zaubentrucker/muele-marlin
1
0
Fork 0
Code Issues Pull requests Actions Packages Projects Releases Wiki Activity

Power Loss Recovery with a UPS (#15943)

Browse source
This commit is contained in:
BigTreeTech 2019-11-21 07:40:21 +08:00 committed by Scott Lahteine
parent ab9f0f2c4f
commit ab8b24fdba
111 changed files with 290 additions and 31 deletions
Show stats Download patch file Download diff file Expand all files Collapse all files

2
Marlin/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

39
Marlin/src/HAL/HAL_STM32F1/fastio.h
View file

@ -29,32 +29,33 @@
#include <libmaple/gpio.h>
#define READ(IO) (PIN_MAP[IO].gpio_device->regs->IDR & (1U << PIN_MAP[IO].gpio_bit) ? HIGH : LOW)
#define WRITE(IO,V) (PIN_MAP[IO].gpio_device->regs->BSRR = (1U << PIN_MAP[IO].gpio_bit) << ((V) ? 0 : 16))
#define TOGGLE(IO) (PIN_MAP[IO].gpio_device->regs->ODR = PIN_MAP[IO].gpio_device->regs->ODR ^ (1U << PIN_MAP[IO].gpio_bit))
#define READ(IO) (PIN_MAP[IO].gpio_device->regs->IDR & (1U << PIN_MAP[IO].gpio_bit) ? HIGH : LOW)
#define WRITE(IO,V) (PIN_MAP[IO].gpio_device->regs->BSRR = (1U << PIN_MAP[IO].gpio_bit) << ((V) ? 0 : 16))
#define TOGGLE(IO) (PIN_MAP[IO].gpio_device->regs->ODR = PIN_MAP[IO].gpio_device->regs->ODR ^ (1U << PIN_MAP[IO].gpio_bit))
#define _GET_MODE(IO) gpio_get_mode(PIN_MAP[IO].gpio_device, PIN_MAP[IO].gpio_bit)
#define _SET_MODE(IO,M) gpio_set_mode(PIN_MAP[IO].gpio_device, PIN_MAP[IO].gpio_bit, M)
#define _SET_OUTPUT(IO) _SET_MODE(IO, GPIO_OUTPUT_PP)
#define _SET_OUTPUT_OD(IO) _SET_MODE(IO, GPIO_OUTPUT_OD)
#define _GET_MODE(IO) gpio_get_mode(PIN_MAP[IO].gpio_device, PIN_MAP[IO].gpio_bit)
#define _SET_MODE(IO,M) gpio_set_mode(PIN_MAP[IO].gpio_device, PIN_MAP[IO].gpio_bit, M)
#define _SET_OUTPUT(IO) _SET_MODE(IO, GPIO_OUTPUT_PP)
#define _SET_OUTPUT_OD(IO) _SET_MODE(IO, GPIO_OUTPUT_OD)
#define OUT_WRITE(IO,V) do{ _SET_OUTPUT(IO); WRITE(IO,V); }while(0)
#define OUT_WRITE_OD(IO,V) do{ _SET_OUTPUT_OD(IO); WRITE(IO,V); }while(0)
#define OUT_WRITE(IO,V) do{ _SET_OUTPUT(IO); WRITE(IO,V); }while(0)
#define OUT_WRITE_OD(IO,V) do{ _SET_OUTPUT_OD(IO); WRITE(IO,V); }while(0)
#define SET_INPUT(IO) _SET_MODE(IO, GPIO_INPUT_FLOATING)
#define SET_INPUT_PULLUP(IO) _SET_MODE(IO, GPIO_INPUT_PU)
#define SET_OUTPUT(IO) OUT_WRITE(IO, LOW)
#define SET_PWM(IO) pinMode(IO, PWM) // do{ gpio_set_mode(PIN_MAP[pin].gpio_device, PIN_MAP[pin].gpio_bit, GPIO_AF_OUTPUT_PP); timer_set_mode(PIN_MAP[pin].timer_device, PIN_MAP[pin].timer_channel, TIMER_PWM); }while(0)
#define SET_PWM_OD(IO) pinMode(IO, PWM_OPEN_DRAIN)
#define SET_INPUT(IO) _SET_MODE(IO, GPIO_INPUT_FLOATING)
#define SET_INPUT_PULLUP(IO) _SET_MODE(IO, GPIO_INPUT_PU)
#define SET_INPUT_PULLDOWN(IO) _SET_MODE(IO, GPIO_INPUT_PD)
#define SET_OUTPUT(IO) OUT_WRITE(IO, LOW)
#define SET_PWM(IO) pinMode(IO, PWM) // do{ gpio_set_mode(PIN_MAP[pin].gpio_device, PIN_MAP[pin].gpio_bit, GPIO_AF_OUTPUT_PP); timer_set_mode(PIN_MAP[pin].timer_device, PIN_MAP[pin].timer_channel, TIMER_PWM); }while(0)
#define SET_PWM_OD(IO) pinMode(IO, PWM_OPEN_DRAIN)
#define IS_INPUT(IO) (_GET_MODE(IO) == GPIO_INPUT_FLOATING || _GET_MODE(IO) == GPIO_INPUT_ANALOG || _GET_MODE(IO) == GPIO_INPUT_PU || _GET_MODE(IO) == GPIO_INPUT_PD)
#define IS_OUTPUT(IO) (_GET_MODE(IO) == GPIO_OUTPUT_PP || _GET_MODE(IO) == GPIO_OUTPUT_OD)
#define IS_INPUT(IO) (_GET_MODE(IO) == GPIO_INPUT_FLOATING || _GET_MODE(IO) == GPIO_INPUT_ANALOG || _GET_MODE(IO) == GPIO_INPUT_PU || _GET_MODE(IO) == GPIO_INPUT_PD)
#define IS_OUTPUT(IO) (_GET_MODE(IO) == GPIO_OUTPUT_PP || _GET_MODE(IO) == GPIO_OUTPUT_OD)
#define PWM_PIN(IO) (PIN_MAP[IO].timer_device != nullptr)
#define PWM_PIN(IO) (PIN_MAP[IO].timer_device != nullptr)
// digitalRead/Write wrappers
#define extDigitalRead(IO) digitalRead(IO)
#define extDigitalWrite(IO,V) digitalWrite(IO,V)
#define extDigitalRead(IO) digitalRead(IO)
#define extDigitalWrite(IO,V) digitalWrite(IO,V)
//
// Pins Definitions

51
Marlin/src/feature/power_loss_recovery.cpp
View file

@ -65,6 +65,9 @@ PrintJobRecovery recovery;
#ifndef POWER_LOSS_RETRACT_LEN
#define POWER_LOSS_RETRACT_LEN 0
#endif
#ifndef POWER_LOSS_ZRAISE
#define POWER_LOSS_ZRAISE 2
#endif
/**
* Clear the recovery info
@ -235,10 +238,34 @@ void PrintJobRecovery::save(const bool force/*=false*/, const bool save_queue/*=
}
#if PIN_EXISTS(POWER_LOSS)
void PrintJobRecovery::_outage() {
save(true);
#if ENABLED(BACKUP_POWER_SUPPLY)
static bool lock = false;
if (lock) return; // No re-entrance from idle() during raise_z()
lock = true;
#endif
if (IS_SD_PRINTING()) save(true);
#if ENABLED(BACKUP_POWER_SUPPLY)
raise_z();
#endif
kill(GET_TEXT(MSG_OUTAGE_RECOVERY));
}
#if ENABLED(BACKUP_POWER_SUPPLY)
void PrintJobRecovery::raise_z() {
// Disable all heaters to reduce power loss
thermalManager.disable_all_heaters();
quickstop_stepper();
// Raise Z axis
gcode.process_subcommands_now_P(PSTR("G91\nG0 Z" STRINGIFY(POWER_LOSS_ZRAISE)));
planner.synchronize();
}
#endif
#endif
/**
@ -260,8 +287,6 @@ void PrintJobRecovery::write() {
*/
void PrintJobRecovery::resume() {
#define RECOVERY_ZRAISE 2
const uint32_t resume_sdpos = info.sdpos; // Get here before the stepper ISR overwrites it
#if HAS_LEVELING
@ -272,15 +297,27 @@ void PrintJobRecovery::resume() {
// Reset E, raise Z, home XY...
gcode.process_subcommands_now_P(PSTR("G92.9 E0"
#if Z_HOME_DIR > 0
// If Z homing goes to max, reset E and home all
"\nG28R0"
// If Z homing goes to max, just reset E and home all
"\n"
"G28R0"
#if ENABLED(MARLIN_DEV_MODE)
"S"
#endif
#else
#else // "G92.9 E0 ..."
// Set Z to 0, raise Z by RECOVERY_ZRAISE, and Home (XY only for Cartesian)
// with no raise. (Only do simulated homing in Marlin Dev Mode.)
"Z0\nG1Z" STRINGIFY(RECOVERY_ZRAISE) "\nG28R0"
#if ENABLED(BACKUP_POWER_SUPPLY)
"Z" STRINGIFY(POWER_LOSS_ZRAISE) // Z-axis was already raised at outage
#else
"Z0\n" // Set Z=0
"G1Z" STRINGIFY(POWER_LOSS_ZRAISE) // Raise Z
#endif
"\n"
"G28R0"
#if ENABLED(MARLIN_DEV_MODE)
"S"
#elif !IS_KINEMATIC

6
Marlin/src/feature/power_loss_recovery.h
View file

@ -168,7 +168,7 @@ class PrintJobRecovery {
#if PIN_EXISTS(POWER_LOSS)
static inline void outage() {
if (enabled && IS_SD_PRINTING() && READ(POWER_LOSS_PIN) == POWER_LOSS_STATE)
if (enabled && READ(POWER_LOSS_PIN) == POWER_LOSS_STATE)
_outage();
}
#endif
@ -184,6 +184,10 @@ class PrintJobRecovery {
private:
static void write();
#if ENABLED(BACKUP_POWER_SUPPLY)
static void raise_z();
#endif
#if PIN_EXISTS(POWER_LOSS)
static void _outage();
#endif

9
Marlin/src/gcode/feature/powerloss/M1000.cpp
View file

@ -52,8 +52,13 @@ inline void plr_error(PGM_P const prefix) {
void GcodeSuite::M1000() {
if (recovery.valid()) {
if (parser.seen('S'))
ui.goto_screen(menu_job_recovery);
if (parser.seen('S')) {
#if HAS_LCD_MENU
ui.goto_screen(menu_job_recovery);
#else
SERIAL_ECHO_MSG("Resume requires LCD.");
#endif
}
else
recovery.resume();
}

4
Marlin/src/inc/SanityCheck.h
View file

@ -2336,8 +2336,8 @@ static_assert( _ARR_TEST(3,0) && _ARR_TEST(3,1) && _ARR_TEST(3,2)
#endif
#endif
#if ENABLED(POWER_LOSS_RECOVERY) && DISABLED(ULTIPANEL)
#error "POWER_LOSS_RECOVERY currently requires an LCD Controller."
#if ENABLED(BACKUP_POWER_SUPPLY) && !PIN_EXISTS(POWER_LOSS)
#error "BACKUP_POWER_SUPPLY requires a POWER_LOSS_PIN."
#endif
#if ENABLED(Z_STEPPER_AUTO_ALIGN)

2
config/default/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/3DFabXYZ/Migbot/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/ADIMLab/Gantry v1/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 28 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/ADIMLab/Gantry v2/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/AlephObjects/TAZ4/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Alfawise/U20-bltouch/Configuration_adv.h
View file

@ -961,6 +961,8 @@
*/
#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Alfawise/U20/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/AliExpress/UM2pExt/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Anet/A2/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Anet/A2plus/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Anet/A6/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Anet/A8/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Anet/A8plus/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Anet/E16/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/AnyCubic/i3/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/ArmEd/Configuration_adv.h
View file

@ -964,6 +964,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/BIBO/TouchX/default/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/BQ/Hephestos/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/BQ/Hephestos_2/Configuration_adv.h
View file

@ -968,6 +968,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/BQ/WITBOX/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Cartesio/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Creality/CR-10/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Creality/CR-10S/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Creality/CR-10_5S/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Creality/CR-10mini/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Creality/CR-20 Pro/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Creality/CR-20/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Creality/CR-8/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Creality/Ender-2/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Creality/Ender-3/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Creality/Ender-4/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Creality/Ender-5/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Dagoma/Disco Ultimate/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Einstart-S/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/FYSETC/AIO_II/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/FYSETC/Cheetah/BLTouch/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/FYSETC/Cheetah/base/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/FYSETC/F6_13/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Felix/DUAL/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Felix/Single/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/FlashForge/CreatorPro/Configuration_adv.h
View file

@ -959,6 +959,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/FolgerTech/i3-2020/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Formbot/Raptor/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Formbot/T_Rex_2+/Configuration_adv.h
View file

@ -952,6 +952,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Formbot/T_Rex_3/Configuration_adv.h
View file

@ -964,6 +964,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Geeetech/A10/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Geeetech/A10M/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
#define POWER_LOSS_PIN 69 // Pin to detect power loss
#define POWER_LOSS_STATE LOW // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Geeetech/A20M/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
#define POWER_LOSS_PIN 69 // Pin to detect power loss
#define POWER_LOSS_STATE LOW // State of pin indicating power loss
#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Geeetech/MeCreator2/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/HMS434/Configuration_adv.h
View file

@ -945,6 +945,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume

2
config/examples/Infitary/i3-M508/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/JGAurora/A1/Configuration_adv.h
View file

@ -965,6 +965,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/JGAurora/A5/Configuration_adv.h
View file

@ -960,6 +960,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/JGAurora/A5S/Configuration_adv.h
View file

@ -965,6 +965,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/MakerParts/Configuration_adv.h
View file

@ -957,6 +957,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Malyan/M150/Configuration_adv.h
View file

@ -957,6 +957,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Malyan/M200/Configuration_adv.h
View file

@ -959,6 +959,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Micromake/C1/enhanced/Configuration_adv.h
View file

@ -957,6 +957,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Mks/Robin/Configuration_adv.h
View file

@ -957,6 +957,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Mks/Sbase/Configuration_adv.h
View file

@ -958,6 +958,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/RapideLite/RL200/Configuration_adv.h
View file

@ -957,6 +957,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/RigidBot/Configuration_adv.h
View file

@ -957,6 +957,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/SCARA/Configuration_adv.h
View file

@ -957,6 +957,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h
View file

@ -957,6 +957,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Sanguinololu/Configuration_adv.h
View file

@ -957,6 +957,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Tevo/Michelangelo/Configuration_adv.h
View file

@ -957,6 +957,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Tevo/Tarantula Pro/Configuration_adv.h
View file

@ -957,6 +957,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h
View file

@ -957,6 +957,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h
View file

@ -957,6 +957,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/TheBorg/Configuration_adv.h
View file

@ -957,6 +957,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/TinyBoy2/Configuration_adv.h
View file

@ -957,6 +957,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Tronxy/X3A/Configuration_adv.h
View file

@ -957,6 +957,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Tronxy/X5S-2E/Configuration_adv.h
View file

@ -957,6 +957,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/UltiMachine/Archim1/Configuration_adv.h
View file

@ -957,6 +957,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/UltiMachine/Archim2/Configuration_adv.h
View file

@ -957,6 +957,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/VORONDesign/Configuration_adv.h
View file

@ -957,6 +957,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Velleman/K8200/Configuration_adv.h
View file

@ -970,6 +970,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Velleman/K8400/Dual-head/Configuration_adv.h
View file

@ -957,6 +957,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Velleman/K8400/Single-head/Configuration_adv.h
View file

@ -957,6 +957,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/WASP/PowerWASP/Configuration_adv.h
View file

@ -957,6 +957,8 @@
*/
#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
#define POWER_LOSS_PIN 65 // Pin to detect power loss
#define POWER_LOSS_STATE LOW // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Wanhao/Duplicator 6/Configuration_adv.h
View file

@ -959,6 +959,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Wanhao/Duplicator i3 2.1/Configuration_adv.h
View file

@ -944,6 +944,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h
View file

@ -957,6 +957,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/delta/Anycubic/Kossel/Configuration_adv.h
View file

@ -962,6 +962,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/delta/Dreammaker/Overlord/Configuration_adv.h
View file

@ -962,6 +962,8 @@
*/
#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss (optional)
#define POWER_LOSS_STATE LOW // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h
View file

@ -962,6 +962,8 @@
*/
#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss (optional)
#define POWER_LOSS_STATE LOW // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h
View file

@ -962,6 +962,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

2
config/examples/delta/FLSUN/kossel/Configuration_adv.h
View file

@ -962,6 +962,8 @@
*/
//#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
//#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS)
//#define POWER_LOSS_PIN 44 // Pin to detect power loss
//#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate

Some files were not shown because too many files have changed in this diff Show more