First parts 2nd extruder

Marlin/Configuration.h

@@ -8,6 +8,7 @@
 //#define BAUDRATE 115200
 //#define BAUDRATE 230400
 
+#define EXTRUDERS 1
 
 // Frequency limit
 // See nophead's blog for more info

Marlin/Marlin.pde

@@ -174,7 +174,7 @@ static unsigned long stepper_inactive_time = 0;
 static unsigned long starttime=0;
 static unsigned long stoptime=0;
 
-
+static uint8_t tmp_extruder;
 
 //===========================================================================
 //=============================ROUTINES=============================
@@ -641,7 +641,6 @@ inline void process_commands()
       //processed in write to file routine above
       //card,saving = false;
       break;
-      
     #endif //SDSUPPORT
 
     case 30: //M30 take time since the start of the SD print or an M109 command
@@ -684,19 +683,36 @@ inline void process_commands()
       }
      break;
     case 104: // M104
-      if (code_seen('S')) setTargetHotend0(code_value());
+      tmp_extruder = active_extruder;
+      if(code_seen('T')) {
+        tmp_extruder = code_value();
+        if(tmp_extruder >= EXTRUDERS) {
+          SERIAL_ECHO_START;
+          SERIAL_ECHO("M104 Invalid extruder ");
+          SERIAL_ECHOLN(tmp_extruder);
+          break;
+        }
+      }
+      if (code_seen('S')) setTargetHotend(code_value(), tmp_extruder);
       setWatch();
       break;
     case 140: // M140 set bed temp
       if (code_seen('S')) setTargetBed(code_value());
       break;
     case 105 : // M105
-      //SERIAL_ECHOLN(freeMemory());
+      tmp_extruder = active_extruder;
-       //test watchdog:
+      if(code_seen('T')) {
-       //delay(20000);
+        tmp_extruder = code_value();
-      #if (TEMP_0_PIN > -1) || defined (HEATER_USES_AD595)
+        if(tmp_extruder >= EXTRUDERS) {
+          SERIAL_ECHO_START;
+          SERIAL_ECHO("M105 Invalid extruder ");
+          SERIAL_ECHOLN(tmp_extruder);
+          break;
+        }
+      }
+      #if (TEMP_0_PIN > -1) || (TEMP_2_PIN > -1)
         SERIAL_PROTOCOLPGM("ok T:");
-        SERIAL_PROTOCOL( degHotend0()); 
+        SERIAL_PROTOCOL( degHotend(tmp_extruder)); 
         #if TEMP_1_PIN > -1 
           SERIAL_PROTOCOLPGM(" B:");  
           SERIAL_PROTOCOL(degBed());
@@ -715,14 +731,24 @@ inline void process_commands()
       break;
     case 109: 
     {// M109 - Wait for extruder heater to reach target.
+      tmp_extruder = active_extruder;
+      if(code_seen('T')) {
+        tmp_extruder = code_value();
+        if(tmp_extruder >= EXTRUDERS) {
+          SERIAL_ECHO_START;
+          SERIAL_ECHO("M109 Invalid extruder ");
+          SERIAL_ECHOLN(tmp_extruder);
+          break;
+        }
+      }
       LCD_MESSAGEPGM("Heating...");   
       #ifdef AUTOTEMP
         autotemp_enabled=false;
       #endif
-        if (code_seen('S')) setTargetHotend0(code_value());
+      if (code_seen('S')) setTargetHotend(code_value(), tmp_extruder);
       #ifdef AUTOTEMP
         if (code_seen('S')) autotemp_min=code_value();
-          if (code_seen('T')) autotemp_max=code_value();
+        if (code_seen('G')) autotemp_max=code_value();
         if (code_seen('F')) 
         {
           autotemp_factor=code_value();
@@ -734,22 +760,22 @@ inline void process_commands()
       codenum = millis(); 
 
       /* See if we are heating up or cooling down */
-        bool target_direction = isHeatingHotend0(); // true if heating, false if cooling
+      bool target_direction = isHeatingHotend(tmp_extruder); // true if heating, false if cooling
 
       #ifdef TEMP_RESIDENCY_TIME
         long residencyStart;
         residencyStart = -1;
         /* continue to loop until we have reached the target temp   
           _and_ until TEMP_RESIDENCY_TIME hasn't passed since we reached it */
-          while((target_direction ? (isHeatingHotend0()) : (isCoolingHotend0())) ||
+        while((target_direction ? (isHeatingHotend(tmp_extruder)) : (isCoolingHotend(tmp_extruder))) ||
                 (residencyStart > -1 && (millis() - residencyStart) < TEMP_RESIDENCY_TIME*1000) ) {
       #else
-          while ( target_direction ? (isHeatingHotend0()) : (isCoolingHotend0()&&(CooldownNoWait==false)) ) {
+        while ( target_direction ? (isHeatingHotend(tmp_extruder)) : (isCoolingHotend(tmp_extruder)&&(CooldownNoWait==false)) ) {
       #endif //TEMP_RESIDENCY_TIME
         if( (millis() - codenum) > 1000 ) 
         { //Print Temp Reading every 1 second while heating up/cooling down
           SERIAL_PROTOCOLPGM("T:");
-          SERIAL_PROTOCOLLN( degHotend0() ); 
+          SERIAL_PROTOCOLLN( degHotend(tmp_extruder) ); 
           codenum = millis();
         }
         manage_heater();
@@ -757,9 +783,9 @@ inline void process_commands()
         #ifdef TEMP_RESIDENCY_TIME
             /* start/restart the TEMP_RESIDENCY_TIME timer whenever we reach target temp for the first time
               or when current temp falls outside the hysteresis after target temp was reached */
-          if ((residencyStart == -1 &&  target_direction && !isHeatingHotend0()) ||
+          if ((residencyStart == -1 &&  target_direction && !isHeatingHotend(tmp_extruder)) ||
-              (residencyStart == -1 && !target_direction && !isCoolingHotend0()) ||
+              (residencyStart == -1 && !target_direction && !isCoolingHotend(tmp_extruder)) ||
-              (residencyStart > -1 && labs(degHotend0() - degTargetHotend0()) > TEMP_HYSTERESIS) ) 
+              (residencyStart > -1 && labs(degHotend(tmp_extruder) - degTargetHotend(tmp_extruder)) > TEMP_HYSTERESIS) ) 
           {
             residencyStart = millis();
           }
@@ -943,8 +969,6 @@ inline void process_commands()
     #ifdef PIDTEMP
     case 301: // M301
       {
-        
-       
         if(code_seen('P')) Kp = code_value();
         if(code_seen('I')) Ki = code_value()*PID_dT;
         if(code_seen('D')) Kd = code_value()/PID_dT;
@@ -989,6 +1013,18 @@ inline void process_commands()
 
     }
   }
+  else if(code_seen('T')) {
+    tmp_extruder = code_value();
+    if(tmp_extruder >= EXTRUDERS) {
+      SERIAL_ECHO_START;
+      SERIAL_ECHO("T");
+      SERIAL_ECHO(tmp_extruder);
+      SERIAL_ECHOLN("Invalid extruder");
+    }
+    else {
+      active_extruder = tmp_extruder;
+    }
+  }
   else
   {
     SERIAL_ECHO_START;

Marlin/planner.cpp

@@ -81,6 +81,8 @@ float max_z_jerk;
 float mintravelfeedrate;
 unsigned long axis_steps_per_sqr_second[NUM_AXIS];
 
+uint8_t active_extruder = 0;
+
 // The current position of the tool in absolute steps
 long position[4];   //rescaled from extern when axis_steps_per_unit are changed by gcode
 static float previous_speed[4]; // Speed of previous path line segment

Marlin/planner.h

@@ -94,6 +94,7 @@ extern float max_z_jerk;
 extern float mintravelfeedrate;
 extern unsigned long axis_steps_per_sqr_second[NUM_AXIS];
 
+extern uint8_t active_extruder;
 
 #ifdef AUTOTEMP
     extern bool autotemp_enabled;

Marlin/temperature.h

@@ -62,9 +62,18 @@ extern float Kp,Ki,Kd,Kc;
 inline float degHotend0(){  return analog2temp(current_raw[TEMPSENSOR_HOTEND_0]);};
 inline float degHotend1(){  return analog2temp(current_raw[TEMPSENSOR_HOTEND_1]);};
 inline float degBed() {  return analog2tempBed(current_raw[TEMPSENSOR_BED]);};
+inline float degHotend(uint8_t extruder){  
+  if(extruder == 0) return analog2temp(current_raw[TEMPSENSOR_HOTEND_0]);
+  if(extruder == 1) return analog2temp(current_raw[TEMPSENSOR_HOTEND_1]);
+};
 
 inline float degTargetHotend0() {  return analog2temp(target_raw[TEMPSENSOR_HOTEND_0]);};
 inline float degTargetHotend1() {  return analog2temp(target_raw[TEMPSENSOR_HOTEND_1]);};
+inline float degTargetHotend(uint8_t extruder){  
+  if(extruder == 0) return analog2temp(target_raw[TEMPSENSOR_HOTEND_0]);
+  if(extruder == 1) return analog2temp(target_raw[TEMPSENSOR_HOTEND_1]);
+};
+
 inline float degTargetBed() {   return analog2tempBed(target_raw[TEMPSENSOR_BED]);};
 
 inline void setTargetHotend0(const float &celsius) 
@@ -75,14 +84,26 @@ inline void setTargetHotend0(const float &celsius)
   #endif //PIDTEMP
 };
 inline void setTargetHotend1(const float &celsius) {  target_raw[TEMPSENSOR_HOTEND_1]=temp2analog(celsius);};
+inline float setTargetHotend(const float &celcius, uint8_t extruder){  
+  if(extruder == 0) setTargetHotend0(celcius);
+  if(extruder == 1) setTargetHotend1(celcius);
+};
 inline void setTargetBed(const float &celsius)     {  target_raw[TEMPSENSOR_BED     ]=temp2analogBed(celsius);};
 
 inline bool isHeatingHotend0() {return target_raw[TEMPSENSOR_HOTEND_0] > current_raw[TEMPSENSOR_HOTEND_0];};
 inline bool isHeatingHotend1() {return target_raw[TEMPSENSOR_HOTEND_1] > current_raw[TEMPSENSOR_HOTEND_1];};
+inline float isHeatingHotend(uint8_t extruder){  
+  if(extruder == 0) return target_raw[TEMPSENSOR_HOTEND_0] > current_raw[TEMPSENSOR_HOTEND_0];
+  if(extruder == 1) return target_raw[TEMPSENSOR_HOTEND_1] > current_raw[TEMPSENSOR_HOTEND_1];
+};
 inline bool isHeatingBed() {return target_raw[TEMPSENSOR_BED] > current_raw[TEMPSENSOR_BED];};
 
 inline bool isCoolingHotend0() {return target_raw[TEMPSENSOR_HOTEND_0] < current_raw[TEMPSENSOR_HOTEND_0];};
 inline bool isCoolingHotend1() {return target_raw[TEMPSENSOR_HOTEND_1] < current_raw[TEMPSENSOR_HOTEND_1];};
+inline float isCoolingHotend(uint8_t extruder){  
+  if(extruder == 0) return target_raw[TEMPSENSOR_HOTEND_0] < current_raw[TEMPSENSOR_HOTEND_0];
+  if(extruder == 1) return target_raw[TEMPSENSOR_HOTEND_1] < current_raw[TEMPSENSOR_HOTEND_1];
+};
 inline bool isCoolingBed() {return target_raw[TEMPSENSOR_BED] < current_raw[TEMPSENSOR_BED];};
 
 void disable_heater();