Fix and improve FYSETC LCD support (#13767)
This commit is contained in:
parent
4e35e6c705
commit
81ca5a4cd4
|
@ -1910,6 +1910,12 @@
|
||||||
// https://wiki.fysetc.com/Mini12864_Panel/?fbclid=IwAR1FyjuNdVOOy9_xzky3qqo_WeM5h-4gpRnnWhQr_O1Ef3h0AFnFXmCehK8
|
// https://wiki.fysetc.com/Mini12864_Panel/?fbclid=IwAR1FyjuNdVOOy9_xzky3qqo_WeM5h-4gpRnnWhQr_O1Ef3h0AFnFXmCehK8
|
||||||
//
|
//
|
||||||
//#define FYSETC_MINI_12864
|
//#define FYSETC_MINI_12864
|
||||||
|
#ifdef FYSETC_MINI_12864
|
||||||
|
#define FYSETC_MINI_12864_REV_1_2 // types C, D, E & F back light is monochrome (always on) - discrete RGB signals
|
||||||
|
//#define FYSETC_MINI_12864_REV_2_0 // types A & B back light is RGB - requires LED_USER_PRESET_STARTUP - discrete RGB signals
|
||||||
|
//#define FYSETC_MINI_12864_REV_2_1 // types A & B back light is RGB - requires LED_USER_PRESET_STARTUP - RGB
|
||||||
|
//#define FYSETC_MINI_12864_REV_2_1 // types A & B back light is RGB - requires LED_USER_PRESET_STARTUP - Neopixel
|
||||||
|
#endif
|
||||||
|
|
||||||
//
|
//
|
||||||
// Factory display for Creality CR-10
|
// Factory display for Creality CR-10
|
||||||
|
|
|
@ -53,7 +53,7 @@
|
||||||
// Public functions
|
// Public functions
|
||||||
// --------------------------------------------------------------------------
|
// --------------------------------------------------------------------------
|
||||||
|
|
||||||
#if ENABLED(DUE_SOFTWARE_SPI)
|
#if EITHER(DUE_SOFTWARE_SPI, FORCE_SOFT_SPI)
|
||||||
|
|
||||||
// --------------------------------------------------------------------------
|
// --------------------------------------------------------------------------
|
||||||
// software SPI
|
// software SPI
|
||||||
|
@ -739,7 +739,42 @@
|
||||||
#define SPI_MODE_2_DUE_HW 0
|
#define SPI_MODE_2_DUE_HW 0
|
||||||
#define SPI_MODE_3_DUE_HW 1
|
#define SPI_MODE_3_DUE_HW 1
|
||||||
|
|
||||||
|
/**
|
||||||
|
* The DUE SPI controller is set up so the upper word of the longword
|
||||||
|
* written to the transmit data register selects which SPI Chip Select
|
||||||
|
* Register is used. This allows different streams to have different SPI
|
||||||
|
* settings.
|
||||||
|
*
|
||||||
|
* In practice it's spooky. Some combinations hang the system, while others
|
||||||
|
* upset the peripheral device.
|
||||||
|
*
|
||||||
|
* SPI mode should be the same for all streams. The FYSETC_MINI_12864 gets
|
||||||
|
* upset if the clock phase changes after chip select goes active.
|
||||||
|
*
|
||||||
|
* SPI_CSR_CSAAT should be set for all streams. If not the WHILE_TX(0)
|
||||||
|
* macro returns immediately which can result in the SPI chip select going
|
||||||
|
* inactive before all the data has been sent.
|
||||||
|
*
|
||||||
|
* The TMC2130 library uses SPI0->SPI_CSR[3].
|
||||||
|
*
|
||||||
|
* The U8G hardware SPI uses SPI0->SPI_CSR[0]. The system hangs and/or the
|
||||||
|
* FYSETC_MINI_12864 gets upset if lower baud rates are used and the SD card
|
||||||
|
* is inserted or removed.
|
||||||
|
*
|
||||||
|
* The SD card uses SPI0->SPI_CSR[3]. Efforts were made to use [1] and [2]
|
||||||
|
* but they all resulted in hangs or garbage on the LCD.
|
||||||
|
*
|
||||||
|
* The SPI controlled chip selects are NOT enabled in the GPIO controller.
|
||||||
|
* The application must control the chip select.
|
||||||
|
*
|
||||||
|
* All of the above can be avoided by defining FORCE_SOFT_SPI to force the
|
||||||
|
* display to use software SPI.
|
||||||
|
*
|
||||||
|
*/
|
||||||
|
|
||||||
void spiInit(uint8_t spiRate=6) { // Default to slowest rate if not specified)
|
void spiInit(uint8_t spiRate=6) { // Default to slowest rate if not specified)
|
||||||
|
// Also sets U8G SPI rate to 4MHz and the SPI mode to 3
|
||||||
|
|
||||||
// 8.4 MHz, 4 MHz, 2 MHz, 1 MHz, 0.5 MHz, 0.329 MHz, 0.329 MHz
|
// 8.4 MHz, 4 MHz, 2 MHz, 1 MHz, 0.5 MHz, 0.329 MHz, 0.329 MHz
|
||||||
constexpr int spiDivider[] = { 10, 21, 42, 84, 168, 255, 255 };
|
constexpr int spiDivider[] = { 10, 21, 42, 84, 168, 255, 255 };
|
||||||
if (spiRate > 6) spiRate = 1;
|
if (spiRate > 6) spiRate = 1;
|
||||||
|
@ -760,15 +795,16 @@
|
||||||
// TMC2103 compatible setup
|
// TMC2103 compatible setup
|
||||||
// Master mode, no fault detection, PCS bits in data written to TDR select CSR register
|
// Master mode, no fault detection, PCS bits in data written to TDR select CSR register
|
||||||
SPI0->SPI_MR = SPI_MR_MSTR | SPI_MR_PS | SPI_MR_MODFDIS;
|
SPI0->SPI_MR = SPI_MR_MSTR | SPI_MR_PS | SPI_MR_MODFDIS;
|
||||||
// SPI mode 0, 8 Bit data transfer, baud rate
|
// SPI mode 3, 8 Bit data transfer, baud rate
|
||||||
SPI0->SPI_CSR[3] = SPI_CSR_SCBR(spiDivider[spiRate]) | SPI_CSR_CSAAT | SPI_MODE_0_DUE_HW; // use same CSR as TMC2130
|
SPI0->SPI_CSR[3] = SPI_CSR_SCBR(spiDivider[spiRate]) | SPI_CSR_CSAAT | SPI_MODE_3_DUE_HW; // use same CSR as TMC2130
|
||||||
|
SPI0->SPI_CSR[0] = SPI_CSR_SCBR(spiDivider[1]) | SPI_CSR_CSAAT | SPI_MODE_3_DUE_HW; // U8G default to 4MHz
|
||||||
}
|
}
|
||||||
|
|
||||||
void spiBegin() { spiInit(); }
|
void spiBegin() { spiInit(); }
|
||||||
|
|
||||||
static uint8_t spiTransfer(uint8_t data) {
|
static uint8_t spiTransfer(uint8_t data) {
|
||||||
WHILE_TX(0);
|
WHILE_TX(0);
|
||||||
SPI0->SPI_TDR = (uint32_t)data | 0x00070000UL; // Add TMC2130 PCS bits to every byte
|
SPI0->SPI_TDR = (uint32_t)data | 0x00070000UL; // Add TMC2130 PCS bits to every byte (use SPI0->SPI_CSR[3])
|
||||||
WHILE_TX(0);
|
WHILE_TX(0);
|
||||||
WHILE_RX(0);
|
WHILE_RX(0);
|
||||||
return SPI0->SPI_RDR;
|
return SPI0->SPI_RDR;
|
||||||
|
|
|
@ -138,6 +138,8 @@
|
||||||
#elif ENABLED(MKS_MINI_12864)
|
#elif ENABLED(MKS_MINI_12864)
|
||||||
|
|
||||||
#define MINIPANEL
|
#define MINIPANEL
|
||||||
|
#define DEFAULT_LCD_CONTRAST 150
|
||||||
|
#define LCD_CONTRAST_MAX 255
|
||||||
|
|
||||||
#elif ENABLED(FYSETC_MINI_12864)
|
#elif ENABLED(FYSETC_MINI_12864)
|
||||||
|
|
||||||
|
@ -153,7 +155,9 @@
|
||||||
#if EITHER(MAKRPANEL, MINIPANEL)
|
#if EITHER(MAKRPANEL, MINIPANEL)
|
||||||
#define DOGLCD
|
#define DOGLCD
|
||||||
#define ULTIPANEL
|
#define ULTIPANEL
|
||||||
#define DEFAULT_LCD_CONTRAST 17
|
#ifndef DEFAULT_LCD_CONTRAST
|
||||||
|
#define DEFAULT_LCD_CONTRAST 17
|
||||||
|
#endif
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
#if ENABLED(ULTI_CONTROLLER)
|
#if ENABLED(ULTI_CONTROLLER)
|
||||||
|
|
|
@ -1786,13 +1786,6 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
|
||||||
#error "Please select no more than one LCD controller option."
|
#error "Please select no more than one LCD controller option."
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
/**
|
|
||||||
* Fysetc Mini 12864 requirements
|
|
||||||
*/
|
|
||||||
#if ENABLED(FYSETC_MINI_12864) && DISABLED(LED_USER_PRESET_STARTUP)
|
|
||||||
#error "FYSETC_MINI_12864 requires LED_USER_PRESET_STARTUP to enable the backlight on startup."
|
|
||||||
#endif
|
|
||||||
|
|
||||||
/**
|
/**
|
||||||
* Check existing CS pins against enabled TMC SPI drivers.
|
* Check existing CS pins against enabled TMC SPI drivers.
|
||||||
*/
|
*/
|
||||||
|
|
|
@ -94,3 +94,16 @@ public:
|
||||||
: U8GLIB(&u8g_dev_tft_320x240_upscale_from_128x64, cs, rs, reset)
|
: U8GLIB(&u8g_dev_tft_320x240_upscale_from_128x64, cs, rs, reset)
|
||||||
{ }
|
{ }
|
||||||
};
|
};
|
||||||
|
|
||||||
|
|
||||||
|
extern u8g_dev_t u8g_dev_uc1701_mini12864_HAL_2x_sw_spi, u8g_dev_uc1701_mini12864_HAL_2x_hw_spi;
|
||||||
|
|
||||||
|
class U8GLIB_MINI12864_2X_HAL : public U8GLIB {
|
||||||
|
public:
|
||||||
|
U8GLIB_MINI12864_2X_HAL(uint8_t sck, uint8_t mosi, uint8_t cs, uint8_t a0, uint8_t reset = U8G_PIN_NONE)
|
||||||
|
: U8GLIB(&u8g_dev_uc1701_mini12864_HAL_2x_sw_spi, sck, mosi, cs, a0, reset)
|
||||||
|
{ }
|
||||||
|
U8GLIB_MINI12864_2X_HAL(uint8_t cs, uint8_t a0, uint8_t reset = U8G_PIN_NONE)
|
||||||
|
: U8GLIB(&u8g_dev_uc1701_mini12864_HAL_2x_hw_spi, cs, a0, reset)
|
||||||
|
{ }
|
||||||
|
};
|
||||||
|
|
|
@ -66,42 +66,47 @@
|
||||||
#define PAGE_HEIGHT 8
|
#define PAGE_HEIGHT 8
|
||||||
|
|
||||||
static const uint8_t u8g_dev_uc1701_mini12864_HAL_init_seq[] PROGMEM = {
|
static const uint8_t u8g_dev_uc1701_mini12864_HAL_init_seq[] PROGMEM = {
|
||||||
U8G_ESC_CS(0), /* disable chip */
|
U8G_ESC_CS(0), /* disable chip */
|
||||||
U8G_ESC_ADR(0), /* instruction mode */
|
U8G_ESC_ADR(0), /* instruction mode */
|
||||||
U8G_ESC_RST(1), /* do reset low pulse with (1*16)+2 milliseconds */
|
U8G_ESC_RST(1), /* do reset low pulse with (1*16)+2 milliseconds */
|
||||||
U8G_ESC_CS(1), /* enable chip */
|
U8G_ESC_CS(1), /* enable chip */
|
||||||
|
|
||||||
0x0E2, /* soft reset */
|
0x0E2, /* soft reset */
|
||||||
0x040, /* set display start line to 0 */
|
0x040, /* set display start line to 0 */
|
||||||
0x0A0, /* ADC set to reverse */
|
0x0A0, /* ADC set to reverse */
|
||||||
0x0C8, /* common output mode */
|
0x0C8, /* common output mode */
|
||||||
0x0A6, /* display normal, bit val 0: LCD pixel off. */
|
0x0A6, /* display normal, bit val 0: LCD pixel off. */
|
||||||
0x0A2, /* LCD bias 1/9 */
|
0x0A2, /* LCD bias 1/9 */
|
||||||
0x02F, /* all power control circuits on */
|
0x02F, /* all power control circuits on */
|
||||||
0x0F8, /* set booster ratio to */
|
0x0F8, /* set booster ratio to */
|
||||||
0x000, /* 4x */
|
0x000, /* 4x */
|
||||||
0x023, /* set V0 voltage resistor ratio to large */
|
0x023, /* set V0 voltage resistor ratio to large */
|
||||||
0x081, /* set contrast */
|
0x081, /* set contrast */
|
||||||
0x027, /* contrast value */
|
0x027, /* contrast value */
|
||||||
0x0AC, /* indicator */
|
0x0AC, /* indicator */
|
||||||
0x000, /* disable */
|
0x000, /* disable */
|
||||||
0x0AF, /* display on */
|
0x0AF, /* display on */
|
||||||
|
|
||||||
U8G_ESC_DLY(100), /* delay 100 ms */
|
U8G_ESC_CS(0), /* disable chip */
|
||||||
0x0A5, /* display all points, ST7565 */
|
U8G_ESC_DLY(100), /* delay 100 ms */
|
||||||
U8G_ESC_DLY(100), /* delay 100 ms */
|
U8G_ESC_CS(1), /* enable chip */
|
||||||
U8G_ESC_DLY(100), /* delay 100 ms */
|
|
||||||
0x0A4, /* normal display */
|
0x0A5, /* display all points, ST7565 */
|
||||||
U8G_ESC_CS(0), /* disable chip */
|
U8G_ESC_CS(0), /* disable chip */
|
||||||
U8G_ESC_END /* end of sequence */
|
U8G_ESC_DLY(100), /* delay 100 ms */
|
||||||
|
U8G_ESC_DLY(100), /* delay 100 ms */
|
||||||
|
U8G_ESC_CS(1), /* enable chip */
|
||||||
|
0x0A4, /* normal display */
|
||||||
|
U8G_ESC_CS(0), /* disable chip */
|
||||||
|
U8G_ESC_END /* end of sequence */
|
||||||
};
|
};
|
||||||
|
|
||||||
static const uint8_t u8g_dev_uc1701_mini12864_HAL_data_start[] PROGMEM = {
|
static const uint8_t u8g_dev_uc1701_mini12864_HAL_data_start[] PROGMEM = {
|
||||||
U8G_ESC_ADR(0), /* instruction mode */
|
U8G_ESC_ADR(0), /* instruction mode */
|
||||||
U8G_ESC_CS(1), /* enable chip */
|
U8G_ESC_CS(1), /* enable chip */
|
||||||
0x010, /* set upper 4 bit of the col adr to 0 */
|
0x010, /* set upper 4 bit of the col adr to 0 */
|
||||||
0x000, /* set lower 4 bit of the col adr to 4 */
|
0x000, /* set lower 4 bit of the col adr to 4 */
|
||||||
U8G_ESC_END /* end of sequence */
|
U8G_ESC_END /* end of sequence */
|
||||||
};
|
};
|
||||||
|
|
||||||
uint8_t u8g_dev_uc1701_mini12864_HAL_fn(u8g_t *u8g, u8g_dev_t *dev, uint8_t msg, void *arg) {
|
uint8_t u8g_dev_uc1701_mini12864_HAL_fn(u8g_t *u8g, u8g_dev_t *dev, uint8_t msg, void *arg) {
|
||||||
|
|
|
@ -111,8 +111,8 @@
|
||||||
// The MINIPanel display
|
// The MINIPanel display
|
||||||
//#define U8G_CLASS U8GLIB_MINI12864
|
//#define U8G_CLASS U8GLIB_MINI12864
|
||||||
//#define U8G_PARAM DOGLCD_CS, DOGLCD_A0 // 8 stripes
|
//#define U8G_PARAM DOGLCD_CS, DOGLCD_A0 // 8 stripes
|
||||||
#define U8G_CLASS U8GLIB_MINI12864_2X
|
#define U8G_CLASS U8GLIB_MINI12864_2X_HAL
|
||||||
#if ENABLED(FYSETC_MINI_12864) && DOGLCD_SCK > 0
|
#if BOTH(FYSETC_MINI_12864, FORCE_SOFT_SPI)
|
||||||
#define U8G_PARAM DOGLCD_SCK, DOGLCD_MOSI, DOGLCD_CS, DOGLCD_A0 // 4 stripes SW-SPI
|
#define U8G_PARAM DOGLCD_SCK, DOGLCD_MOSI, DOGLCD_CS, DOGLCD_A0 // 4 stripes SW-SPI
|
||||||
#else
|
#else
|
||||||
#define U8G_PARAM DOGLCD_CS, DOGLCD_A0 // 4 stripes HW-SPI
|
#define U8G_PARAM DOGLCD_CS, DOGLCD_A0 // 4 stripes HW-SPI
|
||||||
|
|
|
@ -668,6 +668,7 @@ void MarlinUI::update() {
|
||||||
|
|
||||||
static uint16_t max_display_update_time = 0;
|
static uint16_t max_display_update_time = 0;
|
||||||
static millis_t next_lcd_update_ms;
|
static millis_t next_lcd_update_ms;
|
||||||
|
millis_t ms = millis();
|
||||||
|
|
||||||
#if HAS_LCD_MENU
|
#if HAS_LCD_MENU
|
||||||
|
|
||||||
|
@ -729,11 +730,12 @@ void MarlinUI::update() {
|
||||||
|
|
||||||
refresh();
|
refresh();
|
||||||
init_lcd(); // May revive the LCD if static electricity killed it
|
init_lcd(); // May revive the LCD if static electricity killed it
|
||||||
|
ms = millis();
|
||||||
|
next_lcd_update_ms = ms + LCD_UPDATE_INTERVAL; // delay LCD update until after SD activity completes
|
||||||
}
|
}
|
||||||
|
|
||||||
#endif // SDSUPPORT && SD_DETECT_PIN
|
#endif // SDSUPPORT && SD_DETECT_PIN
|
||||||
|
|
||||||
const millis_t ms = millis();
|
|
||||||
if (ELAPSED(ms, next_lcd_update_ms)
|
if (ELAPSED(ms, next_lcd_update_ms)
|
||||||
#if HAS_GRAPHICAL_LCD
|
#if HAS_GRAPHICAL_LCD
|
||||||
|| drawing_screen
|
|| drawing_screen
|
||||||
|
|
|
@ -204,24 +204,43 @@
|
||||||
#if ENABLED(FYSETC_MINI_12864)
|
#if ENABLED(FYSETC_MINI_12864)
|
||||||
#define DOGLCD_CS P1_18
|
#define DOGLCD_CS P1_18
|
||||||
#define DOGLCD_A0 P1_19
|
#define DOGLCD_A0 P1_19
|
||||||
#define LCD_RESET_PIN P1_20
|
|
||||||
#define LCD_BACKLIGHT_PIN -1
|
#define LCD_BACKLIGHT_PIN -1
|
||||||
|
|
||||||
#define RGB_LED
|
#define LCD_RESET_PIN P1_20 // Must be high or open for LCD to operate normally.
|
||||||
#ifndef RGB_LED_R_PIN
|
// Seems to work best if left open.
|
||||||
#define RGB_LED_R_PIN P1_21
|
|
||||||
#endif
|
#define FYSETC_MINI_12864_REV_1_2
|
||||||
#ifndef RGB_LED_G_PIN
|
//#define FYSETC_MINI_12864_REV_2_0
|
||||||
#define RGB_LED_G_PIN P1_22
|
//#define FYSETC_MINI_12864_REV_2_1
|
||||||
#endif
|
#if EITHER(FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0)
|
||||||
#ifndef RGB_LED_B_PIN
|
#define RGB_LED
|
||||||
#define RGB_LED_B_PIN P1_23
|
#ifndef RGB_LED_R_PIN
|
||||||
#endif
|
#define RGB_LED_R_PIN P1_21
|
||||||
#ifndef RGB_LED_W_PIN
|
#endif
|
||||||
#define RGB_LED_W_PIN -1
|
#ifndef RGB_LED_G_PIN
|
||||||
|
#define RGB_LED_G_PIN P1_22
|
||||||
|
#endif
|
||||||
|
#ifndef RGB_LED_B_PIN
|
||||||
|
#define RGB_LED_B_PIN P1_23
|
||||||
|
#endif
|
||||||
|
#elif defined(FYSETC_MINI_12864_REV_2_1)
|
||||||
|
#define NEOPIXEL_LED
|
||||||
|
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
|
||||||
|
#define NEOPIXEL_PIN P1_21 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
|
||||||
|
#define NEOPIXEL_PIXELS 3 // Number of LEDs in the strip
|
||||||
|
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
|
||||||
|
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255)
|
||||||
|
#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||||
|
#else
|
||||||
|
#error "Either FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0 or FYSETC_MINI_12864_REV_2_1 must be defined"
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
#else
|
#if !defined(LED_USER_PRESET_STARTUP) && EITHER(FYSETC_MINI_12864_REV_2_0, FYSETC_MINI_12864_REV_2_1)
|
||||||
|
#error "LED_USER_PRESET_STARTUP must be enabled when using FYSETC_MINI_12864 REV 2.0 and later"
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#else // !FYSETC_MINI_12864
|
||||||
|
|
||||||
#if ENABLED(MKS_MINI_12864)
|
#if ENABLED(MKS_MINI_12864)
|
||||||
#define DOGLCD_CS P1_21
|
#define DOGLCD_CS P1_21
|
||||||
|
@ -234,7 +253,7 @@
|
||||||
#define LCD_PINS_D7 P1_23
|
#define LCD_PINS_D7 P1_23
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
#endif // FYSETC_MINI_12864
|
#endif // !FYSETC_MINI_12864
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
|
@ -28,8 +28,8 @@
|
||||||
#error "Oops! Select 'FYSETC F6' in 'Tools > Board.'"
|
#error "Oops! Select 'FYSETC F6' in 'Tools > Board.'"
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
#ifdef SD_DETECT_INVERTED
|
#if ENABLED(SD_DETECT_INVERTED)
|
||||||
#error "SD_DETECT_INVERTED must be disabled for the FYSETC_F6_13 board."
|
//#error "SD_DETECT_INVERTED must be disabled for the FYSETC_F6_13 board."
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
#define BOARD_NAME "FYSETC F6 1.3"
|
#define BOARD_NAME "FYSETC F6 1.3"
|
||||||
|
@ -190,20 +190,42 @@
|
||||||
//
|
//
|
||||||
#define DOGLCD_A0 16
|
#define DOGLCD_A0 16
|
||||||
#define DOGLCD_CS 17
|
#define DOGLCD_CS 17
|
||||||
#ifndef RGB_LED_R_PIN
|
|
||||||
#define RGB_LED_R_PIN 25
|
|
||||||
#endif
|
|
||||||
#ifndef RGB_LED_G_PIN
|
|
||||||
#define RGB_LED_G_PIN 27
|
|
||||||
#endif
|
|
||||||
#ifndef RGB_LED_B_PIN
|
|
||||||
#define RGB_LED_B_PIN 29
|
|
||||||
#endif
|
|
||||||
|
|
||||||
#define LCD_BACKLIGHT_PIN -1
|
#define LCD_BACKLIGHT_PIN -1
|
||||||
#define LCD_RESET_PIN 23
|
|
||||||
#define KILL_PIN 41
|
#define KILL_PIN 41
|
||||||
|
|
||||||
|
#define LCD_RESET_PIN 23 // Must be high or open for LCD to operate normally.
|
||||||
|
// Seems to work best if left open.
|
||||||
|
|
||||||
|
#define FYSETC_MINI_12864_REV_1_2
|
||||||
|
//#define FYSETC_MINI_12864_REV_2_0
|
||||||
|
//#define FYSETC_MINI_12864_REV_2_1
|
||||||
|
#if EITHER(FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0)
|
||||||
|
#ifndef RGB_LED_R_PIN
|
||||||
|
#define RGB_LED_R_PIN 25
|
||||||
|
#endif
|
||||||
|
#ifndef RGB_LED_G_PIN
|
||||||
|
#define RGB_LED_G_PIN 27
|
||||||
|
#endif
|
||||||
|
#ifndef RGB_LED_B_PIN
|
||||||
|
#define RGB_LED_B_PIN 29
|
||||||
|
#endif
|
||||||
|
#elif defined(FYSETC_MINI_12864_REV_2_1)
|
||||||
|
#define NEOPIXEL_LED
|
||||||
|
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
|
||||||
|
#define NEOPIXEL_PIN 25 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
|
||||||
|
#define NEOPIXEL_PIXELS 3 // Number of LEDs in the strip
|
||||||
|
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
|
||||||
|
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255)
|
||||||
|
#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||||
|
#else
|
||||||
|
#error "Either FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0 or FYSETC_MINI_12864_REV_2_1 must be defined"
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#if !defined(LED_USER_PRESET_STARTUP) && EITHER(FYSETC_MINI_12864_REV_2_0, FYSETC_MINI_12864_REV_2_1)
|
||||||
|
#error "LED_USER_PRESET_STARTUP must be enabled when using FYSETC_MINI_12864 REV 2.0 and later"
|
||||||
|
#endif
|
||||||
|
|
||||||
#elif HAS_GRAPHICAL_LCD
|
#elif HAS_GRAPHICAL_LCD
|
||||||
|
|
||||||
#define LCD_PINS_RS 16
|
#define LCD_PINS_RS 16
|
||||||
|
|
|
@ -526,7 +526,6 @@
|
||||||
|
|
||||||
// From https://wiki.fysetc.com/Mini12864_Panel/?fbclid=IwAR1FyjuNdVOOy9_xzky3qqo_WeM5h-4gpRnnWhQr_O1Ef3h0AFnFXmCehK8
|
// From https://wiki.fysetc.com/Mini12864_Panel/?fbclid=IwAR1FyjuNdVOOy9_xzky3qqo_WeM5h-4gpRnnWhQr_O1Ef3h0AFnFXmCehK8
|
||||||
#define BEEPER_PIN 37
|
#define BEEPER_PIN 37
|
||||||
#define LCD_RESET_PIN 23
|
|
||||||
|
|
||||||
#define DOGLCD_A0 16
|
#define DOGLCD_A0 16
|
||||||
#define DOGLCD_CS 17
|
#define DOGLCD_CS 17
|
||||||
|
@ -537,14 +536,36 @@
|
||||||
|
|
||||||
#define SD_DETECT_PIN 49
|
#define SD_DETECT_PIN 49
|
||||||
|
|
||||||
#ifndef RGB_LED_R_PIN
|
#define LCD_RESET_PIN 23 // Must be high or open for LCD to operate normally.
|
||||||
#define RGB_LED_R_PIN 25
|
// Seems to work best if left open.
|
||||||
|
|
||||||
|
#define FYSETC_MINI_12864_REV_1_2
|
||||||
|
//#define FYSETC_MINI_12864_REV_2_0
|
||||||
|
//#define FYSETC_MINI_12864_REV_2_1
|
||||||
|
#if EITHER(FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0)
|
||||||
|
#ifndef RGB_LED_R_PIN
|
||||||
|
#define RGB_LED_R_PIN 25
|
||||||
|
#endif
|
||||||
|
#ifndef RGB_LED_G_PIN
|
||||||
|
#define RGB_LED_G_PIN 27
|
||||||
|
#endif
|
||||||
|
#ifndef RGB_LED_B_PIN
|
||||||
|
#define RGB_LED_B_PIN 29
|
||||||
|
#endif
|
||||||
|
#elif defined(FYSETC_MINI_12864_REV_2_1)
|
||||||
|
#define NEOPIXEL_LED
|
||||||
|
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
|
||||||
|
#define NEOPIXEL_PIN 25 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
|
||||||
|
#define NEOPIXEL_PIXELS 3 // Number of LEDs in the strip
|
||||||
|
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
|
||||||
|
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255)
|
||||||
|
#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||||
|
#else
|
||||||
|
#error "Either FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0 or FYSETC_MINI_12864_REV_2_1 must be defined"
|
||||||
#endif
|
#endif
|
||||||
#ifndef RGB_LED_G_PIN
|
|
||||||
#define RGB_LED_G_PIN 27
|
#if !defined(LED_USER_PRESET_STARTUP) && EITHER(FYSETC_MINI_12864_REV_2_0, FYSETC_MINI_12864_REV_2_1)
|
||||||
#endif
|
#error "LED_USER_PRESET_STARTUP must be enabled when using FYSETC_MINI_12864 REV 2.0 and later"
|
||||||
#ifndef RGB_LED_B_PIN
|
|
||||||
#define RGB_LED_B_PIN 29
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
#elif ENABLED(MINIPANEL)
|
#elif ENABLED(MINIPANEL)
|
||||||
|
|
|
@ -150,32 +150,71 @@
|
||||||
#if ENABLED(NEWPANEL)
|
#if ENABLED(NEWPANEL)
|
||||||
#define LCD_PINS_RS 16
|
#define LCD_PINS_RS 16
|
||||||
#define LCD_PINS_ENABLE 17
|
#define LCD_PINS_ENABLE 17
|
||||||
#define LCD_PINS_D4 23
|
|
||||||
#define LCD_PINS_D5 25
|
|
||||||
#define LCD_PINS_D6 27
|
|
||||||
#define LCD_PINS_D7 29
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
#if ENABLED(FYSETC_MINI_12864)
|
#if ENABLED(FYSETC_MINI_12864)
|
||||||
#define DOGLCD_CS LCD_PINS_ENABLE
|
#define DOGLCD_CS LCD_PINS_ENABLE
|
||||||
#define DOGLCD_A0 LCD_PINS_RS
|
#define DOGLCD_A0 LCD_PINS_RS
|
||||||
#elif ENABLED(MINIPANEL)
|
|
||||||
#define DOGLCD_CS 25
|
//#define FORCE_SOFT_SPI // Use this if default of hardware SPI causes problems
|
||||||
#define DOGLCD_A0 27
|
|
||||||
|
#define LCD_RESET_PIN 23 // Must be high or open for LCD to operate normally.
|
||||||
|
// Seems to work best if left open.
|
||||||
|
|
||||||
|
#define FYSETC_MINI_12864_REV_1_2
|
||||||
|
//#define FYSETC_MINI_12864_REV_2_0
|
||||||
|
//#define FYSETC_MINI_12864_REV_2_1
|
||||||
|
#if EITHER(FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0)
|
||||||
|
#ifndef RGB_LED_R_PIN
|
||||||
|
#define RGB_LED_R_PIN 25
|
||||||
|
#endif
|
||||||
|
#ifndef RGB_LED_G_PIN
|
||||||
|
#define RGB_LED_G_PIN 27
|
||||||
|
#endif
|
||||||
|
#ifndef RGB_LED_B_PIN
|
||||||
|
#define RGB_LED_B_PIN 29
|
||||||
|
#endif
|
||||||
|
#elif defined(FYSETC_MINI_12864_REV_2_1)
|
||||||
|
#define NEOPIXEL_LED
|
||||||
|
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
|
||||||
|
#define NEOPIXEL_PIN 25 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
|
||||||
|
#define NEOPIXEL_PIXELS 3 // Number of LEDs in the strip
|
||||||
|
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
|
||||||
|
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255)
|
||||||
|
#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||||
|
#else
|
||||||
|
#error "Either FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0 or FYSETC_MINI_12864_REV_2_1 must be defined"
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#if !defined(LED_USER_PRESET_STARTUP) && EITHER(FYSETC_MINI_12864_REV_2_0, FYSETC_MINI_12864_REV_2_1)
|
||||||
|
#error "LED_USER_PRESET_STARTUP must be enabled when using FYSETC_MINI_12864 REV 2.0 and later"
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#elif ENABLED(NEWPANEL)
|
||||||
|
|
||||||
|
#define LCD_PINS_D4 23
|
||||||
|
#define LCD_PINS_D5 25
|
||||||
|
#define LCD_PINS_D6 27
|
||||||
|
#define LCD_PINS_D7 29
|
||||||
|
|
||||||
|
#if ENABLED(MINIPANEL)
|
||||||
|
#define DOGLCD_CS 25
|
||||||
|
#define DOGLCD_A0 27
|
||||||
|
#endif
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
#if ANY(VIKI2, miniVIKI)
|
#if ANY(VIKI2, miniVIKI)
|
||||||
#define DOGLCD_A0 16
|
#define DOGLCD_A0 16
|
||||||
#define KILL_PIN 51
|
#define KILL_PIN 51
|
||||||
#define STAT_LED_BLUE_PIN 29
|
#define STAT_LED_BLUE_PIN 29
|
||||||
#define STAT_LED_RED_PIN 23
|
#define STAT_LED_RED_PIN 23
|
||||||
#define DOGLCD_CS 17
|
#define DOGLCD_CS 17
|
||||||
#define DOGLCD_SCK 76 // SCK_PIN - These are required for DUE Hardware SPI
|
#define DOGLCD_SCK 76 // SCK_PIN - Required for DUE Hardware SPI
|
||||||
#define DOGLCD_MOSI 75 // MOSI_PIN
|
#define DOGLCD_MOSI 75 // MOSI_PIN
|
||||||
#define DOGLCD_MISO 74 // MISO_PIN
|
#define DOGLCD_MISO 74 // MISO_PIN
|
||||||
#endif
|
#endif
|
||||||
|
|
||||||
|
|
||||||
#endif // ULTRA_LCD
|
#endif // ULTRA_LCD
|
||||||
|
|
||||||
#if HAS_DRIVER(TMC2208)
|
#if HAS_DRIVER(TMC2208)
|
||||||
|
@ -201,10 +240,8 @@
|
||||||
//
|
//
|
||||||
// M3/M4/M5 - Spindle/Laser Control
|
// M3/M4/M5 - Spindle/Laser Control
|
||||||
//
|
//
|
||||||
#if ENABLED(SPINDLE_LASER_ENABLE) && !PIN_EXISTS(SPINDLE_LASER_ENA)
|
#if HOTENDS < 3 && ENABLED(SPINDLE_LASER_ENABLE) && !PIN_EXISTS(SPINDLE_LASER_ENA)
|
||||||
#if HOTENDS < 3
|
#define SPINDLE_LASER_ENA_PIN 45 // Use E2 ENA
|
||||||
#define SPINDLE_LASER_ENA_PIN 45 // Use E2 ENA
|
#define SPINDLE_LASER_PWM_PIN 12 // MUST BE HARDWARE PWM
|
||||||
#define SPINDLE_LASER_PWM_PIN 12 // MUST BE HARDWARE PWM
|
#define SPINDLE_DIR_PIN 47 // Use E2 DIR
|
||||||
#define SPINDLE_DIR_PIN 47 // Use E2 DIR
|
|
||||||
#endif
|
|
||||||
#endif
|
#endif
|
||||||
|
|
|
@ -320,6 +320,7 @@
|
||||||
#define DOGLCD_MOSI P0_18
|
#define DOGLCD_MOSI P0_18
|
||||||
#define DOGLCD_CS P1_09 // use Ethernet connector for EXP1 cable signals
|
#define DOGLCD_CS P1_09 // use Ethernet connector for EXP1 cable signals
|
||||||
#define DOGLCD_A0 P1_14
|
#define DOGLCD_A0 P1_14
|
||||||
|
#define FORCE_SOFT_SPI // required on a Re-ARM system
|
||||||
#else
|
#else
|
||||||
#define DOGLCD_CS P0_26 // (63) J5-3 & AUX-2
|
#define DOGLCD_CS P0_26 // (63) J5-3 & AUX-2
|
||||||
#define DOGLCD_A0 P2_06 // (59) J3-8 & AUX-2
|
#define DOGLCD_A0 P2_06 // (59) J3-8 & AUX-2
|
||||||
|
|
|
@ -202,31 +202,24 @@
|
||||||
//
|
//
|
||||||
#if ENABLED(ULTRA_LCD)
|
#if ENABLED(ULTRA_LCD)
|
||||||
|
|
||||||
#if EITHER(RADDS_DISPLAY, REPRAP_DISCOUNT_SMART_CONTROLLER)
|
#if ANY(RADDS_DISPLAY, REPRAP_DISCOUNT_SMART_CONTROLLER, REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
|
||||||
|
|
||||||
#define BEEPER_PIN 62
|
#define BEEPER_PIN 62
|
||||||
|
#define LCD_PINS_D4 48
|
||||||
|
#define LCD_PINS_D5 50
|
||||||
|
#define LCD_PINS_D6 52
|
||||||
|
#define LCD_PINS_D7 53
|
||||||
|
#define SD_DETECT_PIN 51
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#if EITHER(RADDS_DISPLAY, REPRAP_DISCOUNT_SMART_CONTROLLER)
|
||||||
|
|
||||||
#define LCD_PINS_RS 63
|
#define LCD_PINS_RS 63
|
||||||
#define LCD_PINS_ENABLE 64
|
#define LCD_PINS_ENABLE 64
|
||||||
#define LCD_PINS_D4 48
|
|
||||||
#define LCD_PINS_D5 50
|
|
||||||
#define LCD_PINS_D6 52
|
|
||||||
#define LCD_PINS_D7 53
|
|
||||||
|
|
||||||
#define SD_DETECT_PIN 51
|
|
||||||
|
|
||||||
#elif ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
|
#elif ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
|
||||||
|
|
||||||
#define BEEPER_PIN 62
|
|
||||||
|
|
||||||
#define LCD_PINS_RS 52
|
#define LCD_PINS_RS 52
|
||||||
#define LCD_PINS_ENABLE 53
|
#define LCD_PINS_ENABLE 53
|
||||||
#define LCD_PINS_D4 48
|
|
||||||
#define LCD_PINS_D5 50
|
|
||||||
#define LCD_PINS_D6 52
|
|
||||||
#define LCD_PINS_D7 53
|
|
||||||
|
|
||||||
#define SD_DETECT_PIN 51
|
|
||||||
|
|
||||||
#elif HAS_SSD1306_OLED_I2C
|
#elif HAS_SSD1306_OLED_I2C
|
||||||
|
|
||||||
|
@ -234,16 +227,57 @@
|
||||||
#define LCD_SDSS 10
|
#define LCD_SDSS 10
|
||||||
#define SD_DETECT_PIN 51
|
#define SD_DETECT_PIN 51
|
||||||
|
|
||||||
|
#elif ENABLED(FYSETC_MINI_12864)
|
||||||
|
|
||||||
|
#define BEEPER_PIN 62
|
||||||
|
#define DOGLCD_CS 64
|
||||||
|
#define DOGLCD_A0 63
|
||||||
|
|
||||||
|
//#define FORCE_SOFT_SPI // Use this if default of hardware SPI causes problems
|
||||||
|
|
||||||
|
#define LCD_RESET_PIN 48 // Must be high or open for LCD to operate normally.
|
||||||
|
// Seems to work best if left open.
|
||||||
|
|
||||||
|
#define FYSETC_MINI_12864_REV_1_2
|
||||||
|
//#define FYSETC_MINI_12864_REV_2_0
|
||||||
|
//#define FYSETC_MINI_12864_REV_2_1
|
||||||
|
#if EITHER(FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0)
|
||||||
|
#define RGB_LED
|
||||||
|
#ifndef RGB_LED_R_PIN
|
||||||
|
#define RGB_LED_R_PIN 50 // D5
|
||||||
|
#endif
|
||||||
|
#ifndef RGB_LED_G_PIN
|
||||||
|
#define RGB_LED_G_PIN 52 // D6
|
||||||
|
#endif
|
||||||
|
#ifndef RGB_LED_B_PIN
|
||||||
|
#define RGB_LED_B_PIN 53 // D7
|
||||||
|
#endif
|
||||||
|
#elif defined(FYSETC_MINI_12864_REV_2_1)
|
||||||
|
#define NEOPIXEL_LED
|
||||||
|
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
|
||||||
|
#define NEOPIXEL_PIN 50 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
|
||||||
|
#define NEOPIXEL_PIXELS 3 // Number of LEDs in the strip
|
||||||
|
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
|
||||||
|
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255)
|
||||||
|
#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||||
|
#else
|
||||||
|
#error "Either FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0 or FYSETC_MINI_12864_REV_2_1 must be defined"
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#if !defined(LED_USER_PRESET_STARTUP) && EITHER(FYSETC_MINI_12864_REV_2_0, FYSETC_MINI_12864_REV_2_1)
|
||||||
|
#error "LED_USER_PRESET_STARTUP must be enabled when using FYSETC_MINI_12864 REV 2.0 and later"
|
||||||
|
#endif
|
||||||
|
|
||||||
#elif ENABLED(SPARK_FULL_GRAPHICS)
|
#elif ENABLED(SPARK_FULL_GRAPHICS)
|
||||||
|
|
||||||
//http://doku.radds.org/dokumentation/other-electronics/sparklcd/
|
//http://doku.radds.org/dokumentation/other-electronics/sparklcd/
|
||||||
#error "Oops! SPARK_FULL_GRAPHICS not supported with RURAMPS4D."
|
#error "Oops! SPARK_FULL_GRAPHICS not supported with RURAMPS4D."
|
||||||
//#define LCD_PINS_D4 29//?
|
//#define LCD_PINS_D4 29 //?
|
||||||
//#define LCD_PINS_ENABLE 27//?
|
//#define LCD_PINS_ENABLE 27 //?
|
||||||
//#define LCD_PINS_RS 25//?
|
//#define LCD_PINS_RS 25 //?
|
||||||
//#define BTN_EN1 35//?
|
//#define BTN_EN1 35 //?
|
||||||
//#define BTN_EN2 33//?
|
//#define BTN_EN2 33 //?
|
||||||
//#define BTN_ENC 37//?
|
//#define BTN_ENC 37 //?
|
||||||
|
|
||||||
#endif // SPARK_FULL_GRAPHICS
|
#endif // SPARK_FULL_GRAPHICS
|
||||||
|
|
||||||
|
|
|
@ -188,31 +188,24 @@
|
||||||
//
|
//
|
||||||
#if ENABLED(ULTRA_LCD)
|
#if ENABLED(ULTRA_LCD)
|
||||||
|
|
||||||
#if EITHER(RADDS_DISPLAY, REPRAP_DISCOUNT_SMART_CONTROLLER)
|
#if ANY(RADDS_DISPLAY, REPRAP_DISCOUNT_SMART_CONTROLLER, REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
|
||||||
|
|
||||||
#define BEEPER_PIN 62
|
#define BEEPER_PIN 62
|
||||||
|
#define LCD_PINS_D4 48
|
||||||
|
#define LCD_PINS_D5 50
|
||||||
|
#define LCD_PINS_D6 52
|
||||||
|
#define LCD_PINS_D7 53
|
||||||
|
#define SD_DETECT_PIN 51
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#if EITHER(RADDS_DISPLAY, REPRAP_DISCOUNT_SMART_CONTROLLER)
|
||||||
|
|
||||||
#define LCD_PINS_RS 63
|
#define LCD_PINS_RS 63
|
||||||
#define LCD_PINS_ENABLE 64
|
#define LCD_PINS_ENABLE 64
|
||||||
#define LCD_PINS_D4 48
|
|
||||||
#define LCD_PINS_D5 50
|
|
||||||
#define LCD_PINS_D6 52
|
|
||||||
#define LCD_PINS_D7 53
|
|
||||||
|
|
||||||
#define SD_DETECT_PIN 51
|
|
||||||
|
|
||||||
#elif ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
|
#elif ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
|
||||||
|
|
||||||
#define BEEPER_PIN 62
|
|
||||||
|
|
||||||
#define LCD_PINS_RS 52
|
#define LCD_PINS_RS 52
|
||||||
#define LCD_PINS_ENABLE 53
|
#define LCD_PINS_ENABLE 53
|
||||||
#define LCD_PINS_D4 48
|
|
||||||
#define LCD_PINS_D5 50
|
|
||||||
#define LCD_PINS_D6 52
|
|
||||||
#define LCD_PINS_D7 53
|
|
||||||
|
|
||||||
#define SD_DETECT_PIN 51
|
|
||||||
|
|
||||||
#elif HAS_SSD1306_OLED_I2C
|
#elif HAS_SSD1306_OLED_I2C
|
||||||
|
|
||||||
|
@ -220,6 +213,47 @@
|
||||||
#define LCD_SDSS 10
|
#define LCD_SDSS 10
|
||||||
#define SD_DETECT_PIN 51
|
#define SD_DETECT_PIN 51
|
||||||
|
|
||||||
|
#elif ENABLED(FYSETC_MINI_12864)
|
||||||
|
|
||||||
|
#define BEEPER_PIN 62
|
||||||
|
#define DOGLCD_CS 64
|
||||||
|
#define DOGLCD_A0 63
|
||||||
|
|
||||||
|
//#define FORCE_SOFT_SPI // Use this if default of hardware SPI causes problems
|
||||||
|
|
||||||
|
#define LCD_RESET_PIN 48 // Must be high or open for LCD to operate normally.
|
||||||
|
// Seems to work best if left open.
|
||||||
|
|
||||||
|
#define FYSETC_MINI_12864_REV_1_2
|
||||||
|
//#define FYSETC_MINI_12864_REV_2_0
|
||||||
|
//#define FYSETC_MINI_12864_REV_2_1
|
||||||
|
#if EITHER(FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0)
|
||||||
|
#define RGB_LED
|
||||||
|
#ifndef RGB_LED_R_PIN
|
||||||
|
#define RGB_LED_R_PIN 50 // D5
|
||||||
|
#endif
|
||||||
|
#ifndef RGB_LED_G_PIN
|
||||||
|
#define RGB_LED_G_PIN 52 // D6
|
||||||
|
#endif
|
||||||
|
#ifndef RGB_LED_B_PIN
|
||||||
|
#define RGB_LED_B_PIN 53 // D7
|
||||||
|
#endif
|
||||||
|
#elif defined(FYSETC_MINI_12864_REV_2_1)
|
||||||
|
#define NEOPIXEL_LED
|
||||||
|
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
|
||||||
|
#define NEOPIXEL_PIN 50 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
|
||||||
|
#define NEOPIXEL_PIXELS 3 // Number of LEDs in the strip
|
||||||
|
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
|
||||||
|
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255)
|
||||||
|
#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
|
||||||
|
#else
|
||||||
|
#error "Either FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0 or FYSETC_MINI_12864_REV_2_1 must be defined"
|
||||||
|
#endif
|
||||||
|
|
||||||
|
#if !defined(LED_USER_PRESET_STARTUP) && EITHER(FYSETC_MINI_12864_REV_2_0, FYSETC_MINI_12864_REV_2_1)
|
||||||
|
#error "LED_USER_PRESET_STARTUP must be enabled when using FYSETC_MINI_12864 REV 2.0 and later"
|
||||||
|
#endif
|
||||||
|
|
||||||
#elif ENABLED(MKS_MINI_12864)
|
#elif ENABLED(MKS_MINI_12864)
|
||||||
|
|
||||||
#define ORIG_BEEPER_PIN 62
|
#define ORIG_BEEPER_PIN 62
|
||||||
|
|
Loading…
Reference in a new issue