Support for Extrudrboard in Printrboard Rev.F
This commit is contained in:
Scott Lahteine
parent
1b6c25a5e6
commit
b7feb53e8a
|
|
@ -661,7 +661,7 @@ void setup() {
|
|||
Max7219_init();
|
||||
#endif
|
||||
|
||||
#ifdef DISABLE_JTAG
|
||||
#if ENABLED(DISABLE_JTAG)
|
||||
// Disable JTAG on AT90USB chips to free up pins for IO
|
||||
MCUCR = 0x80;
|
||||
MCUCR = 0x80;
|
||||
|
|
|
|||
|
|
@ -70,7 +70,7 @@
|
|||
#define LARGE_FLASH true
|
||||
|
||||
// Disable JTAG pins so they can be used for the Extrudrboard
|
||||
#define DISABLE_JTAG true
|
||||
#define DISABLE_JTAG
|
||||
|
||||
//
|
||||
// Limit Switches
|
||||
|
|
|
|||
|
|
@ -30,8 +30,8 @@
|
|||
* There are two Arduino IDE extensions that are compatible with this board
|
||||
* and with the mainstream Marlin software.
|
||||
*
|
||||
* Teensyduino - http://www.pjrc.com/teensy/teensyduino.html
|
||||
* Installation instructions are at the above URL.
|
||||
* Teensyduino - https://www.pjrc.com/teensy/teensyduino.html
|
||||
* Installation - https://www.pjrc.com/teensy/td_download.html
|
||||
*
|
||||
* Select Teensy++ 2.0 in Arduino IDE from the 'Tools -> Boards' menu
|
||||
*
|
||||
|
|
@ -66,9 +66,36 @@
|
|||
#error "Oops! Make sure you have 'Teensy++ 2.0' or 'Printrboard' selected from the 'Tools -> Boards' menu."
|
||||
#endif
|
||||
|
||||
#ifndef USBCON
|
||||
#error "USBCON should be defined by the platform for this board."
|
||||
#endif
|
||||
|
||||
#define BOARD_NAME "Printrboard Rev F"
|
||||
#define LARGE_FLASH true
|
||||
|
||||
// Disable JTAG pins so EXP1 pins work correctly
|
||||
// (Its pins are used for the Extrudrboard and filament sensor, for example).
|
||||
#define DISABLE_JTAG
|
||||
|
||||
/**
|
||||
* Note that REV F6 of the Printrboard stole the A HOTEND pin and
|
||||
* reassigned it to a second fan for the extruder heater. It's
|
||||
* recommended that you swap the A and B outputs on the Extrudrboard
|
||||
* so EXTRUDERS=2 will still work on F6, using B for E1/HEATER_1/TEMP_1.
|
||||
* See https://printrbot.zendesk.com/hc/en-us/articles/115003072346
|
||||
*
|
||||
* If you have REV F6 you probably also want to set E0_AUTO_FAN_PIN
|
||||
* to PRINTRBOARD_F6_HEATER_FAN_PIN
|
||||
*
|
||||
* Define NO_EXTRUDRBOARD if you don't have an EXTRUDRBOARD and wish to
|
||||
* reassign different functions to EXP1.
|
||||
*
|
||||
* Define NO_EXTRUDRBOARD_OUTPUT_SWAP if you have a REV F5 or lower and
|
||||
* want to use EXTRUDRBOARD A for E1 and EXTRUDRBOARD B for E2.
|
||||
*/
|
||||
//#define NO_EXTRUDRBOARD
|
||||
//#define NO_EXTRUDRBOARD_OUTPUT_SWAP
|
||||
|
||||
//
|
||||
// Limit Switches
|
||||
//
|
||||
|
|
@ -95,6 +122,26 @@
|
|||
#define E0_DIR_PIN 35 // A7
|
||||
#define E0_ENABLE_PIN 13 // C3
|
||||
|
||||
#if DISABLED(NO_EXTRUDRBOARD)
|
||||
#if DISABLED(NO_EXTRUDRBOARD_OUTPUT_SWAP)
|
||||
#define E1_STEP_PIN 25 // B5
|
||||
#define E1_DIR_PIN 37 // E5
|
||||
#define E1_ENABLE_PIN 42 // F4
|
||||
|
||||
#define E2_STEP_PIN 2 // D2
|
||||
#define E2_DIR_PIN 3 // D3
|
||||
#define E2_ENABLE_PIN 43 // F5
|
||||
#else
|
||||
#define E1_STEP_PIN 2 // D2
|
||||
#define E1_DIR_PIN 3 // D3
|
||||
#define E1_ENABLE_PIN 43 // F5
|
||||
|
||||
#define E2_STEP_PIN 25 // B5
|
||||
#define E2_DIR_PIN 37 // E5
|
||||
#define E2_ENABLE_PIN 42 // F4
|
||||
#endif
|
||||
#endif // NO_EXTRUDRBOARD
|
||||
|
||||
// Enable control of stepper motor currents with the I2C based MCP4728 DAC used on Printrboard REVF
|
||||
#define DAC_STEPPER_CURRENT
|
||||
|
||||
|
|
@ -119,14 +166,32 @@
|
|||
#define TEMP_0_PIN 1 // Analog Input (Extruder)
|
||||
#define TEMP_BED_PIN 0 // Analog Input (Bed)
|
||||
|
||||
#if DISABLED(NO_EXTRUDRBOARD)
|
||||
#if DISABLED(NO_EXTRUDRBOARD_OUTPUT_SWAP)
|
||||
#define TEMP_1_PIN 2 // Analog Input (Extrudrboard A THERM)
|
||||
#define TEMP_2_PIN 3 // Analog Input (Extrudrboard B THERM)
|
||||
#else
|
||||
#define TEMP_1_PIN 3 // Analog Input (Extrudrboard B THERM)
|
||||
#define TEMP_2_PIN 2 // Analog Input (Extrudrboard A THERM)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
//
|
||||
// Heaters / Fans
|
||||
//
|
||||
#define HEATER_0_PIN 15 // C5 PWM3B - Extruder
|
||||
#define HEATER_1_PIN 44 // F6
|
||||
#define HEATER_2_PIN 45 // F7
|
||||
#define HEATER_BED_PIN 14 // C4 PWM3C
|
||||
|
||||
#if DISABLED(NO_EXTRUDRBOARD)
|
||||
#if DISABLED(NO_EXTRUDRBOARD_OUTPUT_SWAP)
|
||||
#define HEATER_1_PIN 44 // F6 - Extrudrboard A HOTEND
|
||||
#define HEATER_2_PIN 45 // F7 - Extrudrboard B HOTEND
|
||||
#else
|
||||
#define HEATER_1_PIN 45 // F7 - Extrudrboard B HOTEND
|
||||
#define HEATER_2_PIN 44 // F6 - Extrudrboard A HOTEND
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#define FAN_PIN 16 // C6 PWM3A
|
||||
|
||||
//
|
||||
|
|
@ -201,6 +266,14 @@
|
|||
#ifndef SDSS
|
||||
#define SDSS 20 // 10 B0
|
||||
#endif
|
||||
|
||||
/**
|
||||
* This is EXP1-2, which is also the TEMP_A_PIN for the Extrudrboard.
|
||||
* If using w/ Extrudrboard, cut off pin 2 on the Extrudrboard male
|
||||
* connector to ensure this is disconnected from the A THERM pullups.
|
||||
* You probably want to set EXTRUDERS=2 and swap the Extrudrboard outputs,
|
||||
* which will let you use Channel B on the Extrudrboard as E1.
|
||||
*/
|
||||
#ifndef FILWIDTH_PIN
|
||||
#define FILWIDTH_PIN 2 // Analog Input
|
||||
#define FILWIDTH_PIN 2 // Analog Input
|
||||
#endif
|
||||
|
|
|
|||
Loading…
Reference in a new issue