General cleanup of Re-ARM pins

This commit is contained in:
Scott Lahteine 2018-11-21 19:00:39 -06:00
parent ee423dcdd0
commit b738972e69

View file

@ -98,13 +98,6 @@
#define E1_CS_PIN -1 #define E1_CS_PIN -1
#endif #endif
//#define E2_STEP_PIN P2_08 // (36)
//#define E2_DIR_PIN P2_13 // (34)
//#define E2_ENABLE_PIN P4_29 // (30)
//#ifndef E2_CS_PIN
// #define E2_CS_PIN -1
//#endif
// //
// Software SPI pins for TMC2130 stepper drivers // Software SPI pins for TMC2130 stepper drivers
// //
@ -205,23 +198,22 @@
#define PS_ON_PIN P2_12 // (12) #define PS_ON_PIN P2_12 // (12)
#if ENABLED(CASE_LIGHT_ENABLE) && !PIN_EXISTS(CASE_LIGHT) && !defined(SPINDLE_LASER_ENABLE_PIN) #if ENABLED(CASE_LIGHT_ENABLE) && !PIN_EXISTS(CASE_LIGHT) && !defined(SPINDLE_LASER_ENABLE_PIN)
#if !defined(NUM_SERVOS) || NUM_SERVOS < 4 // try to use servo connector #if !defined(NUM_SERVOS) || NUM_SERVOS < 4 // Try to use servo connector
#define CASE_LIGHT_PIN P1_18 // (4) MUST BE HARDWARE PWM #define CASE_LIGHT_PIN P1_18 // (4) MUST BE HARDWARE PWM
#endif #endif
#endif #endif
// //
// M3/M4/M5 - Spindle/Laser Control // M3/M4/M5 - Spindle/Laser Control
// Use servo pins, if available
// //
#if ENABLED(SPINDLE_LASER_ENABLE) && !PIN_EXISTS(SPINDLE_LASER_ENABLE) #if ENABLED(SPINDLE_LASER_ENABLE) && !PIN_EXISTS(SPINDLE_LASER_ENABLE)
#if !defined(NUM_SERVOS) || NUM_SERVOS == 1 // must use servo connector #if NUM_SERVOS > 1
#undef SERVO1 #error "SPINDLE_LASER_ENABLE requires 3 free servo pins."
#undef SERVO2
#undef SERVO3
#define SPINDLE_LASER_ENABLE_PIN P1_21 // (6) Pin should have a pullup/pulldown!
#define SPINDLE_LASER_PWM_PIN P1_18 // (4) MUST BE HARDWARE PWM
#define SPINDLE_DIR_PIN P1_19 // (5)
#endif #endif
#define SPINDLE_LASER_ENABLE_PIN SERVO1_PIN // (6) Pin should have a pullup/pulldown!
#define SPINDLE_LASER_PWM_PIN SERVO3_PIN // (4) MUST BE HARDWARE PWM
#define SPINDLE_DIR_PIN SERVO2_PIN // (5)
#endif #endif
// //
@ -237,6 +229,9 @@
* LCD / Controller * LCD / Controller
* *
* All controllers can use J3 and J5 on the Re-ARM board. Custom cabling will be required. * All controllers can use J3 and J5 on the Re-ARM board. Custom cabling will be required.
*
* - https://github.com/wolfmanjm/universal-panel-adapter
* - http://panucattdevices.freshdesk.com/support/solutions/articles/1000243195-lcd-display-installation
*/ */
/** /**
@ -252,8 +247,6 @@
* that the garbage/lines are erased immediately after the SD card accesses are completed. * that the garbage/lines are erased immediately after the SD card accesses are completed.
*/ */
#if ENABLED(ULTRA_LCD)
#if ENABLED(CR10_STOCKDISPLAY) #if ENABLED(CR10_STOCKDISPLAY)
// Re-Arm can support Creality stock display without SD card reader and single cable on EXP3. // Re-Arm can support Creality stock display without SD card reader and single cable on EXP3.
@ -271,7 +264,7 @@
#define LCD_PINS_ENABLE P0_18 // J3-10 & AUX-3 (SID, MOSI) #define LCD_PINS_ENABLE P0_18 // J3-10 & AUX-3 (SID, MOSI)
#define LCD_PINS_D4 P2_06 // J3-8 & AUX-3 (SCK, CLK) #define LCD_PINS_D4 P2_06 // J3-8 & AUX-3 (SCK, CLK)
#else #elif ENABLED(ULTRA_LCD)
#define BEEPER_PIN P1_30 // (37) not 5V tolerant #define BEEPER_PIN P1_30 // (37) not 5V tolerant
@ -279,7 +272,7 @@
#define BTN_EN2 P3_25 // (33) J3-4 & AUX-4 #define BTN_EN2 P3_25 // (33) J3-4 & AUX-4
#define BTN_ENC P2_11 // (35) J3-3 & AUX-4 #define BTN_ENC P2_11 // (35) J3-3 & AUX-4
#define SD_DETECT_PIN P1_31 // (49) not 5V tolerant J3-1 & AUX-3 #define SD_DETECT_PIN P1_31 // (49) J3-1 & AUX-3 (NOT 5V tolerant)
#define KILL_PIN P1_22 // (41) J5-4 & AUX-4 #define KILL_PIN P1_22 // (41) J5-4 & AUX-4
#define LCD_PINS_RS P0_16 // (16) J3-7 & AUX-4 #define LCD_PINS_RS P0_16 // (16) J3-7 & AUX-4
#define LCD_SDSS P0_16 // (16) J3-7 & AUX-4 #define LCD_SDSS P0_16 // (16) J3-7 & AUX-4
@ -288,7 +281,7 @@
#if ENABLED(REPRAPWORLD_KEYPAD) #if ENABLED(REPRAPWORLD_KEYPAD)
#define SHIFT_OUT P0_18 // (51) (MOSI) J3-10 & AUX-3 #define SHIFT_OUT P0_18 // (51) (MOSI) J3-10 & AUX-3
#define SHIFT_CLK P0_15 // (52) (SCK) J3-9 & AUX-3 #define SHIFT_CLK P0_15 // (52) (SCK) J3-9 & AUX-3
#define SHIFT_LD P1_31 // (49) not 5V tolerant J3-1 & AUX-3 #define SHIFT_LD P1_31 // (49) J3-1 & AUX-3 (NOT 5V tolerant)
#endif #endif
#else #else
//#define SHIFT_CLK P3_26 // (31) J3-2 & AUX-4 //#define SHIFT_CLK P3_26 // (31) J3-2 & AUX-4
@ -304,7 +297,7 @@
#define BTN_EN2 P3_25 // (33) J3-4 & AUX-4 #define BTN_EN2 P3_25 // (33) J3-4 & AUX-4
#define BTN_ENC P2_11 // (35) J3-3 & AUX-4 #define BTN_ENC P2_11 // (35) J3-3 & AUX-4
#define SD_DETECT_PIN P1_31 // (49) not 5V tolerant J3-1 & AUX-3 #define SD_DETECT_PIN P1_31 // (49) J3-1 & AUX-3 (NOT 5V tolerant)
#define KILL_PIN P1_22 // (41) J5-4 & AUX-4 #define KILL_PIN P1_22 // (41) J5-4 & AUX-4
#define DOGLCD_CS P0_16 // (16) #define DOGLCD_CS P0_16 // (16)
@ -330,7 +323,7 @@
//#define MISO_PIN P0_17 // (50) system defined J3-10 & AUX-3 //#define MISO_PIN P0_17 // (50) system defined J3-10 & AUX-3
//#define MOSI_PIN P0_18 // (51) system defined J3-10 & AUX-3 //#define MOSI_PIN P0_18 // (51) system defined J3-10 & AUX-3
//#define SCK_PIN P0_15 // (52) system defined J3-9 & AUX-3 //#define SCK_PIN P0_15 // (52) system defined J3-9 & AUX-3
//#define SS_PIN P1_23 // (53) system defined J3-5 & AUX-3 - sometimes called SDSS //#define SS_PIN P1_23 // (53) system defined J3-5 & AUX-3 (Sometimes called SDSS)
#if ENABLED(MINIPANEL) #if ENABLED(MINIPANEL)
// GLCD features // GLCD features
@ -341,8 +334,6 @@
//#define LCD_SCREEN_ROT_270 //#define LCD_SCREEN_ROT_270
#endif #endif
#endif
#endif // ULTRA_LCD #endif // ULTRA_LCD
// //
@ -383,6 +374,7 @@
#define SHARED_SD_CARD #define SHARED_SD_CARD
#undef SD_DETECT_PIN // there is also no detect pin for the onboard card #undef SD_DETECT_PIN // there is also no detect pin for the onboard card
#endif #endif
#define SCK_PIN P0_07 #define SCK_PIN P0_07
#define MISO_PIN P0_08 #define MISO_PIN P0_08
#define MOSI_PIN P0_09 #define MOSI_PIN P0_09
@ -406,6 +398,7 @@
* The following pins/signals use the direct method. All other pins use the * The following pins/signals use the direct method. All other pins use the
* the interrupt method. Note that SERVO2_PIN and RAMPS_D8_PIN use the * the interrupt method. Note that SERVO2_PIN and RAMPS_D8_PIN use the
* interrupt method. * interrupt method.
*
* P1_20 (11) SERVO0_PIN * P1_20 (11) SERVO0_PIN
* P1_21 ( 6) SERVO1_PIN J5-1 * P1_21 ( 6) SERVO1_PIN J5-1
* P0_18 ( 4) SERVO3_PIN 5V output * P0_18 ( 4) SERVO3_PIN 5V output
@ -418,31 +411,14 @@
/** /**
* Special pins * Special pins
* P1_30 (37) - not 5V tolerant * P1_30 (37) (NOT 5V tolerant)
* P1_31 (49) - not 5V tolerant * P1_31 (49) (NOT 5V tolerant)
* P0_27 (57) - open collector * P0_27 (57) (Open collector)
* P0_28 (58) - open collector * P0_28 (58) (Open collector)
*
*/ */
/** /**
* The following mega2560 pins are NOT available in a Re-ARM system * The following mega2560 pins are NOT available in a Re-ARM system:
* 7 *
* 17 * 7, 17, 22, 23, 25, 27, 29, 32, 39, 40, 42, 43, 44, 45, 47, 64, 65, 66
* 22
* 23
* 25
* 27
* 29
* 32
* 39
* 40
* 42
* 43
* 44
* 45
* 47
* 64
* 65
* 66
*/ */