Merge pull request #1261 from wgm4321/Development
Add Filament menu and add Filament/Retract settings to config store.
This commit is contained in:
Bo Herrmannsen
commit
a18b625534
|
|
@ -38,15 +38,7 @@ void _EEPROM_readData(int &pos, uint8_t* value, uint8_t size)
|
|||
// wrong data being written to the variables.
|
||||
// ALSO: always make sure the variables in the Store and retrieve sections are in the same order.
|
||||
|
||||
#define EEPROM_VERSION "V10"
|
||||
#ifdef DELTA
|
||||
#undef EEPROM_VERSION
|
||||
#define EEPROM_VERSION "V11"
|
||||
#endif
|
||||
#ifdef SCARA
|
||||
#undef EEPROM_VERSION
|
||||
#define EEPROM_VERSION "V12"
|
||||
#endif
|
||||
#define EEPROM_VERSION "V13"
|
||||
|
||||
#ifdef EEPROM_SETTINGS
|
||||
void Config_StoreSettings()
|
||||
|
|
@ -101,6 +93,31 @@ void Config_StoreSettings()
|
|||
#ifdef SCARA
|
||||
EEPROM_WRITE_VAR(i,axis_scaling); // Add scaling for SCARA
|
||||
#endif
|
||||
#ifdef FWRETRACT
|
||||
EEPROM_WRITE_VAR(i,autoretract_enabled);
|
||||
EEPROM_WRITE_VAR(i,retract_length);
|
||||
#if EXTRUDERS > 1
|
||||
EEPROM_WRITE_VAR(i,retract_length_swap);
|
||||
#endif
|
||||
EEPROM_WRITE_VAR(i,retract_feedrate);
|
||||
EEPROM_WRITE_VAR(i,retract_zlift);
|
||||
EEPROM_WRITE_VAR(i,retract_recover_length);
|
||||
#if EXTRUDERS > 1
|
||||
EEPROM_WRITE_VAR(i,retract_recover_length_swap);
|
||||
#endif
|
||||
EEPROM_WRITE_VAR(i,retract_recover_feedrate);
|
||||
#endif
|
||||
|
||||
// Save filament sizes
|
||||
EEPROM_WRITE_VAR(i, volumetric_enabled);
|
||||
EEPROM_WRITE_VAR(i, filament_size[0]);
|
||||
#if EXTRUDERS > 1
|
||||
EEPROM_WRITE_VAR(i, filament_size[1]);
|
||||
#if EXTRUDERS > 2
|
||||
EEPROM_WRITE_VAR(i, filament_size[2]);
|
||||
#endif
|
||||
#endif
|
||||
|
||||
char ver2[4]=EEPROM_VERSION;
|
||||
i=EEPROM_OFFSET;
|
||||
EEPROM_WRITE_VAR(i,ver2); // validate data
|
||||
|
|
@ -211,8 +228,42 @@ SERIAL_ECHOLNPGM("Scaling factors:");
|
|||
SERIAL_ECHOLNPGM("Recover: S=Extra length (mm) F:Speed (mm/m)");
|
||||
SERIAL_ECHO_START;
|
||||
SERIAL_ECHOPAIR(" M208 S",retract_recover_length);
|
||||
SERIAL_ECHOPAIR(" F" ,retract_recover_feedrate*60);
|
||||
SERIAL_ECHOPAIR(" F", retract_recover_feedrate*60);
|
||||
SERIAL_ECHOLN("");
|
||||
SERIAL_ECHO_START;
|
||||
SERIAL_ECHOLNPGM("Auto-Retract: S=0 to disable, 1 to interpret extrude-only moves as retracts or recoveries");
|
||||
SERIAL_ECHO_START;
|
||||
SERIAL_ECHOPAIR(" M209 S", (unsigned long)(autoretract_enabled ? 1 : 0));
|
||||
SERIAL_ECHOLN("");
|
||||
#if EXTRUDERS > 1
|
||||
SERIAL_ECHO_START;
|
||||
SERIAL_ECHOLNPGM("Multi-extruder settings:");
|
||||
SERIAL_ECHO_START;
|
||||
SERIAL_ECHOPAIR(" Swap retract length (mm): ", retract_length_swap);
|
||||
SERIAL_ECHOLN("");
|
||||
SERIAL_ECHO_START;
|
||||
SERIAL_ECHOPAIR(" Swap rec. addl. length (mm): ", retract_recover_length_swap);
|
||||
SERIAL_ECHOLN("");
|
||||
#endif
|
||||
SERIAL_ECHO_START;
|
||||
if (volumetric_enabled) {
|
||||
SERIAL_ECHOLNPGM("Filament settings:");
|
||||
SERIAL_ECHO_START;
|
||||
SERIAL_ECHOPAIR(" M200 D", filament_size[0]);
|
||||
SERIAL_ECHOLN("");
|
||||
#if EXTRUDERS > 1
|
||||
SERIAL_ECHO_START;
|
||||
SERIAL_ECHOPAIR(" M200 T1 D", filament_size[1]);
|
||||
SERIAL_ECHOLN("");
|
||||
#if EXTRUDERS > 2
|
||||
SERIAL_ECHO_START;
|
||||
SERIAL_ECHOPAIR(" M200 T2 D", filament_size[2]);
|
||||
SERIAL_ECHOLN("");
|
||||
#endif
|
||||
#endif
|
||||
} else {
|
||||
SERIAL_ECHOLNPGM("Filament settings: Disabled");
|
||||
}
|
||||
#endif
|
||||
}
|
||||
#endif
|
||||
|
|
@ -277,6 +328,30 @@ void Config_RetrieveSettings()
|
|||
EEPROM_READ_VAR(i,axis_scaling);
|
||||
#endif
|
||||
|
||||
#ifdef FWRETRACT
|
||||
EEPROM_READ_VAR(i,autoretract_enabled);
|
||||
EEPROM_READ_VAR(i,retract_length);
|
||||
#if EXTRUDERS > 1
|
||||
EEPROM_READ_VAR(i,retract_length_swap);
|
||||
#endif
|
||||
EEPROM_READ_VAR(i,retract_feedrate);
|
||||
EEPROM_READ_VAR(i,retract_zlift);
|
||||
EEPROM_READ_VAR(i,retract_recover_length);
|
||||
#if EXTRUDERS > 1
|
||||
EEPROM_READ_VAR(i,retract_recover_length_swap);
|
||||
#endif
|
||||
EEPROM_READ_VAR(i,retract_recover_feedrate);
|
||||
#endif
|
||||
|
||||
EEPROM_READ_VAR(i, volumetric_enabled);
|
||||
EEPROM_READ_VAR(i, filament_size[0]);
|
||||
#if EXTRUDERS > 1
|
||||
EEPROM_READ_VAR(i, filament_size[1]);
|
||||
#if EXTRUDERS > 2
|
||||
EEPROM_READ_VAR(i, filament_size[2]);
|
||||
#endif
|
||||
#endif
|
||||
calculate_volumetric_multipliers();
|
||||
// Call updatePID (similar to when we have processed M301)
|
||||
updatePID();
|
||||
SERIAL_ECHO_START;
|
||||
|
|
@ -353,6 +428,31 @@ void Config_ResetDefault()
|
|||
#endif//PID_ADD_EXTRUSION_RATE
|
||||
#endif//PIDTEMP
|
||||
|
||||
#ifdef FWRETRACT
|
||||
autoretract_enabled = false;
|
||||
retract_length = RETRACT_LENGTH;
|
||||
#if EXTRUDERS > 1
|
||||
retract_length_swap = RETRACT_LENGTH_SWAP;
|
||||
#endif
|
||||
retract_feedrate = RETRACT_FEEDRATE;
|
||||
retract_zlift = RETRACT_ZLIFT;
|
||||
retract_recover_length = RETRACT_RECOVER_LENGTH;
|
||||
#if EXTRUDERS > 1
|
||||
retract_recover_length_swap = RETRACT_RECOVER_LENGTH_SWAP;
|
||||
#endif
|
||||
retract_recover_feedrate = RETRACT_RECOVER_FEEDRATE;
|
||||
#endif
|
||||
|
||||
volumetric_enabled = false;
|
||||
filament_size[0] = DEFAULT_NOMINAL_FILAMENT_DIA;
|
||||
#if EXTRUDERS > 1
|
||||
filament_size[1] = DEFAULT_NOMINAL_FILAMENT_DIA;
|
||||
#if EXTRUDERS > 2
|
||||
filament_size[2] = DEFAULT_NOMINAL_FILAMENT_DIA;
|
||||
#endif
|
||||
#endif
|
||||
calculate_volumetric_multipliers();
|
||||
|
||||
SERIAL_ECHO_START;
|
||||
SERIAL_ECHOLNPGM("Hardcoded Default Settings Loaded");
|
||||
|
||||
|
|
|
|||
|
|
@ -209,7 +209,9 @@ extern float homing_feedrate[];
|
|||
extern bool axis_relative_modes[];
|
||||
extern int feedmultiply;
|
||||
extern int extrudemultiply; // Sets extrude multiply factor (in percent) for all extruders
|
||||
extern bool volumetric_enabled;
|
||||
extern int extruder_multiply[EXTRUDERS]; // sets extrude multiply factor (in percent) for each extruder individually
|
||||
extern float filament_size[EXTRUDERS]; // cross-sectional area of filament (in millimeters), typically around 1.75 or 2.85, 0 disables the volumetric calculations for the extruder.
|
||||
extern float volumetric_multiplier[EXTRUDERS]; // reciprocal of cross-sectional area of filament (in square millimeters), stored this way to reduce computational burden in planner
|
||||
extern float current_position[NUM_AXIS] ;
|
||||
extern float add_homing[3];
|
||||
|
|
@ -266,3 +268,5 @@ extern void digipot_i2c_init();
|
|||
#endif
|
||||
|
||||
#endif
|
||||
|
||||
extern void calculate_volumetric_multipliers();
|
||||
|
|
@ -215,6 +215,15 @@ int extruder_multiply[EXTRUDERS] = {100
|
|||
#endif
|
||||
#endif
|
||||
};
|
||||
bool volumetric_enabled = false;
|
||||
float filament_size[EXTRUDERS] = { DEFAULT_NOMINAL_FILAMENT_DIA
|
||||
#if EXTRUDERS > 1
|
||||
, DEFAULT_NOMINAL_FILAMENT_DIA
|
||||
#if EXTRUDERS > 2
|
||||
, DEFAULT_NOMINAL_FILAMENT_DIA
|
||||
#endif
|
||||
#endif
|
||||
};
|
||||
float volumetric_multiplier[EXTRUDERS] = {1.0
|
||||
#if EXTRUDERS > 1
|
||||
, 1.0
|
||||
|
|
@ -2823,21 +2832,7 @@ Sigma_Exit:
|
|||
#endif //BLINKM
|
||||
case 200: // M200 D<millimeters> set filament diameter and set E axis units to cubic millimeters (use S0 to set back to millimeters).
|
||||
{
|
||||
float area = .0;
|
||||
float radius = .0;
|
||||
if(code_seen('D')) {
|
||||
radius = (float)code_value() * .5;
|
||||
if(radius == 0) {
|
||||
area = 1;
|
||||
} else {
|
||||
area = M_PI * pow(radius, 2);
|
||||
}
|
||||
} else {
|
||||
//reserved for setting filament diameter via UFID or filament measuring device
|
||||
break;
|
||||
|
||||
|
||||
}
|
||||
tmp_extruder = active_extruder;
|
||||
if(code_seen('T')) {
|
||||
tmp_extruder = code_value();
|
||||
|
|
@ -2847,7 +2842,32 @@ Sigma_Exit:
|
|||
break;
|
||||
}
|
||||
}
|
||||
volumetric_multiplier[tmp_extruder] = 1 / area;
|
||||
|
||||
float area = .0;
|
||||
if(code_seen('D')) {
|
||||
float diameter = (float)code_value();
|
||||
if (diameter == 0.0) {
|
||||
// setting any extruder filament size disables volumetric on the assumption that
|
||||
// slicers either generate in extruder values as cubic mm or as as filament feeds
|
||||
// for all extruders
|
||||
volumetric_enabled = false;
|
||||
} else {
|
||||
filament_size[tmp_extruder] = (float)code_value();
|
||||
// make sure all extruders have some sane value for the filament size
|
||||
filament_size[0] = (filament_size[0] == 0.0 ? DEFAULT_NOMINAL_FILAMENT_DIA : filament_size[0]);
|
||||
#if EXTRUDERS > 1
|
||||
filament_size[1] = (filament_size[1] == 0.0 ? DEFAULT_NOMINAL_FILAMENT_DIA : filament_size[1]);
|
||||
#if EXTRUDERS > 2
|
||||
filament_size[2] = (filament_size[2] == 0.0 ? DEFAULT_NOMINAL_FILAMENT_DIA : filament_size[2]);
|
||||
#endif
|
||||
#endif
|
||||
volumetric_enabled = true;
|
||||
}
|
||||
} else {
|
||||
//reserved for setting filament diameter via UFID or filament measuring device
|
||||
break;
|
||||
}
|
||||
calculate_volumetric_multipliers();
|
||||
}
|
||||
break;
|
||||
case 201: // M201
|
||||
|
|
@ -4580,3 +4600,29 @@ bool setTargetedHotend(int code){
|
|||
return false;
|
||||
}
|
||||
|
||||
|
||||
float calculate_volumetric_multiplier(float diameter) {
|
||||
float area = .0;
|
||||
float radius = .0;
|
||||
|
||||
radius = diameter * .5;
|
||||
if (! volumetric_enabled || radius == 0) {
|
||||
area = 1;
|
||||
}
|
||||
else {
|
||||
area = M_PI * pow(radius, 2);
|
||||
}
|
||||
|
||||
return 1.0 / area;
|
||||
}
|
||||
|
||||
void calculate_volumetric_multipliers() {
|
||||
volumetric_multiplier[0] = calculate_volumetric_multiplier(filament_size[0]);
|
||||
#if EXTRUDERS > 1
|
||||
volumetric_multiplier[1] = calculate_volumetric_multiplier(filament_size[1]);
|
||||
#if EXTRUDERS > 2
|
||||
volumetric_multiplier[2] = calculate_volumetric_multiplier(filament_size[2]);
|
||||
#endif
|
||||
#endif
|
||||
}
|
||||
|
||||
|
|
|
|||
|
|
@ -86,6 +86,11 @@
|
|||
#define MSG_ESTEPS "Esteps/mm"
|
||||
#define MSG_TEMPERATURE "Temperature"
|
||||
#define MSG_MOTION "Motion"
|
||||
#define MSG_VOLUMETRIC "Filament"
|
||||
#define MSG_VOLUMETRIC_ENABLED "E in mm3"
|
||||
#define MSG_FILAMENT_SIZE_EXTRUDER_0 "Fil. Dia. 1"
|
||||
#define MSG_FILAMENT_SIZE_EXTRUDER_1 "Fil. Dia. 2"
|
||||
#define MSG_FILAMENT_SIZE_EXTRUDER_2 "Fil. Dia. 3"
|
||||
#define MSG_CONTRAST "LCD contrast"
|
||||
#define MSG_STORE_EPROM "Store memory"
|
||||
#define MSG_LOAD_EPROM "Load memory"
|
||||
|
|
|
|||
|
|
@ -59,6 +59,7 @@ static void lcd_control_temperature_menu();
|
|||
static void lcd_control_temperature_preheat_pla_settings_menu();
|
||||
static void lcd_control_temperature_preheat_abs_settings_menu();
|
||||
static void lcd_control_motion_menu();
|
||||
static void lcd_control_volumetric_menu();
|
||||
#ifdef DOGLCD
|
||||
static void lcd_set_contrast();
|
||||
#endif
|
||||
|
|
@ -82,6 +83,7 @@ static void menu_action_setting_edit_bool(const char* pstr, bool* ptr);
|
|||
static void menu_action_setting_edit_int3(const char* pstr, int* ptr, int minValue, int maxValue);
|
||||
static void menu_action_setting_edit_float3(const char* pstr, float* ptr, float minValue, float maxValue);
|
||||
static void menu_action_setting_edit_float32(const char* pstr, float* ptr, float minValue, float maxValue);
|
||||
static void menu_action_setting_edit_float43(const char* pstr, float* ptr, float minValue, float maxValue);
|
||||
static void menu_action_setting_edit_float5(const char* pstr, float* ptr, float minValue, float maxValue);
|
||||
static void menu_action_setting_edit_float51(const char* pstr, float* ptr, float minValue, float maxValue);
|
||||
static void menu_action_setting_edit_float52(const char* pstr, float* ptr, float minValue, float maxValue);
|
||||
|
|
@ -90,6 +92,7 @@ static void menu_action_setting_edit_callback_bool(const char* pstr, bool* ptr,
|
|||
static void menu_action_setting_edit_callback_int3(const char* pstr, int* ptr, int minValue, int maxValue, menuFunc_t callbackFunc);
|
||||
static void menu_action_setting_edit_callback_float3(const char* pstr, float* ptr, float minValue, float maxValue, menuFunc_t callbackFunc);
|
||||
static void menu_action_setting_edit_callback_float32(const char* pstr, float* ptr, float minValue, float maxValue, menuFunc_t callbackFunc);
|
||||
static void menu_action_setting_edit_callback_float43(const char* pstr, float* ptr, float minValue, float maxValue, menuFunc_t callbackFunc);
|
||||
static void menu_action_setting_edit_callback_float5(const char* pstr, float* ptr, float minValue, float maxValue, menuFunc_t callbackFunc);
|
||||
static void menu_action_setting_edit_callback_float51(const char* pstr, float* ptr, float minValue, float maxValue, menuFunc_t callbackFunc);
|
||||
static void menu_action_setting_edit_callback_float52(const char* pstr, float* ptr, float minValue, float maxValue, menuFunc_t callbackFunc);
|
||||
|
|
@ -742,6 +745,8 @@ static void lcd_control_menu()
|
|||
MENU_ITEM(back, MSG_MAIN, lcd_main_menu);
|
||||
MENU_ITEM(submenu, MSG_TEMPERATURE, lcd_control_temperature_menu);
|
||||
MENU_ITEM(submenu, MSG_MOTION, lcd_control_motion_menu);
|
||||
MENU_ITEM(submenu, MSG_VOLUMETRIC, lcd_control_volumetric_menu);
|
||||
|
||||
#ifdef DOGLCD
|
||||
// MENU_ITEM_EDIT(int3, MSG_CONTRAST, &lcd_contrast, 0, 63);
|
||||
MENU_ITEM(submenu, MSG_CONTRAST, lcd_set_contrast);
|
||||
|
|
@ -870,6 +875,26 @@ static void lcd_control_motion_menu()
|
|||
END_MENU();
|
||||
}
|
||||
|
||||
static void lcd_control_volumetric_menu()
|
||||
{
|
||||
START_MENU();
|
||||
MENU_ITEM(back, MSG_CONTROL, lcd_control_menu);
|
||||
|
||||
MENU_ITEM_EDIT(bool, MSG_VOLUMETRIC_ENABLED, &volumetric_enabled);
|
||||
|
||||
if (volumetric_enabled) {
|
||||
MENU_ITEM_EDIT_CALLBACK(float43, MSG_FILAMENT_SIZE_EXTRUDER_0, &filament_size[0], DEFAULT_NOMINAL_FILAMENT_DIA - .5, DEFAULT_NOMINAL_FILAMENT_DIA + .5, calculate_volumetric_multipliers);
|
||||
#if EXTRUDERS > 1
|
||||
MENU_ITEM_EDIT_CALLBACK(float43, MSG_FILAMENT_SIZE_EXTRUDER_1, &filament_size[1], DEFAULT_NOMINAL_FILAMENT_DIA - .5, DEFAULT_NOMINAL_FILAMENT_DIA + .5, calculate_volumetric_multipliers);
|
||||
#if EXTRUDERS > 2
|
||||
MENU_ITEM_EDIT_CALLBACK(float43, MSG_FILAMENT_SIZE_EXTRUDER_2, &filament_size[2], DEFAULT_NOMINAL_FILAMENT_DIA - .5, DEFAULT_NOMINAL_FILAMENT_DIA + .5, calculate_volumetric_multipliers);
|
||||
#endif
|
||||
#endif
|
||||
}
|
||||
|
||||
END_MENU();
|
||||
}
|
||||
|
||||
#ifdef DOGLCD
|
||||
static void lcd_set_contrast()
|
||||
{
|
||||
|
|
@ -1013,6 +1038,7 @@ void lcd_sdcard_menu()
|
|||
menu_edit_type(int, int3, itostr3, 1)
|
||||
menu_edit_type(float, float3, ftostr3, 1)
|
||||
menu_edit_type(float, float32, ftostr32, 100)
|
||||
menu_edit_type(float, float43, ftostr43, 1000)
|
||||
menu_edit_type(float, float5, ftostr5, 0.01)
|
||||
menu_edit_type(float, float51, ftostr51, 10)
|
||||
menu_edit_type(float, float52, ftostr52, 100)
|
||||
|
|
@ -1482,7 +1508,24 @@ char *ftostr32(const float &x)
|
|||
return conv;
|
||||
}
|
||||
|
||||
// Convert float to string with 1.23 format
|
||||
// Convert float to string with 1.234 format
|
||||
char *ftostr43(const float &x)
|
||||
{
|
||||
long xx = x * 1000;
|
||||
if (xx >= 0)
|
||||
conv[0] = (xx / 1000) % 10 + '0';
|
||||
else
|
||||
conv[0] = '-';
|
||||
xx = abs(xx);
|
||||
conv[1] = '.';
|
||||
conv[2] = (xx / 100) % 10 + '0';
|
||||
conv[3] = (xx / 10) % 10 + '0';
|
||||
conv[4] = (xx) % 10 + '0';
|
||||
conv[5] = 0;
|
||||
return conv;
|
||||
}
|
||||
|
||||
//Float to string with 1.23 format
|
||||
char *ftostr12ns(const float &x)
|
||||
{
|
||||
long xx=x*100;
|
||||
|
|
|
|||
|
|
@ -118,6 +118,7 @@ char *ftostr3(const float &x);
|
|||
char *ftostr31ns(const float &x); // float to string without sign character
|
||||
char *ftostr31(const float &x);
|
||||
char *ftostr32(const float &x);
|
||||
char *ftostr43(const float &x);
|
||||
char *ftostr12ns(const float &x);
|
||||
char *ftostr32sp(const float &x); // remove zero-padding from ftostr32
|
||||
char *ftostr5(const float &x);
|
||||
|
|
|
|||
|
|
@ -693,6 +693,8 @@ static void lcd_implementation_drawmenu_setting_edit_generic_P(uint8_t row, cons
|
|||
#define lcd_implementation_drawmenu_setting_edit_float3(row, pstr, pstr2, data, minValue, maxValue) lcd_implementation_drawmenu_setting_edit_generic(row, pstr, ' ', ftostr3(*(data)))
|
||||
#define lcd_implementation_drawmenu_setting_edit_float32_selected(row, pstr, pstr2, data, minValue, maxValue) lcd_implementation_drawmenu_setting_edit_generic(row, pstr, '>', ftostr32(*(data)))
|
||||
#define lcd_implementation_drawmenu_setting_edit_float32(row, pstr, pstr2, data, minValue, maxValue) lcd_implementation_drawmenu_setting_edit_generic(row, pstr, ' ', ftostr32(*(data)))
|
||||
#define lcd_implementation_drawmenu_setting_edit_float43_selected(row, pstr, pstr2, data, minValue, maxValue) lcd_implementation_drawmenu_setting_edit_generic(row, pstr, '>', ftostr43(*(data)))
|
||||
#define lcd_implementation_drawmenu_setting_edit_float43(row, pstr, pstr2, data, minValue, maxValue) lcd_implementation_drawmenu_setting_edit_generic(row, pstr, ' ', ftostr43(*(data)))
|
||||
#define lcd_implementation_drawmenu_setting_edit_float5_selected(row, pstr, pstr2, data, minValue, maxValue) lcd_implementation_drawmenu_setting_edit_generic(row, pstr, '>', ftostr5(*(data)))
|
||||
#define lcd_implementation_drawmenu_setting_edit_float5(row, pstr, pstr2, data, minValue, maxValue) lcd_implementation_drawmenu_setting_edit_generic(row, pstr, ' ', ftostr5(*(data)))
|
||||
#define lcd_implementation_drawmenu_setting_edit_float52_selected(row, pstr, pstr2, data, minValue, maxValue) lcd_implementation_drawmenu_setting_edit_generic(row, pstr, '>', ftostr52(*(data)))
|
||||
|
|
@ -711,6 +713,8 @@ static void lcd_implementation_drawmenu_setting_edit_generic_P(uint8_t row, cons
|
|||
#define lcd_implementation_drawmenu_setting_edit_callback_float3(row, pstr, pstr2, data, minValue, maxValue, callback) lcd_implementation_drawmenu_setting_edit_generic(row, pstr, ' ', ftostr3(*(data)))
|
||||
#define lcd_implementation_drawmenu_setting_edit_callback_float32_selected(row, pstr, pstr2, data, minValue, maxValue, callback) lcd_implementation_drawmenu_setting_edit_generic(row, pstr, '>', ftostr32(*(data)))
|
||||
#define lcd_implementation_drawmenu_setting_edit_callback_float32(row, pstr, pstr2, data, minValue, maxValue, callback) lcd_implementation_drawmenu_setting_edit_generic(row, pstr, ' ', ftostr32(*(data)))
|
||||
#define lcd_implementation_drawmenu_setting_edit_callback_float43_selected(row, pstr, pstr2, data, minValue, maxValue, callback) lcd_implementation_drawmenu_setting_edit_generic(row, pstr, '>', ftostr43(*(data)))
|
||||
#define lcd_implementation_drawmenu_setting_edit_callback_float43(row, pstr, pstr2, data, minValue, maxValue, callback) lcd_implementation_drawmenu_setting_edit_generic(row, pstr, ' ', ftostr43(*(data)))
|
||||
#define lcd_implementation_drawmenu_setting_edit_callback_float5_selected(row, pstr, pstr2, data, minValue, maxValue, callback) lcd_implementation_drawmenu_setting_edit_generic(row, pstr, '>', ftostr5(*(data)))
|
||||
#define lcd_implementation_drawmenu_setting_edit_callback_float5(row, pstr, pstr2, data, minValue, maxValue, callback) lcd_implementation_drawmenu_setting_edit_generic(row, pstr, ' ', ftostr5(*(data)))
|
||||
#define lcd_implementation_drawmenu_setting_edit_callback_float52_selected(row, pstr, pstr2, data, minValue, maxValue, callback) lcd_implementation_drawmenu_setting_edit_generic(row, pstr, '>', ftostr52(*(data)))
|
||||
|
|
|
|||
Loading…
Reference in a new issue