diff --git a/Marlin/boards.h b/Marlin/boards.h
index ae03bdec78..07ee68a330 100644
--- a/Marlin/boards.h
+++ b/Marlin/boards.h
@@ -60,7 +60,8 @@
 #define BOARD_ULTIMAKER_OLD     71   // Ultimaker (Older electronics. Pre 1.5.4. This is rare)
 #define BOARD_ULTIMAIN_2        72   // Ultimainboard 2.x (Uses TEMP_SENSOR 20)
 #define BOARD_3DRAG             77   // 3Drag Controller
-#define BOARD_K8200             78   // Vellemann K8200 Controller (derived from 3Drag Controller)
+#define BOARD_K8200             78   // Velleman K8200 Controller (derived from 3Drag Controller)
+#define BOARD_K8400             79   // Velleman K8400 Controller (derived from 3Drag Controller)
 #define BOARD_TEENSYLU          8    // Teensylu
 #define BOARD_RUMBA             80   // Rumba
 #define BOARD_PRINTRBOARD       81   // Printrboard (AT90USB1286)
diff --git a/Marlin/example_configurations/K8400/Configuration.h b/Marlin/example_configurations/K8400/Configuration.h
new file mode 100644
index 0000000000..a7c61de56b
--- /dev/null
+++ b/Marlin/example_configurations/K8400/Configuration.h
@@ -0,0 +1,1216 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Configuration.h
+ *
+ * Basic settings such as:
+ *
+ * - Type of electronics
+ * - Type of temperature sensor
+ * - Printer geometry
+ * - Endstop configuration
+ * - LCD controller
+ * - Extra features
+ *
+ * Advanced settings can be found in Configuration_adv.h
+ *
+ */
+#ifndef CONFIGURATION_H
+#define CONFIGURATION_H
+
+/**
+ *
+ *  ***********************************
+ *  **  ATTENTION TO ALL DEVELOPERS  **
+ *  ***********************************
+ *
+ * You must increment this version number for every significant change such as,
+ * but not limited to: ADD, DELETE RENAME OR REPURPOSE any directive/option.
+ *
+ * Note: Update also Version.h !
+ */
+#define CONFIGURATION_H_VERSION 010100
+
+#include "boards.h"
+#include "macros.h"
+
+//===========================================================================
+//============================= Getting Started =============================
+//===========================================================================
+
+/**
+ * Here are some standard links for getting your machine calibrated:
+ *
+ * http://reprap.org/wiki/Calibration
+ * http://youtu.be/wAL9d7FgInk
+ * http://calculator.josefprusa.cz
+ * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
+ * http://www.thingiverse.com/thing:5573
+ * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
+ * http://www.thingiverse.com/thing:298812
+ */
+
+//===========================================================================
+//============================= DELTA Printer ===============================
+//===========================================================================
+// For a Delta printer replace the configuration files with the files in the
+// example_configurations/delta directory.
+//
+
+//===========================================================================
+//============================= SCARA Printer ===============================
+//===========================================================================
+// For a Scara printer replace the configuration files with the files in the
+// example_configurations/SCARA directory.
+//
+
+// @section info
+
+#if ENABLED(USE_AUTOMATIC_VERSIONING)
+  #include "_Version.h"
+#else
+  #include "Version.h"
+#endif
+
+// User-specified version info of this build to display in [Pronterface, etc] terminal window during
+// startup. Implementation of an idea by Prof Braino to inform user that any changes made to this
+// build by the user have been successfully uploaded into firmware.
+#define STRING_CONFIG_H_AUTHOR "(Anthony Birkett, default config)" // Who made the changes.
+#define SHOW_BOOTSCREEN
+#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1
+//#define STRING_SPLASH_LINE2 STRING_DISTRIBUTION_DATE // will be shown during bootup in line 2
+
+// @section machine
+
+// SERIAL_PORT selects which serial port should be used for communication with the host.
+// This allows the connection of wireless adapters (for instance) to non-default port pins.
+// Serial port 0 is still used by the Arduino bootloader regardless of this setting.
+// :[0,1,2,3,4,5,6,7]
+#define SERIAL_PORT 0
+
+// This determines the communication speed of the printer
+// :[2400,9600,19200,38400,57600,115200,250000]
+#define BAUDRATE 250000
+
+// Enable the Bluetooth serial interface on AT90USB devices
+//#define BLUETOOTH
+
+// The following define selects which electronics board you have.
+// Please choose the name from boards.h that matches your setup
+#ifndef MOTHERBOARD
+  #define MOTHERBOARD BOARD_K8400
+#endif
+
+// Optional custom name for your RepStrap or other custom machine
+// Displayed in the LCD "Ready" message
+//#define CUSTOM_MACHINE_NAME "3D Printer"
+
+// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines)
+// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
+//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
+
+// This defines the number of extruders
+// :[1,2,3,4]
+#define EXTRUDERS 1
+
+// For Cyclops or any "multi-extruder" that shares a single nozzle.
+//#define SINGLENOZZLE
+
+// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
+// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
+// For the other hotends it is their distance from the extruder 0 hotend.
+//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
+//#define HOTEND_OFFSET_Y {0.0, 5.00}  // (in mm) for each extruder, offset of the hotend on the Y axis
+
+//// The following define selects which power supply you have. Please choose the one that matches your setup
+// 1 = ATX
+// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
+// :{1:'ATX',2:'X-Box 360'}
+
+#define POWER_SUPPLY 1
+
+// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it.
+//#define PS_DEFAULT_OFF
+
+// @section temperature
+
+//===========================================================================
+//============================= Thermal Settings ============================
+//===========================================================================
+//
+//--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+//
+//// Temperature sensor settings:
+// -3 is thermocouple with MAX31855 (only for sensor 0)
+// -2 is thermocouple with MAX6675 (only for sensor 0)
+// -1 is thermocouple with AD595
+// 0 is not used
+// 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
+// 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
+// 3 is Mendel-parts thermistor (4.7k pullup)
+// 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
+// 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup)
+// 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
+// 7 is 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
+// 71 is 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
+// 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
+// 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
+// 10 is 100k RS thermistor 198-961 (4.7k pullup)
+// 11 is 100k beta 3950 1% thermistor (4.7k pullup)
+// 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
+// 13 is 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
+// 20 is the PT100 circuit found in the Ultimainboard V2.x
+// 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
+// 70 is the 100K thermistor found in the bq Hephestos 2
+//
+//    1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k
+//                          (but gives greater accuracy and more stable PID)
+// 51 is 100k thermistor - EPCOS (1k pullup)
+// 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
+// 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
+//
+// 1047 is Pt1000 with 4k7 pullup
+// 1010 is Pt1000 with 1k pullup (non standard)
+// 147 is Pt100 with 4k7 pullup
+// 110 is Pt100 with 1k pullup (non standard)
+// 998 and 999 are Dummy Tables. They will ALWAYS read 25°C or the temperature defined below.
+//     Use it for Testing or Development purposes. NEVER for production machine.
+//#define DUMMY_THERMISTOR_998_VALUE 25
+//#define DUMMY_THERMISTOR_999_VALUE 100
+// :{ '0': "Not used", '4': "10k !! do not use for a hotend. Bad resolution at high temp. !!", '1': "100k / 4.7k - EPCOS", '51': "100k / 1k - EPCOS", '6': "100k / 4.7k EPCOS - Not as accurate as Table 1", '5': "100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '7': "100k / 4.7k Honeywell 135-104LAG-J01", '71': "100k / 4.7k Honeywell 135-104LAF-J01", '8': "100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9': "100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10': "100k / 4.7k RS 198-961", '11': "100k / 4.7k beta 3950 1%", '12': "100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13': "100k Hisens 3950  1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '60': "100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '55': "100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '2': "200k / 4.7k - ATC Semitec 204GT-2", '52': "200k / 1k - ATC Semitec 204GT-2", '-3': "Thermocouple + MAX31855 (only for sensor 0)", '-2': "Thermocouple + MAX6675 (only for sensor 0)", '-1': "Thermocouple + AD595", '3': "Mendel-parts / 4.7k", '1047': "Pt1000 / 4.7k", '1010': "Pt1000 / 1k (non standard)", '20': "PT100 (Ultimainboard V2.x)", '147': "Pt100 / 4.7k", '110': "Pt100 / 1k (non-standard)", '998': "Dummy 1", '999': "Dummy 2" }
+#define TEMP_SENSOR_0 5
+#define TEMP_SENSOR_1 0
+#define TEMP_SENSOR_2 0
+#define TEMP_SENSOR_3 0
+#define TEMP_SENSOR_BED 0
+
+// This makes temp sensor 1 a redundant sensor for sensor 0. If the temperatures difference between these sensors is to high the print will be aborted.
+//#define TEMP_SENSOR_1_AS_REDUNDANT
+#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
+
+// Extruder temperature must be close to target for this long before M109 returns success
+#define TEMP_RESIDENCY_TIME 2   // (seconds)
+#define TEMP_HYSTERESIS 5       // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
+
+// Bed temperature must be close to target for this long before M190 returns success
+#define TEMP_BED_RESIDENCY_TIME 10  // (seconds)
+#define TEMP_BED_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_BED_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
+
+// The minimal temperature defines the temperature below which the heater will not be enabled It is used
+// to check that the wiring to the thermistor is not broken.
+// Otherwise this would lead to the heater being powered on all the time.
+#define HEATER_0_MINTEMP 5
+#define HEATER_1_MINTEMP 5
+#define HEATER_2_MINTEMP 5
+#define HEATER_3_MINTEMP 5
+#define BED_MINTEMP 5
+
+// When temperature exceeds max temp, your heater will be switched off.
+// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!
+// You should use MINTEMP for thermistor short/failure protection.
+#define HEATER_0_MAXTEMP 275
+#define HEATER_1_MAXTEMP 275
+#define HEATER_2_MAXTEMP 275
+#define HEATER_3_MAXTEMP 275
+#define BED_MAXTEMP 150
+
+// If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS
+//#define HOTEND_WATTS (12.0*12.0/6.7) // P=U^2/R
+//#define BED_WATTS (12.0*12.0/1.1)    // P=U^2/R
+
+//===========================================================================
+//============================= PID Settings ================================
+//===========================================================================
+// PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning
+
+// Comment the following line to disable PID and enable bang-bang.
+#define PIDTEMP
+#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#if ENABLED(PIDTEMP)
+  //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
+  //#define PID_DEBUG // Sends debug data to the serial port.
+  //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
+  //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
+  //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
+                                  // Set/get with gcode: M301 E[extruder number, 0-2]
+  #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
+                                  // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+  #define PID_INTEGRAL_DRIVE_MAX PID_MAX  //limit for the integral term
+  #define K1 0.95 //smoothing factor within the PID
+
+  // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
+  // Ultimaker
+  //#define  DEFAULT_Kp 22.2
+  //#define  DEFAULT_Ki 1.08
+  //#define  DEFAULT_Kd 114
+
+  // MakerGear
+  //#define  DEFAULT_Kp 7.0
+  //#define  DEFAULT_Ki 0.1
+  //#define  DEFAULT_Kd 12
+
+  // Mendel Parts V9 on 12V
+  #define  DEFAULT_Kp 63.0
+  #define  DEFAULT_Ki 2.25
+  #define  DEFAULT_Kd 440
+
+#endif // PIDTEMP
+
+//===========================================================================
+//============================= PID > Bed Temperature Control ===============
+//===========================================================================
+// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
+//
+// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
+// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
+// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
+// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
+// If your configuration is significantly different than this and you don't understand the issues involved, you probably
+// shouldn't use bed PID until someone else verifies your hardware works.
+// If this is enabled, find your own PID constants below.
+//#define PIDTEMPBED
+
+//#define BED_LIMIT_SWITCHING
+
+// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
+// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
+// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
+// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
+
+#if ENABLED(PIDTEMPBED)
+
+  //#define PID_BED_DEBUG // Sends debug data to the serial port.
+
+  #define PID_BED_INTEGRAL_DRIVE_MAX MAX_BED_POWER //limit for the integral term
+
+  //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
+  //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
+  #define  DEFAULT_bedKp 10.00
+  #define  DEFAULT_bedKi .023
+  #define  DEFAULT_bedKd 305.4
+
+  //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
+  //from pidautotune
+  //#define  DEFAULT_bedKp 97.1
+  //#define  DEFAULT_bedKi 1.41
+  //#define  DEFAULT_bedKd 1675.16
+
+  // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
+#endif // PIDTEMPBED
+
+// @section extruder
+
+//this prevents dangerous Extruder moves, i.e. if the temperature is under the limit
+//can be software-disabled for whatever purposes by
+#define PREVENT_DANGEROUS_EXTRUDE
+//if PREVENT_DANGEROUS_EXTRUDE is on, you can still disable (uncomment) very long bits of extrusion separately.
+#define PREVENT_LENGTHY_EXTRUDE
+
+#define EXTRUDE_MINTEMP 160
+#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
+
+//===========================================================================
+//======================== Thermal Runaway Protection =======================
+//===========================================================================
+
+/**
+ * Thermal Protection protects your printer from damage and fire if a
+ * thermistor falls out or temperature sensors fail in any way.
+ *
+ * The issue: If a thermistor falls out or a temperature sensor fails,
+ * Marlin can no longer sense the actual temperature. Since a disconnected
+ * thermistor reads as a low temperature, the firmware will keep the heater on.
+ *
+ * If you get "Thermal Runaway" or "Heating failed" errors the
+ * details can be tuned in Configuration_adv.h
+ */
+
+#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
+#define THERMAL_PROTECTION_BED     // Enable thermal protection for the heated bed
+
+//===========================================================================
+//============================= Mechanical Settings =========================
+//===========================================================================
+
+// @section machine
+
+// Uncomment one of these options to enable CoreXY, CoreXZ, or CoreYZ kinematics
+//#define COREXY
+//#define COREXZ
+//#define COREYZ
+
+// Enable this option for Toshiba steppers
+//#define CONFIG_STEPPERS_TOSHIBA
+
+//===========================================================================
+//============================== Endstop Settings ===========================
+//===========================================================================
+
+// @section homing
+
+// Specify here all the endstop connectors that are connected to any endstop or probe.
+// Almost all printers will be using one per axis. Probes will use one or more of the
+// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
+#define USE_XMIN_PLUG
+#define USE_YMIN_PLUG
+#define USE_ZMIN_PLUG
+//#define USE_XMAX_PLUG
+//#define USE_YMAX_PLUG
+//#define USE_ZMAX_PLUG
+
+// coarse Endstop Settings
+#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
+
+#if DISABLED(ENDSTOPPULLUPS)
+  // fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined
+  //#define ENDSTOPPULLUP_XMAX
+  //#define ENDSTOPPULLUP_YMAX
+  //#define ENDSTOPPULLUP_ZMAX
+  //#define ENDSTOPPULLUP_XMIN
+  //#define ENDSTOPPULLUP_YMIN
+  //#define ENDSTOPPULLUP_ZMIN
+  //#define ENDSTOPPULLUP_ZMIN_PROBE
+#endif
+
+// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
+const bool X_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
+const bool Y_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
+const bool Z_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
+const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
+const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
+const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
+const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
+
+//===========================================================================
+//============================= Z Probe Options =============================
+//===========================================================================
+
+//
+// Probe Type
+// Probes are sensors/switches that are activated / deactivated before/after use.
+//
+// Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc.
+// You must activate one of these to use AUTO_BED_LEVELING_FEATURE below.
+//
+// Use M851 to set the Z probe vertical offset from the nozzle. Store with M500.
+//
+
+// A Fix-Mounted Probe either doesn't deploy or needs manual deployment.
+// For example an inductive probe, or a setup that uses the nozzle to probe.
+// An inductive probe must be deactivated to go below
+// its trigger-point if hardware endstops are active.
+//#define FIX_MOUNTED_PROBE
+
+// Z Servo Probe, such as an endstop switch on a rotating arm.
+//#define Z_ENDSTOP_SERVO_NR 0
+//#define Z_SERVO_ANGLES {70,0} // Z Servo Deploy and Stow angles
+
+// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
+//#define Z_PROBE_SLED
+//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
+
+// Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+// X and Y offsets must be integers.
+//
+// In the following example the X and Y offsets are both positive:
+// #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+// #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+//
+//    +-- BACK ---+
+//    |           |
+//  L |    (+) P  | R <-- probe (20,20)
+//  E |           | I
+//  F | (-) N (+) | G <-- nozzle (10,10)
+//  T |           | H
+//    |    (-)    | T
+//    |           |
+//    O-- FRONT --+
+//  (0,0)
+#define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
+#define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]
+#define Z_PROBE_OFFSET_FROM_EXTRUDER 0   // Z offset: -below +above  [the nozzle]
+
+// X and Y axis travel speed (mm/m) between probes
+#define XY_PROBE_SPEED 8000
+
+//
+// Allen Key Probe is defined in the Delta example configurations.
+//
+
+// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
+// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
+//
+// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
+//
+// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
+// Example: To park the head outside the bed area when homing with G28.
+//
+// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
+//
+// For a servo-based Z probe, you must set up servo support below, including
+// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES.
+//
+// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
+// - Use 5V for powered (usu. inductive) sensors.
+// - Otherwise connect:
+//   - normally-closed switches to GND and D32.
+//   - normally-open switches to 5V and D32.
+//
+// Normally-closed switches are advised and are the default.
+//
+// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
+// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
+// default pin for all RAMPS-based boards. Some other boards map differently.
+// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file.
+//
+// WARNING:
+// Setting the wrong pin may have unexpected and potentially disastrous consequences.
+// Use with caution and do your homework.
+//
+//#define Z_MIN_PROBE_ENDSTOP
+
+// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
+// The Z_MIN_PIN will then be used for both Z-homing and probing.
+#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
+
+// To use a probe you must enable one of the two options above!
+
+// This option disables the use of the Z_MIN_PROBE_PIN
+// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
+// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
+// If you're using the Z MIN endstop connector for your Z probe, this has no effect.
+//#define DISABLE_Z_MIN_PROBE_ENDSTOP
+
+// Enable Z Probe Repeatability test to see how accurate your probe is
+//#define Z_MIN_PROBE_REPEATABILITY_TEST
+
+//
+// Probe Raise options provide clearance for the probe to deploy, stow, and travel.
+//
+#define Z_RAISE_PROBE_DEPLOY_STOW 15 // Raise to make room for the probe to deploy / stow
+#define Z_RAISE_BETWEEN_PROBINGS 5  // Raise between probing points.
+
+//
+// For M851 give a range for adjusting the Z probe offset
+//
+#define Z_PROBE_OFFSET_RANGE_MIN -20
+#define Z_PROBE_OFFSET_RANGE_MAX 20
+
+// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
+// :{0:'Low',1:'High'}
+#define X_ENABLE_ON 0
+#define Y_ENABLE_ON 0
+#define Z_ENABLE_ON 0
+#define E_ENABLE_ON 0 // For all extruders
+
+// Disables axis stepper immediately when it's not being used.
+// WARNING: When motors turn off there is a chance of losing position accuracy!
+#define DISABLE_X false
+#define DISABLE_Y false
+#define DISABLE_Z false
+// Warn on display about possibly reduced accuracy
+//#define DISABLE_REDUCED_ACCURACY_WARNING
+
+// @section extruder
+
+#define DISABLE_E false // For all extruders
+#define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled
+
+// @section machine
+
+// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
+#define INVERT_X_DIR false
+#define INVERT_Y_DIR true
+#define INVERT_Z_DIR true
+
+// @section extruder
+
+// For direct drive extruder v9 set to true, for geared extruder set to false.
+#define INVERT_E0_DIR false
+#define INVERT_E1_DIR true
+#define INVERT_E2_DIR false
+#define INVERT_E3_DIR false
+
+// @section homing
+//#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+                                    // Be sure you have this distance over your Z_MAX_POS in case.
+
+// ENDSTOP SETTINGS:
+// Sets direction of endstops when homing; 1=MAX, -1=MIN
+// :[-1,1]
+#define X_HOME_DIR -1
+#define Y_HOME_DIR -1
+#define Z_HOME_DIR -1
+
+#define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
+#define max_software_endstops true  // If true, axis won't move to coordinates greater than the defined lengths below.
+
+// @section machine
+
+// Travel limits after homing (units are in mm)
+#define X_MIN_POS 0
+#define Y_MIN_POS 20
+#define Z_MIN_POS 0
+#define X_MAX_POS 200
+#define Y_MAX_POS 200
+#define Z_MAX_POS 190
+
+//===========================================================================
+//========================= Filament Runout Sensor ==========================
+//===========================================================================
+//#define FILAMENT_RUNOUT_SENSOR // Uncomment for defining a filament runout sensor such as a mechanical or opto endstop to check the existence of filament
+                                 // In RAMPS uses servo pin 2. Can be changed in pins file. For other boards pin definition should be made.
+                                 // It is assumed that when logic high = filament available
+                                 //                    when logic  low = filament ran out
+#if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  const bool FIL_RUNOUT_INVERTING = false; // set to true to invert the logic of the sensor.
+  #define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
+  #define FILAMENT_RUNOUT_SCRIPT "M600"
+#endif
+
+//===========================================================================
+//============================ Mesh Bed Leveling ============================
+//===========================================================================
+
+//#define MESH_BED_LEVELING    // Enable mesh bed leveling.
+
+#if ENABLED(MESH_BED_LEVELING)
+  #define MESH_INSET 10        // Mesh inset margin on print area
+  #define MESH_NUM_X_POINTS 3  // Don't use more than 7 points per axis, implementation limited.
+  #define MESH_NUM_Y_POINTS 3
+  #define MESH_HOME_SEARCH_Z 4  // Z after Home, bed somewhere below but above 0.0.
+
+  //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest at origin [0,0,0]
+
+  //#define MANUAL_BED_LEVELING  // Add display menu option for bed leveling.
+
+  #if ENABLED(MANUAL_BED_LEVELING)
+    #define MBL_Z_STEP 0.025  // Step size while manually probing Z axis.
+  #endif  // MANUAL_BED_LEVELING
+
+#endif  // MESH_BED_LEVELING
+
+//===========================================================================
+//============================ Bed Auto Leveling ============================
+//===========================================================================
+
+// @section bedlevel
+
+//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
+//#define DEBUG_LEVELING_FEATURE
+
+#if ENABLED(AUTO_BED_LEVELING_FEATURE)
+
+  // There are 2 different ways to specify probing locations:
+  //
+  // - "grid" mode
+  //   Probe several points in a rectangular grid.
+  //   You specify the rectangle and the density of sample points.
+  //   This mode is preferred because there are more measurements.
+  //
+  // - "3-point" mode
+  //   Probe 3 arbitrary points on the bed (that aren't collinear)
+  //   You specify the XY coordinates of all 3 points.
+
+  // Enable this to sample the bed in a grid (least squares solution).
+  // Note: this feature generates 10KB extra code size.
+  #define AUTO_BED_LEVELING_GRID
+
+  #if ENABLED(AUTO_BED_LEVELING_GRID)
+
+    #define LEFT_PROBE_BED_POSITION 15
+    #define RIGHT_PROBE_BED_POSITION 170
+    #define FRONT_PROBE_BED_POSITION 20
+    #define BACK_PROBE_BED_POSITION 170
+
+    #define MIN_PROBE_EDGE 10 // The Z probe minimum square sides can be no smaller than this.
+
+    // Set the number of grid points per dimension.
+    // You probably don't need more than 3 (squared=9).
+    #define AUTO_BED_LEVELING_GRID_POINTS 2
+
+  #else  // !AUTO_BED_LEVELING_GRID
+
+    // Arbitrary points to probe.
+    // A simple cross-product is used to estimate the plane of the bed.
+    #define ABL_PROBE_PT_1_X 15
+    #define ABL_PROBE_PT_1_Y 180
+    #define ABL_PROBE_PT_2_X 15
+    #define ABL_PROBE_PT_2_Y 20
+    #define ABL_PROBE_PT_3_X 170
+    #define ABL_PROBE_PT_3_Y 20
+
+  #endif // !AUTO_BED_LEVELING_GRID
+
+  //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
+                                                                             // Useful to retract a deployable Z probe.
+
+  // If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing,
+  // it is highly recommended you also enable Z_SAFE_HOMING below!
+
+#endif // AUTO_BED_LEVELING_FEATURE
+
+
+// @section homing
+
+// The position of the homing switches
+//#define MANUAL_HOME_POSITIONS  // If defined, MANUAL_*_HOME_POS below will be used
+//#define BED_CENTER_AT_0_0  // If defined, the center of the bed is at (X=0, Y=0)
+
+// Manual homing switch locations:
+// For deltabots this means top and center of the Cartesian print volume.
+#if ENABLED(MANUAL_HOME_POSITIONS)
+  #define MANUAL_X_HOME_POS 0
+  #define MANUAL_Y_HOME_POS 0
+  #define MANUAL_Z_HOME_POS 0
+  //#define MANUAL_Z_HOME_POS 402 // For delta: Distance between nozzle and print surface after homing.
+#endif
+
+// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
+//
+// With this feature enabled:
+//
+// - Allow Z homing only after X and Y homing AND stepper drivers still enabled.
+// - If stepper drivers time out, it will need X and Y homing again before Z homing.
+// - Position the Z probe in a defined XY point before Z Homing when homing all axes (G28).
+// - Prevent Z homing when the Z probe is outside bed area.
+//#define Z_SAFE_HOMING
+
+#if ENABLED(Z_SAFE_HOMING)
+  #define Z_SAFE_HOMING_X_POINT ((X_MIN_POS + X_MAX_POS) / 2)    // X point for Z homing when homing all axis (G28).
+  #define Z_SAFE_HOMING_Y_POINT ((Y_MIN_POS + Y_MAX_POS) / 2)    // Y point for Z homing when homing all axis (G28).
+#endif
+
+
+// @section motion
+
+/**
+ * MOVEMENT SETTINGS
+ */
+
+#define HOMING_FEEDRATE {50*60, 50*60, 8*60, 0}  // set the homing speeds (mm/min)
+
+// default settings
+
+#define DEFAULT_AXIS_STEPS_PER_UNIT   {134.74,134.74,4266.66,148.7}  // default steps per unit for Ultimaker
+#define DEFAULT_MAX_FEEDRATE          {160, 160, 10, 10000}    // (mm/sec)
+#define DEFAULT_MAX_ACCELERATION      {9000,9000,100,10000}    // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
+
+#define DEFAULT_ACCELERATION          6000    // X, Y, Z and E acceleration in mm/s^2 for printing moves
+#define DEFAULT_RETRACT_ACCELERATION  6000    // E acceleration in mm/s^2 for retracts
+#define DEFAULT_TRAVEL_ACCELERATION   3000    // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves
+
+// The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously)
+#define DEFAULT_XYJERK                10.0    // (mm/sec)
+#define DEFAULT_ZJERK                 0.5     // (mm/sec)
+#define DEFAULT_EJERK                 20.0    // (mm/sec)
+
+
+//=============================================================================
+//============================= Additional Features ===========================
+//=============================================================================
+
+// @section extras
+
+//
+// EEPROM
+//
+// The microcontroller can store settings in the EEPROM, e.g. max velocity...
+// M500 - stores parameters in EEPROM
+// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
+// M502 - reverts to the default "factory settings".  You still need to store them in EEPROM afterwards if you want to.
+//define this to enable EEPROM support
+#define EEPROM_SETTINGS
+
+#if ENABLED(EEPROM_SETTINGS)
+  // To disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out:
+  #define EEPROM_CHITCHAT // Please keep turned on if you can.
+#endif
+
+//
+// Host Keepalive
+//
+// When enabled Marlin will send a busy status message to the host
+// every couple of seconds when it can't accept commands.
+//
+#define HOST_KEEPALIVE_FEATURE        // Disable this if your host doesn't like keepalive messages
+#define DEFAULT_KEEPALIVE_INTERVAL 2  // Number of seconds between "busy" messages. Set with M113.
+
+//
+// M100 Free Memory Watcher
+//
+//#define M100_FREE_MEMORY_WATCHER // uncomment to add the M100 Free Memory Watcher for debug purpose
+
+//
+// G20/G21 Inch mode support
+//
+//#define INCH_MODE_SUPPORT
+
+//
+// M149 Set temperature units support
+//
+//#define TEMPERATURE_UNITS_SUPPORT
+
+// @section temperature
+
+// Preheat Constants
+#define PLA_PREHEAT_HOTEND_TEMP 210
+#define PLA_PREHEAT_HPB_TEMP 0
+#define PLA_PREHEAT_FAN_SPEED 165   // Insert Value between 0 and 255
+
+#define ABS_PREHEAT_HOTEND_TEMP 245
+#define ABS_PREHEAT_HPB_TEMP 0
+#define ABS_PREHEAT_FAN_SPEED 165   // Insert Value between 0 and 255
+
+//
+// Print job timer
+//
+// Enable this option to automatically start and stop the
+// print job timer when M104 and M109 commands are received.
+//
+// In all cases the timer can be started and stopped using
+// the following commands:
+//
+// - M75  - Start the print job timer
+// - M76  - Pause the print job timer
+// - M77  - Stop the print job timer
+#define PRINTJOB_TIMER_AUTOSTART
+
+//
+// Print Counter
+//
+// When enabled Marlin will keep track of some print statistical data such as:
+//  - Total print jobs
+//  - Total successful print jobs
+//  - Total failed print jobs
+//  - Total time printing
+//
+// This information can be viewed by the M78 command.
+//#define PRINTCOUNTER
+
+//=============================================================================
+//============================= LCD and SD support ============================
+//=============================================================================
+
+// @section lcd
+
+//
+// LCD LANGUAGE
+//
+// Here you may choose the language used by Marlin on the LCD menus, the following
+// list of languages are available:
+//    en, an, bg, ca, cn, cz, de, es, eu, fi, fr, gl, hr, it, kana,
+//    kana_utf8, nl, pl, pt, pt_utf8, pt-br, pt-br_utf8, ru, test
+//
+// :{'en':'English','an':'Aragonese','bg':'Bulgarian','ca':'Catalan','cn':'Chinese','cz':'Czech','de':'German','es':'Spanish','eu':'Basque-Euskera','fi':'Finnish','fr':'French','gl':'Galician','hr':'Croatian','it':'Italian','kana':'Japanese','kana_utf8':'Japanese (UTF8)','nl':'Dutch','pl':'Polish','pt':'Portuguese','pt-br':'Portuguese (Brazilian)','pt-br_utf8':'Portuguese (Brazilian UTF8)','pt_utf8':'Portuguese (UTF8)','ru':'Russian','test':'TEST'}
+//
+#define LCD_LANGUAGE en
+
+//
+// LCD Character Set
+//
+// Note: This option is NOT applicable to Graphical Displays.
+//
+// All character-based LCD's provide ASCII plus one of these
+// language extensions:
+//
+//  - JAPANESE ... the most common
+//  - WESTERN  ... with more accented characters
+//  - CYRILLIC ... for the Russian language
+//
+// To determine the language extension installed on your controller:
+//
+//  - Compile and upload with LCD_LANGUAGE set to 'test'
+//  - Click the controller to view the LCD menu
+//  - The LCD will display Japanese, Western, or Cyrillic text
+//
+// See https://github.com/MarlinFirmware/Marlin/wiki/LCD-Language
+//
+// :['JAPANESE','WESTERN','CYRILLIC']
+//
+#define DISPLAY_CHARSET_HD44780 JAPANESE
+
+//
+// LCD TYPE
+//
+// You may choose ULTRA_LCD if you have character based LCD with 16x2, 16x4, 20x2,
+// 20x4 char/lines or DOGLCD for the full graphics display with 128x64 pixels
+// (ST7565R family). (This option will be set automatically for certain displays.)
+//
+// IMPORTANT NOTE: The U8glib library is required for Full Graphic Display!
+//                 https://github.com/olikraus/U8glib_Arduino
+//
+#define ULTRA_LCD   // Character based
+//#define DOGLCD      // Full graphics display
+
+//
+// SD CARD
+//
+// SD Card support is disabled by default. If your controller has an SD slot,
+// you must uncomment the following option or it won't work.
+//
+#define SDSUPPORT
+
+//
+// SD CARD: SPI SPEED
+//
+// Uncomment ONE of the following items to use a slower SPI transfer
+// speed. This is usually required if you're getting volume init errors.
+//
+//#define SPI_SPEED SPI_HALF_SPEED
+//#define SPI_SPEED SPI_QUARTER_SPEED
+//#define SPI_SPEED SPI_EIGHTH_SPEED
+
+//
+// SD CARD: ENABLE CRC
+//
+// Use CRC checks and retries on the SD communication.
+//
+//#define SD_CHECK_AND_RETRY
+
+//
+// ENCODER SETTINGS
+//
+// This option overrides the default number of encoder pulses needed to
+// produce one step. Should be increased for high-resolution encoders.
+//
+#define ENCODER_PULSES_PER_STEP 4
+
+//
+// Use this option to override the number of step signals required to
+// move between next/prev menu items.
+//
+#define ENCODER_STEPS_PER_MENU_ITEM 1
+
+/**
+ * Encoder Direction Options
+ *
+ * Test your encoder's behavior first with both options disabled.
+ *
+ *  Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION.
+ *  Reversed Menu Navigation only?    Enable REVERSE_MENU_DIRECTION.
+ *  Reversed Value Editing only?      Enable BOTH options.
+ */
+
+//
+// This option reverses the encoder direction everywhere
+//
+//  Set this option if CLOCKWISE causes values to DECREASE
+//
+//#define REVERSE_ENCODER_DIRECTION
+
+//
+// This option reverses the encoder direction for navigating LCD menus.
+//
+//  If CLOCKWISE normally moves DOWN this makes it go UP.
+//  If CLOCKWISE normally moves UP this makes it go DOWN.
+//
+#define REVERSE_MENU_DIRECTION
+
+//
+// Individual Axis Homing
+//
+// Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
+//
+//#define INDIVIDUAL_AXIS_HOMING_MENU
+
+//
+// SPEAKER/BUZZER
+//
+// If you have a speaker that can produce tones, enable it here.
+// By default Marlin assumes you have a buzzer with a fixed frequency.
+//
+//#define SPEAKER
+
+//
+// The duration and frequency for the UI feedback sound.
+// Set these to 0 to disable audio feedback in the LCD menus.
+//
+// Note: Test audio output with the G-Code:
+//  M300 S<frequency Hz> P<duration ms>
+//
+//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100
+//#define LCD_FEEDBACK_FREQUENCY_HZ 1000
+
+//
+// CONTROLLER TYPE: Standard
+//
+// Marlin supports a wide variety of controllers.
+// Enable one of the following options to specify your controller.
+//
+
+//
+// ULTIMAKER Controller.
+//
+#define ULTIMAKERCONTROLLER
+
+//
+// ULTIPANEL as seen on Thingiverse.
+//
+//#define ULTIPANEL
+
+//
+// Cartesio UI
+// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
+//
+//#define CARTESIO_UI
+
+//
+// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
+// http://reprap.org/wiki/PanelOne
+//
+//#define PANEL_ONE
+
+//
+// MaKr3d Makr-Panel with graphic controller and SD support.
+// http://reprap.org/wiki/MaKr3d_MaKrPanel
+//
+//#define MAKRPANEL
+
+//
+// Activate one of these if you have a Panucatt Devices
+// Viki 2.0 or mini Viki with Graphic LCD
+// http://panucatt.com
+//
+//#define VIKI2
+//#define miniVIKI
+
+//
+// Adafruit ST7565 Full Graphic Controller.
+// https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
+//
+//#define ELB_FULL_GRAPHIC_CONTROLLER
+
+//
+// RepRapDiscount Smart Controller.
+// http://reprap.org/wiki/RepRapDiscount_Smart_Controller
+//
+// Note: Usually sold with a white PCB.
+//
+//#define REPRAP_DISCOUNT_SMART_CONTROLLER
+
+//
+// GADGETS3D G3D LCD/SD Controller
+// http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel
+//
+// Note: Usually sold with a blue PCB.
+//
+//#define G3D_PANEL
+
+//
+// RepRapDiscount FULL GRAPHIC Smart Controller
+// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
+//
+//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
+
+//
+// MakerLab Mini Panel with graphic
+// controller and SD support - http://reprap.org/wiki/Mini_panel
+//
+//#define MINIPANEL
+
+//
+// RepRapWorld REPRAPWORLD_KEYPAD v1.1
+// http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626
+//
+// REPRAPWORLD_KEYPAD_MOVE_STEP sets how much should the robot move when a key
+// is pressed, a value of 10.0 means 10mm per click.
+//
+//#define REPRAPWORLD_KEYPAD
+//#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0
+
+//
+// RigidBot Panel V1.0
+// http://www.inventapart.com/
+//
+//#define RIGIDBOT_PANEL
+
+//
+// BQ LCD Smart Controller shipped by
+// default with the BQ Hephestos 2 and Witbox 2.
+//
+//#define BQ_LCD_SMART_CONTROLLER
+
+//
+// CONTROLLER TYPE: I2C
+//
+// Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
+// library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C
+//
+
+//
+// Elefu RA Board Control Panel
+// http://www.elefu.com/index.php?route=product/product&product_id=53
+//
+//#define RA_CONTROL_PANEL
+
+//
+// Sainsmart YW Robot (LCM1602) LCD Display
+//
+//#define LCD_I2C_SAINSMART_YWROBOT
+
+//
+// Generic LCM1602 LCD adapter
+//
+//#define LCM1602
+
+//
+// PANELOLU2 LCD with status LEDs,
+// separate encoder and click inputs.
+//
+// Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later.
+// For more info: https://github.com/lincomatic/LiquidTWI2
+//
+// Note: The PANELOLU2 encoder click input can either be directly connected to
+// a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1).
+//
+//#define LCD_I2C_PANELOLU2
+
+//
+// Panucatt VIKI LCD with status LEDs,
+// integrated click & L/R/U/D buttons, separate encoder inputs.
+//
+//#define LCD_I2C_VIKI
+
+//
+// SSD1306 OLED full graphics generic display
+//
+//#define U8GLIB_SSD1306
+
+//
+// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
+//
+//#define SAV_3DGLCD
+#if ENABLED(SAV_3DGLCD)
+  //#define U8GLIB_SSD1306
+  #define U8GLIB_SH1106
+#endif
+
+//
+// CONTROLLER TYPE: Shift register panels
+//
+// 2 wire Non-latching LCD SR from https://goo.gl/aJJ4sH
+// LCD configuration: http://reprap.org/wiki/SAV_3D_LCD
+//
+//#define SAV_3DLCD
+
+//=============================================================================
+//=============================== Extra Features ==============================
+//=============================================================================
+
+// @section extras
+
+// Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
+//#define FAST_PWM_FAN
+
+// Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
+// which is not as annoying as with the hardware PWM. On the other hand, if this frequency
+// is too low, you should also increment SOFT_PWM_SCALE.
+//#define FAN_SOFT_PWM
+
+// Incrementing this by 1 will double the software PWM frequency,
+// affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
+// However, control resolution will be halved for each increment;
+// at zero value, there are 128 effective control positions.
+#define SOFT_PWM_SCALE 0
+
+// Temperature status LEDs that display the hotend and bed temperature.
+// If all hotends and bed temperature and temperature setpoint are < 54C then the BLUE led is on.
+// Otherwise the RED led is on. There is 1C hysteresis.
+//#define TEMP_STAT_LEDS
+
+// M240  Triggers a camera by emulating a Canon RC-1 Remote
+// Data from: http://www.doc-diy.net/photo/rc-1_hacked/
+//#define PHOTOGRAPH_PIN     23
+
+// SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure
+//#define SF_ARC_FIX
+
+// Support for the BariCUDA Paste Extruder.
+//#define BARICUDA
+
+//define BlinkM/CyzRgb Support
+//#define BLINKM
+
+/*********************************************************************\
+* R/C SERVO support
+* Sponsored by TrinityLabs, Reworked by codexmas
+**********************************************************************/
+
+// Number of servos
+//
+// If you select a configuration below, this will receive a default value and does not need to be set manually
+// set it manually if you have more servos than extruders and wish to manually control some
+// leaving it undefined or defining as 0 will disable the servo subsystem
+// If unsure, leave commented / disabled
+//
+//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
+
+// Delay (in microseconds) before the next move will start, to give the servo time to reach its target angle.
+// 300ms is a good value but you can try less delay.
+// If the servo can't reach the requested position, increase it.
+#define SERVO_DELAY 300
+
+// Servo deactivation
+//
+// With this option servos are powered only during movement, then turned off to prevent jitter.
+//#define DEACTIVATE_SERVOS_AFTER_MOVE
+
+/**********************************************************************\
+ * Support for a filament diameter sensor
+ * Also allows adjustment of diameter at print time (vs  at slicing)
+ * Single extruder only at this point (extruder 0)
+ *
+ * Motherboards
+ * 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector
+ * 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E)
+ * 301 - Rambo  - uses Analog input 3
+ * Note may require analog pins to be defined for different motherboards
+ **********************************************************************/
+// Uncomment below to enable
+//#define FILAMENT_WIDTH_SENSOR
+
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00  //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software.  Used for sensor reading validation
+
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
+  #define FILAMENT_SENSOR_EXTRUDER_NUM 0   //The number of the extruder that has the filament sensor (0,1,2)
+  #define MEASUREMENT_DELAY_CM        14   //measurement delay in cm.  This is the distance from filament sensor to middle of barrel
+
+  #define MEASURED_UPPER_LIMIT         3.30  //upper limit factor used for sensor reading validation in mm
+  #define MEASURED_LOWER_LIMIT         1.90  //lower limit factor for sensor reading validation in mm
+  #define MAX_MEASUREMENT_DELAY       20     //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM  and lower number saves RAM)
+
+  #define DEFAULT_MEASURED_FILAMENT_DIA  DEFAULT_NOMINAL_FILAMENT_DIA  //set measured to nominal initially
+
+  //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status.  Status will appear for 5 sec.
+  //#define FILAMENT_LCD_DISPLAY
+#endif
+
+#include "Configuration_adv.h"
+#include "thermistortables.h"
+
+#endif //CONFIGURATION_H
diff --git a/Marlin/example_configurations/K8400/Configuration_adv.h b/Marlin/example_configurations/K8400/Configuration_adv.h
new file mode 100644
index 0000000000..29b759d17b
--- /dev/null
+++ b/Marlin/example_configurations/K8400/Configuration_adv.h
@@ -0,0 +1,750 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Configuration_adv.h
+ *
+ * Advanced settings.
+ * Only change these if you know exactly what you're doing.
+ * Some of these settings can damage your printer if improperly set!
+ *
+ * Basic settings can be found in Configuration.h
+ *
+ */
+#ifndef CONFIGURATION_ADV_H
+#define CONFIGURATION_ADV_H
+
+/**
+ *
+ *  ***********************************
+ *  **  ATTENTION TO ALL DEVELOPERS  **
+ *  ***********************************
+ *
+ * You must increment this version number for every significant change such as,
+ * but not limited to: ADD, DELETE RENAME OR REPURPOSE any directive/option.
+ *
+ * Note: Update also Version.h !
+ */
+#define CONFIGURATION_ADV_H_VERSION 010100
+
+#include "Conditionals.h"
+
+// @section temperature
+
+//===========================================================================
+//=============================Thermal Settings  ============================
+//===========================================================================
+
+#if DISABLED(PIDTEMPBED)
+  #define BED_CHECK_INTERVAL 1000 // ms between checks in bang-bang control
+  #if ENABLED(BED_LIMIT_SWITCHING)
+    #define BED_HYSTERESIS 1 // Only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS
+  #endif
+#endif
+
+/**
+ * Thermal Protection protects your printer from damage and fire if a
+ * thermistor falls out or temperature sensors fail in any way.
+ *
+ * The issue: If a thermistor falls out or a temperature sensor fails,
+ * Marlin can no longer sense the actual temperature. Since a disconnected
+ * thermistor reads as a low temperature, the firmware will keep the heater on.
+ *
+ * The solution: Once the temperature reaches the target, start observing.
+ * If the temperature stays too far below the target (hysteresis) for too long (period),
+ * the firmware will halt the machine as a safety precaution.
+ *
+ * If you get false positives for "Thermal Runaway" increase THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
+ */
+#if ENABLED(THERMAL_PROTECTION_HOTENDS)
+  #define THERMAL_PROTECTION_PERIOD 40        // Seconds
+  #define THERMAL_PROTECTION_HYSTERESIS 4     // Degrees Celsius
+
+  /**
+   * Whenever an M104 or M109 increases the target temperature the firmware will wait for the
+   * WATCH_TEMP_PERIOD to expire, and if the temperature hasn't increased by WATCH_TEMP_INCREASE
+   * degrees, the machine is halted, requiring a hard reset. This test restarts with any M104/M109,
+   * but only if the current temperature is far enough below the target for a reliable test.
+   *
+   * If you get false positives for "Heating failed" increase WATCH_TEMP_PERIOD and/or decrease WATCH_TEMP_INCREASE
+   * WATCH_TEMP_INCREASE should not be below 2.
+   */
+  #define WATCH_TEMP_PERIOD 20                // Seconds
+  #define WATCH_TEMP_INCREASE 2               // Degrees Celsius
+#endif
+
+/**
+ * Thermal Protection parameters for the bed are just as above for hotends.
+ */
+#if ENABLED(THERMAL_PROTECTION_BED)
+  #define THERMAL_PROTECTION_BED_PERIOD 20    // Seconds
+  #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
+
+  /**
+   * Whenever an M140 or M190 increases the target temperature the firmware will wait for the
+   * WATCH_BED_TEMP_PERIOD to expire, and if the temperature hasn't increased by WATCH_BED_TEMP_INCREASE
+   * degrees, the machine is halted, requiring a hard reset. This test restarts with any M140/M190,
+   * but only if the current temperature is far enough below the target for a reliable test.
+   *
+   * If you get too many "Heating failed" errors, increase WATCH_BED_TEMP_PERIOD and/or decrease
+   * WATCH_BED_TEMP_INCREASE. (WATCH_BED_TEMP_INCREASE should not be below 2.)
+   */
+  #define WATCH_BED_TEMP_PERIOD 60                // Seconds
+  #define WATCH_BED_TEMP_INCREASE 2               // Degrees Celsius
+#endif
+
+#if ENABLED(PIDTEMP)
+  // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
+  // if Kc is chosen well, the additional required power due to increased melting should be compensated.
+  #define PID_ADD_EXTRUSION_RATE
+  #if ENABLED(PID_ADD_EXTRUSION_RATE)
+    #define DEFAULT_Kc (100) //heating power=Kc*(e_speed)
+    #define LPQ_MAX_LEN 50
+  #endif
+#endif
+
+/**
+ * Automatic Temperature:
+ * The hotend target temperature is calculated by all the buffered lines of gcode.
+ * The maximum buffered steps/sec of the extruder motor is called "se".
+ * Start autotemp mode with M109 S<mintemp> B<maxtemp> F<factor>
+ * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by
+ * mintemp and maxtemp. Turn this off by executing M109 without F*
+ * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
+ * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
+ */
+#define AUTOTEMP
+#if ENABLED(AUTOTEMP)
+  #define AUTOTEMP_OLDWEIGHT 0.98
+#endif
+
+//Show Temperature ADC value
+//The M105 command return, besides traditional information, the ADC value read from temperature sensors.
+//#define SHOW_TEMP_ADC_VALUES
+
+// @section extruder
+
+//  extruder run-out prevention.
+//if the machine is idle, and the temperature over MINTEMP, every couple of SECONDS some filament is extruded
+//#define EXTRUDER_RUNOUT_PREVENT
+#define EXTRUDER_RUNOUT_MINTEMP 190
+#define EXTRUDER_RUNOUT_SECONDS 30
+#define EXTRUDER_RUNOUT_ESTEPS 14   // mm filament
+#define EXTRUDER_RUNOUT_SPEED 1500  // extrusion speed
+#define EXTRUDER_RUNOUT_EXTRUDE 100
+
+// @section temperature
+
+//These defines help to calibrate the AD595 sensor in case you get wrong temperature measurements.
+//The measured temperature is defined as "actualTemp = (measuredTemp * TEMP_SENSOR_AD595_GAIN) + TEMP_SENSOR_AD595_OFFSET"
+#define TEMP_SENSOR_AD595_OFFSET 0.0
+#define TEMP_SENSOR_AD595_GAIN   1.0
+
+//This is for controlling a fan to cool down the stepper drivers
+//it will turn on when any driver is enabled
+//and turn off after the set amount of seconds from last driver being disabled again
+#define CONTROLLERFAN_PIN 2 //Pin used for the fan to cool controller (-1 to disable)
+#define CONTROLLERFAN_SECS 60 //How many seconds, after all motors were disabled, the fan should run
+#define CONTROLLERFAN_SPEED 255  // == full speed
+
+// When first starting the main fan, run it at full speed for the
+// given number of milliseconds.  This gets the fan spinning reliably
+// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
+//#define FAN_KICKSTART_TIME 100
+
+// This defines the minimal speed for the main fan, run in PWM mode
+// to enable uncomment and set minimal PWM speed for reliable running (1-255)
+// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
+//#define FAN_MIN_PWM 50
+
+// @section extruder
+
+// Extruder cooling fans
+// Configure fan pin outputs to automatically turn on/off when the associated
+// extruder temperature is above/below EXTRUDER_AUTO_FAN_TEMPERATURE.
+// Multiple extruders can be assigned to the same pin in which case
+// the fan will turn on when any selected extruder is above the threshold.
+#define EXTRUDER_0_AUTO_FAN_PIN -1
+#define EXTRUDER_1_AUTO_FAN_PIN -1
+#define EXTRUDER_2_AUTO_FAN_PIN -1
+#define EXTRUDER_3_AUTO_FAN_PIN -1
+#define EXTRUDER_AUTO_FAN_TEMPERATURE 50
+#define EXTRUDER_AUTO_FAN_SPEED   255  // == full speed
+
+
+//===========================================================================
+//=============================Mechanical Settings===========================
+//===========================================================================
+
+// @section homing
+
+#define ENDSTOPS_ONLY_FOR_HOMING // If defined the endstops will only be used for homing
+
+// @section extras
+
+//#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats.
+
+// A single Z stepper driver is usually used to drive 2 stepper motors.
+// Uncomment this define to utilize a separate stepper driver for each Z axis motor.
+// Only a few motherboards support this, like RAMPS, which have dual extruder support (the 2nd, often unused, extruder driver is used
+// to control the 2nd Z axis stepper motor). The pins are currently only defined for a RAMPS motherboards.
+// On a RAMPS (or other 5 driver) motherboard, using this feature will limit you to using 1 extruder.
+//#define Z_DUAL_STEPPER_DRIVERS
+
+#if ENABLED(Z_DUAL_STEPPER_DRIVERS)
+
+  // Z_DUAL_ENDSTOPS is a feature to enable the use of 2 endstops for both Z steppers - Let's call them Z stepper and Z2 stepper.
+  // That way the machine is capable to align the bed during home, since both Z steppers are homed.
+  // There is also an implementation of M666 (software endstops adjustment) to this feature.
+  // After Z homing, this adjustment is applied to just one of the steppers in order to align the bed.
+  // One just need to home the Z axis and measure the distance difference between both Z axis and apply the math: Z adjust = Z - Z2.
+  // If the Z stepper axis is closer to the bed, the measure Z > Z2 (yes, it is.. think about it) and the Z adjust would be positive.
+  // Play a little bit with small adjustments (0.5mm) and check the behaviour.
+  // The M119 (endstops report) will start reporting the Z2 Endstop as well.
+
+  //#define Z_DUAL_ENDSTOPS
+
+  #if ENABLED(Z_DUAL_ENDSTOPS)
+    #define Z2_USE_ENDSTOP _XMAX_
+  #endif
+
+#endif // Z_DUAL_STEPPER_DRIVERS
+
+// Same again but for Y Axis.
+//#define Y_DUAL_STEPPER_DRIVERS
+
+#if ENABLED(Y_DUAL_STEPPER_DRIVERS)
+  // Define if the two Y drives need to rotate in opposite directions
+  #define INVERT_Y2_VS_Y_DIR true
+#endif
+
+// Enable this for dual x-carriage printers.
+// A dual x-carriage design has the advantage that the inactive extruder can be parked which
+// prevents hot-end ooze contaminating the print. It also reduces the weight of each x-carriage
+// allowing faster printing speeds. Connect your X2 stepper to the first unused E plug.
+//#define DUAL_X_CARRIAGE
+#if ENABLED(DUAL_X_CARRIAGE)
+  // Configuration for second X-carriage
+  // Note: the first x-carriage is defined as the x-carriage which homes to the minimum endstop;
+  // the second x-carriage always homes to the maximum endstop.
+  #define X2_MIN_POS 80     // set minimum to ensure second x-carriage doesn't hit the parked first X-carriage
+  #define X2_MAX_POS 353    // set maximum to the distance between toolheads when both heads are homed
+  #define X2_HOME_DIR 1     // the second X-carriage always homes to the maximum endstop position
+  #define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position
+      // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software
+      // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops
+      // without modifying the firmware (through the "M218 T1 X???" command).
+      // Remember: you should set the second extruder x-offset to 0 in your slicer.
+
+  // There are a few selectable movement modes for dual x-carriages using M605 S<mode>
+  //    Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results
+  //                           as long as it supports dual x-carriages. (M605 S0)
+  //    Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so
+  //                           that additional slicer support is not required. (M605 S1)
+  //    Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all
+  //                           actions of the first x-carriage. This allows the printer to print 2 arbitrary items at
+  //                           once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm])
+
+  // This is the default power-up mode which can be later using M605.
+  #define DEFAULT_DUAL_X_CARRIAGE_MODE 0
+
+  // Default settings in "Auto-park Mode"
+  #define TOOLCHANGE_PARK_ZLIFT   0.2      // the distance to raise Z axis when parking an extruder
+  #define TOOLCHANGE_UNPARK_ZLIFT 1        // the distance to raise Z axis when unparking an extruder
+
+  // Default x offset in duplication mode (typically set to half print bed width)
+  #define DEFAULT_DUPLICATION_X_OFFSET 100
+
+#endif //DUAL_X_CARRIAGE
+
+// @section homing
+
+//homing hits the endstop, then retracts by this distance, before it tries to slowly bump again:
+#define X_HOME_BUMP_MM 10
+#define Y_HOME_BUMP_MM 10
+#define Z_HOME_BUMP_MM 3
+#define HOMING_BUMP_DIVISOR {2, 2, 4}  // Re-Bump Speed Divisor (Divides the Homing Feedrate)
+#define QUICK_HOME  //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
+
+// When G28 is called, this option will make Y home before X
+//#define HOME_Y_BEFORE_X
+
+// @section machine
+
+#define AXIS_RELATIVE_MODES {false, false, false, false}
+
+//By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step.
+#define INVERT_X_STEP_PIN false
+#define INVERT_Y_STEP_PIN false
+#define INVERT_Z_STEP_PIN false
+#define INVERT_E_STEP_PIN false
+
+// Default stepper release if idle. Set to 0 to deactivate.
+// Steppers will shut down DEFAULT_STEPPER_DEACTIVE_TIME seconds after the last move when DISABLE_INACTIVE_? is true.
+// Time can be set by M18 and M84.
+#define DEFAULT_STEPPER_DEACTIVE_TIME 120
+#define DISABLE_INACTIVE_X true
+#define DISABLE_INACTIVE_Y true
+#define DISABLE_INACTIVE_Z true  // set to false if the nozzle will fall down on your printed part when print has finished.
+#define DISABLE_INACTIVE_E true
+
+#define DEFAULT_MINIMUMFEEDRATE       0.0     // minimum feedrate
+#define DEFAULT_MINTRAVELFEEDRATE     0.0
+
+// @section lcd
+
+#if ENABLED(ULTIPANEL)
+  #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel
+  #define ULTIPANEL_FEEDMULTIPLY  // Comment to disable setting feedrate multiplier via encoder
+#endif
+
+// @section extras
+
+// minimum time in microseconds that a movement needs to take if the buffer is emptied.
+#define DEFAULT_MINSEGMENTTIME        20000
+
+// If defined the movements slow down when the look ahead buffer is only half full
+#define SLOWDOWN
+
+// Frequency limit
+// See nophead's blog for more info
+// Not working O
+//#define XY_FREQUENCY_LIMIT  15
+
+// Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
+// of the buffer and all stops. This should not be much greater than zero and should only be changed
+// if unwanted behavior is observed on a user's machine when running at very slow speeds.
+#define MINIMUM_PLANNER_SPEED 0.05// (mm/sec)
+
+// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
+#define MICROSTEP_MODES {16,16,16,16,16} // [1,2,4,8,16]
+
+// Motor Current setting (Only functional when motor driver current ref pins are connected to a digital trimpot on supported boards)
+#define DIGIPOT_MOTOR_CURRENT {135,135,135,135,135} // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A)
+
+// Motor Current controlled via PWM (Overridable on supported boards with PWM-driven motor driver current)
+//#define PWM_MOTOR_CURRENT {1300, 1300, 1250} // Values in milliamps
+
+// uncomment to enable an I2C based DIGIPOT like on the Azteeg X3 Pro
+//#define DIGIPOT_I2C
+// Number of channels available for I2C digipot, For Azteeg X3 Pro we have 8
+#define DIGIPOT_I2C_NUM_CHANNELS 8
+// actual motor currents in Amps, need as many here as DIGIPOT_I2C_NUM_CHANNELS
+#define DIGIPOT_I2C_MOTOR_CURRENTS {1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0}
+
+//===========================================================================
+//=============================Additional Features===========================
+//===========================================================================
+
+#define ENCODER_RATE_MULTIPLIER         // If defined, certain menu edit operations automatically multiply the steps when the encoder is moved quickly
+#define ENCODER_10X_STEPS_PER_SEC 75    // If the encoder steps per sec exceeds this value, multiply steps moved x10 to quickly advance the value
+#define ENCODER_100X_STEPS_PER_SEC 160  // If the encoder steps per sec exceeds this value, multiply steps moved x100 to really quickly advance the value
+
+//#define CHDK 4        //Pin for triggering CHDK to take a picture see how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
+#define CHDK_DELAY 50 //How long in ms the pin should stay HIGH before going LOW again
+
+// @section lcd
+
+// Include a page of printer information in the LCD Main Menu
+//#define LCD_INFO_MENU
+
+#if ENABLED(SDSUPPORT)
+
+  // Some RAMPS and other boards don't detect when an SD card is inserted. You can work
+  // around this by connecting a push button or single throw switch to the pin defined
+  // as SD_DETECT_PIN in your board's pins definitions.
+  // This setting should be disabled unless you are using a push button, pulling the pin to ground.
+  // Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER).
+  #define SD_DETECT_INVERTED
+
+  #define SD_FINISHED_STEPPERRELEASE true  //if sd support and the file is finished: disable steppers?
+  #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
+
+  #define SDCARD_RATHERRECENTFIRST  //reverse file order of sd card menu display. Its sorted practically after the file system block order.
+  // if a file is deleted, it frees a block. hence, the order is not purely chronological. To still have auto0.g accessible, there is again the option to do that.
+  // using:
+  //#define MENU_ADDAUTOSTART
+
+  // Show a progress bar on HD44780 LCDs for SD printing
+  //#define LCD_PROGRESS_BAR
+
+  #if ENABLED(LCD_PROGRESS_BAR)
+    // Amount of time (ms) to show the bar
+    #define PROGRESS_BAR_BAR_TIME 2000
+    // Amount of time (ms) to show the status message
+    #define PROGRESS_BAR_MSG_TIME 3000
+    // Amount of time (ms) to retain the status message (0=forever)
+    #define PROGRESS_MSG_EXPIRE   0
+    // Enable this to show messages for MSG_TIME then hide them
+    //#define PROGRESS_MSG_ONCE
+  #endif
+
+  // This allows hosts to request long names for files and folders with M33
+  //#define LONG_FILENAME_HOST_SUPPORT
+
+  // This option allows you to abort SD printing when any endstop is triggered.
+  // This feature must be enabled with "M540 S1" or from the LCD menu.
+  // To have any effect, endstops must be enabled during SD printing.
+  // With ENDSTOPS_ONLY_FOR_HOMING you must send "M120" to enable endstops.
+  //#define ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED
+
+#endif // SDSUPPORT
+
+// for dogm lcd displays you can choose some additional fonts:
+#if ENABLED(DOGLCD)
+  // save 3120 bytes of PROGMEM by commenting out #define USE_BIG_EDIT_FONT
+  // we don't have a big font for Cyrillic, Kana
+  //#define USE_BIG_EDIT_FONT
+
+  // If you have spare 2300Byte of progmem and want to use a
+  // smaller font on the Info-screen uncomment the next line.
+  //#define USE_SMALL_INFOFONT
+#endif // DOGLCD
+
+// @section safety
+
+// The hardware watchdog should reset the microcontroller disabling all outputs,
+// in case the firmware gets stuck and doesn't do temperature regulation.
+#define USE_WATCHDOG
+
+#if ENABLED(USE_WATCHDOG)
+  // If you have a watchdog reboot in an ArduinoMega2560 then the device will hang forever, as a watchdog reset will leave the watchdog on.
+  // The "WATCHDOG_RESET_MANUAL" goes around this by not using the hardware reset.
+  //  However, THIS FEATURE IS UNSAFE!, as it will only work if interrupts are disabled. And the code could hang in an interrupt routine with interrupts disabled.
+  //#define WATCHDOG_RESET_MANUAL
+#endif
+
+// @section lcd
+
+// Babystepping enables the user to control the axis in tiny amounts, independently from the normal printing process
+// it can e.g. be used to change z-positions in the print startup phase in real-time
+// does not respect endstops!
+//#define BABYSTEPPING
+#if ENABLED(BABYSTEPPING)
+  #define BABYSTEP_XY  //not only z, but also XY in the menu. more clutter, more functions
+                       //not implemented for deltabots!
+  #define BABYSTEP_INVERT_Z false  //true for inverse movements in Z
+  #define BABYSTEP_MULTIPLICATOR 1 //faster movements
+#endif
+
+// @section extruder
+
+// extruder advance constant (s2/mm3)
+//
+// advance (steps) = STEPS_PER_CUBIC_MM_E * EXTRUDER_ADVANCE_K * cubic mm per second ^ 2
+//
+// Hooke's law says:    force = k * distance
+// Bernoulli's principle says:  v ^ 2 / 2 + g . h + pressure / density = constant
+// so: v ^ 2 is proportional to number of steps we advance the extruder
+//#define ADVANCE
+
+#if ENABLED(ADVANCE)
+  #define EXTRUDER_ADVANCE_K .0
+  #define D_FILAMENT 2.85
+#endif
+
+// Implementation of a linear pressure control
+// Assumption: advance = k * (delta velocity)
+// K=0 means advance disabled. A good value for a gregs wade extruder will be around K=75
+//#define LIN_ADVANCE
+
+#if ENABLED(LIN_ADVANCE)
+  #define LIN_ADVANCE_K 75
+#endif
+
+// @section leveling
+
+// Default mesh area is an area with an inset margin on the print area.
+// Below are the macros that are used to define the borders for the mesh area,
+// made available here for specialized needs, ie dual extruder setup.
+#if ENABLED(MESH_BED_LEVELING)
+  #define MESH_MIN_X (X_MIN_POS + MESH_INSET)
+  #define MESH_MAX_X (X_MAX_POS - (MESH_INSET))
+  #define MESH_MIN_Y (Y_MIN_POS + MESH_INSET)
+  #define MESH_MAX_Y (Y_MAX_POS - (MESH_INSET))
+#endif
+
+// @section extras
+
+// Arc interpretation settings:
+#define ARC_SUPPORT  // Disabling this saves ~2738 bytes
+#define MM_PER_ARC_SEGMENT 1
+#define N_ARC_CORRECTION 25
+
+// Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes.
+//#define BEZIER_CURVE_SUPPORT
+
+const unsigned int dropsegments = 5; //everything with less than this number of steps will be ignored as move and joined with the next movement
+
+// @section temperature
+
+// Control heater 0 and heater 1 in parallel.
+//#define HEATERS_PARALLEL
+
+//===========================================================================
+//================================= Buffers =================================
+//===========================================================================
+
+// @section hidden
+
+// The number of linear motions that can be in the plan at any give time.
+// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ring-buffering.
+#if ENABLED(SDSUPPORT)
+  #define BLOCK_BUFFER_SIZE 16   // SD,LCD,Buttons take more memory, block buffer needs to be smaller
+#else
+  #define BLOCK_BUFFER_SIZE 16 // maximize block buffer
+#endif
+
+// @section serial
+
+// The ASCII buffer for serial input
+#define MAX_CMD_SIZE 96
+#define BUFSIZE 26
+
+// Bad Serial-connections can miss a received command by sending an 'ok'
+// Therefore some clients abort after 30 seconds in a timeout.
+// Some other clients start sending commands while receiving a 'wait'.
+// This "wait" is only sent when the buffer is empty. 1 second is a good value here.
+//#define NO_TIMEOUTS 1000 // Milliseconds
+
+// Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary.
+//#define ADVANCED_OK
+
+// @section fwretract
+
+// Firmware based and LCD controlled retract
+// M207 and M208 can be used to define parameters for the retraction.
+// The retraction can be called by the slicer using G10 and G11
+// until then, intended retractions can be detected by moves that only extrude and the direction.
+// the moves are than replaced by the firmware controlled ones.
+
+//#define FWRETRACT  //ONLY PARTIALLY TESTED
+#if ENABLED(FWRETRACT)
+  #define MIN_RETRACT 0.1                //minimum extruded mm to accept a automatic gcode retraction attempt
+  #define RETRACT_LENGTH 3               //default retract length (positive mm)
+  #define RETRACT_LENGTH_SWAP 13         //default swap retract length (positive mm), for extruder change
+  #define RETRACT_FEEDRATE 45            //default feedrate for retracting (mm/s)
+  #define RETRACT_ZLIFT 0                //default retract Z-lift
+  #define RETRACT_RECOVER_LENGTH 0       //default additional recover length (mm, added to retract length when recovering)
+  #define RETRACT_RECOVER_LENGTH_SWAP 0  //default additional swap recover length (mm, added to retract length when recovering from extruder change)
+  #define RETRACT_RECOVER_FEEDRATE 8     //default feedrate for recovering from retraction (mm/s)
+#endif
+
+// Add support for experimental filament exchange support M600; requires display
+#if ENABLED(ULTIPANEL)
+  #define FILAMENT_CHANGE_FEATURE               // Enable filament exchange menu and M600 g-code (used for runout sensor too)
+  #if ENABLED(FILAMENT_CHANGE_FEATURE)
+    #define FILAMENT_CHANGE_X_POS 100           // X position of hotend
+    #define FILAMENT_CHANGE_Y_POS 100           // Y position of hotend
+    #define FILAMENT_CHANGE_Z_ADD 20            // Z addition of hotend (lift)
+    #define FILAMENT_CHANGE_XY_FEEDRATE 100     // X and Y axes feedrate in mm/s (also used for delta printers Z axis)
+    #define FILAMENT_CHANGE_Z_FEEDRATE 5        // Z axis feedrate in mm/s (not used for delta printers)
+    #define FILAMENT_CHANGE_RETRACT_LENGTH 5    // Initial retract in mm
+                                                // It is a short retract used immediately after print interrupt before move to filament exchange position
+    #define FILAMENT_CHANGE_RETRACT_FEEDRATE 60 // Initial retract feedrate in mm/s
+    #define FILAMENT_CHANGE_UNLOAD_LENGTH 600   // Unload filament length from hotend in mm
+                                                // Longer length for bowden printers to unload filament from whole bowden tube,
+                                                // shorter lenght for printers without bowden to unload filament from extruder only,
+                                                // 0 to disable unloading for manual unloading
+    #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10  // Unload filament feedrate in mm/s - filament unloading can be fast
+    #define FILAMENT_CHANGE_LOAD_LENGTH 600     // Load filament length over hotend in mm
+                                                // Longer length for bowden printers to fast load filament into whole bowden tube over the hotend,
+                                                // Short or zero length for printers without bowden where loading is not used
+    #define FILAMENT_CHANGE_LOAD_FEEDRATE 10    // Load filament feedrate in mm/s - filament loading into the bowden tube can be fast
+    #define FILAMENT_CHANGE_EXTRUDE_LENGTH 100  // Extrude filament length in mm after filament is load over the hotend,
+                                                // 0 to disable for manual extrusion
+                                                // Filament can be extruded repeatedly from the filament exchange menu to fill the hotend,
+                                                // or until outcoming filament color is not clear for filament color change
+    #define FILAMENT_CHANGE_EXTRUDE_FEEDRATE 3  // Extrude filament feedrate in mm/s - must be slower than load feedrate
+  #endif
+#endif
+
+/******************************************************************************\
+ * enable this section if you have TMC26X motor drivers.
+ * you need to import the TMC26XStepper library into the Arduino IDE for this
+ ******************************************************************************/
+
+// @section tmc
+
+//#define HAVE_TMCDRIVER
+#if ENABLED(HAVE_TMCDRIVER)
+
+  //#define X_IS_TMC
+  #define X_MAX_CURRENT 1000  //in mA
+  #define X_SENSE_RESISTOR 91 //in mOhms
+  #define X_MICROSTEPS 16     //number of microsteps
+
+  //#define X2_IS_TMC
+  #define X2_MAX_CURRENT 1000  //in mA
+  #define X2_SENSE_RESISTOR 91 //in mOhms
+  #define X2_MICROSTEPS 16     //number of microsteps
+
+  //#define Y_IS_TMC
+  #define Y_MAX_CURRENT 1000  //in mA
+  #define Y_SENSE_RESISTOR 91 //in mOhms
+  #define Y_MICROSTEPS 16     //number of microsteps
+
+  //#define Y2_IS_TMC
+  #define Y2_MAX_CURRENT 1000  //in mA
+  #define Y2_SENSE_RESISTOR 91 //in mOhms
+  #define Y2_MICROSTEPS 16     //number of microsteps
+
+  //#define Z_IS_TMC
+  #define Z_MAX_CURRENT 1000  //in mA
+  #define Z_SENSE_RESISTOR 91 //in mOhms
+  #define Z_MICROSTEPS 16     //number of microsteps
+
+  //#define Z2_IS_TMC
+  #define Z2_MAX_CURRENT 1000  //in mA
+  #define Z2_SENSE_RESISTOR 91 //in mOhms
+  #define Z2_MICROSTEPS 16     //number of microsteps
+
+  //#define E0_IS_TMC
+  #define E0_MAX_CURRENT 1000  //in mA
+  #define E0_SENSE_RESISTOR 91 //in mOhms
+  #define E0_MICROSTEPS 16     //number of microsteps
+
+  //#define E1_IS_TMC
+  #define E1_MAX_CURRENT 1000  //in mA
+  #define E1_SENSE_RESISTOR 91 //in mOhms
+  #define E1_MICROSTEPS 16     //number of microsteps
+
+  //#define E2_IS_TMC
+  #define E2_MAX_CURRENT 1000  //in mA
+  #define E2_SENSE_RESISTOR 91 //in mOhms
+  #define E2_MICROSTEPS 16     //number of microsteps
+
+  //#define E3_IS_TMC
+  #define E3_MAX_CURRENT 1000  //in mA
+  #define E3_SENSE_RESISTOR 91 //in mOhms
+  #define E3_MICROSTEPS 16     //number of microsteps
+
+#endif
+
+/******************************************************************************\
+ * enable this section if you have L6470  motor drivers.
+ * you need to import the L6470 library into the Arduino IDE for this
+ ******************************************************************************/
+
+// @section l6470
+
+//#define HAVE_L6470DRIVER
+#if ENABLED(HAVE_L6470DRIVER)
+
+  //#define X_IS_L6470
+  #define X_MICROSTEPS 16     //number of microsteps
+  #define X_K_VAL 50          // 0 - 255, Higher values, are higher power. Be careful not to go too high
+  #define X_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+  #define X_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+
+  //#define X2_IS_L6470
+  #define X2_MICROSTEPS 16     //number of microsteps
+  #define X2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be careful not to go too high
+  #define X2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+  #define X2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+
+  //#define Y_IS_L6470
+  #define Y_MICROSTEPS 16     //number of microsteps
+  #define Y_K_VAL 50          // 0 - 255, Higher values, are higher power. Be careful not to go too high
+  #define Y_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+  #define Y_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+
+  //#define Y2_IS_L6470
+  #define Y2_MICROSTEPS 16     //number of microsteps
+  #define Y2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be careful not to go too high
+  #define Y2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+  #define Y2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+
+  //#define Z_IS_L6470
+  #define Z_MICROSTEPS 16     //number of microsteps
+  #define Z_K_VAL 50          // 0 - 255, Higher values, are higher power. Be careful not to go too high
+  #define Z_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+  #define Z_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+
+  //#define Z2_IS_L6470
+  #define Z2_MICROSTEPS 16     //number of microsteps
+  #define Z2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be careful not to go too high
+  #define Z2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+  #define Z2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+
+  //#define E0_IS_L6470
+  #define E0_MICROSTEPS 16     //number of microsteps
+  #define E0_K_VAL 50          // 0 - 255, Higher values, are higher power. Be careful not to go too high
+  #define E0_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+  #define E0_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+
+  //#define E1_IS_L6470
+  #define E1_MICROSTEPS 16     //number of microsteps
+  #define E1_K_VAL 50          // 0 - 255, Higher values, are higher power. Be careful not to go too high
+  #define E1_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+  #define E1_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+
+  //#define E2_IS_L6470
+  #define E2_MICROSTEPS 16     //number of microsteps
+  #define E2_K_VAL 50          // 0 - 255, Higher values, are higher power. Be careful not to go too high
+  #define E2_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+  #define E2_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+
+  //#define E3_IS_L6470
+  #define E3_MICROSTEPS 16     //number of microsteps
+  #define E3_K_VAL 50          // 0 - 255, Higher values, are higher power. Be careful not to go too high
+  #define E3_OVERCURRENT 2000  //maxc current in mA. If the current goes over this value, the driver will switch off
+  #define E3_STALLCURRENT 1500 //current in mA where the driver will detect a stall
+
+#endif
+
+/**
+ * TWI/I2C BUS
+ *
+ * This feature is an EXPERIMENTAL feature so it shall not be used on production
+ * machines. Enabling this will allow you to send and receive I2C data from slave
+ * devices on the bus.
+ *
+ * ; Example #1
+ * ; This macro send the string "Marlin" to the slave device with address 0x63 (99)
+ * ; It uses multiple M155 commands with one B<base 10> arg
+ * M155 A99  ; Target slave address
+ * M155 B77  ; M
+ * M155 B97  ; a
+ * M155 B114 ; r
+ * M155 B108 ; l
+ * M155 B105 ; i
+ * M155 B110 ; n
+ * M155 S1   ; Send the current buffer
+ *
+ * ; Example #2
+ * ; Request 6 bytes from slave device with address 0x63 (99)
+ * M156 A99 B5
+ *
+ * ; Example #3
+ * ; Example serial output of a M156 request
+ * echo:i2c-reply: from:99 bytes:5 data:hello
+ */
+
+// @section i2cbus
+
+//#define EXPERIMENTAL_I2CBUS
+
+#include "Conditionals.h"
+#include "SanityCheck.h"
+
+#endif //CONFIGURATION_ADV_H
diff --git a/Marlin/example_configurations/K8400/Dual Heads/Configuration.h b/Marlin/example_configurations/K8400/Dual Heads/Configuration.h
new file mode 100644
index 0000000000..c244ea0432
--- /dev/null
+++ b/Marlin/example_configurations/K8400/Dual Heads/Configuration.h	
@@ -0,0 +1,1216 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Configuration.h
+ *
+ * Basic settings such as:
+ *
+ * - Type of electronics
+ * - Type of temperature sensor
+ * - Printer geometry
+ * - Endstop configuration
+ * - LCD controller
+ * - Extra features
+ *
+ * Advanced settings can be found in Configuration_adv.h
+ *
+ */
+#ifndef CONFIGURATION_H
+#define CONFIGURATION_H
+
+/**
+ *
+ *  ***********************************
+ *  **  ATTENTION TO ALL DEVELOPERS  **
+ *  ***********************************
+ *
+ * You must increment this version number for every significant change such as,
+ * but not limited to: ADD, DELETE RENAME OR REPURPOSE any directive/option.
+ *
+ * Note: Update also Version.h !
+ */
+#define CONFIGURATION_H_VERSION 010100
+
+#include "boards.h"
+#include "macros.h"
+
+//===========================================================================
+//============================= Getting Started =============================
+//===========================================================================
+
+/**
+ * Here are some standard links for getting your machine calibrated:
+ *
+ * http://reprap.org/wiki/Calibration
+ * http://youtu.be/wAL9d7FgInk
+ * http://calculator.josefprusa.cz
+ * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
+ * http://www.thingiverse.com/thing:5573
+ * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
+ * http://www.thingiverse.com/thing:298812
+ */
+
+//===========================================================================
+//============================= DELTA Printer ===============================
+//===========================================================================
+// For a Delta printer replace the configuration files with the files in the
+// example_configurations/delta directory.
+//
+
+//===========================================================================
+//============================= SCARA Printer ===============================
+//===========================================================================
+// For a Scara printer replace the configuration files with the files in the
+// example_configurations/SCARA directory.
+//
+
+// @section info
+
+#if ENABLED(USE_AUTOMATIC_VERSIONING)
+  #include "_Version.h"
+#else
+  #include "Version.h"
+#endif
+
+// User-specified version info of this build to display in [Pronterface, etc] terminal window during
+// startup. Implementation of an idea by Prof Braino to inform user that any changes made to this
+// build by the user have been successfully uploaded into firmware.
+#define STRING_CONFIG_H_AUTHOR "(Anthony Birkett, default config)" // Who made the changes.
+#define SHOW_BOOTSCREEN
+#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1
+//#define STRING_SPLASH_LINE2 STRING_DISTRIBUTION_DATE // will be shown during bootup in line 2
+
+// @section machine
+
+// SERIAL_PORT selects which serial port should be used for communication with the host.
+// This allows the connection of wireless adapters (for instance) to non-default port pins.
+// Serial port 0 is still used by the Arduino bootloader regardless of this setting.
+// :[0,1,2,3,4,5,6,7]
+#define SERIAL_PORT 0
+
+// This determines the communication speed of the printer
+// :[2400,9600,19200,38400,57600,115200,250000]
+#define BAUDRATE 250000
+
+// Enable the Bluetooth serial interface on AT90USB devices
+//#define BLUETOOTH
+
+// The following define selects which electronics board you have.
+// Please choose the name from boards.h that matches your setup
+#ifndef MOTHERBOARD
+  #define MOTHERBOARD BOARD_K8400
+#endif
+
+// Optional custom name for your RepStrap or other custom machine
+// Displayed in the LCD "Ready" message
+//#define CUSTOM_MACHINE_NAME "3D Printer"
+
+// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines)
+// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
+//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
+
+// This defines the number of extruders
+// :[1,2,3,4]
+#define EXTRUDERS 2
+
+// For Cyclops or any "multi-extruder" that shares a single nozzle.
+//#define SINGLENOZZLE
+
+// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
+// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
+// For the other hotends it is their distance from the extruder 0 hotend.
+//#define HOTEND_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
+//#define HOTEND_OFFSET_Y {0.0, 5.00}  // (in mm) for each extruder, offset of the hotend on the Y axis
+
+//// The following define selects which power supply you have. Please choose the one that matches your setup
+// 1 = ATX
+// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
+// :{1:'ATX',2:'X-Box 360'}
+
+#define POWER_SUPPLY 1
+
+// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it.
+//#define PS_DEFAULT_OFF
+
+// @section temperature
+
+//===========================================================================
+//============================= Thermal Settings ============================
+//===========================================================================
+//
+//--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
+//
+//// Temperature sensor settings:
+// -3 is thermocouple with MAX31855 (only for sensor 0)
+// -2 is thermocouple with MAX6675 (only for sensor 0)
+// -1 is thermocouple with AD595
+// 0 is not used
+// 1 is 100k thermistor - best choice for EPCOS 100k (4.7k pullup)
+// 2 is 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
+// 3 is Mendel-parts thermistor (4.7k pullup)
+// 4 is 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
+// 5 is 100K thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (4.7k pullup)
+// 6 is 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup)
+// 7 is 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup)
+// 71 is 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup)
+// 8 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup)
+// 9 is 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup)
+// 10 is 100k RS thermistor 198-961 (4.7k pullup)
+// 11 is 100k beta 3950 1% thermistor (4.7k pullup)
+// 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
+// 13 is 100k Hisens 3950  1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
+// 20 is the PT100 circuit found in the Ultimainboard V2.x
+// 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
+// 70 is the 100K thermistor found in the bq Hephestos 2
+//
+//    1k ohm pullup tables - This is not normal, you would have to have changed out your 4.7k for 1k
+//                          (but gives greater accuracy and more stable PID)
+// 51 is 100k thermistor - EPCOS (1k pullup)
+// 52 is 200k thermistor - ATC Semitec 204GT-2 (1k pullup)
+// 55 is 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup)
+//
+// 1047 is Pt1000 with 4k7 pullup
+// 1010 is Pt1000 with 1k pullup (non standard)
+// 147 is Pt100 with 4k7 pullup
+// 110 is Pt100 with 1k pullup (non standard)
+// 998 and 999 are Dummy Tables. They will ALWAYS read 25°C or the temperature defined below.
+//     Use it for Testing or Development purposes. NEVER for production machine.
+//#define DUMMY_THERMISTOR_998_VALUE 25
+//#define DUMMY_THERMISTOR_999_VALUE 100
+// :{ '0': "Not used", '4': "10k !! do not use for a hotend. Bad resolution at high temp. !!", '1': "100k / 4.7k - EPCOS", '51': "100k / 1k - EPCOS", '6': "100k / 4.7k EPCOS - Not as accurate as Table 1", '5': "100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '7': "100k / 4.7k Honeywell 135-104LAG-J01", '71': "100k / 4.7k Honeywell 135-104LAF-J01", '8': "100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9': "100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10': "100k / 4.7k RS 198-961", '11': "100k / 4.7k beta 3950 1%", '12': "100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13': "100k Hisens 3950  1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '60': "100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '55': "100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '2': "200k / 4.7k - ATC Semitec 204GT-2", '52': "200k / 1k - ATC Semitec 204GT-2", '-3': "Thermocouple + MAX31855 (only for sensor 0)", '-2': "Thermocouple + MAX6675 (only for sensor 0)", '-1': "Thermocouple + AD595", '3': "Mendel-parts / 4.7k", '1047': "Pt1000 / 4.7k", '1010': "Pt1000 / 1k (non standard)", '20': "PT100 (Ultimainboard V2.x)", '147': "Pt100 / 4.7k", '110': "Pt100 / 1k (non-standard)", '998': "Dummy 1", '999': "Dummy 2" }
+#define TEMP_SENSOR_0 5
+#define TEMP_SENSOR_1 5
+#define TEMP_SENSOR_2 0
+#define TEMP_SENSOR_3 0
+#define TEMP_SENSOR_BED 0
+
+// This makes temp sensor 1 a redundant sensor for sensor 0. If the temperatures difference between these sensors is to high the print will be aborted.
+//#define TEMP_SENSOR_1_AS_REDUNDANT
+#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
+
+// Extruder temperature must be close to target for this long before M109 returns success
+#define TEMP_RESIDENCY_TIME 2   // (seconds)
+#define TEMP_HYSTERESIS 5       // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
+
+// Bed temperature must be close to target for this long before M190 returns success
+#define TEMP_BED_RESIDENCY_TIME 10  // (seconds)
+#define TEMP_BED_HYSTERESIS 3       // (degC) range of +/- temperatures considered "close" to the target one
+#define TEMP_BED_WINDOW     1       // (degC) Window around target to start the residency timer x degC early.
+
+// The minimal temperature defines the temperature below which the heater will not be enabled It is used
+// to check that the wiring to the thermistor is not broken.
+// Otherwise this would lead to the heater being powered on all the time.
+#define HEATER_0_MINTEMP 5
+#define HEATER_1_MINTEMP 5
+#define HEATER_2_MINTEMP 5
+#define HEATER_3_MINTEMP 5
+#define BED_MINTEMP 5
+
+// When temperature exceeds max temp, your heater will be switched off.
+// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!
+// You should use MINTEMP for thermistor short/failure protection.
+#define HEATER_0_MAXTEMP 275
+#define HEATER_1_MAXTEMP 275
+#define HEATER_2_MAXTEMP 275
+#define HEATER_3_MAXTEMP 275
+#define BED_MAXTEMP 150
+
+// If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS
+//#define HOTEND_WATTS (12.0*12.0/6.7) // P=U^2/R
+//#define BED_WATTS (12.0*12.0/1.1)    // P=U^2/R
+
+//===========================================================================
+//============================= PID Settings ================================
+//===========================================================================
+// PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning
+
+// Comment the following line to disable PID and enable bang-bang.
+#define PIDTEMP
+#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
+#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
+#if ENABLED(PIDTEMP)
+  //#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
+  //#define PID_DEBUG // Sends debug data to the serial port.
+  //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
+  //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
+  //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
+                                  // Set/get with gcode: M301 E[extruder number, 0-2]
+  #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
+                                  // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
+  #define PID_INTEGRAL_DRIVE_MAX PID_MAX  //limit for the integral term
+  #define K1 0.95 //smoothing factor within the PID
+
+  // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
+  // Ultimaker
+  //#define  DEFAULT_Kp 22.2
+  //#define  DEFAULT_Ki 1.08
+  //#define  DEFAULT_Kd 114
+
+  // MakerGear
+  //#define  DEFAULT_Kp 7.0
+  //#define  DEFAULT_Ki 0.1
+  //#define  DEFAULT_Kd 12
+
+  // Mendel Parts V9 on 12V
+  #define  DEFAULT_Kp 63.0
+  #define  DEFAULT_Ki 2.25
+  #define  DEFAULT_Kd 440
+
+#endif // PIDTEMP
+
+//===========================================================================
+//============================= PID > Bed Temperature Control ===============
+//===========================================================================
+// Select PID or bang-bang with PIDTEMPBED. If bang-bang, BED_LIMIT_SWITCHING will enable hysteresis
+//
+// Uncomment this to enable PID on the bed. It uses the same frequency PWM as the extruder.
+// If your PID_dT is the default, and correct for your hardware/configuration, that means 7.689Hz,
+// which is fine for driving a square wave into a resistive load and does not significantly impact you FET heating.
+// This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W heater.
+// If your configuration is significantly different than this and you don't understand the issues involved, you probably
+// shouldn't use bed PID until someone else verifies your hardware works.
+// If this is enabled, find your own PID constants below.
+//#define PIDTEMPBED
+
+//#define BED_LIMIT_SWITCHING
+
+// This sets the max power delivered to the bed, and replaces the HEATER_BED_DUTY_CYCLE_DIVIDER option.
+// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
+// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
+// so you shouldn't use it unless you are OK with PWM on your bed.  (see the comment on enabling PIDTEMPBED)
+#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
+
+#if ENABLED(PIDTEMPBED)
+
+  //#define PID_BED_DEBUG // Sends debug data to the serial port.
+
+  #define PID_BED_INTEGRAL_DRIVE_MAX MAX_BED_POWER //limit for the integral term
+
+  //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
+  //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
+  #define  DEFAULT_bedKp 10.00
+  #define  DEFAULT_bedKi .023
+  #define  DEFAULT_bedKd 305.4
+
+  //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
+  //from pidautotune
+  //#define  DEFAULT_bedKp 97.1
+  //#define  DEFAULT_bedKi 1.41
+  //#define  DEFAULT_bedKd 1675.16
+
+  // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
+#endif // PIDTEMPBED
+
+// @section extruder
+
+//this prevents dangerous Extruder moves, i.e. if the temperature is under the limit
+//can be software-disabled for whatever purposes by
+#define PREVENT_DANGEROUS_EXTRUDE
+//if PREVENT_DANGEROUS_EXTRUDE is on, you can still disable (uncomment) very long bits of extrusion separately.
+#define PREVENT_LENGTHY_EXTRUDE
+
+#define EXTRUDE_MINTEMP 160
+#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
+
+//===========================================================================
+//======================== Thermal Runaway Protection =======================
+//===========================================================================
+
+/**
+ * Thermal Protection protects your printer from damage and fire if a
+ * thermistor falls out or temperature sensors fail in any way.
+ *
+ * The issue: If a thermistor falls out or a temperature sensor fails,
+ * Marlin can no longer sense the actual temperature. Since a disconnected
+ * thermistor reads as a low temperature, the firmware will keep the heater on.
+ *
+ * If you get "Thermal Runaway" or "Heating failed" errors the
+ * details can be tuned in Configuration_adv.h
+ */
+
+#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
+#define THERMAL_PROTECTION_BED     // Enable thermal protection for the heated bed
+
+//===========================================================================
+//============================= Mechanical Settings =========================
+//===========================================================================
+
+// @section machine
+
+// Uncomment one of these options to enable CoreXY, CoreXZ, or CoreYZ kinematics
+//#define COREXY
+//#define COREXZ
+//#define COREYZ
+
+// Enable this option for Toshiba steppers
+//#define CONFIG_STEPPERS_TOSHIBA
+
+//===========================================================================
+//============================== Endstop Settings ===========================
+//===========================================================================
+
+// @section homing
+
+// Specify here all the endstop connectors that are connected to any endstop or probe.
+// Almost all printers will be using one per axis. Probes will use one or more of the
+// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
+#define USE_XMIN_PLUG
+#define USE_YMIN_PLUG
+#define USE_ZMIN_PLUG
+//#define USE_XMAX_PLUG
+//#define USE_YMAX_PLUG
+//#define USE_ZMAX_PLUG
+
+// coarse Endstop Settings
+#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
+
+#if DISABLED(ENDSTOPPULLUPS)
+  // fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined
+  //#define ENDSTOPPULLUP_XMAX
+  //#define ENDSTOPPULLUP_YMAX
+  //#define ENDSTOPPULLUP_ZMAX
+  //#define ENDSTOPPULLUP_XMIN
+  //#define ENDSTOPPULLUP_YMIN
+  //#define ENDSTOPPULLUP_ZMIN
+  //#define ENDSTOPPULLUP_ZMIN_PROBE
+#endif
+
+// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
+const bool X_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
+const bool Y_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
+const bool Z_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
+const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
+const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
+const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
+const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop.
+
+//===========================================================================
+//============================= Z Probe Options =============================
+//===========================================================================
+
+//
+// Probe Type
+// Probes are sensors/switches that are activated / deactivated before/after use.
+//
+// Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc.
+// You must activate one of these to use AUTO_BED_LEVELING_FEATURE below.
+//
+// Use M851 to set the Z probe vertical offset from the nozzle. Store with M500.
+//
+
+// A Fix-Mounted Probe either doesn't deploy or needs manual deployment.
+// For example an inductive probe, or a setup that uses the nozzle to probe.
+// An inductive probe must be deactivated to go below
+// its trigger-point if hardware endstops are active.
+//#define FIX_MOUNTED_PROBE
+
+// Z Servo Probe, such as an endstop switch on a rotating arm.
+//#define Z_ENDSTOP_SERVO_NR 0
+//#define Z_SERVO_ANGLES {70,0} // Z Servo Deploy and Stow angles
+
+// Enable if you have a Z probe mounted on a sled like those designed by Charles Bell.
+//#define Z_PROBE_SLED
+//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
+
+// Z Probe to nozzle (X,Y) offset, relative to (0, 0).
+// X and Y offsets must be integers.
+//
+// In the following example the X and Y offsets are both positive:
+// #define X_PROBE_OFFSET_FROM_EXTRUDER 10
+// #define Y_PROBE_OFFSET_FROM_EXTRUDER 10
+//
+//    +-- BACK ---+
+//    |           |
+//  L |    (+) P  | R <-- probe (20,20)
+//  E |           | I
+//  F | (-) N (+) | G <-- nozzle (10,10)
+//  T |           | H
+//    |    (-)    | T
+//    |           |
+//    O-- FRONT --+
+//  (0,0)
+#define X_PROBE_OFFSET_FROM_EXTRUDER 10  // X offset: -left  +right  [of the nozzle]
+#define Y_PROBE_OFFSET_FROM_EXTRUDER 10  // Y offset: -front +behind [the nozzle]
+#define Z_PROBE_OFFSET_FROM_EXTRUDER 0   // Z offset: -below +above  [the nozzle]
+
+// X and Y axis travel speed (mm/m) between probes
+#define XY_PROBE_SPEED 8000
+
+//
+// Allen Key Probe is defined in the Delta example configurations.
+//
+
+// Enable Z_MIN_PROBE_ENDSTOP to use _both_ a Z Probe and a Z-min-endstop on the same machine.
+// With this option the Z_MIN_PROBE_PIN will only be used for probing, never for homing.
+//
+// *** PLEASE READ ALL INSTRUCTIONS BELOW FOR SAFETY! ***
+//
+// To continue using the Z-min-endstop for homing, be sure to disable Z_SAFE_HOMING.
+// Example: To park the head outside the bed area when homing with G28.
+//
+// To use a separate Z probe, your board must define a Z_MIN_PROBE_PIN.
+//
+// For a servo-based Z probe, you must set up servo support below, including
+// NUM_SERVOS, Z_ENDSTOP_SERVO_NR and Z_SERVO_ANGLES.
+//
+// - RAMPS 1.3/1.4 boards may be able to use the 5V, GND, and Aux4->D32 pin.
+// - Use 5V for powered (usu. inductive) sensors.
+// - Otherwise connect:
+//   - normally-closed switches to GND and D32.
+//   - normally-open switches to 5V and D32.
+//
+// Normally-closed switches are advised and are the default.
+//
+// The Z_MIN_PROBE_PIN sets the Arduino pin to use. (See your board's pins file.)
+// Since the RAMPS Aux4->D32 pin maps directly to the Arduino D32 pin, D32 is the
+// default pin for all RAMPS-based boards. Some other boards map differently.
+// To set or change the pin for your board, edit the appropriate pins_XXXXX.h file.
+//
+// WARNING:
+// Setting the wrong pin may have unexpected and potentially disastrous consequences.
+// Use with caution and do your homework.
+//
+//#define Z_MIN_PROBE_ENDSTOP
+
+// Enable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to use the Z_MIN_PIN for your Z_MIN_PROBE.
+// The Z_MIN_PIN will then be used for both Z-homing and probing.
+#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
+
+// To use a probe you must enable one of the two options above!
+
+// This option disables the use of the Z_MIN_PROBE_PIN
+// To enable the Z probe pin but disable its use, uncomment the line below. This only affects a
+// Z probe switch if you have a separate Z min endstop also and have activated Z_MIN_PROBE_ENDSTOP above.
+// If you're using the Z MIN endstop connector for your Z probe, this has no effect.
+//#define DISABLE_Z_MIN_PROBE_ENDSTOP
+
+// Enable Z Probe Repeatability test to see how accurate your probe is
+//#define Z_MIN_PROBE_REPEATABILITY_TEST
+
+//
+// Probe Raise options provide clearance for the probe to deploy, stow, and travel.
+//
+#define Z_RAISE_PROBE_DEPLOY_STOW 15 // Raise to make room for the probe to deploy / stow
+#define Z_RAISE_BETWEEN_PROBINGS 5  // Raise between probing points.
+
+//
+// For M851 give a range for adjusting the Z probe offset
+//
+#define Z_PROBE_OFFSET_RANGE_MIN -20
+#define Z_PROBE_OFFSET_RANGE_MAX 20
+
+// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
+// :{0:'Low',1:'High'}
+#define X_ENABLE_ON 0
+#define Y_ENABLE_ON 0
+#define Z_ENABLE_ON 0
+#define E_ENABLE_ON 0 // For all extruders
+
+// Disables axis stepper immediately when it's not being used.
+// WARNING: When motors turn off there is a chance of losing position accuracy!
+#define DISABLE_X false
+#define DISABLE_Y false
+#define DISABLE_Z false
+// Warn on display about possibly reduced accuracy
+//#define DISABLE_REDUCED_ACCURACY_WARNING
+
+// @section extruder
+
+#define DISABLE_E false // For all extruders
+#define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled
+
+// @section machine
+
+// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
+#define INVERT_X_DIR false
+#define INVERT_Y_DIR true
+#define INVERT_Z_DIR true
+
+// @section extruder
+
+// For direct drive extruder v9 set to true, for geared extruder set to false.
+#define INVERT_E0_DIR false
+#define INVERT_E1_DIR true
+#define INVERT_E2_DIR false
+#define INVERT_E3_DIR false
+
+// @section homing
+//#define MIN_Z_HEIGHT_FOR_HOMING 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+                                    // Be sure you have this distance over your Z_MAX_POS in case.
+
+// ENDSTOP SETTINGS:
+// Sets direction of endstops when homing; 1=MAX, -1=MIN
+// :[-1,1]
+#define X_HOME_DIR -1
+#define Y_HOME_DIR -1
+#define Z_HOME_DIR -1
+
+#define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
+#define max_software_endstops true  // If true, axis won't move to coordinates greater than the defined lengths below.
+
+// @section machine
+
+// Travel limits after homing (units are in mm)
+#define X_MIN_POS 0
+#define Y_MIN_POS 20
+#define Z_MIN_POS 0
+#define X_MAX_POS 200
+#define Y_MAX_POS 200
+#define Z_MAX_POS 190
+
+//===========================================================================
+//========================= Filament Runout Sensor ==========================
+//===========================================================================
+//#define FILAMENT_RUNOUT_SENSOR // Uncomment for defining a filament runout sensor such as a mechanical or opto endstop to check the existence of filament
+                                 // In RAMPS uses servo pin 2. Can be changed in pins file. For other boards pin definition should be made.
+                                 // It is assumed that when logic high = filament available
+                                 //                    when logic  low = filament ran out
+#if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  const bool FIL_RUNOUT_INVERTING = false; // set to true to invert the logic of the sensor.
+  #define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
+  #define FILAMENT_RUNOUT_SCRIPT "M600"
+#endif
+
+//===========================================================================
+//============================ Mesh Bed Leveling ============================
+//===========================================================================
+
+//#define MESH_BED_LEVELING    // Enable mesh bed leveling.
+
+#if ENABLED(MESH_BED_LEVELING)
+  #define MESH_INSET 10        // Mesh inset margin on print area
+  #define MESH_NUM_X_POINTS 3  // Don't use more than 7 points per axis, implementation limited.
+  #define MESH_NUM_Y_POINTS 3
+  #define MESH_HOME_SEARCH_Z 4  // Z after Home, bed somewhere below but above 0.0.
+
+  //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest at origin [0,0,0]
+
+  //#define MANUAL_BED_LEVELING  // Add display menu option for bed leveling.
+
+  #if ENABLED(MANUAL_BED_LEVELING)
+    #define MBL_Z_STEP 0.025  // Step size while manually probing Z axis.
+  #endif  // MANUAL_BED_LEVELING
+
+#endif  // MESH_BED_LEVELING
+
+//===========================================================================
+//============================ Bed Auto Leveling ============================
+//===========================================================================
+
+// @section bedlevel
+
+//#define AUTO_BED_LEVELING_FEATURE // Delete the comment to enable (remove // at the start of the line)
+//#define DEBUG_LEVELING_FEATURE
+
+#if ENABLED(AUTO_BED_LEVELING_FEATURE)
+
+  // There are 2 different ways to specify probing locations:
+  //
+  // - "grid" mode
+  //   Probe several points in a rectangular grid.
+  //   You specify the rectangle and the density of sample points.
+  //   This mode is preferred because there are more measurements.
+  //
+  // - "3-point" mode
+  //   Probe 3 arbitrary points on the bed (that aren't collinear)
+  //   You specify the XY coordinates of all 3 points.
+
+  // Enable this to sample the bed in a grid (least squares solution).
+  // Note: this feature generates 10KB extra code size.
+  #define AUTO_BED_LEVELING_GRID
+
+  #if ENABLED(AUTO_BED_LEVELING_GRID)
+
+    #define LEFT_PROBE_BED_POSITION 15
+    #define RIGHT_PROBE_BED_POSITION 170
+    #define FRONT_PROBE_BED_POSITION 20
+    #define BACK_PROBE_BED_POSITION 170
+
+    #define MIN_PROBE_EDGE 10 // The Z probe minimum square sides can be no smaller than this.
+
+    // Set the number of grid points per dimension.
+    // You probably don't need more than 3 (squared=9).
+    #define AUTO_BED_LEVELING_GRID_POINTS 2
+
+  #else  // !AUTO_BED_LEVELING_GRID
+
+    // Arbitrary points to probe.
+    // A simple cross-product is used to estimate the plane of the bed.
+    #define ABL_PROBE_PT_1_X 15
+    #define ABL_PROBE_PT_1_Y 180
+    #define ABL_PROBE_PT_2_X 15
+    #define ABL_PROBE_PT_2_Y 20
+    #define ABL_PROBE_PT_3_X 170
+    #define ABL_PROBE_PT_3_Y 20
+
+  #endif // !AUTO_BED_LEVELING_GRID
+
+  //#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" // These commands will be executed in the end of G29 routine.
+                                                                             // Useful to retract a deployable Z probe.
+
+  // If you've enabled AUTO_BED_LEVELING_FEATURE and are using the Z Probe for Z Homing,
+  // it is highly recommended you also enable Z_SAFE_HOMING below!
+
+#endif // AUTO_BED_LEVELING_FEATURE
+
+
+// @section homing
+
+// The position of the homing switches
+//#define MANUAL_HOME_POSITIONS  // If defined, MANUAL_*_HOME_POS below will be used
+//#define BED_CENTER_AT_0_0  // If defined, the center of the bed is at (X=0, Y=0)
+
+// Manual homing switch locations:
+// For deltabots this means top and center of the Cartesian print volume.
+#if ENABLED(MANUAL_HOME_POSITIONS)
+  #define MANUAL_X_HOME_POS 0
+  #define MANUAL_Y_HOME_POS 0
+  #define MANUAL_Z_HOME_POS 0
+  //#define MANUAL_Z_HOME_POS 402 // For delta: Distance between nozzle and print surface after homing.
+#endif
+
+// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
+//
+// With this feature enabled:
+//
+// - Allow Z homing only after X and Y homing AND stepper drivers still enabled.
+// - If stepper drivers time out, it will need X and Y homing again before Z homing.
+// - Position the Z probe in a defined XY point before Z Homing when homing all axes (G28).
+// - Prevent Z homing when the Z probe is outside bed area.
+//#define Z_SAFE_HOMING
+
+#if ENABLED(Z_SAFE_HOMING)
+  #define Z_SAFE_HOMING_X_POINT ((X_MIN_POS + X_MAX_POS) / 2)    // X point for Z homing when homing all axis (G28).
+  #define Z_SAFE_HOMING_Y_POINT ((Y_MIN_POS + Y_MAX_POS) / 2)    // Y point for Z homing when homing all axis (G28).
+#endif
+
+
+// @section motion
+
+/**
+ * MOVEMENT SETTINGS
+ */
+
+#define HOMING_FEEDRATE {50*60, 50*60, 8*60, 0}  // set the homing speeds (mm/min)
+
+// default settings
+
+#define DEFAULT_AXIS_STEPS_PER_UNIT   {134.74,134.74,4266.66,148.7}  // default steps per unit for Ultimaker
+#define DEFAULT_MAX_FEEDRATE          {160, 160, 10, 10000}    // (mm/sec)
+#define DEFAULT_MAX_ACCELERATION      {9000,9000,100,10000}    // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
+
+#define DEFAULT_ACCELERATION          6000    // X, Y, Z and E acceleration in mm/s^2 for printing moves
+#define DEFAULT_RETRACT_ACCELERATION  6000    // E acceleration in mm/s^2 for retracts
+#define DEFAULT_TRAVEL_ACCELERATION   3000    // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves
+
+// The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously)
+#define DEFAULT_XYJERK                10.0    // (mm/sec)
+#define DEFAULT_ZJERK                 0.5     // (mm/sec)
+#define DEFAULT_EJERK                 20.0    // (mm/sec)
+
+
+//=============================================================================
+//============================= Additional Features ===========================
+//=============================================================================
+
+// @section extras
+
+//
+// EEPROM
+//
+// The microcontroller can store settings in the EEPROM, e.g. max velocity...
+// M500 - stores parameters in EEPROM
+// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
+// M502 - reverts to the default "factory settings".  You still need to store them in EEPROM afterwards if you want to.
+//define this to enable EEPROM support
+#define EEPROM_SETTINGS
+
+#if ENABLED(EEPROM_SETTINGS)
+  // To disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out:
+  #define EEPROM_CHITCHAT // Please keep turned on if you can.
+#endif
+
+//
+// Host Keepalive
+//
+// When enabled Marlin will send a busy status message to the host
+// every couple of seconds when it can't accept commands.
+//
+#define HOST_KEEPALIVE_FEATURE        // Disable this if your host doesn't like keepalive messages
+#define DEFAULT_KEEPALIVE_INTERVAL 2  // Number of seconds between "busy" messages. Set with M113.
+
+//
+// M100 Free Memory Watcher
+//
+//#define M100_FREE_MEMORY_WATCHER // uncomment to add the M100 Free Memory Watcher for debug purpose
+
+//
+// G20/G21 Inch mode support
+//
+//#define INCH_MODE_SUPPORT
+
+//
+// M149 Set temperature units support
+//
+//#define TEMPERATURE_UNITS_SUPPORT
+
+// @section temperature
+
+// Preheat Constants
+#define PLA_PREHEAT_HOTEND_TEMP 210
+#define PLA_PREHEAT_HPB_TEMP 0
+#define PLA_PREHEAT_FAN_SPEED 165   // Insert Value between 0 and 255
+
+#define ABS_PREHEAT_HOTEND_TEMP 245
+#define ABS_PREHEAT_HPB_TEMP 0
+#define ABS_PREHEAT_FAN_SPEED 165   // Insert Value between 0 and 255
+
+//
+// Print job timer
+//
+// Enable this option to automatically start and stop the
+// print job timer when M104 and M109 commands are received.
+//
+// In all cases the timer can be started and stopped using
+// the following commands:
+//
+// - M75  - Start the print job timer
+// - M76  - Pause the print job timer
+// - M77  - Stop the print job timer
+#define PRINTJOB_TIMER_AUTOSTART
+
+//
+// Print Counter
+//
+// When enabled Marlin will keep track of some print statistical data such as:
+//  - Total print jobs
+//  - Total successful print jobs
+//  - Total failed print jobs
+//  - Total time printing
+//
+// This information can be viewed by the M78 command.
+//#define PRINTCOUNTER
+
+//=============================================================================
+//============================= LCD and SD support ============================
+//=============================================================================
+
+// @section lcd
+
+//
+// LCD LANGUAGE
+//
+// Here you may choose the language used by Marlin on the LCD menus, the following
+// list of languages are available:
+//    en, an, bg, ca, cn, cz, de, es, eu, fi, fr, gl, hr, it, kana,
+//    kana_utf8, nl, pl, pt, pt_utf8, pt-br, pt-br_utf8, ru, test
+//
+// :{'en':'English','an':'Aragonese','bg':'Bulgarian','ca':'Catalan','cn':'Chinese','cz':'Czech','de':'German','es':'Spanish','eu':'Basque-Euskera','fi':'Finnish','fr':'French','gl':'Galician','hr':'Croatian','it':'Italian','kana':'Japanese','kana_utf8':'Japanese (UTF8)','nl':'Dutch','pl':'Polish','pt':'Portuguese','pt-br':'Portuguese (Brazilian)','pt-br_utf8':'Portuguese (Brazilian UTF8)','pt_utf8':'Portuguese (UTF8)','ru':'Russian','test':'TEST'}
+//
+#define LCD_LANGUAGE en
+
+//
+// LCD Character Set
+//
+// Note: This option is NOT applicable to Graphical Displays.
+//
+// All character-based LCD's provide ASCII plus one of these
+// language extensions:
+//
+//  - JAPANESE ... the most common
+//  - WESTERN  ... with more accented characters
+//  - CYRILLIC ... for the Russian language
+//
+// To determine the language extension installed on your controller:
+//
+//  - Compile and upload with LCD_LANGUAGE set to 'test'
+//  - Click the controller to view the LCD menu
+//  - The LCD will display Japanese, Western, or Cyrillic text
+//
+// See https://github.com/MarlinFirmware/Marlin/wiki/LCD-Language
+//
+// :['JAPANESE','WESTERN','CYRILLIC']
+//
+#define DISPLAY_CHARSET_HD44780 JAPANESE
+
+//
+// LCD TYPE
+//
+// You may choose ULTRA_LCD if you have character based LCD with 16x2, 16x4, 20x2,
+// 20x4 char/lines or DOGLCD for the full graphics display with 128x64 pixels
+// (ST7565R family). (This option will be set automatically for certain displays.)
+//
+// IMPORTANT NOTE: The U8glib library is required for Full Graphic Display!
+//                 https://github.com/olikraus/U8glib_Arduino
+//
+#define ULTRA_LCD   // Character based
+//#define DOGLCD      // Full graphics display
+
+//
+// SD CARD
+//
+// SD Card support is disabled by default. If your controller has an SD slot,
+// you must uncomment the following option or it won't work.
+//
+#define SDSUPPORT
+
+//
+// SD CARD: SPI SPEED
+//
+// Uncomment ONE of the following items to use a slower SPI transfer
+// speed. This is usually required if you're getting volume init errors.
+//
+//#define SPI_SPEED SPI_HALF_SPEED
+//#define SPI_SPEED SPI_QUARTER_SPEED
+//#define SPI_SPEED SPI_EIGHTH_SPEED
+
+//
+// SD CARD: ENABLE CRC
+//
+// Use CRC checks and retries on the SD communication.
+//
+//#define SD_CHECK_AND_RETRY
+
+//
+// ENCODER SETTINGS
+//
+// This option overrides the default number of encoder pulses needed to
+// produce one step. Should be increased for high-resolution encoders.
+//
+#define ENCODER_PULSES_PER_STEP 4
+
+//
+// Use this option to override the number of step signals required to
+// move between next/prev menu items.
+//
+#define ENCODER_STEPS_PER_MENU_ITEM 1
+
+/**
+ * Encoder Direction Options
+ *
+ * Test your encoder's behavior first with both options disabled.
+ *
+ *  Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION.
+ *  Reversed Menu Navigation only?    Enable REVERSE_MENU_DIRECTION.
+ *  Reversed Value Editing only?      Enable BOTH options.
+ */
+
+//
+// This option reverses the encoder direction everywhere
+//
+//  Set this option if CLOCKWISE causes values to DECREASE
+//
+//#define REVERSE_ENCODER_DIRECTION
+
+//
+// This option reverses the encoder direction for navigating LCD menus.
+//
+//  If CLOCKWISE normally moves DOWN this makes it go UP.
+//  If CLOCKWISE normally moves UP this makes it go DOWN.
+//
+#define REVERSE_MENU_DIRECTION
+
+//
+// Individual Axis Homing
+//
+// Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
+//
+//#define INDIVIDUAL_AXIS_HOMING_MENU
+
+//
+// SPEAKER/BUZZER
+//
+// If you have a speaker that can produce tones, enable it here.
+// By default Marlin assumes you have a buzzer with a fixed frequency.
+//
+//#define SPEAKER
+
+//
+// The duration and frequency for the UI feedback sound.
+// Set these to 0 to disable audio feedback in the LCD menus.
+//
+// Note: Test audio output with the G-Code:
+//  M300 S<frequency Hz> P<duration ms>
+//
+//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100
+//#define LCD_FEEDBACK_FREQUENCY_HZ 1000
+
+//
+// CONTROLLER TYPE: Standard
+//
+// Marlin supports a wide variety of controllers.
+// Enable one of the following options to specify your controller.
+//
+
+//
+// ULTIMAKER Controller.
+//
+#define ULTIMAKERCONTROLLER
+
+//
+// ULTIPANEL as seen on Thingiverse.
+//
+//#define ULTIPANEL
+
+//
+// Cartesio UI
+// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface
+//
+//#define CARTESIO_UI
+
+//
+// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
+// http://reprap.org/wiki/PanelOne
+//
+//#define PANEL_ONE
+
+//
+// MaKr3d Makr-Panel with graphic controller and SD support.
+// http://reprap.org/wiki/MaKr3d_MaKrPanel
+//
+//#define MAKRPANEL
+
+//
+// Activate one of these if you have a Panucatt Devices
+// Viki 2.0 or mini Viki with Graphic LCD
+// http://panucatt.com
+//
+//#define VIKI2
+//#define miniVIKI
+
+//
+// Adafruit ST7565 Full Graphic Controller.
+// https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/
+//
+//#define ELB_FULL_GRAPHIC_CONTROLLER
+
+//
+// RepRapDiscount Smart Controller.
+// http://reprap.org/wiki/RepRapDiscount_Smart_Controller
+//
+// Note: Usually sold with a white PCB.
+//
+//#define REPRAP_DISCOUNT_SMART_CONTROLLER
+
+//
+// GADGETS3D G3D LCD/SD Controller
+// http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel
+//
+// Note: Usually sold with a blue PCB.
+//
+//#define G3D_PANEL
+
+//
+// RepRapDiscount FULL GRAPHIC Smart Controller
+// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
+//
+//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
+
+//
+// MakerLab Mini Panel with graphic
+// controller and SD support - http://reprap.org/wiki/Mini_panel
+//
+//#define MINIPANEL
+
+//
+// RepRapWorld REPRAPWORLD_KEYPAD v1.1
+// http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626
+//
+// REPRAPWORLD_KEYPAD_MOVE_STEP sets how much should the robot move when a key
+// is pressed, a value of 10.0 means 10mm per click.
+//
+//#define REPRAPWORLD_KEYPAD
+//#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0
+
+//
+// RigidBot Panel V1.0
+// http://www.inventapart.com/
+//
+//#define RIGIDBOT_PANEL
+
+//
+// BQ LCD Smart Controller shipped by
+// default with the BQ Hephestos 2 and Witbox 2.
+//
+//#define BQ_LCD_SMART_CONTROLLER
+
+//
+// CONTROLLER TYPE: I2C
+//
+// Note: These controllers require the installation of Arduino's LiquidCrystal_I2C
+// library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C
+//
+
+//
+// Elefu RA Board Control Panel
+// http://www.elefu.com/index.php?route=product/product&product_id=53
+//
+//#define RA_CONTROL_PANEL
+
+//
+// Sainsmart YW Robot (LCM1602) LCD Display
+//
+//#define LCD_I2C_SAINSMART_YWROBOT
+
+//
+// Generic LCM1602 LCD adapter
+//
+//#define LCM1602
+
+//
+// PANELOLU2 LCD with status LEDs,
+// separate encoder and click inputs.
+//
+// Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later.
+// For more info: https://github.com/lincomatic/LiquidTWI2
+//
+// Note: The PANELOLU2 encoder click input can either be directly connected to
+// a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1).
+//
+//#define LCD_I2C_PANELOLU2
+
+//
+// Panucatt VIKI LCD with status LEDs,
+// integrated click & L/R/U/D buttons, separate encoder inputs.
+//
+//#define LCD_I2C_VIKI
+
+//
+// SSD1306 OLED full graphics generic display
+//
+//#define U8GLIB_SSD1306
+
+//
+// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules
+//
+//#define SAV_3DGLCD
+#if ENABLED(SAV_3DGLCD)
+  //#define U8GLIB_SSD1306
+  #define U8GLIB_SH1106
+#endif
+
+//
+// CONTROLLER TYPE: Shift register panels
+//
+// 2 wire Non-latching LCD SR from https://goo.gl/aJJ4sH
+// LCD configuration: http://reprap.org/wiki/SAV_3D_LCD
+//
+//#define SAV_3DLCD
+
+//=============================================================================
+//=============================== Extra Features ==============================
+//=============================================================================
+
+// @section extras
+
+// Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino
+//#define FAST_PWM_FAN
+
+// Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
+// which is not as annoying as with the hardware PWM. On the other hand, if this frequency
+// is too low, you should also increment SOFT_PWM_SCALE.
+//#define FAN_SOFT_PWM
+
+// Incrementing this by 1 will double the software PWM frequency,
+// affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
+// However, control resolution will be halved for each increment;
+// at zero value, there are 128 effective control positions.
+#define SOFT_PWM_SCALE 0
+
+// Temperature status LEDs that display the hotend and bed temperature.
+// If all hotends and bed temperature and temperature setpoint are < 54C then the BLUE led is on.
+// Otherwise the RED led is on. There is 1C hysteresis.
+//#define TEMP_STAT_LEDS
+
+// M240  Triggers a camera by emulating a Canon RC-1 Remote
+// Data from: http://www.doc-diy.net/photo/rc-1_hacked/
+//#define PHOTOGRAPH_PIN     23
+
+// SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure
+//#define SF_ARC_FIX
+
+// Support for the BariCUDA Paste Extruder.
+//#define BARICUDA
+
+//define BlinkM/CyzRgb Support
+//#define BLINKM
+
+/*********************************************************************\
+* R/C SERVO support
+* Sponsored by TrinityLabs, Reworked by codexmas
+**********************************************************************/
+
+// Number of servos
+//
+// If you select a configuration below, this will receive a default value and does not need to be set manually
+// set it manually if you have more servos than extruders and wish to manually control some
+// leaving it undefined or defining as 0 will disable the servo subsystem
+// If unsure, leave commented / disabled
+//
+//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
+
+// Delay (in microseconds) before the next move will start, to give the servo time to reach its target angle.
+// 300ms is a good value but you can try less delay.
+// If the servo can't reach the requested position, increase it.
+#define SERVO_DELAY 300
+
+// Servo deactivation
+//
+// With this option servos are powered only during movement, then turned off to prevent jitter.
+//#define DEACTIVATE_SERVOS_AFTER_MOVE
+
+/**********************************************************************\
+ * Support for a filament diameter sensor
+ * Also allows adjustment of diameter at print time (vs  at slicing)
+ * Single extruder only at this point (extruder 0)
+ *
+ * Motherboards
+ * 34 - RAMPS1.4 - uses Analog input 5 on the AUX2 connector
+ * 81 - Printrboard - Uses Analog input 2 on the Exp1 connector (version B,C,D,E)
+ * 301 - Rambo  - uses Analog input 3
+ * Note may require analog pins to be defined for different motherboards
+ **********************************************************************/
+// Uncomment below to enable
+//#define FILAMENT_WIDTH_SENSOR
+
+#define DEFAULT_NOMINAL_FILAMENT_DIA 3.00  //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software.  Used for sensor reading validation
+
+#if ENABLED(FILAMENT_WIDTH_SENSOR)
+  #define FILAMENT_SENSOR_EXTRUDER_NUM 0   //The number of the extruder that has the filament sensor (0,1,2)
+  #define MEASUREMENT_DELAY_CM        14   //measurement delay in cm.  This is the distance from filament sensor to middle of barrel
+
+  #define MEASURED_UPPER_LIMIT         3.30  //upper limit factor used for sensor reading validation in mm
+  #define MEASURED_LOWER_LIMIT         1.90  //lower limit factor for sensor reading validation in mm
+  #define MAX_MEASUREMENT_DELAY       20     //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM  and lower number saves RAM)
+
+  #define DEFAULT_MEASURED_FILAMENT_DIA  DEFAULT_NOMINAL_FILAMENT_DIA  //set measured to nominal initially
+
+  //When using an LCD, uncomment the line below to display the Filament sensor data on the last line instead of status.  Status will appear for 5 sec.
+  //#define FILAMENT_LCD_DISPLAY
+#endif
+
+#include "Configuration_adv.h"
+#include "thermistortables.h"
+
+#endif //CONFIGURATION_H
diff --git a/Marlin/example_configurations/K8400/README.md b/Marlin/example_configurations/K8400/README.md
new file mode 100644
index 0000000000..c9089b5870
--- /dev/null
+++ b/Marlin/example_configurations/K8400/README.md
@@ -0,0 +1,15 @@
+# Configuration for Velleman K8400 Vertex
+http://www.k8400.eu/
+
+Configuration files for the K8400, ported upstream from the official Velleman firmware.
+Like it's predecessor, (K8200), the K8400 is a 3Drag clone. There are some minor differences, documented in pins_K8400.h.
+
+Single and dual head configurations provided. Copy the correct Configuration.h and Configuration_adv.h to the /Marlin/ directory.
+
+**NOTE: This configuration includes the community sourced feed rate fix. Use 100% feed rate in Repetier!**
+
+For implementation and updated K8400 firmware, see https://github.com/birkett/Velleman-K8400-Firmware
+
+### Original Sources
+Credit to Velleman for the original 1.0.x based code:<br />
+http://www.vertex3dprinter.eu/downloads/files/vertex/firmware/vertex-m1-v1.4-h2.zip
diff --git a/Marlin/pins.h b/Marlin/pins.h
index bbabe53be1..bd251216e1 100644
--- a/Marlin/pins.h
+++ b/Marlin/pins.h
@@ -77,6 +77,8 @@
   #include "pins_3DRAG.h"
 #elif MB(K8200)
   #include "pins_K8200.h"
+#elif MB(K8400)
+  #include "pins_K8400.h"
 #elif MB(TEENSYLU)
   #include "pins_TEENSYLU.h"
 #elif MB(RUMBA)
diff --git a/Marlin/pins_3DRAG.h b/Marlin/pins_3DRAG.h
index c04464b436..6f253ac8a3 100644
--- a/Marlin/pins_3DRAG.h
+++ b/Marlin/pins_3DRAG.h
@@ -21,7 +21,7 @@
  */
 
 /**
- * 3DRAG (and K8200) Arduino Mega with RAMPS v1.4 pin assignments
+ * 3DRAG (and K8200 / K8400) Arduino Mega with RAMPS v1.4 pin assignments
  */
 
 #ifndef BOARD_NAME
diff --git a/Marlin/pins_K8400.h b/Marlin/pins_K8400.h
new file mode 100644
index 0000000000..a15e9e4949
--- /dev/null
+++ b/Marlin/pins_K8400.h
@@ -0,0 +1,52 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Velleman K8400 (Vertex)
+ * 3DRAG clone
+ *
+ * K8400 has some minor differences over a normal 3Drag:
+ *  - No X/Y max endstops
+ *  - Second extruder step pin has moved
+ *  - No power supply control
+ *  - Second heater has moved pin
+ */
+
+#define BOARD_NAME              "K8400"
+#define DEFAULT_MACHINE_NAME    "Vertex"
+#define DEFAULT_SOURCE_CODE_URL "https://github.com/birkett/Vertex-K8400-Firmware"
+
+#include "pins_3DRAG.h"
+
+#undef  X_MAX_PIN
+#define X_MAX_PIN     -1
+#undef  Y_MAX_PIN
+#define Y_MAX_PIN     -1
+
+#undef E1_STEP_PIN
+#define E1_STEP_PIN   32
+
+#undef PS_ON_PIN
+#undef KILL_PIN
+
+#undef HEATER_1_PIN
+#define HEATER_1_PIN  11
diff --git a/Marlin/ultralcd_st7920_u8glib_rrd.h b/Marlin/ultralcd_st7920_u8glib_rrd.h
index a87c19e8ee..7226f55c9e 100644
--- a/Marlin/ultralcd_st7920_u8glib_rrd.h
+++ b/Marlin/ultralcd_st7920_u8glib_rrd.h
@@ -59,7 +59,7 @@
   #define CPU_ST7920_DELAY_1 DELAY_0_NOP
   #define CPU_ST7920_DELAY_2 DELAY_0_NOP
   #define CPU_ST7920_DELAY_3 DELAY_1_NOP
-#elif (MOTHERBOARD == BOARD_3DRAG) || (MOTHERBOARD == BOARD_K8200)
+#elif (MOTHERBOARD == BOARD_3DRAG) || (MOTHERBOARD == BOARD_K8200) || (MOTHERBOARD == BOARD_K8400)
   #define CPU_ST7920_DELAY_1 DELAY_0_NOP
   #define CPU_ST7920_DELAY_2 DELAY_3_NOP
   #define CPU_ST7920_DELAY_3 DELAY_0_NOP