diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h index f34cd94746..f200d8c3e0 100644 --- a/Marlin/Configuration.h +++ b/Marlin/Configuration.h @@ -94,11 +94,11 @@ // @section machine /** - * Select which serial port on the board will be used for communication with the host. + * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port 0 is always used by the Arduino bootloader regardless of this setting. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * - * :[0, 1, 2, 3, 4, 5, 6, 7] + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT 0 diff --git a/Marlin/src/config/default/Configuration.h b/Marlin/src/config/default/Configuration.h index f34cd94746..f200d8c3e0 100644 --- a/Marlin/src/config/default/Configuration.h +++ b/Marlin/src/config/default/Configuration.h @@ -94,11 +94,11 @@ // @section machine /** - * Select which serial port on the board will be used for communication with the host. + * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port 0 is always used by the Arduino bootloader regardless of this setting. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * - * :[0, 1, 2, 3, 4, 5, 6, 7] + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT 0 diff --git a/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h b/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h index 27c29a0d7a..9c1b7e7ca7 100644 --- a/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h +++ b/Marlin/src/config/examples/AlephObjects/TAZ4/Configuration.h @@ -94,11 +94,11 @@ // @section machine /** - * Select which serial port on the board will be used for communication with the host. + * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port 0 is always used by the Arduino bootloader regardless of this setting. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * - * :[0, 1, 2, 3, 4, 5, 6, 7] + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT 0 diff --git a/Marlin/src/config/examples/AliExpress/CL-260/Configuration.h b/Marlin/src/config/examples/AliExpress/CL-260/Configuration.h index 4b8e2d65c7..b69169d709 100644 --- a/Marlin/src/config/examples/AliExpress/CL-260/Configuration.h +++ b/Marlin/src/config/examples/AliExpress/CL-260/Configuration.h @@ -94,11 +94,11 @@ // @section machine /** - * Select which serial port on the board will be used for communication with the host. + * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port 0 is always used by the Arduino bootloader regardless of this setting. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * - * :[0, 1, 2, 3, 4, 5, 6, 7] + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT 0 diff --git a/Marlin/src/config/examples/Anet/A6/Configuration.h b/Marlin/src/config/examples/Anet/A6/Configuration.h index 2d4530b0a6..c95b03aafa 100644 --- a/Marlin/src/config/examples/Anet/A6/Configuration.h +++ b/Marlin/src/config/examples/Anet/A6/Configuration.h @@ -94,11 +94,11 @@ // @section machine /** - * Select which serial port on the board will be used for communication with the host. + * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port 0 is always used by the Arduino bootloader regardless of this setting. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * - * :[0, 1, 2, 3, 4, 5, 6, 7] + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT 0 diff --git a/Marlin/src/config/examples/Anet/A8/Configuration.h b/Marlin/src/config/examples/Anet/A8/Configuration.h index 5650176a8f..aeabb4d8be 100644 --- a/Marlin/src/config/examples/Anet/A8/Configuration.h +++ b/Marlin/src/config/examples/Anet/A8/Configuration.h @@ -94,11 +94,11 @@ // @section machine /** - * Select which serial port on the board will be used for communication with the host. + * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port 0 is always used by the Arduino bootloader regardless of this setting. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * - * :[0, 1, 2, 3, 4, 5, 6, 7] + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT 0 diff --git a/Marlin/src/config/examples/Azteeg/X5GT/Configuration.h b/Marlin/src/config/examples/Azteeg/X5GT/Configuration.h index 51b88588b7..95a3fb246a 100644 --- a/Marlin/src/config/examples/Azteeg/X5GT/Configuration.h +++ b/Marlin/src/config/examples/Azteeg/X5GT/Configuration.h @@ -94,13 +94,13 @@ // @section machine /** - * Select which serial port on the board will be used for communication with the host. + * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port 0 is always used by the Arduino bootloader regardless of this setting. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * - * :[0, 1, 2, 3, 4, 5, 6, 7] + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ -#define SERIAL_PORT -1 +#define SERIAL_PORT 0 /** * This setting determines the communication speed of the printer. diff --git a/Marlin/src/config/examples/BQ/Hephestos/Configuration.h b/Marlin/src/config/examples/BQ/Hephestos/Configuration.h index d9db41c64a..6df0f92c6a 100644 --- a/Marlin/src/config/examples/BQ/Hephestos/Configuration.h +++ b/Marlin/src/config/examples/BQ/Hephestos/Configuration.h @@ -94,11 +94,11 @@ // @section machine /** - * Select which serial port on the board will be used for communication with the host. + * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port 0 is always used by the Arduino bootloader regardless of this setting. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * - * :[0, 1, 2, 3, 4, 5, 6, 7] + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT 0 diff --git a/Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h b/Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h index 1166a19995..4ea135dbb9 100644 --- a/Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h +++ b/Marlin/src/config/examples/BQ/Hephestos_2/Configuration.h @@ -93,11 +93,11 @@ // @section machine /** - * Select which serial port on the board will be used for communication with the host. + * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port 0 is always used by the Arduino bootloader regardless of this setting. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * - * :[0, 1, 2, 3, 4, 5, 6, 7] + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT 0 diff --git a/Marlin/src/config/examples/BQ/WITBOX/Configuration.h b/Marlin/src/config/examples/BQ/WITBOX/Configuration.h index 2c285d686f..074ade9b27 100644 --- a/Marlin/src/config/examples/BQ/WITBOX/Configuration.h +++ b/Marlin/src/config/examples/BQ/WITBOX/Configuration.h @@ -94,11 +94,11 @@ // @section machine /** - * Select which serial port on the board will be used for communication with the host. + * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port 0 is always used by the Arduino bootloader regardless of this setting. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * - * :[0, 1, 2, 3, 4, 5, 6, 7] + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT 0 diff --git a/Marlin/src/config/examples/Cartesio/Configuration.h b/Marlin/src/config/examples/Cartesio/Configuration.h index 96359bec68..6c989bb732 100644 --- a/Marlin/src/config/examples/Cartesio/Configuration.h +++ b/Marlin/src/config/examples/Cartesio/Configuration.h @@ -94,11 +94,11 @@ // @section machine /** - * Select which serial port on the board will be used for communication with the host. + * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port 0 is always used by the Arduino bootloader regardless of this setting. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * - * :[0, 1, 2, 3, 4, 5, 6, 7] + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT 0 diff --git a/Marlin/src/config/examples/Creality/CR-10/Configuration.h b/Marlin/src/config/examples/Creality/CR-10/Configuration.h index 5f2a86c997..51fdc70e5b 100755 --- a/Marlin/src/config/examples/Creality/CR-10/Configuration.h +++ b/Marlin/src/config/examples/Creality/CR-10/Configuration.h @@ -94,11 +94,11 @@ // @section machine /** - * Select which serial port on the board will be used for communication with the host. + * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port 0 is always used by the Arduino bootloader regardless of this setting. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * - * :[0, 1, 2, 3, 4, 5, 6, 7] + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT 0 diff --git a/Marlin/src/config/examples/Felix/Configuration.h b/Marlin/src/config/examples/Felix/Configuration.h index a3eca68f13..9f8dfbed4d 100644 --- a/Marlin/src/config/examples/Felix/Configuration.h +++ b/Marlin/src/config/examples/Felix/Configuration.h @@ -94,11 +94,11 @@ // @section machine /** - * Select which serial port on the board will be used for communication with the host. + * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port 0 is always used by the Arduino bootloader regardless of this setting. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * - * :[0, 1, 2, 3, 4, 5, 6, 7] + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT 0 diff --git a/Marlin/src/config/examples/Felix/DUAL/Configuration.h b/Marlin/src/config/examples/Felix/DUAL/Configuration.h index 64ac9de30d..aedacb971a 100644 --- a/Marlin/src/config/examples/Felix/DUAL/Configuration.h +++ b/Marlin/src/config/examples/Felix/DUAL/Configuration.h @@ -94,11 +94,11 @@ // @section machine /** - * Select which serial port on the board will be used for communication with the host. + * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port 0 is always used by the Arduino bootloader regardless of this setting. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * - * :[0, 1, 2, 3, 4, 5, 6, 7] + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT 0 diff --git a/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h b/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h index 519af40fda..deed4a40a1 100644 --- a/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h +++ b/Marlin/src/config/examples/FolgerTech/i3-2020/Configuration.h @@ -94,11 +94,11 @@ // @section machine /** - * Select which serial port on the board will be used for communication with the host. + * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port 0 is always used by the Arduino bootloader regardless of this setting. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * - * :[0, 1, 2, 3, 4, 5, 6, 7] + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT 0 diff --git a/Marlin/src/config/examples/Geeetech/GT2560/Configuration.h b/Marlin/src/config/examples/Geeetech/GT2560/Configuration.h index 10ac9cc6e1..2b5d0282e2 100644 --- a/Marlin/src/config/examples/Geeetech/GT2560/Configuration.h +++ b/Marlin/src/config/examples/Geeetech/GT2560/Configuration.h @@ -94,11 +94,11 @@ // @section machine /** - * Select which serial port on the board will be used for communication with the host. + * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port 0 is always used by the Arduino bootloader regardless of this setting. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * - * :[0, 1, 2, 3, 4, 5, 6, 7] + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT 0 diff --git a/Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h b/Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h index 14c92f59e1..432331cd18 100644 --- a/Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h +++ b/Marlin/src/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h @@ -94,11 +94,11 @@ // @section machine /** - * Select which serial port on the board will be used for communication with the host. + * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port 0 is always used by the Arduino bootloader regardless of this setting. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * - * :[0, 1, 2, 3, 4, 5, 6, 7] + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT 0 diff --git a/Marlin/src/config/examples/Infitary/i3-M508/Configuration.h b/Marlin/src/config/examples/Infitary/i3-M508/Configuration.h index b88c6e0927..b10fb07305 100644 --- a/Marlin/src/config/examples/Infitary/i3-M508/Configuration.h +++ b/Marlin/src/config/examples/Infitary/i3-M508/Configuration.h @@ -94,11 +94,11 @@ // @section machine /** - * Select which serial port on the board will be used for communication with the host. + * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port 0 is always used by the Arduino bootloader regardless of this setting. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * - * :[0, 1, 2, 3, 4, 5, 6, 7] + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT 0 diff --git a/Marlin/src/config/examples/Malyan/M150/Configuration.h b/Marlin/src/config/examples/Malyan/M150/Configuration.h index 3b4bacc41e..3c37be67ee 100644 --- a/Marlin/src/config/examples/Malyan/M150/Configuration.h +++ b/Marlin/src/config/examples/Malyan/M150/Configuration.h @@ -99,11 +99,11 @@ // @section machine /** - * Select which serial port on the board will be used for communication with the host. + * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port 0 is always used by the Arduino bootloader regardless of this setting. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * - * :[0, 1, 2, 3, 4, 5, 6, 7] + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT 0 diff --git a/Marlin/src/config/examples/Micromake/C1/basic/Configuration.h b/Marlin/src/config/examples/Micromake/C1/basic/Configuration.h index c72afec070..f60f077839 100644 --- a/Marlin/src/config/examples/Micromake/C1/basic/Configuration.h +++ b/Marlin/src/config/examples/Micromake/C1/basic/Configuration.h @@ -94,11 +94,11 @@ // @section machine /** - * Select which serial port on the board will be used for communication with the host. + * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port 0 is always used by the Arduino bootloader regardless of this setting. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * - * :[0, 1, 2, 3, 4, 5, 6, 7] + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT 0 diff --git a/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h b/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h index 8b9581fa5b..59fbd52a93 100644 --- a/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h +++ b/Marlin/src/config/examples/Micromake/C1/enhanced/Configuration.h @@ -94,11 +94,11 @@ // @section machine /** - * Select which serial port on the board will be used for communication with the host. + * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port 0 is always used by the Arduino bootloader regardless of this setting. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * - * :[0, 1, 2, 3, 4, 5, 6, 7] + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT 0 diff --git a/Marlin/src/config/examples/Mks/Sbase/Configuration.h b/Marlin/src/config/examples/Mks/Sbase/Configuration.h index 8e5a8835a7..d2f05ed5a9 100644 --- a/Marlin/src/config/examples/Mks/Sbase/Configuration.h +++ b/Marlin/src/config/examples/Mks/Sbase/Configuration.h @@ -38,7 +38,6 @@ #ifndef CONFIGURATION_H #define CONFIGURATION_H #define CONFIGURATION_H_VERSION 020000 -#define USE_AUTOMATIC_VERSIONING //=========================================================================== //============================= Getting Started ============================= @@ -96,11 +95,11 @@ // @section machine /** - * Select which serial port on the board will be used for communication with the host. + * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port 0 is always used by the Arduino bootloader regardless of this setting. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * - * :[0, 1, 2, 3, 4, 5, 6, 7] + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT 0 diff --git a/Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h b/Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h index 7206d9c070..f7c42f7434 100644 --- a/Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h +++ b/Marlin/src/config/examples/RepRapWorld/Megatronics/Configuration.h @@ -94,11 +94,11 @@ // @section machine /** - * Select which serial port on the board will be used for communication with the host. + * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port 0 is always used by the Arduino bootloader regardless of this setting. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * - * :[0, 1, 2, 3, 4, 5, 6, 7] + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT 0 diff --git a/Marlin/src/config/examples/RigidBot/Configuration.h b/Marlin/src/config/examples/RigidBot/Configuration.h index 783a3d9ba2..fd66add479 100644 --- a/Marlin/src/config/examples/RigidBot/Configuration.h +++ b/Marlin/src/config/examples/RigidBot/Configuration.h @@ -94,11 +94,11 @@ // @section machine /** - * Select which serial port on the board will be used for communication with the host. + * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port 0 is always used by the Arduino bootloader regardless of this setting. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * - * :[0, 1, 2, 3, 4, 5, 6, 7] + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT 0 diff --git a/Marlin/src/config/examples/SCARA/Configuration.h b/Marlin/src/config/examples/SCARA/Configuration.h index 5d1621b2c8..ed6867d6de 100644 --- a/Marlin/src/config/examples/SCARA/Configuration.h +++ b/Marlin/src/config/examples/SCARA/Configuration.h @@ -124,11 +124,11 @@ // @section machine /** - * Select which serial port on the board will be used for communication with the host. + * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port 0 is always used by the Arduino bootloader regardless of this setting. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * - * :[0, 1, 2, 3, 4, 5, 6, 7] + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT 0 diff --git a/Marlin/src/config/examples/STM32F103RET6/Configuration.h b/Marlin/src/config/examples/STM32F103RET6/Configuration.h new file mode 100644 index 0000000000..90f0c67bc9 --- /dev/null +++ b/Marlin/src/config/examples/STM32F103RET6/Configuration.h @@ -0,0 +1,1731 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ + +/** + * Configuration.h + * + * Basic settings such as: + * + * - Type of electronics + * - Type of temperature sensor + * - Printer geometry + * - Endstop configuration + * - LCD controller + * - Extra features + * + * Advanced settings can be found in Configuration_adv.h + * + */ +#ifndef CONFIGURATION_H +#define CONFIGURATION_H +#define CONFIGURATION_H_VERSION 020000 + +//=========================================================================== +//============================= Getting Started ============================= +//=========================================================================== + +/** + * Here are some standard links for getting your machine calibrated: + * + * http://reprap.org/wiki/Calibration + * http://youtu.be/wAL9d7FgInk + * http://calculator.josefprusa.cz + * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide + * http://www.thingiverse.com/thing:5573 + * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap + * http://www.thingiverse.com/thing:298812 + */ + +//=========================================================================== +//============================= DELTA Printer =============================== +//=========================================================================== +// For a Delta printer start with one of the configuration files in the +// config/examples/delta directory and customize for your machine. +// + +//=========================================================================== +//============================= SCARA Printer =============================== +//=========================================================================== +// For a SCARA printer start with the configuration files in +// config/examples/SCARA and customize for your machine. +// + +// @section info + +// User-specified version info of this build to display in [Pronterface, etc] terminal window during +// startup. Implementation of an idea by Prof Braino to inform user that any changes made to this +// build by the user have been successfully uploaded into firmware. +#define STRING_CONFIG_H_AUTHOR "Victor Perez" // Who made the changes. +#define SHOW_BOOTSCREEN +#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION "STM32F103RET6 board" // will be shown during bootup in line 1 +#define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2 + +// +// *** VENDORS PLEASE READ ***************************************************** +// +// Marlin now allow you to have a vendor boot image to be displayed on machine +// start. When SHOW_CUSTOM_BOOTSCREEN is defined Marlin will first show your +// custom boot image and then the default Marlin boot image is shown. +// +// We suggest for you to take advantage of this new feature and keep the Marlin +// boot image unmodified. For an example have a look at the bq Hephestos 2 +// example configuration folder. +// +//#define SHOW_CUSTOM_BOOTSCREEN +// @section machine + +/** + * Select the serial port on the board to use for communication with the host. + * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. + * + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] + */ +#define SERIAL_PORT 0 + +/** + * This setting determines the communication speed of the printer. + * + * 250000 works in most cases, but you might try a lower speed if + * you commonly experience drop-outs during host printing. + * You may try up to 1000000 to speed up SD file transfer. + * + * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000] + */ +#define BAUDRATE 250000 + +// Enable the Bluetooth serial interface on AT90USB devices +//#define BLUETOOTH + +// The following define selects which electronics board you have. +// Please choose the name from boards.h that matches your setup +#ifndef MOTHERBOARD + #define MOTHERBOARD BOARD_STM32F1R +#endif + +// Optional custom name for your RepStrap or other custom machine +// Displayed in the LCD "Ready" message +#define CUSTOM_MACHINE_NAME "CTC i3 Pro B" + +// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) +// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" + +// @section extruder + +// This defines the number of extruders +// :[1, 2, 3, 4, 5] +#define EXTRUDERS 1 + +// For Cyclops or any "multi-extruder" that shares a single nozzle. +//#define SINGLENOZZLE + +/** + * Průša MK2 Single Nozzle Multi-Material Multiplexer, and variants. + * + * This device allows one stepper driver on a control board to drive + * two to eight stepper motors, one at a time, in a manner suitable + * for extruders. + * + * This option only allows the multiplexer to switch on tool-change. + * Additional options to configure custom E moves are pending. + */ +//#define MK2_MULTIPLEXER +#if ENABLED(MK2_MULTIPLEXER) + // Override the default DIO selector pins here, if needed. + // Some pins files may provide defaults for these pins. + //#define E_MUX0_PIN 40 // Always Required + //#define E_MUX1_PIN 42 // Needed for 3 to 8 steppers + //#define E_MUX2_PIN 44 // Needed for 5 to 8 steppers +#endif + +// A dual extruder that uses a single stepper motor +//#define SWITCHING_EXTRUDER +#if ENABLED(SWITCHING_EXTRUDER) + #define SWITCHING_EXTRUDER_SERVO_NR 0 + #define SWITCHING_EXTRUDER_SERVO_ANGLES { 0, 90 } // Angles for E0, E1[, E2, E3] + #if EXTRUDERS > 3 + #define SWITCHING_EXTRUDER_E23_SERVO_NR 1 + #endif +#endif + +// A dual-nozzle that uses a servomotor to raise/lower one of the nozzles +//#define SWITCHING_NOZZLE +#if ENABLED(SWITCHING_NOZZLE) + #define SWITCHING_NOZZLE_SERVO_NR 0 + #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 + //#define HOTEND_OFFSET_Z { 0.0, 0.0 } +#endif + +/** + * Two separate X-carriages with extruders that connect to a moving part + * via a magnetic docking mechanism. Requires SOL1_PIN and SOL2_PIN. + */ +//#define PARKING_EXTRUDER +#if ENABLED(PARKING_EXTRUDER) + #define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage + #define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil + #define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // Delay (ms) for magnetic field. No delay if 0 or not defined. + #define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders + #define PARKING_EXTRUDER_GRAB_DISTANCE 1 // mm to move beyond the parking point to grab the extruder + #define PARKING_EXTRUDER_SECURITY_RAISE 5 // Z-raise before parking + #define HOTEND_OFFSET_Z { 0.0, 1.3 } // Z-offsets of the two hotends. The first must be 0. +#endif + +/** + * "Mixing Extruder" + * - Adds a new code, M165, to set the current mix factors. + * - Extends the stepping routines to move multiple steppers in proportion to the mix. + * - Optional support for Repetier Firmware M163, M164, and virtual extruder. + * - This implementation supports only a single extruder. + * - Enable DIRECT_MIXING_IN_G1 for Pia Taubert's reference implementation + */ +//#define MIXING_EXTRUDER +#if ENABLED(MIXING_EXTRUDER) + #define MIXING_STEPPERS 2 // Number of steppers in your mixing extruder + #define MIXING_VIRTUAL_TOOLS 16 // Use the Virtual Tool method with M163 and M164 + //#define DIRECT_MIXING_IN_G1 // Allow ABCDHI mix factors in G1 movement commands +#endif + +// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). +// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). +// For the other hotends it is their distance from the extruder 0 hotend. +//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis +//#define HOTEND_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis + +// @section machine + +/** + * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN + * + * 0 = No Power Switch + * 1 = ATX + * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC) + * + * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' } + */ +#define POWER_SUPPLY 0 + +#if POWER_SUPPLY > 0 + // Enable this option to leave the PSU off at startup. + // Power to steppers and heaters will need to be turned on with M80. + //#define PS_DEFAULT_OFF +#endif + +// @section temperature + +//=========================================================================== +//============================= Thermal Settings ============================ +//=========================================================================== + +/** + * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table + * + * Temperature sensors available: + * + * -3 : thermocouple with MAX31855 (only for sensor 0) + * -2 : thermocouple with MAX6675 (only for sensor 0) + * -1 : thermocouple with AD595 + * 0 : not used + * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 3 : Mendel-parts thermistor (4.7k pullup) + * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! + * 5 : 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup) + * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) + * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) + * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) + * 8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) + * 9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup) + * 10 : 100k RS thermistor 198-961 (4.7k pullup) + * 11 : 100k beta 3950 1% thermistor (4.7k pullup) + * 12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed) + * 13 : 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE" + * 20 : the PT100 circuit found in the Ultimainboard V2.x + * 60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950 + * 66 : 4.7M High Temperature thermistor from Dyze Design + * 70 : the 100K thermistor found in the bq Hephestos 2 + * 75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor + * + * 1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k. + * (but gives greater accuracy and more stable PID) + * 51 : 100k thermistor - EPCOS (1k pullup) + * 52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup) + * 55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup) + * + * 1047 : Pt1000 with 4k7 pullup + * 1010 : Pt1000 with 1k pullup (non standard) + * 147 : Pt100 with 4k7 pullup + * 110 : Pt100 with 1k pullup (non standard) + * + * Use these for Testing or Development purposes. NEVER for production machine. + * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. + * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. + * + * :{ '0': "Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '66':"Dyze Design 4.7M High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595",'998':"Dummy 1", '999':"Dummy 2" } + */ +#warning temp_sensor set to 998/999 (fake) +#define TEMP_SENSOR_0 999 +#define TEMP_SENSOR_1 0 +#define TEMP_SENSOR_2 0 +#define TEMP_SENSOR_3 0 +#define TEMP_SENSOR_4 0 +#define TEMP_SENSOR_BED 998 + +// Dummy thermistor constant temperature readings, for use with 998 and 999 +#define DUMMY_THERMISTOR_998_VALUE 60 +#define DUMMY_THERMISTOR_999_VALUE 205 + +// Use temp sensor 1 as a redundant sensor with sensor 0. If the readings +// from the two sensors differ too much the print will be aborted. +//#define TEMP_SENSOR_1_AS_REDUNDANT +#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 + +// Extruder temperature must be close to target for this long before M109 returns success +#define TEMP_RESIDENCY_TIME 10 // (seconds) +#define TEMP_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one +#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early. + +// Bed temperature must be close to target for this long before M190 returns success +#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) +#define TEMP_BED_HYSTERESIS 3 // (degC) range of +/- temperatures considered "close" to the target one +#define TEMP_BED_WINDOW 1 // (degC) Window around target to start the residency timer x degC early. + +// The minimal temperature defines the temperature below which the heater will not be enabled It is used +// to check that the wiring to the thermistor is not broken. +// Otherwise this would lead to the heater being powered on all the time. +#define HEATER_0_MINTEMP 5 +#define HEATER_1_MINTEMP 5 +#define HEATER_2_MINTEMP 5 +#define HEATER_3_MINTEMP 5 +#define HEATER_4_MINTEMP 5 +#define BED_MINTEMP 5 + +// When temperature exceeds max temp, your heater will be switched off. +// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! +// You should use MINTEMP for thermistor short/failure protection. +#define HEATER_0_MAXTEMP 275 +#define HEATER_1_MAXTEMP 275 +#define HEATER_2_MAXTEMP 275 +#define HEATER_3_MAXTEMP 275 +#define HEATER_4_MAXTEMP 275 +#define BED_MAXTEMP 150 + +//=========================================================================== +//============================= PID Settings ================================ +//=========================================================================== +// PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning + +// Comment the following line to disable PID and enable bang-bang. +#define PIDTEMP +#define BANG_MAX 180 // limits current to nozzle while in bang-bang mode; 255=full current +#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current +#if ENABLED(PIDTEMP) + #define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result. + //#define PID_DEBUG // Sends debug data to the serial port. + //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX + //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay + //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders) + // Set/get with gcode: M301 E[extruder number, 0-2] + #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature + // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. + #define K1 0.95 //smoothing factor within the PID + + // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it + + // Ultimaker + #define DEFAULT_Kp 22.2 + #define DEFAULT_Ki 1.08 + #define DEFAULT_Kd 114 + + // MakerGear + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 + + // Mendel Parts V9 on 12V + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 + +#endif // PIDTEMP + +//=========================================================================== +//============================= PID > Bed Temperature Control =============== +//=========================================================================== +// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis +// +// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder. +// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz, +// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating. +// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater. +// If your configuration is significantly different than this and you don't understand the issues involved, you probably +// shouldn't use bed PID until someone else verifies your hardware works. +// If this is enabled, find your own PID constants below. +//#define PIDTEMPBED + +//#define BED_LIMIT_SWITCHING + +// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option. +// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis) +// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did, +// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED) +#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current + +#if ENABLED(PIDTEMPBED) + + //#define PID_BED_DEBUG // Sends debug data to the serial port. + + //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) + //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) + #define DEFAULT_bedKp 10.00 + #define DEFAULT_bedKi .023 + #define DEFAULT_bedKd 305.4 + + //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) + //from pidautotune + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 + + // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. +#endif // PIDTEMPBED + +// @section extruder + +// This option prevents extrusion if the temperature is below EXTRUDE_MINTEMP. +// It also enables the M302 command to set the minimum extrusion temperature +// or to allow moving the extruder regardless of the hotend temperature. +// *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! *** +#define PREVENT_COLD_EXTRUSION +#define EXTRUDE_MINTEMP 170 + +// This option prevents a single extrusion longer than EXTRUDE_MAXLENGTH. +// Note that for Bowden Extruders a too-small value here may prevent loading. +#define PREVENT_LENGTHY_EXTRUDE +#define EXTRUDE_MAXLENGTH 200 + +//=========================================================================== +//======================== Thermal Runaway Protection ======================= +//=========================================================================== + +/** + * Thermal Protection protects your printer from damage and fire if a + * thermistor falls out or temperature sensors fail in any way. + * + * The issue: If a thermistor falls out or a temperature sensor fails, + * Marlin can no longer sense the actual temperature. Since a disconnected + * thermistor reads as a low temperature, the firmware will keep the heater on. + * + * If you get "Thermal Runaway" or "Heating failed" errors the + * details can be tuned in Configuration_adv.h + */ + +#warning "disabled temperature protection" +//#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders +//#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed + +//=========================================================================== +//============================= Mechanical Settings ========================= +//=========================================================================== + +// @section machine + +// Uncomment one of these options to enable CoreXY, CoreXZ, or CoreYZ kinematics +// either in the usual order or reversed +//#define COREXY +//#define COREXZ +//#define COREYZ +//#define COREYX +//#define COREZX +//#define COREZY + +//=========================================================================== +//============================== Endstop Settings =========================== +//=========================================================================== + +// @section homing + +// Specify here all the endstop connectors that are connected to any endstop or probe. +// Almost all printers will be using one per axis. Probes will use one or more of the +// extra connectors. Leave undefined any used for non-endstop and non-probe purposes. +#define USE_XMIN_PLUG +#define USE_YMIN_PLUG +#define USE_ZMIN_PLUG +//#define USE_XMAX_PLUG +//#define USE_YMAX_PLUG +//#define USE_ZMAX_PLUG + +// coarse Endstop Settings +#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors + +#if DISABLED(ENDSTOPPULLUPS) + // fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined + //#define ENDSTOPPULLUP_XMAX + //#define ENDSTOPPULLUP_YMAX + //#define ENDSTOPPULLUP_ZMAX + //#define ENDSTOPPULLUP_XMIN + //#define ENDSTOPPULLUP_YMIN + //#define ENDSTOPPULLUP_ZMIN + //#define ENDSTOPPULLUP_ZMIN_PROBE +#endif + +// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup). +#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop. +#define Y_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop. +#define Z_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop. +#define X_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop. +#define Y_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop. +#define Z_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop. +#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe. + +// Enable this feature if all enabled endstop pins are interrupt-capable. +// This will remove the need to poll the interrupt pins, saving many CPU cycles. +//#define ENDSTOP_INTERRUPTS_FEATURE + +//============================================================================= +//============================== Movement Settings ============================ +//============================================================================= +// @section motion + +/** + * Default Settings + * + * These settings can be reset by M502 + * + * Note that if EEPROM is enabled, saved values will override these. + */ + +/** + * With this option each E stepper can have its own factors for the + * following movement settings. If fewer factors are given than the + * total number of extruders, the last value applies to the rest. + */ +//#define DISTINCT_E_FACTORS + +/** + * Default Axis Steps Per Unit (steps/mm) + * Override with M92 + * X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]] + */ +#define DEFAULT_AXIS_STEPS_PER_UNIT { 78.74, 78.74, 2560, 105.0 } + +/** + * Default Max Feed Rate (mm/s) + * Override with M203 + * X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]] + */ +#define DEFAULT_MAX_FEEDRATE { 400, 400, 2, 45 } + +/** + * Default Max Acceleration (change/s) change = mm/s + * (Maximum start speed for accelerated moves) + * Override with M201 + * X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]] + */ +#define DEFAULT_MAX_ACCELERATION { 1400, 1400, 100, 80000 } + +/** + * Default Acceleration (change/s) change = mm/s + * Override with M204 + * + * M204 P Acceleration + * M204 R Retract Acceleration + * M204 T Travel Acceleration + */ +#define DEFAULT_ACCELERATION 1400 // X, Y, Z and E acceleration for printing moves +#define DEFAULT_RETRACT_ACCELERATION 5000 // E acceleration for retracts +#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves + +/** + * Default Jerk (mm/s) + * Override with M205 X Y Z E + * + * "Jerk" specifies the minimum speed change that requires acceleration. + * When changing speed and direction, if the difference is less than the + * value set here, it may happen instantaneously. + */ +#define DEFAULT_XJERK 13.0 +#define DEFAULT_YJERK 13.0 +#define DEFAULT_ZJERK 0.3 +#define DEFAULT_EJERK 5.0 + + +//=========================================================================== +//============================= Z Probe Options ============================= +//=========================================================================== +// @section probes + +// +// See http://marlinfw.org/configuration/probes.html +// + +/** + * Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + * + * Enable this option for a probe connected to the Z Min endstop pin. + */ +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +/** + * Z_MIN_PROBE_ENDSTOP + * + * Enable this option for a probe connected to any pin except Z-Min. + * (By default Marlin assumes the Z-Max endstop pin.) + * To use a custom Z Probe pin, set Z_MIN_PROBE_PIN below. + * + * - The simplest option is to use a free endstop connector. + * - Use 5V for powered (usually inductive) sensors. + * + * - RAMPS 1.3/1.4 boards may use the 5V, GND, and Aux4->D32 pin: + * - For simple switches connect... + * - normally-closed switches to GND and D32. + * - normally-open switches to 5V and D32. + * + * WARNING: Setting the wrong pin may have unexpected and potentially + * disastrous consequences. Use with caution and do your homework. + * + */ +//#define Z_MIN_PROBE_ENDSTOP + +/** + * Probe Type + * + * Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc. + * Activate one of these to use Auto Bed Leveling below. + */ + +/** + * The "Manual Probe" provides a means to do "Auto" Bed Leveling without a probe. + * Use G29 repeatedly, adjusting the Z height at each point with movement commands + * or (with LCD_BED_LEVELING) the LCD controller. + */ +//#define PROBE_MANUALLY + +/** + * A Fix-Mounted Probe either doesn't deploy or needs manual deployment. + * (e.g., an inductive probe or a nozzle-based probe-switch.) + */ +//#define FIX_MOUNTED_PROBE + +/** + * Z Servo Probe, such as an endstop switch on a rotating arm. + */ +//#define Z_ENDSTOP_SERVO_NR 0 // Defaults to SERVO 0 connector. +//#define Z_SERVO_ANGLES {70,0} // Z Servo Deploy and Stow angles + +/** + * The BLTouch probe uses a Hall effect sensor and emulates a servo. + */ +//#define BLTOUCH +#if ENABLED(BLTOUCH) + //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if needed +#endif + +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + +// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) +//#define SOLENOID_PROBE + +// A sled-mounted probe like those designed by Charles Bell. +//#define Z_PROBE_SLED +//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. + +// +// For Z_PROBE_ALLEN_KEY see the Delta example configurations. +// + +/** + * Z Probe to nozzle (X,Y) offset, relative to (0, 0). + * X and Y offsets must be integers. + * + * In the following example the X and Y offsets are both positive: + * #define X_PROBE_OFFSET_FROM_EXTRUDER 10 + * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 + * + * +-- BACK ---+ + * | | + * L | (+) P | R <-- probe (20,20) + * E | | I + * F | (-) N (+) | G <-- nozzle (10,10) + * T | | H + * | (-) | T + * | | + * O-- FRONT --+ + * (0,0) + */ +#define X_PROBE_OFFSET_FROM_EXTRUDER -25 // X offset: -left +right [of the nozzle] +#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // Y offset: -front +behind [the nozzle] +#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // Z offset: -below +above [the nozzle] + +// X and Y axis travel speed (mm/m) between probes +#define XY_PROBE_SPEED 8000 + +// Speed for the first approach when double-probing (with PROBE_DOUBLE_TOUCH) +#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z + +// Speed for the "accurate" probe of each point +#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) + +// Use double touch for probing +//#define PROBE_DOUBLE_TOUCH + +/** + * Z probes require clearance when deploying, stowing, and moving between + * probe points to avoid hitting the bed and other hardware. + * Servo-mounted probes require extra space for the arm to rotate. + * Inductive probes need space to keep from triggering early. + * + * Use these settings to specify the distance (mm) to raise the probe (or + * lower the bed). The values set here apply over and above any (negative) + * probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD. + * Only integer values >= 1 are valid here. + * + * Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle. + * But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle. + */ +#define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow +#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points + +// For M851 give a range for adjusting the Z probe offset +#define Z_PROBE_OFFSET_RANGE_MIN -20 +#define Z_PROBE_OFFSET_RANGE_MAX 20 + +// Enable the M48 repeatability test to test probe accuracy +//#define Z_MIN_PROBE_REPEATABILITY_TEST + +// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 +// :{ 0:'Low', 1:'High' } +#define X_ENABLE_ON 0 +#define Y_ENABLE_ON 0 +#define Z_ENABLE_ON 0 +#define E_ENABLE_ON 0 // For all extruders + +// Disables axis stepper immediately when it's not being used. +// WARNING: When motors turn off there is a chance of losing position accuracy! +#define DISABLE_X false +#define DISABLE_Y false +#define DISABLE_Z false +// Warn on display about possibly reduced accuracy +//#define DISABLE_REDUCED_ACCURACY_WARNING + +// @section extruder + +#define DISABLE_E false // For all extruders +#define DISABLE_INACTIVE_EXTRUDER true // Keep only the active extruder enabled. + +// @section machine + +// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way. +#define INVERT_X_DIR false +#define INVERT_Y_DIR true +#define INVERT_Z_DIR false + +// Enable this option for Toshiba stepper drivers +//#define CONFIG_STEPPERS_TOSHIBA + +// @section extruder + +// For direct drive extruder v9 set to true, for geared extruder set to false. +#define INVERT_E0_DIR true +#define INVERT_E1_DIR false +#define INVERT_E2_DIR false +#define INVERT_E3_DIR false +#define INVERT_E4_DIR false + +// @section homing + +//#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed + +//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ... + // Be sure you have this distance over your Z_MAX_POS in case. + +// Direction of endstops when homing; 1=MAX, -1=MIN +// :[-1,1] +#define X_HOME_DIR -1 +#define Y_HOME_DIR -1 +#define Z_HOME_DIR -1 + +// @section machine + +// The size of the print bed +#define X_BED_SIZE 200 +#define Y_BED_SIZE 200 + +// Travel limits (mm) after homing, corresponding to endstop positions. +#define X_MIN_POS 0 +#define Y_MIN_POS 0 +#define Z_MIN_POS 0 +#define X_MAX_POS X_BED_SIZE +#define Y_MAX_POS Y_BED_SIZE +#define Z_MAX_POS 180 + +/** + * Software Endstops + * + * - Prevent moves outside the set machine bounds. + * - Individual axes can be disabled, if desired. + * - X and Y only apply to Cartesian robots. + * - Use 'M211' to set software endstops on/off or report current state + */ + +// Min software endstops constrain movement within minimum coordinate bounds +#define MIN_SOFTWARE_ENDSTOPS +#if ENABLED(MIN_SOFTWARE_ENDSTOPS) + #define MIN_SOFTWARE_ENDSTOP_X + #define MIN_SOFTWARE_ENDSTOP_Y + #define MIN_SOFTWARE_ENDSTOP_Z +#endif + +// Max software endstops constrain movement within maximum coordinate bounds +#define MAX_SOFTWARE_ENDSTOPS +#if ENABLED(MAX_SOFTWARE_ENDSTOPS) + #define MAX_SOFTWARE_ENDSTOP_X + #define MAX_SOFTWARE_ENDSTOP_Y + #define MAX_SOFTWARE_ENDSTOP_Z +#endif + +/** + * Filament Runout Sensor + * A mechanical or opto endstop is used to check for the presence of filament. + * + * RAMPS-based boards use SERVO3_PIN. + * For other boards you may need to define FIL_RUNOUT_PIN. + * By default the firmware assumes HIGH = has filament, LOW = ran out + */ +//#define FILAMENT_RUNOUT_SENSOR +#if ENABLED(FILAMENT_RUNOUT_SENSOR) + #define FIL_RUNOUT_INVERTING false // set to true to invert the logic of the sensor. + #define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined. + #define FILAMENT_RUNOUT_SCRIPT "M600" +#endif + +//=========================================================================== +//=============================== Bed Leveling ============================== +//=========================================================================== +// @section bedlevel + +/** + * Choose one of the options below to enable G29 Bed Leveling. The parameters + * and behavior of G29 will change depending on your selection. + * + * If using a Probe for Z Homing, enable Z_SAFE_HOMING also! + * + * - AUTO_BED_LEVELING_3POINT + * Probe 3 arbitrary points on the bed (that aren't collinear) + * You specify the XY coordinates of all 3 points. + * The result is a single tilted plane. Best for a flat bed. + * + * - AUTO_BED_LEVELING_LINEAR + * Probe several points in a grid. + * You specify the rectangle and the density of sample points. + * The result is a single tilted plane. Best for a flat bed. + * + * - AUTO_BED_LEVELING_BILINEAR + * Probe several points in a grid. + * You specify the rectangle and the density of sample points. + * The result is a mesh, best for large or uneven beds. + * + * - AUTO_BED_LEVELING_UBL (Unified Bed Leveling) + * A comprehensive bed leveling system combining the features and benefits + * of other systems. UBL also includes integrated Mesh Generation, Mesh + * Validation and Mesh Editing systems. + * + * - MESH_BED_LEVELING + * Probe a grid manually + * The result is a mesh, suitable for large or uneven beds. (See BILINEAR.) + * For machines without a probe, Mesh Bed Leveling provides a method to perform + * leveling in steps so you can manually adjust the Z height at each grid-point. + * With an LCD controller the process is guided step-by-step. + */ +//#define AUTO_BED_LEVELING_3POINT +//#define AUTO_BED_LEVELING_LINEAR +//#define AUTO_BED_LEVELING_BILINEAR +//#define AUTO_BED_LEVELING_UBL +//#define MESH_BED_LEVELING + +/** + * Enable detailed logging of G28, G29, M48, etc. + * Turn on with the command 'M111 S32'. + * NOTE: Requires a lot of PROGMEM! + */ +//#define DEBUG_LEVELING_FEATURE +//#define ENABLE_MESH_EDIT_GFX_OVERLAY // enable a graphics overly while editing the mesh from auto-level + +#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_BILINEAR) || ENABLED(AUTO_BED_LEVELING_UBL) + // Gradually reduce leveling correction until a set height is reached, + // at which point movement will be level to the machine's XY plane. + // The height can be set with M420 Z + #define ENABLE_LEVELING_FADE_HEIGHT +#endif + +#if ENABLED(AUTO_BED_LEVELING_LINEAR) || ENABLED(AUTO_BED_LEVELING_BILINEAR) + + // Set the number of grid points per dimension. + #define GRID_MAX_POINTS_X 3 + #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X + + // Set the boundaries for probing (where the probe can reach). + #define LEFT_PROBE_BED_POSITION 15 + #define RIGHT_PROBE_BED_POSITION 170 + #define FRONT_PROBE_BED_POSITION 20 + #define BACK_PROBE_BED_POSITION 170 + + // The Z probe minimum outer margin (to validate G29 parameters). + #define MIN_PROBE_EDGE 10 + + // Probe along the Y axis, advancing X after each column + //#define PROBE_Y_FIRST + + #if ENABLED(AUTO_BED_LEVELING_BILINEAR) + + // Beyond the probed grid, continue the implied tilt? + // Default is to maintain the height of the nearest edge. + //#define EXTRAPOLATE_BEYOND_GRID + + // + // Experimental Subdivision of the grid by Catmull-Rom method. + // Synthesizes intermediate points to produce a more detailed mesh. + // + //#define ABL_BILINEAR_SUBDIVISION + #if ENABLED(ABL_BILINEAR_SUBDIVISION) + // Number of subdivisions between probe points + #define BILINEAR_SUBDIVISIONS 3 + #endif + + #endif + +#elif ENABLED(AUTO_BED_LEVELING_3POINT) + + // 3 arbitrary points to probe. + // A simple cross-product is used to estimate the plane of the bed. + #define ABL_PROBE_PT_1_X 15 + #define ABL_PROBE_PT_1_Y 180 + #define ABL_PROBE_PT_2_X 15 + #define ABL_PROBE_PT_2_Y 20 + #define ABL_PROBE_PT_3_X 170 + #define ABL_PROBE_PT_3_Y 20 + +#elif ENABLED(AUTO_BED_LEVELING_UBL) + + //=========================================================================== + //========================= Unified Bed Leveling ============================ + //=========================================================================== + + #define MESH_INSET 1 // Mesh inset margin on print area + #define GRID_MAX_POINTS_X 10 // Don't use more than 15 points per axis, implementation limited. + #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X + + #define UBL_PROBE_PT_1_X 39 // Probing points for 3-Point leveling of the mesh + #define UBL_PROBE_PT_1_Y 180 + #define UBL_PROBE_PT_2_X 39 + #define UBL_PROBE_PT_2_Y 20 + #define UBL_PROBE_PT_3_X 180 + #define UBL_PROBE_PT_3_Y 20 + + //#define UBL_G26_MESH_VALIDATION // Enable G26 mesh validation + #define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle + #define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500 + +#elif ENABLED(MESH_BED_LEVELING) + + //=========================================================================== + //=================================== Mesh ================================== + //=========================================================================== + + #define MESH_INSET 10 // Mesh inset margin on print area + #define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited. + #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X + + //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS + +#endif // BED_LEVELING + +/** + * Use the LCD controller for bed leveling + * Requires MESH_BED_LEVELING or PROBE_MANUALLY + */ +//#define LCD_BED_LEVELING + +#if ENABLED(LCD_BED_LEVELING) + #define MBL_Z_STEP 0.025 // Step size while manually probing Z axis. + #define LCD_PROBE_Z_RANGE 4 // Z Range centered on Z_MIN_POS for LCD Z adjustment +#endif + +// Add a menu item to move between bed corners for manual bed adjustment +//#define LEVEL_BED_CORNERS + +/** + * Commands to execute at the end of G29 probing. + * Useful to retract or move the Z probe out of the way. + */ +//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" + + +// @section homing + +// The center of the bed is at (X=0, Y=0) +//#define BED_CENTER_AT_0_0 + +// Manually set the home position. Leave these undefined for automatic settings. +// For DELTA this is the top-center of the Cartesian print volume. +//#define MANUAL_X_HOME_POS 0 +//#define MANUAL_Y_HOME_POS 0 +//#define MANUAL_Z_HOME_POS 0 + +// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area. +// +// With this feature enabled: +// +// - Allow Z homing only after X and Y homing AND stepper drivers still enabled. +// - If stepper drivers time out, it will need X and Y homing again before Z homing. +// - Move the Z probe (or nozzle) to a defined XY point before Z Homing when homing all axes (G28). +// - Prevent Z homing when the Z probe is outside bed area. +// +//#define Z_SAFE_HOMING + +#if ENABLED(Z_SAFE_HOMING) + #define Z_SAFE_HOMING_X_POINT ((X_BED_SIZE) / 2) // X point for Z homing when homing all axes (G28). + #define Z_SAFE_HOMING_Y_POINT ((Y_BED_SIZE) / 2) // Y point for Z homing when homing all axes (G28). +#endif + +// Homing speeds (mm/m) +#define HOMING_FEEDRATE_XY (50*60) +#define HOMING_FEEDRATE_Z (4*60) + +//============================================================================= +//============================= Additional Features =========================== +//============================================================================= + +// @section extras + +// +// EEPROM +// +// The microcontroller can store settings in the EEPROM, e.g. max velocity... +// M500 - stores parameters in EEPROM +// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily). +// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to. +// +#define EEPROM_SETTINGS // Enable for M500 and M501 commands +//#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release! +//#define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM. + +// +// Host Keepalive +// +// When enabled Marlin will send a busy status message to the host +// every couple of seconds when it can't accept commands. +// +#define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages +#define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113. +#define BUSY_WHILE_HEATING // Some hosts require "busy" messages even during heating + +// +// M100 Free Memory Watcher +// +//#define M100_FREE_MEMORY_WATCHER // Add M100 (Free Memory Watcher) to debug memory usage + +// +// G20/G21 Inch mode support +// +//#define INCH_MODE_SUPPORT + +// +// M149 Set temperature units support +// +#define TEMPERATURE_UNITS_SUPPORT + +// @section temperature + +// Preheat Constants +#define PREHEAT_1_TEMP_HOTEND 200 +#define PREHEAT_1_TEMP_BED 60 +#define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255 + +#define PREHEAT_2_TEMP_HOTEND 220 +#define PREHEAT_2_TEMP_BED 100 +#define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255 + +/** + * Nozzle Park -- EXPERIMENTAL + * + * Park the nozzle at the given XYZ position on idle or G27. + * + * The "P" parameter controls the action applied to the Z axis: + * + * P0 (Default) If Z is below park Z raise the nozzle. + * P1 Raise the nozzle always to Z-park height. + * P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS. + */ +//#define NOZZLE_PARK_FEATURE + +#if ENABLED(NOZZLE_PARK_FEATURE) + // Specify a park position as { X, Y, Z } + #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 } +#endif + +/** + * Clean Nozzle Feature -- EXPERIMENTAL + * + * Adds the G12 command to perform a nozzle cleaning process. + * + * Parameters: + * P Pattern + * S Strokes / Repetitions + * T Triangles (P1 only) + * + * Patterns: + * P0 Straight line (default). This process requires a sponge type material + * at a fixed bed location. "S" specifies strokes (i.e. back-forth motions) + * between the start / end points. + * + * P1 Zig-zag pattern between (X0, Y0) and (X1, Y1), "T" specifies the + * number of zig-zag triangles to do. "S" defines the number of strokes. + * Zig-zags are done in whichever is the narrower dimension. + * For example, "G12 P1 S1 T3" will execute: + * + * -- + * | (X0, Y1) | /\ /\ /\ | (X1, Y1) + * | | / \ / \ / \ | + * A | | / \ / \ / \ | + * | | / \ / \ / \ | + * | (X0, Y0) | / \/ \/ \ | (X1, Y0) + * -- +--------------------------------+ + * |________|_________|_________| + * T1 T2 T3 + * + * P2 Circular pattern with middle at NOZZLE_CLEAN_CIRCLE_MIDDLE. + * "R" specifies the radius. "S" specifies the stroke count. + * Before starting, the nozzle moves to NOZZLE_CLEAN_START_POINT. + * + * Caveats: The ending Z should be the same as starting Z. + * Attention: EXPERIMENTAL. G-code arguments may change. + * + */ +//#define NOZZLE_CLEAN_FEATURE + +#if ENABLED(NOZZLE_CLEAN_FEATURE) + // Default number of pattern repetitions + #define NOZZLE_CLEAN_STROKES 12 + + // Default number of triangles + #define NOZZLE_CLEAN_TRIANGLES 3 + + // Specify positions as { X, Y, Z } + #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)} + #define NOZZLE_CLEAN_END_POINT {100, 60, (Z_MIN_POS + 1)} + + // Circular pattern radius + #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5 + // Circular pattern circle fragments number + #define NOZZLE_CLEAN_CIRCLE_FN 10 + // Middle point of circle + #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT + + // Moves the nozzle to the initial position + #define NOZZLE_CLEAN_GOBACK +#endif + +/** + * Print Job Timer + * + * Automatically start and stop the print job timer on M104/M109/M190. + * + * M104 (hotend, no wait) - high temp = none, low temp = stop timer + * M109 (hotend, wait) - high temp = start timer, low temp = stop timer + * M190 (bed, wait) - high temp = start timer, low temp = none + * + * The timer can also be controlled with the following commands: + * + * M75 - Start the print job timer + * M76 - Pause the print job timer + * M77 - Stop the print job timer + */ +#define PRINTJOB_TIMER_AUTOSTART + +/** + * Print Counter + * + * Track statistical data such as: + * + * - Total print jobs + * - Total successful print jobs + * - Total failed print jobs + * - Total time printing + * + * View the current statistics with M78. + */ +//#define PRINTCOUNTER + +//============================================================================= +//============================= LCD and SD support ============================ +//============================================================================= + +// @section lcd + +/** + * LCD LANGUAGE + * + * Select the language to display on the LCD. These languages are available: + * + * en, an, bg, ca, cn, cz, cz_utf8, de, el, el-gr, es, eu, fi, fr, fr_utf8, gl, + * hr, it, kana, kana_utf8, nl, pl, pt, pt_utf8, pt-br, pt-br_utf8, ru, sk_utf8, + * tr, uk, zh_CN, zh_TW, test + * + * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cn':'Chinese', 'cz':'Czech', 'cz_utf8':'Czech (UTF8)', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'fr_utf8':'French (UTF8)', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'kana':'Japanese', 'kana_utf8':'Japanese (UTF8)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'pt-br_utf8':'Portuguese (Brazilian UTF8)', 'pt_utf8':'Portuguese (UTF8)', 'ru':'Russian', 'sk_utf8':'Slovak (UTF8)', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Taiwan)', test':'TEST' } + */ +#define LCD_LANGUAGE en + +/** + * LCD Character Set + * + * Note: This option is NOT applicable to Graphical Displays. + * + * All character-based LCDs provide ASCII plus one of these + * language extensions: + * + * - JAPANESE ... the most common + * - WESTERN ... with more accented characters + * - CYRILLIC ... for the Russian language + * + * To determine the language extension installed on your controller: + * + * - Compile and upload with LCD_LANGUAGE set to 'test' + * - Click the controller to view the LCD menu + * - The LCD will display Japanese, Western, or Cyrillic text + * + * See http://marlinfw.org/docs/development/lcd_language.html + * + * :['JAPANESE', 'WESTERN', 'CYRILLIC'] + */ +#define DISPLAY_CHARSET_HD44780 JAPANESE + +/** + * LCD TYPE + * + * Enable ULTRA_LCD for a 16x2, 16x4, 20x2, or 20x4 character-based LCD. + * Enable DOGLCD for a 128x64 (ST7565R) Full Graphical Display. + * (These options will be enabled automatically for most displays.) + * + * IMPORTANT: The U8glib library is required for Full Graphic Display! + * https://github.com/olikraus/U8glib_Arduino + */ +//#define ULTRA_LCD // Character based +//#define DOGLCD // Full graphics display + +/** + * SD CARD + * + * SD Card support is disabled by default. If your controller has an SD slot, + * you must uncomment the following option or it won't work. + * + */ +#define SDSUPPORT + +/** + * SD CARD: SPI SPEED + * + * Enable one of the following items for a slower SPI transfer speed. + * This may be required to resolve "volume init" errors. + */ +//#define SPI_SPEED SPI_HALF_SPEED +//#define SPI_SPEED SPI_QUARTER_SPEED +//#define SPI_SPEED SPI_EIGHTH_SPEED + +/** + * SD CARD: ENABLE CRC + * + * Use CRC checks and retries on the SD communication. + */ +//#define SD_CHECK_AND_RETRY + +// +// ENCODER SETTINGS +// +// This option overrides the default number of encoder pulses needed to +// produce one step. Should be increased for high-resolution encoders. +// +//#define ENCODER_PULSES_PER_STEP 1 + +// +// Use this option to override the number of step signals required to +// move between next/prev menu items. +// +//#define ENCODER_STEPS_PER_MENU_ITEM 5 + +/** + * Encoder Direction Options + * + * Test your encoder's behavior first with both options disabled. + * + * Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION. + * Reversed Menu Navigation only? Enable REVERSE_MENU_DIRECTION. + * Reversed Value Editing only? Enable BOTH options. + */ + +// +// This option reverses the encoder direction everywhere. +// +// Set this option if CLOCKWISE causes values to DECREASE +// +//#define REVERSE_ENCODER_DIRECTION + +// +// This option reverses the encoder direction for navigating LCD menus. +// +// If CLOCKWISE normally moves DOWN this makes it go UP. +// If CLOCKWISE normally moves UP this makes it go DOWN. +// +//#define REVERSE_MENU_DIRECTION + +// +// Individual Axis Homing +// +// Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu. +// +//#define INDIVIDUAL_AXIS_HOMING_MENU + +// +// SPEAKER/BUZZER +// +// If you have a speaker that can produce tones, enable it here. +// By default Marlin assumes you have a buzzer with a fixed frequency. +// +//#define SPEAKER + +// +// The duration and frequency for the UI feedback sound. +// Set these to 0 to disable audio feedback in the LCD menus. +// +// Note: Test audio output with the G-Code: +// M300 S P +// +//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 +//#define LCD_FEEDBACK_FREQUENCY_HZ 1000 + +// +// CONTROLLER TYPE: Standard +// +// Marlin supports a wide variety of controllers. +// Enable one of the following options to specify your controller. +// + +// +// ULTIMAKER Controller. +// +//#define ULTIMAKERCONTROLLER + +// +// ULTIPANEL as seen on Thingiverse. +// +//#define ULTIPANEL + +// +// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3) +// http://reprap.org/wiki/PanelOne +// +//#define PANEL_ONE + +// +// MaKr3d Makr-Panel with graphic controller and SD support. +// http://reprap.org/wiki/MaKr3d_MaKrPanel +// +//#define MAKRPANEL + +// +// ReprapWorld Graphical LCD +// https://reprapworld.com/?products_details&products_id/1218 +// +//#define REPRAPWORLD_GRAPHICAL_LCD + +// +// Activate one of these if you have a Panucatt Devices +// Viki 2.0 or mini Viki with Graphic LCD +// http://panucatt.com +// +//#define VIKI2 +//#define miniVIKI + +// +// Adafruit ST7565 Full Graphic Controller. +// https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/ +// +//#define ELB_FULL_GRAPHIC_CONTROLLER + +// +// RepRapDiscount Smart Controller. +// http://reprap.org/wiki/RepRapDiscount_Smart_Controller +// +// Note: Usually sold with a white PCB. +// +//#define REPRAP_DISCOUNT_SMART_CONTROLLER + +// +// GADGETS3D G3D LCD/SD Controller +// http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel +// +// Note: Usually sold with a blue PCB. +// +//#define G3D_PANEL + +// +// RepRapDiscount FULL GRAPHIC Smart Controller +// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller +// +//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER + +// +// MakerLab Mini Panel with graphic +// controller and SD support - http://reprap.org/wiki/Mini_panel +// +//#define MINIPANEL + +// +// RepRapWorld REPRAPWORLD_KEYPAD v1.1 +// http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626 +// +// REPRAPWORLD_KEYPAD_MOVE_STEP sets how much should the robot move when a key +// is pressed, a value of 10.0 means 10mm per click. +// +//#define REPRAPWORLD_KEYPAD +//#define REPRAPWORLD_KEYPAD_MOVE_STEP 1.0 + +// +// RigidBot Panel V1.0 +// http://www.inventapart.com/ +// +//#define RIGIDBOT_PANEL + +// +// BQ LCD Smart Controller shipped by +// default with the BQ Hephestos 2 and Witbox 2. +// +//#define BQ_LCD_SMART_CONTROLLER + +// +// Cartesio UI +// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface +// +//#define CARTESIO_UI + +// +// ANET_10 Controller supported displays. +// +//#define ANET_KEYPAD_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin. + // This LCD is known to be susceptible to electrical interference + // which scrambles the display. Pressing any button clears it up. +//#define ANET_FULL_GRAPHICS_LCD // Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6 + // A clone of the RepRapDiscount full graphics display but with + // different pins/wiring (see pins_ANET_10.h). + +// +// LCD for Melzi Card with Graphical LCD +// +//#define LCD_FOR_MELZI + +// +// CONTROLLER TYPE: I2C +// +// Note: These controllers require the installation of Arduino's LiquidCrystal_I2C +// library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C +// + +// +// Elefu RA Board Control Panel +// http://www.elefu.com/index.php?route=product/product&product_id=53 +// +//#define RA_CONTROL_PANEL + +// +// Sainsmart YW Robot (LCM1602) LCD Display +// +// Note: This controller requires F.Malpartida's LiquidCrystal_I2C library +// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home +// +//#define LCD_I2C_SAINSMART_YWROBOT + +// +// Generic LCM1602 LCD adapter +// +//#define LCM1602 + +// +// PANELOLU2 LCD with status LEDs, +// separate encoder and click inputs. +// +// Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later. +// For more info: https://github.com/lincomatic/LiquidTWI2 +// +// Note: The PANELOLU2 encoder click input can either be directly connected to +// a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1). +// +//#define LCD_I2C_PANELOLU2 + +// +// Panucatt VIKI LCD with status LEDs, +// integrated click & L/R/U/D buttons, separate encoder inputs. +// +//#define LCD_I2C_VIKI + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + //#define U8GLIB_SSD1306 + #define U8GLIB_SH1106 +#endif + +// +// CONTROLLER TYPE: Shift register panels +// +// 2 wire Non-latching LCD SR from https://goo.gl/aJJ4sH +// LCD configuration: http://reprap.org/wiki/SAV_3D_LCD +// +//#define SAV_3DLCD + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// MKS MINI12864 with graphic controller and SD support +// http://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED + +// +// AZSMZ 12864 LCD with SD +// https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html +// +//#define AZSMZ_12864 + +// Silvergate GLCD controller +// http://github.com/android444/Silvergate +// +//#define SILVER_GATE_GLCD_CONTROLLER + +//============================================================================= +//=============================== Extra Features ============================== +//============================================================================= + +// @section extras + +// Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino +//#define FAST_PWM_FAN + +// Use software PWM to drive the fan, as for the heaters. This uses a very low frequency +// which is not as annoying as with the hardware PWM. On the other hand, if this frequency +// is too low, you should also increment SOFT_PWM_SCALE. +//#define FAN_SOFT_PWM + +// Incrementing this by 1 will double the software PWM frequency, +// affecting heaters, and the fan if FAN_SOFT_PWM is enabled. +// However, control resolution will be halved for each increment; +// at zero value, there are 128 effective control positions. +#define SOFT_PWM_SCALE 0 + +// If SOFT_PWM_SCALE is set to a value higher than 0, dithering can +// be used to mitigate the associated resolution loss. If enabled, +// some of the PWM cycles are stretched so on average the desired +// duty cycle is attained. +//#define SOFT_PWM_DITHER + +// Temperature status LEDs that display the hotend and bed temperature. +// If all hotends, bed temperature, and target temperature are under 54C +// then the BLUE led is on. Otherwise the RED led is on. (1C hysteresis) +//#define TEMP_STAT_LEDS + +// M240 Triggers a camera by emulating a Canon RC-1 Remote +// Data from: http://www.doc-diy.net/photo/rc-1_hacked/ +//#define PHOTOGRAPH_PIN 23 + +// SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure +//#define SF_ARC_FIX + +// Support for the BariCUDA Paste Extruder +//#define BARICUDA + +// Support for BlinkM/CyzRgb +//#define BLINKM + +// Support for PCA9632 PWM LED driver +//#define PCA9632 + +/** + * RGB LED / LED Strip Control + * + * Enable support for an RGB LED connected to 5V digital pins, or + * an RGB Strip connected to MOSFETs controlled by digital pins. + * + * Adds the M150 command to set the LED (or LED strip) color. + * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of + * luminance values can be set from 0 to 255. + * For Neopixel LED an overall brightness parameter is also available. + * + * *** CAUTION *** + * LED Strips require a MOFSET Chip between PWM lines and LEDs, + * as the Arduino cannot handle the current the LEDs will require. + * Failure to follow this precaution can destroy your Arduino! + * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * more current than the Arduino 5V linear regulator can produce. + * *** CAUTION *** + * + * LED Type. Enable only one of the following two options. + * + */ + +//#define RGB_LED +//#define RGBW_LED +#if ENABLED(RGB_LED) || ENABLED(RGBW_LED) + #define RGB_LED_R_PIN 34 + #define RGB_LED_G_PIN 43 + #define RGB_LED_B_PIN 35 + #define RGB_LED_W_PIN -1 +#endif + +// Support for Adafruit Neopixel LED driver +//#define NEOPIXEL_LED +#if ENABLED(NEOPIXEL_LED) + #define NEOPIXEL_TYPE NEO_GRB // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) + #define NEOPIXEL_PIN 4 // LED driving pin on motherboard 4 => D4 (EXP2-5 on Printrboard) / 30 => PC7 (EXP3-13 on Rumba) + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. + #define NEOPIXEL_BRIGHTNESS 255 // Initial brightness 0-255 + //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup +#endif + +/** + * Printer Event LEDs + * + * During printing, the LEDs will reflect the printer status: + * + * - Gradually change from blue to violet as the heated bed gets to target temp + * - Gradually change from violet to red as the hotend gets to temperature + * - Change to white to illuminate work surface + * - Change to green once print has finished + * - Turn off after the print has finished and the user has pushed a button + */ +#if ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED) + #define PRINTER_EVENT_LEDS +#endif + +/** + * R/C SERVO support + * Sponsored by TrinityLabs, Reworked by codexmas + */ + +/** + * Number of servos + * + * For some servo-related options NUM_SERVOS will be set automatically. + * Set this manually if there are extra servos needing manual control. + * Leave undefined or set to 0 to entirely disable the servo subsystem. + */ +//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command + +// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. +// 300ms is a good value but you can try less delay. +// If the servo can't reach the requested position, increase it. +#define SERVO_DELAY { 300 } + +// Servo deactivation +// +// With this option servos are powered only during movement, then turned off to prevent jitter. +//#define DEACTIVATE_SERVOS_AFTER_MOVE + +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 // (mm) Diameter of the filament generally used (3.0 or 1.75mm), also used in the slicer. Used to validate sensor reading. + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor (0,1,2,3) + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define MEASURED_UPPER_LIMIT 3.30 // (mm) Upper limit used to validate sensor reading + #define MEASURED_LOWER_LIMIT 1.90 // (mm) Lower limit used to validate sensor reading + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + +#endif // CONFIGURATION_H diff --git a/Marlin/src/config/examples/Sanguinololu/Configuration.h b/Marlin/src/config/examples/Sanguinololu/Configuration.h index eb1122a7b6..37c21adb0f 100644 --- a/Marlin/src/config/examples/Sanguinololu/Configuration.h +++ b/Marlin/src/config/examples/Sanguinololu/Configuration.h @@ -94,11 +94,11 @@ // @section machine /** - * Select which serial port on the board will be used for communication with the host. + * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port 0 is always used by the Arduino bootloader regardless of this setting. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * - * :[0, 1, 2, 3, 4, 5, 6, 7] + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT 0 diff --git a/Marlin/src/config/examples/TinyBoy2/Configuration.h b/Marlin/src/config/examples/TinyBoy2/Configuration.h index 3f57f70c1f..60fb7a2931 100644 --- a/Marlin/src/config/examples/TinyBoy2/Configuration.h +++ b/Marlin/src/config/examples/TinyBoy2/Configuration.h @@ -110,11 +110,11 @@ // @section machine /** - * Select which serial port on the board will be used for communication with the host. + * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port 0 is always used by the Arduino bootloader regardless of this setting. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * - * :[0, 1, 2, 3, 4, 5, 6, 7] + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT 0 diff --git a/Marlin/src/config/examples/Velleman/K8200/Configuration.h b/Marlin/src/config/examples/Velleman/K8200/Configuration.h index fd54f271b1..7d0d83a378 100644 --- a/Marlin/src/config/examples/Velleman/K8200/Configuration.h +++ b/Marlin/src/config/examples/Velleman/K8200/Configuration.h @@ -110,11 +110,11 @@ // @section machine /** - * Select which serial port on the board will be used for communication with the host. + * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port 0 is always used by the Arduino bootloader regardless of this setting. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * - * :[0, 1, 2, 3, 4, 5, 6, 7] + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT 0 diff --git a/Marlin/src/config/examples/Velleman/K8400/Configuration.h b/Marlin/src/config/examples/Velleman/K8400/Configuration.h index 826791d754..734ddfbf2b 100644 --- a/Marlin/src/config/examples/Velleman/K8400/Configuration.h +++ b/Marlin/src/config/examples/Velleman/K8400/Configuration.h @@ -94,11 +94,11 @@ // @section machine /** - * Select which serial port on the board will be used for communication with the host. + * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port 0 is always used by the Arduino bootloader regardless of this setting. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * - * :[0, 1, 2, 3, 4, 5, 6, 7] + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT 0 diff --git a/Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h b/Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h index c2973cced4..4733e462f1 100644 --- a/Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h +++ b/Marlin/src/config/examples/Velleman/K8400/Dual-head/Configuration.h @@ -94,11 +94,11 @@ // @section machine /** - * Select which serial port on the board will be used for communication with the host. + * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port 0 is always used by the Arduino bootloader regardless of this setting. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * - * :[0, 1, 2, 3, 4, 5, 6, 7] + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT 0 diff --git a/Marlin/src/config/examples/adafruit/ST7565/Configuration.h b/Marlin/src/config/examples/adafruit/ST7565/Configuration.h index 6b5d9ed2a7..16e1acdef8 100644 --- a/Marlin/src/config/examples/adafruit/ST7565/Configuration.h +++ b/Marlin/src/config/examples/adafruit/ST7565/Configuration.h @@ -94,11 +94,11 @@ // @section machine /** - * Select which serial port on the board will be used for communication with the host. + * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port 0 is always used by the Arduino bootloader regardless of this setting. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * - * :[0, 1, 2, 3, 4, 5, 6, 7] + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT 0 diff --git a/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h b/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h index 8709803665..e18dae48a7 100644 --- a/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h +++ b/Marlin/src/config/examples/delta/FLSUN/auto_calibrate/Configuration.h @@ -94,11 +94,11 @@ // @section machine /** - * Select which serial port on the board will be used for communication with the host. + * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port 0 is always used by the Arduino bootloader regardless of this setting. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * - * :[0, 1, 2, 3, 4, 5, 6, 7] + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT 0 diff --git a/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h b/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h index 4bc281ca71..31b7fdc051 100644 --- a/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h +++ b/Marlin/src/config/examples/delta/FLSUN/kossel_mini/Configuration.h @@ -94,11 +94,11 @@ // @section machine /** - * Select which serial port on the board will be used for communication with the host. + * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port 0 is always used by the Arduino bootloader regardless of this setting. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * - * :[0, 1, 2, 3, 4, 5, 6, 7] + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT 0 diff --git a/Marlin/src/config/examples/delta/generic/Configuration.h b/Marlin/src/config/examples/delta/generic/Configuration.h index 589f269133..b532a896dd 100644 --- a/Marlin/src/config/examples/delta/generic/Configuration.h +++ b/Marlin/src/config/examples/delta/generic/Configuration.h @@ -94,11 +94,11 @@ // @section machine /** - * Select which serial port on the board will be used for communication with the host. + * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port 0 is always used by the Arduino bootloader regardless of this setting. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * - * :[0, 1, 2, 3, 4, 5, 6, 7] + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT 0 diff --git a/Marlin/src/config/examples/delta/kossel_mini/Configuration.h b/Marlin/src/config/examples/delta/kossel_mini/Configuration.h index 4925e632a8..82928f67b8 100644 --- a/Marlin/src/config/examples/delta/kossel_mini/Configuration.h +++ b/Marlin/src/config/examples/delta/kossel_mini/Configuration.h @@ -94,11 +94,11 @@ // @section machine /** - * Select which serial port on the board will be used for communication with the host. + * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port 0 is always used by the Arduino bootloader regardless of this setting. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * - * :[0, 1, 2, 3, 4, 5, 6, 7] + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT 0 diff --git a/Marlin/src/config/examples/delta/kossel_pro/Configuration.h b/Marlin/src/config/examples/delta/kossel_pro/Configuration.h index a7d1441880..5aebe5aefb 100644 --- a/Marlin/src/config/examples/delta/kossel_pro/Configuration.h +++ b/Marlin/src/config/examples/delta/kossel_pro/Configuration.h @@ -98,11 +98,11 @@ // @section machine /** - * Select which serial port on the board will be used for communication with the host. + * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port 0 is always used by the Arduino bootloader regardless of this setting. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * - * :[0, 1, 2, 3, 4, 5, 6, 7] + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT 0 diff --git a/Marlin/src/config/examples/delta/kossel_xl/Configuration.h b/Marlin/src/config/examples/delta/kossel_xl/Configuration.h index 4ff579dcb7..8ffa56a4aa 100644 --- a/Marlin/src/config/examples/delta/kossel_xl/Configuration.h +++ b/Marlin/src/config/examples/delta/kossel_xl/Configuration.h @@ -94,11 +94,11 @@ // @section machine /** - * Select which serial port on the board will be used for communication with the host. + * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port 0 is always used by the Arduino bootloader regardless of this setting. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * - * :[0, 1, 2, 3, 4, 5, 6, 7] + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT 0 diff --git a/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h b/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h index 1c170fb248..e6899922f6 100644 --- a/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h +++ b/Marlin/src/config/examples/gCreate/gMax1.5+/Configuration.h @@ -94,11 +94,11 @@ // @section machine /** - * Select which serial port on the board will be used for communication with the host. + * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port 0 is always used by the Arduino bootloader regardless of this setting. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * - * :[0, 1, 2, 3, 4, 5, 6, 7] + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT 0 diff --git a/Marlin/src/config/examples/makibox/Configuration.h b/Marlin/src/config/examples/makibox/Configuration.h index 47f169eab3..1352d10426 100644 --- a/Marlin/src/config/examples/makibox/Configuration.h +++ b/Marlin/src/config/examples/makibox/Configuration.h @@ -94,11 +94,11 @@ // @section machine /** - * Select which serial port on the board will be used for communication with the host. + * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port 0 is always used by the Arduino bootloader regardless of this setting. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * - * :[0, 1, 2, 3, 4, 5, 6, 7] + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT 0 diff --git a/Marlin/src/config/examples/stm32f103ret6/Configuration.h b/Marlin/src/config/examples/stm32f103ret6/Configuration.h index 2cf32ca0c9..90f0c67bc9 100644 --- a/Marlin/src/config/examples/stm32f103ret6/Configuration.h +++ b/Marlin/src/config/examples/stm32f103ret6/Configuration.h @@ -94,11 +94,11 @@ // @section machine /** - * Select which serial port on the board will be used for communication with the host. + * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port 0 is always used by the Arduino bootloader regardless of this setting. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * - * :[0, 1, 2, 3, 4, 5, 6, 7] + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT 0 diff --git a/Marlin/src/config/examples/tvrrug/Round2/Configuration.h b/Marlin/src/config/examples/tvrrug/Round2/Configuration.h index 87411e2c4f..d302d1d43b 100644 --- a/Marlin/src/config/examples/tvrrug/Round2/Configuration.h +++ b/Marlin/src/config/examples/tvrrug/Round2/Configuration.h @@ -94,11 +94,11 @@ // @section machine /** - * Select which serial port on the board will be used for communication with the host. + * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port 0 is always used by the Arduino bootloader regardless of this setting. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * - * :[0, 1, 2, 3, 4, 5, 6, 7] + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT 0 diff --git a/Marlin/src/config/examples/wt150/Configuration.h b/Marlin/src/config/examples/wt150/Configuration.h index 409be5e180..41b91fec06 100644 --- a/Marlin/src/config/examples/wt150/Configuration.h +++ b/Marlin/src/config/examples/wt150/Configuration.h @@ -94,11 +94,11 @@ // @section machine /** - * Select which serial port on the board will be used for communication with the host. + * Select the serial port on the board to use for communication with the host. * This allows the connection of wireless adapters (for instance) to non-default port pins. - * Serial port 0 is always used by the Arduino bootloader regardless of this setting. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. * - * :[0, 1, 2, 3, 4, 5, 6, 7] + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ #define SERIAL_PORT 0 diff --git a/Marlin/src/inc/Conditionals_LCD.h b/Marlin/src/inc/Conditionals_LCD.h index 0eeabdd99b..a25d45cecc 100644 --- a/Marlin/src/inc/Conditionals_LCD.h +++ b/Marlin/src/inc/Conditionals_LCD.h @@ -491,12 +491,10 @@ #define HAS_RESUME_CONTINUE (ENABLED(NEWPANEL) || ENABLED(EMERGENCY_PARSER)) #define HAS_COLOR_LEDS (ENABLED(BLINKM) || ENABLED(RGB_LED) || ENABLED(RGBW_LED) || ENABLED(PCA9632) || ENABLED(NEOPIXEL_LED)) - // For Re-ARM boards, always use the USB Emulated Serial Port unless RE_ARM_FORCE_SERIAL_PORT is defined - #if MB(RAMPS_14_RE_ARM_EFB) || MB(RAMPS_14_RE_ARM_EEB) || MB(RAMPS_14_RE_ARM_EFF) || MB(RAMPS_14_RE_ARM_EEF) || MB(RAMPS_14_RE_ARM_SF) - #ifndef RE_ARM_FORCE_SERIAL_PORT - #undef SERIAL_PORT - #define SERIAL_PORT -1 - #endif - #endif +// For Re-ARM boards, always use the USB Emulated Serial Port unless RE_ARM_FORCE_SERIAL_PORT is defined +#if !defined(RE_ARM_FORCE_SERIAL_PORT) && (MB(RAMPS_14_RE_ARM_EFB) || MB(RAMPS_14_RE_ARM_EEB) || MB(RAMPS_14_RE_ARM_EFF) || MB(RAMPS_14_RE_ARM_EEF) || MB(RAMPS_14_RE_ARM_SF)) + #undef SERIAL_PORT + #define SERIAL_PORT -1 +#endif #endif // CONDITIONALS_LCD_H