✨ Creality CR-10 SmartPro (#24151)

Co-authored-by: Scott Lahteine <github@thinkyhead.com>

Marlin/src/core/boards.h

@@ -352,19 +352,20 @@
 #define BOARD_CREALITY_V431_D         4049  // Creality v4.3.1d (STM32F103RC / STM32F103RE)
 #define BOARD_CREALITY_V452           4050  // Creality v4.5.2 (STM32F103RC / STM32F103RE)
 #define BOARD_CREALITY_V453           4051  // Creality v4.5.3 (STM32F103RC / STM32F103RE)
-#define BOARD_CREALITY_V24S1          4052  // Creality v2.4.S1 (STM32F103RC / STM32F103RE) v101 as found in the Ender 7
+#define BOARD_CREALITY_V24S1          4052  // Creality v2.4.S1 (STM32F103RC / STM32F103RE) v101 as found in the Ender-7
-#define BOARD_CREALITY_V24S1_301      4053  // Creality v2.4.S1_301 (STM32F103RC / STM32F103RE) as found in the Ender 3 S1
+#define BOARD_CREALITY_V24S1_301      4053  // Creality v2.4.S1_301 (STM32F103RC / STM32F103RE) v301 as found in the Ender-3 S1
-#define BOARD_TRIGORILLA_PRO          4054  // Trigorilla Pro (STM32F103ZE)
+#define BOARD_CREALITY_V25S1          4054  // Creality v2.5.S1 (STM32F103RE) as found in the CR-10 Smart Pro
-#define BOARD_FLY_MINI                4055  // FLYmaker FLY MINI (STM32F103RC)
+#define BOARD_TRIGORILLA_PRO          4055  // Trigorilla Pro (STM32F103ZE)
-#define BOARD_FLSUN_HISPEED           4056  // FLSUN HiSpeedV1 (STM32F103VE)
+#define BOARD_FLY_MINI                4056  // FLYmaker FLY MINI (STM32F103RC)
-#define BOARD_BEAST                   4057  // STM32F103RE Libmaple-based controller
+#define BOARD_FLSUN_HISPEED           4057  // FLSUN HiSpeedV1 (STM32F103VE)
-#define BOARD_MINGDA_MPX_ARM_MINI     4058  // STM32F103ZE Mingda MD-16
+#define BOARD_BEAST                   4058  // STM32F103RE Libmaple-based controller
-#define BOARD_GTM32_PRO_VD            4059  // STM32F103VE controller
+#define BOARD_MINGDA_MPX_ARM_MINI     4059  // STM32F103ZE Mingda MD-16
-#define BOARD_ZONESTAR_ZM3E2          4060  // Zonestar ZM3E2    (STM32F103RC)
+#define BOARD_GTM32_PRO_VD            4060  // STM32F103VE controller
-#define BOARD_ZONESTAR_ZM3E4          4061  // Zonestar ZM3E4 V1 (STM32F103VC)
+#define BOARD_ZONESTAR_ZM3E2          4061  // Zonestar ZM3E2    (STM32F103RC)
-#define BOARD_ZONESTAR_ZM3E4V2        4062  // Zonestar ZM3E4 V2 (STM32F103VC)
+#define BOARD_ZONESTAR_ZM3E4          4062  // Zonestar ZM3E4 V1 (STM32F103VC)
-#define BOARD_ERYONE_ERY32_MINI       4063  // Eryone Ery32 mini (STM32F103VE)
+#define BOARD_ZONESTAR_ZM3E4V2        4063  // Zonestar ZM3E4 V2 (STM32F103VC)
-#define BOARD_PANDA_PI_V29            4064  // Panda Pi V2.9 - Standalone (STM32F103RC)
+#define BOARD_ERYONE_ERY32_MINI       4064  // Eryone Ery32 mini (STM32F103VE)
+#define BOARD_PANDA_PI_V29            4065  // Panda Pi V2.9 - Standalone (STM32F103RC)
 
 //
 // ARM Cortex-M4F

Marlin/src/pins/pins.h

@@ -583,6 +583,8 @@
   #include "stm32f1/pins_CREALITY_V24S1.h"      // STM32F1                                env:STM32F103RE_creality env:STM32F103RE_creality_xfer env:STM32F103RC_creality env:STM32F103RC_creality_xfer env:STM32F103RE_creality_maple
 #elif MB(CREALITY_V24S1_301)
   #include "stm32f1/pins_CREALITY_V24S1_301.h"  // STM32F1                                env:STM32F103RE_creality env:STM32F103RE_creality_xfer env:STM32F103RC_creality env:STM32F103RC_creality_xfer env:STM32F103RE_creality_maple
+#elif MB(CREALITY_V25S1)
+  #include "stm32f1/pins_CREALITY_V25S1.h"      // STM32F1                                env:STM32F103RE_creality_smartPro env:STM32F103RE_creality_smartPro_maple
 #elif MB(TRIGORILLA_PRO)
   #include "stm32f1/pins_TRIGORILLA_PRO.h"      // STM32F1                                env:trigorilla_pro env:trigorilla_pro_maple
 #elif MB(FLY_MINI)

Marlin/src/pins/stm32f1/pins_CREALITY_V24S1.h

@@ -22,7 +22,7 @@
 #pragma once
 
 /**
- * Creality v2.4.S1 (STM32F103RE / STM32F103RC) v101 as found in the Ender 7 board pin assignments
+ * Creality v2.4.S1 (STM32F103RE / STM32F103RC) v101 as found in the Ender 7
  */
 
 #define BOARD_INFO_NAME      "Creality v2.4.S1 V101"

Marlin/src/pins/stm32f1/pins_CREALITY_V25S1.h

@@ -0,0 +1,152 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (c) 2022 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
+ *
+ */
+#pragma once
+
+/**
+ * Creality v2.5.S1 (STM32F103RE / STM32F103RC) as found in the CR-10 Smart Pro
+ */
+
+#include "env_validate.h"
+
+#if HAS_MULTI_HOTEND || E_STEPPERS > 1
+  #error "Creality V2.5.S1 only supports one hotend / E-stepper. Comment out this line to continue."
+#endif
+
+#define BOARD_INFO_NAME      "Creality v2.5.S1"
+#define DEFAULT_MACHINE_NAME "Creality3D"
+
+//
+// Release PB4 (Y_ENABLE_PIN) from JTAG NRST role
+//
+#define DISABLE_DEBUG
+
+//
+// EEPROM
+//
+#if NO_EEPROM_SELECTED
+  #define IIC_BL24CXX_EEPROM                      // EEPROM on I2C-0
+  //#define SDCARD_EEPROM_EMULATION
+  //#define FLASH_EEPROM_EMULATION
+#endif
+
+#if ENABLED(IIC_BL24CXX_EEPROM)
+  #define IIC_EEPROM_SDA                  PA11
+  #define IIC_EEPROM_SCL                  PA12
+  #define MARLIN_EEPROM_SIZE             0x800  // 2K (24C16)
+#elif EITHER(SDCARD_EEPROM_EMULATION, FLASH_EEPROM_EMULATION)
+  #define MARLIN_EEPROM_SIZE             0x800  // 2K
+#endif
+
+//
+// Limit Switches
+//
+#define X_STOP_PIN                          PC4
+#define Y_STOP_PIN                          PC5
+
+#if ENABLED(BLTOUCH)
+  #define Z_STOP_PIN                        -1
+  #define SERVO0_PIN                        PC14  // BLTouch OUT PIN
+  #ifndef Z_MIN_PROBE_PIN
+    #define Z_MIN_PROBE_PIN                 PC15  // BLTouch IN PIN
+  #endif
+#else
+  #define Z_STOP_PIN                        PC15
+  #if ENABLED(PROBE_ACTIVATION_SWITCH)
+    #define PROBE_TARE_PIN                  PC14
+    #define PROBE_ACTIVATION_SWITCH_PIN     PB2
+  #endif
+#endif
+
+//
+// Filament Runout Sensor
+//
+#if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define FIL_RUNOUT_PIN                    PA15  // "Pulled-high"
+#endif
+
+//
+// Steppers
+//
+#define X_STEP_PIN                          PB8
+#define X_DIR_PIN                           PB7
+#define X_ENABLE_PIN                        PC3
+
+#define Y_STEP_PIN                          PB6
+#define Y_DIR_PIN                           PB5
+#define Y_ENABLE_PIN                X_ENABLE_PIN
+
+#define Z_STEP_PIN                          PB4
+#define Z_DIR_PIN                           PB3
+#define Z_ENABLE_PIN                X_ENABLE_PIN
+
+#define E0_STEP_PIN                         PC2
+#define E0_DIR_PIN                          PB9
+#define E0_ENABLE_PIN               X_ENABLE_PIN
+
+//
+// Temperature Sensors
+//
+#define TEMP_0_PIN                          PB1   // TH1
+#define TEMP_BED_PIN                        PB0   // TB1
+
+//
+// Heaters / Fans
+//
+#define HEATER_0_PIN                        PB14  // HEATER1
+#define HEATER_BED_PIN                      PB13  // HOT BED
+
+#define FAN_PIN                             PB15  // FAN
+#ifndef E0_AUTO_FAN_PIN
+  #define E0_AUTO_FAN_PIN                   PC13  // FAN
+#endif
+#define FAN_SOFT_PWM_REQUIRED
+
+//
+// SD Card
+//
+#define SD_DETECT_PIN                       PC7
+#define SDCARD_CONNECTION                ONBOARD
+#define ON_BOARD_SPI_DEVICE                    1
+#define ONBOARD_SD_CS_PIN                   PC12  // SDSS
+#define SDIO_SUPPORT
+#define NO_SD_HOST_DRIVE                          // This board's SD is only seen by the printer
+
+//
+// Misc. Functions
+//
+#define CASE_LIGHT_PIN                      PA7
+
+//
+// Suicide Power
+//
+#define PS_ON_PIN                           PA0
+#define MOTOR_CIRCUIT_PIN                   PA1
+
+//
+// Motor Protect
+//
+#define MOTOR_PROTECT_PIN                   PC0
+
+//
+// WiFi Reset
+//
+#define RESET_WIFI_PIN                      PB12

Marlin/src/pins/stm32f1/pins_CREALITY_V4.h

@@ -40,6 +40,11 @@
 
 #define BOARD_NO_NATIVE_USB
 
+//
+// Release PB4 (Y_ENABLE_PIN) from JTAG NRST role
+//
+#define DISABLE_DEBUG
+
 //
 // EEPROM
 //
@@ -122,11 +127,6 @@
 #endif
 #define E0_ENABLE_PIN               X_ENABLE_PIN
 
-//
-// Release PB4 (Y_ENABLE_PIN) from JTAG NRST role
-//
-#define DISABLE_DEBUG
-
 //
 // Temperature Sensors
 //

Marlin/src/pins/stm32f1/pins_CREALITY_V4210.h

@@ -40,34 +40,24 @@
 
 #define BOARD_NO_NATIVE_USB
 
+//
+// Release PB4 (Y_ENABLE_PIN) from JTAG NRST role
+//
+#define DISABLE_DEBUG
+
 //
 // EEPROM
 //
 #if NO_EEPROM_SELECTED
-  // FLASH
+  #define IIC_BL24CXX_EEPROM                      // EEPROM on I2C-0
-  //#define FLASH_EEPROM_EMULATION
+#endif
-
+#if ENABLED(IIC_BL24CXX_EEPROM)
-  // I2C
-  #define IIC_BL24CXX_EEPROM                      // EEPROM on I2C-0 used only for display settings
-  #if ENABLED(IIC_BL24CXX_EEPROM)
   #define IIC_EEPROM_SDA                    PA11
   #define IIC_EEPROM_SCL                    PA12
   #define MARLIN_EEPROM_SIZE               0x800  // 2K (24C16)
-  #else
+#else
   #define SDCARD_EEPROM_EMULATION                 // SD EEPROM until all EEPROM is BL24CXX
   #define MARLIN_EEPROM_SIZE               0x800  // 2K
-  #endif
-
-  // SPI
-  //#define SPI_EEPROM                            // EEPROM on SPI-0
-  //#define SPI_CHAN_EEPROM1  ?
-  //#define SPI_EEPROM1_CS_PIN    ?
-
-  // 2K EEPROM
-  //#define SPI_EEPROM2_CS_PIN    ?
-
-  // 32Mb FLASH
-  //#define SPI_FLASH_CS_PIN  ?
 #endif
 
 //
@@ -82,7 +72,9 @@
 #define Y_STOP_PIN                          PA7
 #define Z_STOP_PIN                          PA5
 
-#define Z_MIN_PROBE_PIN                     PA5   // BLTouch IN
+#ifndef Z_MIN_PROBE_PIN
+  #define Z_MIN_PROBE_PIN                   PA5   // BLTouch IN
+#endif
 
 //
 // Filament Runout Sensor
@@ -94,42 +86,37 @@
 //
 // Steppers
 //
-#define X_ENABLE_PIN                        PC3
 #ifndef X_STEP_PIN
   #define X_STEP_PIN                        PC2
 #endif
 #ifndef X_DIR_PIN
   #define X_DIR_PIN                         PB9
 #endif
+#define X_ENABLE_PIN                        PC3
 
-#define Y_ENABLE_PIN                        PC3
 #ifndef Y_STEP_PIN
   #define Y_STEP_PIN                        PB8
 #endif
 #ifndef Y_DIR_PIN
   #define Y_DIR_PIN                         PB7
 #endif
+#define Y_ENABLE_PIN                X_ENABLE_PIN
 
-#define Z_ENABLE_PIN                        PC3
 #ifndef Z_STEP_PIN
   #define Z_STEP_PIN                        PB6
 #endif
 #ifndef Z_DIR_PIN
   #define Z_DIR_PIN                         PB5
 #endif
+#define Z_ENABLE_PIN                X_ENABLE_PIN
 
-#define E0_ENABLE_PIN                       PC3
 #ifndef E0_STEP_PIN
   #define E0_STEP_PIN                       PB4
 #endif
 #ifndef E0_DIR_PIN
   #define E0_DIR_PIN                        PB3
 #endif
-
+#define E0_ENABLE_PIN               X_ENABLE_PIN
-//
-// Release PB4 (Y_ENABLE_PIN) from JTAG NRST role
-//
-#define DISABLE_DEBUG
 
 //
 // Temperature Sensors

buildroot/share/PlatformIO/ldscripts/crealityPro.ld

@@ -0,0 +1,14 @@
+MEMORY
+{
+  ram (rwx) : ORIGIN = 0x20000000, LENGTH = 64K - 40
+  rom (rx)  : ORIGIN = 0x08010000, LENGTH = 512K - 64K
+}
+
+/* Provide memory region aliases for common.inc */
+REGION_ALIAS("REGION_TEXT", rom);
+REGION_ALIAS("REGION_DATA", ram);
+REGION_ALIAS("REGION_BSS", ram);
+REGION_ALIAS("REGION_RODATA", rom);
+
+/* Let common.inc handle the real work. */
+INCLUDE common.inc

ini/stm32f1-maple.ini

@@ -147,6 +147,14 @@ extra_scripts        = ${common_stm32f1.extra_scripts}
 debug_tool           = jlink
 upload_protocol      = jlink
 
+#
+# Creality (STM32F103RET6)
+#
+[env:STM32F103RE_creality_smartPro_maple]
+extends              = env:STM32F103RE_creality_maple
+board_build.address  = 0x08010000
+board_build.ldscript = crealityPro.ld
+
 #
 # BigTree SKR Mini E3 V2.0 & DIP / SKR CR6 (STM32F103RET6 ARM Cortex-M3)
 #

ini/stm32f1.ini

@@ -153,6 +153,11 @@ board   = genericSTM32F103RE
 extends = STM32F103Rx_creality_xfer
 board   = genericSTM32F103RE
 
+[env:STM32F103RE_creality_smartPro]
+extends                     = STM32F103Rx_creality
+board_build.offset          = 0x10000
+board_upload.offset_address = 0x08010000
+
 #
 # Creality 256K (STM32F103RC)
 #