FLSun Hispeedv1 Board update (#19959)
Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>
This commit is contained in:
Foxies
GitHub
parent
ecd8227de0
commit
c1920f31ca
|
|
@ -55,6 +55,7 @@
|
|||
#define MARLIN_EEPROM_SIZE EEPROM_PAGE_SIZE // 2KB
|
||||
#endif
|
||||
|
||||
//
|
||||
// SPI
|
||||
// Note: FLSun Hispeed (clone MKS_Robin_miniV2) board is using SPI2 interface.
|
||||
//
|
||||
|
|
@ -108,49 +109,26 @@
|
|||
#define E0_STEP_PIN PD6 // E0_STEP
|
||||
#define E0_DIR_PIN PD3 // E0_DIR
|
||||
|
||||
/**
|
||||
* FLSUN Hi-Speed has no hard-wired UART pins for TMC drivers.
|
||||
* Several wiring options are provided below, defaulting to
|
||||
* to the most compatible.
|
||||
*/
|
||||
|
||||
//
|
||||
// Drivers
|
||||
//
|
||||
#if HAS_TMC220x
|
||||
|
||||
#if ENABLED(HARDWARE_SERIAL) /* TMC2209 */
|
||||
#define X_SLAVE_ADDRESS 3 // | | :
|
||||
#define Y_SLAVE_ADDRESS 2 // : | :
|
||||
#define Z_SLAVE_ADDRESS 1 // | : :
|
||||
//#define E0_SLAVE_ADDRESS 0 // : : :
|
||||
|
||||
#define X_SERIAL_TX_PIN PA9 // TXD1
|
||||
#define X_SERIAL_RX_PIN PA9 // TXD1
|
||||
|
||||
#define Y_SERIAL_TX_PIN PA9 // TXD1
|
||||
#define Y_SERIAL_RX_PIN PA9 // TXD1
|
||||
|
||||
#define Z_SERIAL_TX_PIN PA9 // TXD1
|
||||
#define Z_SERIAL_RX_PIN PA9 // TXD1
|
||||
|
||||
#elif ENABLED(SOFTWARE_SERIAL) /* TMC220x */
|
||||
/**
|
||||
* TMC2208 stepper UART-configurable by PDN_UART pin
|
||||
* Software serial
|
||||
*/
|
||||
#define X_SLAVE_ADDRESS 0
|
||||
#define Y_SLAVE_ADDRESS 0
|
||||
#define Z_SLAVE_ADDRESS 0
|
||||
|
||||
// SoftwareSerial with one pin per driver
|
||||
// Compatible with TMC2208 and TMC2209 drivers
|
||||
#define X_SERIAL_TX_PIN PA10 // RXD1
|
||||
#define X_SERIAL_RX_PIN PA10 // RXD1
|
||||
|
||||
#define Y_SERIAL_TX_PIN PA9 // TXD1
|
||||
#define Y_SERIAL_RX_PIN PA9 // TXD1
|
||||
|
||||
#define Z_SERIAL_TX_PIN PC7 // IO1
|
||||
#define Z_SERIAL_RX_PIN PC7 // IO1
|
||||
|
||||
#endif
|
||||
// Reduce baud rate to improve software serial reliability
|
||||
#define TMC_BAUD_RATE 19200
|
||||
#else
|
||||
|
||||
// Motor current PWM pins
|
||||
#define MOTOR_CURRENT_PWM_XY_PIN PA6 // VREF2/3 CONTROL XY
|
||||
#define MOTOR_CURRENT_PWM_Z_PIN PA7 // VREF4 CONTROL Z
|
||||
|
|
@ -160,32 +138,32 @@
|
|||
#endif
|
||||
|
||||
/**
|
||||
* src: MKS Robin_Mini V2
|
||||
* MKS Robin_Wifi or another ESP8266 module
|
||||
*
|
||||
* __ESP(M1)__ -J1-
|
||||
* GND| 15 | | 08 |+3v3 (22)=>RXD1(PA10) //
|
||||
* | 16 | | 07 |MOSI (21)=>TXD1(PA9) // active low, probably OK to leave floating
|
||||
* IO2| 17 | | 06 |MISO (19)=>IO1(PC7) // Leave as unused (ESP3D software configures this with a pullup so OK to leave as floating)
|
||||
* IO0| 18 | | 05 |CLK (18)=>IO0(PA8) // must be high (ESP3D software configures this with a pullup so OK to leave as floating)
|
||||
* IO1| 19 | | 03 |EN (03)=>WIFI_EN() // Must be high for module to run
|
||||
* | nc | | nc | (01)=>WIFI_CTRL(PA5)
|
||||
* GND| 15 | | 08 |+3v3 (22) RXD1 (PA10)
|
||||
* | 16 | | 07 |MOSI (21) TXD1 (PA9) Active LOW, probably OK to leave floating
|
||||
* IO2| 17 | | 06 |MISO (19) IO1 (PC7) Leave as unused (ESP3D software configures this with a pullup so OK to leave as floating)
|
||||
* IO0| 18 | | 05 |CLK (18) IO0 (PA8) Must be HIGH (ESP3D software configures this with a pullup so OK to leave as floating)
|
||||
* IO1| 19 | | 03 |EN (03) WIFI_EN Must be HIGH for module to run
|
||||
* | nc | | nc | (01) WIFI_CTRL (PA5)
|
||||
* RX| 21 | | nc |
|
||||
* TX| 22 | | 01 |RST
|
||||
* ￣￣ AE￣￣
|
||||
*
|
||||
*/
|
||||
#ifdef ESP_WIFI
|
||||
#define WIFI_IO0_PIN PA8 // PC13 MKS ESP WIFI IO0 PIN
|
||||
#define WIFI_IO1_PIN PC7 // MKS ESP WIFI IO1 PIN
|
||||
#define WIFI_RESET_PIN PA5 // MKS ESP WIFI RESET PIN
|
||||
#endif
|
||||
// Module ESP-WIFI
|
||||
#define ESP_WIFI_MODULE_COM 2 // Must also set either SERIAL_PORT or SERIAL_PORT_2 to this
|
||||
#define ESP_WIFI_MODULE_BAUDRATE BAUDRATE // Must use same BAUDRATE as SERIAL_PORT & SERIAL_PORT_2
|
||||
#define ESP_WIFI_MODULE_RESET_PIN PA5 // WIFI CTRL/RST
|
||||
#define ESP_WIFI_MODULE_ENABLE_PIN -1
|
||||
#define ESP_WIFI_MODULE_TXD_PIN PA9 // MKS or ESP WIFI RX PIN
|
||||
#define ESP_WIFI_MODULE_RXD_PIN PA10 // MKS or ESP WIFI TX PIN
|
||||
#endif
|
||||
|
||||
//
|
||||
// EXTRUDER
|
||||
//
|
||||
#if AXIS_DRIVER_TYPE(E0,TMC2208)||AXIS_DRIVER_TYPE(E0,TMC2209)
|
||||
#define E0_SLAVE_ADDRESS 0
|
||||
|
||||
#if AXIS_DRIVER_TYPE_E0(TMC2208) || AXIS_DRIVER_TYPE_E0(TMC2209)
|
||||
#define E0_SERIAL_TX_PIN PA8 // IO0
|
||||
#define E0_SERIAL_RX_PIN PA8 // IO0
|
||||
#define TMC_BAUD_RATE 19200
|
||||
|
|
@ -211,7 +189,6 @@
|
|||
#define HEATER_BED_PIN PA0 // HEATER_BED-WKUP
|
||||
|
||||
#define FAN_PIN PB1 // E_FAN
|
||||
//#define CONTROLLER_FAN_PIN PD6 // BOARD FAN
|
||||
|
||||
//
|
||||
// Misc. Functions
|
||||
|
|
@ -221,12 +198,24 @@
|
|||
#define POWER_LOSS_PIN PA2 // PW_DET (UPS) MKSPWC
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Connector J2
|
||||
* -------
|
||||
* DIO O|1 2|O 3v3
|
||||
* CSK O|3 5|O GND
|
||||
* RST O|5 6|O GND
|
||||
* -------
|
||||
*/
|
||||
//#define SW_DIO PA13
|
||||
//#define SW_CLK PA14
|
||||
//#define SW_RST NRST // (14)
|
||||
|
||||
//
|
||||
// Power Supply Control
|
||||
//
|
||||
#if ENABLED(PSU_CONTROL)
|
||||
#define KILL_PIN PA2 // PW_DET
|
||||
#define KILL_PIN_INVERTING true //
|
||||
#define KILL_PIN_INVERTING true
|
||||
//#define PS_ON_PIN PA3 // PW_CN /PW_OFF
|
||||
#endif
|
||||
|
||||
|
|
@ -240,28 +229,33 @@
|
|||
//#define LED_PIN PB2 // BOOT1
|
||||
|
||||
#if ENABLED(NEOPIXEL_LED)
|
||||
#define LED_PWM PA8
|
||||
#define LED_PWM PC7 // IO1
|
||||
#ifndef NEOPIXEL_PIN
|
||||
#define NEOPIXEL_PIN LED_PWM // USED WIFI IO0/IO1/TX/RX PIN
|
||||
#define NEOPIXEL_PIN LED_PWM // USED WIFI IO0/IO1 PIN
|
||||
#endif
|
||||
#endif
|
||||
|
||||
//Others test.
|
||||
//#define SERVO0_PIN PA5 // WIFI CRTL
|
||||
//#define GPIO_CLEAR PA8 // IO0
|
||||
//#define GPIO_SET PA5
|
||||
|
||||
//
|
||||
// SD Card
|
||||
//
|
||||
#ifndef SDCARD_CONNECTION
|
||||
#define SDCARD_CONNECTION ONBOARD
|
||||
#endif
|
||||
|
||||
// Use the on-board card socket labeled SD_Extender
|
||||
#if SD_CONNECTION_IS(CUSTOM_CABLE)
|
||||
#define SCK_PIN PC12
|
||||
#define MISO_PIN PC8
|
||||
#define MOSI_PIN PD2
|
||||
#define SS_PIN -1
|
||||
#define SD_DETECT_PIN PD12 // SD_CD (if -1 no detection)
|
||||
#else
|
||||
#define SDIO_SUPPORT
|
||||
#define SDIO_CLOCK 4500000 // 4.5 MHz /* 18 MHz (18000000) or 4.5MHz (450000) */
|
||||
//#define SDIO_CLOCK 18000000 // 18 MHz (18000000)
|
||||
#if ENABLED(SDIO_SUPPORT)
|
||||
#define SCK_PIN PB13 // SPI2
|
||||
#define MISO_PIN PB14 // SPI2
|
||||
#define MOSI_PIN PB15 // SPI2
|
||||
#define SD_DETECT_PIN PD12 // SD_CD
|
||||
#define SDIO_CLOCK 4500000 // 4.5 MHz
|
||||
#define SDIO_READ_RETRIES 16
|
||||
#define ONBOARD_SPI_DEVICE 1 // SPI1
|
||||
#define ONBOARD_SD_CS_PIN PC11
|
||||
#define SD_DETECT_PIN -1 // SD_CD (-1 active refresh)
|
||||
#endif
|
||||
|
||||
//
|
||||
|
|
@ -271,6 +265,10 @@
|
|||
#define BEEPER_PIN PC5
|
||||
#endif
|
||||
|
||||
#if ENABLED(SPEAKER) && BEEPER_PIN == PC5
|
||||
#error "FLSun HiSpeed default BEEPER_PIN is not a SPEAKER."
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Note: MKS Robin TFT screens use various TFT controllers
|
||||
* Supported screens are based on the ILI9341, ST7789V and ILI9328 (320x240)
|
||||
|
|
@ -284,26 +282,7 @@
|
|||
* because Marlin uses the reset as a failsafe to revive a glitchy LCD.
|
||||
*/
|
||||
|
||||
// MKS Robin TFT v2.0 with ILI9341
|
||||
// Read display identification information (0xD3 on ILI9341)
|
||||
//#define TOUCH_CALIBRATION_X 12013
|
||||
//#define TOUCH_CALIBRATION_Y -8711
|
||||
//#define TOUCH_OFFSET_X -32
|
||||
//#define TOUCH_OFFSET_Y 256
|
||||
|
||||
// MKS Robin TFT v1.1 with ILI9328
|
||||
//#define TOUCH_CALIBRATION_X -11792
|
||||
//#define TOUCH_CALIBRATION_Y 8947
|
||||
//#define TOUCH_OFFSET_X 342
|
||||
//#define TOUCH_OFFSET_Y -19
|
||||
|
||||
// MKS Robin TFT v1.1 with R61505
|
||||
//#define TOUCH_CALIBRATION_X 12489
|
||||
//#define TOUCH_CALIBRATION_Y 9210
|
||||
//#define TOUCH_OFFSET_X -52
|
||||
//#define TOUCH_OFFSET_Y -17
|
||||
|
||||
// QQS-Pro uses MKS Robin TFT v2.0
|
||||
// QQS-Pro uses MKS Robin TFT v2.0 320x240
|
||||
|
||||
// Shared FSMC Configs
|
||||
#if HAS_FSMC_TFT
|
||||
|
|
@ -320,8 +299,13 @@
|
|||
#define FSMC_DMA_DEV DMA2
|
||||
#define FSMC_DMA_CHANNEL DMA_CH5
|
||||
|
||||
#define TOUCH_BUTTONS_HW_SPI
|
||||
#define TOUCH_BUTTONS_HW_SPI_DEVICE 2
|
||||
#define TFT_BUFFER_SIZE 14400
|
||||
#if ENABLED(TFT_CLASSIC_UI)
|
||||
#define TFT_MARLINBG_COLOR 0x3186 // White
|
||||
#define TFT_MARLINUI_COLOR 0xC7B6 // green
|
||||
#define TFT_BTARROWS_COLOR 0xDEE6 // Yellow
|
||||
#define TFT_BTOKMENU_COLOR 0x145F // Cyan
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#if NEED_TOUCH_PINS
|
||||
|
|
|
|||
Loading…
Reference in a new issue