 34 = RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Bed)
|
||||
// 35 = RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Fan)
|
||||
// 4 = Duemilanove w/ ATMega328P pin assignment
|
||||
// 5 = Gen6
|
||||
// 51 = Gen6 deluxe
|
||||
// 6 = Sanguinololu < 1.2
|
||||
// 62 = Sanguinololu 1.2 and above
|
||||
// 63 = Melzi
|
||||
// 64 = STB V1.1
|
||||
// 65 = Azteeg X1
|
||||
// 66 = Melzi with ATmega1284 (MaKr3d version)
|
||||
// 67 = Azteeg X3
|
||||
// 68 = Azteeg X3 Pro
|
||||
// 7 = Ultimaker
|
||||
// 71 = Ultimaker (Older electronics. Pre 1.5.4. This is rare)
|
||||
// 72 = Ultimainboard 2.x (Uses TEMP_SENSOR 20)
|
||||
// 77 = 3Drag Controller
|
||||
// 8 = Teensylu
|
||||
// 80 = Rumba
|
||||
// 81 = Printrboard (AT90USB1286)
|
||||
// 82 = Brainwave (AT90USB646)
|
||||
// 83 = SAV Mk-I (AT90USB1286)
|
||||
// 9 = Gen3+
|
||||
// 70 = Megatronics
|
||||
// 701= Megatronics v2.0
|
||||
// 702= Minitronics v1.0
|
||||
// 90 = Alpha OMCA board
|
||||
// 91 = Final OMCA board
|
||||
// 301= Rambo
|
||||
// 21 = Elefu Ra Board (v3)
|
||||
// 88 = 5DPrint D8 Driver Board
|
||||
|
||||
// The following define selects which electronics board you have.
|
||||
// Please choose the name from boards.h that matches your setup
|
||||
#ifndef MOTHERBOARD
|
||||
#define MOTHERBOARD 88
|
||||
#define MOTHERBOARD BOARD_5DPRINT
|
||||
#endif
|
||||
|
||||
// Define this to set a custom name for your generic Mendel,
|
||||
|
|
|
|||
|
|
@ -1,6 +1,8 @@
|
|||
#ifndef CONFIGURATION_H
|
||||
#define CONFIGURATION_H
|
||||
|
||||
#include "boards.h"
|
||||
|
||||
// This configuration file contains the basic settings.
|
||||
// Advanced settings can be found in Configuration_adv.h
|
||||
// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
|
||||
|
|
@ -36,53 +38,10 @@
|
|||
// This enables the serial port associated to the Bluetooth interface
|
||||
//#define BTENABLED // Enable BT interface on AT90USB devices
|
||||
|
||||
|
||||
//// The following define selects which electronics board you have. Please choose the one that matches your setup
|
||||
// 10 = Gen7 custom (Alfons3 Version) "https://github.com/Alfons3/Generation_7_Electronics"
|
||||
// 11 = Gen7 v1.1, v1.2 = 11
|
||||
// 12 = Gen7 v1.3
|
||||
// 13 = Gen7 v1.4
|
||||
// 2 = Cheaptronic v1.0
|
||||
// 20 = Sethi 3D_1
|
||||
// 3 = MEGA/RAMPS up to 1.2 = 3
|
||||
// 33 = RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Bed)
|
||||
// 34 = RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Bed)
|
||||
// 35 = RAMPS 1.3 / 1.4 (Power outputs: Extruder, Fan, Fan)
|
||||
// 36 = RAMPS 1.3 / 1.4 (Power outputs: Extruder0, Extruder1, Fan)
|
||||
// 4 = Duemilanove w/ ATMega328P pin assignment
|
||||
// 5 = Gen6
|
||||
// 51 = Gen6 deluxe
|
||||
// 6 = Sanguinololu < 1.2
|
||||
// 62 = Sanguinololu 1.2 and above
|
||||
// 63 = Melzi
|
||||
// 64 = STB V1.1
|
||||
// 65 = Azteeg X1
|
||||
// 66 = Melzi with ATmega1284 (MaKr3d version)
|
||||
// 67 = Azteeg X3
|
||||
// 68 = Azteeg X3 Pro
|
||||
// 7 = Ultimaker
|
||||
// 71 = Ultimaker (Older electronics. Pre 1.5.4. This is rare)
|
||||
// 72 = Ultimainboard 2.x (Uses TEMP_SENSOR 20)
|
||||
// 77 = 3Drag Controller
|
||||
// 8 = Teensylu
|
||||
// 80 = Rumba
|
||||
// 81 = Printrboard (AT90USB1286)
|
||||
// 82 = Brainwave (AT90USB646)
|
||||
// 83 = SAV Mk-I (AT90USB1286)
|
||||
// 84 = Teensy++2.0 (AT90USB1286) // CLI compile: DEFINES=AT90USBxx_TEENSYPP_ASSIGNMENTS HARDWARE_MOTHERBOARD=84 make
|
||||
// 9 = Gen3+
|
||||
// 70 = Megatronics
|
||||
// 701= Megatronics v2.0
|
||||
// 702= Minitronics v1.0
|
||||
// 90 = Alpha OMCA board
|
||||
// 91 = Final OMCA board
|
||||
// 301= Rambo
|
||||
// 21 = Elefu Ra Board (v3)
|
||||
// 88 = 5DPrint D8 Driver Board
|
||||
// 999 = Leapfrog
|
||||
|
||||
// The following define selects which electronics board you have.
|
||||
// Please choose the name from boards.h that matches your setup
|
||||
#ifndef MOTHERBOARD
|
||||
#define MOTHERBOARD 91
|
||||
#define MOTHERBOARD BOARD_OMCA
|
||||
#endif
|
||||
|
||||
// Define this to set a custom name for your generic Mendel,
|
||||
|
|
|
|||
|
|
@ -31,16 +31,16 @@
|
|||
|
||||
#define PROTOCOL_VERSION "1.0"
|
||||
|
||||
#if MOTHERBOARD == 7 || MOTHERBOARD == 71 || MOTHERBOARD == 72
|
||||
#if MB(ULTIMAKER)|| MB(ULTIMAKER_OLD)|| MB(ULTIMAIN_2)
|
||||
#define MACHINE_NAME "Ultimaker"
|
||||
#define FIRMWARE_URL "http://firmware.ultimaker.com"
|
||||
#elif MOTHERBOARD == 80
|
||||
#elif MB(RUMBA)
|
||||
#define MACHINE_NAME "Rumba"
|
||||
#define FIRMWARE_URL "https://github.com/ErikZalm/Marlin/"
|
||||
#elif MOTHERBOARD == 77
|
||||
#elif MB(3DRAG)
|
||||
#define MACHINE_NAME "3Drag"
|
||||
#define FIRMWARE_URL "http://3dprint.elettronicain.it/"
|
||||
#elif MOTHERBOARD == 88
|
||||
#elif MB(5DPRINT)
|
||||
#define MACHINE_NAME "Makibox"
|
||||
#define FIRMWARE_URL "https://github.com/ErikZalm/Marlin/"
|
||||
#else
|
||||
|
|
|
|||
253
Marlin/pins.h
253
Marlin/pins.h
|
|
@ -1,7 +1,9 @@
|
|||
#ifndef PINS_H
|
||||
#define PINS_H
|
||||
|
||||
#if MOTHERBOARD != 88
|
||||
#include "boards.h"
|
||||
|
||||
#if !MB(5DPRINT)
|
||||
#define X_MS1_PIN -1
|
||||
#define X_MS2_PIN -1
|
||||
#define Y_MS1_PIN -1
|
||||
|
|
@ -20,7 +22,7 @@
|
|||
* https://bitbucket.org/makible/5dprint-d8-controller-board
|
||||
****************************************************************************************/
|
||||
|
||||
#if MOTHERBOARD == 88
|
||||
#if MB(5DPRINT)
|
||||
|
||||
#define KNOWN_BOARD 1
|
||||
#define AT90USB 1286 // Disable MarlinSerial etc.
|
||||
|
|
@ -92,13 +94,13 @@
|
|||
#define E0_MS1_PIN 5
|
||||
#define E0_MS2_PIN 4
|
||||
|
||||
#endif /* 88 */
|
||||
#endif // 5DPRINT
|
||||
|
||||
/****************************************************************************************
|
||||
* Leapfrog Driver board
|
||||
*
|
||||
****************************************************************************************/
|
||||
#if MOTHERBOARD == 999 // Leapfrog board
|
||||
#if MB(LEAPFROG) // Leapfrog board
|
||||
#define KNOWN_BOARD 1
|
||||
|
||||
#ifndef __AVR_ATmega1280__
|
||||
|
|
@ -162,14 +164,14 @@
|
|||
/* Unused (1) (2) (3) 4 5 6 7 8 9 10 11 12 13 (14) (15) (16) 17 (18) (19) (20) (21) (22) (23) 24 (25) (26) (27) 28 (29) (30) (31) */
|
||||
|
||||
|
||||
#endif
|
||||
#endif // LEAPFROG
|
||||
|
||||
/****************************************************************************************
|
||||
*
|
||||
*
|
||||
****************************************************************************************/
|
||||
|
||||
#if MOTHERBOARD == 99
|
||||
#if MB(99)
|
||||
#define KNOWN_BOARD 1
|
||||
|
||||
#define X_STEP_PIN 2
|
||||
|
|
@ -207,14 +209,14 @@
|
|||
#define HEATER_BED_PIN 4
|
||||
#define TEMP_BED_PIN 10
|
||||
|
||||
#endif /* 99 */
|
||||
#endif // 99
|
||||
|
||||
/****************************************************************************************
|
||||
* Sethi 3D_1 pin assignment - www.sethi3d.com.br
|
||||
*
|
||||
****************************************************************************************/
|
||||
|
||||
#if MOTHERBOARD == 20
|
||||
#if MB(SETHI)
|
||||
#define KNOWN_BOARD
|
||||
|
||||
#if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__) && !defined(__AVR_ATmega1284P__)
|
||||
|
|
@ -285,7 +287,7 @@
|
|||
#define TX_ENABLE_PIN 12
|
||||
#define RX_ENABLE_PIN 13
|
||||
|
||||
#endif
|
||||
#endif // SETHI
|
||||
|
||||
/****************************************************************************************
|
||||
* Gen7 v1.1, v1.2, v1.3 pin assignment
|
||||
|
|
@ -293,12 +295,12 @@
|
|||
****************************************************************************************/
|
||||
|
||||
|
||||
#if MOTHERBOARD == 12
|
||||
#define MOTHERBOARD 11
|
||||
#if MB(GEN7_13)
|
||||
#define MOTHERBOARD BOARD_GEN7_12
|
||||
#define GEN7_VERSION 13 // v1.3
|
||||
#endif
|
||||
|
||||
#if MOTHERBOARD == 11
|
||||
#if MB(GEN7_12)
|
||||
#define KNOWN_BOARD
|
||||
|
||||
#if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__) && !defined(__AVR_ATmega1284P__)
|
||||
|
|
@ -376,11 +378,11 @@
|
|||
*
|
||||
****************************************************************************************/
|
||||
|
||||
#if MOTHERBOARD == 13
|
||||
#if MB(GEN7_14)
|
||||
#define GEN7_VERSION 14 // v1.4
|
||||
#endif
|
||||
|
||||
#if MOTHERBOARD == 13
|
||||
#if MB(GEN7_14)
|
||||
#define KNOWN_BOARD
|
||||
|
||||
#if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__) && !defined(__AVR_ATmega1284P__)
|
||||
|
|
@ -442,22 +444,19 @@
|
|||
#define TX_ENABLE_PIN 12
|
||||
#define RX_ENABLE_PIN 13
|
||||
|
||||
#endif
|
||||
#endif // GEN7
|
||||
|
||||
/*******************************************************************************
|
||||
*********
|
||||
/******************************************************************************
|
||||
* Gen7 Alfons3 pin assignment
|
||||
*
|
||||
********************************************************************************
|
||||
********/
|
||||
******************************************************************************/
|
||||
/* These Pins are assigned for the modified GEN7 Board from Alfons3 Please review the pins and adjust it for your needs*/
|
||||
|
||||
#if MOTHERBOARD == 10
|
||||
#if MB(GEN7_CUSTOM)
|
||||
#define KNOWN_BOARD
|
||||
|
||||
#if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__) && !defined(__AVR_ATmega1284P__)
|
||||
#error Oops! Make sure you have 'Gen7' selected from the 'Tools -> Boards' menu.
|
||||
|
||||
#endif
|
||||
|
||||
//x axis pins
|
||||
|
|
@ -525,13 +524,13 @@
|
|||
#define BTN_EN2 10
|
||||
#define BTN_ENC 12 //the click
|
||||
|
||||
#endif
|
||||
#endif // GEN7_CUSTOM
|
||||
|
||||
/****************************************************************************************
|
||||
* Arduino Mega pin assignment
|
||||
*
|
||||
****************************************************************************************/
|
||||
#if MOTHERBOARD == 3 || MOTHERBOARD == 33 || MOTHERBOARD == 34 || MOTHERBOARD == 35 || MOTHERBOARD == 36 || MOTHERBOARD == 77 || MOTHERBOARD == 67 || MOTHERBOARD == 68
|
||||
#if IS_RAMPS || MB(3DRAG) || MB(AZTEEG_X3) || MB(AZTEEG_X3_PRO)
|
||||
#define KNOWN_BOARD 1
|
||||
|
||||
//////////////////FIX THIS//////////////
|
||||
|
|
@ -547,11 +546,11 @@
|
|||
// #define RAMPS_V_1_0
|
||||
|
||||
|
||||
#if MOTHERBOARD == 33 || MOTHERBOARD == 34 || MOTHERBOARD == 35 || MOTHERBOARD == 36 || MOTHERBOARD == 77 || MOTHERBOARD == 67 || MOTHERBOARD == 68
|
||||
#if (IS_RAMPS && !MB(RAMPS_OLD)) || MB(3DRAG) || MB(AZTEEG_X3) || MB(AZTEEG_X3_PRO)
|
||||
|
||||
#define LARGE_FLASH true
|
||||
|
||||
#if MOTHERBOARD == 77
|
||||
#if MB(3DRAG)
|
||||
#define X_STEP_PIN 54
|
||||
#define X_DIR_PIN 55
|
||||
#define X_ENABLE_PIN 38
|
||||
|
|
@ -628,16 +627,16 @@
|
|||
#define E1_DIR_PIN 34
|
||||
#define E1_ENABLE_PIN 30
|
||||
|
||||
#if MOTHERBOARD == 34 //FMM added for Filament Extruder
|
||||
#if MB(RAMPS_13_EEB) //FMM added for Filament Extruder
|
||||
#ifdef FILAMENT_SENSOR
|
||||
//define analog pin for the filament width sensor input
|
||||
//Use the RAMPS 1.4 Analog input 5 on the AUX2 connector
|
||||
//define analog pin for the filament width sensor input
|
||||
//Use the RAMPS 1.4 Analog input 5 on the AUX2 connector
|
||||
#define FILWIDTH_PIN 5
|
||||
#endif
|
||||
#endif
|
||||
|
||||
|
||||
#if MOTHERBOARD == 68
|
||||
#if MB(AZTEEG_X3_PRO)
|
||||
#define E2_STEP_PIN 23
|
||||
#define E2_DIR_PIN 25
|
||||
#define E2_ENABLE_PIN 40
|
||||
|
|
@ -656,17 +655,17 @@
|
|||
#define LED_PIN 13
|
||||
#endif
|
||||
|
||||
#if MOTHERBOARD == 33 || MOTHERBOARD == 35 || MOTHERBOARD == 67 || MOTHERBOARD == 68
|
||||
#if MB(RAMPS_13_EFB) || MB(RAMPS_13_EFF) || MB(AZTEEG_X3) || MB(AZTEEG_X3_PRO)
|
||||
#define FAN_PIN 9 // (Sprinter config)
|
||||
#else
|
||||
#define FAN_PIN 4 // IO pin. Buffer needed
|
||||
#endif
|
||||
|
||||
#if MOTHERBOARD == 77 || MOTHERBOARD == 36
|
||||
#if MB(3DRAG) || MB(RAMPS_13_EEF)
|
||||
#define FAN_PIN 8
|
||||
#endif
|
||||
|
||||
#if MOTHERBOARD == 35
|
||||
#if MB(RAMPS_13_EFF)
|
||||
#define CONTROLLERFAN_PIN -1 //Pin used for the fan to cool controller
|
||||
#endif
|
||||
|
||||
|
|
@ -678,24 +677,24 @@
|
|||
#define KILL_PIN -1
|
||||
#endif
|
||||
|
||||
#if MOTHERBOARD == 35
|
||||
#if MB(RAMPS_13_EFF)
|
||||
#define HEATER_0_PIN 8
|
||||
#else
|
||||
#define HEATER_0_PIN 10 // EXTRUDER 1
|
||||
#endif
|
||||
|
||||
#if MOTHERBOARD == 33 || MOTHERBOARD == 67
|
||||
#if MB(RAMPS_13_EFB) || MB(AZTEEG_X3)
|
||||
#define HEATER_1_PIN -1
|
||||
#else
|
||||
#define HEATER_1_PIN 9 // EXTRUDER 2 (FAN On Sprinter)
|
||||
#endif
|
||||
|
||||
|
||||
#if MOTHERBOARD == 77
|
||||
#if MB(3DRAG)
|
||||
#define HEATER_0_PIN 10
|
||||
#define HEATER_1_PIN 12
|
||||
#define HEATER_2_PIN 6
|
||||
#elif MOTHERBOARD == 68
|
||||
#elif MB(AZTEEG_X3_PRO)
|
||||
#define HEATER_2_PIN 16
|
||||
#define HEATER_3_PIN 17
|
||||
#define HEATER_4_PIN 4
|
||||
|
|
@ -708,7 +707,7 @@
|
|||
|
||||
#define TEMP_0_PIN 13 // ANALOG NUMBERING
|
||||
#define TEMP_1_PIN 15 // ANALOG NUMBERING
|
||||
#if MOTHERBOARD == 68
|
||||
#if MB(AZTEEG_X3_PRO)
|
||||
#define TEMP_2_PIN 12 // ANALOG NUMBERING
|
||||
#define TEMP_3_PIN 11 // ANALOG NUMBERING
|
||||
#define TEMP_4_PIN 10 // ANALOG NUMBERING
|
||||
|
|
@ -718,10 +717,10 @@
|
|||
#define TEMP_2_PIN -1 // ANALOG NUMBERING
|
||||
#endif
|
||||
|
||||
#if MOTHERBOARD == 35 || MOTHERBOARD == 36
|
||||
#if MB(RAMPS_13_EFF) || MB(RAMPS_13_EEF)
|
||||
#define HEATER_BED_PIN -1 // NO BED
|
||||
#else
|
||||
#if MOTHERBOARD == 77
|
||||
#if MB(3DRAG)
|
||||
#define HEATER_BED_PIN 9 // BED
|
||||
#else
|
||||
#define HEATER_BED_PIN 8 // BED
|
||||
|
|
@ -746,12 +745,12 @@
|
|||
#endif
|
||||
#endif
|
||||
|
||||
#if MOTHERBOARD == 68
|
||||
#if MB(AZTEEG_X3_PRO)
|
||||
#define BEEPER 33
|
||||
#endif
|
||||
|
||||
#ifdef TEMP_STAT_LEDS
|
||||
#if MOTHERBOARD == 67
|
||||
#if MB(AZTEEG_X3)
|
||||
#define STAT_LED_RED 6
|
||||
#define STAT_LED_BLUE 11
|
||||
#endif
|
||||
|
|
@ -814,7 +813,7 @@
|
|||
|
||||
#endif
|
||||
|
||||
#if MOTHERBOARD == 77
|
||||
#if MB(3DRAG)
|
||||
#define BEEPER -1
|
||||
|
||||
#define LCD_PINS_RS 27
|
||||
|
|
@ -832,10 +831,10 @@
|
|||
#endif
|
||||
#else //old style panel with shift register
|
||||
//arduino pin witch triggers an piezzo beeper
|
||||
#define BEEPER 33 //No Beeper added
|
||||
#define BEEPER 33 //No Beeper added
|
||||
|
||||
//buttons are attached to a shift register
|
||||
// Not wired this yet
|
||||
// Not wired this yet
|
||||
//#define SHIFT_CLK 38
|
||||
//#define SHIFT_LD 42
|
||||
//#define SHIFT_OUT 40
|
||||
|
|
@ -850,7 +849,7 @@
|
|||
#endif
|
||||
#endif //ULTRA_LCD
|
||||
|
||||
#else // RAMPS_V_1_1 or RAMPS_V_1_2 as default (MOTHERBOARD == 3)
|
||||
#else // RAMPS_V_1_1 or RAMPS_V_1_2 as default (BOARD_RAMPS_OLD)
|
||||
|
||||
#define X_STEP_PIN 26
|
||||
#define X_DIR_PIN 28
|
||||
|
|
@ -896,7 +895,7 @@
|
|||
#define TEMP_2_PIN -1
|
||||
#define TEMP_BED_PIN 1 // MUST USE ANALOG INPUT NUMBERING NOT DIGITAL OUTPUT NUMBERING!!!!!!!!!
|
||||
|
||||
#endif // MOTHERBOARD == 33 || MOTHERBOARD == 34 || MOTHERBOARD == 35 || MOTHERBOARD == 77
|
||||
#endif // RAMPS_13_EFB || RAMPS_13_EEB || RAMPS_13_EFF || 3DRAG
|
||||
|
||||
// SPI for Max6675 Thermocouple
|
||||
|
||||
|
|
@ -910,13 +909,13 @@
|
|||
#define MAX6675_SS 49
|
||||
#endif
|
||||
|
||||
#endif //MOTHERBOARD == 3 || MOTHERBOARD == 33 || MOTHERBOARD == 34 || MOTHERBOARD == 35 || MOTHERBOARD == 77
|
||||
#endif // RAMPS_OLD || RAMPS_13_EFB || RAMPS_13_EEB || RAMPS_13_EFF || 3DRAG
|
||||
|
||||
/****************************************************************************************
|
||||
* Duemilanove w/ ATMega328P pin assignment
|
||||
*
|
||||
****************************************************************************************/
|
||||
#if MOTHERBOARD == 4
|
||||
#if MB(DUEMILANOVE_328P)
|
||||
#define KNOWN_BOARD 1
|
||||
|
||||
#ifndef __AVR_ATmega328P__
|
||||
|
|
@ -958,25 +957,25 @@
|
|||
#define HEATER_BED_PIN -1
|
||||
#define TEMP_BED_PIN -1
|
||||
|
||||
#endif
|
||||
#endif // DUEMILANOVE_328P
|
||||
|
||||
/****************************************************************************************
|
||||
* Elefu RA Board Pin Assignments
|
||||
*
|
||||
****************************************************************************************/
|
||||
#if MOTHERBOARD == 21
|
||||
#define KNOWN_BOARD 1
|
||||
#if MB(ELEFU_3)
|
||||
#define KNOWN_BOARD 1
|
||||
|
||||
#ifndef __AVR_ATmega2560__
|
||||
#error Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.
|
||||
#endif
|
||||
|
||||
|
||||
#define X_STEP_PIN 49
|
||||
#define X_DIR_PIN 13
|
||||
#define X_ENABLE_PIN 48
|
||||
#define X_MIN_PIN 35
|
||||
#define X_MAX_PIN -1 //34
|
||||
#define X_STEP_PIN 49
|
||||
#define X_DIR_PIN 13
|
||||
#define X_ENABLE_PIN 48
|
||||
#define X_MIN_PIN 35
|
||||
#define X_MAX_PIN -1 //34
|
||||
|
||||
#define Y_STEP_PIN 11
|
||||
#define Y_DIR_PIN 9
|
||||
|
|
@ -1008,18 +1007,18 @@
|
|||
#define FAN_PIN 16 //5V PWM
|
||||
|
||||
#define PS_ON_PIN 10 //Set to -1 if using a manual switch on the PWRSW Connector
|
||||
#define SLEEP_WAKE_PIN 26 //This feature still needs work
|
||||
#define SLEEP_WAKE_PIN 26 //This feature still needs work
|
||||
|
||||
#define HEATER_0_PIN 45 //12V PWM1
|
||||
#define HEATER_1_PIN 46 //12V PWM2
|
||||
#define HEATER_2_PIN 17 //12V PWM3
|
||||
#define HEATER_BED_PIN 44 //DOUBLE 12V PWM
|
||||
#define TEMP_0_PIN 3 //ANALOG NUMBERING
|
||||
#define TEMP_1_PIN 2 //ANALOG NUMBERING
|
||||
#define TEMP_2_PIN 1 //ANALOG NUMBERING
|
||||
#define TEMP_BED_PIN 0 //ANALOG NUMBERING
|
||||
#define HEATER_0_PIN 45 //12V PWM1
|
||||
#define HEATER_1_PIN 46 //12V PWM2
|
||||
#define HEATER_2_PIN 17 //12V PWM3
|
||||
#define HEATER_BED_PIN 44 //DOUBLE 12V PWM
|
||||
#define TEMP_0_PIN 3 //ANALOG NUMBERING
|
||||
#define TEMP_1_PIN 2 //ANALOG NUMBERING
|
||||
#define TEMP_2_PIN 1 //ANALOG NUMBERING
|
||||
#define TEMP_BED_PIN 0 //ANALOG NUMBERING
|
||||
|
||||
#define BEEPER 36
|
||||
#define BEEPER 36
|
||||
|
||||
#define KILL_PIN -1
|
||||
|
||||
|
|
@ -1082,14 +1081,14 @@
|
|||
#endif //RA_LIGHTING
|
||||
|
||||
|
||||
#endif /* Ra Board */
|
||||
#endif // ELEFU_3
|
||||
|
||||
|
||||
/****************************************************************************************
|
||||
* Gen6 pin assignment
|
||||
*
|
||||
****************************************************************************************/
|
||||
#if MOTHERBOARD == 5 || MOTHERBOARD == 51
|
||||
#if MB(GEN6) || MB(GEN6_DELUXE)
|
||||
#define KNOWN_BOARD 1
|
||||
|
||||
#ifndef __AVR_ATmega644P__
|
||||
|
|
@ -1128,7 +1127,7 @@
|
|||
#define HEATER_0_PIN 14 //changed @ rkoeppl 20110410
|
||||
#define HEATER_1_PIN -1
|
||||
#define HEATER_2_PIN -1
|
||||
#if MOTHERBOARD == 5
|
||||
#if MB(GEN6)
|
||||
#define HEATER_BED_PIN -1 //changed @ rkoeppl 20110410
|
||||
#define TEMP_BED_PIN -1 //changed @ rkoeppl 20110410
|
||||
#else
|
||||
|
|
@ -1149,32 +1148,32 @@
|
|||
#define TX_ENABLE_PIN 12
|
||||
#define RX_ENABLE_PIN 13
|
||||
|
||||
|
||||
#endif
|
||||
#endif // GEN6 || GEN6_DELUXE
|
||||
|
||||
/****************************************************************************************
|
||||
* Sanguinololu pin assignment
|
||||
*
|
||||
****************************************************************************************/
|
||||
#if MOTHERBOARD == 64
|
||||
#if MB(STB_11)
|
||||
#define STB
|
||||
#endif
|
||||
#if MOTHERBOARD == 63 || MOTHERBOARD == 66
|
||||
#if MB(MELZI) || MB(MELZI_1284)
|
||||
#define MELZI
|
||||
#endif
|
||||
#if MOTHERBOARD == 65
|
||||
#if MB(AZTEEG_X1)
|
||||
#define AZTEEG_X1
|
||||
#endif
|
||||
#if MOTHERBOARD == 62 || MOTHERBOARD == 63 || MOTHERBOARD == 64 || MOTHERBOARD == 65 || MOTHERBOARD == 66
|
||||
#if MB(SANGUINOLOLU_12) || MB(MELZI) || MB(STB_11) || MB(AZTEEG_X1) || MB(MELZI_1284)
|
||||
#undef MOTHERBOARD
|
||||
#define MOTHERBOARD 6
|
||||
#define MOTHERBOARD BOARD_SANGUINOLOLU_11
|
||||
#define SANGUINOLOLU_V_1_2
|
||||
|
||||
#if defined(__AVR_ATmega1284P__)
|
||||
#define LARGE_FLASH true
|
||||
#define LARGE_FLASH true
|
||||
#endif
|
||||
#endif
|
||||
#if MOTHERBOARD == 6
|
||||
|
||||
#if MB(SANGUINOLOLU_11)
|
||||
#define KNOWN_BOARD 1
|
||||
#ifndef __AVR_ATmega644P__
|
||||
#ifndef __AVR_ATmega1284P__
|
||||
|
|
@ -1211,7 +1210,7 @@
|
|||
|
||||
#ifdef STB
|
||||
#define FAN_PIN 4
|
||||
// Uncomment this if you have the first generation (V1.10) of STBs board
|
||||
// Uncomment this if you have the first generation (V1.10) of STBs board
|
||||
#define LCD_PIN_BL 17 // LCD backlight LED
|
||||
#endif
|
||||
|
||||
|
|
@ -1322,7 +1321,7 @@
|
|||
// Pins for DOGM SPI LCD Support
|
||||
#define DOGLCD_A0 30
|
||||
#define DOGLCD_CS 17
|
||||
#define LCD_PIN_BL 28 // backlight LED on PA3
|
||||
#define LCD_PIN_BL 28 // backlight LED on PA3
|
||||
// GLCD features
|
||||
#define LCD_CONTRAST 1
|
||||
// Uncomment screen orientation
|
||||
|
|
@ -1338,15 +1337,16 @@
|
|||
#define SDCARDDETECT -1
|
||||
#endif //Makrpanel
|
||||
|
||||
#endif
|
||||
#endif // SANGUINOLOLU_11
|
||||
|
||||
|
||||
#if MOTHERBOARD == 7
|
||||
#define KNOWN_BOARD
|
||||
/*****************************************************************
|
||||
* Ultimaker pin assignment
|
||||
******************************************************************/
|
||||
|
||||
#if MB(ULTIMAKER)
|
||||
#define KNOWN_BOARD
|
||||
|
||||
#ifndef __AVR_ATmega1280__
|
||||
#ifndef __AVR_ATmega2560__
|
||||
#error Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu.
|
||||
|
|
@ -1442,9 +1442,9 @@
|
|||
#endif
|
||||
#endif //ULTRA_LCD
|
||||
|
||||
#endif
|
||||
#endif // ULTIMAKER
|
||||
|
||||
#if MOTHERBOARD == 71
|
||||
#if MB(ULTIMAKER_OLD)
|
||||
#define KNOWN_BOARD
|
||||
/*****************************************************************
|
||||
* Ultimaker pin assignment (Old electronics)
|
||||
|
|
@ -1511,9 +1511,9 @@
|
|||
#define LCD_PINS_D6 32
|
||||
#define LCD_PINS_D7 30
|
||||
|
||||
#endif
|
||||
#endif // ULTIMAKER_OLD
|
||||
|
||||
#if MOTHERBOARD == 72
|
||||
#if MB(ULTIMAIN_2)
|
||||
#define KNOWN_BOARD
|
||||
/*****************************************************************
|
||||
* Ultiboard v2.0 pin assignment
|
||||
|
|
@ -1596,13 +1596,13 @@
|
|||
|
||||
#define SDCARDDETECT 39
|
||||
|
||||
#endif//MOTHERBOARD == 72
|
||||
#endif // ULTIMAIN_2
|
||||
|
||||
/****************************************************************************************
|
||||
* RUMBA pin assignment
|
||||
*
|
||||
****************************************************************************************/
|
||||
#if MOTHERBOARD == 80
|
||||
#if MB(RUMBA)
|
||||
#define KNOWN_BOARD 1
|
||||
|
||||
#ifndef __AVR_ATmega2560__
|
||||
|
|
@ -1712,7 +1712,7 @@
|
|||
#define BTN_EN2 12
|
||||
#define BTN_ENC 43
|
||||
|
||||
#endif //MOTHERBOARD==80
|
||||
#endif // RUMBA
|
||||
|
||||
|
||||
/****************************************************************************************
|
||||
|
|
@ -1721,7 +1721,7 @@
|
|||
http://www.pjrc.com/teensy/teensyduino.html
|
||||
* See http://reprap.org/wiki/Printrboard for more info
|
||||
****************************************************************************************/
|
||||
#if MOTHERBOARD == 8 || MOTHERBOARD == 81
|
||||
#if MB(TEENSYLU) || MB(PRINTRBOARD)
|
||||
#define KNOWN_BOARD 1
|
||||
#define AT90USB 1286 // Disable MarlinSerial etc.
|
||||
|
||||
|
|
@ -1759,7 +1759,7 @@
|
|||
// You may need to change FAN_PIN to 16 because Marlin isn't using fastio.h
|
||||
// for the fan and Teensyduino uses a different pin mapping.
|
||||
|
||||
#if MOTHERBOARD == 8 // Teensylu
|
||||
#if MB(TEENSYLU) // Teensylu
|
||||
#define X_STOP_PIN 13
|
||||
#define Y_STOP_PIN 14
|
||||
#define Z_STOP_PIN 15
|
||||
|
|
@ -1793,14 +1793,14 @@
|
|||
#define MOSI_PIN 10
|
||||
#endif
|
||||
|
||||
#endif // MOTHERBOARD == 8 (Teensylu) or 81 (Printrboard)
|
||||
#endif // TEENSYLU || PRINTRBOARD
|
||||
|
||||
/****************************************************************************************
|
||||
* Brainwave 1.0 pin assignments (AT90USB646)
|
||||
* Requires hardware bundle for Arduino:
|
||||
https://github.com/unrepentantgeek/brainwave-arduino
|
||||
****************************************************************************************/
|
||||
#if MOTHERBOARD == 82
|
||||
#if MB(BRAINWAVE)
|
||||
#define KNOWN_BOARD 1
|
||||
#define AT90USB 646 // Disable MarlinSerial etc.
|
||||
|
||||
|
|
@ -1856,7 +1856,7 @@
|
|||
#define MOSI_PIN 10
|
||||
#endif
|
||||
|
||||
#endif // MOTHERBOARD == 82 (Brainwave)
|
||||
#endif // BRAINWAVE
|
||||
|
||||
//
|
||||
// SAV Mk-I
|
||||
|
|
@ -1867,7 +1867,7 @@
|
|||
http://www.pjrc.com/teensy/teensyduino.html
|
||||
RepRap Clone Wars project board.
|
||||
****************************************************************************************/
|
||||
#if MOTHERBOARD == 83 // SAV Mk-I
|
||||
#if MB(SAV_MKI) // SAV Mk-I
|
||||
#define KNOWN_BOARD 1
|
||||
#define AT90USB 1286 // Disable MarlinSerial etc.
|
||||
|
||||
|
|
@ -1941,7 +1941,7 @@
|
|||
#define SR_DATA_PIN 0
|
||||
#define SR_CLK_PIN 1
|
||||
|
||||
#endif // MOTHERBOARD == 83
|
||||
#endif // SAV_MKI
|
||||
|
||||
/****************************************************************************************
|
||||
* Teensy++ 2.0 Breadboard pin assignments (AT90USB1286)
|
||||
|
|
@ -1951,7 +1951,7 @@
|
|||
* CLI build: DEFINES=AT90USBxx_TEENSYPP_ASSIGNMENTS HARDWARE_MOTHERBOARD=84 make
|
||||
*
|
||||
****************************************************************************************/
|
||||
#if MOTHERBOARD == 84
|
||||
#if MB(TEENSY2)
|
||||
#define KNOWN_BOARD 1
|
||||
#define AT90USB 1286 // Disable MarlinSerial etc.
|
||||
|
||||
|
|
@ -2036,7 +2036,7 @@ DaveX plan for Teensylu/printrboard-type pinouts (ref teensylu & sprinter) for a
|
|||
#define TEMP_2_PIN -1
|
||||
|
||||
#define SDPOWER -1
|
||||
#define SDCARDDETECT -1
|
||||
#define SDCARDDETECT -1
|
||||
#define SDSS 20 // 8
|
||||
#define LED_PIN 6
|
||||
#define PS_ON_PIN 27
|
||||
|
|
@ -2062,15 +2062,15 @@ DaveX plan for Teensylu/printrboard-type pinouts (ref teensylu & sprinter) for a
|
|||
#define BTN_ENC 40
|
||||
#endif
|
||||
|
||||
#endif // MOTHERBOARD == 84 (Teensy++2.0 Breadboard)
|
||||
#endif // TEENSY2
|
||||
|
||||
|
||||
/****************************************************************************************
|
||||
* Gen3+ pin assignment
|
||||
*
|
||||
****************************************************************************************/
|
||||
#if MOTHERBOARD == 9
|
||||
#define MOTHERBOARD 6 /*TODO: Figure out, Why is this done?*/
|
||||
#if MB(GEN3_PLUS)
|
||||
#define MOTHERBOARD BOARD_SANGUINOLOLU_11 /*TODO: Figure out, Why is this done?*/
|
||||
#define KNOWN_BOARD 1
|
||||
#ifndef __AVR_ATmega644P__
|
||||
#ifndef __AVR_ATmega1284P__
|
||||
|
|
@ -2116,13 +2116,13 @@ DaveX plan for Teensylu/printrboard-type pinouts (ref teensylu & sprinter) for a
|
|||
#define SDSS 4
|
||||
#define HEATER_2_PIN -1
|
||||
|
||||
#endif
|
||||
#endif // GEN3_PLUS
|
||||
|
||||
/****************************************************************************************
|
||||
* Gen3 Monolithic Electronics
|
||||
*
|
||||
****************************************************************************************/
|
||||
#if MOTHERBOARD == 22
|
||||
#if MB(GEN3_MONOLITHIC)
|
||||
#define KNOWN_BOARD 1
|
||||
|
||||
#ifndef __AVR_ATmega644P__
|
||||
|
|
@ -2170,12 +2170,12 @@ DaveX plan for Teensylu/printrboard-type pinouts (ref teensylu & sprinter) for a
|
|||
#define TEMP_BED_PIN -1
|
||||
|
||||
|
||||
#define SDSS -1
|
||||
#define SDSS -1
|
||||
#define SDPOWER -1
|
||||
#define LED_PIN -1
|
||||
|
||||
//pin for controlling the PSU.
|
||||
#define PS_ON_PIN 14 //Alex, Do this work on the card?
|
||||
#define PS_ON_PIN 14 //Alex, Do this work on the card?
|
||||
|
||||
//Alex extras from Gen3+
|
||||
#define KILL_PIN -1
|
||||
|
|
@ -2183,7 +2183,7 @@ DaveX plan for Teensylu/printrboard-type pinouts (ref teensylu & sprinter) for a
|
|||
#define TEMP_2_PIN -1
|
||||
#define HEATER_2_PIN -1
|
||||
|
||||
#endif
|
||||
#endif // GEN3_MONOLITHIC
|
||||
|
||||
/****************************************************************************************
|
||||
* Open Motion controller with enable based extruders
|
||||
|
|
@ -2214,7 +2214,7 @@ DaveX plan for Teensylu/printrboard-type pinouts (ref teensylu & sprinter) for a
|
|||
* +--------+
|
||||
*
|
||||
****************************************************************************************/
|
||||
#if MOTHERBOARD == 90 //Alpha OMCA board
|
||||
#if MB(OMCA_A) //Alpha OMCA board
|
||||
#define KNOWN_BOARD 1
|
||||
|
||||
#ifndef __AVR_ATmega644__
|
||||
|
|
@ -2266,9 +2266,9 @@ DaveX plan for Teensylu/printrboard-type pinouts (ref teensylu & sprinter) for a
|
|||
#define TEMP_BED_PIN -1 // 1,2 or I2C
|
||||
/* Unused (1) (2) (3) 4 5 6 7 8 9 10 11 12 13 (14) (15) (16) 17 (18) (19) (20) (21) (22) (23) 24 (25) (26) (27) 28 (29) (30) (31) */
|
||||
|
||||
#endif
|
||||
#endif // OMCA_A
|
||||
|
||||
#if MOTHERBOARD == 91 // Final OMCA board -- REF http://sanguino.cc/hardware
|
||||
#if MB(OMCA) // Final OMCA board -- REF http://sanguino.cc/hardware
|
||||
#define KNOWN_BOARD 1
|
||||
|
||||
#if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__)
|
||||
|
|
@ -2332,14 +2332,13 @@ DaveX plan for Teensylu/printrboard-type pinouts (ref teensylu & sprinter) for a
|
|||
#define I2C_SCL 16
|
||||
#define I2C_SDA 17
|
||||
|
||||
#endif
|
||||
#endif // OMCA
|
||||
|
||||
#if MOTHERBOARD == 301
|
||||
#define KNOWN_BOARD
|
||||
/*****************************************************************
|
||||
* Rambo Pin Assignments
|
||||
******************************************************************/
|
||||
|
||||
#if MB(RAMBO)
|
||||
#define KNOWN_BOARD
|
||||
#ifndef __AVR_ATmega2560__
|
||||
#error Oops! Make sure you have 'Arduino Mega 2560' selected from the 'Tools -> Boards' menu.
|
||||
#endif
|
||||
|
|
@ -2478,13 +2477,13 @@ DaveX plan for Teensylu/printrboard-type pinouts (ref teensylu & sprinter) for a
|
|||
#define FILWIDTH_PIN 3
|
||||
#endif //FILAMENT_SENSOR
|
||||
|
||||
#endif
|
||||
#endif // RAMBO
|
||||
|
||||
/****************************************************************************************
|
||||
* MegaTronics
|
||||
*
|
||||
****************************************************************************************/
|
||||
#if MOTHERBOARD == 70
|
||||
#if MB(MEGATRONICS)
|
||||
#define KNOWN_BOARD 1
|
||||
|
||||
|
||||
|
|
@ -2570,7 +2569,7 @@ DaveX plan for Teensylu/printrboard-type pinouts (ref teensylu & sprinter) for a
|
|||
#define BLEN_B 1
|
||||
#define BLEN_A 0
|
||||
|
||||
#define SDCARDDETECT -1 // Ramps does not use this port
|
||||
#define SDCARDDETECT -1 // Ramps does not use this port
|
||||
|
||||
//encoder rotation values
|
||||
#define encrot0 0
|
||||
|
|
@ -2580,13 +2579,13 @@ DaveX plan for Teensylu/printrboard-type pinouts (ref teensylu & sprinter) for a
|
|||
#endif
|
||||
#endif //ULTRA_LCD
|
||||
|
||||
#endif
|
||||
#endif // MEGATRONICS
|
||||
|
||||
/****************************************************************************************
|
||||
* MegaTronics v2.0
|
||||
*
|
||||
****************************************************************************************/
|
||||
#if MOTHERBOARD == 701
|
||||
#if MB(MEGATRONICS_2)
|
||||
#define KNOWN_BOARD 1
|
||||
|
||||
|
||||
|
|
@ -2682,7 +2681,7 @@ DaveX plan for Teensylu/printrboard-type pinouts (ref teensylu & sprinter) for a
|
|||
#define BLEN_B 1
|
||||
#define BLEN_A 0
|
||||
|
||||
#define SDCARDDETECT -1 // Megatronics does not use this port
|
||||
#define SDCARDDETECT -1 // Megatronics does not use this port
|
||||
|
||||
//encoder rotation values
|
||||
#define encrot0 0
|
||||
|
|
@ -2690,14 +2689,14 @@ DaveX plan for Teensylu/printrboard-type pinouts (ref teensylu & sprinter) for a
|
|||
#define encrot2 3
|
||||
#define encrot3 1
|
||||
|
||||
#endif
|
||||
#endif // MEGATRONICS_2
|
||||
|
||||
|
||||
/****************************************************************************************
|
||||
* Minitronics v1.0
|
||||
*
|
||||
****************************************************************************************/
|
||||
#if MOTHERBOARD == 702
|
||||
#if MB(MEGATRONICS_1)
|
||||
#define KNOWN_BOARD 1
|
||||
|
||||
|
||||
|
|
@ -2778,7 +2777,7 @@ DaveX plan for Teensylu/printrboard-type pinouts (ref teensylu & sprinter) for a
|
|||
#define BLEN_B 1
|
||||
#define BLEN_A 0
|
||||
|
||||
#define SDCARDDETECT -1 // Megatronics does not use this port
|
||||
#define SDCARDDETECT -1 // Megatronics does not use this port
|
||||
|
||||
//encoder rotation values
|
||||
#define encrot0 0
|
||||
|
|
@ -2786,13 +2785,13 @@ DaveX plan for Teensylu/printrboard-type pinouts (ref teensylu & sprinter) for a
|
|||
#define encrot2 3
|
||||
#define encrot3 1
|
||||
|
||||
#endif
|
||||
#endif // MEGATRONICS_1
|
||||
|
||||
/****************************************************************************************
|
||||
* Cheaptronic v1.0
|
||||
*
|
||||
****************************************************************************************/
|
||||
#if MOTHERBOARD == 2
|
||||
#if MB(CHEAPTRONIC)
|
||||
#define KNOWN_BOARD 1
|
||||
|
||||
#ifndef __AVR_ATmega2560__
|
||||
|
|
@ -2887,7 +2886,7 @@ DaveX plan for Teensylu/printrboard-type pinouts (ref teensylu & sprinter) for a
|
|||
#define encrot2 3
|
||||
#define encrot3 1
|
||||
|
||||
#endif
|
||||
#endif // CHEAPTRONIC
|
||||
|
||||
|
||||
|
||||
|
|
@ -2954,5 +2953,5 @@ DaveX plan for Teensylu/printrboard-type pinouts (ref teensylu & sprinter) for a
|
|||
HEATER_BED_PIN, FAN_PIN, \
|
||||
_E0_PINS _E1_PINS _E2_PINS \
|
||||
analogInputToDigitalPin(TEMP_0_PIN), analogInputToDigitalPin(TEMP_1_PIN), analogInputToDigitalPin(TEMP_2_PIN), analogInputToDigitalPin(TEMP_BED_PIN) }
|
||||
#endif
|
||||
|
||||
#endif //__PINS_H
|
||||
|
|
|
|||
|
|
@ -768,7 +768,7 @@ return(filament_width_nominal/temp*100);
|
|||
|
||||
void tp_init()
|
||||
{
|
||||
#if (MOTHERBOARD == 80) && ((TEMP_SENSOR_0==-1)||(TEMP_SENSOR_1==-1)||(TEMP_SENSOR_2==-1)||(TEMP_SENSOR_BED==-1))
|
||||
#if MB(RUMBA) && ((TEMP_SENSOR_0==-1)||(TEMP_SENSOR_1==-1)||(TEMP_SENSOR_2==-1)||(TEMP_SENSOR_BED==-1))
|
||||
//disable RUMBA JTAG in case the thermocouple extension is plugged on top of JTAG connector
|
||||
MCUCR=(1<<JTD);
|
||||
MCUCR=(1<<JTD);
|
||||
|
|
|
|||
Loading…
Reference in a new issue