diff --git a/Marlin/Conditionals.h b/Marlin/Conditionals.h index bf1886277c..d896880622 100644 --- a/Marlin/Conditionals.h +++ b/Marlin/Conditionals.h @@ -5,7 +5,16 @@ #ifndef CONDITIONALS_H #define CONDITIONALS_H - #include "Arduino.h" + #ifndef AT90USB + #define HardwareSerial_h // trick to disable the standard HWserial + #endif + + #if (ARDUINO >= 100) + #include "Arduino.h" + #else + #include "WProgram.h" + #endif + #include "pins.h" /** @@ -39,159 +48,6 @@ #define QUICK_HOME //SCARA needs Quickhome #endif - - /** - * LCD Controllers - */ - - #if defined (MAKRPANEL) - #define DOGLCD - #define SDSUPPORT - #define ULTIPANEL - #define NEWPANEL - #define DEFAULT_LCD_CONTRAST 17 - #endif - - #if defined(miniVIKI) || defined(VIKI2) - #define ULTRA_LCD //general LCD support, also 16x2 - #define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family) - #define ULTIMAKERCONTROLLER //as available from the Ultimaker online store. - - #ifdef miniVIKI - #define DEFAULT_LCD_CONTRAST 95 - #else - #define DEFAULT_LCD_CONTRAST 40 - #endif - - #define ENCODER_PULSES_PER_STEP 4 - #define ENCODER_STEPS_PER_MENU_ITEM 1 - #endif - - #ifdef PANEL_ONE - #define SDSUPPORT - #define ULTIMAKERCONTROLLER - #endif - - #ifdef REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER - #define DOGLCD - #define U8GLIB_ST7920 - #define REPRAP_DISCOUNT_SMART_CONTROLLER - #endif - - #if defined(ULTIMAKERCONTROLLER) || defined(REPRAP_DISCOUNT_SMART_CONTROLLER) || defined(G3D_PANEL) - #define ULTIPANEL - #define NEWPANEL - #endif - - #ifdef REPRAPWORLD_KEYPAD - #define NEWPANEL - #define ULTIPANEL - #endif - - #ifdef RA_CONTROL_PANEL - #define ULTIPANEL - #define NEWPANEL - #define LCD_I2C_TYPE_PCA8574 - #define LCD_I2C_ADDRESS 0x27 // I2C Address of the port expander - #endif - - /** - * I2C PANELS - */ - - #ifdef LCD_I2C_SAINSMART_YWROBOT - // This uses the LiquidCrystal_I2C library ( https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home ) - // Make sure it is placed in the Arduino libraries directory. - #define LCD_I2C_TYPE_PCF8575 - #define LCD_I2C_ADDRESS 0x27 // I2C Address of the port expander - #define NEWPANEL - #define ULTIPANEL - #endif - - // PANELOLU2 LCD with status LEDs, separate encoder and click inputs - #ifdef LCD_I2C_PANELOLU2 - // This uses the LiquidTWI2 library v1.2.3 or later ( https://github.com/lincomatic/LiquidTWI2 ) - // Make sure the LiquidTWI2 directory is placed in the Arduino or Sketchbook libraries subdirectory. - // (v1.2.3 no longer requires you to define PANELOLU in the LiquidTWI2.h library header file) - // Note: The PANELOLU2 encoder click input can either be directly connected to a pin - // (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1). - #define LCD_I2C_TYPE_MCP23017 - #define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander - #define LCD_USE_I2C_BUZZER //comment out to disable buzzer on LCD - #define NEWPANEL - #define ULTIPANEL - - #ifndef ENCODER_PULSES_PER_STEP - #define ENCODER_PULSES_PER_STEP 4 - #endif - - #ifndef ENCODER_STEPS_PER_MENU_ITEM - #define ENCODER_STEPS_PER_MENU_ITEM 1 - #endif - - - #ifdef LCD_USE_I2C_BUZZER - #define LCD_FEEDBACK_FREQUENCY_HZ 1000 - #define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 - #endif - - #endif - - // Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs - #ifdef LCD_I2C_VIKI - // This uses the LiquidTWI2 library v1.2.3 or later ( https://github.com/lincomatic/LiquidTWI2 ) - // Make sure the LiquidTWI2 directory is placed in the Arduino or Sketchbook libraries subdirectory. - // Note: The pause/stop/resume LCD button pin should be connected to the Arduino - // BTN_ENC pin (or set BTN_ENC to -1 if not used) - #define LCD_I2C_TYPE_MCP23017 - #define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander - #define LCD_USE_I2C_BUZZER //comment out to disable buzzer on LCD (requires LiquidTWI2 v1.2.3 or later) - #define NEWPANEL - #define ULTIPANEL - #endif - - // Shift register panels - // --------------------- - // 2 wire Non-latching LCD SR from: - // https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection - - #ifdef SAV_3DLCD - #define SR_LCD_2W_NL // Non latching 2 wire shiftregister - #define NEWPANEL - #define ULTIPANEL - #endif - - - #ifdef ULTIPANEL - #define NEWPANEL //enable this if you have a click-encoder panel - #define SDSUPPORT - #define ULTRA_LCD - #ifdef DOGLCD // Change number of lines to match the DOG graphic display - #define LCD_WIDTH 22 - #define LCD_HEIGHT 5 - #else - #define LCD_WIDTH 20 - #define LCD_HEIGHT 4 - #endif - #else //no panel but just LCD - #ifdef ULTRA_LCD - #ifdef DOGLCD // Change number of lines to match the 128x64 graphics display - #define LCD_WIDTH 22 - #define LCD_HEIGHT 5 - #else - #define LCD_WIDTH 16 - #define LCD_HEIGHT 2 - #endif - #endif - #endif - - /** - * Default LCD contrast for dogm-like LCD displays - */ - #if defined(DOGLCD) && !defined(DEFAULT_LCD_CONTRAST) - #define DEFAULT_LCD_CONTRAST 32 - #endif - /** * AUTOSET LOCATIONS OF LIMIT SWITCHES * Added by ZetaPhoenix 09-15-2012 diff --git a/Marlin/Conditionals_lcd.h b/Marlin/Conditionals_lcd.h new file mode 100644 index 0000000000..6e63934b11 --- /dev/null +++ b/Marlin/Conditionals_lcd.h @@ -0,0 +1,155 @@ +/** + * Conditionals_lcd.h + * LCD-oriented defines that depend on configuration. + */ +#ifndef CONDITIONALS_LCD_H + #define CONDITIONALS_LCD_H + + #if defined(MAKRPANEL) + #define DOGLCD + #define SDSUPPORT + #define DEFAULT_LCD_CONTRAST 17 + #define ULTIPANEL + #define NEWPANEL + #endif + + #if defined(miniVIKI) || defined(VIKI2) + #define ULTRA_LCD //general LCD support, also 16x2 + #define DOGLCD // Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family) + #define ULTIMAKERCONTROLLER //as available from the Ultimaker online store. + + #ifdef miniVIKI + #define DEFAULT_LCD_CONTRAST 95 + #else + #define DEFAULT_LCD_CONTRAST 40 + #endif + + #define ENCODER_PULSES_PER_STEP 4 + #define ENCODER_STEPS_PER_MENU_ITEM 1 + #endif + + #ifdef PANEL_ONE + #define SDSUPPORT + #define ULTIMAKERCONTROLLER + #endif + + #ifdef REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER + #define DOGLCD + #define U8GLIB_ST7920 + #define REPRAP_DISCOUNT_SMART_CONTROLLER + #endif + + #if defined(ULTIMAKERCONTROLLER) || defined(REPRAP_DISCOUNT_SMART_CONTROLLER) || defined(G3D_PANEL) + #define ULTIPANEL + #define NEWPANEL + #endif + + #ifdef REPRAPWORLD_KEYPAD + #define ULTIPANEL + #define NEWPANEL + #endif + + #ifdef RA_CONTROL_PANEL + #define LCD_I2C_TYPE_PCA8574 + #define LCD_I2C_ADDRESS 0x27 // I2C Address of the port expander + #define ULTIPANEL + #define NEWPANEL + #endif + + /** + * I2C PANELS + */ + + #ifdef LCD_I2C_SAINSMART_YWROBOT + // This uses the LiquidCrystal_I2C library ( https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home ) + // Make sure it is placed in the Arduino libraries directory. + #define LCD_I2C_TYPE_PCF8575 + #define LCD_I2C_ADDRESS 0x27 // I2C Address of the port expander + #define ULTIPANEL + #define NEWPANEL + #endif + + // PANELOLU2 LCD with status LEDs, separate encoder and click inputs + #ifdef LCD_I2C_PANELOLU2 + // This uses the LiquidTWI2 library v1.2.3 or later ( https://github.com/lincomatic/LiquidTWI2 ) + // Make sure the LiquidTWI2 directory is placed in the Arduino or Sketchbook libraries subdirectory. + // (v1.2.3 no longer requires you to define PANELOLU in the LiquidTWI2.h library header file) + // Note: The PANELOLU2 encoder click input can either be directly connected to a pin + // (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1). + #define LCD_I2C_TYPE_MCP23017 + #define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander + #define LCD_USE_I2C_BUZZER //comment out to disable buzzer on LCD + + #ifndef ENCODER_PULSES_PER_STEP + #define ENCODER_PULSES_PER_STEP 4 + #endif + + #ifndef ENCODER_STEPS_PER_MENU_ITEM + #define ENCODER_STEPS_PER_MENU_ITEM 1 + #endif + + #ifdef LCD_USE_I2C_BUZZER + #define LCD_FEEDBACK_FREQUENCY_HZ 1000 + #define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 + #endif + + #define ULTIPANEL + #define NEWPANEL + #endif + + // Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs + #ifdef LCD_I2C_VIKI + // This uses the LiquidTWI2 library v1.2.3 or later ( https://github.com/lincomatic/LiquidTWI2 ) + // Make sure the LiquidTWI2 directory is placed in the Arduino or Sketchbook libraries subdirectory. + // Note: The pause/stop/resume LCD button pin should be connected to the Arduino + // BTN_ENC pin (or set BTN_ENC to -1 if not used) + #define LCD_I2C_TYPE_MCP23017 + #define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander + #define LCD_USE_I2C_BUZZER //comment out to disable buzzer on LCD (requires LiquidTWI2 v1.2.3 or later) + #define ULTIPANEL + #define NEWPANEL + #endif + + // Shift register panels + // --------------------- + // 2 wire Non-latching LCD SR from: + // https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection + + #ifdef SAV_3DLCD + #define SR_LCD_2W_NL // Non latching 2 wire shiftregister + #define ULTIPANEL + #define NEWPANEL + #endif + + + #ifdef ULTIPANEL + #define NEWPANEL //enable this if you have a click-encoder panel + #define SDSUPPORT + #define ULTRA_LCD + #ifdef DOGLCD // Change number of lines to match the DOG graphic display + #define LCD_WIDTH 22 + #define LCD_HEIGHT 5 + #else + #define LCD_WIDTH 20 + #define LCD_HEIGHT 4 + #endif + #else //no panel but just LCD + #ifdef ULTRA_LCD + #ifdef DOGLCD // Change number of lines to match the 128x64 graphics display + #define LCD_WIDTH 22 + #define LCD_HEIGHT 5 + #else + #define LCD_WIDTH 16 + #define LCD_HEIGHT 2 + #endif + #endif + #endif + + /** + * Default LCD contrast for dogm-like LCD displays + */ + #if defined(DOGLCD) && !defined(DEFAULT_LCD_CONTRAST) + #define DEFAULT_LCD_CONTRAST 32 + #endif + +#endif //CONDITIONALS_LCD_H diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h index 3c5d92deee..bb753eaa43 100644 --- a/Marlin/Configuration.h +++ b/Marlin/Configuration.h @@ -713,6 +713,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o +#include "Conditionals_lcd.h" #include "Configuration_adv.h" #include "Conditionals.h" #include "SanityCheck.h" diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h index 42cf4d28b2..0435a02c49 100644 --- a/Marlin/Configuration_adv.h +++ b/Marlin/Configuration_adv.h @@ -110,41 +110,41 @@ // allowing faster printing speeds. //#define DUAL_X_CARRIAGE #ifdef DUAL_X_CARRIAGE -// Configuration for second X-carriage -// Note: the first x-carriage is defined as the x-carriage which homes to the minimum endstop; -// the second x-carriage always homes to the maximum endstop. -#define X2_MIN_POS 80 // set minimum to ensure second x-carriage doesn't hit the parked first X-carriage -#define X2_MAX_POS 353 // set maximum to the distance between toolheads when both heads are homed -#define X2_HOME_DIR 1 // the second X-carriage always homes to the maximum endstop position -#define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position - // However: In this mode the EXTRUDER_OFFSET_X value for the second extruder provides a software - // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops - // without modifying the firmware (through the "M218 T1 X???" command). - // Remember: you should set the second extruder x-offset to 0 in your slicer. + // Configuration for second X-carriage + // Note: the first x-carriage is defined as the x-carriage which homes to the minimum endstop; + // the second x-carriage always homes to the maximum endstop. + #define X2_MIN_POS 80 // set minimum to ensure second x-carriage doesn't hit the parked first X-carriage + #define X2_MAX_POS 353 // set maximum to the distance between toolheads when both heads are homed + #define X2_HOME_DIR 1 // the second X-carriage always homes to the maximum endstop position + #define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position + // However: In this mode the EXTRUDER_OFFSET_X value for the second extruder provides a software + // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops + // without modifying the firmware (through the "M218 T1 X???" command). + // Remember: you should set the second extruder x-offset to 0 in your slicer. -// Pins for second x-carriage stepper driver (defined here to avoid further complicating pins.h) -#define X2_ENABLE_PIN 29 -#define X2_STEP_PIN 25 -#define X2_DIR_PIN 23 + // Pins for second x-carriage stepper driver (defined here to avoid further complicating pins.h) + #define X2_ENABLE_PIN 29 + #define X2_STEP_PIN 25 + #define X2_DIR_PIN 23 -// There are a few selectable movement modes for dual x-carriages using M605 S -// Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results -// as long as it supports dual x-carriages. (M605 S0) -// Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so -// that additional slicer support is not required. (M605 S1) -// Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all -// actions of the first x-carriage. This allows the printer to print 2 arbitrary items at -// once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) + // There are a few selectable movement modes for dual x-carriages using M605 S + // Mode 0: Full control. The slicer has full control over both x-carriages and can achieve optimal travel results + // as long as it supports dual x-carriages. (M605 S0) + // Mode 1: Auto-park mode. The firmware will automatically park and unpark the x-carriages on tool changes so + // that additional slicer support is not required. (M605 S1) + // Mode 2: Duplication mode. The firmware will transparently make the second x-carriage and extruder copy all + // actions of the first x-carriage. This allows the printer to print 2 arbitrary items at + // once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm]) -// This is the default power-up mode which can be later using M605. -#define DEFAULT_DUAL_X_CARRIAGE_MODE 0 + // This is the default power-up mode which can be later using M605. + #define DEFAULT_DUAL_X_CARRIAGE_MODE 0 -// Default settings in "Auto-park Mode" -#define TOOLCHANGE_PARK_ZLIFT 0.2 // the distance to raise Z axis when parking an extruder -#define TOOLCHANGE_UNPARK_ZLIFT 1 // the distance to raise Z axis when unparking an extruder + // Default settings in "Auto-park Mode" + #define TOOLCHANGE_PARK_ZLIFT 0.2 // the distance to raise Z axis when parking an extruder + #define TOOLCHANGE_UNPARK_ZLIFT 1 // the distance to raise Z axis when unparking an extruder -// Default x offset in duplication mode (typically set to half print bed width) -#define DEFAULT_DUPLICATION_X_OFFSET 100 + // Default x offset in duplication mode (typically set to half print bed width) + #define DEFAULT_DUPLICATION_X_OFFSET 100 #endif //DUAL_X_CARRIAGE @@ -163,20 +163,15 @@ #define INVERT_Z_STEP_PIN false #define INVERT_E_STEP_PIN false -//default stepper release if idle. Set to 0 to deactivate. +// Default stepper release if idle. Set to 0 to deactivate. #define DEFAULT_STEPPER_DEACTIVE_TIME 60 #define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate #define DEFAULT_MINTRAVELFEEDRATE 0.0 -// Feedrates for manual moves along X, Y, Z, E from panel #ifdef ULTIPANEL - #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // set the speeds for manual moves (mm/min) -#endif - -//Comment to disable setting feedrate multiplier via encoder -#ifdef ULTIPANEL - #define ULTIPANEL_FEEDMULTIPLY + #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel + #define ULTIPANEL_FEEDMULTIPLY // Comment to disable setting feedrate multiplier via encoder #endif // minimum time in microseconds that a movement needs to take if the buffer is emptied. @@ -301,7 +296,7 @@ const unsigned int dropsegments=5; //everything with less than this number of st // The number of linear motions that can be in the plan at any give time. // THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2, i.g. 8,16,32 because shifts and ors are used to do the ring-buffering. -#if defined SDSUPPORT +#ifdef SDSUPPORT #define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller #else #define BLOCK_BUFFER_SIZE 16 // maximize block buffer @@ -331,9 +326,9 @@ const unsigned int dropsegments=5; //everything with less than this number of st #define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s) #endif -//adds support for experimental filament exchange support M600; requires display +// Add support for experimental filament exchange support M600; requires display #ifdef ULTIPANEL - #define FILAMENTCHANGEENABLE + //#define FILAMENTCHANGEENABLE #ifdef FILAMENTCHANGEENABLE #define FILAMENTCHANGE_XPOS 3 #define FILAMENTCHANGE_YPOS 3 diff --git a/Marlin/Marlin.h b/Marlin/Marlin.h index 44a85f78df..7cabcbca03 100644 --- a/Marlin/Marlin.h +++ b/Marlin/Marlin.h @@ -20,11 +20,6 @@ #include "fastio.h" #include "Configuration.h" -#include "pins.h" - -#ifndef AT90USB - #define HardwareSerial_h // trick to disable the standard HWserial -#endif #if (ARDUINO >= 100) #include "Arduino.h" @@ -191,17 +186,17 @@ void ClearToSend(); void get_coordinates(); #ifdef DELTA -void calculate_delta(float cartesian[3]); + void calculate_delta(float cartesian[3]); #ifdef ENABLE_AUTO_BED_LEVELING - extern int delta_grid_spacing[2]; - void adjust_delta(float cartesian[3]); + extern int delta_grid_spacing[2]; + void adjust_delta(float cartesian[3]); #endif -extern float delta[3]; -void prepare_move_raw(); + extern float delta[3]; + void prepare_move_raw(); #endif #ifdef SCARA -void calculate_delta(float cartesian[3]); -void calculate_SCARA_forward_Transform(float f_scara[3]); + void calculate_delta(float cartesian[3]); + void calculate_SCARA_forward_Transform(float f_scara[3]); #endif void reset_bed_level(); void prepare_move(); @@ -209,7 +204,7 @@ void kill(); void Stop(); #ifdef FILAMENT_RUNOUT_SENSOR -void filrunout(); + void filrunout(); #endif bool IsStopped(); @@ -223,7 +218,7 @@ void clamp_to_software_endstops(float target[3]); void refresh_cmd_timeout(void); #ifdef FAST_PWM_FAN -void setPwmFrequency(uint8_t pin, int val); + void setPwmFrequency(uint8_t pin, int val); #endif #ifndef CRITICAL_SECTION_START @@ -242,14 +237,14 @@ extern float volumetric_multiplier[EXTRUDERS]; // reciprocal of cross-sectional extern float current_position[NUM_AXIS] ; extern float add_homing[3]; #ifdef DELTA -extern float endstop_adj[3]; -extern float delta_radius; -extern float delta_diagonal_rod; -extern float delta_segments_per_second; -void recalc_delta_settings(float radius, float diagonal_rod); + extern float endstop_adj[3]; + extern float delta_radius; + extern float delta_diagonal_rod; + extern float delta_segments_per_second; + void recalc_delta_settings(float radius, float diagonal_rod); #endif #ifdef SCARA -extern float axis_scaling[3]; // Build size scaling + extern float axis_scaling[3]; // Build size scaling #endif extern float min_pos[3]; extern float max_pos[3]; @@ -257,12 +252,12 @@ extern bool axis_known_position[3]; extern float zprobe_zoffset; extern int fanSpeed; #ifdef BARICUDA -extern int ValvePressure; -extern int EtoPPressure; + extern int ValvePressure; + extern int EtoPPressure; #endif #ifdef FAN_SOFT_PWM -extern unsigned char fanSpeedSoftPwm; + extern unsigned char fanSpeedSoftPwm; #endif #ifdef FILAMENT_SENSOR @@ -276,10 +271,10 @@ extern unsigned char fanSpeedSoftPwm; #endif #ifdef FWRETRACT -extern bool autoretract_enabled; -extern bool retracted[EXTRUDERS]; -extern float retract_length, retract_length_swap, retract_feedrate, retract_zlift; -extern float retract_recover_length, retract_recover_length_swap, retract_recover_feedrate; + extern bool autoretract_enabled; + extern bool retracted[EXTRUDERS]; + extern float retract_length, retract_length_swap, retract_feedrate, retract_zlift; + extern float retract_recover_length, retract_recover_length_swap, retract_recover_feedrate; #endif extern unsigned long starttime; @@ -289,11 +284,10 @@ extern unsigned long stoptime; extern uint8_t active_extruder; #ifdef DIGIPOT_I2C -extern void digipot_i2c_set_current( int channel, float current ); -extern void digipot_i2c_init(); -#endif - + extern void digipot_i2c_set_current( int channel, float current ); + extern void digipot_i2c_init(); #endif extern void calculate_volumetric_multipliers(); +#endif //MARLIN_H diff --git a/Marlin/Sd2PinMap.h b/Marlin/Sd2PinMap.h index 0556bd301c..a94b9b3dc0 100644 --- a/Marlin/Sd2PinMap.h +++ b/Marlin/Sd2PinMap.h @@ -33,9 +33,7 @@ struct pin_map_t { uint8_t bit; }; //------------------------------------------------------------------------------ -#if defined(__AVR_ATmega1280__)\ -|| defined(__AVR_ATmega2560__) -// Mega +#if defined(__AVR_ATmega1280__) || defined(__AVR_ATmega2560__) // Mega // Two Wire (aka I2C) ports uint8_t const SDA_PIN = 20; // D1 @@ -43,6 +41,7 @@ uint8_t const SCL_PIN = 21; // D0 #undef MOSI_PIN #undef MISO_PIN +#undef SCK_PIN // SPI port uint8_t const SS_PIN = 53; // B0 uint8_t const MOSI_PIN = 51; // B2 diff --git a/Marlin/configurator/config/Configuration.h b/Marlin/configurator/config/Configuration.h index 04de471cd1..8fc198a226 100644 --- a/Marlin/configurator/config/Configuration.h +++ b/Marlin/configurator/config/Configuration.h @@ -756,6 +756,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of +#include "Conditionals_lcd.h" #include "Configuration_adv.h" #include "Conditionals.h" #include "SanityCheck.h" diff --git a/Marlin/configurator/config/Configuration_adv.h b/Marlin/configurator/config/Configuration_adv.h index 24243a48d9..6e4941a764 100644 --- a/Marlin/configurator/config/Configuration_adv.h +++ b/Marlin/configurator/config/Configuration_adv.h @@ -180,7 +180,7 @@ #define INVERT_Z_STEP_PIN false #define INVERT_E_STEP_PIN false -//default stepper release if idle. Set to 0 to deactivate. +// Default stepper release if idle. Set to 0 to deactivate. #define DEFAULT_STEPPER_DEACTIVE_TIME 60 #define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate @@ -188,14 +188,9 @@ // @section lcd -// Feedrates for manual moves along X, Y, Z, E from panel #ifdef ULTIPANEL - #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // set the speeds for manual moves (mm/min) -#endif - -//Comment to disable setting feedrate multiplier via encoder -#ifdef ULTIPANEL - #define ULTIPANEL_FEEDMULTIPLY + #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel + #define ULTIPANEL_FEEDMULTIPLY // Comment to disable setting feedrate multiplier via encoder #endif // @section extras @@ -368,9 +363,9 @@ const unsigned int dropsegments=5; //everything with less than this number of st #define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s) #endif -//adds support for experimental filament exchange support M600; requires display +// Add support for experimental filament exchange support M600; requires display #ifdef ULTIPANEL - #define FILAMENTCHANGEENABLE + //#define FILAMENTCHANGEENABLE #ifdef FILAMENTCHANGEENABLE #define FILAMENTCHANGE_XPOS 3 #define FILAMENTCHANGE_YPOS 3 diff --git a/Marlin/example_configurations/Felix/Configuration.h b/Marlin/example_configurations/Felix/Configuration.h index 03a09c6dbd..ebd49f81b5 100644 --- a/Marlin/example_configurations/Felix/Configuration.h +++ b/Marlin/example_configurations/Felix/Configuration.h @@ -692,6 +692,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of +#include "Conditionals_lcd.h" #include "Configuration_adv.h" #include "Conditionals.h" #include "SanityCheck.h" diff --git a/Marlin/example_configurations/Felix/Configuration_DUAL.h b/Marlin/example_configurations/Felix/Configuration_DUAL.h index 37c797882f..5e990df03a 100644 --- a/Marlin/example_configurations/Felix/Configuration_DUAL.h +++ b/Marlin/example_configurations/Felix/Configuration_DUAL.h @@ -689,6 +689,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of //#define FILAMENT_LCD_DISPLAY +#include "Conditionals_lcd.h" #include "Configuration_adv.h" #include "Conditionals.h" #include "SanityCheck.h" diff --git a/Marlin/example_configurations/Felix/Configuration_adv.h b/Marlin/example_configurations/Felix/Configuration_adv.h index 076b71ab21..0e93dca49c 100644 --- a/Marlin/example_configurations/Felix/Configuration_adv.h +++ b/Marlin/example_configurations/Felix/Configuration_adv.h @@ -163,20 +163,15 @@ #define INVERT_Z_STEP_PIN false #define INVERT_E_STEP_PIN false -//default stepper release if idle. Set to 0 to deactivate. +// Default stepper release if idle. Set to 0 to deactivate. #define DEFAULT_STEPPER_DEACTIVE_TIME 60 #define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate #define DEFAULT_MINTRAVELFEEDRATE 0.0 -// Feedrates for manual moves along X, Y, Z, E from panel #ifdef ULTIPANEL -#define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // set the speeds for manual moves (mm/min) -#endif - -//Comment to disable setting feedrate multiplier via encoder -#ifdef ULTIPANEL - #define ULTIPANEL_FEEDMULTIPLY + #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel + #define ULTIPANEL_FEEDMULTIPLY // Comment to disable setting feedrate multiplier via encoder #endif // minimum time in microseconds that a movement needs to take if the buffer is emptied. @@ -351,9 +346,9 @@ const unsigned int dropsegments=5; //everything with less than this number of st #define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s) #endif -//adds support for experimental filament exchange support M600; requires display +// Add support for experimental filament exchange support M600; requires display #ifdef ULTIPANEL - #define FILAMENTCHANGEENABLE + //#define FILAMENTCHANGEENABLE #ifdef FILAMENTCHANGEENABLE #define FILAMENTCHANGE_XPOS 3 #define FILAMENTCHANGE_YPOS 3 diff --git a/Marlin/example_configurations/Hephestos/Configuration.h b/Marlin/example_configurations/Hephestos/Configuration.h index 481ece7bb9..2220f7511a 100644 --- a/Marlin/example_configurations/Hephestos/Configuration.h +++ b/Marlin/example_configurations/Hephestos/Configuration.h @@ -720,6 +720,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of +#include "Conditionals_lcd.h" #include "Configuration_adv.h" #include "Conditionals.h" #include "SanityCheck.h" diff --git a/Marlin/example_configurations/Hephestos/Configuration_adv.h b/Marlin/example_configurations/Hephestos/Configuration_adv.h index 713a786be8..53819e677c 100644 --- a/Marlin/example_configurations/Hephestos/Configuration_adv.h +++ b/Marlin/example_configurations/Hephestos/Configuration_adv.h @@ -167,20 +167,15 @@ #define INVERT_Z_STEP_PIN false #define INVERT_E_STEP_PIN false -//default stepper release if idle. Set to 0 to deactivate. +// Default stepper release if idle. Set to 0 to deactivate. #define DEFAULT_STEPPER_DEACTIVE_TIME 60 #define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate #define DEFAULT_MINTRAVELFEEDRATE 0.0 -// Feedrates for manual moves along X, Y, Z, E from panel #ifdef ULTIPANEL -#define MANUAL_FEEDRATE {120*60, 120*60, 18*60, 60} // set the speeds for manual moves (mm/min) -#endif - -//Comment to disable setting feedrate multiplier via encoder -#ifdef ULTIPANEL - #define ULTIPANEL_FEEDMULTIPLY + #define MANUAL_FEEDRATE {120*60, 120*60, 18*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel + #define ULTIPANEL_FEEDMULTIPLY // Comment to disable setting feedrate multiplier via encoder #endif // minimum time in microseconds that a movement needs to take if the buffer is emptied. @@ -335,9 +330,9 @@ const unsigned int dropsegments=5; //everything with less than this number of st #define RETRACT_RECOVER_FEEDRATE 8*60 //default feedrate for recovering from retraction (mm/s) #endif -//adds support for experimental filament exchange support M600; requires display +// Add support for experimental filament exchange support M600; requires display #ifdef ULTIPANEL - #define FILAMENTCHANGEENABLE + //#define FILAMENTCHANGEENABLE #ifdef FILAMENTCHANGEENABLE #define FILAMENTCHANGE_XPOS 3 #define FILAMENTCHANGE_YPOS 3 diff --git a/Marlin/example_configurations/K8200/Configuration.h b/Marlin/example_configurations/K8200/Configuration.h index f3e063e34f..9400e4e49c 100644 --- a/Marlin/example_configurations/K8200/Configuration.h +++ b/Marlin/example_configurations/K8200/Configuration.h @@ -724,6 +724,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of +#include "Conditionals_lcd.h" #include "Configuration_adv.h" #include "Conditionals.h" #include "SanityCheck.h" diff --git a/Marlin/example_configurations/K8200/Configuration_adv.h b/Marlin/example_configurations/K8200/Configuration_adv.h index 8a8544d8f3..141f396936 100644 --- a/Marlin/example_configurations/K8200/Configuration_adv.h +++ b/Marlin/example_configurations/K8200/Configuration_adv.h @@ -163,20 +163,15 @@ #define INVERT_Z_STEP_PIN false #define INVERT_E_STEP_PIN false -//default stepper release if idle. Set to 0 to deactivate. +// Default stepper release if idle. Set to 0 to deactivate. #define DEFAULT_STEPPER_DEACTIVE_TIME 60 #define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate #define DEFAULT_MINTRAVELFEEDRATE 0.0 -// Feedrates for manual moves along X, Y, Z, E from panel #ifdef ULTIPANEL - #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // set the speeds for manual moves (mm/min) -#endif - -//Comment to disable setting feedrate multiplier via encoder -#ifdef ULTIPANEL - #define ULTIPANEL_FEEDMULTIPLY + #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel + #define ULTIPANEL_FEEDMULTIPLY // Comment to disable setting feedrate multiplier via encoder #endif // minimum time in microseconds that a movement needs to take if the buffer is emptied. @@ -331,9 +326,9 @@ const unsigned int dropsegments=5; //everything with less than this number of st #define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s) #endif -//adds support for experimental filament exchange support M600; requires display +// Add support for experimental filament exchange support M600; requires display #ifdef ULTIPANEL - #define FILAMENTCHANGEENABLE + //#define FILAMENTCHANGEENABLE #ifdef FILAMENTCHANGEENABLE #define FILAMENTCHANGE_XPOS 3 #define FILAMENTCHANGE_YPOS 3 diff --git a/Marlin/example_configurations/SCARA/Configuration.h b/Marlin/example_configurations/SCARA/Configuration.h index 5bf60e4fb9..7aafbf61d0 100644 --- a/Marlin/example_configurations/SCARA/Configuration.h +++ b/Marlin/example_configurations/SCARA/Configuration.h @@ -750,6 +750,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of +#include "Conditionals_lcd.h" #include "Configuration_adv.h" #include "Conditionals.h" #include "SanityCheck.h" diff --git a/Marlin/example_configurations/SCARA/Configuration_adv.h b/Marlin/example_configurations/SCARA/Configuration_adv.h index dfeb082db6..391c8058f6 100644 --- a/Marlin/example_configurations/SCARA/Configuration_adv.h +++ b/Marlin/example_configurations/SCARA/Configuration_adv.h @@ -165,20 +165,15 @@ #define INVERT_Z_STEP_PIN false #define INVERT_E_STEP_PIN false -//default stepper release if idle. Set to 0 to deactivate. +// Default stepper release if idle. Set to 0 to deactivate. #define DEFAULT_STEPPER_DEACTIVE_TIME 240 #define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate #define DEFAULT_MINTRAVELFEEDRATE 0.0 -// Feedrates for manual moves along X, Y, Z, E from panel #ifdef ULTIPANEL - #define MANUAL_FEEDRATE {50*60, 50*60, 10*60, 60} // set the speeds for manual moves (mm/min) -#endif - -//Comment to disable setting feedrate multiplier via encoder -#ifdef ULTIPANEL - #define ULTIPANEL_FEEDMULTIPLY + #define MANUAL_FEEDRATE {50*60, 50*60, 10*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel + #define ULTIPANEL_FEEDMULTIPLY // Comment to disable setting feedrate multiplier via encoder #endif // minimum time in microseconds that a movement needs to take if the buffer is emptied. @@ -335,9 +330,9 @@ const unsigned int dropsegments=5; //everything with less than this number of st #define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s) #endif -//adds support for experimental filament exchange support M600; requires display +// Add support for experimental filament exchange support M600; requires display #ifdef ULTIPANEL - #define FILAMENTCHANGEENABLE + //#define FILAMENTCHANGEENABLE #ifdef FILAMENTCHANGEENABLE #define FILAMENTCHANGE_XPOS 3 #define FILAMENTCHANGE_YPOS 3 diff --git a/Marlin/example_configurations/WITBOX/Configuration.h b/Marlin/example_configurations/WITBOX/Configuration.h index 3d907c250c..9654fa00d5 100644 --- a/Marlin/example_configurations/WITBOX/Configuration.h +++ b/Marlin/example_configurations/WITBOX/Configuration.h @@ -717,6 +717,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of +#include "Conditionals_lcd.h" #include "Configuration_adv.h" #include "Conditionals.h" #include "SanityCheck.h" diff --git a/Marlin/example_configurations/WITBOX/Configuration_adv.h b/Marlin/example_configurations/WITBOX/Configuration_adv.h index 4fca69e2ba..53819e677c 100644 --- a/Marlin/example_configurations/WITBOX/Configuration_adv.h +++ b/Marlin/example_configurations/WITBOX/Configuration_adv.h @@ -167,20 +167,15 @@ #define INVERT_Z_STEP_PIN false #define INVERT_E_STEP_PIN false -//default stepper release if idle. Set to 0 to deactivate. +// Default stepper release if idle. Set to 0 to deactivate. #define DEFAULT_STEPPER_DEACTIVE_TIME 60 #define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate #define DEFAULT_MINTRAVELFEEDRATE 0.0 -// Feedrates for manual moves along X, Y, Z, E from panel #ifdef ULTIPANEL - #define MANUAL_FEEDRATE {120*60, 120*60, 18*60, 60} // set the speeds for manual moves (mm/min) -#endif - -//Comment to disable setting feedrate multiplier via encoder -#ifdef ULTIPANEL - #define ULTIPANEL_FEEDMULTIPLY + #define MANUAL_FEEDRATE {120*60, 120*60, 18*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel + #define ULTIPANEL_FEEDMULTIPLY // Comment to disable setting feedrate multiplier via encoder #endif // minimum time in microseconds that a movement needs to take if the buffer is emptied. @@ -335,9 +330,9 @@ const unsigned int dropsegments=5; //everything with less than this number of st #define RETRACT_RECOVER_FEEDRATE 8*60 //default feedrate for recovering from retraction (mm/s) #endif -//adds support for experimental filament exchange support M600; requires display +// Add support for experimental filament exchange support M600; requires display #ifdef ULTIPANEL - #define FILAMENTCHANGEENABLE + //#define FILAMENTCHANGEENABLE #ifdef FILAMENTCHANGEENABLE #define FILAMENTCHANGE_XPOS 3 #define FILAMENTCHANGE_YPOS 3 diff --git a/Marlin/example_configurations/delta/generic/Configuration.h b/Marlin/example_configurations/delta/generic/Configuration.h index 16d51f32fe..e3c543b144 100644 --- a/Marlin/example_configurations/delta/generic/Configuration.h +++ b/Marlin/example_configurations/delta/generic/Configuration.h @@ -734,6 +734,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of +#include "Conditionals_lcd.h" #include "Configuration_adv.h" #include "Conditionals.h" #include "SanityCheck.h" diff --git a/Marlin/example_configurations/delta/generic/Configuration_adv.h b/Marlin/example_configurations/delta/generic/Configuration_adv.h index 2241f8c633..b2e1c86d4d 100644 --- a/Marlin/example_configurations/delta/generic/Configuration_adv.h +++ b/Marlin/example_configurations/delta/generic/Configuration_adv.h @@ -166,7 +166,7 @@ #define INVERT_Z_STEP_PIN false #define INVERT_E_STEP_PIN false -//default stepper release if idle. Set to 0 to deactivate. +// Default stepper release if idle. Set to 0 to deactivate. #define DEFAULT_STEPPER_DEACTIVE_TIME 60 #define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate @@ -174,7 +174,7 @@ // Feedrates for manual moves along X, Y, Z, E from panel #ifdef ULTIPANEL - #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // set the speeds for manual moves (mm/min) + #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel #endif // minimum time in microseconds that a movement needs to take if the buffer is emptied. @@ -330,9 +330,9 @@ const unsigned int dropsegments=5; //everything with less than this number of st #define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s) #endif -//adds support for experimental filament exchange support M600; requires display +// Add support for experimental filament exchange support M600; requires display #ifdef ULTIPANEL - #define FILAMENTCHANGEENABLE + //#define FILAMENTCHANGEENABLE #ifdef FILAMENTCHANGEENABLE #define FILAMENTCHANGE_XPOS 3 #define FILAMENTCHANGE_YPOS 3 diff --git a/Marlin/example_configurations/delta/kossel_mini/Configuration.h b/Marlin/example_configurations/delta/kossel_mini/Configuration.h index 97f1b28d76..5874d0475a 100644 --- a/Marlin/example_configurations/delta/kossel_mini/Configuration.h +++ b/Marlin/example_configurations/delta/kossel_mini/Configuration.h @@ -736,6 +736,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic o +#include "Conditionals_lcd.h" #include "Configuration_adv.h" #include "Conditionals.h" #include "SanityCheck.h" diff --git a/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h b/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h index 29ce19fa10..1ba4861ead 100644 --- a/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h +++ b/Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h @@ -166,7 +166,7 @@ #define INVERT_Z_STEP_PIN false #define INVERT_E_STEP_PIN false -//default stepper release if idle. Set to 0 to deactivate. +// Default stepper release if idle. Set to 0 to deactivate. #define DEFAULT_STEPPER_DEACTIVE_TIME 60 #define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate @@ -174,7 +174,7 @@ // Feedrates for manual moves along X, Y, Z, E from panel #ifdef ULTIPANEL - #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // set the speeds for manual moves (mm/min) + #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel #endif // minimum time in microseconds that a movement needs to take if the buffer is emptied. @@ -329,9 +329,9 @@ const unsigned int dropsegments=5; //everything with less than this number of st #define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s) #endif -//adds support for experimental filament exchange support M600; requires display +// Add support for experimental filament exchange support M600; requires display #ifdef ULTIPANEL - #define FILAMENTCHANGEENABLE + //#define FILAMENTCHANGEENABLE #ifdef FILAMENTCHANGEENABLE #define FILAMENTCHANGE_XPOS 3 #define FILAMENTCHANGE_YPOS 3 diff --git a/Marlin/example_configurations/makibox/Configuration.h b/Marlin/example_configurations/makibox/Configuration.h index ec85772ef0..83a5152d0f 100644 --- a/Marlin/example_configurations/makibox/Configuration.h +++ b/Marlin/example_configurations/makibox/Configuration.h @@ -715,6 +715,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of +#include "Conditionals_lcd.h" #include "Configuration_adv.h" #include "Conditionals.h" #include "SanityCheck.h" diff --git a/Marlin/example_configurations/makibox/Configuration_adv.h b/Marlin/example_configurations/makibox/Configuration_adv.h index 4575d4de20..eea93e43db 100644 --- a/Marlin/example_configurations/makibox/Configuration_adv.h +++ b/Marlin/example_configurations/makibox/Configuration_adv.h @@ -165,20 +165,15 @@ #define INVERT_Z_STEP_PIN false #define INVERT_E_STEP_PIN false -//default stepper release if idle. Set to 0 to deactivate. +// Default stepper release if idle. Set to 0 to deactivate. #define DEFAULT_STEPPER_DEACTIVE_TIME 60 #define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate #define DEFAULT_MINTRAVELFEEDRATE 0.0 -// Feedrates for manual moves along X, Y, Z, E from panel #ifdef ULTIPANEL - #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // set the speeds for manual moves (mm/min) -#endif - -//Comment to disable setting feedrate multiplier via encoder -#ifdef ULTIPANEL - #define ULTIPANEL_FEEDMULTIPLY + #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel + #define ULTIPANEL_FEEDMULTIPLY // Comment to disable setting feedrate multiplier via encoder #endif // minimum time in microseconds that a movement needs to take if the buffer is emptied. @@ -332,9 +327,9 @@ const unsigned int dropsegments=5; //everything with less than this number of st #define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s) #endif -//adds support for experimental filament exchange support M600; requires display +// Add support for experimental filament exchange support M600; requires display #ifdef ULTIPANEL - #define FILAMENTCHANGEENABLE + //#define FILAMENTCHANGEENABLE #ifdef FILAMENTCHANGEENABLE #define FILAMENTCHANGE_XPOS 3 #define FILAMENTCHANGE_YPOS 3 diff --git a/Marlin/example_configurations/tvrrug/Round2/Configuration.h b/Marlin/example_configurations/tvrrug/Round2/Configuration.h index 9aa6616458..09944999cc 100644 --- a/Marlin/example_configurations/tvrrug/Round2/Configuration.h +++ b/Marlin/example_configurations/tvrrug/Round2/Configuration.h @@ -722,6 +722,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of +#include "Conditionals_lcd.h" #include "Configuration_adv.h" #include "Conditionals.h" #include "SanityCheck.h" diff --git a/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h b/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h index c08102c972..7fdc38b83c 100644 --- a/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h +++ b/Marlin/example_configurations/tvrrug/Round2/Configuration_adv.h @@ -167,20 +167,15 @@ #define INVERT_Z_STEP_PIN false #define INVERT_E_STEP_PIN false -//default stepper release if idle. Set to 0 to deactivate. +// Default stepper release if idle. Set to 0 to deactivate. #define DEFAULT_STEPPER_DEACTIVE_TIME 60 #define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate #define DEFAULT_MINTRAVELFEEDRATE 0.0 -// Feedrates for manual moves along X, Y, Z, E from panel #ifdef ULTIPANEL - #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // set the speeds for manual moves (mm/min) -#endif - -// Comment to disable setting feedrate multiplier via encoder -#ifdef ULTIPANEL - #define ULTIPANEL_FEEDMULTIPLY + #define MANUAL_FEEDRATE {50*60, 50*60, 4*60, 60} // Feedrates for manual moves along X, Y, Z, E from panel + #define ULTIPANEL_FEEDMULTIPLY // Comment to disable setting feedrate multiplier via encoder #endif // minimum time in microseconds that a movement needs to take if the buffer is emptied. @@ -339,9 +334,9 @@ const unsigned int dropsegments=5; //everything with less than this number of st #define RETRACT_RECOVER_FEEDRATE 8 //default feedrate for recovering from retraction (mm/s) #endif -//adds support for experimental filament exchange support M600; requires display +// Add support for experimental filament exchange support M600; requires display #ifdef ULTIPANEL - #define FILAMENTCHANGEENABLE + //#define FILAMENTCHANGEENABLE #ifdef FILAMENTCHANGEENABLE #define FILAMENTCHANGE_XPOS 3 #define FILAMENTCHANGE_YPOS 3 diff --git a/Marlin/pins.h b/Marlin/pins.h index 38b1274f73..88c5cc78cb 100644 --- a/Marlin/pins.h +++ b/Marlin/pins.h @@ -5,8 +5,6 @@ #ifndef PINS_H #define PINS_H -#include "boards.h" - // Preset optional pins #define X_MS1_PIN -1 #define X_MS2_PIN -1 diff --git a/Marlin/ultralcd.cpp b/Marlin/ultralcd.cpp index c32478ced8..17712ce062 100644 --- a/Marlin/ultralcd.cpp +++ b/Marlin/ultralcd.cpp @@ -1,4 +1,3 @@ -#include "temperature.h" #include "ultralcd.h" #ifdef ULTRA_LCD #include "Marlin.h" diff --git a/Marlin/ultralcd.h b/Marlin/ultralcd.h index 9d89f514de..befe8fd1e2 100644 --- a/Marlin/ultralcd.h +++ b/Marlin/ultralcd.h @@ -14,10 +14,10 @@ void lcd_reset_alert_level(); bool lcd_detected(void); -#ifdef DOGLCD - extern int lcd_contrast; - void lcd_setcontrast(uint8_t value); -#endif + #ifdef DOGLCD + extern int lcd_contrast; + void lcd_setcontrast(uint8_t value); + #endif static unsigned char blink = 0; // Variable for visualization of fan rotation in GLCD @@ -28,27 +28,26 @@ #define LCD_TIMEOUT_TO_STATUS 15000 #ifdef ULTIPANEL - void lcd_buttons_update(); - extern volatile uint8_t buttons; //the last checked buttons in a bit array. - #ifdef REPRAPWORLD_KEYPAD - extern volatile uint8_t buttons_reprapworld_keypad; // to store the keypad shift register values - #endif + void lcd_buttons_update(); + extern volatile uint8_t buttons; //the last checked buttons in a bit array. + #ifdef REPRAPWORLD_KEYPAD + extern volatile uint8_t buttons_reprapworld_keypad; // to store the keypad shift register values + #endif #else - FORCE_INLINE void lcd_buttons_update() {} + FORCE_INLINE void lcd_buttons_update() {} #endif extern int plaPreheatHotendTemp; extern int plaPreheatHPBTemp; extern int plaPreheatFanSpeed; - extern int absPreheatHotendTemp; extern int absPreheatHPBTemp; extern int absPreheatFanSpeed; - + extern bool cancel_heatup; #ifdef FILAMENT_LCD_DISPLAY - extern unsigned long message_millis; + extern unsigned long message_millis; #endif void lcd_buzz(long duration,uint16_t freq);