Apply FILAMENT_LOAD_UNLOAD_GCODES to example configs
This commit is contained in:
Scott Lahteine
parent
455592eee8
commit
8704e533da
|
|
@ -881,29 +881,38 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter length for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is loaded over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // Turn off nozzle if user doesn't change filament within this time limit in seconds
|
||||
#define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5 // Number of alert beeps before printer goes quiet
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change
|
||||
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
|
||||
//#define PARK_HEAD_ON_PAUSE // Go to filament change position on pause, return to print position on resume
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -881,29 +881,38 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter length for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is loaded over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // Turn off nozzle if user doesn't change filament within this time limit in seconds
|
||||
#define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5 // Number of alert beeps before printer goes quiet
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change
|
||||
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
|
||||
//#define PARK_HEAD_ON_PAUSE // Go to filament change position on pause, return to print position on resume
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -881,29 +881,38 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter length for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is loaded over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // Turn off nozzle if user doesn't change filament within this time limit in seconds
|
||||
#define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5 // Number of alert beeps before printer goes quiet
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change
|
||||
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
|
||||
//#define PARK_HEAD_ON_PAUSE // Go to filament change position on pause, return to print position on resume
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -881,29 +881,38 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter length for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is loaded over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // Turn off nozzle if user doesn't change filament within this time limit in seconds
|
||||
#define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5 // Number of alert beeps before printer goes quiet
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change
|
||||
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
|
||||
//#define PARK_HEAD_ON_PAUSE // Go to filament change position on pause, return to print position on resume
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -882,29 +882,38 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter length for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is loaded over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // Turn off nozzle if user doesn't change filament within this time limit in seconds
|
||||
#define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5 // Number of alert beeps before printer goes quiet
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change
|
||||
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
|
||||
//#define PARK_HEAD_ON_PAUSE // Go to filament change position on pause, return to print position on resume
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -881,29 +881,38 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter length for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is loaded over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // Turn off nozzle if user doesn't change filament within this time limit in seconds
|
||||
#define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5 // Number of alert beeps before printer goes quiet
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change
|
||||
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
|
||||
//#define PARK_HEAD_ON_PAUSE // Go to filament change position on pause, return to print position on resume
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -881,29 +881,38 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter length for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is loaded over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // Turn off nozzle if user doesn't change filament within this time limit in seconds
|
||||
#define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5 // Number of alert beeps before printer goes quiet
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change
|
||||
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
|
||||
//#define PARK_HEAD_ON_PAUSE // Go to filament change position on pause, return to print position on resume
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -881,29 +881,38 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter length for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is loaded over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // Turn off nozzle if user doesn't change filament within this time limit in seconds
|
||||
#define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5 // Number of alert beeps before printer goes quiet
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change
|
||||
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
|
||||
//#define PARK_HEAD_ON_PAUSE // Go to filament change position on pause, return to print position on resume
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -881,29 +881,38 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 1 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
//#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter length for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is loaded over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // Turn off nozzle if user doesn't change filament within this time limit in seconds
|
||||
#define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5 // Number of alert beeps before printer goes quiet
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change
|
||||
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
|
||||
//#define PARK_HEAD_ON_PAUSE // Go to filament change position on pause, return to print position on resume
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 1 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
//#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -881,29 +881,38 @@
|
|||
*/
|
||||
#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 4 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 420 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter length for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 8 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is loaded over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 120 // Turn off nozzle if user doesn't change filament within this time limit in seconds
|
||||
#define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 3 // Number of alert beeps before printer goes quiet
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change
|
||||
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
|
||||
#define PARK_HEAD_ON_PAUSE // Go to filament change position on pause, return to print position on resume
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 4 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 420 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 8 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 120 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 6 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -881,29 +881,38 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter length for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is loaded over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // Turn off nozzle if user doesn't change filament within this time limit in seconds
|
||||
#define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5 // Number of alert beeps before printer goes quiet
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change
|
||||
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
|
||||
//#define PARK_HEAD_ON_PAUSE // Go to filament change position on pause, return to print position on resume
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -881,29 +881,38 @@
|
|||
*/
|
||||
#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter length for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is loaded over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // Turn off nozzle if user doesn't change filament within this time limit in seconds
|
||||
#define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5 // Number of alert beeps before printer goes quiet
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change
|
||||
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
|
||||
#define PARK_HEAD_ON_PAUSE // Go to filament change position on pause, return to print position on resume
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -881,29 +881,38 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter length for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is loaded over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // Turn off nozzle if user doesn't change filament within this time limit in seconds
|
||||
#define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5 // Number of alert beeps before printer goes quiet
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change
|
||||
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
|
||||
//#define PARK_HEAD_ON_PAUSE // Go to filament change position on pause, return to print position on resume
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -882,29 +882,38 @@
|
|||
*/
|
||||
#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter length for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is loaded over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // Turn off nozzle if user doesn't change filament within this time limit in seconds
|
||||
#define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5 // Number of alert beeps before printer goes quiet
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change
|
||||
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
|
||||
//#define PARK_HEAD_ON_PAUSE // Go to filament change position on pause, return to print position on resume
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -881,29 +881,38 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter length for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is loaded over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // Turn off nozzle if user doesn't change filament within this time limit in seconds
|
||||
#define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5 // Number of alert beeps before printer goes quiet
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change
|
||||
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
|
||||
//#define PARK_HEAD_ON_PAUSE // Go to filament change position on pause, return to print position on resume
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -881,29 +881,38 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter length for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is loaded over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // Turn off nozzle if user doesn't change filament within this time limit in seconds
|
||||
#define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5 // Number of alert beeps before printer goes quiet
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change
|
||||
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
|
||||
//#define PARK_HEAD_ON_PAUSE // Go to filament change position on pause, return to print position on resume
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -882,29 +882,38 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter length for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is loaded over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // Turn off nozzle if user doesn't change filament within this time limit in seconds
|
||||
#define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5 // Number of alert beeps before printer goes quiet
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change
|
||||
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
|
||||
//#define PARK_HEAD_ON_PAUSE // Go to filament change position on pause, return to print position on resume
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -889,29 +889,38 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter length for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is loaded over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // Turn off nozzle if user doesn't change filament within this time limit in seconds
|
||||
#define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5 // Number of alert beeps before printer goes quiet
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change
|
||||
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
|
||||
//#define PARK_HEAD_ON_PAUSE // Go to filament change position on pause, return to print position on resume
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -881,29 +881,38 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter length for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is loaded over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // Turn off nozzle if user doesn't change filament within this time limit in seconds
|
||||
#define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5 // Number of alert beeps before printer goes quiet
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change
|
||||
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
|
||||
//#define PARK_HEAD_ON_PAUSE // Go to filament change position on pause, return to print position on resume
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -881,29 +881,38 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter length for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is loaded over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // Turn off nozzle if user doesn't change filament within this time limit in seconds
|
||||
#define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5 // Number of alert beeps before printer goes quiet
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change
|
||||
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
|
||||
//#define PARK_HEAD_ON_PAUSE // Go to filament change position on pause, return to print position on resume
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -870,29 +870,38 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter length for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is loaded over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // Turn off nozzle if user doesn't change filament within this time limit in seconds
|
||||
#define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5 // Number of alert beeps before printer goes quiet
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change
|
||||
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
|
||||
//#define PARK_HEAD_ON_PAUSE // Go to filament change position on pause, return to print position on resume
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -881,29 +881,38 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter length for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is loaded over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // Turn off nozzle if user doesn't change filament within this time limit in seconds
|
||||
#define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5 // Number of alert beeps before printer goes quiet
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change
|
||||
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
|
||||
//#define PARK_HEAD_ON_PAUSE // Go to filament change position on pause, return to print position on resume
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -881,29 +881,38 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter length for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is loaded over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // Turn off nozzle if user doesn't change filament within this time limit in seconds
|
||||
#define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5 // Number of alert beeps before printer goes quiet
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change
|
||||
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
|
||||
//#define PARK_HEAD_ON_PAUSE // Go to filament change position on pause, return to print position on resume
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -892,29 +892,38 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter length for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is loaded over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // Turn off nozzle if user doesn't change filament within this time limit in seconds
|
||||
#define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5 // Number of alert beeps before printer goes quiet
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change
|
||||
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
|
||||
//#define PARK_HEAD_ON_PAUSE // Go to filament change position on pause, return to print position on resume
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -881,29 +881,38 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 5 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 600 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter length for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 100 // Extrude filament length in mm after filament is loaded over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // Turn off nozzle if user doesn't change filament within this time limit in seconds
|
||||
#define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5 // Number of alert beeps before printer goes quiet
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change
|
||||
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
|
||||
//#define PARK_HEAD_ON_PAUSE // Go to filament change position on pause, return to print position on resume
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 5 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 600 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 100 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -883,29 +883,38 @@
|
|||
*/
|
||||
#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter length for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is loaded over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // Turn off nozzle if user doesn't change filament within this time limit in seconds
|
||||
#define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5 // Number of alert beeps before printer goes quiet
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change
|
||||
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
|
||||
//#define PARK_HEAD_ON_PAUSE // Go to filament change position on pause, return to print position on resume
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -883,29 +883,38 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter length for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is loaded over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // Turn off nozzle if user doesn't change filament within this time limit in seconds
|
||||
#define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5 // Number of alert beeps before printer goes quiet
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change
|
||||
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
|
||||
//#define PARK_HEAD_ON_PAUSE // Go to filament change position on pause, return to print position on resume
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -883,29 +883,38 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter length for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is loaded over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // Turn off nozzle if user doesn't change filament within this time limit in seconds
|
||||
#define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5 // Number of alert beeps before printer goes quiet
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change
|
||||
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
|
||||
//#define PARK_HEAD_ON_PAUSE // Go to filament change position on pause, return to print position on resume
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -883,29 +883,38 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter length for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is loaded over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // Turn off nozzle if user doesn't change filament within this time limit in seconds
|
||||
#define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5 // Number of alert beeps before printer goes quiet
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change
|
||||
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
|
||||
//#define PARK_HEAD_ON_PAUSE // Go to filament change position on pause, return to print position on resume
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -883,29 +883,38 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter length for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is loaded over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // Turn off nozzle if user doesn't change filament within this time limit in seconds
|
||||
#define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5 // Number of alert beeps before printer goes quiet
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change
|
||||
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
|
||||
//#define PARK_HEAD_ON_PAUSE // Go to filament change position on pause, return to print position on resume
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -888,29 +888,38 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter length for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is loaded over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // Turn off nozzle if user doesn't change filament within this time limit in seconds
|
||||
#define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5 // Number of alert beeps before printer goes quiet
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change
|
||||
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
|
||||
//#define PARK_HEAD_ON_PAUSE // Go to filament change position on pause, return to print position on resume
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -883,29 +883,38 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter length for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is loaded over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // Turn off nozzle if user doesn't change filament within this time limit in seconds
|
||||
#define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5 // Number of alert beeps before printer goes quiet
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change
|
||||
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
|
||||
//#define PARK_HEAD_ON_PAUSE // Go to filament change position on pause, return to print position on resume
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -881,29 +881,38 @@
|
|||
*/
|
||||
#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter length for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is loaded over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // Turn off nozzle if user doesn't change filament within this time limit in seconds
|
||||
#define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5 // Number of alert beeps before printer goes quiet
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change
|
||||
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
|
||||
#define PARK_HEAD_ON_PAUSE // Go to filament change position on pause, return to print position on resume
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -881,29 +881,38 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter length for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is loaded over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // Turn off nozzle if user doesn't change filament within this time limit in seconds
|
||||
#define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5 // Number of alert beeps before printer goes quiet
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change
|
||||
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
|
||||
//#define PARK_HEAD_ON_PAUSE // Go to filament change position on pause, return to print position on resume
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -881,29 +881,38 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter length for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is loaded over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // Turn off nozzle if user doesn't change filament within this time limit in seconds
|
||||
#define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5 // Number of alert beeps before printer goes quiet
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change
|
||||
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
|
||||
//#define PARK_HEAD_ON_PAUSE // Go to filament change position on pause, return to print position on resume
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
|
|
@ -882,29 +882,38 @@
|
|||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // Initial retract in mm
|
||||
// It is a short retract used immediately after print interrupt before move to filament exchange position
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // Unload filament feedrate in mm/s - filament unloading can be fast
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // Unload filament length from hotend in mm
|
||||
// Longer length for bowden printers to unload filament from whole bowden tube,
|
||||
// shorter length for printers without bowden to unload filament from extruder only,
|
||||
// 0 to disable unloading for manual unloading
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // Load filament length over hotend in mm
|
||||
// Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
|
||||
// Short or zero length for printers without bowden where loading is not used
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // Extrude filament feedrate in mm/s - must be slower than load feedrate
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // Extrude filament length in mm after filament is loaded over the hotend,
|
||||
// 0 to disable for manual extrusion
|
||||
// Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
|
||||
// or until outcoming filament color is not clear for filament color change
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // Turn off nozzle if user doesn't change filament within this time limit in seconds
|
||||
#define FILAMENT_CHANGE_NUMBER_OF_ALERT_BEEPS 5 // Number of alert beeps before printer goes quiet
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable to have stepper motors hold position during filament change
|
||||
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
|
||||
//#define PARK_HEAD_ON_PAUSE // Go to filament change position on pause, return to print position on resume
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_EXTRUDE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
|
|
|
|||
Loading…
Reference in a new issue