zaubentrucker/muele-marlin
1
0
Fork 0
Code Issues Pull requests Actions Packages Projects Releases Wiki Activity

Level Corners with Probe option (#20241)

Browse source
This commit is contained in:
wmariz 2020-11-26 10:58:19 -03:00 committed by Scott Lahteine
parent 7c9c897dac
commit 747bde7e64
11 changed files with 211 additions and 69 deletions
Show stats Download patch file Download diff file Expand all files Collapse all files

6
Marlin/Configuration.h
View file

@ -1392,6 +1392,12 @@
#define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points
#define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
//#define LEVEL_CORNERS_USE_PROBE
#if ENABLED(LEVEL_CORNERS_USE_PROBE)
#define LEVEL_CORNERS_PROBE_TOLERANCE 0.1
#define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify
//#define LEVEL_CORNERS_AUDIO_FEEDBACK
#endif
#endif
/**

10
Marlin/src/feature/backlash.cpp
View file

@ -123,24 +123,22 @@ void Backlash::add_correction_steps(const int32_t &da, const int32_t &db, const
}
#if ENABLED(MEASURE_BACKLASH_WHEN_PROBING)
#if HAS_CUSTOM_PROBE_PIN
#define TEST_PROBE_PIN (READ(Z_MIN_PROBE_PIN) != Z_MIN_PROBE_ENDSTOP_INVERTING)
#else
#define TEST_PROBE_PIN (READ(Z_MIN_PIN) != Z_MIN_ENDSTOP_INVERTING)
#endif
#include "../module/probe.h"
// Measure Z backlash by raising nozzle in increments until probe deactivates
void Backlash::measure_with_probe() {
if (measured_count.z == 255) return;
const float start_height = current_position.z;
while (current_position.z < (start_height + BACKLASH_MEASUREMENT_LIMIT) && TEST_PROBE_PIN)
while (current_position.z < (start_height + BACKLASH_MEASUREMENT_LIMIT) && PROBE_TRIGGERED())
do_blocking_move_to_z(current_position.z + BACKLASH_MEASUREMENT_RESOLUTION, MMM_TO_MMS(BACKLASH_MEASUREMENT_FEEDRATE));
// The backlash from all probe points is averaged, so count the number of measurements
measured_mm.z += current_position.z - start_height;
measured_count.z++;
}
#endif
#endif // BACKLASH_COMPENSATION

11
Marlin/src/feature/bltouch.cpp
View file

@ -31,6 +31,7 @@ BLTouch bltouch;
bool BLTouch::last_written_mode; // Initialized by settings.load, 0 = Open Drain; 1 = 5V Drain
#include "../module/servo.h"
#include "../module/probe.h"
void stop();
@ -90,15 +91,7 @@ void BLTouch::clear() {
_stow(); // STOW to be ready for meaningful work. Could fail, don't care
}
bool BLTouch::triggered() {
return (
#if ENABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN)
READ(Z_MIN_PIN) != Z_MIN_ENDSTOP_INVERTING
#else
READ(Z_MIN_PROBE_PIN) != Z_MIN_PROBE_ENDSTOP_INVERTING
#endif
);
}
bool BLTouch::triggered() { return PROBE_TRIGGERED(); }
bool BLTouch::deploy_proc() {
// Do a DEPLOY

8
Marlin/src/gcode/calibrate/G425.cpp
View file

@ -143,14 +143,16 @@ inline void park_above_object(measurements_t &m, const float uncertainty) {
#endif
#if !PIN_EXISTS(CALIBRATION)
#include "../../module/probe.h"
#endif
inline bool read_calibration_pin() {
return (
#if PIN_EXISTS(CALIBRATION)
READ(CALIBRATION_PIN) != CALIBRATION_PIN_INVERTING
#elif HAS_CUSTOM_PROBE_PIN
READ(Z_MIN_PROBE_PIN) != Z_MIN_PROBE_ENDSTOP_INVERTING
#else
READ(Z_MIN_PIN) != Z_MIN_ENDSTOP_INVERTING
PROBE_TRIGGERED()
#endif
);
}

4
Marlin/src/inc/SanityCheck.h
View file

@ -357,6 +357,8 @@
#error "LEVEL_CORNERS_INSET is now LEVEL_CORNERS_INSET_LFRB."
#elif ENABLED(LEVEL_BED_CORNERS) && !defined(LEVEL_CORNERS_INSET_LFRB)
#error "LEVEL_BED_CORNERS requires LEVEL_CORNERS_INSET_LFRB values."
#elif BOTH(LEVEL_CORNERS_USE_PROBE, SENSORLESS_PROBING)
#error "LEVEL_CORNERS_USE_PROBE is incompatible with SENSORLESS_PROBING."
#elif defined(BEZIER_JERK_CONTROL)
#error "BEZIER_JERK_CONTROL is now S_CURVE_ACCELERATION."
#elif HAS_JUNCTION_DEVIATION && defined(JUNCTION_DEVIATION_FACTOR)
@ -1603,7 +1605,7 @@ static_assert(hbm[Z_AXIS] >= 0, "HOMING_BUMP_MM.Z must be greater than or equal
* Allen Key
* Deploying the Allen Key probe uses big moves in z direction. Too dangerous for an unhomed z-axis.
*/
#if ENABLED(Z_PROBE_ALLEN_KEY) && (Z_HOME_DIR < 0) && ENABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN)
#if BOTH(Z_PROBE_ALLEN_KEY, Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN) && (Z_HOME_DIR < 0)
#error "You can't home to a Z min endstop with a Z_PROBE_ALLEN_KEY."
#endif

3
Marlin/src/lcd/language/language_en.h
View file

@ -125,6 +125,8 @@ namespace Language_en {
PROGMEM Language_Str MSG_BED_LEVELING = _UxGT("Bed Leveling");
PROGMEM Language_Str MSG_LEVEL_BED = _UxGT("Level Bed");
PROGMEM Language_Str MSG_LEVEL_CORNERS = _UxGT("Level Corners");
PROGMEM Language_Str MSG_LEVEL_CORNERS_RAISE = _UxGT("Raise Bed Until Probe Triggered");
PROGMEM Language_Str MSG_LEVEL_CORNERS_IN_RANGE = _UxGT("All Corners Within Tolerance. Level Bed");
PROGMEM Language_Str MSG_NEXT_CORNER = _UxGT("Next Corner");
PROGMEM Language_Str MSG_MESH_EDITOR = _UxGT("Mesh Editor");
PROGMEM Language_Str MSG_EDIT_MESH = _UxGT("Edit Mesh");
@ -379,6 +381,7 @@ namespace Language_en {
PROGMEM Language_Str MSG_BUTTON_DONE = _UxGT("Done");
PROGMEM Language_Str MSG_BUTTON_BACK = _UxGT("Back");
PROGMEM Language_Str MSG_BUTTON_PROCEED = _UxGT("Proceed");
PROGMEM Language_Str MSG_BUTTON_SKIP = _UxGT("Skip");
PROGMEM Language_Str MSG_PAUSING = _UxGT("Pausing...");
PROGMEM Language_Str MSG_PAUSE_PRINT = _UxGT("Pause Print");
PROGMEM Language_Str MSG_RESUME_PRINT = _UxGT("Resume Print");

205
Marlin/src/lcd/menu/menu_bed_corners.cpp
View file

@ -44,53 +44,187 @@
#define LEVEL_CORNERS_HEIGHT 0.0
#endif
#if ENABLED(LEVEL_CORNERS_USE_PROBE)
#include "../../module/probe.h"
#include "../../module/endstops.h"
#if ENABLED(BLTOUCH)
#include "../../feature/bltouch.h"
#endif
#ifndef LEVEL_CORNERS_PROBE_TOLERANCE
#define LEVEL_CORNERS_PROBE_TOLERANCE 0.1
#endif
#if ENABLED(LEVEL_CORNERS_AUDIO_FEEDBACK)
#include "../../libs/buzzer.h"
#define PROBE_BUZZ() BUZZ(200, 600)
#else
#define PROBE_BUZZ() NOOP
#endif
static float last_z;
static bool corner_probing_done;
static bool verify_corner;
static int good_points;
#endif
static_assert(LEVEL_CORNERS_Z_HOP >= 0, "LEVEL_CORNERS_Z_HOP must be >= 0. Please update your configuration.");
extern const char G28_STR[];
#if HAS_LEVELING
static bool leveling_was_active = false;
#endif
static int8_t bed_corner;
/**
* Level corners, starting in the front-left corner.
*/
static int8_t bed_corner;
static inline void _lcd_goto_next_corner() {
constexpr float lfrb[4] = LEVEL_CORNERS_INSET_LFRB;
constexpr xy_pos_t lf { (X_MIN_BED) + lfrb[0], (Y_MIN_BED) + lfrb[1] },
rb { (X_MAX_BED) - lfrb[2], (Y_MAX_BED) - lfrb[3] };
line_to_z(LEVEL_CORNERS_Z_HOP);
switch (bed_corner) {
case 0: current_position = lf; break; // copy xy
case 1: current_position.x = rb.x; break;
case 2: current_position.y = rb.y; break;
case 3: current_position.x = lf.x; break;
#if ENABLED(LEVEL_CENTER_TOO)
case 4: current_position.set(X_CENTER, Y_CENTER); break;
#if ENABLED(LEVEL_CORNERS_USE_PROBE)
static inline void _lcd_level_bed_corners_probing() {
ui.goto_screen([]{ MenuItem_static::draw((LCD_HEIGHT - 1) / 2, GET_TEXT(MSG_PROBING_MESH)); });
float lfrb[4] = LEVEL_CORNERS_INSET_LFRB;
xy_pos_t lf { (X_MIN_BED) + lfrb[0] - probe.offset_xy.x , (Y_MIN_BED) + lfrb[1] - probe.offset_xy.y },
rb { (X_MAX_BED) - lfrb[2] - probe.offset_xy.x , (Y_MAX_BED) - lfrb[3] - probe.offset_xy.y };
do_blocking_move_to_z(LEVEL_CORNERS_Z_HOP - probe.offset.z);
switch (bed_corner) {
case 0: current_position = lf; break; // copy xy
case 1: current_position.x = rb.x; break;
case 2: current_position.y = rb.y; break;
case 3: current_position.x = lf.x; break;
#if ENABLED(LEVEL_CENTER_TOO)
case 4: current_position.set(X_CENTER - probe.offset_xy.x, Y_CENTER - probe.offset_xy.y); good_points--; break;
#endif
}
do_blocking_move_to_xy(current_position);
#if ENABLED(BLTOUCH) && DISABLED(BLTOUCH_HS_MODE)
bltouch.deploy(); // DEPLOY in LOW SPEED MODE on every probe action
#endif
TERN_(QUIET_PROBING, probe.set_probing_paused(true));
// Move down until the probe is triggered
do_blocking_move_to_z(last_z - (LEVEL_CORNERS_PROBE_TOLERANCE), manual_feedrate_mm_s.z);
// Check to see if the probe was triggered
bool probe_triggered = TEST(endstops.trigger_state(), TERN(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN, Z_MIN, Z_MIN_PROBE));
if (!probe_triggered) {
static bool wait_for_probe;
ui.goto_screen([]{
MenuItem_confirm::select_screen(
GET_TEXT(MSG_BUTTON_DONE), GET_TEXT(MSG_BUTTON_SKIP)
, []{ corner_probing_done = true;
wait_for_probe = false;
TERN_(HAS_LEVELING, set_bed_leveling_enabled(leveling_was_active));
ui.goto_previous_screen_no_defer();
}
, []{ wait_for_probe = false; }
, GET_TEXT(MSG_LEVEL_CORNERS_RAISE)
, (const char*)nullptr, PSTR("")
);
});
ui.set_selection(true);
wait_for_probe = true;
while (wait_for_probe && !probe_triggered) {
probe_triggered = PROBE_TRIGGERED();
if (probe_triggered) PROBE_BUZZ();
idle();
}
wait_for_probe = false;
TERN_(LEVEL_CORNERS_VERIFY_RAISED, verify_corner = true);
}
TERN_(QUIET_PROBING, probe.set_probing_paused(false));
#if ENABLED(BLTOUCH) && DISABLED(BLTOUCH_HS_MODE)
bltouch.stow();
#endif
if (probe_triggered) {
endstops.hit_on_purpose();
if (!WITHIN(current_position.z, last_z - (LEVEL_CORNERS_PROBE_TOLERANCE), last_z + (LEVEL_CORNERS_PROBE_TOLERANCE))) {
last_z = current_position.z;
good_points = 0;
}
if (!verify_corner) good_points++;
}
if (!corner_probing_done) {
if (!verify_corner) bed_corner++;
if (bed_corner > 3) bed_corner = 0;
verify_corner = false;
if (good_points < 4)
_lcd_level_bed_corners_probing();
else {
ui.goto_screen([]{
MenuItem_confirm::confirm_screen(
[]{ ui.goto_previous_screen_no_defer();
queue.inject_P(TERN(HAS_LEVELING, PSTR("G28\nG29"), G28_STR));
}
, []{ ui.goto_previous_screen_no_defer(); }
, GET_TEXT(MSG_LEVEL_CORNERS_IN_RANGE)
, (const char*)nullptr, PSTR("?")
);
});
ui.set_selection(true);
}
}
}
line_to_current_position(manual_feedrate_mm_s.x);
line_to_z(LEVEL_CORNERS_HEIGHT);
if (++bed_corner > 3 + ENABLED(LEVEL_CENTER_TOO)) bed_corner = 0;
}
#else
static inline void _lcd_goto_next_corner() {
constexpr float lfrb[4] = LEVEL_CORNERS_INSET_LFRB;
constexpr xy_pos_t lf { (X_MIN_BED) + lfrb[0], (Y_MIN_BED) + lfrb[1] },
rb { (X_MAX_BED) - lfrb[2], (Y_MAX_BED) - lfrb[3] };
line_to_z(LEVEL_CORNERS_Z_HOP);
switch (bed_corner) {
case 0: current_position = lf; break; // copy xy
case 1: current_position.x = rb.x; break;
case 2: current_position.y = rb.y; break;
case 3: current_position.x = lf.x; break;
#if ENABLED(LEVEL_CENTER_TOO)
case 4: current_position.set(X_CENTER, Y_CENTER); break;
#endif
}
line_to_current_position(manual_feedrate_mm_s.x);
line_to_z(LEVEL_CORNERS_HEIGHT);
if (++bed_corner > 3 + ENABLED(LEVEL_CENTER_TOO)) bed_corner = 0;
}
#endif
static inline void _lcd_level_bed_corners_homing() {
_lcd_draw_homing();
if (all_axes_homed()) {
bed_corner = 0;
ui.goto_screen([]{
MenuItem_confirm::select_screen(
GET_TEXT(MSG_BUTTON_NEXT), GET_TEXT(MSG_BUTTON_DONE)
, _lcd_goto_next_corner
, []{
TERN_(HAS_LEVELING, set_bed_leveling_enabled(leveling_was_active));
ui.goto_previous_screen_no_defer();
}
, GET_TEXT(TERN(LEVEL_CENTER_TOO, MSG_LEVEL_BED_NEXT_POINT, MSG_NEXT_CORNER))
, (const char*)nullptr, PSTR("?")
);
});
ui.set_selection(true);
_lcd_goto_next_corner();
#if ENABLED(LEVEL_CORNERS_USE_PROBE)
TERN_(LEVEL_CENTER_TOO, bed_corner = 4);
endstops.enable_z_probe(true);
ui.goto_screen(_lcd_level_bed_corners_probing);
#else
bed_corner = 0;
ui.goto_screen([]{
MenuItem_confirm::select_screen(
GET_TEXT(MSG_BUTTON_NEXT), GET_TEXT(MSG_BUTTON_DONE)
, _lcd_goto_next_corner
, []{
TERN_(HAS_LEVELING, set_bed_leveling_enabled(leveling_was_active));
ui.goto_previous_screen_no_defer();
}
, GET_TEXT(TERN(LEVEL_CENTER_TOO, MSG_LEVEL_BED_NEXT_POINT, MSG_NEXT_CORNER))
, (const char*)nullptr, PSTR("?")
);
});
ui.set_selection(true);
_lcd_goto_next_corner();
#endif
}
}
@ -107,6 +241,13 @@ void _lcd_level_bed_corners() {
set_bed_leveling_enabled(false);
#endif
#if ENABLED(LEVEL_CORNERS_USE_PROBE)
last_z = LEVEL_CORNERS_HEIGHT;
corner_probing_done = false;
verify_corner = false;
good_points = 0;
#endif
ui.goto_screen(_lcd_level_bed_corners_homing);
}

6
Marlin/src/module/endstops.cpp
View file

@ -48,6 +48,10 @@
#include "../feature/joystick.h"
#endif
#if HAS_BED_PROBE
#include "probe.h"
#endif
Endstops endstops;
// private:
@ -455,7 +459,7 @@ void _O2 Endstops::report_states() {
ES_REPORT(Z4_MAX);
#endif
#if HAS_CUSTOM_PROBE_PIN
print_es_state(READ(Z_MIN_PROBE_PIN) != Z_MIN_PROBE_ENDSTOP_INVERTING, PSTR(STR_Z_PROBE));
print_es_state(PROBE_TRIGGERED(), PSTR(STR_Z_PROBE));
#endif
#if HAS_FILAMENT_SENSOR
#if NUM_RUNOUT_SENSORS == 1

20
Marlin/src/module/probe.cpp
View file

@ -270,13 +270,7 @@ FORCE_INLINE void probe_specific_action(const bool deploy) {
#if ENABLED(PAUSE_BEFORE_DEPLOY_STOW)
do {
#if ENABLED(PAUSE_PROBE_DEPLOY_WHEN_TRIGGERED)
if (deploy == (
#if HAS_CUSTOM_PROBE_PIN
READ(Z_MIN_PROBE_PIN) == Z_MIN_PROBE_ENDSTOP_INVERTING
#else
READ(Z_MIN_PIN) == Z_MIN_ENDSTOP_INVERTING
#endif
)) break;
if (deploy == PROBE_TRIGGERED()) break;
#endif
BUZZ(100, 659);
@ -375,23 +369,15 @@ bool Probe::set_deployed(const bool deploy) {
const xy_pos_t old_xy = current_position;
#if ENABLED(PROBE_TRIGGERED_WHEN_STOWED_TEST)
#if HAS_CUSTOM_PROBE_PIN
#define PROBE_STOWED() (READ(Z_MIN_PROBE_PIN) != Z_MIN_PROBE_ENDSTOP_INVERTING)
#else
#define PROBE_STOWED() (READ(Z_MIN_PIN) != Z_MIN_ENDSTOP_INVERTING)
#endif
#endif
#ifdef PROBE_STOWED
// Only deploy/stow if needed
if (PROBE_STOWED() == deploy) {
if (PROBE_TRIGGERED() == deploy) {
if (!deploy) endstops.enable_z_probe(false); // Switch off triggered when stowed probes early
// otherwise an Allen-Key probe can't be stowed.
probe_specific_action(deploy);
}
if (PROBE_STOWED() == deploy) { // Unchanged after deploy/stow action?
if (PROBE_TRIGGERED() == deploy) { // Unchanged after deploy/stow action?
if (IsRunning()) {
SERIAL_ERROR_MSG("Z-Probe failed");
LCD_ALERTMESSAGEPGM_P(PSTR("Err: ZPROBE"));

6
Marlin/src/module/probe.h
View file

@ -38,6 +38,12 @@
};
#endif
#if HAS_CUSTOM_PROBE_PIN
#define PROBE_TRIGGERED() (READ(Z_MIN_PROBE_PIN) != Z_MIN_PROBE_ENDSTOP_INVERTING)
#else
#define PROBE_TRIGGERED() (READ(Z_MIN_PIN) != Z_MIN_ENDSTOP_INVERTING)
#endif
class Probe {
public:

1
buildroot/tests/LPC1769-tests
View file

@ -19,6 +19,7 @@ opt_set TEMP_SENSOR_1 -1
opt_set TEMP_SENSOR_BED 5
opt_enable VIKI2 SDSUPPORT ADAPTIVE_FAN_SLOWING NO_FAN_SLOWING_IN_PID_TUNING \
FIX_MOUNTED_PROBE AUTO_BED_LEVELING_BILINEAR G29_RETRY_AND_RECOVER Z_MIN_PROBE_REPEATABILITY_TEST DEBUG_LEVELING_FEATURE \
LEVEL_BED_CORNERS LEVEL_CORNERS_USE_PROBE LEVEL_CORNERS_VERIFY_RAISED \
BABYSTEPPING BABYSTEP_XY BABYSTEP_ZPROBE_OFFSET BABYSTEP_ZPROBE_GFX_OVERLAY \
PRINTCOUNTER NOZZLE_PARK_FEATURE NOZZLE_CLEAN_FEATURE SLOW_PWM_HEATERS PIDTEMPBED EEPROM_SETTINGS INCH_MODE_SUPPORT TEMPERATURE_UNITS_SUPPORT \
Z_SAFE_HOMING ADVANCED_PAUSE_FEATURE PARK_HEAD_ON_PAUSE \