Tweak some config comments
This commit is contained in:
parent
fcf6d127fd
commit
bb561baf9e
|
@ -906,7 +906,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -597,7 +597,7 @@
|
|||
#define SD_DETECT_INVERTED
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
|
||||
|
||||
// Reverse SD sort to show "more recent" files first, according to the card's FAT.
|
||||
// Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
|
||||
|
|
|
@ -906,7 +906,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -597,7 +597,7 @@
|
|||
#define SD_DETECT_INVERTED
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
|
||||
|
||||
// Reverse SD sort to show "more recent" files first, according to the card's FAT.
|
||||
// Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
|
||||
|
|
|
@ -926,7 +926,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -597,7 +597,7 @@
|
|||
#define SD_DETECT_INVERTED
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
|
||||
|
||||
// Reverse SD sort to show "more recent" files first, according to the card's FAT.
|
||||
// Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
|
||||
|
|
|
@ -906,7 +906,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -906,7 +906,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -597,7 +597,7 @@
|
|||
#define SD_DETECT_INVERTED
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
|
||||
|
||||
// Reverse SD sort to show "more recent" files first, according to the card's FAT.
|
||||
// Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
|
||||
|
|
|
@ -906,7 +906,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -597,7 +597,7 @@
|
|||
#define SD_DETECT_INVERTED
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
|
||||
|
||||
// Reverse SD sort to show "more recent" files first, according to the card's FAT.
|
||||
// Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
|
||||
|
|
|
@ -986,7 +986,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -597,7 +597,7 @@
|
|||
//#define SD_DETECT_INVERTED
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
|
||||
|
||||
// Reverse SD sort to show "more recent" files first, according to the card's FAT.
|
||||
// Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
|
||||
|
|
|
@ -913,7 +913,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -597,7 +597,7 @@
|
|||
//#define SD_DETECT_INVERTED
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
|
||||
|
||||
// Reverse SD sort to show "more recent" files first, according to the card's FAT.
|
||||
// Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
|
||||
|
|
|
@ -906,7 +906,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -906,7 +906,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
#define Z_HOMING_HEIGHT 8 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
#define Z_HOMING_HEIGHT 8 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -597,7 +597,7 @@
|
|||
#define SD_DETECT_INVERTED
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
|
||||
|
||||
// Reverse SD sort to show "more recent" files first, according to the card's FAT.
|
||||
// Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
|
||||
|
|
|
@ -906,7 +906,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
#define Z_HOMING_HEIGHT 10 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
#define Z_HOMING_HEIGHT 10 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -597,7 +597,7 @@
|
|||
#define SD_DETECT_INVERTED
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
|
||||
|
||||
// Reverse SD sort to show "more recent" files first, according to the card's FAT.
|
||||
// Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
|
||||
|
|
|
@ -894,7 +894,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -597,7 +597,7 @@
|
|||
#define SD_DETECT_INVERTED
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
|
||||
|
||||
// Reverse SD sort to show "more recent" files first, according to the card's FAT.
|
||||
// Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
|
||||
|
|
|
@ -907,7 +907,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 3 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 3 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -605,7 +605,7 @@
|
|||
#define SD_DETECT_INVERTED
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE false // Disable steppers when SD Print is finished
|
||||
#define SD_FINISHED_RELEASECOMMAND "G27 P0" // You might want to keep the z enabled so your bed stays in place.
|
||||
#define SD_FINISHED_RELEASECOMMAND "G27 P0" // You might want to keep the Z enabled so your bed stays in place.
|
||||
|
||||
// Reverse SD sort to show "more recent" files first, according to the card's FAT.
|
||||
// Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
|
||||
|
|
|
@ -894,7 +894,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -597,7 +597,7 @@
|
|||
#define SD_DETECT_INVERTED
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
|
||||
|
||||
// Reverse SD sort to show "more recent" files first, according to the card's FAT.
|
||||
// Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
|
||||
|
|
|
@ -905,7 +905,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -597,7 +597,7 @@
|
|||
#define SD_DETECT_INVERTED
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
|
||||
|
||||
// Reverse SD sort to show "more recent" files first, according to the card's FAT.
|
||||
// Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
|
||||
|
|
|
@ -916,7 +916,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 5 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 5 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -597,7 +597,7 @@
|
|||
#define SD_DETECT_INVERTED
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
|
||||
|
||||
// Reverse SD sort to show "more recent" files first, according to the card's FAT.
|
||||
// Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
|
||||
|
|
|
@ -910,7 +910,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -597,7 +597,7 @@
|
|||
#define SD_DETECT_INVERTED
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
|
||||
|
||||
// Reverse SD sort to show "more recent" files first, according to the card's FAT.
|
||||
// Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
|
||||
|
|
|
@ -925,7 +925,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 5 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 5 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -597,7 +597,7 @@
|
|||
#define SD_DETECT_INVERTED
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
|
||||
|
||||
// Reverse SD sort to show "more recent" files first, according to the card's FAT.
|
||||
// Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
|
||||
|
|
|
@ -916,7 +916,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -597,7 +597,7 @@
|
|||
#define SD_DETECT_INVERTED
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
|
||||
|
||||
// Reverse SD sort to show "more recent" files first, according to the card's FAT.
|
||||
// Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
|
||||
|
|
|
@ -910,7 +910,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -597,7 +597,7 @@
|
|||
#define SD_DETECT_INVERTED
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
|
||||
|
||||
// Reverse SD sort to show "more recent" files first, according to the card's FAT.
|
||||
// Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
|
||||
|
|
|
@ -910,7 +910,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -597,7 +597,7 @@
|
|||
#define SD_DETECT_INVERTED
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
|
||||
|
||||
// Reverse SD sort to show "more recent" files first, according to the card's FAT.
|
||||
// Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
|
||||
|
|
|
@ -916,7 +916,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -597,7 +597,7 @@
|
|||
#define SD_DETECT_INVERTED
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
|
||||
|
||||
// Reverse SD sort to show "more recent" files first, according to the card's FAT.
|
||||
// Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
|
||||
|
|
|
@ -916,7 +916,7 @@
|
|||
|
||||
#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -597,7 +597,7 @@
|
|||
#define SD_DETECT_INVERTED
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
|
||||
|
||||
// Reverse SD sort to show "more recent" files first, according to the card's FAT.
|
||||
// Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
|
||||
|
|
|
@ -602,7 +602,7 @@
|
|||
//=============================================================================
|
||||
// @section motion
|
||||
|
||||
// default steps per unit for Felix 2.0/3.0: 0.00249mm x/y rounding error with 3mm pitch HTD belt and 14 tooth pulleys. 0 z error.
|
||||
// default steps per unit for Felix 2.0/3.0: 0.00249mm x/y rounding error with 3mm pitch HTD belt and 14 tooth pulleys. 0 Z error.
|
||||
/**
|
||||
* Default Settings
|
||||
*
|
||||
|
@ -888,7 +888,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -597,7 +597,7 @@
|
|||
#define SD_DETECT_INVERTED
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
|
||||
|
||||
// Reverse SD sort to show "more recent" files first, according to the card's FAT.
|
||||
// Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
|
||||
|
|
|
@ -602,7 +602,7 @@
|
|||
//=============================================================================
|
||||
// @section motion
|
||||
|
||||
// default steps per unit for Felix 2.0/3.0: 0.00249mm x/y rounding error with 3mm pitch HTD belt and 14 tooth pulleys. 0 z error.
|
||||
// default steps per unit for Felix 2.0/3.0: 0.00249mm x/y rounding error with 3mm pitch HTD belt and 14 tooth pulleys. 0 Z error.
|
||||
/**
|
||||
* Default Settings
|
||||
*
|
||||
|
@ -888,7 +888,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -912,7 +912,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
#define Z_HOMING_HEIGHT 2 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
#define Z_HOMING_HEIGHT 2 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -597,7 +597,7 @@
|
|||
#define SD_DETECT_INVERTED
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
|
||||
|
||||
// Reverse SD sort to show "more recent" files first, according to the card's FAT.
|
||||
// Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
|
||||
|
|
|
@ -1002,7 +1002,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -597,7 +597,7 @@
|
|||
#define SD_DETECT_INVERTED
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
|
||||
|
||||
// Reverse SD sort to show "more recent" files first, according to the card's FAT.
|
||||
// Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
|
||||
|
|
|
@ -944,7 +944,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
#define Z_HOMING_HEIGHT 8 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
#define Z_HOMING_HEIGHT 8 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -601,7 +601,7 @@
|
|||
#define SD_DETECT_INVERTED
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
|
||||
|
||||
// Reverse SD sort to show "more recent" files first, according to the card's FAT.
|
||||
// Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
|
||||
|
|
|
@ -927,7 +927,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
#define Z_HOMING_HEIGHT 8 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
#define Z_HOMING_HEIGHT 8 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -602,7 +602,7 @@
|
|||
#define SD_DETECT_INVERTED
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
|
||||
|
||||
// Reverse SD sort to show "more recent" files first, according to the card's FAT.
|
||||
// Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
|
||||
|
|
|
@ -921,7 +921,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -906,7 +906,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
#define Z_HOMING_HEIGHT 8 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
#define Z_HOMING_HEIGHT 8 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -922,7 +922,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -921,7 +921,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -906,7 +906,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -597,7 +597,7 @@
|
|||
#define SD_DETECT_INVERTED
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
|
||||
|
||||
// Reverse SD sort to show "more recent" files first, according to the card's FAT.
|
||||
// Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
|
||||
|
|
|
@ -906,7 +906,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -597,7 +597,7 @@
|
|||
#define SD_DETECT_INVERTED
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
|
||||
|
||||
// Reverse SD sort to show "more recent" files first, according to the card's FAT.
|
||||
// Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
|
||||
|
|
|
@ -910,7 +910,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -597,7 +597,7 @@
|
|||
#define SD_DETECT_INVERTED
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
|
||||
|
||||
// Reverse SD sort to show "more recent" files first, according to the card's FAT.
|
||||
// Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
|
||||
|
|
|
@ -918,7 +918,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -597,7 +597,7 @@
|
|||
#define SD_DETECT_INVERTED
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
|
||||
|
||||
// Reverse SD sort to show "more recent" files first, according to the card's FAT.
|
||||
// Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
|
||||
|
|
|
@ -926,7 +926,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -597,7 +597,7 @@
|
|||
#define SD_DETECT_INVERTED
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
|
||||
|
||||
// Reverse SD sort to show "more recent" files first, according to the card's FAT.
|
||||
// Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
|
||||
|
|
|
@ -930,7 +930,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -597,7 +597,7 @@
|
|||
#define SD_DETECT_INVERTED
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
|
||||
|
||||
// Reverse SD sort to show "more recent" files first, according to the card's FAT.
|
||||
// Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
|
||||
|
|
|
@ -905,7 +905,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -597,7 +597,7 @@
|
|||
#define SD_DETECT_INVERTED
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
|
||||
|
||||
// Reverse SD sort to show "more recent" files first, according to the card's FAT.
|
||||
// Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
|
||||
|
|
|
@ -910,7 +910,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -910,7 +910,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -597,7 +597,7 @@
|
|||
#define SD_DETECT_INVERTED
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
|
||||
|
||||
// Reverse SD sort to show "more recent" files first, according to the card's FAT.
|
||||
// Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
|
||||
|
|
|
@ -906,7 +906,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -598,7 +598,7 @@
|
|||
#define SD_DETECT_INVERTED
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
|
||||
|
||||
// Reverse SD sort to show "more recent" files first, according to the card's FAT.
|
||||
// Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
|
||||
|
|
|
@ -687,7 +687,7 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley
|
|||
* Override with M203
|
||||
* X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]]
|
||||
*/
|
||||
#define DEFAULT_MAX_Z_FEEDRATE 3.3 // older Huxley has problem with speeds > 3.3 mm/s on z axis
|
||||
#define DEFAULT_MAX_Z_FEEDRATE 3.3 // older Huxley has problem with speeds > 3.3 mm/s on Z axis
|
||||
#define DEFAULT_MAX_FEEDRATE { 200, 200, DEFAULT_MAX_Z_FEEDRATE, 25 }
|
||||
|
||||
/**
|
||||
|
@ -946,7 +946,7 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -906,7 +906,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -904,7 +904,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -597,7 +597,7 @@
|
|||
#define SD_DETECT_INVERTED
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
|
||||
|
||||
// Reverse SD sort to show "more recent" files first, according to the card's FAT.
|
||||
// Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
|
||||
|
|
|
@ -919,7 +919,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -597,7 +597,7 @@
|
|||
#define SD_DETECT_INVERTED
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
|
||||
|
||||
// Reverse SD sort to show "more recent" files first, according to the card's FAT.
|
||||
// Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
|
||||
|
|
|
@ -908,7 +908,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -906,7 +906,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -937,7 +937,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -597,7 +597,7 @@
|
|||
#define SD_DETECT_INVERTED
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
|
||||
|
||||
// Reverse SD sort to show "more recent" files first, according to the card's FAT.
|
||||
// Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
|
||||
|
|
|
@ -906,7 +906,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -597,7 +597,7 @@
|
|||
#define SD_DETECT_INVERTED
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
|
||||
|
||||
// Reverse SD sort to show "more recent" files first, according to the card's FAT.
|
||||
// Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
|
||||
|
|
|
@ -957,7 +957,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -597,7 +597,7 @@
|
|||
#define SD_DETECT_INVERTED
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
|
||||
|
||||
// Reverse SD sort to show "more recent" files first, according to the card's FAT.
|
||||
// Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
|
||||
|
|
|
@ -906,7 +906,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -906,7 +906,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -597,7 +597,7 @@
|
|||
#define SD_DETECT_INVERTED
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
|
||||
|
||||
// Reverse SD sort to show "more recent" files first, according to the card's FAT.
|
||||
// Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
|
||||
|
|
|
@ -906,7 +906,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 10 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 10 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -917,7 +917,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -906,7 +906,7 @@
|
|||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
|
@ -597,7 +597,7 @@
|
|||
#define SD_DETECT_INVERTED
|
||||
|
||||
#define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
||||
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
|
||||
|
||||
// Reverse SD sort to show "more recent" files first, according to the card's FAT.
|
||||
// Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
|
||||
|
|
|
@ -936,7 +936,7 @@
|
|||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
// K8200: it is usual to have clamps for the glass plate on the heatbed
|
||||
#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
|
|
Some files were not shown because too many files have changed in this diff Show more
Loading…
Reference in a new issue