zaubentrucker/muele-marlin
1
0
Fork 0
Code Issues Pull requests Actions Packages Projects Releases Wiki Activity

Merge pull request #4789 from thinkyhead/rc_better_leveling_etc

Browse source 
Various cleanups ahead of more…
This commit is contained in:
Scott Lahteine 2016-09-13 05:21:17 -05:00 committed by GitHub
parent 0ea7ed6db6 9b0931ef74
commit 94d5cf8721
35 changed files with 1743 additions and 1394 deletions
Show stats Download patch file Download diff file Expand all files Collapse all files

52
Marlin/Conditionals_post.h
View file

@ -61,12 +61,16 @@
#define NORMAL_AXIS X_AXIS
#endif
#define IS_SCARA (ENABLED(MORGAN_SCARA) || ENABLED(MAKERARM_SCARA))
#define IS_KINEMATIC (ENABLED(DELTA) || IS_SCARA)
#define IS_CARTESIAN !IS_KINEMATIC
/**
* SCARA
* SCARA cannot use SLOWDOWN and requires QUICKHOME
*/
#if ENABLED(SCARA)
#if IS_SCARA
#undef SLOWDOWN
#define QUICK_HOME //SCARA needs Quickhome
#define QUICK_HOME
#endif
/**
@ -132,12 +136,6 @@
#define HOMING_Z_WITH_PROBE (HAS_BED_PROBE && Z_HOME_DIR < 0 && ENABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN))
// Boundaries for probing based on set limits
#define MIN_PROBE_X (max(X_MIN_POS, X_MIN_POS + X_PROBE_OFFSET_FROM_EXTRUDER))
#define MAX_PROBE_X (min(X_MAX_POS, X_MAX_POS + X_PROBE_OFFSET_FROM_EXTRUDER))
#define MIN_PROBE_Y (max(Y_MIN_POS, Y_MIN_POS + Y_PROBE_OFFSET_FROM_EXTRUDER))
#define MAX_PROBE_Y (min(Y_MAX_POS, Y_MAX_POS + Y_PROBE_OFFSET_FROM_EXTRUDER))
#define HAS_Z_SERVO_ENDSTOP (defined(Z_ENDSTOP_SERVO_NR) && Z_ENDSTOP_SERVO_NR >= 0)
/**
@ -657,18 +655,28 @@
#ifndef DELTA_DIAGONAL_ROD_TRIM_TOWER_3
#define DELTA_DIAGONAL_ROD_TRIM_TOWER_3 0.0
#endif
#if ENABLED(AUTO_BED_LEVELING_GRID)
#define DELTA_BED_LEVELING_GRID
#endif
#endif
/**
* When not using other bed leveling...
* Specify the exact style of auto bed leveling
*
* 3POINT - 3 Point Probing with the least-squares solution.
* LINEAR - Grid Probing with the least-squares solution.
* NONLINEAR - Grid Probing with a mesh solution. Best for large beds.
*/
#if ENABLED(AUTO_BED_LEVELING_FEATURE) && DISABLED(AUTO_BED_LEVELING_GRID) && DISABLED(DELTA_BED_LEVELING_GRID)
#define AUTO_BED_LEVELING_3POINT
#if ENABLED(AUTO_BED_LEVELING_FEATURE)
#if DISABLED(AUTO_BED_LEVELING_GRID)
#define AUTO_BED_LEVELING_LINEAR
#define AUTO_BED_LEVELING_3POINT
#elif IS_KINEMATIC
#define AUTO_BED_LEVELING_NONLINEAR
#else
#define AUTO_BED_LEVELING_LINEAR
#endif
#endif
#define PLANNER_LEVELING (ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_LINEAR))
/**
* Buzzer/Speaker
*/
@ -702,4 +710,18 @@
#define Z_PROBE_TRAVEL_HEIGHT Z_HOMING_HEIGHT
#endif
#if IS_KINEMATIC
// Check for this in the code instead
#define MIN_PROBE_X X_MIN_POS
#define MAX_PROBE_X X_MAX_POS
#define MIN_PROBE_Y Y_MIN_POS
#define MAX_PROBE_Y Y_MAX_POS
#else
// Boundaries for probing based on set limits
#define MIN_PROBE_X (max(X_MIN_POS, X_MIN_POS + X_PROBE_OFFSET_FROM_EXTRUDER))
#define MAX_PROBE_X (min(X_MAX_POS, X_MAX_POS + X_PROBE_OFFSET_FROM_EXTRUDER))
#define MIN_PROBE_Y (max(Y_MIN_POS, Y_MIN_POS + Y_PROBE_OFFSET_FROM_EXTRUDER))
#define MAX_PROBE_Y (min(Y_MAX_POS, Y_MAX_POS + Y_PROBE_OFFSET_FROM_EXTRUDER))
#endif
#endif // CONDITIONALS_POST_H

16
Marlin/Configuration_adv.h
View file

@ -168,14 +168,16 @@
// @section extruder
// extruder run-out prevention.
//if the machine is idle, and the temperature over MINTEMP, every couple of SECONDS some filament is extruded
// Extruder runout prevention.
// If the machine is idle and the temperature over MINTEMP
// then extrude some filament every couple of SECONDS.
//#define EXTRUDER_RUNOUT_PREVENT
#define EXTRUDER_RUNOUT_MINTEMP 190
#define EXTRUDER_RUNOUT_SECONDS 30
#define EXTRUDER_RUNOUT_ESTEPS 14 // mm filament
#define EXTRUDER_RUNOUT_SPEED 1500 // extrusion speed
#define EXTRUDER_RUNOUT_EXTRUDE 100
#if ENABLED(EXTRUDER_RUNOUT_PREVENT)
#define EXTRUDER_RUNOUT_MINTEMP 190
#define EXTRUDER_RUNOUT_SECONDS 30
#define EXTRUDER_RUNOUT_SPEED 1500 // mm/m
#define EXTRUDER_RUNOUT_EXTRUDE 5 // mm
#endif
// @section temperature

42
Marlin/Marlin.h
View file

@ -220,7 +220,6 @@ void disable_all_steppers();
void FlushSerialRequestResend();
void ok_to_send();
void reset_bed_level();
void kill(const char*);
void quickstop_stepper();
@ -266,6 +265,10 @@ extern bool axis_known_position[XYZ]; // axis[n].is_known
extern bool axis_homed[XYZ]; // axis[n].is_homed
extern volatile bool wait_for_heatup;
#if ENABLED(EMERGENCY_PARSER) && DISABLED(ULTIPANEL)
extern volatile bool wait_for_user;
#endif
extern float current_position[NUM_AXIS];
extern float position_shift[XYZ];
extern float home_offset[XYZ];
@ -298,26 +301,29 @@ int code_value_int();
float code_value_temp_abs();
float code_value_temp_diff();
#if IS_KINEMATIC
extern float delta[ABC];
void inverse_kinematics(const float cartesian[XYZ]);
#endif
#if ENABLED(DELTA)
extern float delta[ABC];
extern float endstop_adj[ABC]; // axis[n].endstop_adj
extern float delta_radius;
extern float delta_diagonal_rod;
extern float delta_segments_per_second;
extern float delta_diagonal_rod_trim_tower_1;
extern float delta_diagonal_rod_trim_tower_2;
extern float delta_diagonal_rod_trim_tower_3;
void inverse_kinematics(const float cartesian[XYZ]);
extern float delta[ABC],
endstop_adj[ABC],
delta_radius,
delta_diagonal_rod,
delta_segments_per_second,
delta_diagonal_rod_trim_tower_1,
delta_diagonal_rod_trim_tower_2,
delta_diagonal_rod_trim_tower_3;
void recalc_delta_settings(float radius, float diagonal_rod);
#if ENABLED(AUTO_BED_LEVELING_FEATURE)
extern int delta_grid_spacing[2];
void adjust_delta(float cartesian[XYZ]);
#endif
#elif ENABLED(SCARA)
extern float delta[ABC];
#elif IS_SCARA
extern float axis_scaling[ABC]; // Build size scaling
void inverse_kinematics(const float cartesian[XYZ]);
void forward_kinematics_SCARA(float f_scara[ABC]);
void forward_kinematics_SCARA(const float &a, const float &b);
#endif
#if ENABLED(AUTO_BED_LEVELING_NONLINEAR)
extern int nonlinear_grid_spacing[2];
void adjust_delta(float cartesian[XYZ]);
#endif
#if ENABLED(Z_DUAL_ENDSTOPS)

3
Marlin/MarlinSerial.cpp
View file

@ -509,6 +509,9 @@ MarlinSerial customizedSerial;
switch (state) {
case state_M108:
wait_for_heatup = false;
#if DISABLED(ULTIPANEL)
wait_for_user = false;
#endif
break;
case state_M112:
kill(PSTR(MSG_KILLED));

2291
Marlin/Marlin_main.cpp
View file

File diff suppressed because it is too large Load diff

181
Marlin/SanityCheck.h
View file

@ -137,6 +137,8 @@
#error Please replace "const int dropsegments" with "#define MIN_STEPS_PER_SEGMENT" (and increase by 1) in Configuration_adv.h.
#elif defined(PREVENT_DANGEROUS_EXTRUDE)
#error "PREVENT_DANGEROUS_EXTRUDE is now PREVENT_COLD_EXTRUSION. Please update your configuration."
#elif defined(SCARA)
#error "SCARA is now MORGAN_SCARA. Please update your configuration."
#endif
/**
@ -179,11 +181,9 @@
#if ENABLED(LCD_PROGRESS_BAR)
#if DISABLED(SDSUPPORT)
#error "LCD_PROGRESS_BAR requires SDSUPPORT."
#endif
#if ENABLED(DOGLCD)
#elif ENABLED(DOGLCD)
#error "LCD_PROGRESS_BAR does not apply to graphical displays."
#endif
#if ENABLED(FILAMENT_LCD_DISPLAY)
#elif ENABLED(FILAMENT_LCD_DISPLAY)
#error "LCD_PROGRESS_BAR and FILAMENT_LCD_DISPLAY are not fully compatible. Comment out this line to use both."
#endif
#endif
@ -573,11 +573,39 @@
/**
* Don't set more than one kinematic type
*/
#if (ENABLED(DELTA) && (ENABLED(SCARA) || ENABLED(COREXY) || ENABLED(COREXZ) || ENABLED(COREYZ))) \
|| (ENABLED(SCARA) && (ENABLED(COREXY) || ENABLED(COREXZ) || ENABLED(COREYZ))) \
|| (ENABLED(COREXY) && (ENABLED(COREXZ) || ENABLED(COREYZ))) \
|| (ENABLED(COREXZ) && ENABLED(COREYZ))
#error "Please enable only one of DELTA, SCARA, COREXY, COREXZ, or COREYZ."
#define COUNT_KIN_1 0
#if ENABLED(DELTA)
#define COUNT_KIN_2 INCREMENT(COUNT_KIN_1)
#else
#define COUNT_KIN_2 COUNT_KIN_1
#endif
#if ENABLED(MORGAN_SCARA)
#define COUNT_KIN_3 INCREMENT(COUNT_KIN_2)
#else
#define COUNT_KIN_3 COUNT_KIN_2
#endif
#if ENABLED(MAKERARM_SCARA)
#define COUNT_KIN_4 INCREMENT(COUNT_KIN_3)
#else
#define COUNT_KIN_4 COUNT_KIN_3
#endif
#if ENABLED(COREXY)
#define COUNT_KIN_5 INCREMENT(COUNT_KIN_4)
#else
#define COUNT_KIN_5 COUNT_KIN_4
#endif
#if ENABLED(COREXZ)
#define COUNT_KIN_6 INCREMENT(COUNT_KIN_5)
#else
#define COUNT_KIN_6 COUNT_KIN_5
#endif
#if ENABLED(COREYZ)
#define COUNT_KIN_7 INCREMENT(COUNT_KIN_6)
#else
#define COUNT_KIN_7 COUNT_KIN_6
#endif
#if COUNT_KIN_7 > 1
#error "Please enable only one of DELTA, MORGAN_SCARA, MAKERARM_SCARA, COREXY, COREXZ, or COREYZ."
#endif
/**
@ -750,7 +778,7 @@
#elif ENABLED(DELTA)
#error "Z_DUAL_ENDSTOPS is not compatible with DELTA."
#endif
#elif DISABLED(SCARA)
#elif !IS_SCARA
#if X_HOME_DIR < 0 && DISABLED(USE_XMIN_PLUG)
#error "Enable USE_XMIN_PLUG when homing X to MIN."
#elif X_HOME_DIR > 0 && DISABLED(USE_XMAX_PLUG)
@ -783,3 +811,136 @@
#error "I2C_SLAVE_ADDRESS can't be over 127. (Only 7 bits allowed.)"
#endif
#endif
/**
* Make sure only one display is enabled
*
* Note: BQ_LCD_SMART_CONTROLLER => REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
* REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER => REPRAP_DISCOUNT_SMART_CONTROLLER
* SAV_3DGLCD => U8GLIB_SH1106 => ULTIMAKERCONTROLLER
* miniVIKI => ULTIMAKERCONTROLLER
* VIKI2 => ULTIMAKERCONTROLLER
* ELB_FULL_GRAPHIC_CONTROLLER => ULTIMAKERCONTROLLER
* PANEL_ONE => ULTIMAKERCONTROLLER
*/
#define COUNT_LCD_1 0
#if ENABLED(ULTIMAKERCONTROLLER) \
&& DISABLED(SAV_3DGLCD) && DISABLED(miniVIKI) && DISABLED(VIKI2) \
&& DISABLED(ELB_FULL_GRAPHIC_CONTROLLER) && DISABLED(PANEL_ONE)
#define COUNT_LCD_2 INCREMENT(COUNT_LCD_1)
#else
#define COUNT_LCD_2 COUNT_LCD_1
#endif
#if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER) && DISABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
#define COUNT_LCD_3 INCREMENT(COUNT_LCD_2)
#else
#define COUNT_LCD_3 COUNT_LCD_2
#endif
#if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) && DISABLED(BQ_LCD_SMART_CONTROLLER)
#define COUNT_LCD_4 INCREMENT(COUNT_LCD_3)
#else
#define COUNT_LCD_4 COUNT_LCD_3
#endif
#if ENABLED(CARTESIO_UI)
#define COUNT_LCD_5 INCREMENT(COUNT_LCD_4)
#else
#define COUNT_LCD_5 COUNT_LCD_4
#endif
#if ENABLED(PANEL_ONE)
#define COUNT_LCD_6 INCREMENT(COUNT_LCD_5)
#else
#define COUNT_LCD_6 COUNT_LCD_5
#endif
#if ENABLED(MAKRPANEL)
#define COUNT_LCD_7 INCREMENT(COUNT_LCD_6)
#else
#define COUNT_LCD_7 COUNT_LCD_6
#endif
#if ENABLED(REPRAPWORLD_GRAPHICAL_LCD)
#define COUNT_LCD_8 INCREMENT(COUNT_LCD_7)
#else
#define COUNT_LCD_8 COUNT_LCD_7
#endif
#if ENABLED(VIKI2)
#define COUNT_LCD_9 INCREMENT(COUNT_LCD_8)
#else
#define COUNT_LCD_9 COUNT_LCD_8
#endif
#if ENABLED(miniVIKI)
#define COUNT_LCD_10 INCREMENT(COUNT_LCD_9)
#else
#define COUNT_LCD_10 COUNT_LCD_9
#endif
#if ENABLED(ELB_FULL_GRAPHIC_CONTROLLER)
#define COUNT_LCD_11 INCREMENT(COUNT_LCD_10)
#else
#define COUNT_LCD_11 COUNT_LCD_10
#endif
#if ENABLED(G3D_PANEL)
#define COUNT_LCD_12 INCREMENT(COUNT_LCD_11)
#else
#define COUNT_LCD_12 COUNT_LCD_11
#endif
#if ENABLED(MINIPANEL)
#define COUNT_LCD_13 INCREMENT(COUNT_LCD_12)
#else
#define COUNT_LCD_13 COUNT_LCD_12
#endif
#if ENABLED(REPRAPWORLD_KEYPAD)
#define COUNT_LCD_14 INCREMENT(COUNT_LCD_13)
#else
#define COUNT_LCD_14 COUNT_LCD_13
#endif
#if ENABLED(RIGIDBOT_PANEL)
#define COUNT_LCD_15 INCREMENT(COUNT_LCD_14)
#else
#define COUNT_LCD_15 COUNT_LCD_14
#endif
#if ENABLED(RA_CONTROL_PANEL)
#define COUNT_LCD_16 INCREMENT(COUNT_LCD_15)
#else
#define COUNT_LCD_16 COUNT_LCD_15
#endif
#if ENABLED(LCD_I2C_SAINSMART_YWROBOT)
#define COUNT_LCD_17 INCREMENT(COUNT_LCD_16)
#else
#define COUNT_LCD_17 COUNT_LCD_16
#endif
#if ENABLED(LCM1602)
#define COUNT_LCD_18 INCREMENT(COUNT_LCD_17)
#else
#define COUNT_LCD_18 COUNT_LCD_17
#endif
#if ENABLED(LCD_I2C_PANELOLU2)
#define COUNT_LCD_19 INCREMENT(COUNT_LCD_18)
#else
#define COUNT_LCD_19 COUNT_LCD_18
#endif
#if ENABLED(LCD_I2C_VIKI)
#define COUNT_LCD_20 INCREMENT(COUNT_LCD_19)
#else
#define COUNT_LCD_20 COUNT_LCD_19
#endif
#if ENABLED(U8GLIB_SSD1306)
#define COUNT_LCD_21 INCREMENT(COUNT_LCD_20)
#else
#define COUNT_LCD_21 COUNT_LCD_20
#endif
#if ENABLED(SAV_3DLCD)
#define COUNT_LCD_22 INCREMENT(COUNT_LCD_21)
#else
#define COUNT_LCD_22 COUNT_LCD_21
#endif
#if ENABLED(BQ_LCD_SMART_CONTROLLER)
#define COUNT_LCD_23 INCREMENT(COUNT_LCD_22)
#else
#define COUNT_LCD_23 COUNT_LCD_22
#endif
#if ENABLED(SAV_3DGLCD)
#define COUNT_LCD_24 INCREMENT(COUNT_LCD_23)
#else
#define COUNT_LCD_24 COUNT_LCD_23
#endif
#if COUNT_LCD_24 > 1
#error "Please select no more than one LCD controller option."
#endif

8
Marlin/configuration_store.cpp
View file

@ -330,7 +330,7 @@ void Config_StoreSettings() {
#endif
EEPROM_WRITE(lcd_contrast);
#if ENABLED(SCARA)
#if IS_SCARA
EEPROM_WRITE(axis_scaling); // 3 floats
#else
dummy = 1.0f;
@ -520,7 +520,7 @@ void Config_RetrieveSettings() {
#endif
EEPROM_READ(lcd_contrast);
#if ENABLED(SCARA)
#if IS_SCARA
EEPROM_READ(axis_scaling); // 3 floats
#else
EEPROM_READ(dummy);
@ -584,7 +584,7 @@ void Config_ResetDefault() {
planner.axis_steps_per_mm[i] = tmp1[i];
planner.max_feedrate_mm_s[i] = tmp2[i];
planner.max_acceleration_mm_per_s2[i] = tmp3[i];
#if ENABLED(SCARA)
#if IS_SCARA
if (i < COUNT(axis_scaling))
axis_scaling[i] = 1;
#endif
@ -716,7 +716,7 @@ void Config_PrintSettings(bool forReplay) {
CONFIG_ECHO_START;
#if ENABLED(SCARA)
#if IS_SCARA
if (!forReplay) {
SERIAL_ECHOLNPGM("Scaling factors:");
CONFIG_ECHO_START;

3
Marlin/enum.h
View file

@ -42,7 +42,8 @@ enum AxisEnum {
E_AXIS = 3,
X_HEAD = 4,
Y_HEAD = 5,
Z_HEAD = 6
Z_HEAD = 6,
ALL_AXES = 100
};
#define LOOP_XYZ(VAR) for (uint8_t VAR=X_AXIS; VAR<=Z_AXIS; VAR++)

16
Marlin/example_configurations/Cartesio/Configuration_adv.h
View file

@ -168,14 +168,16 @@
// @section extruder
// extruder run-out prevention.
//if the machine is idle, and the temperature over MINTEMP, every couple of SECONDS some filament is extruded
// Extruder runout prevention.
// If the machine is idle and the temperature over MINTEMP
// then extrude some filament every couple of SECONDS.
//#define EXTRUDER_RUNOUT_PREVENT
#define EXTRUDER_RUNOUT_MINTEMP 190
#define EXTRUDER_RUNOUT_SECONDS 30
#define EXTRUDER_RUNOUT_ESTEPS 14 // mm filament
#define EXTRUDER_RUNOUT_SPEED 1500 // extrusion speed
#define EXTRUDER_RUNOUT_EXTRUDE 100
#if ENABLED(EXTRUDER_RUNOUT_PREVENT)
#define EXTRUDER_RUNOUT_MINTEMP 190
#define EXTRUDER_RUNOUT_SECONDS 30
#define EXTRUDER_RUNOUT_SPEED 1500 // mm/m
#define EXTRUDER_RUNOUT_EXTRUDE 5 // mm
#endif
// @section temperature

16
Marlin/example_configurations/Felix/Configuration_adv.h
View file

@ -168,14 +168,16 @@
// @section extruder
// extruder run-out prevention.
//if the machine is idle, and the temperature over MINTEMP, every couple of SECONDS some filament is extruded
// Extruder runout prevention.
// If the machine is idle and the temperature over MINTEMP
// then extrude some filament every couple of SECONDS.
//#define EXTRUDER_RUNOUT_PREVENT
#define EXTRUDER_RUNOUT_MINTEMP 190
#define EXTRUDER_RUNOUT_SECONDS 30
#define EXTRUDER_RUNOUT_ESTEPS 14 // mm filament
#define EXTRUDER_RUNOUT_SPEED 1500 // extrusion speed
#define EXTRUDER_RUNOUT_EXTRUDE 100
#if ENABLED(EXTRUDER_RUNOUT_PREVENT)
#define EXTRUDER_RUNOUT_MINTEMP 190
#define EXTRUDER_RUNOUT_SECONDS 30
#define EXTRUDER_RUNOUT_SPEED 1500 // mm/m
#define EXTRUDER_RUNOUT_EXTRUDE 5 // mm
#endif
// @section temperature

16
Marlin/example_configurations/Hephestos/Configuration_adv.h
View file

@ -168,14 +168,16 @@
// @section extruder
// extruder run-out prevention.
//if the machine is idle, and the temperature over MINTEMP, every couple of SECONDS some filament is extruded
// Extruder runout prevention.
// If the machine is idle and the temperature over MINTEMP
// then extrude some filament every couple of SECONDS.
//#define EXTRUDER_RUNOUT_PREVENT
#define EXTRUDER_RUNOUT_MINTEMP 190
#define EXTRUDER_RUNOUT_SECONDS 30
#define EXTRUDER_RUNOUT_ESTEPS 14 // mm filament
#define EXTRUDER_RUNOUT_SPEED 1500 // extrusion speed
#define EXTRUDER_RUNOUT_EXTRUDE 100
#if ENABLED(EXTRUDER_RUNOUT_PREVENT)
#define EXTRUDER_RUNOUT_MINTEMP 190
#define EXTRUDER_RUNOUT_SECONDS 30
#define EXTRUDER_RUNOUT_SPEED 1500 // mm/m
#define EXTRUDER_RUNOUT_EXTRUDE 5 // mm
#endif
// @section temperature

16
Marlin/example_configurations/Hephestos_2/Configuration_adv.h
View file

@ -168,14 +168,16 @@
// @section extruder
// extruder run-out prevention.
//if the machine is idle, and the temperature over MINTEMP, every couple of SECONDS some filament is extruded
// Extruder runout prevention.
// If the machine is idle and the temperature over MINTEMP
// then extrude some filament every couple of SECONDS.
//#define EXTRUDER_RUNOUT_PREVENT
#define EXTRUDER_RUNOUT_MINTEMP 190
#define EXTRUDER_RUNOUT_SECONDS 30
#define EXTRUDER_RUNOUT_ESTEPS 14 // mm filament
#define EXTRUDER_RUNOUT_SPEED 1500 // extrusion speed
#define EXTRUDER_RUNOUT_EXTRUDE 100
#if ENABLED(EXTRUDER_RUNOUT_PREVENT)
#define EXTRUDER_RUNOUT_MINTEMP 190
#define EXTRUDER_RUNOUT_SECONDS 30
#define EXTRUDER_RUNOUT_SPEED 1500 // mm/m
#define EXTRUDER_RUNOUT_EXTRUDE 5 // mm
#endif
// @section temperature

16
Marlin/example_configurations/K8200/Configuration_adv.h
View file

@ -174,14 +174,16 @@
// @section extruder
// extruder run-out prevention.
//if the machine is idle, and the temperature over MINTEMP, every couple of SECONDS some filament is extruded
// Extruder runout prevention.
// If the machine is idle and the temperature over MINTEMP
// then extrude some filament every couple of SECONDS.
//#define EXTRUDER_RUNOUT_PREVENT
#define EXTRUDER_RUNOUT_MINTEMP 190
#define EXTRUDER_RUNOUT_SECONDS 30
#define EXTRUDER_RUNOUT_ESTEPS 14 // mm filament
#define EXTRUDER_RUNOUT_SPEED 1500 // extrusion speed
#define EXTRUDER_RUNOUT_EXTRUDE 100
#if ENABLED(EXTRUDER_RUNOUT_PREVENT)
#define EXTRUDER_RUNOUT_MINTEMP 190
#define EXTRUDER_RUNOUT_SECONDS 30
#define EXTRUDER_RUNOUT_SPEED 1500 // mm/m
#define EXTRUDER_RUNOUT_EXTRUDE 5 // mm
#endif
// @section temperature

16
Marlin/example_configurations/K8400/Configuration_adv.h
View file

@ -168,14 +168,16 @@
// @section extruder
// extruder run-out prevention.
//if the machine is idle, and the temperature over MINTEMP, every couple of SECONDS some filament is extruded
// Extruder runout prevention.
// If the machine is idle and the temperature over MINTEMP
// then extrude some filament every couple of SECONDS.
//#define EXTRUDER_RUNOUT_PREVENT
#define EXTRUDER_RUNOUT_MINTEMP 190
#define EXTRUDER_RUNOUT_SECONDS 30
#define EXTRUDER_RUNOUT_ESTEPS 14 // mm filament
#define EXTRUDER_RUNOUT_SPEED 1500 // extrusion speed
#define EXTRUDER_RUNOUT_EXTRUDE 100
#if ENABLED(EXTRUDER_RUNOUT_PREVENT)
#define EXTRUDER_RUNOUT_MINTEMP 190
#define EXTRUDER_RUNOUT_SECONDS 30
#define EXTRUDER_RUNOUT_SPEED 1500 // mm/m
#define EXTRUDER_RUNOUT_EXTRUDE 5 // mm
#endif
// @section temperature

16
Marlin/example_configurations/RigidBot/Configuration_adv.h
View file

@ -168,14 +168,16 @@
// @section extruder
// extruder run-out prevention.
//if the machine is idle, and the temperature over MINTEMP, every couple of SECONDS some filament is extruded
// Extruder runout prevention.
// If the machine is idle and the temperature over MINTEMP
// then extrude some filament every couple of SECONDS.
//#define EXTRUDER_RUNOUT_PREVENT
#define EXTRUDER_RUNOUT_MINTEMP 190
#define EXTRUDER_RUNOUT_SECONDS 30
#define EXTRUDER_RUNOUT_ESTEPS 14 // mm filament
#define EXTRUDER_RUNOUT_SPEED 1500 // extrusion speed
#define EXTRUDER_RUNOUT_EXTRUDE 100
#if ENABLED(EXTRUDER_RUNOUT_PREVENT)
#define EXTRUDER_RUNOUT_MINTEMP 190
#define EXTRUDER_RUNOUT_SECONDS 30
#define EXTRUDER_RUNOUT_SPEED 1500 // mm/m
#define EXTRUDER_RUNOUT_EXTRUDE 5 // mm
#endif
// @section temperature

42
Marlin/example_configurations/SCARA/Configuration.h
View file

@ -75,35 +75,37 @@
//
//===========================================================================
//========================= SCARA Settings ==================================
//============================= SCARA Printer ===============================
//===========================================================================
// SCARA-mode for Marlin has been developed by QHARLEY in ZA in 2012/2013. Implemented
// MORGAN_SCARA for Marlin was developed by QHARLEY in ZA in 2012/2013. Implemented
// and slightly reworked by JCERNY in 06/2014 with the goal to bring it into Master-Branch
// QHARLEYS Autobedlevelling has not been ported, because Marlin has now Bed-levelling
// You might need Z-Min endstop on SCARA-Printer to use this feature. Actually untested!
// Uncomment to use Morgan scara mode
#define SCARA
#define SCARA_SEGMENTS_PER_SECOND 200 // If movement is choppy try lowering this value
// Length of inner support arm
#define Linkage_1 150 //mm Preprocessor cannot handle decimal point...
// Length of outer support arm Measure arm lengths precisely and enter
#define Linkage_2 150 //mm
// SCARA tower offset (position of Tower relative to bed zero position)
// This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
#define SCARA_offset_x 100 //mm
#define SCARA_offset_y -56 //mm
#define SCARA_RAD2DEG 57.2957795 // to convert RAD to degrees
// Specify the specific SCARA model
#define MORGAN_SCARA
//#define MAKERARM_SCARA
#define THETA_HOMING_OFFSET 0 //calculatated from Calibration Guide and command M360 / M114 see picture in http://reprap.harleystudio.co.za/?page_id=1073
#define PSI_HOMING_OFFSET 0 //calculatated from Calibration Guide and command M364 / M114 see picture in http://reprap.harleystudio.co.za/?page_id=1073
#if ENABLED(MORGAN_SCARA) || ENABLED(MAKERARM_SCARA)
//#define DEBUG_SCARA_KINEMATICS
//some helper variables to make kinematics faster
#define L1_2 sq(Linkage_1) // do not change
#define L2_2 sq(Linkage_2) // do not change
#define SCARA_SEGMENTS_PER_SECOND 200 // If movement is choppy try lowering this value
// Length of inner support arm
#define SCARA_LINKAGE_1 150 //mm Preprocessor cannot handle decimal point...
// Length of outer support arm Measure arm lengths precisely and enter
#define SCARA_LINKAGE_2 150 //mm
// SCARA tower offset (position of Tower relative to bed zero position)
// This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
#define SCARA_OFFSET_X 100 //mm
#define SCARA_OFFSET_Y -56 //mm
#define THETA_HOMING_OFFSET 0 //calculatated from Calibration Guide and command M360 / M114 see picture in http://reprap.harleystudio.co.za/?page_id=1073
#define PSI_HOMING_OFFSET 0 //calculatated from Calibration Guide and command M364 / M114 see picture in http://reprap.harleystudio.co.za/?page_id=1073
#endif
//===========================================================================
//========================= SCARA Settings end ==============================
//==================== END ==== SCARA Printer ==== END ======================
//===========================================================================
// @section info

16
Marlin/example_configurations/SCARA/Configuration_adv.h
View file

@ -168,14 +168,16 @@
// @section extruder
// extruder run-out prevention.
//if the machine is idle, and the temperature over MINTEMP, every couple of SECONDS some filament is extruded
// Extruder runout prevention.
// If the machine is idle and the temperature over MINTEMP
// then extrude some filament every couple of SECONDS.
//#define EXTRUDER_RUNOUT_PREVENT
#define EXTRUDER_RUNOUT_MINTEMP 180
#define EXTRUDER_RUNOUT_SECONDS 30
#define EXTRUDER_RUNOUT_ESTEPS 14 // mm filament
#define EXTRUDER_RUNOUT_SPEED 180 // extrusion speed
#define EXTRUDER_RUNOUT_EXTRUDE 100
#if ENABLED(EXTRUDER_RUNOUT_PREVENT)
#define EXTRUDER_RUNOUT_MINTEMP 190
#define EXTRUDER_RUNOUT_SECONDS 30
#define EXTRUDER_RUNOUT_SPEED 180 // mm/m
#define EXTRUDER_RUNOUT_EXTRUDE 5 // mm
#endif
// @section temperature

16
Marlin/example_configurations/TAZ4/Configuration_adv.h
View file

@ -168,14 +168,16 @@
// @section extruder
// extruder run-out prevention.
//if the machine is idle, and the temperature over MINTEMP, every couple of SECONDS some filament is extruded
// Extruder runout prevention.
// If the machine is idle and the temperature over MINTEMP
// then extrude some filament every couple of SECONDS.
//#define EXTRUDER_RUNOUT_PREVENT
#define EXTRUDER_RUNOUT_MINTEMP 190
#define EXTRUDER_RUNOUT_SECONDS 30
#define EXTRUDER_RUNOUT_ESTEPS 14 // mm filament
#define EXTRUDER_RUNOUT_SPEED 1500 // extrusion speed
#define EXTRUDER_RUNOUT_EXTRUDE 100
#if ENABLED(EXTRUDER_RUNOUT_PREVENT)
#define EXTRUDER_RUNOUT_MINTEMP 190
#define EXTRUDER_RUNOUT_SECONDS 30
#define EXTRUDER_RUNOUT_SPEED 1500 // mm/m
#define EXTRUDER_RUNOUT_EXTRUDE 5 // mm
#endif
// @section temperature

16
Marlin/example_configurations/WITBOX/Configuration_adv.h
View file

@ -168,14 +168,16 @@
// @section extruder
// extruder run-out prevention.
//if the machine is idle, and the temperature over MINTEMP, every couple of SECONDS some filament is extruded
// Extruder runout prevention.
// If the machine is idle and the temperature over MINTEMP
// then extrude some filament every couple of SECONDS.
//#define EXTRUDER_RUNOUT_PREVENT
#define EXTRUDER_RUNOUT_MINTEMP 190
#define EXTRUDER_RUNOUT_SECONDS 30
#define EXTRUDER_RUNOUT_ESTEPS 14 // mm filament
#define EXTRUDER_RUNOUT_SPEED 1500 // extrusion speed
#define EXTRUDER_RUNOUT_EXTRUDE 100
#if ENABLED(EXTRUDER_RUNOUT_PREVENT)
#define EXTRUDER_RUNOUT_MINTEMP 190
#define EXTRUDER_RUNOUT_SECONDS 30
#define EXTRUDER_RUNOUT_SPEED 1500 // mm/m
#define EXTRUDER_RUNOUT_EXTRUDE 5 // mm
#endif
// @section temperature

16
Marlin/example_configurations/delta/biv2.5/Configuration_adv.h
View file

@ -168,14 +168,16 @@
// @section extruder
// extruder run-out prevention.
//if the machine is idle, and the temperature over MINTEMP, every couple of SECONDS some filament is extruded
// Extruder runout prevention.
// If the machine is idle and the temperature over MINTEMP
// then extrude some filament every couple of SECONDS.
//#define EXTRUDER_RUNOUT_PREVENT
#define EXTRUDER_RUNOUT_MINTEMP 190
#define EXTRUDER_RUNOUT_SECONDS 30
#define EXTRUDER_RUNOUT_ESTEPS 14 // mm filament
#define EXTRUDER_RUNOUT_SPEED 1500 // extrusion speed
#define EXTRUDER_RUNOUT_EXTRUDE 100
#if ENABLED(EXTRUDER_RUNOUT_PREVENT)
#define EXTRUDER_RUNOUT_MINTEMP 190
#define EXTRUDER_RUNOUT_SECONDS 30
#define EXTRUDER_RUNOUT_SPEED 1500 // mm/m
#define EXTRUDER_RUNOUT_EXTRUDE 5 // mm
#endif
// @section temperature

16
Marlin/example_configurations/delta/generic/Configuration_adv.h
View file

@ -168,14 +168,16 @@
// @section extruder
// extruder run-out prevention.
//if the machine is idle, and the temperature over MINTEMP, every couple of SECONDS some filament is extruded
// Extruder runout prevention.
// If the machine is idle and the temperature over MINTEMP
// then extrude some filament every couple of SECONDS.
//#define EXTRUDER_RUNOUT_PREVENT
#define EXTRUDER_RUNOUT_MINTEMP 190
#define EXTRUDER_RUNOUT_SECONDS 30
#define EXTRUDER_RUNOUT_ESTEPS 14 // mm filament
#define EXTRUDER_RUNOUT_SPEED 1500 // extrusion speed
#define EXTRUDER_RUNOUT_EXTRUDE 100
#if ENABLED(EXTRUDER_RUNOUT_PREVENT)
#define EXTRUDER_RUNOUT_MINTEMP 190
#define EXTRUDER_RUNOUT_SECONDS 30
#define EXTRUDER_RUNOUT_SPEED 1500 // mm/m
#define EXTRUDER_RUNOUT_EXTRUDE 5 // mm
#endif
// @section temperature

16
Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h
View file

@ -168,14 +168,16 @@
// @section extruder
// extruder run-out prevention.
//if the machine is idle, and the temperature over MINTEMP, every couple of SECONDS some filament is extruded
// Extruder runout prevention.
// If the machine is idle and the temperature over MINTEMP
// then extrude some filament every couple of SECONDS.
//#define EXTRUDER_RUNOUT_PREVENT
#define EXTRUDER_RUNOUT_MINTEMP 190
#define EXTRUDER_RUNOUT_SECONDS 30
#define EXTRUDER_RUNOUT_ESTEPS 14 // mm filament
#define EXTRUDER_RUNOUT_SPEED 1500 // extrusion speed
#define EXTRUDER_RUNOUT_EXTRUDE 100
#if ENABLED(EXTRUDER_RUNOUT_PREVENT)
#define EXTRUDER_RUNOUT_MINTEMP 190
#define EXTRUDER_RUNOUT_SECONDS 30
#define EXTRUDER_RUNOUT_SPEED 1500 // mm/m
#define EXTRUDER_RUNOUT_EXTRUDE 5 // mm
#endif
// @section temperature

16
Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h
View file

@ -173,14 +173,16 @@
// @section extruder
// extruder run-out prevention.
//if the machine is idle, and the temperature over MINTEMP, every couple of SECONDS some filament is extruded
// Extruder runout prevention.
// If the machine is idle and the temperature over MINTEMP
// then extrude some filament every couple of SECONDS.
//#define EXTRUDER_RUNOUT_PREVENT
#define EXTRUDER_RUNOUT_MINTEMP 190
#define EXTRUDER_RUNOUT_SECONDS 30
#define EXTRUDER_RUNOUT_ESTEPS 14 // mm filament
#define EXTRUDER_RUNOUT_SPEED 1500 // extrusion speed
#define EXTRUDER_RUNOUT_EXTRUDE 100
#if ENABLED(EXTRUDER_RUNOUT_PREVENT)
#define EXTRUDER_RUNOUT_MINTEMP 190
#define EXTRUDER_RUNOUT_SECONDS 30
#define EXTRUDER_RUNOUT_SPEED 1500 // mm/m
#define EXTRUDER_RUNOUT_EXTRUDE 5 // mm
#endif
// @section temperature

16
Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h
View file

@ -168,14 +168,16 @@
// @section extruder
// extruder run-out prevention.
//if the machine is idle, and the temperature over MINTEMP, every couple of SECONDS some filament is extruded
// Extruder runout prevention.
// If the machine is idle and the temperature over MINTEMP
// then extrude some filament every couple of SECONDS.
//#define EXTRUDER_RUNOUT_PREVENT
#define EXTRUDER_RUNOUT_MINTEMP 190
#define EXTRUDER_RUNOUT_SECONDS 30
#define EXTRUDER_RUNOUT_ESTEPS 14 // mm filament
#define EXTRUDER_RUNOUT_SPEED 1500 // extrusion speed
#define EXTRUDER_RUNOUT_EXTRUDE 100
#if ENABLED(EXTRUDER_RUNOUT_PREVENT)
#define EXTRUDER_RUNOUT_MINTEMP 190
#define EXTRUDER_RUNOUT_SECONDS 30
#define EXTRUDER_RUNOUT_SPEED 1500 // mm/m
#define EXTRUDER_RUNOUT_EXTRUDE 5 // mm
#endif
// @section temperature

16
Marlin/example_configurations/makibox/Configuration_adv.h
View file

@ -168,14 +168,16 @@
// @section extruder
// extruder run-out prevention.
//if the machine is idle, and the temperature over MINTEMP, every couple of SECONDS some filament is extruded
// Extruder runout prevention.
// If the machine is idle and the temperature over MINTEMP
// then extrude some filament every couple of SECONDS.
//#define EXTRUDER_RUNOUT_PREVENT
#define EXTRUDER_RUNOUT_MINTEMP 190
#define EXTRUDER_RUNOUT_SECONDS 30
#define EXTRUDER_RUNOUT_ESTEPS 14 // mm filament
#define EXTRUDER_RUNOUT_SPEED 1500 // extrusion speed
#define EXTRUDER_RUNOUT_EXTRUDE 100
#if ENABLED(EXTRUDER_RUNOUT_PREVENT)
#define EXTRUDER_RUNOUT_MINTEMP 190
#define EXTRUDER_RUNOUT_SECONDS 30
#define EXTRUDER_RUNOUT_SPEED 1500 // mm/m
#define EXTRUDER_RUNOUT_EXTRUDE 5 // mm
#endif
// @section temperature

16
Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h
View file

@ -168,14 +168,16 @@
// @section extruder
// extruder run-out prevention.
//if the machine is idle, and the temperature over MINTEMP, every couple of SECONDS some filament is extruded
// Extruder runout prevention.
// If the machine is idle and the temperature over MINTEMP
// then extrude some filament every couple of SECONDS.
//#define EXTRUDER_RUNOUT_PREVENT
#define EXTRUDER_RUNOUT_MINTEMP 190
#define EXTRUDER_RUNOUT_SECONDS 30
#define EXTRUDER_RUNOUT_ESTEPS 14 // mm filament
#define EXTRUDER_RUNOUT_SPEED 1500 // extrusion speed
#define EXTRUDER_RUNOUT_EXTRUDE 100
#if ENABLED(EXTRUDER_RUNOUT_PREVENT)
#define EXTRUDER_RUNOUT_MINTEMP 190
#define EXTRUDER_RUNOUT_SECONDS 30
#define EXTRUDER_RUNOUT_SPEED 1500 // mm/m
#define EXTRUDER_RUNOUT_EXTRUDE 5 // mm
#endif
// @section temperature

6
Marlin/language.h
View file

@ -157,9 +157,9 @@
#define MSG_ENDSTOP_OPEN "open"
#define MSG_HOTEND_OFFSET "Hotend offsets:"
#define MSG_DUPLICATION_MODE "Duplication mode: "
#define MSG_SOFT_ENDSTOPS "Soft endstops"
#define MSG_SOFT_MIN "Min"
#define MSG_SOFT_MAX "Max"
#define MSG_SOFT_ENDSTOPS "Soft endstops: "
#define MSG_SOFT_MIN " Min: "
#define MSG_SOFT_MAX " Max: "
#define MSG_SD_CANT_OPEN_SUBDIR "Cannot open subdir "
#define MSG_SD_INIT_FAIL "SD init fail"

3
Marlin/language_en.h
View file

@ -408,6 +408,9 @@
#ifndef MSG_ERR_MINTEMP_BED
#define MSG_ERR_MINTEMP_BED "Err: MINTEMP BED"
#endif
#ifndef MSG_ERR_Z_HOMING
#define MSG_ERR_Z_HOMING "G28 Z Forbidden"
#endif
#ifndef MSG_HALTED
#define MSG_HALTED "PRINTER HALTED"
#endif

7
Marlin/macros.h
View file

@ -55,7 +55,8 @@
#endif
#define RADIANS(d) ((d)*M_PI/180.0)
#define DEGREES(r) ((r)*180.0/M_PI)
#define HYPOT(x,y) sqrt(sq(x)+sq(y))
#define HYPOT2(x,y) (sq(x)+sq(y))
#define HYPOT(x,y) sqrt(HYPOT2(x,y))
// Macros to contrain values
#define NOLESS(v,n) do{ if (v < n) v = n; }while(0)
@ -124,4 +125,8 @@
#define MAX3(a, b, c) max(max(a, b), c)
#define MAX4(a, b, c, d) max(max(max(a, b), c), d)
#define UNEAR_ZERO(x) ((x) < 0.000001)
#define NEAR_ZERO(x) ((x) > -0.000001 && (x) < 0.000001)
#define NEAR(x,y) NEAR_ZERO((x)-(y))
#endif //__MACROS_H

120
Marlin/planner.cpp
View file

@ -98,7 +98,7 @@ float Planner::min_feedrate_mm_s,
Planner::max_e_jerk,
Planner::min_travel_feedrate_mm_s;
#if ENABLED(AUTO_BED_LEVELING_FEATURE)
#if ENABLED(AUTO_BED_LEVELING_LINEAR)
matrix_3x3 Planner::bed_level_matrix; // Transform to compensate for bed level
#endif
@ -138,7 +138,7 @@ void Planner::init() {
memset(position, 0, sizeof(position)); // clear position
LOOP_XYZE(i) previous_speed[i] = 0.0;
previous_nominal_speed = 0.0;
#if ENABLED(AUTO_BED_LEVELING_FEATURE)
#if ENABLED(AUTO_BED_LEVELING_LINEAR)
bed_level_matrix.set_to_identity();
#endif
}
@ -521,37 +521,51 @@ void Planner::check_axes_activity() {
#endif
}
#if ENABLED(AUTO_BED_LEVELING_FEATURE) || ENABLED(MESH_BED_LEVELING)
#if PLANNER_LEVELING
void Planner::apply_leveling(
#if ENABLED(MESH_BED_LEVELING)
const float &x, const float &y
#else
float &x, float &y
#endif
, float &z
) {
void Planner::apply_leveling(float &lx, float &ly, float &lz) {
#if ENABLED(MESH_BED_LEVELING)
if (mbl.active())
z += mbl.get_z(RAW_X_POSITION(x), RAW_Y_POSITION(y));
lz += mbl.get_z(RAW_X_POSITION(lx), RAW_Y_POSITION(ly));
#elif ENABLED(AUTO_BED_LEVELING_FEATURE)
#elif ENABLED(AUTO_BED_LEVELING_LINEAR)
float tx = RAW_X_POSITION(x) - (X_TILT_FULCRUM),
ty = RAW_Y_POSITION(y) - (Y_TILT_FULCRUM),
tz = RAW_Z_POSITION(z);
float dx = RAW_X_POSITION(lx) - (X_TILT_FULCRUM),
dy = RAW_Y_POSITION(ly) - (Y_TILT_FULCRUM),
dz = RAW_Z_POSITION(lz);
apply_rotation_xyz(bed_level_matrix, tx, ty, tz);
apply_rotation_xyz(bed_level_matrix, dx, dy, dz);
x = LOGICAL_X_POSITION(tx + X_TILT_FULCRUM);
y = LOGICAL_Y_POSITION(ty + Y_TILT_FULCRUM);
z = LOGICAL_Z_POSITION(tz);
lx = LOGICAL_X_POSITION(dx + X_TILT_FULCRUM);
ly = LOGICAL_Y_POSITION(dy + Y_TILT_FULCRUM);
lz = LOGICAL_Z_POSITION(dz);
#endif
}
#endif
void Planner::unapply_leveling(float &lx, float &ly, float &lz) {
#if ENABLED(MESH_BED_LEVELING)
if (mbl.active())
lz -= mbl.get_z(RAW_X_POSITION(lx), RAW_Y_POSITION(ly));
#elif ENABLED(AUTO_BED_LEVELING_LINEAR)
matrix_3x3 inverse = matrix_3x3::transpose(bed_level_matrix);
float dx = lx - (X_TILT_FULCRUM), dy = ly - (Y_TILT_FULCRUM), dz = lz;
apply_rotation_xyz(inverse, dx, dy, dz);
lx = LOGICAL_X_POSITION(dx + X_TILT_FULCRUM);
ly = LOGICAL_Y_POSITION(dy + Y_TILT_FULCRUM);
lz = LOGICAL_Z_POSITION(dz);
#endif
}
#endif // PLANNER_LEVELING
/**
* Planner::buffer_line
@ -562,15 +576,7 @@ void Planner::check_axes_activity() {
* fr_mm_s - (target) speed of the move
* extruder - target extruder
*/
void Planner::buffer_line(
#if ENABLED(AUTO_BED_LEVELING_FEATURE) || ENABLED(MESH_BED_LEVELING)
float x, float y, float z
#else
const float& x, const float& y, const float& z
#endif
, const float& e, float fr_mm_s, const uint8_t extruder
) {
void Planner::buffer_line(ARG_X, ARG_Y, ARG_Z, const float &e, float fr_mm_s, const uint8_t extruder) {
// Calculate the buffer head after we push this byte
int next_buffer_head = next_block_index(block_buffer_head);
@ -578,17 +584,17 @@ void Planner::buffer_line(
// Rest here until there is room in the buffer.
while (block_buffer_tail == next_buffer_head) idle();
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_FEATURE)
apply_leveling(x, y, z);
#if PLANNER_LEVELING
apply_leveling(lx, ly, lz);
#endif
// The target position of the tool in absolute steps
// Calculate target position in absolute steps
//this should be done after the wait, because otherwise a M92 code within the gcode disrupts this calculation somehow
long target[NUM_AXIS] = {
lround(x * axis_steps_per_mm[X_AXIS]),
lround(y * axis_steps_per_mm[Y_AXIS]),
lround(z * axis_steps_per_mm[Z_AXIS]),
lround(lx * axis_steps_per_mm[X_AXIS]),
lround(ly * axis_steps_per_mm[Y_AXIS]),
lround(lz * axis_steps_per_mm[Z_AXIS]),
lround(e * axis_steps_per_mm[E_AXIS])
};
@ -598,11 +604,22 @@ void Planner::buffer_line(
/*
SERIAL_ECHO_START;
SERIAL_ECHOPAIR("Planner X:", x);
SERIAL_ECHOPAIR(" (", dx);
SERIAL_ECHOPAIR(") Y:", y);
SERIAL_ECHOPGM("Planner ", x);
#if IS_KINEMATIC
SERIAL_ECHOPAIR("A:", x);
SERIAL_ECHOPAIR(" (", dx);
SERIAL_ECHOPAIR(") B:", y);
#else
SERIAL_ECHOPAIR("X:", x);
SERIAL_ECHOPAIR(" (", dx);
SERIAL_ECHOPAIR(") Y:", y);
#endif
SERIAL_ECHOPAIR(" (", dy);
SERIAL_ECHOPAIR(") Z:", z);
#elif ENABLED(DELTA)
SERIAL_ECHOPAIR(") C:", z);
#else
SERIAL_ECHOPAIR(") Z:", z);
#endif
SERIAL_ECHOPAIR(" (", dz);
SERIAL_ECHOLNPGM(")");
//*/
@ -671,7 +688,7 @@ void Planner::buffer_line(
// For a mixing extruder, get a magnified step_event_count for each
#if ENABLED(MIXING_EXTRUDER)
for (uint8_t i = 0; i < MIXING_STEPPERS; i++)
block->mix_event_count[i] = (mixing_factor[i] < 0.0001) ? 0 : block->step_event_count / mixing_factor[i];
block->mix_event_count[i] = UNEAR_ZERO(mixing_factor[i]) ? 0 : block->step_event_count / mixing_factor[i];
#endif
#if FAN_COUNT > 0
@ -1124,7 +1141,7 @@ void Planner::buffer_line(
block->advance_rate = acc_dist ? advance / (float)acc_dist : 0;
}
/**
SERIAL_ECHO_START;
SERIAL_ECHO_START;
SERIAL_ECHOPGM("advance :");
SERIAL_ECHO(block->advance/256.0);
SERIAL_ECHOPGM("advance rate :");
@ -1152,22 +1169,15 @@ void Planner::buffer_line(
*
* On CORE machines stepper ABC will be translated from the given XYZ.
*/
void Planner::set_position_mm(
#if ENABLED(AUTO_BED_LEVELING_FEATURE) || ENABLED(MESH_BED_LEVELING)
float x, float y, float z
#else
const float& x, const float& y, const float& z
#endif
, const float& e
) {
void Planner::set_position_mm(ARG_X, ARG_Y, ARG_Z, const float &e) {
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_FEATURE)
apply_leveling(x, y, z);
#if PLANNER_LEVELING
apply_leveling(lx, ly, lz);
#endif
long nx = position[X_AXIS] = lround(x * axis_steps_per_mm[X_AXIS]),
ny = position[Y_AXIS] = lround(y * axis_steps_per_mm[Y_AXIS]),
nz = position[Z_AXIS] = lround(z * axis_steps_per_mm[Z_AXIS]),
long nx = position[X_AXIS] = lround(lx * axis_steps_per_mm[X_AXIS]),
ny = position[Y_AXIS] = lround(ly * axis_steps_per_mm[Y_AXIS]),
nz = position[Z_AXIS] = lround(lz * axis_steps_per_mm[Z_AXIS]),
ne = position[E_AXIS] = lround(e * axis_steps_per_mm[E_AXIS]);
stepper.set_position(nx, ny, nz, ne);
previous_nominal_speed = 0.0; // Resets planner junction speeds. Assumes start from rest.
@ -1193,7 +1203,7 @@ void Planner::reset_acceleration_rates() {
// Recalculate position, steps_to_mm if axis_steps_per_mm changes!
void Planner::refresh_positioning() {
LOOP_XYZE(i) steps_to_mm[i] = 1.0 / axis_steps_per_mm[i];
#if ENABLED(DELTA) || ENABLED(SCARA)
#if IS_KINEMATIC
inverse_kinematics(current_position);
set_position_mm(delta[X_AXIS], delta[Y_AXIS], delta[Z_AXIS], current_position[E_AXIS]);
#else

66
Marlin/planner.h
View file

@ -202,39 +202,45 @@ class Planner {
static bool is_full() { return (block_buffer_tail == BLOCK_MOD(block_buffer_head + 1)); }
#if ENABLED(AUTO_BED_LEVELING_FEATURE) || ENABLED(MESH_BED_LEVELING)
#if ENABLED(MESH_BED_LEVELING)
static void apply_leveling(const float &x, const float &y, float &z);
#else
static void apply_leveling(float &x, float &y, float &z);
#endif
/**
* Add a new linear movement to the buffer.
*
* x,y,z,e - target position in mm
* fr_mm_s - (target) speed of the move (mm/s)
* extruder - target extruder
*/
static void buffer_line(float x, float y, float z, const float& e, float fr_mm_s, const uint8_t extruder);
/**
* Set the planner.position and individual stepper positions.
* Used by G92, G28, G29, and other procedures.
*
* Multiplies by axis_steps_per_mm[] and does necessary conversion
* for COREXY / COREXZ / COREYZ to set the corresponding stepper positions.
*
* Clears previous speed values.
*/
static void set_position_mm(float x, float y, float z, const float& e);
#define ARG_X float lx
#define ARG_Y float ly
#define ARG_Z float lz
#else
#define ARG_X const float &lx
#define ARG_Y const float &ly
#define ARG_Z const float &lz
#endif
static void buffer_line(const float& x, const float& y, const float& z, const float& e, float fr_mm_s, const uint8_t extruder);
static void set_position_mm(const float& x, const float& y, const float& z, const float& e);
#if PLANNER_LEVELING
#endif // AUTO_BED_LEVELING_FEATURE || MESH_BED_LEVELING
/**
* Apply leveling to transform a cartesian position
* as it will be given to the planner and steppers.
*/
static void apply_leveling(float &lx, float &ly, float &lz);
static void unapply_leveling(float &lx, float &ly, float &lz);
#endif
/**
* Add a new linear movement to the buffer.
*
* x,y,z,e - target position in mm
* fr_mm_s - (target) speed of the move (mm/s)
* extruder - target extruder
*/
static void buffer_line(ARG_X, ARG_Y, ARG_Z, const float& e, float fr_mm_s, const uint8_t extruder);
/**
* Set the planner.position and individual stepper positions.
* Used by G92, G28, G29, and other procedures.
*
* Multiplies by axis_steps_per_mm[] and does necessary conversion
* for COREXY / COREXZ / COREYZ to set the corresponding stepper positions.
*
* Clears previous speed values.
*/
static void set_position_mm(ARG_X, ARG_Y, ARG_Z, const float& e);
/**
* Set the E position (mm) of the planner (and the E stepper)

2
Marlin/planner_bezier.cpp
View file

@ -188,7 +188,7 @@ void cubic_b_spline(const float position[NUM_AXIS], const float target[NUM_AXIS]
bez_target[E_AXIS] = interp(position[E_AXIS], target[E_AXIS], t);
clamp_to_software_endstops(bez_target);
#if ENABLED(DELTA) || ENABLED(SCARA)
#if IS_KINEMATIC
inverse_kinematics(bez_target);
#if ENABLED(DELTA) && ENABLED(AUTO_BED_LEVELING_FEATURE)
adjust_delta(bez_target);

2
Marlin/qr_solve.cpp
View file

@ -22,7 +22,7 @@
#include "qr_solve.h"
#if ENABLED(AUTO_BED_LEVELING_GRID)
#if ENABLED(AUTO_BED_LEVELING_LINEAR)
#include <stdlib.h>
#include <math.h>

17
Marlin/stepper.h
View file

@ -91,6 +91,11 @@ class Stepper {
static bool performing_homing;
#endif
//
// Positions of stepper motors, in step units
//
static volatile long count_position[NUM_AXIS];
private:
static unsigned char last_direction_bits; // The next stepping-bits to be output
@ -138,11 +143,6 @@ class Stepper {
static constexpr int motor_current_setting[3] = PWM_MOTOR_CURRENT;
#endif
//
// Positions of stepper motors, in step units
//
static volatile long count_position[NUM_AXIS];
//
// Current direction of stepper motors (+1 or -1)
//
@ -211,6 +211,13 @@ class Stepper {
//
static float get_axis_position_mm(AxisEnum axis);
//
// SCARA AB axes are in degrees, not mm
//
#if IS_SCARA
static FORCE_INLINE float get_axis_position_degrees(AxisEnum axis) { return get_axis_position_mm(axis); }
#endif
//
// The stepper subsystem goes to sleep when it runs out of things to execute. Call this
// to notify the subsystem that it is time to go to work.

4
Marlin/ultralcd.cpp
View file

@ -1418,7 +1418,7 @@ void kill_screen(const char* lcd_msg) {
*
*/
#if ENABLED(DELTA) || ENABLED(SCARA)
#if IS_KINEMATIC
#define _MOVE_XYZ_ALLOWED (axis_homed[X_AXIS] && axis_homed[Y_AXIS] && axis_homed[Z_AXIS])
#else
#define _MOVE_XYZ_ALLOWED true
@ -1823,7 +1823,7 @@ void kill_screen(const char* lcd_msg) {
#if ENABLED(ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED)
MENU_ITEM_EDIT(bool, MSG_ENDSTOP_ABORT, &stepper.abort_on_endstop_hit);
#endif
#if ENABLED(SCARA)
#if IS_SCARA
MENU_ITEM_EDIT(float74, MSG_XSCALE, &axis_scaling[X_AXIS], 0.5, 2);
MENU_ITEM_EDIT(float74, MSG_YSCALE, &axis_scaling[Y_AXIS], 0.5, 2);
#endif