Edit digipot currents via LCD, save to EEPROM
This commit is contained in:
dot-bob
Scott Lahteine
parent
3c7bfe798d
commit
b3c36c98fd
|
|
@ -36,13 +36,13 @@
|
|||
*
|
||||
*/
|
||||
|
||||
#define EEPROM_VERSION "V38"
|
||||
#define EEPROM_VERSION "V39"
|
||||
|
||||
// Change EEPROM version if these are changed:
|
||||
#define EEPROM_OFFSET 100
|
||||
|
||||
/**
|
||||
* V38 EEPROM Layout:
|
||||
* V39 EEPROM Layout:
|
||||
*
|
||||
* 100 Version (char x4)
|
||||
* 104 EEPROM CRC16 (uint16_t)
|
||||
|
|
@ -140,24 +140,29 @@
|
|||
* 534 M200 T D filament_size (float x5) (T0..3)
|
||||
*
|
||||
* HAVE_TMC2130: 20 bytes
|
||||
* 554 M906 X stepperX current (uint16_t)
|
||||
* 556 M906 Y stepperY current (uint16_t)
|
||||
* 558 M906 Z stepperZ current (uint16_t)
|
||||
* 560 M906 X2 stepperX2 current (uint16_t)
|
||||
* 562 M906 Y2 stepperY2 current (uint16_t)
|
||||
* 564 M906 Z2 stepperZ2 current (uint16_t)
|
||||
* 566 M906 E0 stepperE0 current (uint16_t)
|
||||
* 568 M906 E1 stepperE1 current (uint16_t)
|
||||
* 570 M906 E2 stepperE2 current (uint16_t)
|
||||
* 572 M906 E3 stepperE3 current (uint16_t)
|
||||
* 576 M906 E4 stepperE4 current (uint16_t)
|
||||
* 554 M906 X Stepper X current (uint16_t)
|
||||
* 556 M906 Y Stepper Y current (uint16_t)
|
||||
* 558 M906 Z Stepper Z current (uint16_t)
|
||||
* 560 M906 X2 Stepper X2 current (uint16_t)
|
||||
* 562 M906 Y2 Stepper Y2 current (uint16_t)
|
||||
* 564 M906 Z2 Stepper Z2 current (uint16_t)
|
||||
* 566 M906 E0 Stepper E0 current (uint16_t)
|
||||
* 568 M906 E1 Stepper E1 current (uint16_t)
|
||||
* 570 M906 E2 Stepper E2 current (uint16_t)
|
||||
* 572 M906 E3 Stepper E3 current (uint16_t)
|
||||
* 576 M906 E4 Stepper E4 current (uint16_t)
|
||||
*
|
||||
* LIN_ADVANCE: 8 bytes
|
||||
* 580 M900 K extruder_advance_k (float)
|
||||
* 584 M900 WHD advance_ed_ratio (float)
|
||||
*
|
||||
* 588 Minimum end-point
|
||||
* 1909 (588 + 36 + 9 + 288 + 988) Maximum end-point
|
||||
* HAS_MOTOR_CURRENT_PWM:
|
||||
* 588 M907 X Stepper XY current (uint32_t)
|
||||
* 592 M907 Z Stepper Z current (uint32_t)
|
||||
* 596 M907 E Stepper E current (uint32_t)
|
||||
*
|
||||
* 600 Minimum end-point
|
||||
* 1921 (600 + 36 + 9 + 288 + 988) Maximum end-point
|
||||
*
|
||||
* ========================================================================
|
||||
* meshes_begin (between max and min end-point, directly above)
|
||||
|
|
@ -177,6 +182,7 @@ MarlinSettings settings;
|
|||
#include "planner.h"
|
||||
#include "temperature.h"
|
||||
#include "ultralcd.h"
|
||||
#include "stepper.h"
|
||||
|
||||
#if ENABLED(INCH_MODE_SUPPORT) || (ENABLED(ULTIPANEL) && ENABLED(TEMPERATURE_UNITS_SUPPORT))
|
||||
#include "gcode.h"
|
||||
|
|
@ -238,6 +244,10 @@ void MarlinSettings::postprocess() {
|
|||
refresh_bed_level();
|
||||
//set_bed_leveling_enabled(leveling_is_on);
|
||||
#endif
|
||||
|
||||
#if HAS_MOTOR_CURRENT_PWM
|
||||
stepper.refresh_motor_power();
|
||||
#endif
|
||||
}
|
||||
|
||||
#if ENABLED(EEPROM_SETTINGS)
|
||||
|
|
@ -626,6 +636,13 @@ void MarlinSettings::postprocess() {
|
|||
EEPROM_WRITE(dummy);
|
||||
#endif
|
||||
|
||||
#if HAS_MOTOR_CURRENT_PWM
|
||||
for (uint8_t q = 3; q--;) EEPROM_WRITE(stepper.motor_current_setting[q]);
|
||||
#else
|
||||
const uint32_t dummyui32 = 0;
|
||||
for (uint8_t q = 3; q--;) EEPROM_WRITE(dummyui32);
|
||||
#endif
|
||||
|
||||
if (!eeprom_error) {
|
||||
const int eeprom_size = eeprom_index;
|
||||
|
||||
|
|
@ -979,6 +996,13 @@ void MarlinSettings::postprocess() {
|
|||
EEPROM_READ(dummy);
|
||||
#endif
|
||||
|
||||
#if HAS_MOTOR_CURRENT_PWM
|
||||
for (uint8_t q = 3; q--;) EEPROM_READ(stepper.motor_current_setting[q]);
|
||||
#else
|
||||
uint32_t dummyui32;
|
||||
for (uint8_t q = 3; q--;) EEPROM_READ(dummyui32);
|
||||
#endif
|
||||
|
||||
if (working_crc == stored_crc) {
|
||||
postprocess();
|
||||
SERIAL_ECHO_START();
|
||||
|
|
@ -1309,6 +1333,12 @@ void MarlinSettings::reset() {
|
|||
planner.advance_ed_ratio = LIN_ADVANCE_E_D_RATIO;
|
||||
#endif
|
||||
|
||||
#if HAS_MOTOR_CURRENT_PWM
|
||||
uint32_t tmp_motor_current_setting[3] = PWM_MOTOR_CURRENT;
|
||||
for (uint8_t q = 3; q--;)
|
||||
stepper.digipot_current(q, (stepper.motor_current_setting[q] = tmp_motor_current_setting[q]));
|
||||
#endif
|
||||
|
||||
#if ENABLED(AUTO_BED_LEVELING_UBL)
|
||||
ubl.reset();
|
||||
#endif
|
||||
|
|
@ -1788,6 +1818,18 @@ void MarlinSettings::reset() {
|
|||
SERIAL_ECHOPAIR(" M900 K", planner.extruder_advance_k);
|
||||
SERIAL_ECHOLNPAIR(" R", planner.advance_ed_ratio);
|
||||
#endif
|
||||
|
||||
#if HAS_MOTOR_CURRENT_PWM
|
||||
CONFIG_ECHO_START;
|
||||
if (!forReplay) {
|
||||
SERIAL_ECHOLNPGM("Stepper motor currents:");
|
||||
CONFIG_ECHO_START;
|
||||
}
|
||||
SERIAL_ECHOPAIR(" M907 X", stepper.motor_current_setting[0]);
|
||||
SERIAL_ECHOPAIR(" Z", stepper.motor_current_setting[1]);
|
||||
SERIAL_ECHOPAIR(" E", stepper.motor_current_setting[2]);
|
||||
SERIAL_EOL();
|
||||
#endif
|
||||
}
|
||||
|
||||
#endif // !DISABLE_M503
|
||||
|
|
|
|||
|
|
@ -85,7 +85,9 @@
|
|||
#define MOTOR_CURRENT_PWM_Z_PIN 45
|
||||
#define MOTOR_CURRENT_PWM_E_PIN 44
|
||||
// Motor current PWM conversion, PWM value = MotorCurrentSetting * 255 / range
|
||||
#ifndef MOTOR_CURRENT_PWM_RANGE
|
||||
#define MOTOR_CURRENT_PWM_RANGE 2000
|
||||
#endif
|
||||
#define DEFAULT_PWM_MOTOR_CURRENT {1300, 1300, 1250}
|
||||
|
||||
//
|
||||
|
|
|
|||
|
|
@ -74,7 +74,9 @@
|
|||
#define MOTOR_CURRENT_PWM_Z_PIN 45
|
||||
#define MOTOR_CURRENT_PWM_E_PIN 46
|
||||
// Motor current PWM conversion, PWM value = MotorCurrentSetting * 255 / range
|
||||
#ifndef MOTOR_CURRENT_PWM_RANGE
|
||||
#define MOTOR_CURRENT_PWM_RANGE 2000
|
||||
#endif
|
||||
#define DEFAULT_PWM_MOTOR_CURRENT {1300, 1300, 1250}
|
||||
|
||||
//
|
||||
|
|
|
|||
|
|
@ -72,6 +72,10 @@ block_t* Stepper::current_block = NULL; // A pointer to the block currently bei
|
|||
bool Stepper::performing_homing = false;
|
||||
#endif
|
||||
|
||||
#if HAS_MOTOR_CURRENT_PWM
|
||||
uint32_t Stepper::motor_current_setting[3] = PWM_MOTOR_CURRENT;
|
||||
#endif
|
||||
|
||||
// private:
|
||||
|
||||
uint8_t Stepper::last_direction_bits = 0; // The next stepping-bits to be output
|
||||
|
|
@ -1457,34 +1461,29 @@ void Stepper::report_positions() {
|
|||
|
||||
#endif // HAS_DIGIPOTSS
|
||||
|
||||
#if HAS_DIGIPOTSS || HAS_MOTOR_CURRENT_PWM
|
||||
#if HAS_MOTOR_CURRENT_PWM
|
||||
|
||||
void Stepper::digipot_init() {
|
||||
#if HAS_DIGIPOTSS
|
||||
static const uint8_t digipot_motor_current[] = DIGIPOT_MOTOR_CURRENT;
|
||||
SPI.begin();
|
||||
SET_OUTPUT(DIGIPOTSS_PIN);
|
||||
for (uint8_t i = 0; i < COUNT(digipot_motor_current); i++) {
|
||||
//digitalPotWrite(digipot_ch[i], digipot_motor_current[i]);
|
||||
digipot_current(i, digipot_motor_current[i]);
|
||||
}
|
||||
#elif HAS_MOTOR_CURRENT_PWM
|
||||
void Stepper::refresh_motor_power() {
|
||||
for (uint8_t i = 0; i < COUNT(motor_current_setting); ++i) {
|
||||
switch (i) {
|
||||
#if PIN_EXISTS(MOTOR_CURRENT_PWM_XY)
|
||||
SET_OUTPUT(MOTOR_CURRENT_PWM_XY_PIN);
|
||||
digipot_current(0, motor_current_setting[0]);
|
||||
case 0:
|
||||
#endif
|
||||
#if PIN_EXISTS(MOTOR_CURRENT_PWM_Z)
|
||||
SET_OUTPUT(MOTOR_CURRENT_PWM_Z_PIN);
|
||||
digipot_current(1, motor_current_setting[1]);
|
||||
case 1:
|
||||
#endif
|
||||
#if PIN_EXISTS(MOTOR_CURRENT_PWM_E)
|
||||
SET_OUTPUT(MOTOR_CURRENT_PWM_E_PIN);
|
||||
digipot_current(2, motor_current_setting[2]);
|
||||
#endif
|
||||
//Set timer5 to 31khz so the PWM of the motor power is as constant as possible. (removes a buzzing noise)
|
||||
TCCR5B = (TCCR5B & ~(_BV(CS50) | _BV(CS51) | _BV(CS52))) | _BV(CS50);
|
||||
case 2:
|
||||
#endif
|
||||
digipot_current(i, motor_current_setting[i]);
|
||||
default: break;
|
||||
}
|
||||
}
|
||||
}
|
||||
|
||||
#endif // HAS_MOTOR_CURRENT_PWM
|
||||
|
||||
#if HAS_DIGIPOTSS || HAS_MOTOR_CURRENT_PWM
|
||||
|
||||
void Stepper::digipot_current(const uint8_t driver, const int current) {
|
||||
|
||||
|
|
@ -1494,6 +1493,10 @@ void Stepper::report_positions() {
|
|||
digitalPotWrite(digipot_ch[driver], current);
|
||||
|
||||
#elif HAS_MOTOR_CURRENT_PWM
|
||||
|
||||
if (WITHIN(driver, 0, 2))
|
||||
motor_current_setting[driver] = current; // update motor_current_setting
|
||||
|
||||
#define _WRITE_CURRENT_PWM(P) analogWrite(MOTOR_CURRENT_PWM_## P ##_PIN, 255L * current / (MOTOR_CURRENT_PWM_RANGE))
|
||||
switch (driver) {
|
||||
#if PIN_EXISTS(MOTOR_CURRENT_PWM_XY)
|
||||
|
|
@ -1509,6 +1512,40 @@ void Stepper::report_positions() {
|
|||
#endif
|
||||
}
|
||||
|
||||
void Stepper::digipot_init() {
|
||||
|
||||
#if HAS_DIGIPOTSS
|
||||
|
||||
static const uint8_t digipot_motor_current[] = DIGIPOT_MOTOR_CURRENT;
|
||||
|
||||
SPI.begin();
|
||||
SET_OUTPUT(DIGIPOTSS_PIN);
|
||||
|
||||
for (uint8_t i = 0; i < COUNT(digipot_motor_current); i++) {
|
||||
//digitalPotWrite(digipot_ch[i], digipot_motor_current[i]);
|
||||
digipot_current(i, digipot_motor_current[i]);
|
||||
}
|
||||
|
||||
#elif HAS_MOTOR_CURRENT_PWM
|
||||
|
||||
#if PIN_EXISTS(MOTOR_CURRENT_PWM_XY)
|
||||
SET_OUTPUT(MOTOR_CURRENT_PWM_XY_PIN);
|
||||
#endif
|
||||
#if PIN_EXISTS(MOTOR_CURRENT_PWM_Z)
|
||||
SET_OUTPUT(MOTOR_CURRENT_PWM_Z_PIN);
|
||||
#endif
|
||||
#if PIN_EXISTS(MOTOR_CURRENT_PWM_E)
|
||||
SET_OUTPUT(MOTOR_CURRENT_PWM_E_PIN);
|
||||
#endif
|
||||
|
||||
refresh_motor_power();
|
||||
|
||||
// Set Timer5 to 31khz so the PWM of the motor power is as constant as possible. (removes a buzzing noise)
|
||||
SET_CS5(PRESCALER_1);
|
||||
|
||||
#endif
|
||||
}
|
||||
|
||||
#endif
|
||||
|
||||
#if HAS_MICROSTEPS
|
||||
|
|
|
|||
|
|
@ -91,6 +91,13 @@ class Stepper {
|
|||
static bool performing_homing;
|
||||
#endif
|
||||
|
||||
#if HAS_MOTOR_CURRENT_PWM
|
||||
#ifndef PWM_MOTOR_CURRENT
|
||||
#define PWM_MOTOR_CURRENT DEFAULT_PWM_MOTOR_CURRENT
|
||||
#endif
|
||||
static uint32_t motor_current_setting[3];
|
||||
#endif
|
||||
|
||||
private:
|
||||
|
||||
static uint8_t last_direction_bits; // The next stepping-bits to be output
|
||||
|
|
@ -132,13 +139,6 @@ class Stepper {
|
|||
static volatile long endstops_trigsteps[XYZ];
|
||||
static volatile long endstops_stepsTotal, endstops_stepsDone;
|
||||
|
||||
#if HAS_MOTOR_CURRENT_PWM
|
||||
#ifndef PWM_MOTOR_CURRENT
|
||||
#define PWM_MOTOR_CURRENT DEFAULT_PWM_MOTOR_CURRENT
|
||||
#endif
|
||||
static constexpr int motor_current_setting[3] = PWM_MOTOR_CURRENT;
|
||||
#endif
|
||||
|
||||
//
|
||||
// Positions of stepper motors, in step units
|
||||
//
|
||||
|
|
@ -279,6 +279,10 @@ class Stepper {
|
|||
return endstops_trigsteps[axis] * planner.steps_to_mm[axis];
|
||||
}
|
||||
|
||||
#if HAS_MOTOR_CURRENT_PWM
|
||||
static void refresh_motor_power();
|
||||
#endif
|
||||
|
||||
private:
|
||||
|
||||
static FORCE_INLINE unsigned short calc_timer(unsigned short step_rate) {
|
||||
|
|
@ -380,7 +384,9 @@ class Stepper {
|
|||
// SERIAL_ECHOLN(current_block->final_advance/256.0);
|
||||
}
|
||||
|
||||
#if HAS_DIGIPOTSS || HAS_MOTOR_CURRENT_PWM
|
||||
static void digipot_init();
|
||||
#endif
|
||||
|
||||
#if HAS_MICROSTEPS
|
||||
static void microstep_init();
|
||||
|
|
|
|||
|
|
@ -1249,6 +1249,7 @@ void kill_screen(const char* lcd_msg) {
|
|||
*
|
||||
*/
|
||||
#if ENABLED(DAC_STEPPER_CURRENT)
|
||||
|
||||
void dac_driver_getValues() { LOOP_XYZE(i) driverPercent[i] = dac_current_get_percent((AxisEnum)i); }
|
||||
|
||||
void dac_driver_commit() { dac_current_set_percents(driverPercent); }
|
||||
|
|
@ -1266,7 +1267,27 @@ void kill_screen(const char* lcd_msg) {
|
|||
MENU_ITEM(function, MSG_DAC_EEPROM_WRITE, dac_driver_eeprom_write);
|
||||
END_MENU();
|
||||
}
|
||||
|
||||
#endif // DAC_STEPPER_CURRENT
|
||||
|
||||
#if HAS_MOTOR_CURRENT_PWM
|
||||
|
||||
void lcd_pwm_menu() {
|
||||
START_MENU();
|
||||
MENU_BACK(MSG_CONTROL);
|
||||
#if PIN_EXISTS(MOTOR_CURRENT_PWM_XY)
|
||||
MENU_ITEM_EDIT_CALLBACK(long5, MSG_X MSG_Y, &stepper.motor_current_setting[0], 100, 2000, Stepper::refresh_motor_power);
|
||||
#endif
|
||||
#if PIN_EXISTS(MOTOR_CURRENT_PWM_Z)
|
||||
MENU_ITEM_EDIT_CALLBACK(long5, MSG_Z, &stepper.motor_current_setting[1], 100, 2000, Stepper::refresh_motor_power);
|
||||
#endif
|
||||
#if PIN_EXISTS(MOTOR_CURRENT_PWM_E)
|
||||
MENU_ITEM_EDIT_CALLBACK(long5, MSG_E, &stepper.motor_current_setting[2], 100, 2000, Stepper::refresh_motor_power);
|
||||
#endif
|
||||
END_MENU();
|
||||
}
|
||||
|
||||
#endif // HAS_MOTOR_CURRENT_PWM
|
||||
|
||||
constexpr int16_t heater_maxtemp[HOTENDS] = ARRAY_BY_HOTENDS(HEATER_0_MAXTEMP, HEATER_1_MAXTEMP, HEATER_2_MAXTEMP, HEATER_3_MAXTEMP, HEATER_4_MAXTEMP);
|
||||
|
||||
|
|
@ -2894,6 +2915,9 @@ void kill_screen(const char* lcd_msg) {
|
|||
#if ENABLED(DAC_STEPPER_CURRENT)
|
||||
MENU_ITEM(submenu, MSG_DRIVE_STRENGTH, lcd_dac_menu);
|
||||
#endif
|
||||
#if HAS_MOTOR_CURRENT_PWM
|
||||
MENU_ITEM(submenu, MSG_DRIVE_STRENGTH, lcd_pwm_menu);
|
||||
#endif
|
||||
|
||||
#if ENABLED(BLTOUCH)
|
||||
MENU_ITEM(submenu, MSG_BLTOUCH, bltouch_menu);
|
||||
|
|
|
|||
Loading…
Reference in a new issue