Merge pull request #408 from STB3/Marlin_with_ATmega1284p_Sanguino_on_023_support
Marlin with ATmega1284p sanguino support under Arduino 023
This commit is contained in:
daid
commit
b3ebb71704
|
|
@ -14,3 +14,86 @@ sanguino.bootloader.lock_bits=0x0F
|
|||
sanguino.build.mcu=atmega644p
|
||||
sanguino.build.f_cpu=16000000L
|
||||
sanguino.build.core=arduino
|
||||
|
||||
##############################################################
|
||||
|
||||
atmega644.name=Sanguino W/ ATmega644P
|
||||
|
||||
atmega644.upload.protocol=stk500
|
||||
atmega644.upload.maximum_size=63488
|
||||
atmega644.upload.speed=57600
|
||||
|
||||
atmega644.bootloader.low_fuses=0xFF
|
||||
atmega644.bootloader.high_fuses=0x9A
|
||||
atmega644.bootloader.extended_fuses=0xFF
|
||||
atmega644.bootloader.path=atmega
|
||||
atmega644.bootloader.file=ATmegaBOOT_168_atmega644p.hex
|
||||
#atmega644.bootloader.file=ATmegaBOOT_644P.hex
|
||||
atmega644.bootloader.unlock_bits=0x3F
|
||||
atmega644.bootloader.lock_bits=0x0F
|
||||
|
||||
atmega644.build.mcu=atmega644p
|
||||
atmega644.build.f_cpu=16000000L
|
||||
atmega644.build.core=arduino
|
||||
|
||||
##############################################################
|
||||
|
||||
atmega12848m.name=Sanguino W/ ATmega1284p 8mhz
|
||||
|
||||
atmega12848m.upload.protocol=stk500
|
||||
atmega12848m.upload.maximum_size=131072
|
||||
atmega12848m.upload.speed=19200
|
||||
|
||||
atmega12848m.bootloader.low_fuses=0xFD
|
||||
atmega12848m.bootloader.high_fuses=0x9A
|
||||
atmega12848m.bootloader.extended_fuses=0xFF
|
||||
atmega12848m.bootloader.path=atmega
|
||||
atmega12848m.bootloader.file=ATmegaBOOT_168_atmega1284p_8m.hex
|
||||
atmega12848m.bootloader.unlock_bits=0x3F
|
||||
atmega12848m.bootloader.lock_bits=0x0F
|
||||
|
||||
atmega12848m.build.mcu=atmega1284p
|
||||
atmega12848m.build.f_cpu=8000000L
|
||||
atmega12848m.build.core=arduino
|
||||
|
||||
##############################################################
|
||||
|
||||
atmega1284.name=Sanguino W/ ATmega1284p 16mhz
|
||||
|
||||
atmega1284.upload.protocol=stk500
|
||||
atmega1284.upload.maximum_size=131072
|
||||
atmega1284.upload.speed=57600
|
||||
|
||||
atmega1284.bootloader.low_fuses=0xFF
|
||||
atmega1284.bootloader.high_fuses=0x9A
|
||||
atmega1284.bootloader.extended_fuses=0xFF
|
||||
atmega1284.bootloader.path=atmega
|
||||
atmega1284.bootloader.file=ATmegaBOOT_168_atmega1284p.hex
|
||||
atmega1284.bootloader.unlock_bits=0x3F
|
||||
atmega1284.bootloader.lock_bits=0x0F
|
||||
|
||||
atmega1284.build.mcu=atmega1284p
|
||||
atmega1284.build.f_cpu=16000000L
|
||||
atmega1284.build.core=arduino
|
||||
|
||||
|
||||
##############################################################
|
||||
|
||||
atmega1284s.name=Sanguino W/ ATmega1284p 20mhz
|
||||
|
||||
atmega1284s.upload.protocol=stk500
|
||||
atmega1284s.upload.maximum_size=131072
|
||||
atmega1284s.upload.speed=57600
|
||||
|
||||
atmega1284s.bootloader.low_fuses=0xFF
|
||||
atmega1284s.bootloader.high_fuses=0x9A
|
||||
atmega1284s.bootloader.extended_fuses=0xFF
|
||||
atmega1284s.bootloader.path=atmega
|
||||
atmega1284s.bootloader.file=ATmegaBOOT_168_atmega1284p.hex
|
||||
atmega1284s.bootloader.unlock_bits=0x3F
|
||||
atmega1284s.bootloader.lock_bits=0x0F
|
||||
|
||||
atmega1284s.build.mcu=atmega1284p
|
||||
atmega1284s.build.f_cpu=20000000L
|
||||
atmega1284s.build.core=arduino
|
||||
#
|
||||
|
|
|
|||
|
|
@ -0,0 +1,470 @@
|
|||
# Makefile for ATmegaBOOT
|
||||
# E.Lins, 18.7.2005
|
||||
# $Id$
|
||||
#
|
||||
# Instructions
|
||||
#
|
||||
# To make bootloader .hex file:
|
||||
# make diecimila
|
||||
# make lilypad
|
||||
# make ng
|
||||
# etc...
|
||||
#
|
||||
# To burn bootloader .hex file:
|
||||
# make diecimila_isp
|
||||
# make lilypad_isp
|
||||
# make ng_isp
|
||||
# etc...
|
||||
|
||||
# program name should not be changed...
|
||||
PROGRAM = optiboot
|
||||
|
||||
# The default behavior is to build using tools that are in the users
|
||||
# current path variables, but we can also build using an installed
|
||||
# Arduino user IDE setup, or the Arduino source tree.
|
||||
# Uncomment this next lines to build within the arduino environment,
|
||||
# using the arduino-included avrgcc toolset (mac and pc)
|
||||
# ENV ?= arduino
|
||||
# ENV ?= arduinodev
|
||||
# OS ?= macosx
|
||||
# OS ?= windows
|
||||
|
||||
|
||||
# enter the parameters for the avrdude isp tool
|
||||
ISPTOOL = stk500v2
|
||||
ISPPORT = usb
|
||||
ISPSPEED = -b 115200
|
||||
|
||||
MCU_TARGET = atmega168
|
||||
LDSECTIONS = -Wl,--section-start=.text=0x3e00 -Wl,--section-start=.version=0x3ffe
|
||||
|
||||
# Build environments
|
||||
# Start of some ugly makefile-isms to allow optiboot to be built
|
||||
# in several different environments. See the README.TXT file for
|
||||
# details.
|
||||
|
||||
# default
|
||||
fixpath = $(1)
|
||||
|
||||
ifeq ($(ENV), arduino)
|
||||
# For Arduino, we assume that we're connected to the optiboot directory
|
||||
# included with the arduino distribution, which means that the full set
|
||||
# of avr-tools are "right up there" in standard places.
|
||||
TOOLROOT = ../../../tools
|
||||
GCCROOT = $(TOOLROOT)/avr/bin/
|
||||
AVRDUDE_CONF = -C$(TOOLROOT)/avr/etc/avrdude.conf
|
||||
|
||||
ifeq ($(OS), windows)
|
||||
# On windows, SOME of the tool paths will need to have backslashes instead
|
||||
# of forward slashes (because they use windows cmd.exe for execution instead
|
||||
# of a unix/mingw shell?) We also have to ensure that a consistent shell
|
||||
# is used even if a unix shell is installed (ie as part of WINAVR)
|
||||
fixpath = $(subst /,\,$1)
|
||||
SHELL = cmd.exe
|
||||
endif
|
||||
|
||||
else ifeq ($(ENV), arduinodev)
|
||||
# Arduino IDE source code environment. Use the unpacked compilers created
|
||||
# by the build (you'll need to do "ant build" first.)
|
||||
ifeq ($(OS), macosx)
|
||||
TOOLROOT = ../../../../build/macosx/work/Arduino.app/Contents/Resources/Java/hardware/tools
|
||||
endif
|
||||
ifeq ($(OS), windows)
|
||||
TOOLROOT = ../../../../build/windows/work/hardware/tools
|
||||
endif
|
||||
|
||||
GCCROOT = $(TOOLROOT)/avr/bin/
|
||||
AVRDUDE_CONF = -C$(TOOLROOT)/avr/etc/avrdude.conf
|
||||
|
||||
else
|
||||
GCCROOT =
|
||||
AVRDUDE_CONF =
|
||||
endif
|
||||
#
|
||||
# End of build environment code.
|
||||
|
||||
|
||||
# the efuse should really be 0xf8; since, however, only the lower
|
||||
# three bits of that byte are used on the atmega168, avrdude gets
|
||||
# confused if you specify 1's for the higher bits, see:
|
||||
# http://tinker.it/now/2007/02/24/the-tale-of-avrdude-atmega168-and-extended-bits-fuses/
|
||||
#
|
||||
# similarly, the lock bits should be 0xff instead of 0x3f (to
|
||||
# unlock the bootloader section) and 0xcf instead of 0x2f (to
|
||||
# lock it), but since the high two bits of the lock byte are
|
||||
# unused, avrdude would get confused.
|
||||
|
||||
ISPFUSES = $(GCCROOT)avrdude $(AVRDUDE_CONF) -c $(ISPTOOL) \
|
||||
-p $(MCU_TARGET) -P $(ISPPORT) $(ISPSPEED) \
|
||||
-e -u -U lock:w:0x3f:m -U efuse:w:0x$(EFUSE):m \
|
||||
-U hfuse:w:0x$(HFUSE):m -U lfuse:w:0x$(LFUSE):m
|
||||
ISPFLASH = $(GCCROOT)avrdude $(AVRDUDE_CONF) -c $(ISPTOOL) \
|
||||
-p $(MCU_TARGET) -P $(ISPPORT) $(ISPSPEED) \
|
||||
-U flash:w:$(PROGRAM)_$(TARGET).hex -U lock:w:0x2f:m
|
||||
|
||||
STK500 = "C:\Program Files\Atmel\AVR Tools\STK500\Stk500.exe"
|
||||
STK500-1 = $(STK500) -e -d$(MCU_TARGET) -pf -vf -if$(PROGRAM)_$(TARGET).hex \
|
||||
-lFF -LFF -f$(HFUSE)$(LFUSE) -EF8 -ms -q -cUSB -I200kHz -s -wt
|
||||
STK500-2 = $(STK500) -d$(MCU_TARGET) -ms -q -lCF -LCF -cUSB -I200kHz -s -wt
|
||||
|
||||
OBJ = $(PROGRAM).o
|
||||
OPTIMIZE = -Os -fno-inline-small-functions -fno-split-wide-types -mshort-calls
|
||||
|
||||
DEFS =
|
||||
LIBS =
|
||||
|
||||
CC = $(GCCROOT)avr-gcc
|
||||
|
||||
# Override is only needed by avr-lib build system.
|
||||
|
||||
override CFLAGS = -g -Wall $(OPTIMIZE) -mmcu=$(MCU_TARGET) -DF_CPU=$(AVR_FREQ) $(DEFS)
|
||||
override LDFLAGS = $(LDSECTIONS) -Wl,--relax -Wl,--gc-sections -nostartfiles -nostdlib
|
||||
|
||||
OBJCOPY = $(GCCROOT)avr-objcopy
|
||||
OBJDUMP = $(call fixpath,$(GCCROOT)avr-objdump)
|
||||
|
||||
SIZE = $(GCCROOT)avr-size
|
||||
|
||||
# Test platforms
|
||||
# Virtual boot block test
|
||||
virboot328: TARGET = atmega328
|
||||
virboot328: MCU_TARGET = atmega328p
|
||||
virboot328: CFLAGS += '-DLED_START_FLASHES=3' '-DBAUD_RATE=115200' '-DVIRTUAL_BOOT'
|
||||
virboot328: AVR_FREQ = 16000000L
|
||||
virboot328: LDSECTIONS = -Wl,--section-start=.text=0x7e00 -Wl,--section-start=.version=0x7ffe
|
||||
virboot328: $(PROGRAM)_atmega328.hex
|
||||
virboot328: $(PROGRAM)_atmega328.lst
|
||||
|
||||
# 20MHz clocked platforms
|
||||
#
|
||||
# These are capable of 230400 baud, or 115200 baud on PC (Arduino Avrdude issue)
|
||||
#
|
||||
|
||||
pro20: TARGET = pro_20mhz
|
||||
pro20: MCU_TARGET = atmega168
|
||||
pro20: CFLAGS += '-DLED_START_FLASHES=3' '-DBAUD_RATE=115200'
|
||||
pro20: AVR_FREQ = 20000000L
|
||||
pro20: $(PROGRAM)_pro_20mhz.hex
|
||||
pro20: $(PROGRAM)_pro_20mhz.lst
|
||||
|
||||
pro20_isp: pro20
|
||||
pro20_isp: TARGET = pro_20mhz
|
||||
# 2.7V brownout
|
||||
pro20_isp: HFUSE = DD
|
||||
# Full swing xtal (20MHz) 258CK/14CK+4.1ms
|
||||
pro20_isp: LFUSE = C6
|
||||
# 512 byte boot
|
||||
pro20_isp: EFUSE = 04
|
||||
pro20_isp: isp
|
||||
|
||||
# 16MHz clocked platforms
|
||||
#
|
||||
# These are capable of 230400 baud, or 115200 baud on PC (Arduino Avrdude issue)
|
||||
#
|
||||
|
||||
pro16: TARGET = pro_16MHz
|
||||
pro16: MCU_TARGET = atmega168
|
||||
pro16: CFLAGS += '-DLED_START_FLASHES=3' '-DBAUD_RATE=115200'
|
||||
pro16: AVR_FREQ = 16000000L
|
||||
pro16: $(PROGRAM)_pro_16MHz.hex
|
||||
pro16: $(PROGRAM)_pro_16MHz.lst
|
||||
|
||||
pro16_isp: pro16
|
||||
pro16_isp: TARGET = pro_16MHz
|
||||
# 2.7V brownout
|
||||
pro16_isp: HFUSE = DD
|
||||
# Full swing xtal (20MHz) 258CK/14CK+4.1ms
|
||||
pro16_isp: LFUSE = C6
|
||||
# 512 byte boot
|
||||
pro16_isp: EFUSE = 04
|
||||
pro16_isp: isp
|
||||
|
||||
# Diecimila, Duemilanove with m168, and NG use identical bootloaders
|
||||
# Call it "atmega168" for generality and clarity, keep "diecimila" for
|
||||
# backward compatibility of makefile
|
||||
#
|
||||
atmega168: TARGET = atmega168
|
||||
atmega168: MCU_TARGET = atmega168
|
||||
atmega168: CFLAGS += '-DLED_START_FLASHES=3' '-DBAUD_RATE=115200'
|
||||
atmega168: AVR_FREQ = 16000000L
|
||||
atmega168: $(PROGRAM)_atmega168.hex
|
||||
atmega168: $(PROGRAM)_atmega168.lst
|
||||
|
||||
atmega168_isp: atmega168
|
||||
atmega168_isp: TARGET = atmega168
|
||||
# 2.7V brownout
|
||||
atmega168_isp: HFUSE = DD
|
||||
# Low power xtal (16MHz) 16KCK/14CK+65ms
|
||||
atmega168_isp: LFUSE = FF
|
||||
# 512 byte boot
|
||||
atmega168_isp: EFUSE = 04
|
||||
atmega168_isp: isp
|
||||
|
||||
diecimila: TARGET = diecimila
|
||||
diecimila: MCU_TARGET = atmega168
|
||||
diecimila: CFLAGS += '-DLED_START_FLASHES=3' '-DBAUD_RATE=115200'
|
||||
diecimila: AVR_FREQ = 16000000L
|
||||
diecimila: $(PROGRAM)_diecimila.hex
|
||||
diecimila: $(PROGRAM)_diecimila.lst
|
||||
|
||||
diecimila_isp: diecimila
|
||||
diecimila_isp: TARGET = diecimila
|
||||
# 2.7V brownout
|
||||
diecimila_isp: HFUSE = DD
|
||||
# Low power xtal (16MHz) 16KCK/14CK+65ms
|
||||
diecimila_isp: LFUSE = FF
|
||||
# 512 byte boot
|
||||
diecimila_isp: EFUSE = 04
|
||||
diecimila_isp: isp
|
||||
|
||||
atmega328: TARGET = atmega328
|
||||
atmega328: MCU_TARGET = atmega328p
|
||||
atmega328: CFLAGS += '-DLED_START_FLASHES=3' '-DBAUD_RATE=115200'
|
||||
atmega328: AVR_FREQ = 16000000L
|
||||
atmega328: LDSECTIONS = -Wl,--section-start=.text=0x7e00 -Wl,--section-start=.version=0x7ffe
|
||||
atmega328: $(PROGRAM)_atmega328.hex
|
||||
atmega328: $(PROGRAM)_atmega328.lst
|
||||
|
||||
atmega328_isp: atmega328
|
||||
atmega328_isp: TARGET = atmega328
|
||||
atmega328_isp: MCU_TARGET = atmega328p
|
||||
# 512 byte boot, SPIEN
|
||||
atmega328_isp: HFUSE = DE
|
||||
# Low power xtal (16MHz) 16KCK/14CK+65ms
|
||||
atmega328_isp: LFUSE = FF
|
||||
# 2.7V brownout
|
||||
atmega328_isp: EFUSE = 05
|
||||
atmega328_isp: isp
|
||||
|
||||
atmega1284: TARGET = atmega1284p
|
||||
atmega1284: MCU_TARGET = atmega1284p
|
||||
atmega1284: CFLAGS += '-DLED_START_FLASHES=3' '-DBAUD_RATE=115200' '-DBIGBOOT'
|
||||
atmega1284: AVR_FREQ = 16000000L
|
||||
atmega1284: LDSECTIONS = -Wl,--section-start=.text=0x1fc00
|
||||
atmega1284: $(PROGRAM)_atmega1284p.hex
|
||||
atmega1284: $(PROGRAM)_atmega1284p.lst
|
||||
|
||||
atmega1284_isp: atmega1284
|
||||
atmega1284_isp: TARGET = atmega1284p
|
||||
atmega1284_isp: MCU_TARGET = atmega1284p
|
||||
# 1024 byte boot
|
||||
atmega1284_isp: HFUSE = DE
|
||||
# Low power xtal (16MHz) 16KCK/14CK+65ms
|
||||
atmega1284_isp: LFUSE = FF
|
||||
# 2.7V brownout
|
||||
atmega1284_isp: EFUSE = FD
|
||||
atmega1284_isp: isp
|
||||
|
||||
# Sanguino has a minimum boot size of 1024 bytes, so enable extra functions
|
||||
#
|
||||
sanguino: TARGET = atmega644p
|
||||
sanguino: MCU_TARGET = atmega644p
|
||||
sanguino: CFLAGS += '-DLED_START_FLASHES=3' '-DBAUD_RATE=115200' '-DBIGBOOT'
|
||||
sanguino: AVR_FREQ = 16000000L
|
||||
sanguino: LDSECTIONS = -Wl,--section-start=.text=0xfc00
|
||||
sanguino: $(PROGRAM)_atmega644p.hex
|
||||
sanguino: $(PROGRAM)_atmega644p.lst
|
||||
|
||||
sanguino_isp: sanguino
|
||||
sanguino_isp: TARGET = atmega644p
|
||||
sanguino_isp: MCU_TARGET = atmega644p
|
||||
# 1024 byte boot
|
||||
sanguino_isp: HFUSE = DE
|
||||
# Low power xtal (16MHz) 16KCK/14CK+65ms
|
||||
sanguino_isp: LFUSE = FF
|
||||
# 2.7V brownout
|
||||
sanguino_isp: EFUSE = 05
|
||||
sanguino_isp: isp
|
||||
|
||||
# Mega has a minimum boot size of 1024 bytes, so enable extra functions
|
||||
#mega: TARGET = atmega1280
|
||||
mega: MCU_TARGET = atmega1280
|
||||
mega: CFLAGS += '-DLED_START_FLASHES=3' '-DBAUD_RATE=115200' '-DBIGBOOT'
|
||||
mega: AVR_FREQ = 16000000L
|
||||
mega: LDSECTIONS = -Wl,--section-start=.text=0x1fc00
|
||||
mega: $(PROGRAM)_atmega1280.hex
|
||||
mega: $(PROGRAM)_atmega1280.lst
|
||||
|
||||
mega_isp: mega
|
||||
mega_isp: TARGET = atmega1280
|
||||
mega_isp: MCU_TARGET = atmega1280
|
||||
# 1024 byte boot
|
||||
mega_isp: HFUSE = DE
|
||||
# Low power xtal (16MHz) 16KCK/14CK+65ms
|
||||
mega_isp: LFUSE = FF
|
||||
# 2.7V brownout
|
||||
mega_isp: EFUSE = 05
|
||||
mega_isp: isp
|
||||
|
||||
# ATmega8
|
||||
#
|
||||
atmega8: TARGET = atmega8
|
||||
atmega8: MCU_TARGET = atmega8
|
||||
atmega8: CFLAGS += '-DLED_START_FLASHES=3' '-DBAUD_RATE=115200'
|
||||
atmega8: AVR_FREQ = 16000000L
|
||||
atmega8: LDSECTIONS = -Wl,--section-start=.text=0x1e00 -Wl,--section-start=.version=0x1ffe
|
||||
atmega8: $(PROGRAM)_atmega8.hex
|
||||
atmega8: $(PROGRAM)_atmega8.lst
|
||||
|
||||
atmega8_isp: atmega8
|
||||
atmega8_isp: TARGET = atmega8
|
||||
atmega8_isp: MCU_TARGET = atmega8
|
||||
# SPIEN, CKOPT, Bootsize=512B
|
||||
atmega8_isp: HFUSE = CC
|
||||
# 2.7V brownout, Low power xtal (16MHz) 16KCK/14CK+65ms
|
||||
atmega8_isp: LFUSE = BF
|
||||
atmega8_isp: isp
|
||||
|
||||
# ATmega88
|
||||
#
|
||||
atmega88: TARGET = atmega88
|
||||
atmega88: MCU_TARGET = atmega88
|
||||
atmega88: CFLAGS += '-DLED_START_FLASHES=3' '-DBAUD_RATE=115200'
|
||||
atmega88: AVR_FREQ = 16000000L
|
||||
atmega88: LDSECTIONS = -Wl,--section-start=.text=0x1e00 -Wl,--section-start=.version=0x1ffe
|
||||
atmega88: $(PROGRAM)_atmega88.hex
|
||||
atmega88: $(PROGRAM)_atmega88.lst
|
||||
|
||||
atmega88_isp: atmega88
|
||||
atmega88_isp: TARGET = atmega88
|
||||
atmega88_isp: MCU_TARGET = atmega88
|
||||
# 2.7V brownout
|
||||
atmega88_isp: HFUSE = DD
|
||||
# Low power xtal (16MHz) 16KCK/14CK+65ms
|
||||
atemga88_isp: LFUSE = FF
|
||||
# 512 byte boot
|
||||
atmega88_isp: EFUSE = 04
|
||||
atmega88_isp: isp
|
||||
|
||||
|
||||
# 8MHz clocked platforms
|
||||
#
|
||||
# These are capable of 115200 baud
|
||||
#
|
||||
|
||||
lilypad: TARGET = lilypad
|
||||
lilypad: MCU_TARGET = atmega168
|
||||
lilypad: CFLAGS += '-DLED_START_FLASHES=3' '-DBAUD_RATE=115200'
|
||||
lilypad: AVR_FREQ = 8000000L
|
||||
lilypad: $(PROGRAM)_lilypad.hex
|
||||
lilypad: $(PROGRAM)_lilypad.lst
|
||||
|
||||
lilypad_isp: lilypad
|
||||
lilypad_isp: TARGET = lilypad
|
||||
# 2.7V brownout
|
||||
lilypad_isp: HFUSE = DD
|
||||
# Internal 8MHz osc (8MHz) Slow rising power
|
||||
lilypad_isp: LFUSE = E2
|
||||
# 512 byte boot
|
||||
lilypad_isp: EFUSE = 04
|
||||
lilypad_isp: isp
|
||||
|
||||
lilypad_resonator: TARGET = lilypad_resonator
|
||||
lilypad_resonator: MCU_TARGET = atmega168
|
||||
lilypad_resonator: CFLAGS += '-DLED_START_FLASHES=3' '-DBAUD_RATE=115200'
|
||||
lilypad_resonator: AVR_FREQ = 8000000L
|
||||
lilypad_resonator: $(PROGRAM)_lilypad_resonator.hex
|
||||
lilypad_resonator: $(PROGRAM)_lilypad_resonator.lst
|
||||
|
||||
lilypad_resonator_isp: lilypad_resonator
|
||||
lilypad_resonator_isp: TARGET = lilypad_resonator
|
||||
# 2.7V brownout
|
||||
lilypad_resonator_isp: HFUSE = DD
|
||||
# Full swing xtal (20MHz) 258CK/14CK+4.1ms
|
||||
lilypad_resonator_isp: LFUSE = C6
|
||||
# 512 byte boot
|
||||
lilypad_resonator_isp: EFUSE = 04
|
||||
lilypad_resonator_isp: isp
|
||||
|
||||
pro8: TARGET = pro_8MHz
|
||||
pro8: MCU_TARGET = atmega168
|
||||
pro8: CFLAGS += '-DLED_START_FLASHES=3' '-DBAUD_RATE=115200'
|
||||
pro8: AVR_FREQ = 8000000L
|
||||
pro8: $(PROGRAM)_pro_8MHz.hex
|
||||
pro8: $(PROGRAM)_pro_8MHz.lst
|
||||
|
||||
pro8_isp: pro8
|
||||
pro8_isp: TARGET = pro_8MHz
|
||||
# 2.7V brownout
|
||||
pro8_isp: HFUSE = DD
|
||||
# Full swing xtal (20MHz) 258CK/14CK+4.1ms
|
||||
pro8_isp: LFUSE = C6
|
||||
# 512 byte boot
|
||||
pro8_isp: EFUSE = 04
|
||||
pro8_isp: isp
|
||||
|
||||
atmega328_pro8: TARGET = atmega328_pro_8MHz
|
||||
atmega328_pro8: MCU_TARGET = atmega328p
|
||||
atmega328_pro8: CFLAGS += '-DLED_START_FLASHES=3' '-DBAUD_RATE=115200'
|
||||
atmega328_pro8: AVR_FREQ = 8000000L
|
||||
atmega328_pro8: LDSECTIONS = -Wl,--section-start=.text=0x7e00 -Wl,--section-start=.version=0x7ffe
|
||||
atmega328_pro8: $(PROGRAM)_atmega328_pro_8MHz.hex
|
||||
atmega328_pro8: $(PROGRAM)_atmega328_pro_8MHz.lst
|
||||
|
||||
atmega328_pro8_isp: atmega328_pro8
|
||||
atmega328_pro8_isp: TARGET = atmega328_pro_8MHz
|
||||
atmega328_pro8_isp: MCU_TARGET = atmega328p
|
||||
# 512 byte boot, SPIEN
|
||||
atmega328_pro8_isp: HFUSE = DE
|
||||
# Low power xtal (16MHz) 16KCK/14CK+65ms
|
||||
atmega328_pro8_isp: LFUSE = FF
|
||||
# 2.7V brownout
|
||||
atmega328_pro8_isp: EFUSE = 05
|
||||
atmega328_pro8_isp: isp
|
||||
|
||||
# 1MHz clocked platforms
|
||||
#
|
||||
# These are capable of 9600 baud
|
||||
#
|
||||
|
||||
luminet: TARGET = luminet
|
||||
luminet: MCU_TARGET = attiny84
|
||||
luminet: CFLAGS += '-DLED_START_FLASHES=3' '-DSOFT_UART' '-DBAUD_RATE=9600'
|
||||
luminet: CFLAGS += '-DVIRTUAL_BOOT_PARTITION'
|
||||
luminet: AVR_FREQ = 1000000L
|
||||
luminet: LDSECTIONS = -Wl,--section-start=.text=0x1d00 -Wl,--section-start=.version=0x1efe
|
||||
luminet: $(PROGRAM)_luminet.hex
|
||||
luminet: $(PROGRAM)_luminet.lst
|
||||
|
||||
luminet_isp: luminet
|
||||
luminet_isp: TARGET = luminet
|
||||
luminet_isp: MCU_TARGET = attiny84
|
||||
# Brownout disabled
|
||||
luminet_isp: HFUSE = DF
|
||||
# 1MHz internal oscillator, slowly rising power
|
||||
luminet_isp: LFUSE = 62
|
||||
# Self-programming enable
|
||||
luminet_isp: EFUSE = FE
|
||||
luminet_isp: isp
|
||||
|
||||
#
|
||||
# Generic build instructions
|
||||
#
|
||||
#
|
||||
|
||||
isp: $(TARGET)
|
||||
$(ISPFUSES)
|
||||
$(ISPFLASH)
|
||||
|
||||
isp-stk500: $(PROGRAM)_$(TARGET).hex
|
||||
$(STK500-1)
|
||||
$(STK500-2)
|
||||
|
||||
%.elf: $(OBJ)
|
||||
$(CC) $(CFLAGS) $(LDFLAGS) -o $@ $^ $(LIBS)
|
||||
$(SIZE) $@
|
||||
|
||||
clean:
|
||||
rm -rf *.o *.elf *.lst *.map *.sym *.lss *.eep *.srec *.bin *.hex
|
||||
|
||||
%.lst: %.elf
|
||||
$(OBJDUMP) -h -S $< > $@
|
||||
|
||||
%.hex: %.elf
|
||||
$(OBJCOPY) -j .text -j .data -j .version --set-section-flags .version=alloc,load -O ihex $< $@
|
||||
|
||||
%.srec: %.elf
|
||||
$(OBJCOPY) -j .text -j .data -j .version --set-section-flags .version=alloc,load -O srec $< $@
|
||||
|
||||
%.bin: %.elf
|
||||
$(OBJCOPY) -j .text -j .data -j .version --set-section-flags .version=alloc,load -O binary $< $@
|
||||
|
|
@ -0,0 +1,848 @@
|
|||
/* Modified to use out for SPM access
|
||||
** Peter Knight, Optiboot project http://optiboot.googlecode.com
|
||||
**
|
||||
** Todo: Tidy up
|
||||
**
|
||||
** "_short" routines execute 1 cycle faster and use 1 less word of flash
|
||||
** by using "out" instruction instead of "sts".
|
||||
**
|
||||
** Additional elpm variants that trust the value of RAMPZ
|
||||
*/
|
||||
|
||||
/* Copyright (c) 2002, 2003, 2004, 2005, 2006, 2007 Eric B. Weddington
|
||||
All rights reserved.
|
||||
|
||||
Redistribution and use in source and binary forms, with or without
|
||||
modification, are permitted provided that the following conditions are met:
|
||||
|
||||
* Redistributions of source code must retain the above copyright
|
||||
notice, this list of conditions and the following disclaimer.
|
||||
* Redistributions in binary form must reproduce the above copyright
|
||||
notice, this list of conditions and the following disclaimer in
|
||||
the documentation and/or other materials provided with the
|
||||
distribution.
|
||||
* Neither the name of the copyright holders nor the names of
|
||||
contributors may be used to endorse or promote products derived
|
||||
from this software without specific prior written permission.
|
||||
|
||||
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
|
||||
AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
||||
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
|
||||
ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE
|
||||
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
|
||||
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
|
||||
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
|
||||
INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
|
||||
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
|
||||
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
POSSIBILITY OF SUCH DAMAGE. */
|
||||
|
||||
/* $Id: boot.h,v 1.27.2.3 2008/09/30 13:58:48 arcanum Exp $ */
|
||||
|
||||
#ifndef _AVR_BOOT_H_
|
||||
#define _AVR_BOOT_H_ 1
|
||||
|
||||
/** \file */
|
||||
/** \defgroup avr_boot <avr/boot.h>: Bootloader Support Utilities
|
||||
\code
|
||||
#include <avr/io.h>
|
||||
#include <avr/boot.h>
|
||||
\endcode
|
||||
|
||||
The macros in this module provide a C language interface to the
|
||||
bootloader support functionality of certain AVR processors. These
|
||||
macros are designed to work with all sizes of flash memory.
|
||||
|
||||
Global interrupts are not automatically disabled for these macros. It
|
||||
is left up to the programmer to do this. See the code example below.
|
||||
Also see the processor datasheet for caveats on having global interrupts
|
||||
enabled during writing of the Flash.
|
||||
|
||||
\note Not all AVR processors provide bootloader support. See your
|
||||
processor datasheet to see if it provides bootloader support.
|
||||
|
||||
\todo From email with Marek: On smaller devices (all except ATmega64/128),
|
||||
__SPM_REG is in the I/O space, accessible with the shorter "in" and "out"
|
||||
instructions - since the boot loader has a limited size, this could be an
|
||||
important optimization.
|
||||
|
||||
\par API Usage Example
|
||||
The following code shows typical usage of the boot API.
|
||||
|
||||
\code
|
||||
#include <inttypes.h>
|
||||
#include <avr/interrupt.h>
|
||||
#include <avr/pgmspace.h>
|
||||
|
||||
void boot_program_page (uint32_t page, uint8_t *buf)
|
||||
{
|
||||
uint16_t i;
|
||||
uint8_t sreg;
|
||||
|
||||
// Disable interrupts.
|
||||
|
||||
sreg = SREG;
|
||||
cli();
|
||||
|
||||
eeprom_busy_wait ();
|
||||
|
||||
boot_page_erase (page);
|
||||
boot_spm_busy_wait (); // Wait until the memory is erased.
|
||||
|
||||
for (i=0; i<SPM_PAGESIZE; i+=2)
|
||||
{
|
||||
// Set up little-endian word.
|
||||
|
||||
uint16_t w = *buf++;
|
||||
w += (*buf++) << 8;
|
||||
|
||||
boot_page_fill (page + i, w);
|
||||
}
|
||||
|
||||
boot_page_write (page); // Store buffer in flash page.
|
||||
boot_spm_busy_wait(); // Wait until the memory is written.
|
||||
|
||||
// Reenable RWW-section again. We need this if we want to jump back
|
||||
// to the application after bootloading.
|
||||
|
||||
boot_rww_enable ();
|
||||
|
||||
// Re-enable interrupts (if they were ever enabled).
|
||||
|
||||
SREG = sreg;
|
||||
}\endcode */
|
||||
|
||||
#include <avr/eeprom.h>
|
||||
#include <avr/io.h>
|
||||
#include <inttypes.h>
|
||||
#include <limits.h>
|
||||
|
||||
/* Check for SPM Control Register in processor. */
|
||||
#if defined (SPMCSR)
|
||||
# define __SPM_REG SPMCSR
|
||||
#elif defined (SPMCR)
|
||||
# define __SPM_REG SPMCR
|
||||
#else
|
||||
# error AVR processor does not provide bootloader support!
|
||||
#endif
|
||||
|
||||
|
||||
/* Check for SPM Enable bit. */
|
||||
#if defined(SPMEN)
|
||||
# define __SPM_ENABLE SPMEN
|
||||
#elif defined(SELFPRGEN)
|
||||
# define __SPM_ENABLE SELFPRGEN
|
||||
#else
|
||||
# error Cannot find SPM Enable bit definition!
|
||||
#endif
|
||||
|
||||
/** \ingroup avr_boot
|
||||
\def BOOTLOADER_SECTION
|
||||
|
||||
Used to declare a function or variable to be placed into a
|
||||
new section called .bootloader. This section and its contents
|
||||
can then be relocated to any address (such as the bootloader
|
||||
NRWW area) at link-time. */
|
||||
|
||||
#define BOOTLOADER_SECTION __attribute__ ((section (".bootloader")))
|
||||
|
||||
/* Create common bit definitions. */
|
||||
#ifdef ASB
|
||||
#define __COMMON_ASB ASB
|
||||
#else
|
||||
#define __COMMON_ASB RWWSB
|
||||
#endif
|
||||
|
||||
#ifdef ASRE
|
||||
#define __COMMON_ASRE ASRE
|
||||
#else
|
||||
#define __COMMON_ASRE RWWSRE
|
||||
#endif
|
||||
|
||||
/* Define the bit positions of the Boot Lock Bits. */
|
||||
|
||||
#define BLB12 5
|
||||
#define BLB11 4
|
||||
#define BLB02 3
|
||||
#define BLB01 2
|
||||
|
||||
/** \ingroup avr_boot
|
||||
\def boot_spm_interrupt_enable()
|
||||
Enable the SPM interrupt. */
|
||||
|
||||
#define boot_spm_interrupt_enable() (__SPM_REG |= (uint8_t)_BV(SPMIE))
|
||||
|
||||
/** \ingroup avr_boot
|
||||
\def boot_spm_interrupt_disable()
|
||||
Disable the SPM interrupt. */
|
||||
|
||||
#define boot_spm_interrupt_disable() (__SPM_REG &= (uint8_t)~_BV(SPMIE))
|
||||
|
||||
/** \ingroup avr_boot
|
||||
\def boot_is_spm_interrupt()
|
||||
Check if the SPM interrupt is enabled. */
|
||||
|
||||
#define boot_is_spm_interrupt() (__SPM_REG & (uint8_t)_BV(SPMIE))
|
||||
|
||||
/** \ingroup avr_boot
|
||||
\def boot_rww_busy()
|
||||
Check if the RWW section is busy. */
|
||||
|
||||
#define boot_rww_busy() (__SPM_REG & (uint8_t)_BV(__COMMON_ASB))
|
||||
|
||||
/** \ingroup avr_boot
|
||||
\def boot_spm_busy()
|
||||
Check if the SPM instruction is busy. */
|
||||
|
||||
#define boot_spm_busy() (__SPM_REG & (uint8_t)_BV(__SPM_ENABLE))
|
||||
|
||||
/** \ingroup avr_boot
|
||||
\def boot_spm_busy_wait()
|
||||
Wait while the SPM instruction is busy. */
|
||||
|
||||
#define boot_spm_busy_wait() do{}while(boot_spm_busy())
|
||||
|
||||
#define __BOOT_PAGE_ERASE (_BV(__SPM_ENABLE) | _BV(PGERS))
|
||||
#define __BOOT_PAGE_WRITE (_BV(__SPM_ENABLE) | _BV(PGWRT))
|
||||
#define __BOOT_PAGE_FILL _BV(__SPM_ENABLE)
|
||||
#define __BOOT_RWW_ENABLE (_BV(__SPM_ENABLE) | _BV(__COMMON_ASRE))
|
||||
#define __BOOT_LOCK_BITS_SET (_BV(__SPM_ENABLE) | _BV(BLBSET))
|
||||
|
||||
#define __boot_page_fill_short(address, data) \
|
||||
(__extension__({ \
|
||||
__asm__ __volatile__ \
|
||||
( \
|
||||
"movw r0, %3\n\t" \
|
||||
"out %0, %1\n\t" \
|
||||
"spm\n\t" \
|
||||
"clr r1\n\t" \
|
||||
: \
|
||||
: "i" (_SFR_IO_ADDR(__SPM_REG)), \
|
||||
"r" ((uint8_t)__BOOT_PAGE_FILL), \
|
||||
"z" ((uint16_t)address), \
|
||||
"r" ((uint16_t)data) \
|
||||
: "r0" \
|
||||
); \
|
||||
}))
|
||||
|
||||
#define __boot_page_fill_normal(address, data) \
|
||||
(__extension__({ \
|
||||
__asm__ __volatile__ \
|
||||
( \
|
||||
"movw r0, %3\n\t" \
|
||||
"sts %0, %1\n\t" \
|
||||
"spm\n\t" \
|
||||
"clr r1\n\t" \
|
||||
: \
|
||||
: "i" (_SFR_MEM_ADDR(__SPM_REG)), \
|
||||
"r" ((uint8_t)__BOOT_PAGE_FILL), \
|
||||
"z" ((uint16_t)address), \
|
||||
"r" ((uint16_t)data) \
|
||||
: "r0" \
|
||||
); \
|
||||
}))
|
||||
|
||||
#define __boot_page_fill_alternate(address, data)\
|
||||
(__extension__({ \
|
||||
__asm__ __volatile__ \
|
||||
( \
|
||||
"movw r0, %3\n\t" \
|
||||
"sts %0, %1\n\t" \
|
||||
"spm\n\t" \
|
||||
".word 0xffff\n\t" \
|
||||
"nop\n\t" \
|
||||
"clr r1\n\t" \
|
||||
: \
|
||||
: "i" (_SFR_MEM_ADDR(__SPM_REG)), \
|
||||
"r" ((uint8_t)__BOOT_PAGE_FILL), \
|
||||
"z" ((uint16_t)address), \
|
||||
"r" ((uint16_t)data) \
|
||||
: "r0" \
|
||||
); \
|
||||
}))
|
||||
|
||||
#define __boot_page_fill_extended(address, data) \
|
||||
(__extension__({ \
|
||||
__asm__ __volatile__ \
|
||||
( \
|
||||
"movw r0, %4\n\t" \
|
||||
"movw r30, %A3\n\t" \
|
||||
"sts %1, %C3\n\t" \
|
||||
"sts %0, %2\n\t" \
|
||||
"spm\n\t" \
|
||||
"clr r1\n\t" \
|
||||
: \
|
||||
: "i" (_SFR_MEM_ADDR(__SPM_REG)), \
|
||||
"i" (_SFR_MEM_ADDR(RAMPZ)), \
|
||||
"r" ((uint8_t)__BOOT_PAGE_FILL), \
|
||||
"r" ((uint32_t)address), \
|
||||
"r" ((uint16_t)data) \
|
||||
: "r0", "r30", "r31" \
|
||||
); \
|
||||
}))
|
||||
|
||||
#define __boot_page_fill_extended_short(address, data) \
|
||||
(__extension__({ \
|
||||
__asm__ __volatile__ \
|
||||
( \
|
||||
"movw r0, %4\n\t" \
|
||||
"movw r30, %A3\n\t" \
|
||||
"out %1, %C3\n\t" \
|
||||
"out %0, %2\n\t" \
|
||||
"spm\n\t" \
|
||||
"clr r1\n\t" \
|
||||
: \
|
||||
: "i" (_SFR_IO_ADDR(__SPM_REG)), \
|
||||
"i" (_SFR_IO_ADDR(RAMPZ)), \
|
||||
"r" ((uint8_t)__BOOT_PAGE_FILL), \
|
||||
"r" ((uint32_t)address), \
|
||||
"r" ((uint16_t)data) \
|
||||
: "r0", "r30", "r31" \
|
||||
); \
|
||||
}))
|
||||
|
||||
#define __boot_page_erase_short(address) \
|
||||
(__extension__({ \
|
||||
__asm__ __volatile__ \
|
||||
( \
|
||||
"out %0, %1\n\t" \
|
||||
"spm\n\t" \
|
||||
: \
|
||||
: "i" (_SFR_IO_ADDR(__SPM_REG)), \
|
||||
"r" ((uint8_t)__BOOT_PAGE_ERASE), \
|
||||
"z" ((uint16_t)address) \
|
||||
); \
|
||||
}))
|
||||
|
||||
|
||||
#define __boot_page_erase_normal(address) \
|
||||
(__extension__({ \
|
||||
__asm__ __volatile__ \
|
||||
( \
|
||||
"sts %0, %1\n\t" \
|
||||
"spm\n\t" \
|
||||
: \
|
||||
: "i" (_SFR_MEM_ADDR(__SPM_REG)), \
|
||||
"r" ((uint8_t)__BOOT_PAGE_ERASE), \
|
||||
"z" ((uint16_t)address) \
|
||||
); \
|
||||
}))
|
||||
|
||||
#define __boot_page_erase_alternate(address) \
|
||||
(__extension__({ \
|
||||
__asm__ __volatile__ \
|
||||
( \
|
||||
"sts %0, %1\n\t" \
|
||||
"spm\n\t" \
|
||||
".word 0xffff\n\t" \
|
||||
"nop\n\t" \
|
||||
: \
|
||||
: "i" (_SFR_MEM_ADDR(__SPM_REG)), \
|
||||
"r" ((uint8_t)__BOOT_PAGE_ERASE), \
|
||||
"z" ((uint16_t)address) \
|
||||
); \
|
||||
}))
|
||||
|
||||
#define __boot_page_erase_extended(address) \
|
||||
(__extension__({ \
|
||||
__asm__ __volatile__ \
|
||||
( \
|
||||
"movw r30, %A3\n\t" \
|
||||
"sts %1, %C3\n\t" \
|
||||
"sts %0, %2\n\t" \
|
||||
"spm\n\t" \
|
||||
: \
|
||||
: "i" (_SFR_MEM_ADDR(__SPM_REG)), \
|
||||
"i" (_SFR_MEM_ADDR(RAMPZ)), \
|
||||
"r" ((uint8_t)__BOOT_PAGE_ERASE), \
|
||||
"r" ((uint32_t)address) \
|
||||
: "r30", "r31" \
|
||||
); \
|
||||
}))
|
||||
#define __boot_page_erase_extended_short(address) \
|
||||
(__extension__({ \
|
||||
__asm__ __volatile__ \
|
||||
( \
|
||||
"movw r30, %A3\n\t" \
|
||||
"out %1, %C3\n\t" \
|
||||
"out %0, %2\n\t" \
|
||||
"spm\n\t" \
|
||||
: \
|
||||
: "i" (_SFR_IO_ADDR(__SPM_REG)), \
|
||||
"i" (_SFR_IO_ADDR(RAMPZ)), \
|
||||
"r" ((uint8_t)__BOOT_PAGE_ERASE), \
|
||||
"r" ((uint32_t)address) \
|
||||
: "r30", "r31" \
|
||||
); \
|
||||
}))
|
||||
|
||||
#define __boot_page_write_short(address) \
|
||||
(__extension__({ \
|
||||
__asm__ __volatile__ \
|
||||
( \
|
||||
"out %0, %1\n\t" \
|
||||
"spm\n\t" \
|
||||
: \
|
||||
: "i" (_SFR_IO_ADDR(__SPM_REG)), \
|
||||
"r" ((uint8_t)__BOOT_PAGE_WRITE), \
|
||||
"z" ((uint16_t)address) \
|
||||
); \
|
||||
}))
|
||||
|
||||
#define __boot_page_write_normal(address) \
|
||||
(__extension__({ \
|
||||
__asm__ __volatile__ \
|
||||
( \
|
||||
"sts %0, %1\n\t" \
|
||||
"spm\n\t" \
|
||||
: \
|
||||
: "i" (_SFR_MEM_ADDR(__SPM_REG)), \
|
||||
"r" ((uint8_t)__BOOT_PAGE_WRITE), \
|
||||
"z" ((uint16_t)address) \
|
||||
); \
|
||||
}))
|
||||
|
||||
#define __boot_page_write_alternate(address) \
|
||||
(__extension__({ \
|
||||
__asm__ __volatile__ \
|
||||
( \
|
||||
"sts %0, %1\n\t" \
|
||||
"spm\n\t" \
|
||||
".word 0xffff\n\t" \
|
||||
"nop\n\t" \
|
||||
: \
|
||||
: "i" (_SFR_MEM_ADDR(__SPM_REG)), \
|
||||
"r" ((uint8_t)__BOOT_PAGE_WRITE), \
|
||||
"z" ((uint16_t)address) \
|
||||
); \
|
||||
}))
|
||||
|
||||
#define __boot_page_write_extended(address) \
|
||||
(__extension__({ \
|
||||
__asm__ __volatile__ \
|
||||
( \
|
||||
"movw r30, %A3\n\t" \
|
||||
"sts %1, %C3\n\t" \
|
||||
"sts %0, %2\n\t" \
|
||||
"spm\n\t" \
|
||||
: \
|
||||
: "i" (_SFR_MEM_ADDR(__SPM_REG)), \
|
||||
"i" (_SFR_MEM_ADDR(RAMPZ)), \
|
||||
"r" ((uint8_t)__BOOT_PAGE_WRITE), \
|
||||
"r" ((uint32_t)address) \
|
||||
: "r30", "r31" \
|
||||
); \
|
||||
}))
|
||||
#define __boot_page_write_extended_short(address) \
|
||||
(__extension__({ \
|
||||
__asm__ __volatile__ \
|
||||
( \
|
||||
"movw r30, %A3\n\t" \
|
||||
"out %1, %C3\n\t" \
|
||||
"out %0, %2\n\t" \
|
||||
"spm\n\t" \
|
||||
: \
|
||||
: "i" (_SFR_IO_ADDR(__SPM_REG)), \
|
||||
"i" (_SFR_IO_ADDR(RAMPZ)), \
|
||||
"r" ((uint8_t)__BOOT_PAGE_WRITE), \
|
||||
"r" ((uint32_t)address) \
|
||||
: "r30", "r31" \
|
||||
); \
|
||||
}))
|
||||
|
||||
#define __boot_rww_enable_short() \
|
||||
(__extension__({ \
|
||||
__asm__ __volatile__ \
|
||||
( \
|
||||
"out %0, %1\n\t" \
|
||||
"spm\n\t" \
|
||||
: \
|
||||
: "i" (_SFR_IO_ADDR(__SPM_REG)), \
|
||||
"r" ((uint8_t)__BOOT_RWW_ENABLE) \
|
||||
); \
|
||||
}))
|
||||
|
||||
#define __boot_rww_enable() \
|
||||
(__extension__({ \
|
||||
__asm__ __volatile__ \
|
||||
( \
|
||||
"sts %0, %1\n\t" \
|
||||
"spm\n\t" \
|
||||
: \
|
||||
: "i" (_SFR_MEM_ADDR(__SPM_REG)), \
|
||||
"r" ((uint8_t)__BOOT_RWW_ENABLE) \
|
||||
); \
|
||||
}))
|
||||
|
||||
#define __boot_rww_enable_alternate() \
|
||||
(__extension__({ \
|
||||
__asm__ __volatile__ \
|
||||
( \
|
||||
"sts %0, %1\n\t" \
|
||||
"spm\n\t" \
|
||||
".word 0xffff\n\t" \
|
||||
"nop\n\t" \
|
||||
: \
|
||||
: "i" (_SFR_MEM_ADDR(__SPM_REG)), \
|
||||
"r" ((uint8_t)__BOOT_RWW_ENABLE) \
|
||||
); \
|
||||
}))
|
||||
|
||||
/* From the mega16/mega128 data sheets (maybe others):
|
||||
|
||||
Bits by SPM To set the Boot Loader Lock bits, write the desired data to
|
||||
R0, write "X0001001" to SPMCR and execute SPM within four clock cycles
|
||||
after writing SPMCR. The only accessible Lock bits are the Boot Lock bits
|
||||
that may prevent the Application and Boot Loader section from any
|
||||
software update by the MCU.
|
||||
|
||||
If bits 5..2 in R0 are cleared (zero), the corresponding Boot Lock bit
|
||||
will be programmed if an SPM instruction is executed within four cycles
|
||||
after BLBSET and SPMEN (or SELFPRGEN) are set in SPMCR. The Z-pointer is
|
||||
don't care during this operation, but for future compatibility it is
|
||||
recommended to load the Z-pointer with $0001 (same as used for reading the
|
||||
Lock bits). For future compatibility It is also recommended to set bits 7,
|
||||
6, 1, and 0 in R0 to 1 when writing the Lock bits. When programming the
|
||||
Lock bits the entire Flash can be read during the operation. */
|
||||
|
||||
#define __boot_lock_bits_set_short(lock_bits) \
|
||||
(__extension__({ \
|
||||
uint8_t value = (uint8_t)(~(lock_bits)); \
|
||||
__asm__ __volatile__ \
|
||||
( \
|
||||
"ldi r30, 1\n\t" \
|
||||
"ldi r31, 0\n\t" \
|
||||
"mov r0, %2\n\t" \
|
||||
"out %0, %1\n\t" \
|
||||
"spm\n\t" \
|
||||
: \
|
||||
: "i" (_SFR_IO_ADDR(__SPM_REG)), \
|
||||
"r" ((uint8_t)__BOOT_LOCK_BITS_SET), \
|
||||
"r" (value) \
|
||||
: "r0", "r30", "r31" \
|
||||
); \
|
||||
}))
|
||||
|
||||
#define __boot_lock_bits_set(lock_bits) \
|
||||
(__extension__({ \
|
||||
uint8_t value = (uint8_t)(~(lock_bits)); \
|
||||
__asm__ __volatile__ \
|
||||
( \
|
||||
"ldi r30, 1\n\t" \
|
||||
"ldi r31, 0\n\t" \
|
||||
"mov r0, %2\n\t" \
|
||||
"sts %0, %1\n\t" \
|
||||
"spm\n\t" \
|
||||
: \
|
||||
: "i" (_SFR_MEM_ADDR(__SPM_REG)), \
|
||||
"r" ((uint8_t)__BOOT_LOCK_BITS_SET), \
|
||||
"r" (value) \
|
||||
: "r0", "r30", "r31" \
|
||||
); \
|
||||
}))
|
||||
|
||||
#define __boot_lock_bits_set_alternate(lock_bits) \
|
||||
(__extension__({ \
|
||||
uint8_t value = (uint8_t)(~(lock_bits)); \
|
||||
__asm__ __volatile__ \
|
||||
( \
|
||||
"ldi r30, 1\n\t" \
|
||||
"ldi r31, 0\n\t" \
|
||||
"mov r0, %2\n\t" \
|
||||
"sts %0, %1\n\t" \
|
||||
"spm\n\t" \
|
||||
".word 0xffff\n\t" \
|
||||
"nop\n\t" \
|
||||
: \
|
||||
: "i" (_SFR_MEM_ADDR(__SPM_REG)), \
|
||||
"r" ((uint8_t)__BOOT_LOCK_BITS_SET), \
|
||||
"r" (value) \
|
||||
: "r0", "r30", "r31" \
|
||||
); \
|
||||
}))
|
||||
|
||||
/*
|
||||
Reading lock and fuse bits:
|
||||
|
||||
Similarly to writing the lock bits above, set BLBSET and SPMEN (or
|
||||
SELFPRGEN) bits in __SPMREG, and then (within four clock cycles) issue an
|
||||
LPM instruction.
|
||||
|
||||
Z address: contents:
|
||||
0x0000 low fuse bits
|
||||
0x0001 lock bits
|
||||
0x0002 extended fuse bits
|
||||
0x0003 high fuse bits
|
||||
|
||||
Sounds confusing, doesn't it?
|
||||
|
||||
Unlike the macros in pgmspace.h, no need to care for non-enhanced
|
||||
cores here as these old cores do not provide SPM support anyway.
|
||||
*/
|
||||
|
||||
/** \ingroup avr_boot
|
||||
\def GET_LOW_FUSE_BITS
|
||||
address to read the low fuse bits, using boot_lock_fuse_bits_get
|
||||
*/
|
||||
#define GET_LOW_FUSE_BITS (0x0000)
|
||||
/** \ingroup avr_boot
|
||||
\def GET_LOCK_BITS
|
||||
address to read the lock bits, using boot_lock_fuse_bits_get
|
||||
*/
|
||||
#define GET_LOCK_BITS (0x0001)
|
||||
/** \ingroup avr_boot
|
||||
\def GET_EXTENDED_FUSE_BITS
|
||||
address to read the extended fuse bits, using boot_lock_fuse_bits_get
|
||||
*/
|
||||
#define GET_EXTENDED_FUSE_BITS (0x0002)
|
||||
/** \ingroup avr_boot
|
||||
\def GET_HIGH_FUSE_BITS
|
||||
address to read the high fuse bits, using boot_lock_fuse_bits_get
|
||||
*/
|
||||
#define GET_HIGH_FUSE_BITS (0x0003)
|
||||
|
||||
/** \ingroup avr_boot
|
||||
\def boot_lock_fuse_bits_get(address)
|
||||
|
||||
Read the lock or fuse bits at \c address.
|
||||
|
||||
Parameter \c address can be any of GET_LOW_FUSE_BITS,
|
||||
GET_LOCK_BITS, GET_EXTENDED_FUSE_BITS, or GET_HIGH_FUSE_BITS.
|
||||
|
||||
\note The lock and fuse bits returned are the physical values,
|
||||
i.e. a bit returned as 0 means the corresponding fuse or lock bit
|
||||
is programmed.
|
||||
*/
|
||||
#define boot_lock_fuse_bits_get_short(address) \
|
||||
(__extension__({ \
|
||||
uint8_t __result; \
|
||||
__asm__ __volatile__ \
|
||||
( \
|
||||
"ldi r30, %3\n\t" \
|
||||
"ldi r31, 0\n\t" \
|
||||
"out %1, %2\n\t" \
|
||||
"lpm %0, Z\n\t" \
|
||||
: "=r" (__result) \
|
||||
: "i" (_SFR_IO_ADDR(__SPM_REG)), \
|
||||
"r" ((uint8_t)__BOOT_LOCK_BITS_SET), \
|
||||
"M" (address) \
|
||||
: "r0", "r30", "r31" \
|
||||
); \
|
||||
__result; \
|
||||
}))
|
||||
|
||||
#define boot_lock_fuse_bits_get(address) \
|
||||
(__extension__({ \
|
||||
uint8_t __result; \
|
||||
__asm__ __volatile__ \
|
||||
( \
|
||||
"ldi r30, %3\n\t" \
|
||||
"ldi r31, 0\n\t" \
|
||||
"sts %1, %2\n\t" \
|
||||
"lpm %0, Z\n\t" \
|
||||
: "=r" (__result) \
|
||||
: "i" (_SFR_MEM_ADDR(__SPM_REG)), \
|
||||
"r" ((uint8_t)__BOOT_LOCK_BITS_SET), \
|
||||
"M" (address) \
|
||||
: "r0", "r30", "r31" \
|
||||
); \
|
||||
__result; \
|
||||
}))
|
||||
|
||||
/** \ingroup avr_boot
|
||||
\def boot_signature_byte_get(address)
|
||||
|
||||
Read the Signature Row byte at \c address. For some MCU types,
|
||||
this function can also retrieve the factory-stored oscillator
|
||||
calibration bytes.
|
||||
|
||||
Parameter \c address can be 0-0x1f as documented by the datasheet.
|
||||
\note The values are MCU type dependent.
|
||||
*/
|
||||
|
||||
#define __BOOT_SIGROW_READ (_BV(__SPM_ENABLE) | _BV(SIGRD))
|
||||
|
||||
#define boot_signature_byte_get_short(addr) \
|
||||
(__extension__({ \
|
||||
uint16_t __addr16 = (uint16_t)(addr); \
|
||||
uint8_t __result; \
|
||||
__asm__ __volatile__ \
|
||||
( \
|
||||
"out %1, %2\n\t" \
|
||||
"lpm %0, Z" "\n\t" \
|
||||
: "=r" (__result) \
|
||||
: "i" (_SFR_IO_ADDR(__SPM_REG)), \
|
||||
"r" ((uint8_t) __BOOT_SIGROW_READ), \
|
||||
"z" (__addr16) \
|
||||
); \
|
||||
__result; \
|
||||
}))
|
||||
|
||||
#define boot_signature_byte_get(addr) \
|
||||
(__extension__({ \
|
||||
uint16_t __addr16 = (uint16_t)(addr); \
|
||||
uint8_t __result; \
|
||||
__asm__ __volatile__ \
|
||||
( \
|
||||
"sts %1, %2\n\t" \
|
||||
"lpm %0, Z" "\n\t" \
|
||||
: "=r" (__result) \
|
||||
: "i" (_SFR_MEM_ADDR(__SPM_REG)), \
|
||||
"r" ((uint8_t) __BOOT_SIGROW_READ), \
|
||||
"z" (__addr16) \
|
||||
); \
|
||||
__result; \
|
||||
}))
|
||||
|
||||
/** \ingroup avr_boot
|
||||
\def boot_page_fill(address, data)
|
||||
|
||||
Fill the bootloader temporary page buffer for flash
|
||||
address with data word.
|
||||
|
||||
\note The address is a byte address. The data is a word. The AVR
|
||||
writes data to the buffer a word at a time, but addresses the buffer
|
||||
per byte! So, increment your address by 2 between calls, and send 2
|
||||
data bytes in a word format! The LSB of the data is written to the lower
|
||||
address; the MSB of the data is written to the higher address.*/
|
||||
|
||||
/** \ingroup avr_boot
|
||||
\def boot_page_erase(address)
|
||||
|
||||
Erase the flash page that contains address.
|
||||
|
||||
\note address is a byte address in flash, not a word address. */
|
||||
|
||||
/** \ingroup avr_boot
|
||||
\def boot_page_write(address)
|
||||
|
||||
Write the bootloader temporary page buffer
|
||||
to flash page that contains address.
|
||||
|
||||
\note address is a byte address in flash, not a word address. */
|
||||
|
||||
/** \ingroup avr_boot
|
||||
\def boot_rww_enable()
|
||||
|
||||
Enable the Read-While-Write memory section. */
|
||||
|
||||
/** \ingroup avr_boot
|
||||
\def boot_lock_bits_set(lock_bits)
|
||||
|
||||
Set the bootloader lock bits.
|
||||
|
||||
\param lock_bits A mask of which Boot Loader Lock Bits to set.
|
||||
|
||||
\note In this context, a 'set bit' will be written to a zero value.
|
||||
Note also that only BLBxx bits can be programmed by this command.
|
||||
|
||||
For example, to disallow the SPM instruction from writing to the Boot
|
||||
Loader memory section of flash, you would use this macro as such:
|
||||
|
||||
\code
|
||||
boot_lock_bits_set (_BV (BLB11));
|
||||
\endcode
|
||||
|
||||
\note Like any lock bits, the Boot Loader Lock Bits, once set,
|
||||
cannot be cleared again except by a chip erase which will in turn
|
||||
also erase the boot loader itself. */
|
||||
|
||||
/* Normal versions of the macros use 16-bit addresses.
|
||||
Extended versions of the macros use 32-bit addresses.
|
||||
Alternate versions of the macros use 16-bit addresses and require special
|
||||
instruction sequences after LPM.
|
||||
|
||||
FLASHEND is defined in the ioXXXX.h file.
|
||||
USHRT_MAX is defined in <limits.h>. */
|
||||
|
||||
#if defined(__AVR_ATmega161__) || defined(__AVR_ATmega163__) \
|
||||
|| defined(__AVR_ATmega323__)
|
||||
|
||||
/* Alternate: ATmega161/163/323 and 16 bit address */
|
||||
#define boot_page_fill(address, data) __boot_page_fill_alternate(address, data)
|
||||
#define boot_page_erase(address) __boot_page_erase_alternate(address)
|
||||
#define boot_page_write(address) __boot_page_write_alternate(address)
|
||||
#define boot_rww_enable() __boot_rww_enable_alternate()
|
||||
#define boot_lock_bits_set(lock_bits) __boot_lock_bits_set_alternate(lock_bits)
|
||||
|
||||
#elif (FLASHEND > USHRT_MAX)
|
||||
|
||||
/* Extended: >16 bit address */
|
||||
#define boot_page_fill(address, data) __boot_page_fill_extended_short(address, data)
|
||||
#define boot_page_erase(address) __boot_page_erase_extended_short(address)
|
||||
#define boot_page_write(address) __boot_page_write_extended_short(address)
|
||||
#define boot_rww_enable() __boot_rww_enable_short()
|
||||
#define boot_lock_bits_set(lock_bits) __boot_lock_bits_set_short(lock_bits)
|
||||
|
||||
#else
|
||||
|
||||
/* Normal: 16 bit address */
|
||||
#define boot_page_fill(address, data) __boot_page_fill_short(address, data)
|
||||
#define boot_page_erase(address) __boot_page_erase_short(address)
|
||||
#define boot_page_write(address) __boot_page_write_short(address)
|
||||
#define boot_rww_enable() __boot_rww_enable_short()
|
||||
#define boot_lock_bits_set(lock_bits) __boot_lock_bits_set_short(lock_bits)
|
||||
|
||||
#endif
|
||||
|
||||
/** \ingroup avr_boot
|
||||
|
||||
Same as boot_page_fill() except it waits for eeprom and spm operations to
|
||||
complete before filling the page. */
|
||||
|
||||
#define boot_page_fill_safe(address, data) \
|
||||
do { \
|
||||
boot_spm_busy_wait(); \
|
||||
eeprom_busy_wait(); \
|
||||
boot_page_fill(address, data); \
|
||||
} while (0)
|
||||
|
||||
/** \ingroup avr_boot
|
||||
|
||||
Same as boot_page_erase() except it waits for eeprom and spm operations to
|
||||
complete before erasing the page. */
|
||||
|
||||
#define boot_page_erase_safe(address) \
|
||||
do { \
|
||||
boot_spm_busy_wait(); \
|
||||
eeprom_busy_wait(); \
|
||||
boot_page_erase (address); \
|
||||
} while (0)
|
||||
|
||||
/** \ingroup avr_boot
|
||||
|
||||
Same as boot_page_write() except it waits for eeprom and spm operations to
|
||||
complete before writing the page. */
|
||||
|
||||
#define boot_page_write_safe(address) \
|
||||
do { \
|
||||
boot_spm_busy_wait(); \
|
||||
eeprom_busy_wait(); \
|
||||
boot_page_write (address); \
|
||||
} while (0)
|
||||
|
||||
/** \ingroup avr_boot
|
||||
|
||||
Same as boot_rww_enable() except waits for eeprom and spm operations to
|
||||
complete before enabling the RWW mameory. */
|
||||
|
||||
#define boot_rww_enable_safe() \
|
||||
do { \
|
||||
boot_spm_busy_wait(); \
|
||||
eeprom_busy_wait(); \
|
||||
boot_rww_enable(); \
|
||||
} while (0)
|
||||
|
||||
/** \ingroup avr_boot
|
||||
|
||||
Same as boot_lock_bits_set() except waits for eeprom and spm operations to
|
||||
complete before setting the lock bits. */
|
||||
|
||||
#define boot_lock_bits_set_safe(lock_bits) \
|
||||
do { \
|
||||
boot_spm_busy_wait(); \
|
||||
eeprom_busy_wait(); \
|
||||
boot_lock_bits_set (lock_bits); \
|
||||
} while (0)
|
||||
|
||||
#endif /* _AVR_BOOT_H_ */
|
||||
|
|
@ -0,0 +1,724 @@
|
|||
/**********************************************************/
|
||||
/* -Wl,-section-start=bootloader=0x1fc00 */
|
||||
/* Optiboot bootloader for Arduino */
|
||||
/* */
|
||||
/* http://optiboot.googlecode.com */
|
||||
/* */
|
||||
/* Arduino-maintained version : See README.TXT */
|
||||
/* http://code.google.com/p/arduino/ */
|
||||
/* */
|
||||
/* Heavily optimised bootloader that is faster and */
|
||||
/* smaller than the Arduino standard bootloader */
|
||||
/* */
|
||||
/* Enhancements: */
|
||||
/* Fits in 512 bytes, saving 1.5K of code space */
|
||||
/* Background page erasing speeds up programming */
|
||||
/* Higher baud rate speeds up programming */
|
||||
/* Written almost entirely in C */
|
||||
/* Customisable timeout with accurate timeconstant */
|
||||
/* Optional virtual UART. No hardware UART required. */
|
||||
/* Optional virtual boot partition for devices without. */
|
||||
/* */
|
||||
/* What you lose: */
|
||||
/* Implements a skeleton STK500 protocol which is */
|
||||
/* missing several features including EEPROM */
|
||||
/* programming and non-page-aligned writes */
|
||||
/* High baud rate breaks compatibility with standard */
|
||||
/* Arduino flash settings */
|
||||
/* */
|
||||
/* Fully supported: */
|
||||
/* ATmega168 based devices (Diecimila etc) */
|
||||
/* ATmega328P based devices (Duemilanove etc) */
|
||||
/* */
|
||||
/* Alpha test */
|
||||
/* ATmega1280 based devices (Arduino Mega) */
|
||||
/* */
|
||||
/* Work in progress: */
|
||||
/* ATmega644P based devices (Sanguino) */
|
||||
/* ATtiny84 based devices (Luminet) */
|
||||
/* */
|
||||
/* Does not support: */
|
||||
/* USB based devices (eg. Teensy) */
|
||||
/* */
|
||||
/* Assumptions: */
|
||||
/* The code makes several assumptions that reduce the */
|
||||
/* code size. They are all true after a hardware reset, */
|
||||
/* but may not be true if the bootloader is called by */
|
||||
/* other means or on other hardware. */
|
||||
/* No interrupts can occur */
|
||||
/* UART and Timer 1 are set to their reset state */
|
||||
/* SP points to RAMEND */
|
||||
/* */
|
||||
/* Code builds on code, libraries and optimisations from: */
|
||||
/* stk500boot.c by Jason P. Kyle */
|
||||
/* Arduino bootloader http://arduino.cc */
|
||||
/* Spiff's 1K bootloader http://spiffie.org/know/arduino_1k_bootloader/bootloader.shtml */
|
||||
/* avr-libc project http://nongnu.org/avr-libc */
|
||||
/* Adaboot http://www.ladyada.net/library/arduino/bootloader.html */
|
||||
/* AVR305 Atmel Application Note */
|
||||
/* */
|
||||
/* This program is free software; you can redistribute it */
|
||||
/* and/or modify it under the terms of the GNU General */
|
||||
/* Public License as published by the Free Software */
|
||||
/* Foundation; either version 2 of the License, or */
|
||||
/* (at your option) any later version. */
|
||||
/* */
|
||||
/* This program is distributed in the hope that it will */
|
||||
/* be useful, but WITHOUT ANY WARRANTY; without even the */
|
||||
/* implied warranty of MERCHANTABILITY or FITNESS FOR A */
|
||||
/* PARTICULAR PURPOSE. See the GNU General Public */
|
||||
/* License for more details. */
|
||||
/* */
|
||||
/* You should have received a copy of the GNU General */
|
||||
/* Public License along with this program; if not, write */
|
||||
/* to the Free Software Foundation, Inc., */
|
||||
/* 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */
|
||||
/* */
|
||||
/* Licence can be viewed at */
|
||||
/* http://www.fsf.org/licenses/gpl.txt */
|
||||
/* */
|
||||
/**********************************************************/
|
||||
|
||||
|
||||
/**********************************************************/
|
||||
/* */
|
||||
/* Optional defines: */
|
||||
/* */
|
||||
/**********************************************************/
|
||||
/* */
|
||||
/* BIG_BOOT: */
|
||||
/* Build a 1k bootloader, not 512 bytes. This turns on */
|
||||
/* extra functionality. */
|
||||
/* */
|
||||
/* BAUD_RATE: */
|
||||
/* Set bootloader baud rate. */
|
||||
/* */
|
||||
/* LUDICROUS_SPEED: */
|
||||
/* 230400 baud :-) */
|
||||
/* */
|
||||
/* SOFT_UART: */
|
||||
/* Use AVR305 soft-UART instead of hardware UART. */
|
||||
/* */
|
||||
/* LED_START_FLASHES: */
|
||||
/* Number of LED flashes on bootup. */
|
||||
/* */
|
||||
/* LED_DATA_FLASH: */
|
||||
/* Flash LED when transferring data. For boards without */
|
||||
/* TX or RX LEDs, or for people who like blinky lights. */
|
||||
/* */
|
||||
/* SUPPORT_EEPROM: */
|
||||
/* Support reading and writing from EEPROM. This is not */
|
||||
/* used by Arduino, so off by default. */
|
||||
/* */
|
||||
/* TIMEOUT_MS: */
|
||||
/* Bootloader timeout period, in milliseconds. */
|
||||
/* 500,1000,2000,4000,8000 supported. */
|
||||
/* */
|
||||
/**********************************************************/
|
||||
|
||||
/**********************************************************/
|
||||
/* Version Numbers! */
|
||||
/* */
|
||||
/* Arduino Optiboot now includes this Version number in */
|
||||
/* the source and object code. */
|
||||
/* */
|
||||
/* Version 3 was released as zip from the optiboot */
|
||||
/* repository and was distributed with Arduino 0022. */
|
||||
/* Version 4 starts with the arduino repository commit */
|
||||
/* that brought the arduino repository up-to-date with */
|
||||
/* the optiboot source tree changes since v3. */
|
||||
/* */
|
||||
/**********************************************************/
|
||||
|
||||
/**********************************************************/
|
||||
/* Edit History: */
|
||||
/* */
|
||||
/* Jan 2012: */
|
||||
/* 4.5 WestfW: fix NRWW value for m1284. */
|
||||
/* 4.4 WestfW: use attribute OS_main instead of naked for */
|
||||
/* main(). This allows optimizations that we */
|
||||
/* count on, which are prohibited in naked */
|
||||
/* functions due to PR42240. (keeps us less */
|
||||
/* than 512 bytes when compiler is gcc4.5 */
|
||||
/* (code from 4.3.2 remains the same.) */
|
||||
/* 4.4 WestfW and Maniacbug: Add m1284 support. This */
|
||||
/* does not change the 328 binary, so the */
|
||||
/* version number didn't change either. (?) */
|
||||
/* June 2011: */
|
||||
/* 4.4 WestfW: remove automatic soft_uart detect (didn't */
|
||||
/* know what it was doing or why.) Added a */
|
||||
/* check of the calculated BRG value instead. */
|
||||
/* Version stays 4.4; existing binaries are */
|
||||
/* not changed. */
|
||||
/* 4.4 WestfW: add initialization of address to keep */
|
||||
/* the compiler happy. Change SC'ed targets. */
|
||||
/* Return the SW version via READ PARAM */
|
||||
/* 4.3 WestfW: catch framing errors in getch(), so that */
|
||||
/* AVRISP works without HW kludges. */
|
||||
/* http://code.google.com/p/arduino/issues/detail?id=368n*/
|
||||
/* 4.2 WestfW: reduce code size, fix timeouts, change */
|
||||
/* verifySpace to use WDT instead of appstart */
|
||||
/* 4.1 WestfW: put version number in binary. */
|
||||
/**********************************************************/
|
||||
|
||||
#define OPTIBOOT_MAJVER 4
|
||||
#define OPTIBOOT_MINVER 5
|
||||
|
||||
#define MAKESTR(a) #a
|
||||
#define MAKEVER(a, b) MAKESTR(a*256+b)
|
||||
|
||||
asm(" .section .version\n"
|
||||
"optiboot_version: .word " MAKEVER(OPTIBOOT_MAJVER, OPTIBOOT_MINVER) "\n"
|
||||
" .section .text\n");
|
||||
|
||||
#include <inttypes.h>
|
||||
#include <avr/io.h>
|
||||
#include <avr/pgmspace.h>
|
||||
|
||||
// <avr/boot.h> uses sts instructions, but this version uses out instructions
|
||||
// This saves cycles and program memory.
|
||||
#include "boot.h"
|
||||
|
||||
|
||||
// We don't use <avr/wdt.h> as those routines have interrupt overhead we don't need.
|
||||
|
||||
#include "pin_defs.h"
|
||||
#include "stk500.h"
|
||||
|
||||
#ifndef LED_START_FLASHES
|
||||
#define LED_START_FLASHES 0
|
||||
#endif
|
||||
|
||||
#ifdef LUDICROUS_SPEED
|
||||
#define BAUD_RATE 230400L
|
||||
#endif
|
||||
|
||||
/* set the UART baud rate defaults */
|
||||
#ifndef BAUD_RATE
|
||||
#if F_CPU >= 8000000L
|
||||
#define BAUD_RATE 115200L // Highest rate Avrdude win32 will support
|
||||
#elsif F_CPU >= 1000000L
|
||||
#define BAUD_RATE 9600L // 19200 also supported, but with significant error
|
||||
#elsif F_CPU >= 128000L
|
||||
#define BAUD_RATE 4800L // Good for 128kHz internal RC
|
||||
#else
|
||||
#define BAUD_RATE 1200L // Good even at 32768Hz
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#if 0
|
||||
/* Switch in soft UART for hard baud rates */
|
||||
/*
|
||||
* I don't understand what this was supposed to accomplish, where the
|
||||
* constant "280" came from, or why automatically (and perhaps unexpectedly)
|
||||
* switching to a soft uart is a good thing, so I'm undoing this in favor
|
||||
* of a range check using the same calc used to config the BRG...
|
||||
*/
|
||||
#if (F_CPU/BAUD_RATE) > 280 // > 57600 for 16MHz
|
||||
#ifndef SOFT_UART
|
||||
#define SOFT_UART
|
||||
#endif
|
||||
#endif
|
||||
#else // 0
|
||||
#if (F_CPU + BAUD_RATE * 4L) / (BAUD_RATE * 8L) - 1 > 250
|
||||
#error Unachievable baud rate (too slow) BAUD_RATE
|
||||
#endif // baud rate slow check
|
||||
#if (F_CPU + BAUD_RATE * 4L) / (BAUD_RATE * 8L) - 1 < 3
|
||||
#error Unachievable baud rate (too fast) BAUD_RATE
|
||||
#endif // baud rate fastn check
|
||||
#endif
|
||||
|
||||
/* Watchdog settings */
|
||||
#define WATCHDOG_OFF (0)
|
||||
#define WATCHDOG_16MS (_BV(WDE))
|
||||
#define WATCHDOG_32MS (_BV(WDP0) | _BV(WDE))
|
||||
#define WATCHDOG_64MS (_BV(WDP1) | _BV(WDE))
|
||||
#define WATCHDOG_125MS (_BV(WDP1) | _BV(WDP0) | _BV(WDE))
|
||||
#define WATCHDOG_250MS (_BV(WDP2) | _BV(WDE))
|
||||
#define WATCHDOG_500MS (_BV(WDP2) | _BV(WDP0) | _BV(WDE))
|
||||
#define WATCHDOG_1S (_BV(WDP2) | _BV(WDP1) | _BV(WDE))
|
||||
#define WATCHDOG_2S (_BV(WDP2) | _BV(WDP1) | _BV(WDP0) | _BV(WDE))
|
||||
#ifndef __AVR_ATmega8__
|
||||
#define WATCHDOG_4S (_BV(WDP3) | _BV(WDE))
|
||||
#define WATCHDOG_8S (_BV(WDP3) | _BV(WDP0) | _BV(WDE))
|
||||
#endif
|
||||
|
||||
/* Function Prototypes */
|
||||
/* The main function is in init9, which removes the interrupt vector table */
|
||||
/* we don't need. It is also 'naked', which means the compiler does not */
|
||||
/* generate any entry or exit code itself. */
|
||||
int main(void) __attribute__ ((OS_main)) __attribute__ ((section (".init9")));
|
||||
void putch(char);
|
||||
uint8_t getch(void);
|
||||
static inline void getNch(uint8_t); /* "static inline" is a compiler hint to reduce code size */
|
||||
void verifySpace();
|
||||
static inline void flash_led(uint8_t);
|
||||
uint8_t getLen();
|
||||
static inline void watchdogReset();
|
||||
void watchdogConfig(uint8_t x);
|
||||
#ifdef SOFT_UART
|
||||
void uartDelay() __attribute__ ((naked));
|
||||
#endif
|
||||
void appStart() __attribute__ ((naked));
|
||||
|
||||
/*
|
||||
* NRWW memory
|
||||
* Addresses below NRWW (Non-Read-While-Write) can be programmed while
|
||||
* continuing to run code from flash, slightly speeding up programming
|
||||
* time. Beware that Atmel data sheets specify this as a WORD address,
|
||||
* while optiboot will be comparing against a 16-bit byte address. This
|
||||
* means that on a part with 128kB of memory, the upper part of the lower
|
||||
* 64k will get NRWW processing as well, even though it doesn't need it.
|
||||
* That's OK. In fact, you can disable the overlapping processing for
|
||||
* a part entirely by setting NRWWSTART to zero. This reduces code
|
||||
* space a bit, at the expense of being slightly slower, overall.
|
||||
*
|
||||
* RAMSTART should be self-explanatory. It's bigger on parts with a
|
||||
* lot of peripheral registers.
|
||||
*/
|
||||
#if defined(__AVR_ATmega168__)
|
||||
#define RAMSTART (0x100)
|
||||
#define NRWWSTART (0x3800)
|
||||
#elif defined(__AVR_ATmega328P__)
|
||||
#define RAMSTART (0x100)
|
||||
#define NRWWSTART (0x7000)
|
||||
#elif defined (__AVR_ATmega644P__)
|
||||
#define RAMSTART (0x100)
|
||||
#define NRWWSTART (0xE000)
|
||||
#elif defined (__AVR_ATmega1284P__)
|
||||
#define RAMSTART (0x100)
|
||||
#define NRWWSTART (0xE000)
|
||||
#elif defined(__AVR_ATtiny84__)
|
||||
#define RAMSTART (0x100)
|
||||
#define NRWWSTART (0x0000)
|
||||
#elif defined(__AVR_ATmega1280__)
|
||||
#define RAMSTART (0x200)
|
||||
#define NRWWSTART (0xE000)
|
||||
#elif defined(__AVR_ATmega8__) || defined(__AVR_ATmega88__)
|
||||
#define RAMSTART (0x100)
|
||||
#define NRWWSTART (0x1800)
|
||||
#endif
|
||||
|
||||
/* C zero initialises all global variables. However, that requires */
|
||||
/* These definitions are NOT zero initialised, but that doesn't matter */
|
||||
/* This allows us to drop the zero init code, saving us memory */
|
||||
#define buff ((uint8_t*)(RAMSTART))
|
||||
#ifdef VIRTUAL_BOOT_PARTITION
|
||||
#define rstVect (*(uint16_t*)(RAMSTART+SPM_PAGESIZE*2+4))
|
||||
#define wdtVect (*(uint16_t*)(RAMSTART+SPM_PAGESIZE*2+6))
|
||||
#endif
|
||||
|
||||
/* main program starts here */
|
||||
int main(void) {
|
||||
uint8_t ch;
|
||||
|
||||
/*
|
||||
* Making these local and in registers prevents the need for initializing
|
||||
* them, and also saves space because code no longer stores to memory.
|
||||
* (initializing address keeps the compiler happy, but isn't really
|
||||
* necessary, and uses 4 bytes of flash.)
|
||||
*/
|
||||
register uint16_t address = 0;
|
||||
register uint8_t length;
|
||||
|
||||
// After the zero init loop, this is the first code to run.
|
||||
//
|
||||
// This code makes the following assumptions:
|
||||
// No interrupts will execute
|
||||
// SP points to RAMEND
|
||||
// r1 contains zero
|
||||
//
|
||||
// If not, uncomment the following instructions:
|
||||
// cli();
|
||||
asm volatile ("clr __zero_reg__");
|
||||
#ifdef __AVR_ATmega8__
|
||||
SP=RAMEND; // This is done by hardware reset
|
||||
#endif
|
||||
|
||||
// Adaboot no-wait mod
|
||||
ch = MCUSR;
|
||||
MCUSR = 0;
|
||||
if (!(ch & _BV(EXTRF))) appStart();
|
||||
|
||||
#if LED_START_FLASHES > 0
|
||||
// Set up Timer 1 for timeout counter
|
||||
TCCR1B = _BV(CS12) | _BV(CS10); // div 1024
|
||||
#endif
|
||||
#ifndef SOFT_UART
|
||||
#ifdef __AVR_ATmega8__
|
||||
UCSRA = _BV(U2X); //Double speed mode USART
|
||||
UCSRB = _BV(RXEN) | _BV(TXEN); // enable Rx & Tx
|
||||
UCSRC = _BV(URSEL) | _BV(UCSZ1) | _BV(UCSZ0); // config USART; 8N1
|
||||
UBRRL = (uint8_t)( (F_CPU + BAUD_RATE * 4L) / (BAUD_RATE * 8L) - 1 );
|
||||
#else
|
||||
UCSR0A = _BV(U2X0); //Double speed mode USART0
|
||||
UCSR0B = _BV(RXEN0) | _BV(TXEN0);
|
||||
UCSR0C = _BV(UCSZ00) | _BV(UCSZ01);
|
||||
UBRR0L = (uint8_t)( (F_CPU + BAUD_RATE * 4L) / (BAUD_RATE * 8L) - 1 );
|
||||
#endif
|
||||
#endif
|
||||
|
||||
// Set up watchdog to trigger after 500ms
|
||||
watchdogConfig(WATCHDOG_1S);
|
||||
|
||||
/* Set LED pin as output */
|
||||
LED_DDR |= _BV(LED);
|
||||
|
||||
#ifdef SOFT_UART
|
||||
/* Set TX pin as output */
|
||||
UART_DDR |= _BV(UART_TX_BIT);
|
||||
#endif
|
||||
|
||||
#if LED_START_FLASHES > 0
|
||||
/* Flash onboard LED to signal entering of bootloader */
|
||||
flash_led(LED_START_FLASHES * 2);
|
||||
#endif
|
||||
|
||||
/* Forever loop */
|
||||
for (;;) {
|
||||
/* get character from UART */
|
||||
ch = getch();
|
||||
|
||||
if(ch == STK_GET_PARAMETER) {
|
||||
unsigned char which = getch();
|
||||
verifySpace();
|
||||
if (which == 0x82) {
|
||||
/*
|
||||
* Send optiboot version as "minor SW version"
|
||||
*/
|
||||
putch(OPTIBOOT_MINVER);
|
||||
} else if (which == 0x81) {
|
||||
putch(OPTIBOOT_MAJVER);
|
||||
} else {
|
||||
/*
|
||||
* GET PARAMETER returns a generic 0x03 reply for
|
||||
* other parameters - enough to keep Avrdude happy
|
||||
*/
|
||||
putch(0x03);
|
||||
}
|
||||
}
|
||||
else if(ch == STK_SET_DEVICE) {
|
||||
// SET DEVICE is ignored
|
||||
getNch(20);
|
||||
}
|
||||
else if(ch == STK_SET_DEVICE_EXT) {
|
||||
// SET DEVICE EXT is ignored
|
||||
getNch(5);
|
||||
}
|
||||
else if(ch == STK_LOAD_ADDRESS) {
|
||||
// LOAD ADDRESS
|
||||
uint16_t newAddress;
|
||||
newAddress = getch();
|
||||
newAddress = (newAddress & 0xff) | (getch() << 8);
|
||||
#ifdef RAMPZ
|
||||
// Transfer top bit to RAMPZ
|
||||
RAMPZ = (newAddress & 0x8000) ? 1 : 0;
|
||||
#endif
|
||||
newAddress += newAddress; // Convert from word address to byte address
|
||||
address = newAddress;
|
||||
verifySpace();
|
||||
}
|
||||
else if(ch == STK_UNIVERSAL) {
|
||||
// UNIVERSAL command is ignored
|
||||
getNch(4);
|
||||
putch(0x00);
|
||||
}
|
||||
/* Write memory, length is big endian and is in bytes */
|
||||
else if(ch == STK_PROG_PAGE) {
|
||||
// PROGRAM PAGE - we support flash programming only, not EEPROM
|
||||
uint8_t *bufPtr;
|
||||
uint16_t addrPtr;
|
||||
|
||||
getch(); /* getlen() */
|
||||
length = getch();
|
||||
getch();
|
||||
|
||||
// If we are in RWW section, immediately start page erase
|
||||
if (address < NRWWSTART) __boot_page_erase_short((uint16_t)(void*)address);
|
||||
|
||||
// While that is going on, read in page contents
|
||||
bufPtr = buff;
|
||||
do *bufPtr++ = getch();
|
||||
while (--length);
|
||||
|
||||
// If we are in NRWW section, page erase has to be delayed until now.
|
||||
// Todo: Take RAMPZ into account
|
||||
if (address >= NRWWSTART) __boot_page_erase_short((uint16_t)(void*)address);
|
||||
|
||||
// Read command terminator, start reply
|
||||
verifySpace();
|
||||
|
||||
// If only a partial page is to be programmed, the erase might not be complete.
|
||||
// So check that here
|
||||
boot_spm_busy_wait();
|
||||
|
||||
#ifdef VIRTUAL_BOOT_PARTITION
|
||||
if ((uint16_t)(void*)address == 0) {
|
||||
// This is the reset vector page. We need to live-patch the code so the
|
||||
// bootloader runs.
|
||||
//
|
||||
// Move RESET vector to WDT vector
|
||||
uint16_t vect = buff[0] | (buff[1]<<8);
|
||||
rstVect = vect;
|
||||
wdtVect = buff[8] | (buff[9]<<8);
|
||||
vect -= 4; // Instruction is a relative jump (rjmp), so recalculate.
|
||||
buff[8] = vect & 0xff;
|
||||
buff[9] = vect >> 8;
|
||||
|
||||
// Add jump to bootloader at RESET vector
|
||||
buff[0] = 0x7f;
|
||||
buff[1] = 0xce; // rjmp 0x1d00 instruction
|
||||
}
|
||||
#endif
|
||||
|
||||
// Copy buffer into programming buffer
|
||||
bufPtr = buff;
|
||||
addrPtr = (uint16_t)(void*)address;
|
||||
ch = SPM_PAGESIZE / 2;
|
||||
do {
|
||||
uint16_t a;
|
||||
a = *bufPtr++;
|
||||
a |= (*bufPtr++) << 8;
|
||||
__boot_page_fill_short((uint16_t)(void*)addrPtr,a);
|
||||
addrPtr += 2;
|
||||
} while (--ch);
|
||||
|
||||
// Write from programming buffer
|
||||
__boot_page_write_short((uint16_t)(void*)address);
|
||||
boot_spm_busy_wait();
|
||||
|
||||
#if defined(RWWSRE)
|
||||
// Reenable read access to flash
|
||||
boot_rww_enable();
|
||||
#endif
|
||||
|
||||
}
|
||||
/* Read memory block mode, length is big endian. */
|
||||
else if(ch == STK_READ_PAGE) {
|
||||
// READ PAGE - we only read flash
|
||||
getch(); /* getlen() */
|
||||
length = getch();
|
||||
getch();
|
||||
|
||||
verifySpace();
|
||||
#ifdef VIRTUAL_BOOT_PARTITION
|
||||
do {
|
||||
// Undo vector patch in bottom page so verify passes
|
||||
if (address == 0) ch=rstVect & 0xff;
|
||||
else if (address == 1) ch=rstVect >> 8;
|
||||
else if (address == 8) ch=wdtVect & 0xff;
|
||||
else if (address == 9) ch=wdtVect >> 8;
|
||||
else ch = pgm_read_byte_near(address);
|
||||
address++;
|
||||
putch(ch);
|
||||
} while (--length);
|
||||
#else
|
||||
#ifdef RAMPZ
|
||||
// Since RAMPZ should already be set, we need to use EPLM directly.
|
||||
// do putch(pgm_read_byte_near(address++));
|
||||
// while (--length);
|
||||
do {
|
||||
uint8_t result;
|
||||
__asm__ ("elpm %0,Z\n":"=r"(result):"z"(address));
|
||||
putch(result);
|
||||
address++;
|
||||
}
|
||||
while (--length);
|
||||
#else
|
||||
do putch(pgm_read_byte_near(address++));
|
||||
while (--length);
|
||||
#endif
|
||||
#endif
|
||||
}
|
||||
|
||||
/* Get device signature bytes */
|
||||
else if(ch == STK_READ_SIGN) {
|
||||
// READ SIGN - return what Avrdude wants to hear
|
||||
verifySpace();
|
||||
putch(SIGNATURE_0);
|
||||
putch(SIGNATURE_1);
|
||||
putch(SIGNATURE_2);
|
||||
}
|
||||
else if (ch == STK_LEAVE_PROGMODE) { /* 'Q' */
|
||||
// Adaboot no-wait mod
|
||||
watchdogConfig(WATCHDOG_16MS);
|
||||
verifySpace();
|
||||
}
|
||||
else {
|
||||
// This covers the response to commands like STK_ENTER_PROGMODE
|
||||
verifySpace();
|
||||
}
|
||||
putch(STK_OK);
|
||||
}
|
||||
}
|
||||
|
||||
void putch(char ch) {
|
||||
#ifndef SOFT_UART
|
||||
while (!(UCSR0A & _BV(UDRE0)));
|
||||
UDR0 = ch;
|
||||
#else
|
||||
__asm__ __volatile__ (
|
||||
" com %[ch]\n" // ones complement, carry set
|
||||
" sec\n"
|
||||
"1: brcc 2f\n"
|
||||
" cbi %[uartPort],%[uartBit]\n"
|
||||
" rjmp 3f\n"
|
||||
"2: sbi %[uartPort],%[uartBit]\n"
|
||||
" nop\n"
|
||||
"3: rcall uartDelay\n"
|
||||
" rcall uartDelay\n"
|
||||
" lsr %[ch]\n"
|
||||
" dec %[bitcnt]\n"
|
||||
" brne 1b\n"
|
||||
:
|
||||
:
|
||||
[bitcnt] "d" (10),
|
||||
[ch] "r" (ch),
|
||||
[uartPort] "I" (_SFR_IO_ADDR(UART_PORT)),
|
||||
[uartBit] "I" (UART_TX_BIT)
|
||||
:
|
||||
"r25"
|
||||
);
|
||||
#endif
|
||||
}
|
||||
|
||||
uint8_t getch(void) {
|
||||
uint8_t ch;
|
||||
|
||||
#ifdef LED_DATA_FLASH
|
||||
#ifdef __AVR_ATmega8__
|
||||
LED_PORT ^= _BV(LED);
|
||||
#else
|
||||
LED_PIN |= _BV(LED);
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#ifdef SOFT_UART
|
||||
__asm__ __volatile__ (
|
||||
"1: sbic %[uartPin],%[uartBit]\n" // Wait for start edge
|
||||
" rjmp 1b\n"
|
||||
" rcall uartDelay\n" // Get to middle of start bit
|
||||
"2: rcall uartDelay\n" // Wait 1 bit period
|
||||
" rcall uartDelay\n" // Wait 1 bit period
|
||||
" clc\n"
|
||||
" sbic %[uartPin],%[uartBit]\n"
|
||||
" sec\n"
|
||||
" dec %[bitCnt]\n"
|
||||
" breq 3f\n"
|
||||
" ror %[ch]\n"
|
||||
" rjmp 2b\n"
|
||||
"3:\n"
|
||||
:
|
||||
[ch] "=r" (ch)
|
||||
:
|
||||
[bitCnt] "d" (9),
|
||||
[uartPin] "I" (_SFR_IO_ADDR(UART_PIN)),
|
||||
[uartBit] "I" (UART_RX_BIT)
|
||||
:
|
||||
"r25"
|
||||
);
|
||||
#else
|
||||
while(!(UCSR0A & _BV(RXC0)))
|
||||
;
|
||||
if (!(UCSR0A & _BV(FE0))) {
|
||||
/*
|
||||
* A Framing Error indicates (probably) that something is talking
|
||||
* to us at the wrong bit rate. Assume that this is because it
|
||||
* expects to be talking to the application, and DON'T reset the
|
||||
* watchdog. This should cause the bootloader to abort and run
|
||||
* the application "soon", if it keeps happening. (Note that we
|
||||
* don't care that an invalid char is returned...)
|
||||
*/
|
||||
watchdogReset();
|
||||
}
|
||||
|
||||
ch = UDR0;
|
||||
#endif
|
||||
|
||||
#ifdef LED_DATA_FLASH
|
||||
#ifdef __AVR_ATmega8__
|
||||
LED_PORT ^= _BV(LED);
|
||||
#else
|
||||
LED_PIN |= _BV(LED);
|
||||
#endif
|
||||
#endif
|
||||
|
||||
return ch;
|
||||
}
|
||||
|
||||
#ifdef SOFT_UART
|
||||
// AVR305 equation: #define UART_B_VALUE (((F_CPU/BAUD_RATE)-23)/6)
|
||||
// Adding 3 to numerator simulates nearest rounding for more accurate baud rates
|
||||
#define UART_B_VALUE (((F_CPU/BAUD_RATE)-20)/6)
|
||||
#if UART_B_VALUE > 255
|
||||
#error Baud rate too slow for soft UART
|
||||
#endif
|
||||
|
||||
void uartDelay() {
|
||||
__asm__ __volatile__ (
|
||||
"ldi r25,%[count]\n"
|
||||
"1:dec r25\n"
|
||||
"brne 1b\n"
|
||||
"ret\n"
|
||||
::[count] "M" (UART_B_VALUE)
|
||||
);
|
||||
}
|
||||
#endif
|
||||
|
||||
void getNch(uint8_t count) {
|
||||
do getch(); while (--count);
|
||||
verifySpace();
|
||||
}
|
||||
|
||||
void verifySpace() {
|
||||
if (getch() != CRC_EOP) {
|
||||
watchdogConfig(WATCHDOG_16MS); // shorten WD timeout
|
||||
while (1) // and busy-loop so that WD causes
|
||||
; // a reset and app start.
|
||||
}
|
||||
putch(STK_INSYNC);
|
||||
}
|
||||
|
||||
#if LED_START_FLASHES > 0
|
||||
void flash_led(uint8_t count) {
|
||||
do {
|
||||
TCNT1 = -(F_CPU/(1024*16));
|
||||
TIFR1 = _BV(TOV1);
|
||||
while(!(TIFR1 & _BV(TOV1)));
|
||||
#ifdef __AVR_ATmega8__
|
||||
LED_PORT ^= _BV(LED);
|
||||
#else
|
||||
LED_PIN |= _BV(LED);
|
||||
#endif
|
||||
watchdogReset();
|
||||
} while (--count);
|
||||
}
|
||||
#endif
|
||||
|
||||
// Watchdog functions. These are only safe with interrupts turned off.
|
||||
void watchdogReset() {
|
||||
__asm__ __volatile__ (
|
||||
"wdr\n"
|
||||
);
|
||||
}
|
||||
|
||||
void watchdogConfig(uint8_t x) {
|
||||
WDTCSR = _BV(WDCE) | _BV(WDE);
|
||||
WDTCSR = x;
|
||||
}
|
||||
|
||||
void appStart() {
|
||||
watchdogConfig(WATCHDOG_OFF);
|
||||
__asm__ __volatile__ (
|
||||
#ifdef VIRTUAL_BOOT_PARTITION
|
||||
// Jump to WDT vector
|
||||
"ldi r30,4\n"
|
||||
"clr r31\n"
|
||||
#else
|
||||
// Jump to RST vector
|
||||
"clr r30\n"
|
||||
"clr r31\n"
|
||||
#endif
|
||||
"ijmp\n"
|
||||
);
|
||||
}
|
||||
|
|
@ -0,0 +1,33 @@
|
|||
:020000021000EC
|
||||
:10FE00000F92CDB7DEB7112484B714BE81FFDFD0C7
|
||||
:10FE100082E08093C00088E18093C10086E08093F7
|
||||
:10FE2000C2008AE28093C4008EE0BBD0209A00E03A
|
||||
:10FE300010E0EE24E394E1E1DE2EF3E0FF2EA5D006
|
||||
:10FE4000813471F4A2D08983B2D08981823809F4D7
|
||||
:10FE50008BC0813811F484E001C083E08FD08BC067
|
||||
:10FE6000823411F484E103C0853419F485E0A7D00D
|
||||
:10FE700082C0853591F489D0A82EBB2486D0082F66
|
||||
:10FE800010E0102F00270A291B29812F881F88279F
|
||||
:10FE9000881F8BBF000F111F6DC0863521F484E0D1
|
||||
:10FEA0008ED080E0DBCF843609F040C06ED06DD0BC
|
||||
:10FEB000C82E6BD080EE0030180718F4F801F7BE9A
|
||||
:10FEC000E895A12C51E0B52E60D0F50181935F013A
|
||||
:10FED000CE16D1F7F0EE00301F0718F0F801F7BE8C
|
||||
:10FEE000E89565D007B600FCFDCFF801A0E0B1E0D1
|
||||
:10FEF0002C9130E011968C91119790E0982F8827E3
|
||||
:10FF0000822B932B12960C01E7BEE89511243296B2
|
||||
:10FF100082E0A030B80761F785E0F80187BFE89577
|
||||
:10FF200007B600FCFDCFD7BEE89525C08437A9F4FD
|
||||
:10FF30002CD02BD0B82E29D03AD0CB2C4801F401AC
|
||||
:10FF400086911CD00894811C911CCA94C1F70F5F44
|
||||
:10FF50001F4FBA940B0D111D0EC0853739F427D0F1
|
||||
:10FF60008EE10CD087E90AD085E078CF813511F495
|
||||
:10FF700088E017D01CD080E101D061CF9091C00003
|
||||
:10FF800095FFFCCF8093C60008958091C00087FF45
|
||||
:10FF9000FCCF8091C00084FD01C0A8958091C6006F
|
||||
:10FFA0000895E0E6F0E098E1908380830895EDDF26
|
||||
:10FFB000803219F088E0F5DFFFCF84E1DFCFCF9307
|
||||
:10FFC000C82FE3DFC150E9F7F2DFCF91089580E059
|
||||
:08FFD000E8DFEE27FF2709948A
|
||||
:040000031000FE00EB
|
||||
:00000001FF
|
||||
|
|
@ -0,0 +1,81 @@
|
|||
#if defined(__AVR_ATmega168__) || defined(__AVR_ATmega328P__) || defined(__AVR_ATmega88) || defined(__AVR_ATmega8__) || defined(__AVR_ATmega88__)
|
||||
/* Onboard LED is connected to pin PB5 in Arduino NG, Diecimila, and Duemilanove */
|
||||
#define LED_DDR DDRB
|
||||
#define LED_PORT PORTB
|
||||
#define LED_PIN PINB
|
||||
#define LED PINB5
|
||||
|
||||
/* Ports for soft UART */
|
||||
#ifdef SOFT_UART
|
||||
#define UART_PORT PORTD
|
||||
#define UART_PIN PIND
|
||||
#define UART_DDR DDRD
|
||||
#define UART_TX_BIT 1
|
||||
#define UART_RX_BIT 0
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#if defined(__AVR_ATmega8__)
|
||||
//Name conversion R.Wiersma
|
||||
#define UCSR0A UCSRA
|
||||
#define UDR0 UDR
|
||||
#define UDRE0 UDRE
|
||||
#define RXC0 RXC
|
||||
#define FE0 FE
|
||||
#define TIFR1 TIFR
|
||||
#define WDTCSR WDTCR
|
||||
#endif
|
||||
|
||||
/* Luminet support */
|
||||
#if defined(__AVR_ATtiny84__)
|
||||
/* Red LED is connected to pin PA4 */
|
||||
#define LED_DDR DDRA
|
||||
#define LED_PORT PORTA
|
||||
#define LED_PIN PINA
|
||||
#define LED PINA4
|
||||
/* Ports for soft UART - left port only for now. TX/RX on PA2/PA3 */
|
||||
#ifdef SOFT_UART
|
||||
#define UART_PORT PORTA
|
||||
#define UART_PIN PINA
|
||||
#define UART_DDR DDRA
|
||||
#define UART_TX_BIT 2
|
||||
#define UART_RX_BIT 3
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/* Sanguino support */
|
||||
#if defined(__AVR_ATmega644P__) || defined(__AVR_ATmega1284P__)
|
||||
/* Onboard LED is connected to pin PB0 on Sanguino */
|
||||
#define LED_DDR DDRB
|
||||
#define LED_PORT PORTB
|
||||
#define LED_PIN PINB
|
||||
#define LED PINB0
|
||||
|
||||
/* Ports for soft UART */
|
||||
#ifdef SOFT_UART
|
||||
#define UART_PORT PORTD
|
||||
#define UART_PIN PIND
|
||||
#define UART_DDR DDRD
|
||||
#define UART_TX_BIT 1
|
||||
#define UART_RX_BIT 0
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/* Mega support */
|
||||
#if defined(__AVR_ATmega1280__)
|
||||
/* Onboard LED is connected to pin PB7 on Arduino Mega */
|
||||
#define LED_DDR DDRB
|
||||
#define LED_PORT PORTB
|
||||
#define LED_PIN PINB
|
||||
#define LED PINB7
|
||||
|
||||
/* Ports for soft UART */
|
||||
#ifdef SOFT_UART
|
||||
#define UART_PORT PORTE
|
||||
#define UART_PIN PINE
|
||||
#define UART_DDR DDRE
|
||||
#define UART_TX_BIT 1
|
||||
#define UART_RX_BIT 0
|
||||
#endif
|
||||
#endif
|
||||
|
||||
|
|
@ -0,0 +1,39 @@
|
|||
/* STK500 constants list, from AVRDUDE */
|
||||
#define STK_OK 0x10
|
||||
#define STK_FAILED 0x11 // Not used
|
||||
#define STK_UNKNOWN 0x12 // Not used
|
||||
#define STK_NODEVICE 0x13 // Not used
|
||||
#define STK_INSYNC 0x14 // ' '
|
||||
#define STK_NOSYNC 0x15 // Not used
|
||||
#define ADC_CHANNEL_ERROR 0x16 // Not used
|
||||
#define ADC_MEASURE_OK 0x17 // Not used
|
||||
#define PWM_CHANNEL_ERROR 0x18 // Not used
|
||||
#define PWM_ADJUST_OK 0x19 // Not used
|
||||
#define CRC_EOP 0x20 // 'SPACE'
|
||||
#define STK_GET_SYNC 0x30 // '0'
|
||||
#define STK_GET_SIGN_ON 0x31 // '1'
|
||||
#define STK_SET_PARAMETER 0x40 // '@'
|
||||
#define STK_GET_PARAMETER 0x41 // 'A'
|
||||
#define STK_SET_DEVICE 0x42 // 'B'
|
||||
#define STK_SET_DEVICE_EXT 0x45 // 'E'
|
||||
#define STK_ENTER_PROGMODE 0x50 // 'P'
|
||||
#define STK_LEAVE_PROGMODE 0x51 // 'Q'
|
||||
#define STK_CHIP_ERASE 0x52 // 'R'
|
||||
#define STK_CHECK_AUTOINC 0x53 // 'S'
|
||||
#define STK_LOAD_ADDRESS 0x55 // 'U'
|
||||
#define STK_UNIVERSAL 0x56 // 'V'
|
||||
#define STK_PROG_FLASH 0x60 // '`'
|
||||
#define STK_PROG_DATA 0x61 // 'a'
|
||||
#define STK_PROG_FUSE 0x62 // 'b'
|
||||
#define STK_PROG_LOCK 0x63 // 'c'
|
||||
#define STK_PROG_PAGE 0x64 // 'd'
|
||||
#define STK_PROG_FUSE_EXT 0x65 // 'e'
|
||||
#define STK_READ_FLASH 0x70 // 'p'
|
||||
#define STK_READ_DATA 0x71 // 'q'
|
||||
#define STK_READ_FUSE 0x72 // 'r'
|
||||
#define STK_READ_LOCK 0x73 // 's'
|
||||
#define STK_READ_PAGE 0x74 // 't'
|
||||
#define STK_READ_SIGN 0x75 // 'u'
|
||||
#define STK_READ_OSCCAL 0x76 // 'v'
|
||||
#define STK_READ_FUSE_EXT 0x77 // 'w'
|
||||
#define STK_READ_OSCCAL_EXT 0x78 // 'x'
|
||||
|
|
@ -1,135 +0,0 @@
|
|||
/*
|
||||
wiring.h - Partial implementation of the Wiring API for the ATmega8.
|
||||
Part of Arduino - http://www.arduino.cc/
|
||||
|
||||
Copyright (c) 2005-2006 David A. Mellis
|
||||
|
||||
This library is free software; you can redistribute it and/or
|
||||
modify it under the terms of the GNU Lesser General Public
|
||||
License as published by the Free Software Foundation; either
|
||||
version 2.1 of the License, or (at your option) any later version.
|
||||
|
||||
This library is distributed in the hope that it will be useful,
|
||||
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
|
||||
Lesser General Public License for more details.
|
||||
|
||||
You should have received a copy of the GNU Lesser General
|
||||
Public License along with this library; if not, write to the
|
||||
Free Software Foundation, Inc., 59 Temple Place, Suite 330,
|
||||
Boston, MA 02111-1307 USA
|
||||
|
||||
$Id$
|
||||
*/
|
||||
|
||||
#ifndef Wiring_h
|
||||
#define Wiring_h
|
||||
|
||||
#include <avr/io.h>
|
||||
#include <stdlib.h>
|
||||
#include "binary.h"
|
||||
|
||||
#ifdef __cplusplus
|
||||
extern "C"{
|
||||
#endif
|
||||
|
||||
#define HIGH 0x1
|
||||
#define LOW 0x0
|
||||
|
||||
#define INPUT 0x0
|
||||
#define OUTPUT 0x1
|
||||
|
||||
#define true 0x1
|
||||
#define false 0x0
|
||||
|
||||
#define PI 3.1415926535897932384626433832795
|
||||
#define HALF_PI 1.5707963267948966192313216916398
|
||||
#define TWO_PI 6.283185307179586476925286766559
|
||||
#define DEG_TO_RAD 0.017453292519943295769236907684886
|
||||
#define RAD_TO_DEG 57.295779513082320876798154814105
|
||||
|
||||
#define SERIAL 0x0
|
||||
#define DISPLAY 0x1
|
||||
|
||||
#define LSBFIRST 0
|
||||
#define MSBFIRST 1
|
||||
|
||||
#define CHANGE 1
|
||||
#define FALLING 2
|
||||
#define RISING 3
|
||||
|
||||
#if defined(__AVR_ATmega1280__) || defined(__AVR_ATmega2560__)
|
||||
#define INTERNAL1V1 2
|
||||
#define INTERNAL2V56 3
|
||||
#else
|
||||
#define INTERNAL 3
|
||||
#endif
|
||||
#define DEFAULT 1
|
||||
#define EXTERNAL 0
|
||||
|
||||
// undefine stdlib's abs if encountered
|
||||
#ifdef abs
|
||||
#undef abs
|
||||
#endif
|
||||
|
||||
#define min(a,b) ((a)<(b)?(a):(b))
|
||||
#define max(a,b) ((a)>(b)?(a):(b))
|
||||
#define abs(x) ((x)>0?(x):-(x))
|
||||
#define constrain(amt,low,high) ((amt)<(low)?(low):((amt)>(high)?(high):(amt)))
|
||||
#define round(x) ((x)>=0?(long)((x)+0.5):(long)((x)-0.5))
|
||||
#define radians(deg) ((deg)*DEG_TO_RAD)
|
||||
#define degrees(rad) ((rad)*RAD_TO_DEG)
|
||||
#define sq(x) ((x)*(x))
|
||||
|
||||
#define interrupts() sei()
|
||||
#define noInterrupts() cli()
|
||||
|
||||
#define clockCyclesPerMicrosecond() ( F_CPU / 1000000L )
|
||||
#define clockCyclesToMicroseconds(a) ( ((a) * 1000L) / (F_CPU / 1000L) )
|
||||
#define microsecondsToClockCycles(a) ( ((a) * (F_CPU / 1000L)) / 1000L )
|
||||
|
||||
#define lowByte(w) ((uint8_t) ((w) & 0xff))
|
||||
#define highByte(w) ((uint8_t) ((w) >> 8))
|
||||
|
||||
#define bitRead(value, bit) (((value) >> (bit)) & 0x01)
|
||||
#define bitSet(value, bit) ((value) |= (1UL << (bit)))
|
||||
#define bitClear(value, bit) ((value) &= ~(1UL << (bit)))
|
||||
#define bitWrite(value, bit, bitvalue) (bitvalue ? bitSet(value, bit) : bitClear(value, bit))
|
||||
|
||||
|
||||
typedef unsigned int word;
|
||||
|
||||
#define bit(b) (1UL << (b))
|
||||
|
||||
typedef uint8_t boolean;
|
||||
typedef uint8_t byte;
|
||||
|
||||
void init(void);
|
||||
|
||||
void pinMode(uint8_t, uint8_t);
|
||||
void digitalWrite(uint8_t, uint8_t);
|
||||
int digitalRead(uint8_t);
|
||||
int analogRead(uint8_t);
|
||||
void analogReference(uint8_t mode);
|
||||
void analogWrite(uint8_t, int);
|
||||
|
||||
unsigned long millis(void);
|
||||
unsigned long micros(void);
|
||||
void delay(unsigned long);
|
||||
void delayMicroseconds(unsigned int us);
|
||||
unsigned long pulseIn(uint8_t pin, uint8_t state, unsigned long timeout);
|
||||
|
||||
void shiftOut(uint8_t dataPin, uint8_t clockPin, uint8_t bitOrder, uint8_t val);
|
||||
uint8_t shiftIn(uint8_t dataPin, uint8_t clockPin, uint8_t bitOrder);
|
||||
|
||||
void attachInterrupt(uint8_t, void (*)(void), int mode);
|
||||
void detachInterrupt(uint8_t);
|
||||
|
||||
void setup(void);
|
||||
void loop(void);
|
||||
|
||||
#ifdef __cplusplus
|
||||
} // extern "C"
|
||||
#endif
|
||||
|
||||
#endif
|
||||
|
|
@ -37,7 +37,11 @@
|
|||
// using a ring buffer (I think), in which rx_buffer_head is the index of the
|
||||
// location to which to write the next incoming character and rx_buffer_tail
|
||||
// is the index of the location from which to read.
|
||||
#if (RAMEND < 1000)
|
||||
#define RX_BUFFER_SIZE 32
|
||||
#else
|
||||
#define RX_BUFFER_SIZE 128
|
||||
#endif
|
||||
|
||||
struct ring_buffer
|
||||
{
|
||||
|
|
@ -46,11 +50,22 @@ struct ring_buffer
|
|||
int tail;
|
||||
};
|
||||
|
||||
#if defined(UBRRH) || defined(UBRR0H)
|
||||
ring_buffer rx_buffer = { { 0 }, 0, 0 };
|
||||
#endif
|
||||
#if defined(UBRR1H)
|
||||
ring_buffer rx_buffer1 = { { 0 }, 0, 0 };
|
||||
#endif
|
||||
#if defined(UBRR2H)
|
||||
ring_buffer rx_buffer2 = { { 0 }, 0, 0 };
|
||||
#endif
|
||||
#if defined(UBRR3H)
|
||||
ring_buffer rx_buffer3 = { { 0 }, 0, 0 };
|
||||
#endif
|
||||
|
||||
inline void store_char(unsigned char c, ring_buffer *rx_buffer)
|
||||
{
|
||||
int i = (unsigned int)(rx_buffer->head + 1) & (RX_BUFFER_SIZE -1);
|
||||
int i = (unsigned int)(rx_buffer->head + 1) % RX_BUFFER_SIZE;
|
||||
|
||||
// if we should be storing the received character into the location
|
||||
// just before the tail (meaning that the head would advance to the
|
||||
|
|
@ -62,13 +77,95 @@ inline void store_char(unsigned char c, ring_buffer *rx_buffer)
|
|||
}
|
||||
}
|
||||
|
||||
// fixed by Mark Sproul this is on the 644/644p
|
||||
//SIGNAL(SIG_USART_RECV)
|
||||
SIGNAL(USART0_RX_vect)
|
||||
#if defined(USART_RX_vect)
|
||||
SIGNAL(USART_RX_vect)
|
||||
{
|
||||
#if defined(UDR0)
|
||||
unsigned char c = UDR0;
|
||||
#elif defined(UDR)
|
||||
unsigned char c = UDR; // atmega8535
|
||||
#else
|
||||
#error UDR not defined
|
||||
#endif
|
||||
store_char(c, &rx_buffer);
|
||||
}
|
||||
#elif defined(SIG_USART0_RECV) && defined(UDR0)
|
||||
SIGNAL(SIG_USART0_RECV)
|
||||
{
|
||||
unsigned char c = UDR0;
|
||||
store_char(c, &rx_buffer);
|
||||
}
|
||||
#elif defined(SIG_UART0_RECV) && defined(UDR0)
|
||||
SIGNAL(SIG_UART0_RECV)
|
||||
{
|
||||
unsigned char c = UDR0;
|
||||
store_char(c, &rx_buffer);
|
||||
}
|
||||
//#elif defined(SIG_USART_RECV)
|
||||
#elif defined(USART0_RX_vect)
|
||||
// fixed by Mark Sproul this is on the 644/644p
|
||||
//SIGNAL(SIG_USART_RECV)
|
||||
SIGNAL(USART0_RX_vect)
|
||||
{
|
||||
#if defined(UDR0)
|
||||
unsigned char c = UDR0;
|
||||
#elif defined(UDR)
|
||||
unsigned char c = UDR; // atmega8, atmega32
|
||||
#else
|
||||
#error UDR not defined
|
||||
#endif
|
||||
store_char(c, &rx_buffer);
|
||||
}
|
||||
#elif defined(SIG_UART_RECV)
|
||||
// this is for atmega8
|
||||
SIGNAL(SIG_UART_RECV)
|
||||
{
|
||||
#if defined(UDR0)
|
||||
unsigned char c = UDR0; // atmega645
|
||||
#elif defined(UDR)
|
||||
unsigned char c = UDR; // atmega8
|
||||
#endif
|
||||
store_char(c, &rx_buffer);
|
||||
}
|
||||
#elif defined(USBCON)
|
||||
#warning No interrupt handler for usart 0
|
||||
#warning Serial(0) is on USB interface
|
||||
#else
|
||||
#error No interrupt handler for usart 0
|
||||
#endif
|
||||
|
||||
//#if defined(SIG_USART1_RECV)
|
||||
#if defined(USART1_RX_vect)
|
||||
//SIGNAL(SIG_USART1_RECV)
|
||||
SIGNAL(USART1_RX_vect)
|
||||
{
|
||||
unsigned char c = UDR1;
|
||||
store_char(c, &rx_buffer1);
|
||||
}
|
||||
#elif defined(SIG_USART1_RECV)
|
||||
#error SIG_USART1_RECV
|
||||
#endif
|
||||
|
||||
#if defined(USART2_RX_vect) && defined(UDR2)
|
||||
SIGNAL(USART2_RX_vect)
|
||||
{
|
||||
unsigned char c = UDR2;
|
||||
store_char(c, &rx_buffer2);
|
||||
}
|
||||
#elif defined(SIG_USART2_RECV)
|
||||
#error SIG_USART2_RECV
|
||||
#endif
|
||||
|
||||
#if defined(USART3_RX_vect) && defined(UDR3)
|
||||
SIGNAL(USART3_RX_vect)
|
||||
{
|
||||
unsigned char c = UDR3;
|
||||
store_char(c, &rx_buffer3);
|
||||
}
|
||||
#elif defined(SIG_USART3_RECV)
|
||||
#error SIG_USART3_RECV
|
||||
#endif
|
||||
|
||||
|
||||
|
||||
// Constructors ////////////////////////////////////////////////////////////////
|
||||
|
|
@ -134,7 +231,7 @@ void HardwareSerial::end()
|
|||
|
||||
int HardwareSerial::available(void)
|
||||
{
|
||||
return (unsigned int)(RX_BUFFER_SIZE + _rx_buffer->head - _rx_buffer->tail) & (RX_BUFFER_SIZE-1);
|
||||
return (unsigned int)(RX_BUFFER_SIZE + _rx_buffer->head - _rx_buffer->tail) % RX_BUFFER_SIZE;
|
||||
}
|
||||
|
||||
int HardwareSerial::peek(void)
|
||||
|
|
@ -153,7 +250,7 @@ int HardwareSerial::read(void)
|
|||
return -1;
|
||||
} else {
|
||||
unsigned char c = _rx_buffer->buffer[_rx_buffer->tail];
|
||||
_rx_buffer->tail = (unsigned int)(_rx_buffer->tail + 1) & (RX_BUFFER_SIZE-1);
|
||||
_rx_buffer->tail = (unsigned int)(_rx_buffer->tail + 1) % RX_BUFFER_SIZE;
|
||||
return c;
|
||||
}
|
||||
}
|
||||
|
|
@ -181,7 +278,26 @@ void HardwareSerial::write(uint8_t c)
|
|||
}
|
||||
|
||||
// Preinstantiate Objects //////////////////////////////////////////////////////
|
||||
|
||||
#if defined(UBRRH) && defined(UBRRL)
|
||||
HardwareSerial Serial(&rx_buffer, &UBRRH, &UBRRL, &UCSRA, &UCSRB, &UDR, RXEN, TXEN, RXCIE, UDRE, U2X);
|
||||
#elif defined(UBRR0H) && defined(UBRR0L)
|
||||
HardwareSerial Serial(&rx_buffer, &UBRR0H, &UBRR0L, &UCSR0A, &UCSR0B, &UDR0, RXEN0, TXEN0, RXCIE0, UDRE0, U2X0);
|
||||
#elif defined(USBCON)
|
||||
#warning no serial port defined (port 0)
|
||||
#else
|
||||
#error no serial port defined (port 0)
|
||||
#endif
|
||||
|
||||
#if defined(UBRR1H)
|
||||
HardwareSerial Serial1(&rx_buffer1, &UBRR1H, &UBRR1L, &UCSR1A, &UCSR1B, &UDR1, RXEN1, TXEN1, RXCIE1, UDRE1, U2X1);
|
||||
#endif
|
||||
#if defined(UBRR2H)
|
||||
HardwareSerial Serial2(&rx_buffer2, &UBRR2H, &UBRR2L, &UCSR2A, &UCSR2B, &UDR2, RXEN2, TXEN2, RXCIE2, UDRE2, U2X2);
|
||||
#endif
|
||||
#if defined(UBRR3H)
|
||||
HardwareSerial Serial3(&rx_buffer3, &UBRR3H, &UBRR3L, &UCSR3A, &UCSR3B, &UDR3, RXEN3, TXEN3, RXCIE3, UDRE3, U2X3);
|
||||
#endif
|
||||
|
||||
#endif // whole file
|
||||
|
||||
|
|
|
|||
|
|
@ -46,7 +46,6 @@ void attachInterrupt(uint8_t interruptNum, void (*userFunc)(void), int mode) {
|
|||
// the mode into place.
|
||||
|
||||
// Enable the interrupt.
|
||||
|
||||
switch (interruptNum) {
|
||||
#if defined(EICRA) && defined(EICRB) && defined(EIMSK)
|
||||
case 2:
|
||||
|
|
@ -81,6 +80,19 @@ void attachInterrupt(uint8_t interruptNum, void (*userFunc)(void), int mode) {
|
|||
EICRB = (EICRB & ~((1 << ISC70) | (1 << ISC71))) | (mode << ISC70);
|
||||
EIMSK |= (1 << INT7);
|
||||
break;
|
||||
#elif defined(EICRA) && defined(EIMSK)
|
||||
case 0:
|
||||
EICRA = (EICRA & ~((1 << ISC00) | (1 << ISC01))) | (mode << ISC00);
|
||||
EIMSK |= (1 << INT0);
|
||||
break;
|
||||
case 1:
|
||||
EICRA = (EICRA & ~((1 << ISC10) | (1 << ISC11))) | (mode << ISC10);
|
||||
EIMSK |= (1 << INT1);
|
||||
break;
|
||||
case 2:
|
||||
EICRA = (EICRA & ~((1 << ISC20) | (1 << ISC21))) | (mode << ISC20);
|
||||
EIMSK |= (1 << INT2);
|
||||
break;
|
||||
#else
|
||||
case 0:
|
||||
#if defined(EICRA) && defined(ISC00) && defined(EIMSK)
|
||||
|
|
@ -123,15 +135,6 @@ void detachInterrupt(uint8_t interruptNum) {
|
|||
// ATmega8. There, INT0 is 6 and INT1 is 7.)
|
||||
switch (interruptNum) {
|
||||
#if defined(EICRA) && defined(EICRB) && defined(EIMSK)
|
||||
case 2:
|
||||
EIMSK &= ~(1 << INT0);
|
||||
break;
|
||||
case 3:
|
||||
EIMSK &= ~(1 << INT1);
|
||||
break;
|
||||
case 4:
|
||||
EIMSK &= ~(1 << INT2);
|
||||
break;
|
||||
case 5:
|
||||
EIMSK &= ~(1 << INT3);
|
||||
break;
|
||||
|
|
@ -147,6 +150,17 @@ void detachInterrupt(uint8_t interruptNum) {
|
|||
case 7:
|
||||
EIMSK &= ~(1 << INT7);
|
||||
break;
|
||||
#elif defined(EICRA) && defined(EIMSK)
|
||||
case 0:
|
||||
EIMSK &= ~(1 << INT0);
|
||||
break;
|
||||
case 1:
|
||||
EIMSK &= ~(1 << INT1);
|
||||
break;
|
||||
case 2:
|
||||
EIMSK &= ~(1 << INT2);
|
||||
break;
|
||||
|
||||
#else
|
||||
case 0:
|
||||
#if defined(EIMSK) && defined(INT0)
|
||||
|
|
@ -184,8 +198,8 @@ void attachInterruptTwi(void (*userFunc)(void) ) {
|
|||
}
|
||||
*/
|
||||
|
||||
#if defined(EICRA) && defined(EICRB)
|
||||
|
||||
#if defined(EICRA) && defined(EICRB)
|
||||
SIGNAL(INT0_vect) {
|
||||
if(intFunc[EXTERNAL_INT_2])
|
||||
intFunc[EXTERNAL_INT_2]();
|
||||
|
|
@ -226,6 +240,23 @@ SIGNAL(INT7_vect) {
|
|||
intFunc[EXTERNAL_INT_7]();
|
||||
}
|
||||
|
||||
#elif defined(EICRA)
|
||||
|
||||
SIGNAL(INT0_vect) {
|
||||
if(intFunc[EXTERNAL_INT_0])
|
||||
intFunc[EXTERNAL_INT_0]();
|
||||
}
|
||||
|
||||
SIGNAL(INT1_vect) {
|
||||
if(intFunc[EXTERNAL_INT_1])
|
||||
intFunc[EXTERNAL_INT_1]();
|
||||
}
|
||||
|
||||
SIGNAL(INT2_vect) {
|
||||
if(intFunc[EXTERNAL_INT_2])
|
||||
intFunc[EXTERNAL_INT_2]();
|
||||
}
|
||||
|
||||
#else
|
||||
|
||||
SIGNAL(INT0_vect) {
|
||||
|
|
|
|||
|
|
@ -19,17 +19,54 @@
|
|||
Free Software Foundation, Inc., 59 Temple Place, Suite 330,
|
||||
Boston, MA 02111-1307 USA
|
||||
|
||||
$Id: pins_arduino.c 254 2007-04-20 23:17:38Z mellis $
|
||||
Changelog
|
||||
-----------
|
||||
11/25/11 - ryan@ryanmsutton.com - Add pins for Sanguino 644P and 1284P
|
||||
$Id$
|
||||
*/
|
||||
|
||||
#include <avr/io.h>
|
||||
#include "wiring_private.h"
|
||||
#include "pins_arduino.h"
|
||||
|
||||
// On the Sanguino board, digital pins are also used
|
||||
// On the Arduino board, digital pins are also used
|
||||
// for the analog output (software PWM). Analog input
|
||||
// pins are a separate set.
|
||||
|
||||
// ATMEL ATMEGA8 & 168 / ARDUINO
|
||||
//
|
||||
// +-\/-+
|
||||
// PC6 1| |28 PC5 (AI 5)
|
||||
// (D 0) PD0 2| |27 PC4 (AI 4)
|
||||
// (D 1) PD1 3| |26 PC3 (AI 3)
|
||||
// (D 2) PD2 4| |25 PC2 (AI 2)
|
||||
// PWM+ (D 3) PD3 5| |24 PC1 (AI 1)
|
||||
// (D 4) PD4 6| |23 PC0 (AI 0)
|
||||
// VCC 7| |22 GND
|
||||
// GND 8| |21 AREF
|
||||
// PB6 9| |20 AVCC
|
||||
// PB7 10| |19 PB5 (D 13)
|
||||
// PWM+ (D 5) PD5 11| |18 PB4 (D 12)
|
||||
// PWM+ (D 6) PD6 12| |17 PB3 (D 11) PWM
|
||||
// (D 7) PD7 13| |16 PB2 (D 10) PWM
|
||||
// (D 8) PB0 14| |15 PB1 (D 9) PWM
|
||||
// +----+
|
||||
//
|
||||
// (PWM+ indicates the additional PWM pins on the ATmega168.)
|
||||
|
||||
// ATMEL ATMEGA1280 / ARDUINO
|
||||
//
|
||||
// 0-7 PE0-PE7 works
|
||||
// 8-13 PB0-PB5 works
|
||||
// 14-21 PA0-PA7 works
|
||||
// 22-29 PH0-PH7 works
|
||||
// 30-35 PG5-PG0 works
|
||||
// 36-43 PC7-PC0 works
|
||||
// 44-51 PJ7-PJ0 works
|
||||
// 52-59 PL7-PL0 works
|
||||
// 60-67 PD7-PD0 works
|
||||
// A0-A7 PF0-PF7
|
||||
// A8-A15 PK0-PK7
|
||||
// ATMEL ATMEGA644P / SANGUINO
|
||||
//
|
||||
// +---\/---+
|
||||
|
|
@ -55,42 +92,321 @@
|
|||
// PWM (D 14) PD6 20| |21 PD7 (D 15) PWM
|
||||
// +--------+
|
||||
//
|
||||
|
||||
#define PA 1
|
||||
#define PB 2
|
||||
#define PC 3
|
||||
#define PD 4
|
||||
#define PE 5
|
||||
#define PF 6
|
||||
#define PG 7
|
||||
#define PH 8
|
||||
#define PJ 10
|
||||
#define PK 11
|
||||
#define PL 12
|
||||
|
||||
|
||||
#if defined(__AVR_ATmega1280__) || defined(__AVR_ATmega2560__)
|
||||
const uint16_t PROGMEM port_to_mode_PGM[] = {
|
||||
NOT_A_PORT,
|
||||
&DDRA,
|
||||
&DDRB,
|
||||
&DDRC,
|
||||
&DDRD,
|
||||
&DDRE,
|
||||
&DDRF,
|
||||
&DDRG,
|
||||
&DDRH,
|
||||
NOT_A_PORT,
|
||||
&DDRJ,
|
||||
&DDRK,
|
||||
&DDRL,
|
||||
};
|
||||
|
||||
const uint16_t PROGMEM port_to_output_PGM[] = {
|
||||
NOT_A_PORT,
|
||||
&PORTA,
|
||||
&PORTB,
|
||||
&PORTC,
|
||||
&PORTD,
|
||||
&PORTE,
|
||||
&PORTF,
|
||||
&PORTG,
|
||||
&PORTH,
|
||||
NOT_A_PORT,
|
||||
&PORTJ,
|
||||
&PORTK,
|
||||
&PORTL,
|
||||
};
|
||||
|
||||
const uint16_t PROGMEM port_to_input_PGM[] = {
|
||||
NOT_A_PIN,
|
||||
&PINA,
|
||||
&PINB,
|
||||
&PINC,
|
||||
&PIND,
|
||||
&PINE,
|
||||
&PINF,
|
||||
&PING,
|
||||
&PINH,
|
||||
NOT_A_PIN,
|
||||
&PINJ,
|
||||
&PINK,
|
||||
&PINL,
|
||||
};
|
||||
|
||||
const uint8_t PROGMEM digital_pin_to_port_PGM[] = {
|
||||
// PORTLIST
|
||||
// -------------------------------------------
|
||||
PE , // PE 0 ** 0 ** USART0_RX
|
||||
PE , // PE 1 ** 1 ** USART0_TX
|
||||
PE , // PE 4 ** 2 ** PWM2
|
||||
PE , // PE 5 ** 3 ** PWM3
|
||||
PG , // PG 5 ** 4 ** PWM4
|
||||
PE , // PE 3 ** 5 ** PWM5
|
||||
PH , // PH 3 ** 6 ** PWM6
|
||||
PH , // PH 4 ** 7 ** PWM7
|
||||
PH , // PH 5 ** 8 ** PWM8
|
||||
PH , // PH 6 ** 9 ** PWM9
|
||||
PB , // PB 4 ** 10 ** PWM10
|
||||
PB , // PB 5 ** 11 ** PWM11
|
||||
PB , // PB 6 ** 12 ** PWM12
|
||||
PB , // PB 7 ** 13 ** PWM13
|
||||
PJ , // PJ 1 ** 14 ** USART3_TX
|
||||
PJ , // PJ 0 ** 15 ** USART3_RX
|
||||
PH , // PH 1 ** 16 ** USART2_TX
|
||||
PH , // PH 0 ** 17 ** USART2_RX
|
||||
PD , // PD 3 ** 18 ** USART1_TX
|
||||
PD , // PD 2 ** 19 ** USART1_RX
|
||||
PD , // PD 1 ** 20 ** I2C_SDA
|
||||
PD , // PD 0 ** 21 ** I2C_SCL
|
||||
PA , // PA 0 ** 22 ** D22
|
||||
PA , // PA 1 ** 23 ** D23
|
||||
PA , // PA 2 ** 24 ** D24
|
||||
PA , // PA 3 ** 25 ** D25
|
||||
PA , // PA 4 ** 26 ** D26
|
||||
PA , // PA 5 ** 27 ** D27
|
||||
PA , // PA 6 ** 28 ** D28
|
||||
PA , // PA 7 ** 29 ** D29
|
||||
PC , // PC 7 ** 30 ** D30
|
||||
PC , // PC 6 ** 31 ** D31
|
||||
PC , // PC 5 ** 32 ** D32
|
||||
PC , // PC 4 ** 33 ** D33
|
||||
PC , // PC 3 ** 34 ** D34
|
||||
PC , // PC 2 ** 35 ** D35
|
||||
PC , // PC 1 ** 36 ** D36
|
||||
PC , // PC 0 ** 37 ** D37
|
||||
PD , // PD 7 ** 38 ** D38
|
||||
PG , // PG 2 ** 39 ** D39
|
||||
PG , // PG 1 ** 40 ** D40
|
||||
PG , // PG 0 ** 41 ** D41
|
||||
PL , // PL 7 ** 42 ** D42
|
||||
PL , // PL 6 ** 43 ** D43
|
||||
PL , // PL 5 ** 44 ** D44
|
||||
PL , // PL 4 ** 45 ** D45
|
||||
PL , // PL 3 ** 46 ** D46
|
||||
PL , // PL 2 ** 47 ** D47
|
||||
PL , // PL 1 ** 48 ** D48
|
||||
PL , // PL 0 ** 49 ** D49
|
||||
PB , // PB 3 ** 50 ** SPI_MISO
|
||||
PB , // PB 2 ** 51 ** SPI_MOSI
|
||||
PB , // PB 1 ** 52 ** SPI_SCK
|
||||
PB , // PB 0 ** 53 ** SPI_SS
|
||||
PF , // PF 0 ** 54 ** A0
|
||||
PF , // PF 1 ** 55 ** A1
|
||||
PF , // PF 2 ** 56 ** A2
|
||||
PF , // PF 3 ** 57 ** A3
|
||||
PF , // PF 4 ** 58 ** A4
|
||||
PF , // PF 5 ** 59 ** A5
|
||||
PF , // PF 6 ** 60 ** A6
|
||||
PF , // PF 7 ** 61 ** A7
|
||||
PK , // PK 0 ** 62 ** A8
|
||||
PK , // PK 1 ** 63 ** A9
|
||||
PK , // PK 2 ** 64 ** A10
|
||||
PK , // PK 3 ** 65 ** A11
|
||||
PK , // PK 4 ** 66 ** A12
|
||||
PK , // PK 5 ** 67 ** A13
|
||||
PK , // PK 6 ** 68 ** A14
|
||||
PK , // PK 7 ** 69 ** A15
|
||||
};
|
||||
|
||||
const uint8_t PROGMEM digital_pin_to_bit_mask_PGM[] = {
|
||||
// PIN IN PORT
|
||||
// -------------------------------------------
|
||||
_BV( 0 ) , // PE 0 ** 0 ** USART0_RX
|
||||
_BV( 1 ) , // PE 1 ** 1 ** USART0_TX
|
||||
_BV( 4 ) , // PE 4 ** 2 ** PWM2
|
||||
_BV( 5 ) , // PE 5 ** 3 ** PWM3
|
||||
_BV( 5 ) , // PG 5 ** 4 ** PWM4
|
||||
_BV( 3 ) , // PE 3 ** 5 ** PWM5
|
||||
_BV( 3 ) , // PH 3 ** 6 ** PWM6
|
||||
_BV( 4 ) , // PH 4 ** 7 ** PWM7
|
||||
_BV( 5 ) , // PH 5 ** 8 ** PWM8
|
||||
_BV( 6 ) , // PH 6 ** 9 ** PWM9
|
||||
_BV( 4 ) , // PB 4 ** 10 ** PWM10
|
||||
_BV( 5 ) , // PB 5 ** 11 ** PWM11
|
||||
_BV( 6 ) , // PB 6 ** 12 ** PWM12
|
||||
_BV( 7 ) , // PB 7 ** 13 ** PWM13
|
||||
_BV( 1 ) , // PJ 1 ** 14 ** USART3_TX
|
||||
_BV( 0 ) , // PJ 0 ** 15 ** USART3_RX
|
||||
_BV( 1 ) , // PH 1 ** 16 ** USART2_TX
|
||||
_BV( 0 ) , // PH 0 ** 17 ** USART2_RX
|
||||
_BV( 3 ) , // PD 3 ** 18 ** USART1_TX
|
||||
_BV( 2 ) , // PD 2 ** 19 ** USART1_RX
|
||||
_BV( 1 ) , // PD 1 ** 20 ** I2C_SDA
|
||||
_BV( 0 ) , // PD 0 ** 21 ** I2C_SCL
|
||||
_BV( 0 ) , // PA 0 ** 22 ** D22
|
||||
_BV( 1 ) , // PA 1 ** 23 ** D23
|
||||
_BV( 2 ) , // PA 2 ** 24 ** D24
|
||||
_BV( 3 ) , // PA 3 ** 25 ** D25
|
||||
_BV( 4 ) , // PA 4 ** 26 ** D26
|
||||
_BV( 5 ) , // PA 5 ** 27 ** D27
|
||||
_BV( 6 ) , // PA 6 ** 28 ** D28
|
||||
_BV( 7 ) , // PA 7 ** 29 ** D29
|
||||
_BV( 7 ) , // PC 7 ** 30 ** D30
|
||||
_BV( 6 ) , // PC 6 ** 31 ** D31
|
||||
_BV( 5 ) , // PC 5 ** 32 ** D32
|
||||
_BV( 4 ) , // PC 4 ** 33 ** D33
|
||||
_BV( 3 ) , // PC 3 ** 34 ** D34
|
||||
_BV( 2 ) , // PC 2 ** 35 ** D35
|
||||
_BV( 1 ) , // PC 1 ** 36 ** D36
|
||||
_BV( 0 ) , // PC 0 ** 37 ** D37
|
||||
_BV( 7 ) , // PD 7 ** 38 ** D38
|
||||
_BV( 2 ) , // PG 2 ** 39 ** D39
|
||||
_BV( 1 ) , // PG 1 ** 40 ** D40
|
||||
_BV( 0 ) , // PG 0 ** 41 ** D41
|
||||
_BV( 7 ) , // PL 7 ** 42 ** D42
|
||||
_BV( 6 ) , // PL 6 ** 43 ** D43
|
||||
_BV( 5 ) , // PL 5 ** 44 ** D44
|
||||
_BV( 4 ) , // PL 4 ** 45 ** D45
|
||||
_BV( 3 ) , // PL 3 ** 46 ** D46
|
||||
_BV( 2 ) , // PL 2 ** 47 ** D47
|
||||
_BV( 1 ) , // PL 1 ** 48 ** D48
|
||||
_BV( 0 ) , // PL 0 ** 49 ** D49
|
||||
_BV( 3 ) , // PB 3 ** 50 ** SPI_MISO
|
||||
_BV( 2 ) , // PB 2 ** 51 ** SPI_MOSI
|
||||
_BV( 1 ) , // PB 1 ** 52 ** SPI_SCK
|
||||
_BV( 0 ) , // PB 0 ** 53 ** SPI_SS
|
||||
_BV( 0 ) , // PF 0 ** 54 ** A0
|
||||
_BV( 1 ) , // PF 1 ** 55 ** A1
|
||||
_BV( 2 ) , // PF 2 ** 56 ** A2
|
||||
_BV( 3 ) , // PF 3 ** 57 ** A3
|
||||
_BV( 4 ) , // PF 4 ** 58 ** A4
|
||||
_BV( 5 ) , // PF 5 ** 59 ** A5
|
||||
_BV( 6 ) , // PF 6 ** 60 ** A6
|
||||
_BV( 7 ) , // PF 7 ** 61 ** A7
|
||||
_BV( 0 ) , // PK 0 ** 62 ** A8
|
||||
_BV( 1 ) , // PK 1 ** 63 ** A9
|
||||
_BV( 2 ) , // PK 2 ** 64 ** A10
|
||||
_BV( 3 ) , // PK 3 ** 65 ** A11
|
||||
_BV( 4 ) , // PK 4 ** 66 ** A12
|
||||
_BV( 5 ) , // PK 5 ** 67 ** A13
|
||||
_BV( 6 ) , // PK 6 ** 68 ** A14
|
||||
_BV( 7 ) , // PK 7 ** 69 ** A15
|
||||
};
|
||||
|
||||
const uint8_t PROGMEM digital_pin_to_timer_PGM[] = {
|
||||
// TIMERS
|
||||
// -------------------------------------------
|
||||
NOT_ON_TIMER , // PE 0 ** 0 ** USART0_RX
|
||||
NOT_ON_TIMER , // PE 1 ** 1 ** USART0_TX
|
||||
TIMER3B , // PE 4 ** 2 ** PWM2
|
||||
TIMER3C , // PE 5 ** 3 ** PWM3
|
||||
TIMER0B , // PG 5 ** 4 ** PWM4
|
||||
TIMER3A , // PE 3 ** 5 ** PWM5
|
||||
TIMER4A , // PH 3 ** 6 ** PWM6
|
||||
TIMER4B , // PH 4 ** 7 ** PWM7
|
||||
TIMER4C , // PH 5 ** 8 ** PWM8
|
||||
TIMER2B , // PH 6 ** 9 ** PWM9
|
||||
TIMER2A , // PB 4 ** 10 ** PWM10
|
||||
TIMER1A , // PB 5 ** 11 ** PWM11
|
||||
TIMER1B , // PB 6 ** 12 ** PWM12
|
||||
TIMER0A , // PB 7 ** 13 ** PWM13
|
||||
NOT_ON_TIMER , // PJ 1 ** 14 ** USART3_TX
|
||||
NOT_ON_TIMER , // PJ 0 ** 15 ** USART3_RX
|
||||
NOT_ON_TIMER , // PH 1 ** 16 ** USART2_TX
|
||||
NOT_ON_TIMER , // PH 0 ** 17 ** USART2_RX
|
||||
NOT_ON_TIMER , // PD 3 ** 18 ** USART1_TX
|
||||
NOT_ON_TIMER , // PD 2 ** 19 ** USART1_RX
|
||||
NOT_ON_TIMER , // PD 1 ** 20 ** I2C_SDA
|
||||
NOT_ON_TIMER , // PD 0 ** 21 ** I2C_SCL
|
||||
NOT_ON_TIMER , // PA 0 ** 22 ** D22
|
||||
NOT_ON_TIMER , // PA 1 ** 23 ** D23
|
||||
NOT_ON_TIMER , // PA 2 ** 24 ** D24
|
||||
NOT_ON_TIMER , // PA 3 ** 25 ** D25
|
||||
NOT_ON_TIMER , // PA 4 ** 26 ** D26
|
||||
NOT_ON_TIMER , // PA 5 ** 27 ** D27
|
||||
NOT_ON_TIMER , // PA 6 ** 28 ** D28
|
||||
NOT_ON_TIMER , // PA 7 ** 29 ** D29
|
||||
NOT_ON_TIMER , // PC 7 ** 30 ** D30
|
||||
NOT_ON_TIMER , // PC 6 ** 31 ** D31
|
||||
NOT_ON_TIMER , // PC 5 ** 32 ** D32
|
||||
NOT_ON_TIMER , // PC 4 ** 33 ** D33
|
||||
NOT_ON_TIMER , // PC 3 ** 34 ** D34
|
||||
NOT_ON_TIMER , // PC 2 ** 35 ** D35
|
||||
NOT_ON_TIMER , // PC 1 ** 36 ** D36
|
||||
NOT_ON_TIMER , // PC 0 ** 37 ** D37
|
||||
NOT_ON_TIMER , // PD 7 ** 38 ** D38
|
||||
NOT_ON_TIMER , // PG 2 ** 39 ** D39
|
||||
NOT_ON_TIMER , // PG 1 ** 40 ** D40
|
||||
NOT_ON_TIMER , // PG 0 ** 41 ** D41
|
||||
NOT_ON_TIMER , // PL 7 ** 42 ** D42
|
||||
NOT_ON_TIMER , // PL 6 ** 43 ** D43
|
||||
TIMER5C , // PL 5 ** 44 ** D44
|
||||
TIMER5B , // PL 4 ** 45 ** D45
|
||||
TIMER5A , // PL 3 ** 46 ** D46
|
||||
NOT_ON_TIMER , // PL 2 ** 47 ** D47
|
||||
NOT_ON_TIMER , // PL 1 ** 48 ** D48
|
||||
NOT_ON_TIMER , // PL 0 ** 49 ** D49
|
||||
NOT_ON_TIMER , // PB 3 ** 50 ** SPI_MISO
|
||||
NOT_ON_TIMER , // PB 2 ** 51 ** SPI_MOSI
|
||||
NOT_ON_TIMER , // PB 1 ** 52 ** SPI_SCK
|
||||
NOT_ON_TIMER , // PB 0 ** 53 ** SPI_SS
|
||||
NOT_ON_TIMER , // PF 0 ** 54 ** A0
|
||||
NOT_ON_TIMER , // PF 1 ** 55 ** A1
|
||||
NOT_ON_TIMER , // PF 2 ** 56 ** A2
|
||||
NOT_ON_TIMER , // PF 3 ** 57 ** A3
|
||||
NOT_ON_TIMER , // PF 4 ** 58 ** A4
|
||||
NOT_ON_TIMER , // PF 5 ** 59 ** A5
|
||||
NOT_ON_TIMER , // PF 6 ** 60 ** A6
|
||||
NOT_ON_TIMER , // PF 7 ** 61 ** A7
|
||||
NOT_ON_TIMER , // PK 0 ** 62 ** A8
|
||||
NOT_ON_TIMER , // PK 1 ** 63 ** A9
|
||||
NOT_ON_TIMER , // PK 2 ** 64 ** A10
|
||||
NOT_ON_TIMER , // PK 3 ** 65 ** A11
|
||||
NOT_ON_TIMER , // PK 4 ** 66 ** A12
|
||||
NOT_ON_TIMER , // PK 5 ** 67 ** A13
|
||||
NOT_ON_TIMER , // PK 6 ** 68 ** A14
|
||||
NOT_ON_TIMER , // PK 7 ** 69 ** A15
|
||||
};
|
||||
#elif defined(__AVR_ATmega644P__) || defined(__AVR_ATmega1284P__)
|
||||
// these arrays map port names (e.g. port B) to the
|
||||
// appropriate addresses for various functions (e.g. reading
|
||||
// and writing)
|
||||
const uint8_t PROGMEM port_to_mode_PGM[] =
|
||||
const uint16_t PROGMEM port_to_mode_PGM[] =
|
||||
{
|
||||
NOT_A_PORT,
|
||||
(uint8_t) (uint16_t) &DDRA,
|
||||
(uint8_t) (uint16_t) &DDRB,
|
||||
(uint8_t) (uint16_t) &DDRC,
|
||||
(uint8_t) (uint16_t) &DDRD,
|
||||
&DDRA,
|
||||
&DDRB,
|
||||
&DDRC,
|
||||
&DDRD,
|
||||
};
|
||||
|
||||
const uint8_t PROGMEM port_to_output_PGM[] =
|
||||
const uint16_t PROGMEM port_to_output_PGM[] =
|
||||
{
|
||||
NOT_A_PORT,
|
||||
(uint8_t) (uint16_t) &PORTA,
|
||||
(uint8_t) (uint16_t) &PORTB,
|
||||
(uint8_t) (uint16_t) &PORTC,
|
||||
(uint8_t) (uint16_t) &PORTD,
|
||||
&PORTA,
|
||||
&PORTB,
|
||||
&PORTC,
|
||||
&PORTD,
|
||||
};
|
||||
|
||||
const uint8_t PROGMEM port_to_input_PGM[] =
|
||||
const uint16_t PROGMEM port_to_input_PGM[] =
|
||||
{
|
||||
NOT_A_PORT,
|
||||
(uint8_t) (uint16_t) &PINA,
|
||||
(uint8_t) (uint16_t) &PINB,
|
||||
(uint8_t) (uint16_t) &PINC,
|
||||
(uint8_t) (uint16_t) &PIND,
|
||||
&PINA,
|
||||
&PINB,
|
||||
&PINC,
|
||||
&PIND,
|
||||
};
|
||||
|
||||
const uint8_t PROGMEM digital_pin_to_port_PGM[] =
|
||||
{
|
||||
PB, /* 0 */
|
||||
|
|
@ -126,7 +442,6 @@ const uint8_t PROGMEM digital_pin_to_port_PGM[] =
|
|||
PA,
|
||||
PA /* 31 */
|
||||
};
|
||||
|
||||
const uint8_t PROGMEM digital_pin_to_bit_mask_PGM[] =
|
||||
{
|
||||
_BV(0), /* 0, port B */
|
||||
|
|
@ -162,7 +477,6 @@ const uint8_t PROGMEM digital_pin_to_bit_mask_PGM[] =
|
|||
_BV(1),
|
||||
_BV(0)
|
||||
};
|
||||
|
||||
const uint8_t PROGMEM digital_pin_to_timer_PGM[] =
|
||||
{
|
||||
NOT_ON_TIMER, /* 0 - PB0 */
|
||||
|
|
@ -198,3 +512,116 @@ const uint8_t PROGMEM digital_pin_to_timer_PGM[] =
|
|||
NOT_ON_TIMER, /* 30 - PA6 */
|
||||
NOT_ON_TIMER /* 31 - PA7 */
|
||||
};
|
||||
|
||||
#else
|
||||
// these arrays map port names (e.g. port B) to the
|
||||
// appropriate addresses for various functions (e.g. reading
|
||||
// and writing)
|
||||
const uint16_t PROGMEM port_to_mode_PGM[] = {
|
||||
NOT_A_PORT,
|
||||
NOT_A_PORT,
|
||||
&DDRB,
|
||||
&DDRC,
|
||||
&DDRD,
|
||||
};
|
||||
|
||||
const uint16_t PROGMEM port_to_output_PGM[] = {
|
||||
NOT_A_PORT,
|
||||
NOT_A_PORT,
|
||||
&PORTB,
|
||||
&PORTC,
|
||||
&PORTD,
|
||||
};
|
||||
|
||||
const uint16_t PROGMEM port_to_input_PGM[] = {
|
||||
NOT_A_PORT,
|
||||
NOT_A_PORT,
|
||||
&PINB,
|
||||
&PINC,
|
||||
&PIND,
|
||||
};
|
||||
|
||||
const uint8_t PROGMEM digital_pin_to_port_PGM[] = {
|
||||
PD, /* 0 */
|
||||
PD,
|
||||
PD,
|
||||
PD,
|
||||
PD,
|
||||
PD,
|
||||
PD,
|
||||
PD,
|
||||
PB, /* 8 */
|
||||
PB,
|
||||
PB,
|
||||
PB,
|
||||
PB,
|
||||
PB,
|
||||
PC, /* 14 */
|
||||
PC,
|
||||
PC,
|
||||
PC,
|
||||
PC,
|
||||
PC,
|
||||
};
|
||||
|
||||
const uint8_t PROGMEM digital_pin_to_bit_mask_PGM[] = {
|
||||
_BV(0), /* 0, port D */
|
||||
_BV(1),
|
||||
_BV(2),
|
||||
_BV(3),
|
||||
_BV(4),
|
||||
_BV(5),
|
||||
_BV(6),
|
||||
_BV(7),
|
||||
_BV(0), /* 8, port B */
|
||||
_BV(1),
|
||||
_BV(2),
|
||||
_BV(3),
|
||||
_BV(4),
|
||||
_BV(5),
|
||||
_BV(0), /* 14, port C */
|
||||
_BV(1),
|
||||
_BV(2),
|
||||
_BV(3),
|
||||
_BV(4),
|
||||
_BV(5),
|
||||
};
|
||||
|
||||
const uint8_t PROGMEM digital_pin_to_timer_PGM[] = {
|
||||
NOT_ON_TIMER, /* 0 - port D */
|
||||
NOT_ON_TIMER,
|
||||
NOT_ON_TIMER,
|
||||
// on the ATmega168, digital pin 3 has hardware pwm
|
||||
#if defined(__AVR_ATmega8__)
|
||||
NOT_ON_TIMER,
|
||||
#else
|
||||
TIMER2B,
|
||||
#endif
|
||||
NOT_ON_TIMER,
|
||||
// on the ATmega168, digital pins 5 and 6 have hardware pwm
|
||||
#if defined(__AVR_ATmega8__)
|
||||
NOT_ON_TIMER,
|
||||
NOT_ON_TIMER,
|
||||
#else
|
||||
TIMER0B,
|
||||
TIMER0A,
|
||||
#endif
|
||||
NOT_ON_TIMER,
|
||||
NOT_ON_TIMER, /* 8 - port B */
|
||||
TIMER1A,
|
||||
TIMER1B,
|
||||
#if defined(__AVR_ATmega8__)
|
||||
TIMER2,
|
||||
#else
|
||||
TIMER2A,
|
||||
#endif
|
||||
NOT_ON_TIMER,
|
||||
NOT_ON_TIMER,
|
||||
NOT_ON_TIMER,
|
||||
NOT_ON_TIMER, /* 14 - port C */
|
||||
NOT_ON_TIMER,
|
||||
NOT_ON_TIMER,
|
||||
NOT_ON_TIMER,
|
||||
NOT_ON_TIMER,
|
||||
};
|
||||
#endif
|
||||
|
|
|
|||
|
|
@ -39,19 +39,43 @@
|
|||
#define TIMER2A 6
|
||||
#define TIMER2B 7
|
||||
|
||||
#define TIMER3A 8
|
||||
#define TIMER3B 9
|
||||
#define TIMER3C 10
|
||||
#define TIMER4A 11
|
||||
#define TIMER4B 12
|
||||
#define TIMER4C 13
|
||||
#define TIMER5A 14
|
||||
#define TIMER5B 15
|
||||
#define TIMER5C 16
|
||||
|
||||
#if defined(__AVR_ATmega1280__) || defined(__AVR_ATmega2560__)
|
||||
const static uint8_t SS = 53;
|
||||
const static uint8_t MOSI = 51;
|
||||
const static uint8_t MISO = 50;
|
||||
const static uint8_t SCK = 52;
|
||||
#elif defined(__AVR_ATmega644P__) || defined(__AVR_ATmega1284P__)
|
||||
const static uint8_t SS = 4;
|
||||
const static uint8_t MOSI = 5;
|
||||
const static uint8_t MISO = 6;
|
||||
const static uint8_t SCK = 7;
|
||||
|
||||
extern const uint8_t PROGMEM port_to_mode_PGM[];
|
||||
extern const uint8_t PROGMEM port_to_input_PGM[];
|
||||
extern const uint8_t PROGMEM port_to_output_PGM[];
|
||||
#else
|
||||
const static uint8_t SS = 10;
|
||||
const static uint8_t MOSI = 11;
|
||||
const static uint8_t MISO = 12;
|
||||
const static uint8_t SCK = 13;
|
||||
#endif
|
||||
|
||||
// On the ATmega1280, the addresses of some of the port registers are
|
||||
// greater than 255, so we can't store them in uint8_t's.
|
||||
extern const uint16_t PROGMEM port_to_mode_PGM[];
|
||||
extern const uint16_t PROGMEM port_to_input_PGM[];
|
||||
extern const uint16_t PROGMEM port_to_output_PGM[];
|
||||
|
||||
extern const uint8_t PROGMEM digital_pin_to_port_PGM[];
|
||||
extern const uint8_t PROGMEM digital_pin_to_bit_PGM[];
|
||||
// extern const uint8_t PROGMEM digital_pin_to_bit_PGM[];
|
||||
extern const uint8_t PROGMEM digital_pin_to_bit_mask_PGM[];
|
||||
|
||||
extern const uint8_t PROGMEM digital_pin_to_timer_PGM[];
|
||||
|
||||
// Get the bit location within the hardware port of the given virtual pin.
|
||||
|
|
@ -63,8 +87,8 @@ extern const uint8_t PROGMEM digital_pin_to_timer_PGM[];
|
|||
#define digitalPinToBitMask(P) ( pgm_read_byte( digital_pin_to_bit_mask_PGM + (P) ) )
|
||||
#define digitalPinToTimer(P) ( pgm_read_byte( digital_pin_to_timer_PGM + (P) ) )
|
||||
#define analogInPinToBit(P) (P)
|
||||
#define portOutputRegister(P) ( (volatile uint8_t *)( (uint16_t) pgm_read_byte( port_to_output_PGM + (P))) )
|
||||
#define portInputRegister(P) ( (volatile uint8_t *)( (uint16_t) pgm_read_byte( port_to_input_PGM + (P))) )
|
||||
#define portModeRegister(P) ( (volatile uint8_t *)( (uint16_t) pgm_read_byte( port_to_mode_PGM + (P))) )
|
||||
#define portOutputRegister(P) ( (volatile uint8_t *)( pgm_read_word( port_to_output_PGM + (P))) )
|
||||
#define portInputRegister(P) ( (volatile uint8_t *)( pgm_read_word( port_to_input_PGM + (P))) )
|
||||
#define portModeRegister(P) ( (volatile uint8_t *)( pgm_read_word( port_to_mode_PGM + (P))) )
|
||||
|
||||
#endif
|
||||
|
|
|
|||
|
|
@ -25,7 +25,6 @@
|
|||
#ifndef Wiring_h
|
||||
#define Wiring_h
|
||||
|
||||
#include <math.h>
|
||||
#include <avr/io.h>
|
||||
#include <stdlib.h>
|
||||
#include "binary.h"
|
||||
|
|
@ -77,7 +76,10 @@ extern "C"{
|
|||
#define max(a,b) ((a)>(b)?(a):(b))
|
||||
#define abs(x) ((x)>0?(x):-(x))
|
||||
#define constrain(amt,low,high) ((amt)<(low)?(low):((amt)>(high)?(high):(amt)))
|
||||
#define round(x) ((x)>=0?(long)((x)+0.5):(long)((x)-0.5))
|
||||
|
||||
// Removed to work with newer AVRLIBC
|
||||
//#define round(x) ((x)>=0?(long)((x)+0.5):(long)((x)-0.5))
|
||||
|
||||
#define radians(deg) ((deg)*DEG_TO_RAD)
|
||||
#define degrees(rad) ((rad)*RAD_TO_DEG)
|
||||
#define sq(x) ((x)*(x))
|
||||
|
|
|
|||
|
|
@ -24,10 +24,10 @@
|
|||
|
||||
#ifndef WiringPrivate_h
|
||||
#define WiringPrivate_h
|
||||
#include <math.h>
|
||||
|
||||
#include <avr/io.h>
|
||||
#include <avr/interrupt.h>
|
||||
#include <util/delay.h>
|
||||
#include <avr/delay.h>
|
||||
#include <stdio.h>
|
||||
#include <stdarg.h>
|
||||
|
||||
|
|
@ -55,6 +55,8 @@ extern "C"{
|
|||
|
||||
#if defined(__AVR_ATmega1280__) || defined(__AVR_ATmega2560__)
|
||||
#define EXTERNAL_NUM_INTERRUPTS 8
|
||||
#elif defined(__AVR_ATmega644P__) || defined(__AVR_ATmega1284P__)
|
||||
#define EXTERNAL_NUM_INTERRUPTS 3
|
||||
#else
|
||||
#define EXTERNAL_NUM_INTERRUPTS 2
|
||||
#endif
|
||||
|
|
|
|||
Loading…
Reference in a new issue