zaubentrucker/muele-marlin
1
0
Fork 0
Code Issues Pull requests Actions Packages Projects Releases Wiki Activity

Fix and improve FYSETC LCD support (#13767)

Browse source
This commit is contained in:
Bob Kuhn 2019-04-21 20:48:53 -05:00 committed by Scott Lahteine
parent 4e35e6c705
commit 81ca5a4cd4
15 changed files with 369 additions and 142 deletions
Show stats Download patch file Download diff file Expand all files Collapse all files

6
Marlin/Configuration.h
View file

@ -1910,6 +1910,12 @@
// https://wiki.fysetc.com/Mini12864_Panel/?fbclid=IwAR1FyjuNdVOOy9_xzky3qqo_WeM5h-4gpRnnWhQr_O1Ef3h0AFnFXmCehK8
//
//#define FYSETC_MINI_12864
#ifdef FYSETC_MINI_12864
#define FYSETC_MINI_12864_REV_1_2 // types C, D, E & F back light is monochrome (always on) - discrete RGB signals
//#define FYSETC_MINI_12864_REV_2_0 // types A & B back light is RGB - requires LED_USER_PRESET_STARTUP - discrete RGB signals
//#define FYSETC_MINI_12864_REV_2_1 // types A & B back light is RGB - requires LED_USER_PRESET_STARTUP - RGB
//#define FYSETC_MINI_12864_REV_2_1 // types A & B back light is RGB - requires LED_USER_PRESET_STARTUP - Neopixel
#endif
//
// Factory display for Creality CR-10

44
Marlin/src/HAL/HAL_DUE/HAL_spi_Due.cpp
View file

@ -53,7 +53,7 @@
// Public functions
// --------------------------------------------------------------------------
#if ENABLED(DUE_SOFTWARE_SPI)
#if EITHER(DUE_SOFTWARE_SPI, FORCE_SOFT_SPI)
// --------------------------------------------------------------------------
// software SPI
@ -739,7 +739,42 @@
#define SPI_MODE_2_DUE_HW 0
#define SPI_MODE_3_DUE_HW 1
/**
* The DUE SPI controller is set up so the upper word of the longword
* written to the transmit data register selects which SPI Chip Select
* Register is used. This allows different streams to have different SPI
* settings.
*
* In practice it's spooky. Some combinations hang the system, while others
* upset the peripheral device.
*
* SPI mode should be the same for all streams. The FYSETC_MINI_12864 gets
* upset if the clock phase changes after chip select goes active.
*
* SPI_CSR_CSAAT should be set for all streams. If not the WHILE_TX(0)
* macro returns immediately which can result in the SPI chip select going
* inactive before all the data has been sent.
*
* The TMC2130 library uses SPI0->SPI_CSR[3].
*
* The U8G hardware SPI uses SPI0->SPI_CSR[0]. The system hangs and/or the
* FYSETC_MINI_12864 gets upset if lower baud rates are used and the SD card
* is inserted or removed.
*
* The SD card uses SPI0->SPI_CSR[3]. Efforts were made to use [1] and [2]
* but they all resulted in hangs or garbage on the LCD.
*
* The SPI controlled chip selects are NOT enabled in the GPIO controller.
* The application must control the chip select.
*
* All of the above can be avoided by defining FORCE_SOFT_SPI to force the
* display to use software SPI.
*
*/
void spiInit(uint8_t spiRate=6) { // Default to slowest rate if not specified)
// Also sets U8G SPI rate to 4MHz and the SPI mode to 3
// 8.4 MHz, 4 MHz, 2 MHz, 1 MHz, 0.5 MHz, 0.329 MHz, 0.329 MHz
constexpr int spiDivider[] = { 10, 21, 42, 84, 168, 255, 255 };
if (spiRate > 6) spiRate = 1;
@ -760,15 +795,16 @@
// TMC2103 compatible setup
// Master mode, no fault detection, PCS bits in data written to TDR select CSR register
SPI0->SPI_MR = SPI_MR_MSTR | SPI_MR_PS | SPI_MR_MODFDIS;
// SPI mode 0, 8 Bit data transfer, baud rate
SPI0->SPI_CSR[3] = SPI_CSR_SCBR(spiDivider[spiRate]) | SPI_CSR_CSAAT | SPI_MODE_0_DUE_HW; // use same CSR as TMC2130
// SPI mode 3, 8 Bit data transfer, baud rate
SPI0->SPI_CSR[3] = SPI_CSR_SCBR(spiDivider[spiRate]) | SPI_CSR_CSAAT | SPI_MODE_3_DUE_HW; // use same CSR as TMC2130
SPI0->SPI_CSR[0] = SPI_CSR_SCBR(spiDivider[1]) | SPI_CSR_CSAAT | SPI_MODE_3_DUE_HW; // U8G default to 4MHz
}
void spiBegin() { spiInit(); }
static uint8_t spiTransfer(uint8_t data) {
WHILE_TX(0);
SPI0->SPI_TDR = (uint32_t)data | 0x00070000UL; // Add TMC2130 PCS bits to every byte
SPI0->SPI_TDR = (uint32_t)data | 0x00070000UL; // Add TMC2130 PCS bits to every byte (use SPI0->SPI_CSR[3])
WHILE_TX(0);
WHILE_RX(0);
return SPI0->SPI_RDR;

4
Marlin/src/inc/Conditionals_LCD.h
View file

@ -138,6 +138,8 @@
#elif ENABLED(MKS_MINI_12864)
#define MINIPANEL
#define DEFAULT_LCD_CONTRAST 150
#define LCD_CONTRAST_MAX 255
#elif ENABLED(FYSETC_MINI_12864)
@ -153,8 +155,10 @@
#if EITHER(MAKRPANEL, MINIPANEL)
#define DOGLCD
#define ULTIPANEL
#ifndef DEFAULT_LCD_CONTRAST
#define DEFAULT_LCD_CONTRAST 17
#endif
#endif
#if ENABLED(ULTI_CONTROLLER)
#define U8GLIB_SSD1309

7
Marlin/src/inc/SanityCheck.h
View file

@ -1786,13 +1786,6 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
#error "Please select no more than one LCD controller option."
#endif
/**
* Fysetc Mini 12864 requirements
*/
#if ENABLED(FYSETC_MINI_12864) && DISABLED(LED_USER_PRESET_STARTUP)
#error "FYSETC_MINI_12864 requires LED_USER_PRESET_STARTUP to enable the backlight on startup."
#endif
/**
* Check existing CS pins against enabled TMC SPI drivers.
*/

13
Marlin/src/lcd/dogm/HAL_LCD_class_defines.h
View file

@ -94,3 +94,16 @@ public:
: U8GLIB(&u8g_dev_tft_320x240_upscale_from_128x64, cs, rs, reset)
{ }
};
extern u8g_dev_t u8g_dev_uc1701_mini12864_HAL_2x_sw_spi, u8g_dev_uc1701_mini12864_HAL_2x_hw_spi;
class U8GLIB_MINI12864_2X_HAL : public U8GLIB {
public:
U8GLIB_MINI12864_2X_HAL(uint8_t sck, uint8_t mosi, uint8_t cs, uint8_t a0, uint8_t reset = U8G_PIN_NONE)
: U8GLIB(&u8g_dev_uc1701_mini12864_HAL_2x_sw_spi, sck, mosi, cs, a0, reset)
{ }
U8GLIB_MINI12864_2X_HAL(uint8_t cs, uint8_t a0, uint8_t reset = U8G_PIN_NONE)
: U8GLIB(&u8g_dev_uc1701_mini12864_HAL_2x_hw_spi, cs, a0, reset)
{ }
};

5
Marlin/src/lcd/dogm/u8g_dev_uc1701_mini12864_HAL.cpp
View file

@ -87,10 +87,15 @@ static const uint8_t u8g_dev_uc1701_mini12864_HAL_init_seq[] PROGMEM = {
0x000, /* disable */
0x0AF, /* display on */
U8G_ESC_CS(0), /* disable chip */
U8G_ESC_DLY(100), /* delay 100 ms */
U8G_ESC_CS(1), /* enable chip */
0x0A5, /* display all points, ST7565 */
U8G_ESC_CS(0), /* disable chip */
U8G_ESC_DLY(100), /* delay 100 ms */
U8G_ESC_DLY(100), /* delay 100 ms */
U8G_ESC_CS(1), /* enable chip */
0x0A4, /* normal display */
U8G_ESC_CS(0), /* disable chip */
U8G_ESC_END /* end of sequence */

4
Marlin/src/lcd/dogm/ultralcd_DOGM.h
View file

@ -111,8 +111,8 @@
// The MINIPanel display
//#define U8G_CLASS U8GLIB_MINI12864
//#define U8G_PARAM DOGLCD_CS, DOGLCD_A0 // 8 stripes
#define U8G_CLASS U8GLIB_MINI12864_2X
#if ENABLED(FYSETC_MINI_12864) && DOGLCD_SCK > 0
#define U8G_CLASS U8GLIB_MINI12864_2X_HAL
#if BOTH(FYSETC_MINI_12864, FORCE_SOFT_SPI)
#define U8G_PARAM DOGLCD_SCK, DOGLCD_MOSI, DOGLCD_CS, DOGLCD_A0 // 4 stripes SW-SPI
#else
#define U8G_PARAM DOGLCD_CS, DOGLCD_A0 // 4 stripes HW-SPI

4
Marlin/src/lcd/ultralcd.cpp
View file

@ -668,6 +668,7 @@ void MarlinUI::update() {
static uint16_t max_display_update_time = 0;
static millis_t next_lcd_update_ms;
millis_t ms = millis();
#if HAS_LCD_MENU
@ -729,11 +730,12 @@ void MarlinUI::update() {
refresh();
init_lcd(); // May revive the LCD if static electricity killed it
ms = millis();
next_lcd_update_ms = ms + LCD_UPDATE_INTERVAL; // delay LCD update until after SD activity completes
}
#endif // SDSUPPORT && SD_DETECT_PIN
const millis_t ms = millis();
if (ELAPSED(ms, next_lcd_update_ms)
#if HAS_GRAPHICAL_LCD
|| drawing_screen

29
Marlin/src/pins/pins_BIGTREE_SKR_V1.3.h
View file

@ -204,9 +204,16 @@
#if ENABLED(FYSETC_MINI_12864)
#define DOGLCD_CS P1_18
#define DOGLCD_A0 P1_19
#define LCD_RESET_PIN P1_20
#define LCD_BACKLIGHT_PIN -1
#define LCD_RESET_PIN P1_20 // Must be high or open for LCD to operate normally.
// Seems to work best if left open.
#define FYSETC_MINI_12864_REV_1_2
//#define FYSETC_MINI_12864_REV_2_0
//#define FYSETC_MINI_12864_REV_2_1
#if EITHER(FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0)
#define RGB_LED
#ifndef RGB_LED_R_PIN
#define RGB_LED_R_PIN P1_21
@ -217,11 +224,23 @@
#ifndef RGB_LED_B_PIN
#define RGB_LED_B_PIN P1_23
#endif
#ifndef RGB_LED_W_PIN
#define RGB_LED_W_PIN -1
#elif defined(FYSETC_MINI_12864_REV_2_1)
#define NEOPIXEL_LED
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN P1_21 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 3 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255)
#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#else
#error "Either FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0 or FYSETC_MINI_12864_REV_2_1 must be defined"
#endif
#else
#if !defined(LED_USER_PRESET_STARTUP) && EITHER(FYSETC_MINI_12864_REV_2_0, FYSETC_MINI_12864_REV_2_1)
#error "LED_USER_PRESET_STARTUP must be enabled when using FYSETC_MINI_12864 REV 2.0 and later"
#endif
#else // !FYSETC_MINI_12864
#if ENABLED(MKS_MINI_12864)
#define DOGLCD_CS P1_21
@ -234,7 +253,7 @@
#define LCD_PINS_D7 P1_23
#endif
#endif // FYSETC_MINI_12864
#endif // !FYSETC_MINI_12864
#endif

32
Marlin/src/pins/pins_FYSETC_F6_13.h
View file

@ -28,8 +28,8 @@
#error "Oops! Select 'FYSETC F6' in 'Tools > Board.'"
#endif
#ifdef SD_DETECT_INVERTED
#error "SD_DETECT_INVERTED must be disabled for the FYSETC_F6_13 board."
#if ENABLED(SD_DETECT_INVERTED)
//#error "SD_DETECT_INVERTED must be disabled for the FYSETC_F6_13 board."
#endif
#define BOARD_NAME "FYSETC F6 1.3"
@ -190,6 +190,17 @@
//
#define DOGLCD_A0 16
#define DOGLCD_CS 17
#define LCD_BACKLIGHT_PIN -1
#define KILL_PIN 41
#define LCD_RESET_PIN 23 // Must be high or open for LCD to operate normally.
// Seems to work best if left open.
#define FYSETC_MINI_12864_REV_1_2
//#define FYSETC_MINI_12864_REV_2_0
//#define FYSETC_MINI_12864_REV_2_1
#if EITHER(FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0)
#ifndef RGB_LED_R_PIN
#define RGB_LED_R_PIN 25
#endif
@ -199,10 +210,21 @@
#ifndef RGB_LED_B_PIN
#define RGB_LED_B_PIN 29
#endif
#elif defined(FYSETC_MINI_12864_REV_2_1)
#define NEOPIXEL_LED
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 25 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 3 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255)
#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#else
#error "Either FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0 or FYSETC_MINI_12864_REV_2_1 must be defined"
#endif
#define LCD_BACKLIGHT_PIN -1
#define LCD_RESET_PIN 23
#define KILL_PIN 41
#if !defined(LED_USER_PRESET_STARTUP) && EITHER(FYSETC_MINI_12864_REV_2_0, FYSETC_MINI_12864_REV_2_1)
#error "LED_USER_PRESET_STARTUP must be enabled when using FYSETC_MINI_12864 REV 2.0 and later"
#endif
#elif HAS_GRAPHICAL_LCD

23
Marlin/src/pins/pins_RAMPS.h
View file

@ -526,7 +526,6 @@
// From https://wiki.fysetc.com/Mini12864_Panel/?fbclid=IwAR1FyjuNdVOOy9_xzky3qqo_WeM5h-4gpRnnWhQr_O1Ef3h0AFnFXmCehK8
#define BEEPER_PIN 37
#define LCD_RESET_PIN 23
#define DOGLCD_A0 16
#define DOGLCD_CS 17
@ -537,6 +536,13 @@
#define SD_DETECT_PIN 49
#define LCD_RESET_PIN 23 // Must be high or open for LCD to operate normally.
// Seems to work best if left open.
#define FYSETC_MINI_12864_REV_1_2
//#define FYSETC_MINI_12864_REV_2_0
//#define FYSETC_MINI_12864_REV_2_1
#if EITHER(FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0)
#ifndef RGB_LED_R_PIN
#define RGB_LED_R_PIN 25
#endif
@ -546,6 +552,21 @@
#ifndef RGB_LED_B_PIN
#define RGB_LED_B_PIN 29
#endif
#elif defined(FYSETC_MINI_12864_REV_2_1)
#define NEOPIXEL_LED
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 25 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 3 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255)
#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#else
#error "Either FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0 or FYSETC_MINI_12864_REV_2_1 must be defined"
#endif
#if !defined(LED_USER_PRESET_STARTUP) && EITHER(FYSETC_MINI_12864_REV_2_0, FYSETC_MINI_12864_REV_2_1)
#error "LED_USER_PRESET_STARTUP must be enabled when using FYSETC_MINI_12864 REV 2.0 and later"
#endif
#elif ENABLED(MINIPANEL)

57
Marlin/src/pins/pins_RAMPS_FD_V1.h
View file

@ -150,32 +150,71 @@
#if ENABLED(NEWPANEL)
#define LCD_PINS_RS 16
#define LCD_PINS_ENABLE 17
#define LCD_PINS_D4 23
#define LCD_PINS_D5 25
#define LCD_PINS_D6 27
#define LCD_PINS_D7 29
#endif
#if ENABLED(FYSETC_MINI_12864)
#define DOGLCD_CS LCD_PINS_ENABLE
#define DOGLCD_A0 LCD_PINS_RS
#elif ENABLED(MINIPANEL)
//#define FORCE_SOFT_SPI // Use this if default of hardware SPI causes problems
#define LCD_RESET_PIN 23 // Must be high or open for LCD to operate normally.
// Seems to work best if left open.
#define FYSETC_MINI_12864_REV_1_2
//#define FYSETC_MINI_12864_REV_2_0
//#define FYSETC_MINI_12864_REV_2_1
#if EITHER(FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0)
#ifndef RGB_LED_R_PIN
#define RGB_LED_R_PIN 25
#endif
#ifndef RGB_LED_G_PIN
#define RGB_LED_G_PIN 27
#endif
#ifndef RGB_LED_B_PIN
#define RGB_LED_B_PIN 29
#endif
#elif defined(FYSETC_MINI_12864_REV_2_1)
#define NEOPIXEL_LED
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 25 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 3 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255)
#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#else
#error "Either FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0 or FYSETC_MINI_12864_REV_2_1 must be defined"
#endif
#if !defined(LED_USER_PRESET_STARTUP) && EITHER(FYSETC_MINI_12864_REV_2_0, FYSETC_MINI_12864_REV_2_1)
#error "LED_USER_PRESET_STARTUP must be enabled when using FYSETC_MINI_12864 REV 2.0 and later"
#endif
#elif ENABLED(NEWPANEL)
#define LCD_PINS_D4 23
#define LCD_PINS_D5 25
#define LCD_PINS_D6 27
#define LCD_PINS_D7 29
#if ENABLED(MINIPANEL)
#define DOGLCD_CS 25
#define DOGLCD_A0 27
#endif
#endif
#if ANY(VIKI2, miniVIKI)
#define DOGLCD_A0 16
#define KILL_PIN 51
#define STAT_LED_BLUE_PIN 29
#define STAT_LED_RED_PIN 23
#define DOGLCD_CS 17
#define DOGLCD_SCK 76 // SCK_PIN - These are required for DUE Hardware SPI
#define DOGLCD_SCK 76 // SCK_PIN - Required for DUE Hardware SPI
#define DOGLCD_MOSI 75 // MOSI_PIN
#define DOGLCD_MISO 74 // MISO_PIN
#endif
#endif // ULTRA_LCD
#if HAS_DRIVER(TMC2208)
@ -201,10 +240,8 @@
//
// M3/M4/M5 - Spindle/Laser Control
//
#if ENABLED(SPINDLE_LASER_ENABLE) && !PIN_EXISTS(SPINDLE_LASER_ENA)
#if HOTENDS < 3
#if HOTENDS < 3 && ENABLED(SPINDLE_LASER_ENABLE) && !PIN_EXISTS(SPINDLE_LASER_ENA)
#define SPINDLE_LASER_ENA_PIN 45 // Use E2 ENA
#define SPINDLE_LASER_PWM_PIN 12 // MUST BE HARDWARE PWM
#define SPINDLE_DIR_PIN 47 // Use E2 DIR
#endif
#endif

1
Marlin/src/pins/pins_RAMPS_RE_ARM.h
View file

@ -320,6 +320,7 @@
#define DOGLCD_MOSI P0_18
#define DOGLCD_CS P1_09 // use Ethernet connector for EXP1 cable signals
#define DOGLCD_A0 P1_14
#define FORCE_SOFT_SPI // required on a Re-ARM system
#else
#define DOGLCD_CS P0_26 // (63) J5-3 & AUX-2
#define DOGLCD_A0 P2_06 // (59) J3-8 & AUX-2

66
Marlin/src/pins/pins_RURAMPS4D_11.h
View file

@ -202,31 +202,24 @@
//
#if ENABLED(ULTRA_LCD)
#if EITHER(RADDS_DISPLAY, REPRAP_DISCOUNT_SMART_CONTROLLER)
#if ANY(RADDS_DISPLAY, REPRAP_DISCOUNT_SMART_CONTROLLER, REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
#define BEEPER_PIN 62
#define LCD_PINS_D4 48
#define LCD_PINS_D5 50
#define LCD_PINS_D6 52
#define LCD_PINS_D7 53
#define SD_DETECT_PIN 51
#endif
#if EITHER(RADDS_DISPLAY, REPRAP_DISCOUNT_SMART_CONTROLLER)
#define LCD_PINS_RS 63
#define LCD_PINS_ENABLE 64
#define LCD_PINS_D4 48
#define LCD_PINS_D5 50
#define LCD_PINS_D6 52
#define LCD_PINS_D7 53
#define SD_DETECT_PIN 51
#elif ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
#define BEEPER_PIN 62
#define LCD_PINS_RS 52
#define LCD_PINS_ENABLE 53
#define LCD_PINS_D4 48
#define LCD_PINS_D5 50
#define LCD_PINS_D6 52
#define LCD_PINS_D7 53
#define SD_DETECT_PIN 51
#elif HAS_SSD1306_OLED_I2C
@ -234,6 +227,47 @@
#define LCD_SDSS 10
#define SD_DETECT_PIN 51
#elif ENABLED(FYSETC_MINI_12864)
#define BEEPER_PIN 62
#define DOGLCD_CS 64
#define DOGLCD_A0 63
//#define FORCE_SOFT_SPI // Use this if default of hardware SPI causes problems
#define LCD_RESET_PIN 48 // Must be high or open for LCD to operate normally.
// Seems to work best if left open.
#define FYSETC_MINI_12864_REV_1_2
//#define FYSETC_MINI_12864_REV_2_0
//#define FYSETC_MINI_12864_REV_2_1
#if EITHER(FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0)
#define RGB_LED
#ifndef RGB_LED_R_PIN
#define RGB_LED_R_PIN 50 // D5
#endif
#ifndef RGB_LED_G_PIN
#define RGB_LED_G_PIN 52 // D6
#endif
#ifndef RGB_LED_B_PIN
#define RGB_LED_B_PIN 53 // D7
#endif
#elif defined(FYSETC_MINI_12864_REV_2_1)
#define NEOPIXEL_LED
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 50 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 3 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255)
#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#else
#error "Either FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0 or FYSETC_MINI_12864_REV_2_1 must be defined"
#endif
#if !defined(LED_USER_PRESET_STARTUP) && EITHER(FYSETC_MINI_12864_REV_2_0, FYSETC_MINI_12864_REV_2_1)
#error "LED_USER_PRESET_STARTUP must be enabled when using FYSETC_MINI_12864 REV 2.0 and later"
#endif
#elif ENABLED(SPARK_FULL_GRAPHICS)
//http://doku.radds.org/dokumentation/other-electronics/sparklcd/

66
Marlin/src/pins/pins_RURAMPS4D_13.h
View file

@ -188,31 +188,24 @@
//
#if ENABLED(ULTRA_LCD)
#if EITHER(RADDS_DISPLAY, REPRAP_DISCOUNT_SMART_CONTROLLER)
#if ANY(RADDS_DISPLAY, REPRAP_DISCOUNT_SMART_CONTROLLER, REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
#define BEEPER_PIN 62
#define LCD_PINS_D4 48
#define LCD_PINS_D5 50
#define LCD_PINS_D6 52
#define LCD_PINS_D7 53
#define SD_DETECT_PIN 51
#endif
#if EITHER(RADDS_DISPLAY, REPRAP_DISCOUNT_SMART_CONTROLLER)
#define LCD_PINS_RS 63
#define LCD_PINS_ENABLE 64
#define LCD_PINS_D4 48
#define LCD_PINS_D5 50
#define LCD_PINS_D6 52
#define LCD_PINS_D7 53
#define SD_DETECT_PIN 51
#elif ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
#define BEEPER_PIN 62
#define LCD_PINS_RS 52
#define LCD_PINS_ENABLE 53
#define LCD_PINS_D4 48
#define LCD_PINS_D5 50
#define LCD_PINS_D6 52
#define LCD_PINS_D7 53
#define SD_DETECT_PIN 51
#elif HAS_SSD1306_OLED_I2C
@ -220,6 +213,47 @@
#define LCD_SDSS 10
#define SD_DETECT_PIN 51
#elif ENABLED(FYSETC_MINI_12864)
#define BEEPER_PIN 62
#define DOGLCD_CS 64
#define DOGLCD_A0 63
//#define FORCE_SOFT_SPI // Use this if default of hardware SPI causes problems
#define LCD_RESET_PIN 48 // Must be high or open for LCD to operate normally.
// Seems to work best if left open.
#define FYSETC_MINI_12864_REV_1_2
//#define FYSETC_MINI_12864_REV_2_0
//#define FYSETC_MINI_12864_REV_2_1
#if EITHER(FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0)
#define RGB_LED
#ifndef RGB_LED_R_PIN
#define RGB_LED_R_PIN 50 // D5
#endif
#ifndef RGB_LED_G_PIN
#define RGB_LED_G_PIN 52 // D6
#endif
#ifndef RGB_LED_B_PIN
#define RGB_LED_B_PIN 53 // D7
#endif
#elif defined(FYSETC_MINI_12864_REV_2_1)
#define NEOPIXEL_LED
#define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
#define NEOPIXEL_PIN 50 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba)
#define NEOPIXEL_PIXELS 3 // Number of LEDs in the strip
#define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
#define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255)
#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup
#else
#error "Either FYSETC_MINI_12864_REV_1_2, FYSETC_MINI_12864_REV_2_0 or FYSETC_MINI_12864_REV_2_1 must be defined"
#endif
#if !defined(LED_USER_PRESET_STARTUP) && EITHER(FYSETC_MINI_12864_REV_2_0, FYSETC_MINI_12864_REV_2_1)
#error "LED_USER_PRESET_STARTUP must be enabled when using FYSETC_MINI_12864 REV 2.0 and later"
#endif
#elif ENABLED(MKS_MINI_12864)
#define ORIG_BEEPER_PIN 62