🔧 HAS_CUSTOM_PROBE_PIN => USES_Z_MIN_PROBE_PIN

Marlin/src/HAL/LPC1768/inc/SanityCheck.h

@@ -146,7 +146,7 @@ static_assert(DISABLED(BAUD_RATE_GCODE), "BAUD_RATE_GCODE is not yet supported o
     #error "Serial port pins (2) conflict with other pins!"
   #elif Y_HOME_TO_MIN && IS_TX2(Y_STOP_PIN)
     #error "Serial port pins (2) conflict with Y endstop pin!"
-  #elif HAS_CUSTOM_PROBE_PIN && IS_TX2(Z_MIN_PROBE_PIN)
+  #elif USES_Z_MIN_PROBE_PIN && IS_TX2(Z_MIN_PROBE_PIN)
     #error "Serial port pins (2) conflict with probe pin!"
   #elif ANY_TX(2, X_ENABLE_PIN, Y_ENABLE_PIN) || ANY_RX(2, X_DIR_PIN, Y_DIR_PIN)
     #error "Serial port pins (2) conflict with X/Y stepper pins!"
@@ -237,7 +237,7 @@ static_assert(DISABLED(BAUD_RATE_GCODE), "BAUD_RATE_GCODE is not yet supported o
     #define PIN_IS_SCL2(P) (P##_PIN == P0_11)
     #if PIN_IS_SDA2(Y_STOP)
       #error "i2c SDA2 overlaps with Y endstop pin!"
-    #elif HAS_CUSTOM_PROBE_PIN && PIN_IS_SDA2(Z_MIN_PROBE)
+    #elif USES_Z_MIN_PROBE_PIN && PIN_IS_SDA2(Z_MIN_PROBE)
       #error "i2c SDA2 overlaps with Z probe pin!"
     #elif PIN_IS_SDA2(X_ENABLE) || PIN_IS_SDA2(Y_ENABLE)
       #error "i2c SDA2 overlaps with X/Y ENABLE pin!"

Marlin/src/inc/Conditionals_LCD.h

@@ -911,9 +911,9 @@
     #define HAS_PROBE_XY_OFFSET 1
   #endif
   #if DISABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN) && !BOTH(DELTA, SENSORLESS_PROBING)
-    #define HAS_CUSTOM_PROBE_PIN 1
+    #define USES_Z_MIN_PROBE_PIN 1
   #endif
-  #if Z_HOME_TO_MIN && (!HAS_CUSTOM_PROBE_PIN || ENABLED(USE_PROBE_FOR_Z_HOMING))
+  #if Z_HOME_TO_MIN && (!USES_Z_MIN_PROBE_PIN || ENABLED(USE_PROBE_FOR_Z_HOMING))
     #define HOMING_Z_WITH_PROBE 1
   #endif
   #ifndef Z_PROBE_LOW_POINT

Marlin/src/inc/Conditionals_post.h

@@ -2459,7 +2459,7 @@
 //
 
 // Is an endstop plug used for extra Z endstops or the probe?
-#define IS_PROBE_PIN(A,M) (HAS_CUSTOM_PROBE_PIN && Z_MIN_PROBE_PIN == A##_##M##_PIN)
+#define IS_PROBE_PIN(A,M) (USES_Z_MIN_PROBE_PIN && Z_MIN_PROBE_PIN == A##_##M##_PIN)
 #define IS_X2_ENDSTOP(A,M) (ENABLED(X_DUAL_ENDSTOPS) && X2_USE_ENDSTOP == _##A##M##_)
 #define IS_Y2_ENDSTOP(A,M) (ENABLED(Y_DUAL_ENDSTOPS) && Y2_USE_ENDSTOP == _##A##M##_)
 #define IS_Z2_ENDSTOP(A,M) (ENABLED(Z_MULTI_ENDSTOPS) && Z2_USE_ENDSTOP == _##A##M##_)
@@ -2533,7 +2533,7 @@
 #if PIN_EXISTS(Z4_MAX)
   #define HAS_Z4_MAX 1
 #endif
-#if BOTH(HAS_BED_PROBE, HAS_CUSTOM_PROBE_PIN) && PIN_EXISTS(Z_MIN_PROBE)
+#if BOTH(HAS_BED_PROBE, USES_Z_MIN_PROBE_PIN) && PIN_EXISTS(Z_MIN_PROBE)
   #define HAS_Z_MIN_PROBE_PIN 1
 #endif
 

Marlin/src/module/endstops.cpp

@@ -329,7 +329,7 @@ void Endstops::init() {
     #endif
   #endif
 
-  #if HAS_CUSTOM_PROBE_PIN
+  #if USES_Z_MIN_PROBE_PIN
     #if ENABLED(ENDSTOPPULLUP_ZMIN_PROBE)
       SET_INPUT_PULLUP(Z_MIN_PROBE_PIN);
     #elif ENABLED(ENDSTOPPULLDOWN_ZMIN_PROBE)
@@ -453,7 +453,7 @@ void Endstops::event_handler() {
       _ENDSTOP_HIT_TEST(K,'K')
     );
 
-    #if HAS_CUSTOM_PROBE_PIN
+    #if USES_Z_MIN_PROBE_PIN
       #define P_AXIS Z_AXIS
       if (TEST(hit_state, Z_MIN_PROBE)) _ENDSTOP_HIT_ECHO(P, 'P');
     #endif
@@ -566,7 +566,7 @@ void _O2 Endstops::report_states() {
   #if BOTH(MARLIN_DEV_MODE, PROBE_ACTIVATION_SWITCH)
     print_es_state(probe_switch_activated(), PSTR(STR_PROBE_EN));
   #endif
-  #if HAS_CUSTOM_PROBE_PIN
+  #if USES_Z_MIN_PROBE_PIN
     print_es_state(PROBE_TRIGGERED(), PSTR(STR_Z_PROBE));
   #endif
   #if MULTI_FILAMENT_SENSOR
@@ -720,7 +720,7 @@ void Endstops::update() {
   #if HAS_BED_PROBE
     // When closing the gap check the enabled probe
     if (probe_switch_activated())
-      UPDATE_ENDSTOP_BIT(Z, TERN(HAS_CUSTOM_PROBE_PIN, MIN_PROBE, MIN));
+      UPDATE_ENDSTOP_BIT(Z, TERN(USES_Z_MIN_PROBE_PIN, MIN_PROBE, MIN));
   #endif
 
   #if HAS_Z_MAX && !Z_SPI_SENSORLESS
@@ -746,7 +746,7 @@ void Endstops::update() {
           COPY_LIVE_STATE(Z_MAX, Z4_MAX);
         #endif
       #endif
-    #elif !HAS_CUSTOM_PROBE_PIN || Z_MAX_PIN != Z_MIN_PROBE_PIN
+    #elif !USES_Z_MIN_PROBE_PIN || Z_MAX_PIN != Z_MIN_PROBE_PIN
       // If this pin isn't the bed probe it's the Z endstop
       UPDATE_ENDSTOP_BIT(Z, MAX);
     #endif
@@ -1021,7 +1021,7 @@ void Endstops::update() {
 
         #if HAS_Z_MIN || (Z_SPI_SENSORLESS && Z_HOME_TO_MIN)
           if ( TERN1(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN, z_probe_enabled)
-            && TERN1(HAS_CUSTOM_PROBE_PIN, !z_probe_enabled)
+            && TERN1(USES_Z_MIN_PROBE_PIN, !z_probe_enabled)
           ) PROCESS_ENDSTOP_Z(MIN);
           #if   CORE_DIAG(XZ, X, MIN)
             PROCESS_CORE_ENDSTOP(X,MIN,Z,MIN);
@@ -1035,7 +1035,7 @@ void Endstops::update() {
         #endif
 
         // When closing the gap check the enabled probe
-        #if HAS_CUSTOM_PROBE_PIN
+        #if USES_Z_MIN_PROBE_PIN
           if (z_probe_enabled) PROCESS_ENDSTOP(Z, MIN_PROBE);
         #endif
       }
@@ -1043,7 +1043,7 @@ void Endstops::update() {
         #if HAS_Z_MAX || (Z_SPI_SENSORLESS && Z_HOME_TO_MAX)
           #if ENABLED(Z_MULTI_ENDSTOPS)
             PROCESS_ENDSTOP_Z(MAX);
-          #elif !HAS_CUSTOM_PROBE_PIN || Z_MAX_PIN != Z_MIN_PROBE_PIN  // No probe or probe is Z_MIN || Probe is not Z_MAX
+          #elif !USES_Z_MIN_PROBE_PIN || Z_MAX_PIN != Z_MIN_PROBE_PIN  // No probe or probe is Z_MIN || Probe is not Z_MAX
             PROCESS_ENDSTOP(Z, MAX);
           #endif
           #if   CORE_DIAG(XZ, X, MIN)

Marlin/src/module/endstops.h

@@ -69,7 +69,7 @@ enum EndstopEnum : char {
   #endif
 
   // Bed Probe state is distinct or shared with Z_MIN (i.e., when the probe is the only Z endstop)
-  _ES_ITEM(HAS_BED_PROBE, Z_MIN_PROBE IF_DISABLED(HAS_CUSTOM_PROBE_PIN, = Z_MIN))
+  _ES_ITEM(HAS_BED_PROBE, Z_MIN_PROBE IF_DISABLED(USES_Z_MIN_PROBE_PIN, = Z_MIN))
 
   // The total number of states
   NUM_ENDSTOP_STATES

Marlin/src/module/probe.h

@@ -38,7 +38,7 @@
   };
 #endif
 
-#if HAS_CUSTOM_PROBE_PIN
+#if USES_Z_MIN_PROBE_PIN
   #define PROBE_TRIGGERED() (READ(Z_MIN_PROBE_PIN) != Z_MIN_PROBE_ENDSTOP_INVERTING)
 #else
   #define PROBE_TRIGGERED() (READ(Z_MIN_PIN) != Z_MIN_ENDSTOP_INVERTING)

Marlin/src/pins/pins_postprocess.h

@@ -1134,7 +1134,7 @@
   #define USE_ZMIN_PLUG
 #endif
 #undef _STOP_IN_USE
-#if !HAS_CUSTOM_PROBE_PIN
+#if !USES_Z_MIN_PROBE_PIN
   #undef Z_MIN_PROBE_PIN
   #define Z_MIN_PROBE_PIN    -1
 #endif

Marlin/src/pins/sam/pins_RURAMPS4D_11.h

@@ -117,7 +117,7 @@
 //#define E3_MS2_PIN         ?
 //#define E3_MS3_PIN         ?
 
-#if HAS_CUSTOM_PROBE_PIN
+#if USES_Z_MIN_PROBE_PIN
   #define Z_MIN_PROBE_PIN                     49
 #endif
 

Marlin/src/pins/sam/pins_RURAMPS4D_13.h

@@ -105,7 +105,7 @@
   #define E2_CS_PIN                           61
 #endif
 
-#if HAS_CUSTOM_PROBE_PIN
+#if USES_Z_MIN_PROBE_PIN
   #define Z_MIN_PROBE_PIN                     49
 #endif