zaubentrucker/muele-marlin
1
0
Fork 0
Code Issues Pull requests Actions Packages Projects Releases Wiki Activity

Chamber Heater PID (#21156)

Browse source 
Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>
This commit is contained in:
Ken Sanislo 2021-02-24 16:26:51 -08:00 committed by Scott Lahteine
parent c051a2ecae
commit 8d05a823e9
15 changed files with 519 additions and 236 deletions
Show stats Download patch file Download diff file Expand all files Collapse all files

55
Marlin/Configuration.h
View file

@ -447,6 +447,10 @@
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_CHAMBER_RESIDENCY_TIME 10 // (seconds) Time to wait for chamber to "settle" in M191
#define TEMP_CHAMBER_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_CHAMBER_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
// Below this temperature the heater will be switched off
// because it probably indicates a broken thermistor wire.
#define HEATER_0_MINTEMP 5
@ -458,6 +462,7 @@
#define HEATER_6_MINTEMP 5
#define HEATER_7_MINTEMP 5
#define BED_MINTEMP 5
#define CHAMBER_MINTEMP 5
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
@ -471,6 +476,7 @@
#define HEATER_6_MAXTEMP 275
#define HEATER_7_MAXTEMP 275
#define BED_MAXTEMP 150
#define CHAMBER_MAXTEMP 60
//===========================================================================
//============================= PID Settings ================================
@ -544,7 +550,52 @@
// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
#endif // PIDTEMPBED
#if EITHER(PIDTEMP, PIDTEMPBED)
//===========================================================================
//==================== PID > Chamber Temperature Control ====================
//===========================================================================
/**
* PID Chamber Heating
*
* If this option is enabled set PID constants below.
* If this option is disabled, bang-bang will be used and CHAMBER_LIMIT_SWITCHING will enable
* hysteresis.
*
* The PID frequency will be the same as the extruder PWM.
* If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
* which is fine for driving a square wave into a resistive load and does not significantly
* impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 200W
* heater. If your configuration is significantly different than this and you don't understand
* the issues involved, don't use chamber PID until someone else verifies that your hardware works.
*/
//#define PIDTEMPCHAMBER
//#define CHAMBER_LIMIT_SWITCHING
/**
* Max Chamber Power
* Applies to all forms of chamber control (PID, bang-bang, and bang-bang with hysteresis).
* When set to any value below 255, enables a form of PWM to the chamber heater that acts like a divider
* so don't use it unless you are OK with PWM on your heater. (See the comment on enabling PIDTEMPCHAMBER)
*/
#define MAX_CHAMBER_POWER 255 // limits duty cycle to chamber heater; 255=full current
#if ENABLED(PIDTEMPCHAMBER)
#define MIN_CHAMBER_POWER 0
//#define PID_CHAMBER_DEBUG // Sends debug data to the serial port.
// Lasko "MyHeat Personal Heater" (200w) modified with a Fotek SSR-10DA to control only the heating element
// and placed inside the small Creality printer enclosure tent.
//
#define DEFAULT_chamberKp 37.04
#define DEFAULT_chamberKi 1.40
#define DEFAULT_chamberKd 655.17
// M309 P37.04 I1.04 D655.17
// FIND YOUR OWN: "M303 E-2 C8 S50" to run autotune on the chamber at 50 degreesC for 8 cycles.
#endif // PIDTEMPCHAMBER
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
//#define PID_DEBUG // Sends debug data to the serial port. Use 'M303 D' to toggle activation.
//#define PID_OPENLOOP // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
@ -1624,11 +1675,13 @@
#define PREHEAT_1_LABEL "PLA"
#define PREHEAT_1_TEMP_HOTEND 180
#define PREHEAT_1_TEMP_BED 70
#define PREHEAT_1_TEMP_CHAMBER 35
#define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255
#define PREHEAT_2_LABEL "ABS"
#define PREHEAT_2_TEMP_HOTEND 240
#define PREHEAT_2_TEMP_BED 110
#define PREHEAT_2_TEMP_CHAMBER 35
#define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255
/**

17
Marlin/Configuration_adv.h
View file

@ -143,12 +143,19 @@
//
// Heated Chamber options
//
#if DISABLED(PIDTEMPCHAMBER)
#define CHAMBER_CHECK_INTERVAL 5000 // (ms) Interval between checks in bang-bang control
#if ENABLED(CHAMBER_LIMIT_SWITCHING)
#define CHAMBER_HYSTERESIS 2 // (°C) Only set the relevant heater state when ABS(T-target) > CHAMBER_HYSTERESIS
#endif
#endif
#if TEMP_SENSOR_CHAMBER
#define CHAMBER_MINTEMP 5
#define CHAMBER_MAXTEMP 60
#define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target
//#define CHAMBER_LIMIT_SWITCHING
//#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin
// Make sure you define where your heater is connected, the following works on a BTT SKR 1.4 Turbo
// using the secondary tool heater output. (FAN1 by default).
//#define FAN1_PIN -1 // Remove the fan signal on pin P2_04 (SKR 1.4 Turbo specific)
//#define HEATER_CHAMBER_PIN P2_04 // Chamber heater on/off pin (HE1 connector on SKR 1.4 Turbo)
//#define HEATER_CHAMBER_INVERTING false
//#define CHAMBER_FAN // Enable a fan on the chamber

2
Marlin/src/core/language.h
View file

@ -221,7 +221,7 @@
// temperature.cpp strings
#define STR_PID_AUTOTUNE_START "PID Autotune start"
#define STR_PID_BAD_EXTRUDER_NUM "PID Autotune failed! Bad extruder number"
#define STR_PID_BAD_HEATER_ID "PID Autotune failed! Bad heater id"
#define STR_PID_TEMP_TOO_HIGH "PID Autotune failed! Temperature too high"
#define STR_PID_TIMEOUT "PID Autotune failed! timeout"
#define STR_BIAS " bias: "

13
Marlin/src/feature/leds/printer_event_leds.cpp
View file

@ -77,6 +77,19 @@ PrinterEventLEDs printerEventLEDs;
pel_set_rgb(red, 0, 255);
}
}
#endif
#if HAS_HEATED_CHAMBER
void PrinterEventLEDs::onChamberHeating(const float &start, const float &current, const float &target) {
const uint8_t green = pel_intensity(start, current, target);
if (green != old_intensity) {
old_intensity = green;
pel_set_rgb(255, green, 255);
}
}
#endif
#endif // PRINTER_EVENT_LEDS

7
Marlin/src/feature/leds/printer_event_leds.h
View file

@ -55,7 +55,12 @@ public:
static void onBedHeating(const float &start, const float &current, const float &target);
#endif
#if HAS_TEMP_HOTEND || HAS_HEATED_BED
#if HAS_HEATED_CHAMBER
static inline LEDColor onChamberHeatingStart() { old_intensity = 127; return leds.get_color(); }
static void onChamberHeating(const float &start, const float &current, const float &target);
#endif
#if HAS_TEMP_HOTEND || HAS_HEATED_BED || HAS_HEATED_CHAMBER
static inline void onHeatingDone() { leds.set_white(); }
static inline void onPidTuningDone(LEDColor c) { leds.set_color(c); }
#endif

48
Marlin/src/gcode/config/M309.cpp Normal file
View file

@ -0,0 +1,48 @@
/**
* Marlin 3D Printer Firmware
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <https://www.gnu.org/licenses/>.
*
*/
#include "../../inc/MarlinConfig.h"
#if ENABLED(PIDTEMPCHAMBER)
#include "../gcode.h"
#include "../../module/temperature.h"
/**
* M309 - Set and/or Report the current Chamber PID values
*
* P<pval> - Set the P value
* I<ival> - Set the I value
* D<dval> - Set the D value
*/
void GcodeSuite::M309() {
if (parser.seen('P')) thermalManager.temp_chamber.pid.Kp = parser.value_float();
if (parser.seen('I')) thermalManager.temp_chamber.pid.Ki = scalePID_i(parser.value_float());
if (parser.seen('D')) thermalManager.temp_chamber.pid.Kd = scalePID_d(parser.value_float());
SERIAL_ECHO_START();
SERIAL_ECHOLNPAIR(" p:", thermalManager.temp_chamber.pid.Kp,
" i:", unscalePID_i(thermalManager.temp_chamber.pid.Ki),
" d:", unscalePID_d(thermalManager.temp_chamber.pid.Kd));
}
#endif // PIDTEMPCHAMBER

4
Marlin/src/gcode/gcode.cpp
View file

@ -682,6 +682,10 @@ void GcodeSuite::process_parsed_command(const bool no_ok/*=false*/) {
case 304: M304(); break; // M304: Set bed PID parameters
#endif
#if ENABLED(PIDTEMPCHAMBER)
case 309: M309(); break; // M309: Set chamber PID parameters
#endif
#if ENABLED(PHOTO_GCODE)
case 240: M240(); break; // M240: Trigger a camera
#endif

3
Marlin/src/gcode/gcode.h
View file

@ -197,6 +197,7 @@
* M303 - PID relay autotune S<temperature> sets the target temperature. Default 150C. (Requires PIDTEMP)
* M304 - Set bed PID parameters P I and D. (Requires PIDTEMPBED)
* M305 - Set user thermistor parameters R T and P. (Requires TEMP_SENSOR_x 1000)
* M309 - Set chamber PID parameters P I and D. (Requires PIDTEMPCHAMBER)
* M350 - Set microstepping mode. (Requires digital microstepping pins.)
* M351 - Toggle MS1 MS2 pins directly. (Requires digital microstepping pins.)
* M355 - Set Case Light on/off and set brightness. (Requires CASE_LIGHT_PIN)
@ -711,6 +712,8 @@ private:
TERN_(HAS_USER_THERMISTORS, static void M305());
TERN_(PIDTEMPCHAMBER, static void M309());
#if HAS_MICROSTEPS
static void M350();
static void M351();

37
Marlin/src/gcode/temp/M303.cpp
View file

@ -40,19 +40,15 @@
* C<cycles> Number of times to repeat the procedure. (Minimum: 3, Default: 5)
* U<bool> Flag to apply the result to the current PID values
*
* With PID_DEBUG:
* With PID_DEBUG, PID_BED_DEBUG, or PID_CHAMBER_DEBUG:
* D Toggle PID debugging and EXIT without further action.
*/
#if ENABLED(PID_DEBUG)
bool pid_debug_flag = 0;
#endif
void GcodeSuite::M303() {
#if ENABLED(PID_DEBUG)
#if ANY(PID_DEBUG, PID_BED_DEBUG, PID_CHAMBER_DEBUG)
if (parser.seen('D')) {
pid_debug_flag = !pid_debug_flag;
thermalManager.pid_debug_flag ^= true;
SERIAL_ECHO_START();
SERIAL_ECHOPGM("PID Debug ");
serialprintln_onoff(pid_debug_flag);
@ -60,25 +56,34 @@ void GcodeSuite::M303() {
}
#endif
#define SI TERN(PIDTEMPBED, H_BED, H_E0)
#define EI TERN(PIDTEMP, HOTENDS - 1, H_BED)
const heater_id_t e = (heater_id_t)parser.intval('E');
if (!WITHIN(e, SI, EI)) {
SERIAL_ECHOLNPGM(STR_PID_BAD_EXTRUDER_NUM);
TERN_(EXTENSIBLE_UI, ExtUI::onPidTuning(ExtUI::result_t::PID_BAD_EXTRUDER_NUM));
return;
const heater_id_t hid = (heater_id_t)parser.intval('E');
int16_t default_temp;
switch (hid) {
#if ENABLED(PIDTEMP)
case 0 ... HOTENDS - 1: default_temp = PREHEAT_1_TEMP_HOTEND; break;
#endif
#if ENABLED(PIDTEMPBED)
case H_BED: default_temp = PREHEAT_1_TEMP_BED; break;
#endif
#if ENABLED(PIDTEMPCHAMBER)
case H_CHAMBER: default_temp = PREHEAT_1_TEMP_CHAMBER; break;
#endif
default:
SERIAL_ECHOLNPGM(STR_PID_BAD_HEATER_ID);
TERN_(EXTENSIBLE_UI, ExtUI::onPidTuning(ExtUI::result_t::PID_BAD_EXTRUDER_NUM));
return;
}
const int16_t temp = parser.celsiusval('S', default_temp);
const int c = parser.intval('C', 5);
const bool u = parser.boolval('U');
const int16_t temp = parser.celsiusval('S', e < 0 ? PREHEAT_1_TEMP_BED : PREHEAT_1_TEMP_HOTEND);
#if DISABLED(BUSY_WHILE_HEATING)
KEEPALIVE_STATE(NOT_BUSY);
#endif
LCD_MESSAGEPGM(MSG_PID_AUTOTUNE);
thermalManager.PID_autotune(temp, e, c, u);
thermalManager.PID_autotune(temp, hid, c, u);
ui.reset_status();
}

21
Marlin/src/inc/Conditionals_post.h
View file

@ -1992,27 +1992,31 @@
#define BED_OVERSHOOT 10
#endif
#define BED_MAX_TARGET (BED_MAXTEMP - (BED_OVERSHOOT))
#else
#undef PIDTEMPBED
#endif
#if HAS_HEATED_BED || HAS_TEMP_CHAMBER
#define BED_OR_CHAMBER 1
#endif
#if HAS_TEMP_HOTEND || BED_OR_CHAMBER || HAS_TEMP_PROBE
#define HAS_TEMP_SENSOR 1
#endif
#if HAS_TEMP_CHAMBER && PIN_EXISTS(HEATER_CHAMBER)
#define HAS_HEATED_CHAMBER 1
#ifndef CHAMBER_OVERSHOOT
#define CHAMBER_OVERSHOOT 10
#endif
#define CHAMBER_MAX_TARGET (CHAMBER_MAXTEMP - (CHAMBER_OVERSHOOT))
#else
#undef PIDTEMPCHAMBER
#endif
// PID heating
#if !HAS_HEATED_BED
#undef PIDTEMPBED
#endif
#if EITHER(PIDTEMP, PIDTEMPBED)
#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
#define HAS_PID_HEATING 1
#endif
#if BOTH(PIDTEMP, PIDTEMPBED)
#define HAS_PID_FOR_BOTH 1
#endif
// Thermal protection
#if BOTH(HAS_HEATED_BED, THERMAL_PROTECTION_BED)
@ -2346,6 +2350,9 @@
* Heated chamber requires settings
*/
#if HAS_HEATED_CHAMBER
#ifndef MIN_CHAMBER_POWER
#define MIN_CHAMBER_POWER 0
#endif
#ifndef MAX_CHAMBER_POWER
#define MAX_CHAMBER_POWER 255
#endif

7
Marlin/src/inc/SanityCheck.h
View file

@ -1203,6 +1203,13 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
#error "To use BED_LIMIT_SWITCHING you must disable PIDTEMPBED."
#endif
/**
* Chamber Heating Options - PID vs Limit Switching
*/
#if BOTH(PIDTEMPCHAMBER, CHAMBER_LIMIT_SWITCHING)
#error "To use CHAMBER_LIMIT_SWITCHING you must disable PIDTEMPCHAMBER."
#endif
/**
* Kinematics
*/

79
Marlin/src/lcd/menu/menu_advanced.cpp
View file

@ -177,18 +177,25 @@ void menu_backlash();
#if ENABLED(PIDTEMPBED)
int16_t autotune_temp_bed = PREHEAT_1_TEMP_BED;
#endif
#if ENABLED(PIDTEMPCHAMBER)
int16_t autotune_temp_chamber = PREHEAT_1_TEMP_CHAMBER;
#endif
#include "../../gcode/queue.h"
void _lcd_autotune(const int16_t e) {
void _lcd_autotune(const heater_id_t hid) {
char cmd[30];
sprintf_P(cmd, PSTR("M303 U1 E%i S%i"), e,
#if HAS_PID_FOR_BOTH
e < 0 ? autotune_temp_bed : autotune_temp[e]
#else
TERN(PIDTEMPBED, autotune_temp_bed, autotune_temp[e])
int16_t tune_temp;
switch (hid) {
#if ENABLED(PIDTEMPBED)
case H_BED: tune_temp = autotune_temp_bed; break;
#endif
);
#if ENABLED(PIDTEMPCHAMBER)
case H_CHAMBER: tune_temp = autotune_temp_chamber; break;
#endif
default: tune_temp = autotune_temp[hid]; break;
}
sprintf_P(cmd, PSTR("M303 U1 E%i S%i"), hid, tune_temp);
queue.inject(cmd);
ui.return_to_status();
}
@ -225,7 +232,7 @@ void menu_backlash();
#if ENABLED(PID_AUTOTUNE_MENU)
#define DEFINE_PIDTEMP_FUNCS(N) \
_DEFINE_PIDTEMP_BASE_FUNCS(N); \
void lcd_autotune_callback_E##N() { _lcd_autotune(N); }
void lcd_autotune_callback_E##N() { _lcd_autotune(heater_id_t(N)); }
#else
#define DEFINE_PIDTEMP_FUNCS(N) _DEFINE_PIDTEMP_BASE_FUNCS(N);
#endif
@ -269,56 +276,70 @@ void menu_backlash();
//
#if ENABLED(PID_EDIT_MENU)
#define __PID_BASE_MENU_ITEMS(N) \
raw_Ki = unscalePID_i(TERN(PID_BED_MENU_SECTION, thermalManager.temp_bed.pid.Ki, PID_PARAM(Ki, N))); \
raw_Kd = unscalePID_d(TERN(PID_BED_MENU_SECTION, thermalManager.temp_bed.pid.Kd, PID_PARAM(Kd, N))); \
EDIT_ITEM_FAST_N(float41sign, N, MSG_PID_P_E, &TERN(PID_BED_MENU_SECTION, thermalManager.temp_bed.pid.Kp, PID_PARAM(Kp, N)), 1, 9990); \
#define _PID_EDIT_ITEMS_TMPL(N,T) \
raw_Ki = unscalePID_i(T.pid.Ki); \
raw_Kd = unscalePID_d(T.pid.Kd); \
EDIT_ITEM_FAST_N(float41sign, N, MSG_PID_P_E, &T.pid.Kp, 1, 9990); \
EDIT_ITEM_FAST_N(float52sign, N, MSG_PID_I_E, &raw_Ki, 0.01f, 9990, []{ copy_and_scalePID_i(N); }); \
EDIT_ITEM_FAST_N(float41sign, N, MSG_PID_D_E, &raw_Kd, 1, 9990, []{ copy_and_scalePID_d(N); })
#define __PID_HOTEND_MENU_ITEMS(N) \
raw_Ki = unscalePID_i(PID_PARAM(Ki, N)); \
raw_Kd = unscalePID_d(PID_PARAM(Kd, N)); \
EDIT_ITEM_FAST_N(float41sign, N, MSG_PID_P_E, &PID_PARAM(Kp, N), 1, 9990); \
EDIT_ITEM_FAST_N(float52sign, N, MSG_PID_I_E, &raw_Ki, 0.01f, 9990, []{ copy_and_scalePID_i(N); }); \
EDIT_ITEM_FAST_N(float41sign, N, MSG_PID_D_E, &raw_Kd, 1, 9990, []{ copy_and_scalePID_d(N); })
#if ENABLED(PID_EXTRUSION_SCALING)
#define _PID_BASE_MENU_ITEMS(N) \
__PID_BASE_MENU_ITEMS(N); \
#define _PID_HOTEND_MENU_ITEMS(N) \
__PID_HOTEND_MENU_ITEMS(N); \
EDIT_ITEM_N(float4, N, MSG_PID_C_E, &PID_PARAM(Kc, N), 1, 9990)
#else
#define _PID_BASE_MENU_ITEMS(N) __PID_BASE_MENU_ITEMS(N)
#define _PID_HOTEND_MENU_ITEMS(N) __PID_HOTEND_MENU_ITEMS(N)
#endif
#if ENABLED(PID_FAN_SCALING)
#define _PID_EDIT_MENU_ITEMS(N) \
_PID_BASE_MENU_ITEMS(N); \
#define _HOTEND_PID_EDIT_MENU_ITEMS(N) \
_PID_HOTEND_MENU_ITEMS(N); \
EDIT_ITEM_N(float4, N, MSG_PID_F_E, &PID_PARAM(Kf, N), 1, 9990)
#else
#define _PID_EDIT_MENU_ITEMS(N) _PID_BASE_MENU_ITEMS(N)
#define _HOTEND_PID_EDIT_MENU_ITEMS(N) _PID_HOTEND_MENU_ITEMS(N)
#endif
#else
#define _PID_EDIT_MENU_ITEMS(N) NOOP
#define _HOTEND_PID_EDIT_MENU_ITEMS(N) NOOP
#endif
#if ENABLED(PID_AUTOTUNE_MENU)
#define PID_EDIT_MENU_ITEMS(N) \
_PID_EDIT_MENU_ITEMS(N); \
EDIT_ITEM_FAST_N(int3, N, MSG_PID_AUTOTUNE_E, &autotune_temp[N], 150, thermalManager.heater_maxtemp[N] - HOTEND_OVERSHOOT, []{ _lcd_autotune(MenuItemBase::itemIndex); });
#define HOTEND_PID_EDIT_MENU_ITEMS(N) \
_HOTEND_PID_EDIT_MENU_ITEMS(N); \
EDIT_ITEM_FAST_N(int3, N, MSG_PID_AUTOTUNE_E, &autotune_temp[N], 150, thermalManager.heater_maxtemp[N] - HOTEND_OVERSHOOT, []{ _lcd_autotune(heater_id_t(MenuItemBase::itemIndex)); });
#else
#define PID_EDIT_MENU_ITEMS(N) _PID_EDIT_MENU_ITEMS(N);
#define HOTEND_PID_EDIT_MENU_ITEMS(N) _HOTEND_PID_EDIT_MENU_ITEMS(N);
#endif
PID_EDIT_MENU_ITEMS(0);
HOTEND_PID_EDIT_MENU_ITEMS(0);
#if ENABLED(PID_PARAMS_PER_HOTEND)
REPEAT_S(1, HOTENDS, PID_EDIT_MENU_ITEMS)
REPEAT_S(1, HOTENDS, HOTEND_PID_EDIT_MENU_ITEMS)
#endif
#if ENABLED(PIDTEMPBED)
#if ENABLED(PID_EDIT_MENU)
#define PID_BED_MENU_SECTION
__PID_BASE_MENU_ITEMS(-1);
#undef PID_BED_MENU_SECTION
_PID_EDIT_ITEMS_TMPL(H_BED, thermalManager.temp_bed);
#endif
#if ENABLED(PID_AUTOTUNE_MENU)
EDIT_ITEM_FAST_N(int3, -1, MSG_PID_AUTOTUNE_E, &autotune_temp_bed, PREHEAT_1_TEMP_BED, BED_MAX_TARGET, []{ _lcd_autotune(-1); });
EDIT_ITEM_FAST_N(int3, H_BED, MSG_PID_AUTOTUNE_E, &autotune_temp_bed, PREHEAT_1_TEMP_BED, BED_MAX_TARGET, []{ _lcd_autotune(H_BED); });
#endif
#endif
#if ENABLED(PIDTEMPCHAMBER)
#if ENABLED(PID_EDIT_MENU)
_PID_EDIT_ITEMS_TMPL(H_CHAMBER, thermalManager.temp_chamber);
#endif
#if ENABLED(PID_AUTOTUNE_MENU)
EDIT_ITEM_FAST_N(int3, H_CHAMBER, MSG_PID_AUTOTUNE_E, &autotune_temp_chamber, PREHEAT_1_TEMP_CHAMBER, CHAMBER_MAX_TARGET, []{ _lcd_autotune(H_CHAMBER); });
#endif
#endif

61
Marlin/src/module/settings.cpp
View file

@ -318,6 +318,11 @@ typedef struct SettingsDataStruct {
//
PID_t bedPID; // M304 PID / M303 E-1 U
//
// PIDTEMPCHAMBER
//
PID_t chamberPID; // M309 PID / M303 E-2 U
//
// User-defined Thermistors
//
@ -926,6 +931,25 @@ void MarlinSettings::postprocess() {
EEPROM_WRITE(bed_pid);
}
//
// PIDTEMPCHAMBER
//
{
_FIELD_TEST(chamberPID);
const PID_t chamber_pid = {
#if DISABLED(PIDTEMPCHAMBER)
NAN, NAN, NAN
#else
// Store the unscaled PID values
thermalManager.temp_chamber.pid.Kp,
unscalePID_i(thermalManager.temp_chamber.pid.Ki),
unscalePID_d(thermalManager.temp_chamber.pid.Kd)
#endif
};
EEPROM_WRITE(chamber_pid);
}
//
// User-defined Thermistors
//
@ -1787,6 +1811,22 @@ void MarlinSettings::postprocess() {
#endif
}
//
// Heated Chamber PID
//
{
PID_t pid;
EEPROM_READ(pid);
#if ENABLED(PIDTEMPCHAMBER)
if (!validating && !isnan(pid.Kp)) {
// Scale PID values since EEPROM values are unscaled
thermalManager.temp_chamber.pid.Kp = pid.Kp;
thermalManager.temp_chamber.pid.Ki = scalePID_i(pid.Ki);
thermalManager.temp_chamber.pid.Kd = scalePID_d(pid.Kd);
}
#endif
}
//
// User-defined Thermistors
//
@ -2811,6 +2851,16 @@ void MarlinSettings::reset() {
thermalManager.temp_bed.pid.Kd = scalePID_d(DEFAULT_bedKd);
#endif
//
// Heated Chamber PID
//
#if ENABLED(PIDTEMPCHAMBER)
thermalManager.temp_chamber.pid.Kp = DEFAULT_chamberKp;
thermalManager.temp_chamber.pid.Ki = scalePID_i(DEFAULT_chamberKi);
thermalManager.temp_chamber.pid.Kd = scalePID_d(DEFAULT_chamberKd);
#endif
//
// User-Defined Thermistors
//
@ -3386,7 +3436,16 @@ void MarlinSettings::reset() {
);
#endif
#endif // PIDTEMP || PIDTEMPBED
#if ENABLED(PIDTEMPCHAMBER)
CONFIG_ECHO_START();
SERIAL_ECHOLNPAIR(
" M309 P", thermalManager.temp_chamber.pid.Kp
, " I", unscalePID_i(thermalManager.temp_chamber.pid.Ki)
, " D", unscalePID_d(thermalManager.temp_chamber.pid.Kd)
);
#endif
#endif // PIDTEMP || PIDTEMPBED || PIDTEMPCHAMBER
#if HAS_USER_THERMISTORS
CONFIG_ECHO_HEADING("User thermistors:");

380
Marlin/src/module/temperature.cpp
View file

@ -371,10 +371,8 @@ const char str_t_thermal_runaway[] PROGMEM = STR_T_THERMAL_RUNAWAY,
#ifdef CHAMBER_MAXTEMP
int16_t Temperature::maxtemp_raw_CHAMBER = TEMP_SENSOR_CHAMBER_RAW_HI_TEMP;
#endif
#if WATCH_CHAMBER
chamber_watch_t Temperature::watch_chamber{0};
#endif
millis_t Temperature::next_chamber_check_ms;
TERN_(WATCH_CHAMBER, chamber_watch_t Temperature::watch_chamber{0});
IF_DISABLED(PIDTEMPCHAMBER, millis_t Temperature::next_chamber_check_ms);
#endif // HAS_HEATED_CHAMBER
#endif // HAS_TEMP_CHAMBER
@ -382,11 +380,6 @@ const char str_t_thermal_runaway[] PROGMEM = STR_T_THERMAL_RUNAWAY,
probe_info_t Temperature::temp_probe; // = { 0 }
#endif
// Initialized by settings.load()
#if ENABLED(PIDTEMP)
//hotend_pid_t Temperature::pid[HOTENDS];
#endif
#if ENABLED(PREVENT_COLD_EXTRUSION)
bool Temperature::allow_cold_extrude = false;
int16_t Temperature::extrude_min_temp = EXTRUDE_MINTEMP;
@ -485,41 +478,44 @@ volatile bool Temperature::raw_temps_ready = false;
millis_t next_temp_ms = millis(), t1 = next_temp_ms, t2 = next_temp_ms;
long t_high = 0, t_low = 0;
long bias, d;
PID_t tune_pid = { 0, 0, 0 };
float maxT = 0, minT = 10000;
const bool isbed = (heater_id == H_BED);
const bool ischamber = (heater_id == H_CHAMBER);
#if HAS_PID_FOR_BOTH
#define GHV(B,H) (isbed ? (B) : (H))
#define SHV(B,H) do{ if (isbed) temp_bed.soft_pwm_amount = B; else temp_hotend[heater_id].soft_pwm_amount = H; }while(0)
#define ONHEATINGSTART() (isbed ? printerEventLEDs.onBedHeatingStart() : printerEventLEDs.onHotendHeatingStart())
#define ONHEATING(S,C,T) (isbed ? printerEventLEDs.onBedHeating(S,C,T) : printerEventLEDs.onHotendHeating(S,C,T))
#elif ENABLED(PIDTEMPBED)
#define GHV(B,H) B
#define SHV(B,H) (temp_bed.soft_pwm_amount = B)
#define ONHEATINGSTART() printerEventLEDs.onBedHeatingStart()
#define ONHEATING(S,C,T) printerEventLEDs.onBedHeating(S,C,T)
#if ENABLED(PIDTEMPCHAMBER)
#define C_TERN(T,A,B) ((T) ? (A) : (B))
#else
#define GHV(B,H) H
#define SHV(B,H) (temp_hotend[heater_id].soft_pwm_amount = H)
#define ONHEATINGSTART() printerEventLEDs.onHotendHeatingStart()
#define ONHEATING(S,C,T) printerEventLEDs.onHotendHeating(S,C,T)
#define C_TERN(T,A,B) (B)
#endif
#define WATCH_PID BOTH(WATCH_BED, PIDTEMPBED) || BOTH(WATCH_HOTENDS, PIDTEMP)
#if ENABLED(PIDTEMPBED)
#define B_TERN(T,A,B) ((T) ? (A) : (B))
#else
#define B_TERN(T,A,B) (B)
#endif
#define GHV(C,B,H) C_TERN(ischamber, C, B_TERN(isbed, B, H))
#define SHV(V) C_TERN(ischamber, temp_chamber.soft_pwm_amount = V, B_TERN(isbed, temp_bed.soft_pwm_amount = V, temp_hotend[heater_id].soft_pwm_amount = V))
#define ONHEATINGSTART() C_TERN(ischamber, printerEventLEDs.onChamberHeatingStart(), B_TERN(isbed, printerEventLEDs.onBedHeatingStart(), printerEventLEDs.onHotendHeatingStart()))
#define ONHEATING(S,C,T) C_TERN(ischamber, printerEventLEDs.onChamberHeating(S,C,T), B_TERN(isbed, printerEventLEDs.onBedHeating(S,C,T), printerEventLEDs.onHotendHeating(S,C,T)))
#define WATCH_PID BOTH(WATCH_CHAMBER, PIDTEMPCHAMBER) || BOTH(WATCH_BED, PIDTEMPBED) || BOTH(WATCH_HOTENDS, PIDTEMP)
#if WATCH_PID
#if ALL(THERMAL_PROTECTION_HOTENDS, PIDTEMP, THERMAL_PROTECTION_BED, PIDTEMPBED)
#define GTV(B,H) (isbed ? (B) : (H))
#elif BOTH(THERMAL_PROTECTION_HOTENDS, PIDTEMP)
#define GTV(B,H) (H)
#if BOTH(THERMAL_PROTECTION_CHAMBER, PIDTEMPCHAMBER)
#define C_GTV(T,A,B) ((T) ? (A) : (B))
#else
#define GTV(B,H) (B)
#define C_GTV(T,A,B) (B)
#endif
const uint16_t watch_temp_period = GTV(WATCH_BED_TEMP_PERIOD, WATCH_TEMP_PERIOD);
const uint8_t watch_temp_increase = GTV(WATCH_BED_TEMP_INCREASE, WATCH_TEMP_INCREASE);
const float watch_temp_target = target - float(watch_temp_increase + GTV(TEMP_BED_HYSTERESIS, TEMP_HYSTERESIS) + 1);
#if BOTH(THERMAL_PROTECTION_BED, PIDTEMPBED)
#define B_GTV(T,A,B) ((T) ? (A) : (B))
#else
#define B_GTV(T,A,B) (B)
#endif
#define GTV(C,B,H) C_GTV(ischamber, C, B_GTV(isbed, B, H))
const uint16_t watch_temp_period = GTV(WATCH_CHAMBER_TEMP_PERIOD, WATCH_BED_TEMP_PERIOD, WATCH_TEMP_PERIOD);
const uint8_t watch_temp_increase = GTV(WATCH_CHAMBER_TEMP_INCREASE, WATCH_BED_TEMP_INCREASE, WATCH_TEMP_INCREASE);
const float watch_temp_target = target - float(watch_temp_increase + GTV(TEMP_CHAMBER_HYSTERESIS, TEMP_BED_HYSTERESIS, TEMP_HYSTERESIS) + 1);
millis_t temp_change_ms = next_temp_ms + SEC_TO_MS(watch_temp_period);
float next_watch_temp = 0.0;
bool heated = false;
@ -527,7 +523,7 @@ volatile bool Temperature::raw_temps_ready = false;
TERN_(HAS_AUTO_FAN, next_auto_fan_check_ms = next_temp_ms + 2500UL);
if (target > GHV(BED_MAX_TARGET, temp_range[heater_id].maxtemp - HOTEND_OVERSHOOT)) {
if (target > GHV(CHAMBER_MAX_TARGET, BED_MAX_TARGET, temp_range[heater_id].maxtemp - HOTEND_OVERSHOOT)) {
SERIAL_ECHOLNPGM(STR_PID_TEMP_TOO_HIGH);
TERN_(EXTENSIBLE_UI, ExtUI::onPidTuning(ExtUI::result_t::PID_TEMP_TOO_HIGH));
return;
@ -538,10 +534,11 @@ volatile bool Temperature::raw_temps_ready = false;
disable_all_heaters();
TERN_(AUTO_POWER_CONTROL, powerManager.power_on());
SHV(bias = d = (MAX_BED_POWER) >> 1, bias = d = (PID_MAX) >> 1);
long bias = GHV(MAX_CHAMBER_POWER, MAX_BED_POWER, PID_MAX) >> 1, d = bias;
SHV(bias);
#if ENABLED(PRINTER_EVENT_LEDS)
const float start_temp = GHV(temp_bed.celsius, temp_hotend[heater_id].celsius);
const float start_temp = GHV(temp_chamber.celsius, temp_bed.celsius, temp_hotend[heater_id].celsius);
LEDColor color = ONHEATINGSTART();
#endif
@ -557,7 +554,7 @@ volatile bool Temperature::raw_temps_ready = false;
updateTemperaturesFromRawValues();
// Get the current temperature and constrain it
current_temp = GHV(temp_bed.celsius, temp_hotend[heater_id].celsius);
current_temp = GHV(temp_chamber.celsius, temp_bed.celsius, temp_hotend[heater_id].celsius);
NOLESS(maxT, current_temp);
NOMORE(minT, current_temp);
@ -572,67 +569,46 @@ volatile bool Temperature::raw_temps_ready = false;
}
#endif
if (heating && current_temp > target) {
if (ELAPSED(ms, t2 + 5000UL)) {
heating = false;
SHV((bias - d) >> 1, (bias - d) >> 1);
t1 = ms;
t_high = t1 - t2;
maxT = target;
}
if (heating && current_temp > target && ELAPSED(ms, t2 + 5000UL)) {
heating = false;
SHV((bias - d) >> 1);
t1 = ms;
t_high = t1 - t2;
maxT = target;
}
if (!heating && current_temp < target) {
if (ELAPSED(ms, t1 + 5000UL)) {
heating = true;
t2 = ms;
t_low = t2 - t1;
if (cycles > 0) {
const long max_pow = GHV(MAX_BED_POWER, PID_MAX);
bias += (d * (t_high - t_low)) / (t_low + t_high);
LIMIT(bias, 20, max_pow - 20);
d = (bias > max_pow >> 1) ? max_pow - 1 - bias : bias;
if (!heating && current_temp < target && ELAPSED(ms, t1 + 5000UL)) {
heating = true;
t2 = ms;
t_low = t2 - t1;
if (cycles > 0) {
const long max_pow = GHV(MAX_CHAMBER_POWER, MAX_BED_POWER, PID_MAX);
bias += (d * (t_high - t_low)) / (t_low + t_high);
LIMIT(bias, 20, max_pow - 20);
d = (bias > max_pow >> 1) ? max_pow - 1 - bias : bias;
SERIAL_ECHOPAIR(STR_BIAS, bias, STR_D_COLON, d, STR_T_MIN, minT, STR_T_MAX, maxT);
if (cycles > 2) {
const float Ku = (4.0f * d) / (float(M_PI) * (maxT - minT) * 0.5f),
Tu = float(t_low + t_high) * 0.001f,
pf = isbed ? 0.2f : 0.6f,
df = isbed ? 1.0f / 3.0f : 1.0f / 8.0f;
SERIAL_ECHOPAIR(STR_BIAS, bias, STR_D_COLON, d, STR_T_MIN, minT, STR_T_MAX, maxT);
if (cycles > 2) {
const float Ku = (4.0f * d) / (float(M_PI) * (maxT - minT) * 0.5f),
Tu = float(t_low + t_high) * 0.001f,
pf = ischamber ? 0.2f : (isbed ? 0.2f : 0.6f),
df = ischamber ? 1.0f / 3.0f : (isbed ? 1.0f / 3.0f : 1.0f / 8.0f);
SERIAL_ECHOPAIR(STR_KU, Ku, STR_TU, Tu);
if (isbed) { // Do not remove this otherwise PID autotune won't work right for the bed!
tune_pid.Kp = Ku * 0.2f;
tune_pid.Ki = 2 * tune_pid.Kp / Tu;
tune_pid.Kd = tune_pid.Kp * Tu / 3;
SERIAL_ECHOLNPGM("\n" " No overshoot"); // Works far better for the bed. Classic and some have bad ringing.
SERIAL_ECHOLNPAIR(STR_KP, tune_pid.Kp, STR_KI, tune_pid.Ki, STR_KD, tune_pid.Kd);
}
else {
tune_pid.Kp = Ku * pf;
tune_pid.Kd = tune_pid.Kp * Tu * df;
tune_pid.Ki = 2 * tune_pid.Kp / Tu;
SERIAL_ECHOLNPGM("\n" STR_CLASSIC_PID);
SERIAL_ECHOLNPAIR(STR_KP, tune_pid.Kp, STR_KI, tune_pid.Ki, STR_KD, tune_pid.Kd);
}
tune_pid.Kp = Ku * pf;
tune_pid.Ki = tune_pid.Kp * 2.0f / Tu;
tune_pid.Kd = tune_pid.Kp * Tu * df;
/**
tune_pid.Kp = 0.33 * Ku;
tune_pid.Ki = tune_pid.Kp / Tu;
tune_pid.Kd = tune_pid.Kp * Tu / 3;
SERIAL_ECHOLNPGM(" Some overshoot");
SERIAL_ECHOLNPAIR(" Kp: ", tune_pid.Kp, " Ki: ", tune_pid.Ki, " Kd: ", tune_pid.Kd, " No overshoot");
tune_pid.Kp = 0.2 * Ku;
tune_pid.Ki = 2 * tune_pid.Kp / Tu;
tune_pid.Kd = tune_pid.Kp * Tu / 3;
SERIAL_ECHOPAIR(" Kp: ", tune_pid.Kp, " Ki: ", tune_pid.Ki, " Kd: ", tune_pid.Kd);
*/
}
SERIAL_ECHOLNPAIR(STR_KU, Ku, STR_TU, Tu);
if (ischamber || isbed)
SERIAL_ECHOLNPGM(" No overshoot");
else
SERIAL_ECHOLNPGM(STR_CLASSIC_PID);
SERIAL_ECHOLNPAIR(STR_KP, tune_pid.Kp, STR_KI, tune_pid.Ki, STR_KD, tune_pid.Kd);
}
SHV((bias + d) >> 1, (bias + d) >> 1);
cycles++;
minT = target;
}
SHV((bias + d) >> 1);
cycles++;
minT = target;
}
}
@ -649,14 +625,14 @@ volatile bool Temperature::raw_temps_ready = false;
// Report heater states every 2 seconds
if (ELAPSED(ms, next_temp_ms)) {
#if HAS_TEMP_SENSOR
print_heater_states(isbed ? active_extruder : heater_id);
print_heater_states(ischamber ? active_extruder : (isbed ? active_extruder : heater_id));
SERIAL_EOL();
#endif
next_temp_ms = ms + 2000UL;
// Make sure heating is actually working
#if WATCH_PID
if (BOTH(WATCH_BED, WATCH_HOTENDS) || isbed == DISABLED(WATCH_HOTENDS)) {
if (BOTH(WATCH_BED, WATCH_HOTENDS) || isbed == DISABLED(WATCH_HOTENDS) || ischamber == DISABLED(WATCH_HOTENDS)) {
if (!heated) { // If not yet reached target...
if (current_temp > next_watch_temp) { // Over the watch temp?
next_watch_temp = current_temp + watch_temp_increase; // - set the next temp to watch for
@ -686,43 +662,47 @@ volatile bool Temperature::raw_temps_ready = false;
if (cycles > ncycles && cycles > 2) {
SERIAL_ECHOLNPGM(STR_PID_AUTOTUNE_FINISHED);
#if HAS_PID_FOR_BOTH
const char * const estring = GHV(PSTR("bed"), NUL_STR);
#if EITHER(PIDTEMPBED, PIDTEMPCHAMBER)
PGM_P const estring = GHV(PSTR("chamber"), PSTR("bed"), NUL_STR);
say_default_(); serialprintPGM(estring); SERIAL_ECHOLNPAIR("Kp ", tune_pid.Kp);
say_default_(); serialprintPGM(estring); SERIAL_ECHOLNPAIR("Ki ", tune_pid.Ki);
say_default_(); serialprintPGM(estring); SERIAL_ECHOLNPAIR("Kd ", tune_pid.Kd);
#elif ENABLED(PIDTEMP)
#else
say_default_(); SERIAL_ECHOLNPAIR("Kp ", tune_pid.Kp);
say_default_(); SERIAL_ECHOLNPAIR("Ki ", tune_pid.Ki);
say_default_(); SERIAL_ECHOLNPAIR("Kd ", tune_pid.Kd);
#else
say_default_(); SERIAL_ECHOLNPAIR("bedKp ", tune_pid.Kp);
say_default_(); SERIAL_ECHOLNPAIR("bedKi ", tune_pid.Ki);
say_default_(); SERIAL_ECHOLNPAIR("bedKd ", tune_pid.Kd);
#endif
#define _SET_BED_PID() do { \
temp_bed.pid.Kp = tune_pid.Kp; \
temp_bed.pid.Ki = scalePID_i(tune_pid.Ki); \
temp_bed.pid.Kd = scalePID_d(tune_pid.Kd); \
}while(0)
auto _set_hotend_pid = [](const uint8_t e, const PID_t &in_pid) {
#if ENABLED(PIDTEMP)
PID_PARAM(Kp, e) = in_pid.Kp;
PID_PARAM(Ki, e) = scalePID_i(in_pid.Ki);
PID_PARAM(Kd, e) = scalePID_d(in_pid.Kd);
updatePID();
#else
UNUSED(e); UNUSED(in_pid);
#endif
};
#define _SET_EXTRUDER_PID() do { \
PID_PARAM(Kp, heater_id) = tune_pid.Kp; \
PID_PARAM(Ki, heater_id) = scalePID_i(tune_pid.Ki); \
PID_PARAM(Kd, heater_id) = scalePID_d(tune_pid.Kd); \
updatePID(); }while(0)
#if ENABLED(PIDTEMPBED)
auto _set_bed_pid = [](const PID_t &in_pid) {
temp_bed.pid.Kp = in_pid.Kp;
temp_bed.pid.Ki = scalePID_i(in_pid.Ki);
temp_bed.pid.Kd = scalePID_d(in_pid.Kd);
};
#endif
#if ENABLED(PIDTEMPCHAMBER)
auto _set_chamber_pid = [](const PID_t &in_pid) {
temp_chamber.pid.Kp = in_pid.Kp;
temp_chamber.pid.Ki = scalePID_i(in_pid.Ki);
temp_chamber.pid.Kd = scalePID_d(in_pid.Kd);
};
#endif
// Use the result? (As with "M303 U1")
if (set_result) {
#if HAS_PID_FOR_BOTH
if (isbed) _SET_BED_PID(); else _SET_EXTRUDER_PID();
#elif ENABLED(PIDTEMP)
_SET_EXTRUDER_PID();
#else
_SET_BED_PID();
#endif
}
if (set_result)
GHV(_set_chamber_pid(tune_pid), _set_bed_pid(tune_pid), _set_hotend_pid(heater_id, tune_pid));
TERN_(PRINTER_EVENT_LEDS, printerEventLEDs.onPidTuningDone(color));
@ -939,10 +919,11 @@ void Temperature::min_temp_error(const heater_id_t heater_id) {
_temp_error(heater_id, PSTR(STR_T_MINTEMP), GET_TEXT(MSG_ERR_MINTEMP));
}
#if ANY(PID_DEBUG, PID_BED_DEBUG, PID_CHAMBER_DEBUG)
bool Temperature::pid_debug_flag; // = 0
#endif
#if HAS_HOTEND
#if ENABLED(PID_DEBUG)
extern bool pid_debug_flag;
#endif
float Temperature::get_pid_output_hotend(const uint8_t E_NAME) {
const uint8_t ee = HOTEND_INDEX;
@ -1023,23 +1004,18 @@ void Temperature::min_temp_error(const heater_id_t heater_id) {
#if ENABLED(PID_DEBUG)
if (ee == active_extruder && pid_debug_flag) {
SERIAL_ECHO_START();
SERIAL_ECHOPAIR(STR_PID_DEBUG, ee, STR_PID_DEBUG_INPUT, temp_hotend[ee].celsius, STR_PID_DEBUG_OUTPUT, pid_output);
#if DISABLED(PID_OPENLOOP)
{
SERIAL_ECHOPAIR(
STR_PID_DEBUG_PTERM, work_pid[ee].Kp,
STR_PID_DEBUG_ITERM, work_pid[ee].Ki,
STR_PID_DEBUG_DTERM, work_pid[ee].Kd
SERIAL_ECHO_MSG(STR_PID_DEBUG, ee, STR_PID_DEBUG_INPUT, temp_hotend[ee].celsius, STR_PID_DEBUG_OUTPUT, pid_output
#if DISABLED(PID_OPENLOOP)
, STR_PID_DEBUG_PTERM, work_pid[ee].Kp
, STR_PID_DEBUG_ITERM, work_pid[ee].Ki
, STR_PID_DEBUG_DTERM, work_pid[ee].Kd
#if ENABLED(PID_EXTRUSION_SCALING)
, STR_PID_DEBUG_CTERM, work_pid[ee].Kc
#endif
);
}
#endif
SERIAL_EOL();
#endif
);
}
#endif // PID_DEBUG
#endif
#else // No PID enabled
@ -1099,13 +1075,76 @@ void Temperature::min_temp_error(const heater_id_t heater_id) {
#endif // PID_OPENLOOP
#if ENABLED(PID_BED_DEBUG)
if (pid_debug_flag) {
SERIAL_ECHO_MSG(
" PID_BED_DEBUG : Input ", temp_bed.celsius, " Output ", pid_output
#if DISABLED(PID_OPENLOOP)
, STR_PID_DEBUG_PTERM, work_pid.Kp
, STR_PID_DEBUG_ITERM, work_pid.Ki
, STR_PID_DEBUG_DTERM, work_pid.Kd
#endif
);
}
#endif
return pid_output;
}
#endif // PIDTEMPBED
#if ENABLED(PIDTEMPCHAMBER)
float Temperature::get_pid_output_chamber() {
#if DISABLED(PID_OPENLOOP)
static PID_t work_pid{0};
static float temp_iState = 0, temp_dState = 0;
static bool pid_reset = true;
float pid_output = 0;
const float max_power_over_i_gain = float(MAX_CHAMBER_POWER) / temp_chamber.pid.Ki - float(MIN_CHAMBER_POWER),
pid_error = temp_chamber.target - temp_chamber.celsius;
if (!temp_chamber.target || pid_error < -(PID_FUNCTIONAL_RANGE)) {
pid_output = 0;
pid_reset = true;
}
else if (pid_error > PID_FUNCTIONAL_RANGE) {
pid_output = MAX_CHAMBER_POWER;
pid_reset = true;
}
else {
if (pid_reset) {
temp_iState = 0.0;
work_pid.Kd = 0.0;
pid_reset = false;
}
temp_iState = constrain(temp_iState + pid_error, 0, max_power_over_i_gain);
work_pid.Kp = temp_chamber.pid.Kp * pid_error;
work_pid.Ki = temp_chamber.pid.Ki * temp_iState;
work_pid.Kd = work_pid.Kd + PID_K2 * (temp_chamber.pid.Kd * (temp_dState - temp_chamber.celsius) - work_pid.Kd);
temp_dState = temp_chamber.celsius;
pid_output = constrain(work_pid.Kp + work_pid.Ki + work_pid.Kd + float(MIN_CHAMBER_POWER), 0, MAX_CHAMBER_POWER);
}
#else // PID_OPENLOOP
const float pid_output = constrain(temp_chamber.target, 0, MAX_CHAMBER_POWER);
#endif // PID_OPENLOOP
#if ENABLED(PID_CHAMBER_DEBUG)
{
SERIAL_ECHO_MSG(
" PID_BED_DEBUG : Input ", temp_bed.celsius, " Output ", pid_output,
" PID_CHAMBER_DEBUG : Input ", temp_chamber.celsius, " Output ", pid_output
#if DISABLED(PID_OPENLOOP)
STR_PID_DEBUG_PTERM, work_pid.Kp,
STR_PID_DEBUG_ITERM, work_pid.Ki,
STR_PID_DEBUG_DTERM, work_pid.Kd,
, STR_PID_DEBUG_PTERM, work_pid.Kp
, STR_PID_DEBUG_ITERM, work_pid.Ki
, STR_PID_DEBUG_DTERM, work_pid.Kd
#endif
);
}
@ -1114,7 +1153,7 @@ void Temperature::min_temp_error(const heater_id_t heater_id) {
return pid_output;
}
#endif // PIDTEMPBED
#endif // PIDTEMPCHAMBER
/**
* Manage heating activities for extruder hot-ends and a heated bed
@ -1363,42 +1402,47 @@ void Temperature::manage_heater() {
}
#endif
#if ENABLED(PIDTEMPCHAMBER)
// PIDTEMPCHAMBER doens't support a CHAMBER_VENT yet.
temp_chamber.soft_pwm_amount = WITHIN(temp_chamber.celsius, CHAMBER_MINTEMP, CHAMBER_MAXTEMP) ? (int)get_pid_output_chamber() >> 1 : 0;
#else
if (ELAPSED(ms, next_chamber_check_ms)) {
next_chamber_check_ms = ms + CHAMBER_CHECK_INTERVAL;
if (WITHIN(temp_chamber.celsius, CHAMBER_MINTEMP, CHAMBER_MAXTEMP)) {
if (flag_chamber_excess_heat) {
temp_chamber.soft_pwm_amount = 0;
#if ENABLED(CHAMBER_VENT)
if (!flag_chamber_off) MOVE_SERVO(CHAMBER_VENT_SERVO_NR, temp_chamber.celsius <= temp_chamber.target ? 0 : 90);
#endif
if (flag_chamber_excess_heat) {
temp_chamber.soft_pwm_amount = 0;
#if ENABLED(CHAMBER_VENT)
if (!flag_chamber_off) MOVE_SERVO(CHAMBER_VENT_SERVO_NR, temp_chamber.celsius <= temp_chamber.target ? 0 : 90);
#endif
}
else {
#if ENABLED(CHAMBER_LIMIT_SWITCHING)
if (temp_chamber.celsius >= temp_chamber.target + TEMP_CHAMBER_HYSTERESIS)
temp_chamber.soft_pwm_amount = 0;
else if (temp_chamber.celsius <= temp_chamber.target - (TEMP_CHAMBER_HYSTERESIS))
temp_chamber.soft_pwm_amount = (MAX_CHAMBER_POWER) >> 1;
#else
temp_chamber.soft_pwm_amount = temp_chamber.celsius < temp_chamber.target ? (MAX_CHAMBER_POWER) >> 1 : 0;
#endif
#if ENABLED(CHAMBER_VENT)
if (!flag_chamber_off) MOVE_SERVO(CHAMBER_VENT_SERVO_NR, 0);
#endif
}
}
else {
#if ENABLED(CHAMBER_LIMIT_SWITCHING)
if (temp_chamber.celsius >= temp_chamber.target + TEMP_CHAMBER_HYSTERESIS)
temp_chamber.soft_pwm_amount = 0;
else if (temp_chamber.celsius <= temp_chamber.target - (TEMP_CHAMBER_HYSTERESIS))
temp_chamber.soft_pwm_amount = (MAX_CHAMBER_POWER) >> 1;
#else
temp_chamber.soft_pwm_amount = temp_chamber.celsius < temp_chamber.target ? (MAX_CHAMBER_POWER) >> 1 : 0;
#endif
#if ENABLED(CHAMBER_VENT)
if (!flag_chamber_off) MOVE_SERVO(CHAMBER_VENT_SERVO_NR, 0);
#endif
temp_chamber.soft_pwm_amount = 0;
WRITE_HEATER_CHAMBER(LOW);
}
}
else {
temp_chamber.soft_pwm_amount = 0;
WRITE_HEATER_CHAMBER(LOW);
}
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
tr_state_machine[RUNAWAY_IND_CHAMBER].run(temp_chamber.celsius, temp_chamber.target, H_CHAMBER, THERMAL_PROTECTION_CHAMBER_PERIOD, THERMAL_PROTECTION_CHAMBER_HYSTERESIS);
#endif
}
// TODO: Implement true PID pwm
//temp_bed.soft_pwm_amount = WITHIN(temp_chamber.celsius, CHAMBER_MINTEMP, CHAMBER_MAXTEMP) ? (int)get_pid_output_chamber() >> 1 : 0;
}
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
tr_state_machine[RUNAWAY_IND_CHAMBER].run(temp_chamber.celsius, temp_chamber.target, H_CHAMBER, THERMAL_PROTECTION_CHAMBER_PERIOD, THERMAL_PROTECTION_CHAMBER_HYSTERESIS);
#endif
#endif
#endif // HAS_HEATED_CHAMBER

21
Marlin/src/module/temperature.h
View file

@ -210,7 +210,11 @@ struct PIDHeaterInfo : public HeaterInfo {
typedef temp_info_t probe_info_t;
#endif
#if HAS_HEATED_CHAMBER
typedef heater_info_t chamber_info_t;
#if ENABLED(PIDTEMPCHAMBER)
typedef struct PIDHeaterInfo<PID_t> chamber_info_t;
#else
typedef heater_info_t chamber_info_t;
#endif
#elif HAS_TEMP_CHAMBER
typedef temp_info_t chamber_info_t;
#endif
@ -415,7 +419,7 @@ class Temperature {
#if HAS_HEATED_CHAMBER
TERN_(WATCH_CHAMBER, static chamber_watch_t watch_chamber);
static millis_t next_chamber_check_ms;
TERN(PIDTEMPCHAMBER,,static millis_t next_chamber_check_ms);
#ifdef CHAMBER_MINTEMP
static int16_t mintemp_raw_CHAMBER;
#endif
@ -751,6 +755,11 @@ class Temperature {
* Perform auto-tuning for hotend or bed in response to M303
*/
#if HAS_PID_HEATING
#if ANY(PID_DEBUG, PID_BED_DEBUG, PID_CHAMBER_DEBUG)
static bool pid_debug_flag;
#endif
static void PID_autotune(const float &target, const heater_id_t heater_id, const int8_t ncycles, const bool set_result=false);
#if ENABLED(NO_FAN_SLOWING_IN_PID_TUNING)
@ -826,11 +835,9 @@ class Temperature {
static void checkExtruderAutoFans();
static float get_pid_output_hotend(const uint8_t e);
TERN_(PIDTEMPBED, static float get_pid_output_bed());
TERN_(HAS_HEATED_CHAMBER, static float get_pid_output_chamber());
TERN_(HAS_HOTEND, static float get_pid_output_hotend(const uint8_t e));
TERN_(PIDTEMPBED, static float get_pid_output_bed());
TERN_(PIDTEMPCHAMBER, static float get_pid_output_chamber());
static void _temp_error(const heater_id_t e, PGM_P const serial_msg, PGM_P const lcd_msg);
static void min_temp_error(const heater_id_t e);