More featureful CR-10S configuration

Marlin/src/config/examples/Creality/CR-10S/Configuration.h

@@ -620,7 +620,7 @@
  * Use G29 repeatedly, adjusting the Z height at each point with movement commands
  * or (with LCD_BED_LEVELING) the LCD controller.
  */
-//#define PROBE_MANUALLY
+#define PROBE_MANUALLY
 
 /**
  * A Fix-Mounted Probe either doesn't deploy or needs manual deployment.
@@ -768,7 +768,7 @@
 
 //#define NO_MOTION_BEFORE_HOMING  // Inhibit movement until all axes have been homed
 
-//#define Z_HOMING_HEIGHT 4  // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
+#define Z_HOMING_HEIGHT 4    // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
                              // Be sure you have this distance over your Z_MAX_POS in case.
 
 // Direction of endstops when homing; 1=MAX, -1=MIN
@@ -871,9 +871,9 @@
  */
 //#define AUTO_BED_LEVELING_3POINT
 //#define AUTO_BED_LEVELING_LINEAR
-//#define AUTO_BED_LEVELING_BILINEAR
+#define AUTO_BED_LEVELING_BILINEAR
 //#define AUTO_BED_LEVELING_UBL
-#define MESH_BED_LEVELING
+//#define MESH_BED_LEVELING
 
 /**
  * Enable detailed logging of G28, G29, M48, etc.
@@ -899,10 +899,10 @@
    */
   #define G26_MESH_VALIDATION   // Enable G26 mesh validation
   #if ENABLED(G26_MESH_VALIDATION)
-    #define MESH_TEST_NOZZLE_SIZE     0.4   // (mm) Diameter of primary nozzle.
+    #define MESH_TEST_NOZZLE_SIZE    0.4  // (mm) Diameter of primary nozzle.
-    #define MESH_TEST_LAYER_HEIGHT    0.2   // (mm) Default layer height for the G26 Mesh Validation Tool.
+    #define MESH_TEST_LAYER_HEIGHT   0.2  // (mm) Default layer height for the G26 Mesh Validation Tool.
-    #define MESH_TEST_HOTEND_TEMP   205.0   // (°C) Default nozzle temperature for the G26 Mesh Validation Tool.
+    #define MESH_TEST_HOTEND_TEMP  205.0  // (°C) Default nozzle temperature for the G26 Mesh Validation Tool.
-    #define MESH_TEST_BED_TEMP       60.0   // (°C) Default bed temperature for the G26 Mesh Validation Tool.
+    #define MESH_TEST_BED_TEMP      60.0  // (°C) Default bed temperature for the G26 Mesh Validation Tool.
   #endif
 
 #endif
@@ -1113,8 +1113,8 @@
 // M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
 // M502 - reverts to the default "factory settings".  You still need to store them in EEPROM afterwards if you want to.
 //
-#define EEPROM_SETTINGS // Enable for M500 and M501 commands
+#define EEPROM_SETTINGS   // Enable for M500 and M501 commands
-#define DISABLE_M503    // Saves ~2700 bytes of PROGMEM. Disable for release!
+//#define DISABLE_M503    // Saves ~2700 bytes of PROGMEM. Disable for release!
 #define EEPROM_CHITCHAT   // Give feedback on EEPROM commands. Disable to save PROGMEM.
 
 //

Marlin/src/config/examples/Creality/CR-10S/Configuration_adv.h

@@ -123,7 +123,7 @@
 #endif
 
 // Show extra position information in M114
-//#define M114_DETAIL
+#define M114_DETAIL
 
 // Show Temperature ADC value
 // Enable for M105 to include ADC values read from temperature sensors.
@@ -471,7 +471,7 @@
 // @section lcd
 
 // Include a page of printer information in the LCD Main Menu
-//#define LCD_INFO_MENU
+#define LCD_INFO_MENU
 
 // Leave out seldom-used LCD menu items to recover some Program Memory
 //#define SLIM_LCD_MENUS
@@ -552,7 +552,7 @@
     #define FOLDER_SORTING     -1     // -1=above  0=none  1=below
     #define SDSORT_GCODE       false  // Allow turning sorting on/off with LCD and M34 g-code.
     #define SDSORT_USES_RAM    true   // Pre-allocate a static array for faster pre-sorting.
-    #define SDSORT_USES_STACK  false  // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.)
+    #define SDSORT_USES_STACK  true   // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.)
     #define SDSORT_CACHE_NAMES false  // Keep sorted items in RAM longer for speedy performance. Most expensive option.
     #define SDSORT_DYNAMIC_RAM false  // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use!
     #define SDSORT_CACHE_VFATS 2      // Maximum number of 13-byte VFAT entries to use for sorting.
@@ -582,7 +582,7 @@
   //#define LONG_FILENAME_HOST_SUPPORT
 
   // Enable this option to scroll long filenames in the SD card menu
-  //#define SCROLL_LONG_FILENAMES
+  #define SCROLL_LONG_FILENAMES
 
   /**
    * This option allows you to abort SD printing when any endstop is triggered.
@@ -614,7 +614,7 @@
  */
 #if ENABLED(DOGLCD)
   // Show SD percentage next to the progress bar
-  //#define DOGM_SD_PERCENT
+  #define DOGM_SD_PERCENT
 
   // Enable to save many cycles by drawing a hollow frame on the Info Screen
   #define XYZ_HOLLOW_FRAME
@@ -736,7 +736,7 @@
 //
 // G2/G3 Arc Support
 //
-//#define ARC_SUPPORT               // Disable this feature to save ~3226 bytes
+#define ARC_SUPPORT               // Disable this feature to save ~3226 bytes
 #if ENABLED(ARC_SUPPORT)
   #define MM_PER_ARC_SEGMENT  1   // Length of each arc segment
   #define N_ARC_CORRECTION   25   // Number of intertpolated segments between corrections
@@ -821,7 +821,7 @@
 // enter the serial receive buffer, so they cannot be blocked.
 // Currently handles M108, M112, M410
 // Does not work on boards using AT90USB (USBCON) processors!
-//#define EMERGENCY_PARSER
+#define EMERGENCY_PARSER
 
 // Bad Serial-connections can miss a received command by sending an 'ok'
 // Therefore some clients abort after 30 seconds in a timeout.
@@ -830,7 +830,7 @@
 //#define NO_TIMEOUTS 1000 // Milliseconds
 
 // Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary.
-//#define ADVANCED_OK
+#define ADVANCED_OK
 
 // @section extras