Merge pull request #411 from STB3/Marlin_w_STB_Board_support

Add STB board support to Marlin (next step towards graphic LCD implementation)

Marlin/Configuration.h

@@ -34,6 +34,7 @@
 // 6  = Sanguinololu < 1.2
 // 62 = Sanguinololu 1.2 and above
 // 63 = Melzi
+// 64 = STB V1.1
 // 7  = Ultimaker
 // 71 = Ultimaker (Older electronics. Pre 1.5.4. This is rare)
 // 8  = Teensylu
@@ -314,6 +315,7 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
 
 //LCD and SD support
 //#define ULTRA_LCD  //general lcd support, also 16x2
+//#define DOGLCD	// Support for SPI LCD 128x64 (Controller ST7565R graphic Display Family)
 //#define SDSUPPORT // Enable SD Card Support in Hardware Console
 
 //#define ULTIMAKERCONTROLLER //as available from the ultimaker online store.
@@ -347,15 +349,24 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
 //  #define NEWPANEL  //enable this if you have a click-encoder panel
   #define SDSUPPORT
   #define ULTRA_LCD
+	#ifdef DOGLCD	// Change number of lines to match the DOG graphic display
+		#define LCD_WIDTH 20
+		#define LCD_HEIGHT 5
+	#else
 		#define LCD_WIDTH 20
 		#define LCD_HEIGHT 4
-  
+	#endif
 #else //no panel but just lcd 
   #ifdef ULTRA_LCD
+	#ifdef DOGLCD	// Change number of lines to match the 128x64 graphics display
+		#define LCD_WIDTH 20
+		#define LCD_HEIGHT 5
+	#else
 		#define LCD_WIDTH 16
 		#define LCD_HEIGHT 2
 	#endif    
   #endif
+#endif
 
 // Increase the FAN pwm frequency. Removes the PWM noise but increases heating in the FET/Arduino
 //#define FAST_PWM_FAN

Marlin/language.h

@@ -3,8 +3,8 @@
 
 // NOTE: IF YOU CHANGE THIS FILE / MERGE THIS FILE WITH CHANGES
 //
-//   ==> ALWAYS TRY TO COMPILE MARLIN WITH/WITHOUT "ULTIPANEL" / "ULTRALCD" / "SDSUPPORT" #define IN "Configuration.h" 
-//   ==> ALSO TRY ALL AVAILABLE "LANGUAGE_CHOICE" OPTIONS
+//   ==> ALWAYS TRY TO COMPILE MARLIN WITH/WITHOUT "ULTIPANEL" / "ULTRALCD" / "SDSUPPORT" #define IN "Configuration.h" 
+//   ==> ALSO TRY ALL AVAILABLE "LANGUAGE_CHOICE" OPTIONS
 
 // Languages
 // 1  English
@@ -1462,3 +1462,4 @@
 
 #endif
 #endif // ifndef LANGUAGE_H
+</pre></body></html>

Marlin/pins.h

@@ -644,10 +644,13 @@
 * Sanguinololu pin assignment
 *
 ****************************************************************************************/
+#if MOTHERBOARD == 64
+#define STB
+#endif
 #if MOTHERBOARD == 63
 #define MELZI
 #endif
-#if MOTHERBOARD == 62 || MOTHERBOARD == 63
+#if MOTHERBOARD == 62 || MOTHERBOARD == 63 || MOTHERBOARD == 64
 #undef MOTHERBOARD
 #define MOTHERBOARD 6
 #define SANGUINOLOLU_V_1_2 
@@ -687,6 +690,10 @@
 #define FAN_PIN            4
 #endif
 
+#ifdef STB
+#define FAN_PIN            4
+#endif
+
 #define PS_ON_PIN          -1
 #define KILL_PIN           -1
 
@@ -727,13 +734,25 @@
      //we have no buzzer installed
      #define BEEPER -1
      //LCD Pins
+	 	 #ifdef DOGLCD
+			 // Pins for DOGM SPI LCD Support
+			 #define DOGLCD_A0	30
+			 #define DOGLCD_CS	29
+			 // GLCD features
+			 #define LCD_CONTRAST 1
+			 // Uncomment screen orientation
+		     // #define LCD_SCREEN_ROT_0
+		     // #define LCD_SCREEN_ROT_90
+			 #define LCD_SCREEN_ROT_180
+		     // #define LCD_SCREEN_ROT_270
+			 #else // standard Hitachi LCD controller
 			 #define LCD_PINS_RS        4
 			 #define LCD_PINS_ENABLE    17
 			 #define LCD_PINS_D4        30
 			 #define LCD_PINS_D5        29
 			 #define LCD_PINS_D6        28
 			 #define LCD_PINS_D7        27
-     
+         #endif
      //The encoder and click button
      #define BTN_EN1 11  //must be a hardware interrupt pin
      #define BTN_EN2 10 //must be hardware interrupt pin