Merge remote-tracking branch 'remotes/upstream/Development' into Development
Conflicts: Marlin/Marlin_main.cpp Marlin/stepper.cpp
This commit is contained in:
domonoky
commit
d813090d90
|
|
@ -101,3 +101,25 @@
|
|||
* M908 - Control digital trimpot directly.
|
||||
* M928 - Start SD logging (M928 filename.g) - ended by M29
|
||||
* M999 - Restart after being stopped by error
|
||||
|
||||
# Comments
|
||||
|
||||
Comments start at a `;` (semicolon) and end with the end of the line:
|
||||
|
||||
N3 T0*57 ; This is a comment
|
||||
N4 G92 E0*67
|
||||
; So is this
|
||||
N5 G28*22
|
||||
|
||||
(example taken from the [RepRap wiki](http://reprap.org/wiki/Gcode#Comments))
|
||||
|
||||
If you need to use a literal `;` somewhere (for example within `M117`), you can escape semicolons with a `\`
|
||||
(backslash):
|
||||
|
||||
M117 Hello \;)
|
||||
|
||||
`\` can also be used to escape `\` itself, if you need a literal `\` in front of a `;`:
|
||||
|
||||
M117 backslash: \\;and a comment
|
||||
|
||||
Please note that hosts should strip any comments before sending GCODE to the printer in order to save bandwidth.
|
||||
|
|
@ -8,7 +8,7 @@
|
|||
//===========================================================================
|
||||
/*
|
||||
Here are some standard links for getting your machine calibrated:
|
||||
* http://reprap.org/wiki/Calibration
|
||||
* http://reprap.org/wiki/Calibration
|
||||
* http://youtu.be/wAL9d7FgInk
|
||||
* http://calculator.josefprusa.cz
|
||||
* http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
|
||||
|
|
@ -295,9 +295,12 @@ your extruder heater takes 2 minutes to hit the target on heating.
|
|||
//============================= Mechanical Settings =========================
|
||||
//===========================================================================
|
||||
|
||||
// Uncomment the following line to enable CoreXY kinematics
|
||||
// Uncomment this option to enable CoreXY kinematics
|
||||
// #define COREXY
|
||||
|
||||
// Enable this option for Toshiba steppers
|
||||
// #define CONFIG_STEPPERS_TOSHIBA
|
||||
|
||||
// coarse Endstop Settings
|
||||
#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
|
||||
|
||||
|
|
@ -382,40 +385,38 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
|
||||
#ifdef ENABLE_AUTO_BED_LEVELING
|
||||
|
||||
// There are 2 different ways to pick the X and Y locations to probe:
|
||||
|
||||
// - "grid" mode
|
||||
// Probe every point in a rectangular grid
|
||||
// You must specify the rectangle, and the density of sample points
|
||||
// This mode is preferred because there are more measurements.
|
||||
// It used to be called ACCURATE_BED_LEVELING but "grid" is more descriptive
|
||||
|
||||
// - "3-point" mode
|
||||
// Probe 3 arbitrary points on the bed (that aren't colinear)
|
||||
// You must specify the X & Y coordinates of all 3 points
|
||||
// There are 2 different ways to specify probing locations
|
||||
//
|
||||
// - "grid" mode
|
||||
// Probe several points in a rectangular grid.
|
||||
// You specify the rectangle and the density of sample points.
|
||||
// This mode is preferred because there are more measurements.
|
||||
//
|
||||
// - "3-point" mode
|
||||
// Probe 3 arbitrary points on the bed (that aren't colinear)
|
||||
// You specify the XY coordinates of all 3 points.
|
||||
|
||||
// Enable this to sample the bed in a grid (least squares solution)
|
||||
// Note: this feature generates 10KB extra code size
|
||||
#define AUTO_BED_LEVELING_GRID
|
||||
// with AUTO_BED_LEVELING_GRID, the bed is sampled in a
|
||||
// AUTO_BED_LEVELING_GRID_POINTSxAUTO_BED_LEVELING_GRID_POINTS grid
|
||||
// and least squares solution is calculated
|
||||
// Note: this feature occupies 10'206 byte
|
||||
|
||||
#ifdef AUTO_BED_LEVELING_GRID
|
||||
|
||||
// set the rectangle in which to probe
|
||||
// The edges of the rectangle in which to probe
|
||||
#define LEFT_PROBE_BED_POSITION 15
|
||||
#define RIGHT_PROBE_BED_POSITION 170
|
||||
#define BACK_PROBE_BED_POSITION 180
|
||||
#define FRONT_PROBE_BED_POSITION 20
|
||||
#define BACK_PROBE_BED_POSITION 170
|
||||
|
||||
// set the number of grid points per dimension
|
||||
// I wouldn't see a reason to go above 3 (=9 probing points on the bed)
|
||||
// Set the number of grid points per dimension
|
||||
// You probably don't need more than 3 (squared=9)
|
||||
#define AUTO_BED_LEVELING_GRID_POINTS 2
|
||||
|
||||
|
||||
#else // not AUTO_BED_LEVELING_GRID
|
||||
// with no grid, just probe 3 arbitrary points. A simple cross-product
|
||||
// is used to esimate the plane of the print bed
|
||||
#else // !AUTO_BED_LEVELING_GRID
|
||||
|
||||
// Arbitrary points to probe. A simple cross-product
|
||||
// is used to estimate the plane of the bed.
|
||||
#define ABL_PROBE_PT_1_X 15
|
||||
#define ABL_PROBE_PT_1_Y 180
|
||||
#define ABL_PROBE_PT_2_X 15
|
||||
|
|
@ -426,11 +427,11 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
#endif // AUTO_BED_LEVELING_GRID
|
||||
|
||||
|
||||
// these are the offsets to the probe relative to the extruder tip (Hotend - Probe)
|
||||
// Offsets to the probe relative to the extruder tip (Hotend - Probe)
|
||||
// X and Y offsets must be integers
|
||||
#define X_PROBE_OFFSET_FROM_EXTRUDER -25
|
||||
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29
|
||||
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35
|
||||
#define X_PROBE_OFFSET_FROM_EXTRUDER -25 // -left +right
|
||||
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // -front +behind
|
||||
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // -below (always!)
|
||||
|
||||
#define Z_RAISE_BEFORE_HOMING 4 // (in mm) Raise Z before homing (G28) for Probe Clearance.
|
||||
// Be sure you have this distance over your Z_MAX_POS in case
|
||||
|
|
@ -467,29 +468,6 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
|
||||
#endif
|
||||
|
||||
#ifdef AUTO_BED_LEVELING_GRID // Check if Probe_Offset * Grid Points is greater than Probing Range
|
||||
#if X_PROBE_OFFSET_FROM_EXTRUDER < 0
|
||||
#if (-(X_PROBE_OFFSET_FROM_EXTRUDER * (AUTO_BED_LEVELING_GRID_POINTS-1)) >= (RIGHT_PROBE_BED_POSITION - LEFT_PROBE_BED_POSITION))
|
||||
#error "The X axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS"
|
||||
#endif
|
||||
#else
|
||||
#if ((X_PROBE_OFFSET_FROM_EXTRUDER * (AUTO_BED_LEVELING_GRID_POINTS-1)) >= (RIGHT_PROBE_BED_POSITION - LEFT_PROBE_BED_POSITION))
|
||||
#error "The X axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS"
|
||||
#endif
|
||||
#endif
|
||||
#if Y_PROBE_OFFSET_FROM_EXTRUDER < 0
|
||||
#if (-(Y_PROBE_OFFSET_FROM_EXTRUDER * (AUTO_BED_LEVELING_GRID_POINTS-1)) >= (BACK_PROBE_BED_POSITION - FRONT_PROBE_BED_POSITION))
|
||||
#error "The Y axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS"
|
||||
#endif
|
||||
#else
|
||||
#if ((Y_PROBE_OFFSET_FROM_EXTRUDER * (AUTO_BED_LEVELING_GRID_POINTS-1)) >= (BACK_PROBE_BED_POSITION - FRONT_PROBE_BED_POSITION))
|
||||
#error "The Y axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS"
|
||||
#endif
|
||||
#endif
|
||||
|
||||
|
||||
#endif
|
||||
|
||||
#endif // ENABLE_AUTO_BED_LEVELING
|
||||
|
||||
|
||||
|
|
|
|||
|
|
@ -23,41 +23,41 @@
|
|||
#include "pins.h"
|
||||
|
||||
#ifndef AT90USB
|
||||
#define HardwareSerial_h // trick to disable the standard HWserial
|
||||
#define HardwareSerial_h // trick to disable the standard HWserial
|
||||
#endif
|
||||
|
||||
#if (ARDUINO >= 100)
|
||||
# include "Arduino.h"
|
||||
#include "Arduino.h"
|
||||
#else
|
||||
# include "WProgram.h"
|
||||
#include "WProgram.h"
|
||||
#endif
|
||||
|
||||
// Arduino < 1.0.0 does not define this, so we need to do it ourselves
|
||||
#ifndef analogInputToDigitalPin
|
||||
# define analogInputToDigitalPin(p) ((p) + 0xA0)
|
||||
#define analogInputToDigitalPin(p) ((p) + 0xA0)
|
||||
#endif
|
||||
|
||||
#ifdef AT90USB
|
||||
#include "HardwareSerial.h"
|
||||
#include "HardwareSerial.h"
|
||||
#endif
|
||||
|
||||
#include "MarlinSerial.h"
|
||||
|
||||
#ifndef cbi
|
||||
#define cbi(sfr, bit) (_SFR_BYTE(sfr) &= ~_BV(bit))
|
||||
#define cbi(sfr, bit) (_SFR_BYTE(sfr) &= ~_BV(bit))
|
||||
#endif
|
||||
#ifndef sbi
|
||||
#define sbi(sfr, bit) (_SFR_BYTE(sfr) |= _BV(bit))
|
||||
#define sbi(sfr, bit) (_SFR_BYTE(sfr) |= _BV(bit))
|
||||
#endif
|
||||
|
||||
#include "WString.h"
|
||||
|
||||
#ifdef AT90USB
|
||||
#ifdef BTENABLED
|
||||
#define MYSERIAL bt
|
||||
#else
|
||||
#define MYSERIAL Serial
|
||||
#endif // BTENABLED
|
||||
#ifdef BTENABLED
|
||||
#define MYSERIAL bt
|
||||
#else
|
||||
#define MYSERIAL Serial
|
||||
#endif // BTENABLED
|
||||
#else
|
||||
#define MYSERIAL MSerial
|
||||
#endif
|
||||
|
|
@ -86,7 +86,7 @@ extern const char echomagic[] PROGMEM;
|
|||
|
||||
#define SERIAL_ECHOPAIR(name,value) (serial_echopair_P(PSTR(name),(value)))
|
||||
|
||||
#define SERIAL_EOL SERIAL_ECHOLN("")
|
||||
#define SERIAL_EOL MYSERIAL.write('\n')
|
||||
|
||||
void serial_echopair_P(const char *s_P, float v);
|
||||
void serial_echopair_P(const char *s_P, double v);
|
||||
|
|
|
|||
File diff suppressed because it is too large
Load diff
|
|
@ -22,8 +22,7 @@ CardReader::CardReader() {
|
|||
autostart_index = 0;
|
||||
//power to SD reader
|
||||
#if SDPOWER > -1
|
||||
SET_OUTPUT(SDPOWER);
|
||||
WRITE(SDPOWER, HIGH);
|
||||
OUT_WRITE(SDPOWER, HIGH);
|
||||
#endif //SDPOWER
|
||||
|
||||
autostart_atmillis = millis() + 5000;
|
||||
|
|
|
|||
|
|
@ -21,17 +21,13 @@
|
|||
**/
|
||||
|
||||
#ifdef ULTIPANEL
|
||||
#define BLEN_A 0
|
||||
#define BLEN_B 1
|
||||
#define BLEN_C 2
|
||||
#define EN_A (1<<BLEN_A)
|
||||
#define EN_B (1<<BLEN_B)
|
||||
#define EN_C (1<<BLEN_C)
|
||||
#define encrot0 0
|
||||
#define encrot1 2
|
||||
#define encrot2 3
|
||||
#define encrot3 1
|
||||
#define LCD_CLICKED (buttons&EN_C)
|
||||
#define BLEN_A 0
|
||||
#define BLEN_B 1
|
||||
#define BLEN_C 2
|
||||
#define EN_A (1<<BLEN_A)
|
||||
#define EN_B (1<<BLEN_B)
|
||||
#define EN_C (1<<BLEN_C)
|
||||
#define LCD_CLICKED (buttons&EN_C)
|
||||
#endif
|
||||
|
||||
#include <U8glib.h>
|
||||
|
|
|
|||
|
|
@ -82,7 +82,7 @@ Here are some standard links for getting your machine calibrated:
|
|||
// #define PS_DEFAULT_OFF
|
||||
|
||||
//===========================================================================
|
||||
//============================= Thermal Settings ============================
|
||||
//============================= Thermal Settings ============================
|
||||
//===========================================================================
|
||||
//
|
||||
//--NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table
|
||||
|
|
@ -118,6 +118,10 @@ Here are some standard links for getting your machine calibrated:
|
|||
// 1010 is Pt1000 with 1k pullup (non standard)
|
||||
// 147 is Pt100 with 4k7 pullup
|
||||
// 110 is Pt100 with 1k pullup (non standard)
|
||||
// 998 and 999 are Dummy Tables. They will ALWAYS read 25°C or the temperature defined below.
|
||||
// Use it for Testing or Development purposes. NEVER for production machine.
|
||||
// #define DUMMY_THERMISTOR_998_VALUE 25
|
||||
// #define DUMMY_THERMISTOR_999_VALUE 100
|
||||
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -297,9 +301,12 @@ your extruder heater takes 2 minutes to hit the target on heating.
|
|||
//============================= Mechanical Settings =========================
|
||||
//===========================================================================
|
||||
|
||||
// Uncomment the following line to enable CoreXY kinematics
|
||||
// Uncomment this option to enable CoreXY kinematics
|
||||
// #define COREXY
|
||||
|
||||
// Enable this option for Toshiba steppers
|
||||
// #define CONFIG_STEPPERS_TOSHIBA
|
||||
|
||||
// coarse Endstop Settings
|
||||
#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
|
||||
|
||||
|
|
@ -332,11 +339,6 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
//#define DISABLE_MAX_ENDSTOPS
|
||||
//#define DISABLE_MIN_ENDSTOPS
|
||||
|
||||
// Disable max endstops for compatibility with endstop checking routine
|
||||
#if defined(COREXY) && !defined(DISABLE_MAX_ENDSTOPS)
|
||||
#define DISABLE_MAX_ENDSTOPS
|
||||
#endif
|
||||
|
||||
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
|
||||
#define X_ENABLE_ON 0
|
||||
#define Y_ENABLE_ON 0
|
||||
|
|
@ -389,40 +391,38 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
|
||||
#ifdef ENABLE_AUTO_BED_LEVELING
|
||||
|
||||
// There are 2 different ways to pick the X and Y locations to probe:
|
||||
|
||||
// - "grid" mode
|
||||
// Probe every point in a rectangular grid
|
||||
// You must specify the rectangle, and the density of sample points
|
||||
// This mode is preferred because there are more measurements.
|
||||
// It used to be called ACCURATE_BED_LEVELING but "grid" is more descriptive
|
||||
|
||||
// - "3-point" mode
|
||||
// Probe 3 arbitrary points on the bed (that aren't colinear)
|
||||
// You must specify the X & Y coordinates of all 3 points
|
||||
// There are 2 different ways to specify probing locations
|
||||
//
|
||||
// - "grid" mode
|
||||
// Probe several points in a rectangular grid.
|
||||
// You specify the rectangle and the density of sample points.
|
||||
// This mode is preferred because there are more measurements.
|
||||
//
|
||||
// - "3-point" mode
|
||||
// Probe 3 arbitrary points on the bed (that aren't colinear)
|
||||
// You specify the XY coordinates of all 3 points.
|
||||
|
||||
// Enable this to sample the bed in a grid (least squares solution)
|
||||
// Note: this feature generates 10KB extra code size
|
||||
#define AUTO_BED_LEVELING_GRID
|
||||
// with AUTO_BED_LEVELING_GRID, the bed is sampled in a
|
||||
// AUTO_BED_LEVELING_GRID_POINTSxAUTO_BED_LEVELING_GRID_POINTS grid
|
||||
// and least squares solution is calculated
|
||||
// Note: this feature occupies 10'206 byte
|
||||
|
||||
#ifdef AUTO_BED_LEVELING_GRID
|
||||
|
||||
// set the rectangle in which to probe
|
||||
// The edges of the rectangle in which to probe
|
||||
#define LEFT_PROBE_BED_POSITION 15
|
||||
#define RIGHT_PROBE_BED_POSITION 170
|
||||
#define BACK_PROBE_BED_POSITION 180
|
||||
#define FRONT_PROBE_BED_POSITION 20
|
||||
#define BACK_PROBE_BED_POSITION 170
|
||||
|
||||
// set the number of grid points per dimension
|
||||
// I wouldn't see a reason to go above 3 (=9 probing points on the bed)
|
||||
// Set the number of grid points per dimension
|
||||
// You probably don't need more than 3 (squared=9)
|
||||
#define AUTO_BED_LEVELING_GRID_POINTS 2
|
||||
|
||||
|
||||
#else // not AUTO_BED_LEVELING_GRID
|
||||
// with no grid, just probe 3 arbitrary points. A simple cross-product
|
||||
// is used to esimate the plane of the print bed
|
||||
#else // !AUTO_BED_LEVELING_GRID
|
||||
|
||||
// Arbitrary points to probe. A simple cross-product
|
||||
// is used to estimate the plane of the bed.
|
||||
#define ABL_PROBE_PT_1_X 15
|
||||
#define ABL_PROBE_PT_1_Y 180
|
||||
#define ABL_PROBE_PT_2_X 15
|
||||
|
|
@ -433,11 +433,11 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
#endif // AUTO_BED_LEVELING_GRID
|
||||
|
||||
|
||||
// these are the offsets to the probe relative to the extruder tip (Hotend - Probe)
|
||||
// Offsets to the probe relative to the extruder tip (Hotend - Probe)
|
||||
// X and Y offsets must be integers
|
||||
#define X_PROBE_OFFSET_FROM_EXTRUDER -25
|
||||
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29
|
||||
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35
|
||||
#define X_PROBE_OFFSET_FROM_EXTRUDER -25 // -left +right
|
||||
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // -front +behind
|
||||
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // -below (always!)
|
||||
|
||||
#define Z_RAISE_BEFORE_HOMING 4 // (in mm) Raise Z before homing (G28) for Probe Clearance.
|
||||
// Be sure you have this distance over your Z_MAX_POS in case
|
||||
|
|
@ -474,29 +474,6 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
|
||||
#endif
|
||||
|
||||
#ifdef AUTO_BED_LEVELING_GRID // Check if Probe_Offset * Grid Points is greater than Probing Range
|
||||
#if X_PROBE_OFFSET_FROM_EXTRUDER < 0
|
||||
#if (-(X_PROBE_OFFSET_FROM_EXTRUDER * (AUTO_BED_LEVELING_GRID_POINTS-1)) >= (RIGHT_PROBE_BED_POSITION - LEFT_PROBE_BED_POSITION))
|
||||
#error "The X axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS"
|
||||
#endif
|
||||
#else
|
||||
#if ((X_PROBE_OFFSET_FROM_EXTRUDER * (AUTO_BED_LEVELING_GRID_POINTS-1)) >= (RIGHT_PROBE_BED_POSITION - LEFT_PROBE_BED_POSITION))
|
||||
#error "The X axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS"
|
||||
#endif
|
||||
#endif
|
||||
#if Y_PROBE_OFFSET_FROM_EXTRUDER < 0
|
||||
#if (-(Y_PROBE_OFFSET_FROM_EXTRUDER * (AUTO_BED_LEVELING_GRID_POINTS-1)) >= (BACK_PROBE_BED_POSITION - FRONT_PROBE_BED_POSITION))
|
||||
#error "The Y axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS"
|
||||
#endif
|
||||
#else
|
||||
#if ((Y_PROBE_OFFSET_FROM_EXTRUDER * (AUTO_BED_LEVELING_GRID_POINTS-1)) >= (BACK_PROBE_BED_POSITION - FRONT_PROBE_BED_POSITION))
|
||||
#error "The Y axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS"
|
||||
#endif
|
||||
#endif
|
||||
|
||||
|
||||
#endif
|
||||
|
||||
#endif // ENABLE_AUTO_BED_LEVELING
|
||||
|
||||
|
||||
|
|
@ -536,9 +513,9 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
#define DEFAULT_EJERK 5.0 // (mm/sec)
|
||||
|
||||
|
||||
//===========================================================================
|
||||
//============================= Additional Features =========================
|
||||
//===========================================================================
|
||||
//=============================================================================
|
||||
//============================= Additional Features ===========================
|
||||
//=============================================================================
|
||||
|
||||
// Custom M code points
|
||||
#define CUSTOM_M_CODES
|
||||
|
|
@ -569,7 +546,12 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
#define ABS_PREHEAT_HPB_TEMP 100
|
||||
#define ABS_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
|
||||
|
||||
//LCD and SD support
|
||||
//==============================LCD and SD support=============================
|
||||
|
||||
// Define your display language below. Replace (en) with your language code and uncomment.
|
||||
// en, pl, fr, de, es, ru, it, pt, pt-br, fi, an, nl, ca, eu
|
||||
// See also language.h
|
||||
//#define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en)
|
||||
|
||||
// Character based displays can have different extended charsets.
|
||||
#define DISPLAY_CHARSET_HD44780_JAPAN // "ääööüüß23°"
|
||||
|
|
@ -583,7 +565,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
//#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder
|
||||
//#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking
|
||||
//#define ULTIMAKERCONTROLLER //as available from the Ultimaker online store.
|
||||
#define ULTIPANEL //the UltiPanel as on Thingiverse
|
||||
//#define ULTIPANEL //the UltiPanel as on Thingiverse
|
||||
//#define LCD_FEEDBACK_FREQUENCY_HZ 1000 // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
|
||||
//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
|
||||
|
||||
|
|
@ -750,7 +732,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
#define SDSUPPORT
|
||||
#define ULTRA_LCD
|
||||
#ifdef DOGLCD // Change number of lines to match the DOG graphic display
|
||||
#define LCD_WIDTH 20
|
||||
#define LCD_WIDTH 22
|
||||
#define LCD_HEIGHT 5
|
||||
#else
|
||||
#define LCD_WIDTH 20
|
||||
|
|
@ -759,7 +741,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
#else //no panel but just LCD
|
||||
#ifdef ULTRA_LCD
|
||||
#ifdef DOGLCD // Change number of lines to match the 128x64 graphics display
|
||||
#define LCD_WIDTH 20
|
||||
#define LCD_WIDTH 22
|
||||
#define LCD_HEIGHT 5
|
||||
#else
|
||||
#define LCD_WIDTH 16
|
||||
|
|
|
|||
|
|
@ -3,13 +3,12 @@
|
|||
|
||||
#include "boards.h"
|
||||
|
||||
|
||||
//===========================================================================
|
||||
//============================= Getting Started =============================
|
||||
//===========================================================================
|
||||
/*
|
||||
Here are some standard links for getting your machine calibrated:
|
||||
* http://reprap.org/wiki/Calibration
|
||||
* http://reprap.org/wiki/Calibration
|
||||
* http://youtu.be/wAL9d7FgInk
|
||||
* http://calculator.josefprusa.cz
|
||||
* http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
|
||||
|
|
@ -39,7 +38,7 @@ Here are some standard links for getting your machine calibrated:
|
|||
// User-specified version info of this build to display in [Pronterface, etc] terminal window during
|
||||
// startup. Implementation of an idea by Prof Braino to inform user that any changes made to this
|
||||
// build by the user have been successfully uploaded into firmware.
|
||||
#define STRING_VERSION "v1.0.2"
|
||||
#define STRING_VERSION "1.0.2"
|
||||
#define STRING_URL "reprap.org"
|
||||
#define STRING_VERSION_CONFIG_H __DATE__ " " __TIME__ // build date and time
|
||||
#define STRING_CONFIG_H_AUTHOR "(K8200, CONSULitAS)" // Who made the changes.
|
||||
|
|
@ -82,7 +81,6 @@ Here are some standard links for getting your machine calibrated:
|
|||
// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it.
|
||||
// #define PS_DEFAULT_OFF
|
||||
|
||||
|
||||
//===========================================================================
|
||||
//============================= Thermal Settings ============================
|
||||
//===========================================================================
|
||||
|
|
@ -120,6 +118,10 @@ Here are some standard links for getting your machine calibrated:
|
|||
// 1010 is Pt1000 with 1k pullup (non standard)
|
||||
// 147 is Pt100 with 4k7 pullup
|
||||
// 110 is Pt100 with 1k pullup (non standard)
|
||||
// 998 and 999 are Dummy Tables. They will ALWAYS read 25°C or the temperature defined below.
|
||||
// Use it for Testing or Development purposes. NEVER for production machine.
|
||||
// #define DUMMY_THERMISTOR_998_VALUE 25
|
||||
// #define DUMMY_THERMISTOR_999_VALUE 100
|
||||
|
||||
#define TEMP_SENSOR_0 5
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -260,7 +262,6 @@ Here are some standard links for getting your machine calibrated:
|
|||
#define EXTRUDE_MINTEMP 170
|
||||
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
|
||||
|
||||
|
||||
//===========================================================================
|
||||
//============================= Thermal Runaway Protection ==================
|
||||
//===========================================================================
|
||||
|
|
@ -305,9 +306,12 @@ your extruder heater takes 2 minutes to hit the target on heating.
|
|||
//============================= Mechanical Settings =========================
|
||||
//===========================================================================
|
||||
|
||||
// Uncomment the following line to enable CoreXY kinematics
|
||||
// Uncomment this option to enable CoreXY kinematics
|
||||
// #define COREXY
|
||||
|
||||
// Enable this option for Toshiba steppers
|
||||
// #define CONFIG_STEPPERS_TOSHIBA
|
||||
|
||||
// coarse Endstop Settings
|
||||
#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
|
||||
|
||||
|
|
@ -340,11 +344,6 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
#define DISABLE_MAX_ENDSTOPS
|
||||
//#define DISABLE_MIN_ENDSTOPS
|
||||
|
||||
// Disable max endstops for compatibility with endstop checking routine
|
||||
#if defined(COREXY) && !defined(DISABLE_MAX_ENDSTOPS)
|
||||
#define DISABLE_MAX_ENDSTOPS
|
||||
#endif
|
||||
|
||||
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
|
||||
#define X_ENABLE_ON 0
|
||||
#define Y_ENABLE_ON 0
|
||||
|
|
@ -397,40 +396,38 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
|
||||
#ifdef ENABLE_AUTO_BED_LEVELING
|
||||
|
||||
// There are 2 different ways to pick the X and Y locations to probe:
|
||||
|
||||
// - "grid" mode
|
||||
// Probe every point in a rectangular grid
|
||||
// You must specify the rectangle, and the density of sample points
|
||||
// This mode is preferred because there are more measurements.
|
||||
// It used to be called ACCURATE_BED_LEVELING but "grid" is more descriptive
|
||||
|
||||
// - "3-point" mode
|
||||
// Probe 3 arbitrary points on the bed (that aren't colinear)
|
||||
// You must specify the X & Y coordinates of all 3 points
|
||||
// There are 2 different ways to specify probing locations
|
||||
//
|
||||
// - "grid" mode
|
||||
// Probe several points in a rectangular grid.
|
||||
// You specify the rectangle and the density of sample points.
|
||||
// This mode is preferred because there are more measurements.
|
||||
//
|
||||
// - "3-point" mode
|
||||
// Probe 3 arbitrary points on the bed (that aren't colinear)
|
||||
// You specify the XY coordinates of all 3 points.
|
||||
|
||||
// Enable this to sample the bed in a grid (least squares solution)
|
||||
// Note: this feature generates 10KB extra code size
|
||||
#define AUTO_BED_LEVELING_GRID
|
||||
// with AUTO_BED_LEVELING_GRID, the bed is sampled in a
|
||||
// AUTO_BED_LEVELING_GRID_POINTSxAUTO_BED_LEVELING_GRID_POINTS grid
|
||||
// and least squares solution is calculated
|
||||
// Note: this feature occupies 10'206 byte
|
||||
|
||||
#ifdef AUTO_BED_LEVELING_GRID
|
||||
|
||||
// set the rectangle in which to probe
|
||||
// The edges of the rectangle in which to probe
|
||||
#define LEFT_PROBE_BED_POSITION 15
|
||||
#define RIGHT_PROBE_BED_POSITION 170
|
||||
#define BACK_PROBE_BED_POSITION 180
|
||||
#define FRONT_PROBE_BED_POSITION 20
|
||||
#define BACK_PROBE_BED_POSITION 170
|
||||
|
||||
// set the number of grid points per dimension
|
||||
// I wouldn't see a reason to go above 3 (=9 probing points on the bed)
|
||||
// Set the number of grid points per dimension
|
||||
// You probably don't need more than 3 (squared=9)
|
||||
#define AUTO_BED_LEVELING_GRID_POINTS 2
|
||||
|
||||
|
||||
#else // not AUTO_BED_LEVELING_GRID
|
||||
// with no grid, just probe 3 arbitrary points. A simple cross-product
|
||||
// is used to esimate the plane of the print bed
|
||||
#else // !AUTO_BED_LEVELING_GRID
|
||||
|
||||
// Arbitrary points to probe. A simple cross-product
|
||||
// is used to estimate the plane of the bed.
|
||||
#define ABL_PROBE_PT_1_X 15
|
||||
#define ABL_PROBE_PT_1_Y 180
|
||||
#define ABL_PROBE_PT_2_X 15
|
||||
|
|
@ -441,11 +438,11 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
#endif // AUTO_BED_LEVELING_GRID
|
||||
|
||||
|
||||
// these are the offsets to the probe relative to the extruder tip (Hotend - Probe)
|
||||
// Offsets to the probe relative to the extruder tip (Hotend - Probe)
|
||||
// X and Y offsets must be integers
|
||||
#define X_PROBE_OFFSET_FROM_EXTRUDER -25
|
||||
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29
|
||||
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35
|
||||
#define X_PROBE_OFFSET_FROM_EXTRUDER -25 // -left +right
|
||||
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // -front +behind
|
||||
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // -below (always!)
|
||||
|
||||
#define Z_RAISE_BEFORE_HOMING 4 // (in mm) Raise Z before homing (G28) for Probe Clearance.
|
||||
// Be sure you have this distance over your Z_MAX_POS in case
|
||||
|
|
@ -482,29 +479,6 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
|
||||
#endif
|
||||
|
||||
#ifdef AUTO_BED_LEVELING_GRID // Check if Probe_Offset * Grid Points is greater than Probing Range
|
||||
#if X_PROBE_OFFSET_FROM_EXTRUDER < 0
|
||||
#if (-(X_PROBE_OFFSET_FROM_EXTRUDER * (AUTO_BED_LEVELING_GRID_POINTS-1)) >= (RIGHT_PROBE_BED_POSITION - LEFT_PROBE_BED_POSITION))
|
||||
#error "The X axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS"
|
||||
#endif
|
||||
#else
|
||||
#if ((X_PROBE_OFFSET_FROM_EXTRUDER * (AUTO_BED_LEVELING_GRID_POINTS-1)) >= (RIGHT_PROBE_BED_POSITION - LEFT_PROBE_BED_POSITION))
|
||||
#error "The X axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS"
|
||||
#endif
|
||||
#endif
|
||||
#if Y_PROBE_OFFSET_FROM_EXTRUDER < 0
|
||||
#if (-(Y_PROBE_OFFSET_FROM_EXTRUDER * (AUTO_BED_LEVELING_GRID_POINTS-1)) >= (BACK_PROBE_BED_POSITION - FRONT_PROBE_BED_POSITION))
|
||||
#error "The Y axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS"
|
||||
#endif
|
||||
#else
|
||||
#if ((Y_PROBE_OFFSET_FROM_EXTRUDER * (AUTO_BED_LEVELING_GRID_POINTS-1)) >= (BACK_PROBE_BED_POSITION - FRONT_PROBE_BED_POSITION))
|
||||
#error "The Y axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS"
|
||||
#endif
|
||||
#endif
|
||||
|
||||
|
||||
#endif
|
||||
|
||||
#endif // ENABLE_AUTO_BED_LEVELING
|
||||
|
||||
|
||||
|
|
@ -544,9 +518,9 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
#define DEFAULT_EJERK 5.0 // (mm/sec)
|
||||
|
||||
|
||||
//===========================================================================
|
||||
//============================= Additional Features =========================
|
||||
//===========================================================================
|
||||
//=============================================================================
|
||||
//============================= Additional Features ===========================
|
||||
//=============================================================================
|
||||
|
||||
// Custom M code points
|
||||
#define CUSTOM_M_CODES
|
||||
|
|
@ -577,9 +551,12 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
#define ABS_PREHEAT_HPB_TEMP 60
|
||||
#define ABS_PREHEAT_FAN_SPEED 0 // Insert Value between 0 and 255
|
||||
|
||||
//LCD and SD support
|
||||
//==============================LCD and SD support=============================
|
||||
|
||||
// VM8201 (LCD Option for K8200) uses "DISPLAY_CHARSET_HD44870_JAPAN" and "ULTIMAKERCONTROLLER"
|
||||
// Define your display language below. Replace (en) with your language code and uncomment.
|
||||
// en, pl, fr, de, es, ru, it, pt, pt-br, fi, an, nl, ca, eu
|
||||
// See also language.h
|
||||
//#define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en)
|
||||
|
||||
// Character based displays can have different extended charsets.
|
||||
#define DISPLAY_CHARSET_HD44780_JAPAN // "ääööüüß23°"
|
||||
|
|
@ -760,7 +737,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
#define SDSUPPORT
|
||||
#define ULTRA_LCD
|
||||
#ifdef DOGLCD // Change number of lines to match the DOG graphic display
|
||||
#define LCD_WIDTH 20
|
||||
#define LCD_WIDTH 22
|
||||
#define LCD_HEIGHT 5
|
||||
#else
|
||||
#define LCD_WIDTH 20
|
||||
|
|
@ -769,7 +746,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
#else //no panel but just LCD
|
||||
#ifdef ULTRA_LCD
|
||||
#ifdef DOGLCD // Change number of lines to match the 128x64 graphics display
|
||||
#define LCD_WIDTH 20
|
||||
#define LCD_WIDTH 22
|
||||
#define LCD_HEIGHT 5
|
||||
#else
|
||||
#define LCD_WIDTH 16
|
||||
|
|
|
|||
|
|
@ -3,13 +3,12 @@
|
|||
|
||||
#include "boards.h"
|
||||
|
||||
|
||||
//===========================================================================
|
||||
//============================= Getting Started =============================
|
||||
//===========================================================================
|
||||
/*
|
||||
Here are some standard links for getting your machine calibrated:
|
||||
* http://reprap.org/wiki/Calibration
|
||||
* http://reprap.org/wiki/Calibration
|
||||
* http://youtu.be/wAL9d7FgInk
|
||||
* http://calculator.josefprusa.cz
|
||||
* http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
|
||||
|
|
@ -18,7 +17,6 @@ Here are some standard links for getting your machine calibrated:
|
|||
* http://www.thingiverse.com/thing:298812
|
||||
*/
|
||||
|
||||
|
||||
// This configuration file contains the basic settings.
|
||||
// Advanced settings can be found in Configuration_adv.h
|
||||
// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
|
||||
|
|
@ -52,7 +50,7 @@ Here are some standard links for getting your machine calibrated:
|
|||
#define L2_2 sq(Linkage_2) // do not change
|
||||
|
||||
//===========================================================================
|
||||
//========================= SCARA Settings end ==================================
|
||||
//========================= SCARA Settings end ==============================
|
||||
//===========================================================================
|
||||
|
||||
// User-specified version info of this build to display in [Pronterface, etc] terminal window during
|
||||
|
|
@ -70,7 +68,6 @@ Here are some standard links for getting your machine calibrated:
|
|||
// Serial port 0 is still used by the Arduino bootloader regardless of this setting.
|
||||
#define SERIAL_PORT 0
|
||||
|
||||
// This determines the communication speed of the printer
|
||||
// This determines the communication speed of the printer
|
||||
#define BAUDRATE 250000
|
||||
|
||||
|
|
@ -125,6 +122,7 @@ Here are some standard links for getting your machine calibrated:
|
|||
// 10 is 100k RS thermistor 198-961 (4.7k pullup)
|
||||
// 11 is 100k beta 3950 1% thermistor (4.7k pullup)
|
||||
// 12 is 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
|
||||
// 13 is 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE"
|
||||
// 20 is the PT100 circuit found in the Ultimainboard V2.x
|
||||
// 60 is 100k Maker's Tool Works Kapton Bed Thermistor beta=3950
|
||||
//
|
||||
|
|
@ -138,6 +136,10 @@ Here are some standard links for getting your machine calibrated:
|
|||
// 1010 is Pt1000 with 1k pullup (non standard)
|
||||
// 147 is Pt100 with 4k7 pullup
|
||||
// 110 is Pt100 with 1k pullup (non standard)
|
||||
// 998 and 999 are Dummy Tables. They will ALWAYS read 25°C or the temperature defined below.
|
||||
// Use it for Testing or Development purposes. NEVER for production machine.
|
||||
// #define DUMMY_THERMISTOR_998_VALUE 25
|
||||
// #define DUMMY_THERMISTOR_999_VALUE 100
|
||||
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -189,31 +191,24 @@ Here are some standard links for getting your machine calibrated:
|
|||
// Comment the following line to disable PID and enable bang-bang.
|
||||
#define PIDTEMP
|
||||
#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
|
||||
#define PID_MAX 255 // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
|
||||
#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
|
||||
#ifdef PIDTEMP
|
||||
//#define PID_DEBUG // Sends debug data to the serial port.
|
||||
//#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
//#define PID_PARAMS_PER_EXTRUDER // Uses separate PID parameters for each extruder (useful for mismatched extruders)
|
||||
// Set/get with gcode: M301 E[extruder number, 0-2]
|
||||
#define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more then PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
#define PID_INTEGRAL_DRIVE_MAX 255 //limit for the integral term
|
||||
#define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term
|
||||
#define K1 0.95 //smoothing factor within the PID
|
||||
#define PID_dT ((OVERSAMPLENR * 8.0)/(F_CPU / 64.0 / 256.0)) //sampling period of the temperature routine
|
||||
#define PID_dT ((OVERSAMPLENR * 10.0)/(F_CPU / 64.0 / 256.0)) //sampling period of the temperature routine
|
||||
|
||||
// If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
|
||||
// Ultimaker
|
||||
// #define DEFAULT_Kp 22.2
|
||||
// #define DEFAULT_Ki 1.08
|
||||
// #define DEFAULT_Kd 114
|
||||
|
||||
// Jhead MK5: From Autotune
|
||||
// #define DEFAULT_Kp 20.92
|
||||
// #define DEFAULT_Ki 1.51
|
||||
// #define DEFAULT_Kd 72.34
|
||||
|
||||
//Merlin Hotend: From Autotune
|
||||
#define DEFAULT_Kp 24.5
|
||||
#define DEFAULT_Ki 1.72
|
||||
#define DEFAULT_Kd 87.73
|
||||
// #define DEFAULT_Kp 22.2
|
||||
// #define DEFAULT_Ki 1.08
|
||||
// #define DEFAULT_Kd 114
|
||||
|
||||
// MakerGear
|
||||
// #define DEFAULT_Kp 7.0
|
||||
|
|
@ -221,9 +216,20 @@ Here are some standard links for getting your machine calibrated:
|
|||
// #define DEFAULT_Kd 12
|
||||
|
||||
// Mendel Parts V9 on 12V
|
||||
// #define DEFAULT_Kp 63.0
|
||||
// #define DEFAULT_Ki 2.25
|
||||
// #define DEFAULT_Kd 440
|
||||
// #define DEFAULT_Kp 63.0
|
||||
// #define DEFAULT_Ki 2.25
|
||||
// #define DEFAULT_Kd 440
|
||||
|
||||
// Jhead MK5: From Autotune
|
||||
// #define DEFAULT_Kp 20.92
|
||||
// #define DEFAULT_Ki 1.51
|
||||
// #define DEFAULT_Kd 72.34
|
||||
|
||||
// Merlin Hotend: From Autotune
|
||||
#define DEFAULT_Kp 24.5
|
||||
#define DEFAULT_Ki 1.72
|
||||
#define DEFAULT_Kd 87.73
|
||||
|
||||
#endif // PIDTEMP
|
||||
|
||||
//===========================================================================
|
||||
|
|
@ -251,9 +257,9 @@ Here are some standard links for getting your machine calibrated:
|
|||
#ifdef PIDTEMPBED
|
||||
//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
|
||||
//from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
|
||||
// #define DEFAULT_bedKp 10.00
|
||||
// #define DEFAULT_bedKi .023
|
||||
// #define DEFAULT_bedKd 305.4
|
||||
// #define DEFAULT_bedKp 10.00
|
||||
// #define DEFAULT_bedKi .023
|
||||
// #define DEFAULT_bedKd 305.4
|
||||
|
||||
//120v 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
|
||||
//from pidautotune
|
||||
|
|
@ -271,7 +277,6 @@ Here are some standard links for getting your machine calibrated:
|
|||
#endif // PIDTEMPBED
|
||||
|
||||
|
||||
|
||||
//this prevents dangerous Extruder moves, i.e. if the temperature is under the limit
|
||||
//can be software-disabled for whatever purposes by
|
||||
//#define PREVENT_DANGEROUS_EXTRUDE
|
||||
|
|
@ -281,7 +286,6 @@ Here are some standard links for getting your machine calibrated:
|
|||
#define EXTRUDE_MINTEMP 150
|
||||
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
|
||||
|
||||
|
||||
//===========================================================================
|
||||
//============================= Thermal Runaway Protection ==================
|
||||
//===========================================================================
|
||||
|
|
@ -323,12 +327,15 @@ your extruder heater takes 2 minutes to hit the target on heating.
|
|||
|
||||
|
||||
//===========================================================================
|
||||
//============================ Mechanical Settings ==========================
|
||||
//============================= Mechanical Settings =========================
|
||||
//===========================================================================
|
||||
|
||||
// Uncomment the following line to enable CoreXY kinematics
|
||||
// Uncomment this option to enable CoreXY kinematics
|
||||
// #define COREXY
|
||||
|
||||
// Enable this option for Toshiba steppers
|
||||
// #define CONFIG_STEPPERS_TOSHIBA
|
||||
|
||||
// coarse Endstop Settings
|
||||
//#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
|
||||
|
||||
|
|
@ -361,11 +368,6 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
//#define DISABLE_MAX_ENDSTOPS
|
||||
//#define DISABLE_MIN_ENDSTOPS
|
||||
|
||||
// Disable max endstops for compatibility with endstop checking routine
|
||||
#if defined(COREXY) && !defined(DISABLE_MAX_ENDSTOPS)
|
||||
#define DISABLE_MAX_ENDSTOPS
|
||||
#endif
|
||||
|
||||
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
|
||||
#define X_ENABLE_ON 0
|
||||
#define Y_ENABLE_ON 0
|
||||
|
|
@ -388,7 +390,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
#define INVERT_E3_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
|
||||
|
||||
// ENDSTOP SETTINGS:
|
||||
// Sets direction of endstop s when homing; 1=MAX, -1=MIN
|
||||
// Sets direction of endstops when homing; 1=MAX, -1=MIN
|
||||
#define X_HOME_DIR 1
|
||||
#define Y_HOME_DIR 1
|
||||
#define Z_HOME_DIR -1
|
||||
|
|
@ -414,43 +416,42 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
//===========================================================================
|
||||
|
||||
//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line)
|
||||
#define Z_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
|
||||
|
||||
#ifdef ENABLE_AUTO_BED_LEVELING
|
||||
|
||||
// There are 2 different ways to pick the X and Y locations to probe:
|
||||
|
||||
// - "grid" mode
|
||||
// Probe every point in a rectangular grid
|
||||
// You must specify the rectangle, and the density of sample points
|
||||
// This mode is preferred because there are more measurements.
|
||||
// It used to be called ACCURATE_BED_LEVELING but "grid" is more descriptive
|
||||
|
||||
// - "3-point" mode
|
||||
// Probe 3 arbitrary points on the bed (that aren't colinear)
|
||||
// You must specify the X & Y coordinates of all 3 points
|
||||
// There are 2 different ways to specify probing locations
|
||||
//
|
||||
// - "grid" mode
|
||||
// Probe several points in a rectangular grid.
|
||||
// You specify the rectangle and the density of sample points.
|
||||
// This mode is preferred because there are more measurements.
|
||||
//
|
||||
// - "3-point" mode
|
||||
// Probe 3 arbitrary points on the bed (that aren't colinear)
|
||||
// You specify the XY coordinates of all 3 points.
|
||||
|
||||
// Enable this to sample the bed in a grid (least squares solution)
|
||||
// Note: this feature generates 10KB extra code size
|
||||
#define AUTO_BED_LEVELING_GRID
|
||||
// with AUTO_BED_LEVELING_GRID, the bed is sampled in a
|
||||
// AUTO_BED_LEVELING_GRID_POINTSxAUTO_BED_LEVELING_GRID_POINTS grid
|
||||
// and least squares solution is calculated
|
||||
// Note: this feature occupies 10'206 byte
|
||||
|
||||
#ifdef AUTO_BED_LEVELING_GRID
|
||||
|
||||
// set the rectangle in which to probe
|
||||
// The edges of the rectangle in which to probe
|
||||
#define LEFT_PROBE_BED_POSITION 15
|
||||
#define RIGHT_PROBE_BED_POSITION 170
|
||||
#define BACK_PROBE_BED_POSITION 180
|
||||
#define FRONT_PROBE_BED_POSITION 20
|
||||
#define BACK_PROBE_BED_POSITION 170
|
||||
|
||||
// set the number of grid points per dimension
|
||||
// I wouldn't see a reason to go above 3 (=9 probing points on the bed)
|
||||
// Set the number of grid points per dimension
|
||||
// You probably don't need more than 3 (squared=9)
|
||||
#define AUTO_BED_LEVELING_GRID_POINTS 2
|
||||
|
||||
|
||||
#else // not AUTO_BED_LEVELING_GRID
|
||||
// with no grid, just probe 3 arbitrary points. A simple cross-product
|
||||
// is used to esimate the plane of the print bed
|
||||
#else // !AUTO_BED_LEVELING_GRID
|
||||
|
||||
// Arbitrary points to probe. A simple cross-product
|
||||
// is used to estimate the plane of the bed.
|
||||
#define ABL_PROBE_PT_1_X 15
|
||||
#define ABL_PROBE_PT_1_Y 180
|
||||
#define ABL_PROBE_PT_2_X 15
|
||||
|
|
@ -461,10 +462,11 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
#endif // AUTO_BED_LEVELING_GRID
|
||||
|
||||
|
||||
// these are the offsets to the probe relative to the extruder tip (Hotend - Probe)
|
||||
#define X_PROBE_OFFSET_FROM_EXTRUDER -25
|
||||
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29
|
||||
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35
|
||||
// Offsets to the probe relative to the extruder tip (Hotend - Probe)
|
||||
// X and Y offsets must be integers
|
||||
#define X_PROBE_OFFSET_FROM_EXTRUDER -25 // -left +right
|
||||
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // -front +behind
|
||||
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // -below (always!)
|
||||
|
||||
//#define Z_RAISE_BEFORE_HOMING 4 // (in mm) Raise Z before homing (G28) for Probe Clearance.
|
||||
// Be sure you have this distance over your Z_MAX_POS in case
|
||||
|
|
@ -474,6 +476,8 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
#define Z_RAISE_BEFORE_PROBING 15 //How much the extruder will be raised before traveling to the first probing point.
|
||||
#define Z_RAISE_BETWEEN_PROBINGS 5 //How much the extruder will be raised when traveling from between next probing points
|
||||
|
||||
//#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
|
||||
//#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
||||
|
||||
//If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk
|
||||
//The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it.
|
||||
|
|
@ -528,7 +532,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
#define DEFAULT_RETRACT_ACCELERATION 2000 // X, Y, Z and E max acceleration in mm/s^2 for retracts
|
||||
|
||||
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
|
||||
// The offset has to be X=0, Y=0 for extruder 0 hotend (default extruder).
|
||||
// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
|
||||
// For the other hotends it is their distance from the extruder 0 hotend.
|
||||
// #define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
|
||||
// #define EXTRUDER_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
|
||||
|
|
@ -539,9 +543,9 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
#define DEFAULT_EJERK 3 // (mm/sec)
|
||||
|
||||
|
||||
//===========================================================================
|
||||
//============================= Additional Features =========================
|
||||
//===========================================================================
|
||||
//=============================================================================
|
||||
//============================= Additional Features ===========================
|
||||
//=============================================================================
|
||||
|
||||
// Custom M code points
|
||||
//#define CUSTOM_M_CODES
|
||||
|
|
@ -572,7 +576,12 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
#define ABS_PREHEAT_HPB_TEMP 100
|
||||
#define ABS_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
|
||||
|
||||
//LCD and SD support
|
||||
//==============================LCD and SD support=============================
|
||||
|
||||
// Define your display language below. Replace (en) with your language code and uncomment.
|
||||
// en, pl, fr, de, es, ru, it, pt, pt-br, fi, an, nl, ca, eu
|
||||
// See also language.h
|
||||
//#define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en)
|
||||
|
||||
// Character based displays can have different extended charsets.
|
||||
#define DISPLAY_CHARSET_HD44780_JAPAN // "ääööüüß23°"
|
||||
|
|
@ -738,11 +747,13 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
// Shift register panels
|
||||
// ---------------------
|
||||
// 2 wire Non-latching LCD SR from:
|
||||
// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection
|
||||
//#define SR_LCD
|
||||
#ifdef SR_LCD
|
||||
#define SR_LCD_2W_NL // Non latching 2 wire shift register
|
||||
//#define NEWPANEL
|
||||
// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection
|
||||
|
||||
//#define SAV_3DLCD
|
||||
#ifdef SAV_3DLCD
|
||||
#define SR_LCD_2W_NL // Non latching 2 wire shiftregister
|
||||
#define NEWPANEL
|
||||
#define ULTIPANEL
|
||||
#endif
|
||||
|
||||
|
||||
|
|
@ -751,7 +762,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
#define SDSUPPORT
|
||||
#define ULTRA_LCD
|
||||
#ifdef DOGLCD // Change number of lines to match the DOG graphic display
|
||||
#define LCD_WIDTH 20
|
||||
#define LCD_WIDTH 22
|
||||
#define LCD_HEIGHT 5
|
||||
#else
|
||||
#define LCD_WIDTH 20
|
||||
|
|
@ -760,7 +771,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
#else //no panel but just LCD
|
||||
#ifdef ULTRA_LCD
|
||||
#ifdef DOGLCD // Change number of lines to match the 128x64 graphics display
|
||||
#define LCD_WIDTH 20
|
||||
#define LCD_WIDTH 22
|
||||
#define LCD_HEIGHT 5
|
||||
#else
|
||||
#define LCD_WIDTH 16
|
||||
|
|
@ -844,13 +855,13 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
// Uncomment below to enable
|
||||
//#define FILAMENT_SENSOR
|
||||
|
||||
#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2)
|
||||
#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel
|
||||
#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2)
|
||||
#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel
|
||||
|
||||
#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation
|
||||
#define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm
|
||||
#define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm
|
||||
#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM)
|
||||
#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM)
|
||||
|
||||
//defines used in the code
|
||||
#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially
|
||||
|
|
|
|||
|
|
@ -3,13 +3,12 @@
|
|||
|
||||
#include "boards.h"
|
||||
|
||||
|
||||
//===========================================================================
|
||||
//============================= Getting Started =============================
|
||||
//===========================================================================
|
||||
/*
|
||||
Here are some standard links for getting your machine calibrated:
|
||||
* http://reprap.org/wiki/Calibration
|
||||
* http://reprap.org/wiki/Calibration
|
||||
* http://youtu.be/wAL9d7FgInk
|
||||
* http://calculator.josefprusa.cz
|
||||
* http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
|
||||
|
|
@ -18,7 +17,6 @@ Here are some standard links for getting your machine calibrated:
|
|||
* http://www.thingiverse.com/thing:298812
|
||||
*/
|
||||
|
||||
|
||||
// This configuration file contains the basic settings.
|
||||
// Advanced settings can be found in Configuration_adv.h
|
||||
// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
|
||||
|
|
@ -83,7 +81,6 @@ Here are some standard links for getting your machine calibrated:
|
|||
// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it.
|
||||
// #define PS_DEFAULT_OFF
|
||||
|
||||
|
||||
//===========================================================================
|
||||
//============================= Thermal Settings ============================
|
||||
//===========================================================================
|
||||
|
|
@ -121,6 +118,10 @@ Here are some standard links for getting your machine calibrated:
|
|||
// 1010 is Pt1000 with 1k pullup (non standard)
|
||||
// 147 is Pt100 with 4k7 pullup
|
||||
// 110 is Pt100 with 1k pullup (non standard)
|
||||
// 998 and 999 are Dummy Tables. They will ALWAYS read 25°C or the temperature defined below.
|
||||
// Use it for Testing or Development purposes. NEVER for production machine.
|
||||
// #define DUMMY_THERMISTOR_998_VALUE 25
|
||||
// #define DUMMY_THERMISTOR_999_VALUE 100
|
||||
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -164,7 +165,6 @@ Here are some standard links for getting your machine calibrated:
|
|||
//#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=I^2/R
|
||||
//#define BED_WATTS (12.0*12.0/1.1) // P=I^2/R
|
||||
|
||||
|
||||
//===========================================================================
|
||||
//============================= PID Settings ================================
|
||||
//===========================================================================
|
||||
|
|
@ -184,7 +184,7 @@ Here are some standard links for getting your machine calibrated:
|
|||
// is more then PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
#define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term
|
||||
#define K1 0.95 //smoothing factor within the PID
|
||||
#define PID_dT ((OVERSAMPLENR * 8.0)/(F_CPU / 64.0 / 256.0)) //sampling period of the temperature routine
|
||||
#define PID_dT ((OVERSAMPLENR * 10.0)/(F_CPU / 64.0 / 256.0)) //sampling period of the temperature routine
|
||||
|
||||
// If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
|
||||
// Ultimaker
|
||||
|
|
@ -256,7 +256,6 @@ Here are some standard links for getting your machine calibrated:
|
|||
#define EXTRUDE_MINTEMP 170
|
||||
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
|
||||
|
||||
|
||||
//===========================================================================
|
||||
//============================= Thermal Runaway Protection ==================
|
||||
//===========================================================================
|
||||
|
|
@ -301,9 +300,12 @@ your extruder heater takes 2 minutes to hit the target on heating.
|
|||
//============================= Mechanical Settings =========================
|
||||
//===========================================================================
|
||||
|
||||
// Uncomment the following line to enable CoreXY kinematics
|
||||
// Uncomment this option to enable CoreXY kinematics
|
||||
// #define COREXY
|
||||
|
||||
// Enable this option for Toshiba steppers
|
||||
// #define CONFIG_STEPPERS_TOSHIBA
|
||||
|
||||
// coarse Endstop Settings
|
||||
#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
|
||||
|
||||
|
|
@ -336,11 +338,6 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
//#define DISABLE_MAX_ENDSTOPS
|
||||
//#define DISABLE_MIN_ENDSTOPS
|
||||
|
||||
// Disable max endstops for compatibility with endstop checking routine
|
||||
#if defined(COREXY) && !defined(DISABLE_MAX_ENDSTOPS)
|
||||
#define DISABLE_MAX_ENDSTOPS
|
||||
#endif
|
||||
|
||||
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
|
||||
#define X_ENABLE_ON 0
|
||||
#define Y_ENABLE_ON 0
|
||||
|
|
@ -393,40 +390,38 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
|
||||
#ifdef ENABLE_AUTO_BED_LEVELING
|
||||
|
||||
// There are 2 different ways to pick the X and Y locations to probe:
|
||||
|
||||
// - "grid" mode
|
||||
// Probe every point in a rectangular grid
|
||||
// You must specify the rectangle, and the density of sample points
|
||||
// This mode is preferred because there are more measurements.
|
||||
// It used to be called ACCURATE_BED_LEVELING but "grid" is more descriptive
|
||||
|
||||
// - "3-point" mode
|
||||
// Probe 3 arbitrary points on the bed (that aren't colinear)
|
||||
// You must specify the X & Y coordinates of all 3 points
|
||||
// There are 2 different ways to specify probing locations
|
||||
//
|
||||
// - "grid" mode
|
||||
// Probe several points in a rectangular grid.
|
||||
// You specify the rectangle and the density of sample points.
|
||||
// This mode is preferred because there are more measurements.
|
||||
//
|
||||
// - "3-point" mode
|
||||
// Probe 3 arbitrary points on the bed (that aren't colinear)
|
||||
// You specify the XY coordinates of all 3 points.
|
||||
|
||||
// Enable this to sample the bed in a grid (least squares solution)
|
||||
// Note: this feature generates 10KB extra code size
|
||||
#define AUTO_BED_LEVELING_GRID
|
||||
// with AUTO_BED_LEVELING_GRID, the bed is sampled in a
|
||||
// AUTO_BED_LEVELING_GRID_POINTSxAUTO_BED_LEVELING_GRID_POINTS grid
|
||||
// and least squares solution is calculated
|
||||
// Note: this feature occupies 10'206 byte
|
||||
|
||||
#ifdef AUTO_BED_LEVELING_GRID
|
||||
|
||||
// set the rectangle in which to probe
|
||||
// The edges of the rectangle in which to probe
|
||||
#define LEFT_PROBE_BED_POSITION 15
|
||||
#define RIGHT_PROBE_BED_POSITION 170
|
||||
#define BACK_PROBE_BED_POSITION 180
|
||||
#define FRONT_PROBE_BED_POSITION 20
|
||||
#define BACK_PROBE_BED_POSITION 170
|
||||
|
||||
// set the number of grid points per dimension
|
||||
// I wouldn't see a reason to go above 3 (=9 probing points on the bed)
|
||||
// Set the number of grid points per dimension
|
||||
// You probably don't need more than 3 (squared=9)
|
||||
#define AUTO_BED_LEVELING_GRID_POINTS 2
|
||||
|
||||
|
||||
#else // not AUTO_BED_LEVELING_GRID
|
||||
// with no grid, just probe 3 arbitrary points. A simple cross-product
|
||||
// is used to esimate the plane of the print bed
|
||||
#else // !AUTO_BED_LEVELING_GRID
|
||||
|
||||
// Arbitrary points to probe. A simple cross-product
|
||||
// is used to estimate the plane of the bed.
|
||||
#define ABL_PROBE_PT_1_X 15
|
||||
#define ABL_PROBE_PT_1_Y 180
|
||||
#define ABL_PROBE_PT_2_X 15
|
||||
|
|
@ -437,11 +432,11 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
#endif // AUTO_BED_LEVELING_GRID
|
||||
|
||||
|
||||
// these are the offsets to the probe relative to the extruder tip (Hotend - Probe)
|
||||
// Offsets to the probe relative to the extruder tip (Hotend - Probe)
|
||||
// X and Y offsets must be integers
|
||||
#define X_PROBE_OFFSET_FROM_EXTRUDER -25
|
||||
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29
|
||||
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35
|
||||
#define X_PROBE_OFFSET_FROM_EXTRUDER -25 // -left +right
|
||||
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // -front +behind
|
||||
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // -below (always!)
|
||||
|
||||
#define Z_RAISE_BEFORE_HOMING 4 // (in mm) Raise Z before homing (G28) for Probe Clearance.
|
||||
// Be sure you have this distance over your Z_MAX_POS in case
|
||||
|
|
@ -478,29 +473,6 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
|
||||
#endif
|
||||
|
||||
#ifdef AUTO_BED_LEVELING_GRID // Check if Probe_Offset * Grid Points is greater than Probing Range
|
||||
#if X_PROBE_OFFSET_FROM_EXTRUDER < 0
|
||||
#if (-(X_PROBE_OFFSET_FROM_EXTRUDER * (AUTO_BED_LEVELING_GRID_POINTS-1)) >= (RIGHT_PROBE_BED_POSITION - LEFT_PROBE_BED_POSITION))
|
||||
#error "The X axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS"
|
||||
#endif
|
||||
#else
|
||||
#if ((X_PROBE_OFFSET_FROM_EXTRUDER * (AUTO_BED_LEVELING_GRID_POINTS-1)) >= (RIGHT_PROBE_BED_POSITION - LEFT_PROBE_BED_POSITION))
|
||||
#error "The X axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS"
|
||||
#endif
|
||||
#endif
|
||||
#if Y_PROBE_OFFSET_FROM_EXTRUDER < 0
|
||||
#if (-(Y_PROBE_OFFSET_FROM_EXTRUDER * (AUTO_BED_LEVELING_GRID_POINTS-1)) >= (BACK_PROBE_BED_POSITION - FRONT_PROBE_BED_POSITION))
|
||||
#error "The Y axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS"
|
||||
#endif
|
||||
#else
|
||||
#if ((Y_PROBE_OFFSET_FROM_EXTRUDER * (AUTO_BED_LEVELING_GRID_POINTS-1)) >= (BACK_PROBE_BED_POSITION - FRONT_PROBE_BED_POSITION))
|
||||
#error "The Y axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS"
|
||||
#endif
|
||||
#endif
|
||||
|
||||
|
||||
#endif
|
||||
|
||||
#endif // ENABLE_AUTO_BED_LEVELING
|
||||
|
||||
|
||||
|
|
@ -540,9 +512,9 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
#define DEFAULT_EJERK 5.0 // (mm/sec)
|
||||
|
||||
|
||||
//===========================================================================
|
||||
//============================ Additional Features ==========================
|
||||
//===========================================================================
|
||||
//=============================================================================
|
||||
//============================= Additional Features ===========================
|
||||
//=============================================================================
|
||||
|
||||
// Custom M code points
|
||||
#define CUSTOM_M_CODES
|
||||
|
|
@ -573,7 +545,12 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
#define ABS_PREHEAT_HPB_TEMP 100
|
||||
#define ABS_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
|
||||
|
||||
//LCD and SD support
|
||||
//==============================LCD and SD support=============================
|
||||
|
||||
// Define your display language below. Replace (en) with your language code and uncomment.
|
||||
// en, pl, fr, de, es, ru, it, pt, pt-br, fi, an, nl, ca, eu
|
||||
// See also language.h
|
||||
//#define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en)
|
||||
|
||||
// Character based displays can have different extended charsets.
|
||||
#define DISPLAY_CHARSET_HD44780_JAPAN // "ääööüüß23°"
|
||||
|
|
@ -587,7 +564,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
//#define ENCODER_PULSES_PER_STEP 1 // Increase if you have a high resolution encoder
|
||||
//#define ENCODER_STEPS_PER_MENU_ITEM 5 // Set according to ENCODER_PULSES_PER_STEP or your liking
|
||||
//#define ULTIMAKERCONTROLLER //as available from the Ultimaker online store.
|
||||
#define ULTIPANEL //the UltiPanel as on Thingiverse
|
||||
//#define ULTIPANEL //the UltiPanel as on Thingiverse
|
||||
//#define LCD_FEEDBACK_FREQUENCY_HZ 1000 // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
|
||||
//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
|
||||
|
||||
|
|
@ -754,7 +731,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
#define SDSUPPORT
|
||||
#define ULTRA_LCD
|
||||
#ifdef DOGLCD // Change number of lines to match the DOG graphic display
|
||||
#define LCD_WIDTH 20
|
||||
#define LCD_WIDTH 22
|
||||
#define LCD_HEIGHT 5
|
||||
#else
|
||||
#define LCD_WIDTH 20
|
||||
|
|
@ -763,7 +740,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
#else //no panel but just LCD
|
||||
#ifdef ULTRA_LCD
|
||||
#ifdef DOGLCD // Change number of lines to match the 128x64 graphics display
|
||||
#define LCD_WIDTH 20
|
||||
#define LCD_WIDTH 22
|
||||
#define LCD_HEIGHT 5
|
||||
#else
|
||||
#define LCD_WIDTH 16
|
||||
|
|
|
|||
|
|
@ -1,15 +1,14 @@
|
|||
#ifndef CONFIGURATION_H
|
||||
#ifndef CONFIGURATION_H
|
||||
#define CONFIGURATION_H
|
||||
|
||||
#include "boards.h"
|
||||
|
||||
|
||||
//===========================================================================
|
||||
//============================= Getting Started =============================
|
||||
//===========================================================================
|
||||
/*
|
||||
Here are some standard links for getting your machine calibrated:
|
||||
* http://reprap.org/wiki/Calibration
|
||||
* http://reprap.org/wiki/Calibration
|
||||
* http://youtu.be/wAL9d7FgInk
|
||||
* http://calculator.josefprusa.cz
|
||||
* http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
|
||||
|
|
@ -22,7 +21,6 @@ Here are some standard links for getting your machine calibrated:
|
|||
// Advanced settings can be found in Configuration_adv.h
|
||||
// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
|
||||
|
||||
|
||||
//===========================================================================
|
||||
//============================= DELTA Printer ===============================
|
||||
//===========================================================================
|
||||
|
|
@ -30,6 +28,13 @@ Here are some standard links for getting your machine calibrated:
|
|||
// example_configurations/delta directory.
|
||||
//
|
||||
|
||||
//===========================================================================
|
||||
//============================= SCARA Printer ===============================
|
||||
//===========================================================================
|
||||
// For a Delta printer replace the configuration files with the files in the
|
||||
// example_configurations/SCARA directory.
|
||||
//
|
||||
|
||||
// User-specified version info of this build to display in [Pronterface, etc] terminal window during
|
||||
// startup. Implementation of an idea by Prof Braino to inform user that any changes made to this
|
||||
// build by the user have been successfully uploaded into firmware.
|
||||
|
|
@ -143,6 +148,10 @@ Here are some standard links for getting your machine calibrated:
|
|||
// 1010 is Pt1000 with 1k pullup (non standard)
|
||||
// 147 is Pt100 with 4k7 pullup
|
||||
// 110 is Pt100 with 1k pullup (non standard)
|
||||
// 998 and 999 are Dummy Tables. They will ALWAYS read 25°C or the temperature defined below.
|
||||
// Use it for Testing or Development purposes. NEVER for production machine.
|
||||
// #define DUMMY_THERMISTOR_998_VALUE 25
|
||||
// #define DUMMY_THERMISTOR_999_VALUE 100
|
||||
|
||||
#define TEMP_SENSOR_0 -1
|
||||
#define TEMP_SENSOR_1 -1
|
||||
|
|
@ -186,7 +195,6 @@ Here are some standard links for getting your machine calibrated:
|
|||
//#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=I^2/R
|
||||
//#define BED_WATTS (12.0*12.0/1.1) // P=I^2/R
|
||||
|
||||
|
||||
//===========================================================================
|
||||
//============================= PID Settings ================================
|
||||
//===========================================================================
|
||||
|
|
@ -195,13 +203,16 @@ Here are some standard links for getting your machine calibrated:
|
|||
// Comment the following line to disable PID and enable bang-bang.
|
||||
#define PIDTEMP
|
||||
#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
|
||||
#define PID_MAX 255 // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
|
||||
#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
|
||||
#ifdef PIDTEMP
|
||||
//#define PID_DEBUG // Sends debug data to the serial port.
|
||||
//#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
//#define PID_PARAMS_PER_EXTRUDER // Uses separate PID parameters for each extruder (useful for mismatched extruders)
|
||||
// Set/get with gcode: M301 E[extruder number, 0-2]
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more then PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
#define PID_INTEGRAL_DRIVE_MAX 255 //limit for the integral term
|
||||
#define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term
|
||||
#define K1 0.95 //smoothing factor within the PID
|
||||
#define PID_dT ((OVERSAMPLENR * 10.0)/(F_CPU / 64.0 / 256.0)) //sampling period of the temperature routine
|
||||
|
||||
|
|
@ -222,7 +233,6 @@ Here are some standard links for getting your machine calibrated:
|
|||
// #define DEFAULT_Kd 440
|
||||
#endif // PIDTEMP
|
||||
|
||||
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
|
|
@ -271,7 +281,6 @@ Here are some standard links for getting your machine calibrated:
|
|||
#define EXTRUDE_MINTEMP 170
|
||||
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
|
||||
|
||||
|
||||
//===========================================================================
|
||||
//============================= Thermal Runaway Protection ==================
|
||||
//===========================================================================
|
||||
|
|
@ -316,6 +325,12 @@ your extruder heater takes 2 minutes to hit the target on heating.
|
|||
//============================= Mechanical Settings =========================
|
||||
//===========================================================================
|
||||
|
||||
// Uncomment this option to enable CoreXY kinematics
|
||||
// #define COREXY
|
||||
|
||||
// Enable this option for Toshiba steppers
|
||||
// #define CONFIG_STEPPERS_TOSHIBA
|
||||
|
||||
// coarse Endstop Settings
|
||||
#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
|
||||
|
||||
|
|
@ -348,10 +363,6 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
//#define DISABLE_MAX_ENDSTOPS
|
||||
// Deltas never have min endstops
|
||||
#define DISABLE_MIN_ENDSTOPS
|
||||
// Disable max endstops for compatibility with endstop checking routine
|
||||
#if defined(COREXY) && !defined(DISABLE_MAX_ENDSTOPS)
|
||||
#define DISABLE_MAX_ENDSTOPS
|
||||
#endif
|
||||
|
||||
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
|
||||
#define X_ENABLE_ON 0
|
||||
|
|
@ -397,6 +408,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
#define Y_MAX_LENGTH (Y_MAX_POS - Y_MIN_POS)
|
||||
#define Z_MAX_LENGTH (Z_MAX_POS - Z_MIN_POS)
|
||||
|
||||
|
||||
//===========================================================================
|
||||
//============================= Bed Auto Leveling ===========================
|
||||
//===========================================================================
|
||||
|
|
@ -407,12 +419,10 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
|
||||
|
||||
// The position of the homing switches
|
||||
//#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used
|
||||
#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used
|
||||
//#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0)
|
||||
|
||||
//Manual homing switch locations:
|
||||
|
||||
#define MANUAL_HOME_POSITIONS // MANUAL_*_HOME_POS below will be used
|
||||
// For deltabots this means top and center of the Cartesian print volume.
|
||||
#define MANUAL_X_HOME_POS 0
|
||||
#define MANUAL_Y_HOME_POS 0
|
||||
|
|
@ -444,9 +454,10 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
#define DEFAULT_ZJERK 20.0 // (mm/sec) Must be same as XY for delta
|
||||
#define DEFAULT_EJERK 5.0 // (mm/sec)
|
||||
|
||||
//===========================================================================
|
||||
//============================= Additional Features =========================
|
||||
//===========================================================================
|
||||
|
||||
//=============================================================================
|
||||
//============================= Additional Features ===========================
|
||||
//=============================================================================
|
||||
|
||||
// Custom M code points
|
||||
#define CUSTOM_M_CODES
|
||||
|
|
@ -477,7 +488,12 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
#define ABS_PREHEAT_HPB_TEMP 100
|
||||
#define ABS_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
|
||||
|
||||
//LCD and SD support
|
||||
//==============================LCD and SD support=============================
|
||||
|
||||
// Define your display language below. Replace (en) with your language code and uncomment.
|
||||
// en, pl, fr, de, es, ru, it, pt, pt-br, fi, an, nl, ca, eu
|
||||
// See also language.h
|
||||
//#define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en)
|
||||
|
||||
// Character based displays can have different extended charsets.
|
||||
#define DISPLAY_CHARSET_HD44780_JAPAN // "ääööüüß23°"
|
||||
|
|
@ -650,11 +666,13 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
// Shift register panels
|
||||
// ---------------------
|
||||
// 2 wire Non-latching LCD SR from:
|
||||
// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection
|
||||
//#define SR_LCD
|
||||
#ifdef SR_LCD
|
||||
#define SR_LCD_2W_NL // Non latching 2 wire shift register
|
||||
//#define NEWPANEL
|
||||
// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection
|
||||
|
||||
//#define SAV_3DLCD
|
||||
#ifdef SAV_3DLCD
|
||||
#define SR_LCD_2W_NL // Non latching 2 wire shiftregister
|
||||
#define NEWPANEL
|
||||
#define ULTIPANEL
|
||||
#endif
|
||||
|
||||
|
||||
|
|
@ -663,7 +681,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
#define SDSUPPORT
|
||||
#define ULTRA_LCD
|
||||
#ifdef DOGLCD // Change number of lines to match the DOG graphic display
|
||||
#define LCD_WIDTH 20
|
||||
#define LCD_WIDTH 22
|
||||
#define LCD_HEIGHT 5
|
||||
#else
|
||||
#define LCD_WIDTH 20
|
||||
|
|
@ -672,7 +690,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
#else //no panel but just LCD
|
||||
#ifdef ULTRA_LCD
|
||||
#ifdef DOGLCD // Change number of lines to match the 128x64 graphics display
|
||||
#define LCD_WIDTH 20
|
||||
#define LCD_WIDTH 22
|
||||
#define LCD_HEIGHT 5
|
||||
#else
|
||||
#define LCD_WIDTH 16
|
||||
|
|
@ -756,13 +774,13 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
// Uncomment below to enable
|
||||
//#define FILAMENT_SENSOR
|
||||
|
||||
#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2)
|
||||
#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel
|
||||
#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2)
|
||||
#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel
|
||||
|
||||
#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation
|
||||
#define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm
|
||||
#define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm
|
||||
#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM)
|
||||
#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM)
|
||||
|
||||
//defines used in the code
|
||||
#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially
|
||||
|
|
@ -775,7 +793,6 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
|
||||
|
||||
|
||||
|
||||
#include "Configuration_adv.h"
|
||||
#include "thermistortables.h"
|
||||
|
||||
|
|
|
|||
|
|
@ -3,13 +3,12 @@
|
|||
|
||||
#include "boards.h"
|
||||
|
||||
|
||||
//===========================================================================
|
||||
//============================= Getting Started =============================
|
||||
//===========================================================================
|
||||
/*
|
||||
Here are some standard links for getting your machine calibrated:
|
||||
* http://reprap.org/wiki/Calibration
|
||||
* http://reprap.org/wiki/Calibration
|
||||
* http://youtu.be/wAL9d7FgInk
|
||||
* http://calculator.josefprusa.cz
|
||||
* http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
|
||||
|
|
@ -18,12 +17,10 @@ Here are some standard links for getting your machine calibrated:
|
|||
* http://www.thingiverse.com/thing:298812
|
||||
*/
|
||||
|
||||
|
||||
// This configuration file contains the basic settings.
|
||||
// Advanced settings can be found in Configuration_adv.h
|
||||
// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
|
||||
|
||||
|
||||
//===========================================================================
|
||||
//============================= DELTA Printer ===============================
|
||||
//===========================================================================
|
||||
|
|
@ -31,7 +28,6 @@ Here are some standard links for getting your machine calibrated:
|
|||
// example_configurations/delta directory.
|
||||
//
|
||||
|
||||
|
||||
//===========================================================================
|
||||
//============================= SCARA Printer ===============================
|
||||
//===========================================================================
|
||||
|
|
@ -85,7 +81,6 @@ Here are some standard links for getting your machine calibrated:
|
|||
// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it.
|
||||
// #define PS_DEFAULT_OFF
|
||||
|
||||
|
||||
//===========================================================================
|
||||
//============================= Thermal Settings ============================
|
||||
//===========================================================================
|
||||
|
|
@ -123,6 +118,10 @@ Here are some standard links for getting your machine calibrated:
|
|||
// 1010 is Pt1000 with 1k pullup (non standard)
|
||||
// 147 is Pt100 with 4k7 pullup
|
||||
// 110 is Pt100 with 1k pullup (non standard)
|
||||
// 998 and 999 are Dummy Tables. They will ALWAYS read 25°C or the temperature defined below.
|
||||
// Use it for Testing or Development purposes. NEVER for production machine.
|
||||
// #define DUMMY_THERMISTOR_998_VALUE 25
|
||||
// #define DUMMY_THERMISTOR_999_VALUE 100
|
||||
|
||||
#define TEMP_SENSOR_0 1
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -166,7 +165,6 @@ Here are some standard links for getting your machine calibrated:
|
|||
//#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=I^2/R
|
||||
//#define BED_WATTS (12.0*12.0/1.1) // P=I^2/R
|
||||
|
||||
|
||||
//===========================================================================
|
||||
//============================= PID Settings ================================
|
||||
//===========================================================================
|
||||
|
|
@ -175,13 +173,16 @@ Here are some standard links for getting your machine calibrated:
|
|||
// Comment the following line to disable PID and enable bang-bang.
|
||||
#define PIDTEMP
|
||||
#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
|
||||
#define PID_MAX 255 // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
|
||||
#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
|
||||
#ifdef PIDTEMP
|
||||
//#define PID_DEBUG // Sends debug data to the serial port.
|
||||
//#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
//#define PID_PARAMS_PER_EXTRUDER // Uses separate PID parameters for each extruder (useful for mismatched extruders)
|
||||
// Set/get with gcode: M301 E[extruder number, 0-2]
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more then PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
#define PID_INTEGRAL_DRIVE_MAX 255 //limit for the integral term
|
||||
#define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term
|
||||
#define K1 0.95 //smoothing factor within the PID
|
||||
#define PID_dT ((OVERSAMPLENR * 10.0)/(F_CPU / 64.0 / 256.0)) //sampling period of the temperature routine
|
||||
|
||||
|
|
@ -202,7 +203,6 @@ Here are some standard links for getting your machine calibrated:
|
|||
// #define DEFAULT_Kd 440
|
||||
#endif // PIDTEMP
|
||||
|
||||
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
|
|
@ -254,7 +254,6 @@ Here are some standard links for getting your machine calibrated:
|
|||
#define EXTRUDE_MINTEMP 170
|
||||
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
|
||||
|
||||
|
||||
//===========================================================================
|
||||
//============================= Thermal Runaway Protection ==================
|
||||
//===========================================================================
|
||||
|
|
@ -296,12 +295,15 @@ your extruder heater takes 2 minutes to hit the target on heating.
|
|||
|
||||
|
||||
//===========================================================================
|
||||
//============================ Mechanical Settings ==========================
|
||||
//============================= Mechanical Settings =========================
|
||||
//===========================================================================
|
||||
|
||||
// Uncomment the following line to enable CoreXY kinematics
|
||||
// Uncomment this option to enable CoreXY kinematics
|
||||
// #define COREXY
|
||||
|
||||
// Enable this option for Toshiba steppers
|
||||
// #define CONFIG_STEPPERS_TOSHIBA
|
||||
|
||||
// coarse Endstop Settings
|
||||
#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
|
||||
|
||||
|
|
@ -334,11 +336,6 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
//#define DISABLE_MAX_ENDSTOPS
|
||||
//#define DISABLE_MIN_ENDSTOPS
|
||||
|
||||
// Disable max endstops for compatibility with endstop checking routine
|
||||
#if defined(COREXY) && !defined(DISABLE_MAX_ENDSTOPS)
|
||||
#define DISABLE_MAX_ENDSTOPS
|
||||
#endif
|
||||
|
||||
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
|
||||
#define X_ENABLE_ON 0
|
||||
#define Y_ENABLE_ON 0
|
||||
|
|
@ -391,40 +388,38 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
|
||||
#ifdef ENABLE_AUTO_BED_LEVELING
|
||||
|
||||
// There are 2 different ways to pick the X and Y locations to probe:
|
||||
|
||||
// - "grid" mode
|
||||
// Probe every point in a rectangular grid
|
||||
// You must specify the rectangle, and the density of sample points
|
||||
// This mode is preferred because there are more measurements.
|
||||
// It used to be called ACCURATE_BED_LEVELING but "grid" is more descriptive
|
||||
|
||||
// - "3-point" mode
|
||||
// Probe 3 arbitrary points on the bed (that aren't colinear)
|
||||
// You must specify the X & Y coordinates of all 3 points
|
||||
// There are 2 different ways to specify probing locations
|
||||
//
|
||||
// - "grid" mode
|
||||
// Probe several points in a rectangular grid.
|
||||
// You specify the rectangle and the density of sample points.
|
||||
// This mode is preferred because there are more measurements.
|
||||
//
|
||||
// - "3-point" mode
|
||||
// Probe 3 arbitrary points on the bed (that aren't colinear)
|
||||
// You specify the XY coordinates of all 3 points.
|
||||
|
||||
// Enable this to sample the bed in a grid (least squares solution)
|
||||
// Note: this feature generates 10KB extra code size
|
||||
#define AUTO_BED_LEVELING_GRID
|
||||
// with AUTO_BED_LEVELING_GRID, the bed is sampled in a
|
||||
// AUTO_BED_LEVELING_GRID_POINTSxAUTO_BED_LEVELING_GRID_POINTS grid
|
||||
// and least squares solution is calculated
|
||||
// Note: this feature occupies 10'206 byte
|
||||
|
||||
#ifdef AUTO_BED_LEVELING_GRID
|
||||
|
||||
// set the rectangle in which to probe
|
||||
// The edges of the rectangle in which to probe
|
||||
#define LEFT_PROBE_BED_POSITION 15
|
||||
#define RIGHT_PROBE_BED_POSITION 170
|
||||
#define BACK_PROBE_BED_POSITION 180
|
||||
#define FRONT_PROBE_BED_POSITION 20
|
||||
#define BACK_PROBE_BED_POSITION 170
|
||||
|
||||
// set the number of grid points per dimension
|
||||
// I wouldn't see a reason to go above 3 (=9 probing points on the bed)
|
||||
// Set the number of grid points per dimension
|
||||
// You probably don't need more than 3 (squared=9)
|
||||
#define AUTO_BED_LEVELING_GRID_POINTS 2
|
||||
|
||||
|
||||
#else // not AUTO_BED_LEVELING_GRID
|
||||
// with no grid, just probe 3 arbitrary points. A simple cross-product
|
||||
// is used to esimate the plane of the print bed
|
||||
#else // !AUTO_BED_LEVELING_GRID
|
||||
|
||||
// Arbitrary points to probe. A simple cross-product
|
||||
// is used to estimate the plane of the bed.
|
||||
#define ABL_PROBE_PT_1_X 15
|
||||
#define ABL_PROBE_PT_1_Y 180
|
||||
#define ABL_PROBE_PT_2_X 15
|
||||
|
|
@ -435,10 +430,11 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
#endif // AUTO_BED_LEVELING_GRID
|
||||
|
||||
|
||||
// these are the offsets to the probe relative to the extruder tip (Hotend - Probe)
|
||||
#define X_PROBE_OFFSET_FROM_EXTRUDER -25
|
||||
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29
|
||||
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35
|
||||
// Offsets to the probe relative to the extruder tip (Hotend - Probe)
|
||||
// X and Y offsets must be integers
|
||||
#define X_PROBE_OFFSET_FROM_EXTRUDER -25 // -left +right
|
||||
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // -front +behind
|
||||
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // -below (always!)
|
||||
|
||||
#define Z_RAISE_BEFORE_HOMING 4 // (in mm) Raise Z before homing (G28) for Probe Clearance.
|
||||
// Be sure you have this distance over your Z_MAX_POS in case
|
||||
|
|
@ -514,9 +510,9 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
#define DEFAULT_EJERK 5.0 // (mm/sec)
|
||||
|
||||
|
||||
//===========================================================================
|
||||
//============================ Additional Features ==========================
|
||||
//===========================================================================
|
||||
//=============================================================================
|
||||
//============================= Additional Features ===========================
|
||||
//=============================================================================
|
||||
|
||||
// Custom M code points
|
||||
#define CUSTOM_M_CODES
|
||||
|
|
@ -547,7 +543,12 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
#define ABS_PREHEAT_HPB_TEMP 100
|
||||
#define ABS_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
|
||||
|
||||
//LCD and SD support
|
||||
//==============================LCD and SD support=============================
|
||||
|
||||
// Define your display language below. Replace (en) with your language code and uncomment.
|
||||
// en, pl, fr, de, es, ru, it, pt, pt-br, fi, an, nl, ca, eu
|
||||
// See also language.h
|
||||
//#define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en)
|
||||
|
||||
// Character based displays can have different extended charsets.
|
||||
#define DISPLAY_CHARSET_HD44780_JAPAN // "ääööüüß23°"
|
||||
|
|
@ -713,11 +714,13 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
// Shift register panels
|
||||
// ---------------------
|
||||
// 2 wire Non-latching LCD SR from:
|
||||
// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection
|
||||
//#define SR_LCD
|
||||
#ifdef SR_LCD
|
||||
#define SR_LCD_2W_NL // Non latching 2 wire shift register
|
||||
//#define NEWPANEL
|
||||
// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection
|
||||
|
||||
//#define SAV_3DLCD
|
||||
#ifdef SAV_3DLCD
|
||||
#define SR_LCD_2W_NL // Non latching 2 wire shiftregister
|
||||
#define NEWPANEL
|
||||
#define ULTIPANEL
|
||||
#endif
|
||||
|
||||
|
||||
|
|
@ -726,7 +729,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
#define SDSUPPORT
|
||||
#define ULTRA_LCD
|
||||
#ifdef DOGLCD // Change number of lines to match the DOG graphic display
|
||||
#define LCD_WIDTH 20
|
||||
#define LCD_WIDTH 22
|
||||
#define LCD_HEIGHT 5
|
||||
#else
|
||||
#define LCD_WIDTH 20
|
||||
|
|
@ -735,7 +738,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
#else //no panel but just LCD
|
||||
#ifdef ULTRA_LCD
|
||||
#ifdef DOGLCD // Change number of lines to match the 128x64 graphics display
|
||||
#define LCD_WIDTH 20
|
||||
#define LCD_WIDTH 22
|
||||
#define LCD_HEIGHT 5
|
||||
#else
|
||||
#define LCD_WIDTH 16
|
||||
|
|
|
|||
|
|
@ -8,7 +8,7 @@
|
|||
//===========================================================================
|
||||
/*
|
||||
Here are some standard links for getting your machine calibrated:
|
||||
* http://reprap.org/wiki/Calibration
|
||||
* http://reprap.org/wiki/Calibration
|
||||
* http://youtu.be/wAL9d7FgInk
|
||||
* http://calculator.josefprusa.cz
|
||||
* http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
|
||||
|
|
@ -17,12 +17,10 @@ Here are some standard links for getting your machine calibrated:
|
|||
* http://www.thingiverse.com/thing:298812
|
||||
*/
|
||||
|
||||
|
||||
// This configuration file contains the basic settings.
|
||||
// Advanced settings can be found in Configuration_adv.h
|
||||
// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
|
||||
|
||||
|
||||
//===========================================================================
|
||||
//============================= DELTA Printer ===============================
|
||||
//===========================================================================
|
||||
|
|
@ -30,7 +28,6 @@ Here are some standard links for getting your machine calibrated:
|
|||
// example_configurations/delta directory.
|
||||
//
|
||||
|
||||
|
||||
//===========================================================================
|
||||
//============================= SCARA Printer ===============================
|
||||
//===========================================================================
|
||||
|
|
@ -84,7 +81,6 @@ Here are some standard links for getting your machine calibrated:
|
|||
// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it.
|
||||
// #define PS_DEFAULT_OFF
|
||||
|
||||
|
||||
//===========================================================================
|
||||
//============================= Thermal Settings ============================
|
||||
//===========================================================================
|
||||
|
|
@ -122,6 +118,10 @@ Here are some standard links for getting your machine calibrated:
|
|||
// 1010 is Pt1000 with 1k pullup (non standard)
|
||||
// 147 is Pt100 with 4k7 pullup
|
||||
// 110 is Pt100 with 1k pullup (non standard)
|
||||
// 998 and 999 are Dummy Tables. They will ALWAYS read 25°C or the temperature defined below.
|
||||
// Use it for Testing or Development purposes. NEVER for production machine.
|
||||
// #define DUMMY_THERMISTOR_998_VALUE 25
|
||||
// #define DUMMY_THERMISTOR_999_VALUE 100
|
||||
|
||||
#define TEMP_SENSOR_0 5
|
||||
#define TEMP_SENSOR_1 0
|
||||
|
|
@ -156,8 +156,6 @@ Here are some standard links for getting your machine calibrated:
|
|||
#define HEATER_3_MAXTEMP 275
|
||||
#define BED_MAXTEMP 150
|
||||
|
||||
#define CONFIG_STEPPERS_TOSHIBA 1
|
||||
|
||||
// If your bed has low resistance e.g. .6 ohm and throws the fuse you can duty cycle it to reduce the
|
||||
// average current. The value should be an integer and the heat bed will be turned on for 1 interval of
|
||||
// HEATER_BED_DUTY_CYCLE_DIVIDER intervals.
|
||||
|
|
@ -167,7 +165,6 @@ Here are some standard links for getting your machine calibrated:
|
|||
//#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=I^2/R
|
||||
//#define BED_WATTS (12.0*12.0/1.1) // P=I^2/R
|
||||
|
||||
|
||||
//===========================================================================
|
||||
//============================= PID Settings ================================
|
||||
//===========================================================================
|
||||
|
|
@ -176,13 +173,16 @@ Here are some standard links for getting your machine calibrated:
|
|||
// Comment the following line to disable PID and enable bang-bang.
|
||||
#define PIDTEMP
|
||||
#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
|
||||
#define PID_MAX 255 // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
|
||||
#define PID_MAX BANG_MAX // limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
|
||||
#ifdef PIDTEMP
|
||||
//#define PID_DEBUG // Sends debug data to the serial port.
|
||||
//#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
//#define PID_PARAMS_PER_EXTRUDER // Uses separate PID parameters for each extruder (useful for mismatched extruders)
|
||||
// Set/get with gcode: M301 E[extruder number, 0-2]
|
||||
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
|
||||
// is more then PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
|
||||
#define PID_INTEGRAL_DRIVE_MAX 255 //limit for the integral term
|
||||
#define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term
|
||||
#define K1 0.95 //smoothing factor within the PID
|
||||
#define PID_dT ((OVERSAMPLENR * 10.0)/(F_CPU / 64.0 / 256.0)) //sampling period of the temperature routine
|
||||
|
||||
|
|
@ -208,7 +208,6 @@ Here are some standard links for getting your machine calibrated:
|
|||
// #define DEFAULT_Kd 440
|
||||
#endif // PIDTEMP
|
||||
|
||||
|
||||
//===========================================================================
|
||||
//============================= PID > Bed Temperature Control ===============
|
||||
//===========================================================================
|
||||
|
|
@ -257,7 +256,6 @@ Here are some standard links for getting your machine calibrated:
|
|||
#define EXTRUDE_MINTEMP 170
|
||||
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
|
||||
|
||||
|
||||
//===========================================================================
|
||||
//============================= Thermal Runaway Protection ==================
|
||||
//===========================================================================
|
||||
|
|
@ -299,12 +297,15 @@ your extruder heater takes 2 minutes to hit the target on heating.
|
|||
|
||||
|
||||
//===========================================================================
|
||||
//============================ Mechanical Settings ==========================
|
||||
//============================= Mechanical Settings =========================
|
||||
//===========================================================================
|
||||
|
||||
// Uncomment the following line to enable CoreXY kinematics
|
||||
// Uncomment this option to enable CoreXY kinematics
|
||||
// #define COREXY
|
||||
|
||||
// Enable this option for Toshiba steppers
|
||||
#define CONFIG_STEPPERS_TOSHIBA
|
||||
|
||||
// coarse Endstop Settings
|
||||
#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
|
||||
|
||||
|
|
@ -337,11 +338,6 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
//#define DISABLE_MAX_ENDSTOPS
|
||||
//#define DISABLE_MIN_ENDSTOPS
|
||||
|
||||
// Disable max endstops for compatibility with endstop checking routine
|
||||
#if defined(COREXY) && !defined(DISABLE_MAX_ENDSTOPS)
|
||||
#define DISABLE_MAX_ENDSTOPS
|
||||
#endif
|
||||
|
||||
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
|
||||
#define X_ENABLE_ON 1
|
||||
#define Y_ENABLE_ON 1
|
||||
|
|
@ -394,40 +390,38 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
|
||||
#ifdef ENABLE_AUTO_BED_LEVELING
|
||||
|
||||
// There are 2 different ways to pick the X and Y locations to probe:
|
||||
|
||||
// - "grid" mode
|
||||
// Probe every point in a rectangular grid
|
||||
// You must specify the rectangle, and the density of sample points
|
||||
// This mode is preferred because there are more measurements.
|
||||
// It used to be called ACCURATE_BED_LEVELING but "grid" is more descriptive
|
||||
|
||||
// - "3-point" mode
|
||||
// Probe 3 arbitrary points on the bed (that aren't colinear)
|
||||
// You must specify the X & Y coordinates of all 3 points
|
||||
// There are 2 different ways to specify probing locations
|
||||
//
|
||||
// - "grid" mode
|
||||
// Probe several points in a rectangular grid.
|
||||
// You specify the rectangle and the density of sample points.
|
||||
// This mode is preferred because there are more measurements.
|
||||
//
|
||||
// - "3-point" mode
|
||||
// Probe 3 arbitrary points on the bed (that aren't colinear)
|
||||
// You specify the XY coordinates of all 3 points.
|
||||
|
||||
// Enable this to sample the bed in a grid (least squares solution)
|
||||
// Note: this feature generates 10KB extra code size
|
||||
#define AUTO_BED_LEVELING_GRID
|
||||
// with AUTO_BED_LEVELING_GRID, the bed is sampled in a
|
||||
// AUTO_BED_LEVELING_GRID_POINTSxAUTO_BED_LEVELING_GRID_POINTS grid
|
||||
// and least squares solution is calculated
|
||||
// Note: this feature occupies 10'206 byte
|
||||
|
||||
#ifdef AUTO_BED_LEVELING_GRID
|
||||
|
||||
// set the rectangle in which to probe
|
||||
// The edges of the rectangle in which to probe
|
||||
#define LEFT_PROBE_BED_POSITION 15
|
||||
#define RIGHT_PROBE_BED_POSITION 170
|
||||
#define BACK_PROBE_BED_POSITION 180
|
||||
#define FRONT_PROBE_BED_POSITION 20
|
||||
#define BACK_PROBE_BED_POSITION 170
|
||||
|
||||
// set the number of grid points per dimension
|
||||
// I wouldn't see a reason to go above 3 (=9 probing points on the bed)
|
||||
// Set the number of grid points per dimension
|
||||
// You probably don't need more than 3 (squared=9)
|
||||
#define AUTO_BED_LEVELING_GRID_POINTS 2
|
||||
|
||||
|
||||
#else // not AUTO_BED_LEVELING_GRID
|
||||
// with no grid, just probe 3 arbitrary points. A simple cross-product
|
||||
// is used to esimate the plane of the print bed
|
||||
#else // !AUTO_BED_LEVELING_GRID
|
||||
|
||||
// Arbitrary points to probe. A simple cross-product
|
||||
// is used to estimate the plane of the bed.
|
||||
#define ABL_PROBE_PT_1_X 15
|
||||
#define ABL_PROBE_PT_1_Y 180
|
||||
#define ABL_PROBE_PT_2_X 15
|
||||
|
|
@ -438,10 +432,11 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
#endif // AUTO_BED_LEVELING_GRID
|
||||
|
||||
|
||||
// these are the offsets to the probe relative to the extruder tip (Hotend - Probe)
|
||||
#define X_PROBE_OFFSET_FROM_EXTRUDER -25
|
||||
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29
|
||||
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35
|
||||
// Offsets to the probe relative to the extruder tip (Hotend - Probe)
|
||||
// X and Y offsets must be integers
|
||||
#define X_PROBE_OFFSET_FROM_EXTRUDER -25 // -left +right
|
||||
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29 // -front +behind
|
||||
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35 // -below (always!)
|
||||
|
||||
#define Z_RAISE_BEFORE_HOMING 4 // (in mm) Raise Z before homing (G28) for Probe Clearance.
|
||||
// Be sure you have this distance over your Z_MAX_POS in case
|
||||
|
|
@ -498,21 +493,15 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
|
||||
// default settings
|
||||
|
||||
//#define DEFAULT_AXIS_STEPS_PER_UNIT {78.7402,78.7402,200.0*8/3,760*1.1} // default steps per unit for Ultimaker
|
||||
//#define //DEFAULT_AXIS_STEPS_PER_UNIT {79.87, 79.87, 2566, 563,78} // Al's TVRR
|
||||
//#define DEFAULT_AXIS_STEPS_PER_UNIT {79.87, 79.87, 2566, 563,78} // Al's TVRR
|
||||
//#define DEFAULT_AXIS_STEPS_PER_UNIT {81.26, 80.01, 2561, 599.14} // Michel TVRR old
|
||||
//#define DEFAULT_AXIS_STEPS_PER_UNIT {71.1, 71.1, 2560, 739.65} // Michel TVRR
|
||||
#define DEFAULT_AXIS_STEPS_PER_UNIT {71.1, 71.1, 2560, 600} // David TVRR
|
||||
|
||||
|
||||
|
||||
//#define DEFAULT_MAX_FEEDRATE {500, 500, 5, 25} // (mm/sec) default
|
||||
#define DEFAULT_MAX_FEEDRATE {500, 500, 5, 45} // (mm/sec) David TVRR
|
||||
#define DEFAULT_MAX_ACCELERATION {9000,9000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
|
||||
|
||||
/* MICHEL: This has an impact on the "ripples" in print walls */
|
||||
#define DEFAULT_ACCELERATION 500 // X, Y, Z and E max acceleration in mm/s^2 for printing moves
|
||||
//#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves
|
||||
#define DEFAULT_ACCELERATION 500 // X, Y, Z and E max acceleration in mm/s^2 for printing moves
|
||||
#define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for retracts
|
||||
|
||||
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
|
||||
|
|
@ -527,9 +516,9 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
#define DEFAULT_EJERK 5.0 // (mm/sec)
|
||||
|
||||
|
||||
//===========================================================================
|
||||
//============================ Additional Features ==========================
|
||||
//===========================================================================
|
||||
//=============================================================================
|
||||
//============================= Additional Features ===========================
|
||||
//=============================================================================
|
||||
|
||||
// Custom M code points
|
||||
#define CUSTOM_M_CODES
|
||||
|
|
@ -560,7 +549,12 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
#define ABS_PREHEAT_HPB_TEMP 100
|
||||
#define ABS_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255
|
||||
|
||||
//LCD and SD support
|
||||
//==============================LCD and SD support=============================
|
||||
|
||||
// Define your display language below. Replace (en) with your language code and uncomment.
|
||||
// en, pl, fr, de, es, ru, it, pt, pt-br, fi, an, nl, ca, eu
|
||||
// See also language.h
|
||||
//#define LANGUAGE_INCLUDE GENERATE_LANGUAGE_INCLUDE(en)
|
||||
|
||||
// Character based displays can have different extended charsets.
|
||||
#define DISPLAY_CHARSET_HD44780_JAPAN // "ääööüüß23°"
|
||||
|
|
@ -726,11 +720,13 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
// Shift register panels
|
||||
// ---------------------
|
||||
// 2 wire Non-latching LCD SR from:
|
||||
// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection
|
||||
//#define SR_LCD
|
||||
#ifdef SR_LCD
|
||||
#define SR_LCD_2W_NL // Non latching 2 wire shift register
|
||||
//#define NEWPANEL
|
||||
// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection
|
||||
|
||||
//#define SAV_3DLCD
|
||||
#ifdef SAV_3DLCD
|
||||
#define SR_LCD_2W_NL // Non latching 2 wire shiftregister
|
||||
#define NEWPANEL
|
||||
#define ULTIPANEL
|
||||
#endif
|
||||
|
||||
|
||||
|
|
@ -739,7 +735,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
#define SDSUPPORT
|
||||
#define ULTRA_LCD
|
||||
#ifdef DOGLCD // Change number of lines to match the DOG graphic display
|
||||
#define LCD_WIDTH 20
|
||||
#define LCD_WIDTH 22
|
||||
#define LCD_HEIGHT 5
|
||||
#else
|
||||
#define LCD_WIDTH 20
|
||||
|
|
@ -748,7 +744,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
#else //no panel but just LCD
|
||||
#ifdef ULTRA_LCD
|
||||
#ifdef DOGLCD // Change number of lines to match the 128x64 graphics display
|
||||
#define LCD_WIDTH 20
|
||||
#define LCD_WIDTH 22
|
||||
#define LCD_HEIGHT 5
|
||||
#else
|
||||
#define LCD_WIDTH 16
|
||||
|
|
@ -832,13 +828,13 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
|
|||
// Uncomment below to enable
|
||||
//#define FILAMENT_SENSOR
|
||||
|
||||
#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2)
|
||||
#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel
|
||||
#define FILAMENT_SENSOR_EXTRUDER_NUM 0 //The number of the extruder that has the filament sensor (0,1,2)
|
||||
#define MEASUREMENT_DELAY_CM 14 //measurement delay in cm. This is the distance from filament sensor to middle of barrel
|
||||
|
||||
#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm) - this is then used in the slicer software. Used for sensor reading validation
|
||||
#define MEASURED_UPPER_LIMIT 3.30 //upper limit factor used for sensor reading validation in mm
|
||||
#define MEASURED_LOWER_LIMIT 1.90 //lower limit factor for sensor reading validation in mm
|
||||
#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM)
|
||||
#define MAX_MEASUREMENT_DELAY 20 //delay buffer size in bytes (1 byte = 1cm)- limits maximum measurement delay allowable (must be larger than MEASUREMENT_DELAY_CM and lower number saves RAM)
|
||||
|
||||
//defines used in the code
|
||||
#define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA //set measured to nominal initially
|
||||
|
|
|
|||
|
|
@ -83,6 +83,9 @@
|
|||
/// check if pin is an timer wrapper
|
||||
#define GET_TIMER(IO) _GET_TIMER(IO)
|
||||
|
||||
// Shorthand
|
||||
#define OUT_WRITE(IO, v) { SET_OUTPUT(IO); WRITE(IO, v); }
|
||||
|
||||
/*
|
||||
ports and functions
|
||||
|
||||
|
|
|
|||
|
|
@ -121,6 +121,7 @@
|
|||
#define MSG_UNKNOWN_COMMAND "Unknown command: \""
|
||||
#define MSG_ACTIVE_EXTRUDER "Active Extruder: "
|
||||
#define MSG_INVALID_EXTRUDER "Invalid extruder"
|
||||
#define MSG_INVALID_SOLENOID "Invalid solenoid"
|
||||
#define MSG_X_MIN "x_min: "
|
||||
#define MSG_X_MAX "x_max: "
|
||||
#define MSG_Y_MIN "y_min: "
|
||||
|
|
@ -168,8 +169,8 @@
|
|||
#define MSG_PID_TIMEOUT MSG_PID_AUTOTUNE_FAILED " timeout"
|
||||
#define MSG_BIAS " bias: "
|
||||
#define MSG_D " d: "
|
||||
#define MSG_MIN " min: "
|
||||
#define MSG_MAX " max: "
|
||||
#define MSG_T_MIN " min: "
|
||||
#define MSG_T_MAX " max: "
|
||||
#define MSG_KU " Ku: "
|
||||
#define MSG_TU " Tu: "
|
||||
#define MSG_CLASSIC_PID " Classic PID "
|
||||
|
|
@ -225,8 +226,7 @@
|
|||
#define STR_h3 "3"
|
||||
#define STR_Deg "\271"
|
||||
#define STR_THERMOMETER "\002"
|
||||
#endif
|
||||
#ifdef DISPLAY_CHARSET_HD44780_WESTERN // HD44780 ROM Code: A02 (Western)
|
||||
#elif defined(DISPLAY_CHARSET_HD44780_WESTERN) // HD44780 ROM Code: A02 (Western)
|
||||
#define STR_Ae "\216"
|
||||
#define STR_ae "\204"
|
||||
#define STR_Oe "\211"
|
||||
|
|
@ -238,6 +238,8 @@
|
|||
#define STR_h3 "\263"
|
||||
#define STR_Deg "\337"
|
||||
#define STR_THERMOMETER "\002"
|
||||
#elif defined(ULTRA_LCD)
|
||||
#error You must enable either DISPLAY_CHARSET_HD44780_JAPAN or DISPLAY_CHARSET_HD44780_WESTERN for your LCD controller.
|
||||
#endif
|
||||
#endif
|
||||
/*
|
||||
|
|
|
|||
|
|
@ -87,9 +87,3 @@
|
|||
|
||||
// Cheaptronic v1.0 does not use this port
|
||||
#define SDCARDDETECT -1
|
||||
|
||||
// Encoder rotation values
|
||||
#define encrot0 0
|
||||
#define encrot1 2
|
||||
#define encrot2 3
|
||||
#define encrot3 1
|
||||
|
|
|
|||
|
|
@ -74,12 +74,6 @@
|
|||
#define BLEN_B 1
|
||||
#define BLEN_A 0
|
||||
|
||||
//encoder rotation values
|
||||
#define encrot0 0
|
||||
#define encrot1 2
|
||||
#define encrot2 3
|
||||
#define encrot3 1
|
||||
|
||||
#endif // RA_CONTROL_PANEL
|
||||
|
||||
#ifdef RA_DISCO
|
||||
|
|
|
|||
|
|
@ -83,10 +83,4 @@
|
|||
|
||||
#define SDCARDDETECT -1 // Ramps does not use this port
|
||||
|
||||
//encoder rotation values
|
||||
#define encrot0 0
|
||||
#define encrot1 2
|
||||
#define encrot2 3
|
||||
#define encrot3 1
|
||||
|
||||
#endif // ULTRA_LCD && NEWPANEL
|
||||
|
|
|
|||
|
|
@ -80,9 +80,3 @@
|
|||
#define BLEN_A 0
|
||||
|
||||
#define SDCARDDETECT -1 // Megatronics does not use this port
|
||||
|
||||
// Encoder rotation values
|
||||
#define encrot0 0
|
||||
#define encrot1 2
|
||||
#define encrot2 3
|
||||
#define encrot3 1
|
||||
|
|
|
|||
|
|
@ -95,9 +95,3 @@
|
|||
#define BLEN_A 0
|
||||
|
||||
#define SDCARDDETECT -1 // Megatronics does not use this port
|
||||
|
||||
// Encoder rotation values
|
||||
#define encrot0 0
|
||||
#define encrot1 2
|
||||
#define encrot2 3
|
||||
#define encrot3 1
|
||||
|
|
|
|||
|
|
@ -95,9 +95,3 @@
|
|||
#define BLEN_A 0
|
||||
|
||||
#define SDCARDDETECT -1 // Megatronics does not use this port
|
||||
|
||||
// Encoder rotation values
|
||||
#define encrot0 0
|
||||
#define encrot1 2
|
||||
#define encrot2 3
|
||||
#define encrot3 1
|
||||
|
|
|
|||
|
|
@ -116,11 +116,6 @@
|
|||
|
||||
#define SDCARDDETECT 81 // Ramps does not use this port
|
||||
|
||||
//encoder rotation values
|
||||
#define encrot0 0
|
||||
#define encrot1 2
|
||||
#define encrot2 3
|
||||
#define encrot3 1
|
||||
#else //!NEWPANEL - old style panel with shift register
|
||||
//arduino pin witch triggers an piezzo beeper
|
||||
#define BEEPER 33 No Beeper added
|
||||
|
|
@ -138,12 +133,6 @@
|
|||
#define LCD_PINS_D6 27
|
||||
#define LCD_PINS_D7 29
|
||||
|
||||
//encoder rotation values
|
||||
#define encrot0 0
|
||||
#define encrot1 2
|
||||
#define encrot2 3
|
||||
#define encrot3 1
|
||||
|
||||
//bits in the shift register that carry the buttons for:
|
||||
// left up center down right red
|
||||
#define BL_LE 7
|
||||
|
|
|
|||
|
|
@ -187,7 +187,7 @@ void checkHitEndstops()
|
|||
SERIAL_ECHOPAIR(" Z:",(float)endstops_trigsteps[Z_AXIS]/axis_steps_per_unit[Z_AXIS]);
|
||||
LCD_MESSAGEPGM(MSG_ENDSTOPS_HIT "Z");
|
||||
}
|
||||
SERIAL_ECHOLN("");
|
||||
SERIAL_EOL;
|
||||
endstop_x_hit=false;
|
||||
endstop_y_hit=false;
|
||||
endstop_z_hit=false;
|
||||
|
|
@ -554,54 +554,48 @@ ISR(TIMER1_COMPA_vect)
|
|||
#endif //ADVANCE
|
||||
|
||||
counter_x += current_block->steps_x;
|
||||
|
||||
#ifdef CONFIG_STEPPERS_TOSHIBA
|
||||
/* The toshiba stepper controller require much longer pulses
|
||||
* tjerfore we 'stage' decompose the pulses between high, and
|
||||
* low instead of doing each in turn. The extra tests add enough
|
||||
* lag to allow it work with without needing NOPs */
|
||||
if (counter_x > 0) {
|
||||
X_STEP_WRITE(HIGH);
|
||||
}
|
||||
/* The Toshiba stepper controller require much longer pulses.
|
||||
* So we 'stage' decompose the pulses between high and low
|
||||
* instead of doing each in turn. The extra tests add enough
|
||||
* lag to allow it work with without needing NOPs
|
||||
*/
|
||||
if (counter_x > 0) X_STEP_WRITE(HIGH);
|
||||
|
||||
counter_y += current_block->steps_y;
|
||||
if (counter_y > 0) {
|
||||
Y_STEP_WRITE( HIGH);
|
||||
}
|
||||
if (counter_y > 0) Y_STEP_WRITE(HIGH);
|
||||
|
||||
counter_z += current_block->steps_z;
|
||||
if (counter_z > 0) {
|
||||
Z_STEP_WRITE( HIGH);
|
||||
}
|
||||
if (counter_z > 0) Z_STEP_WRITE(HIGH);
|
||||
|
||||
#ifndef ADVANCE
|
||||
counter_e += current_block->steps_e;
|
||||
if (counter_e > 0) {
|
||||
WRITE_E_STEP(HIGH);
|
||||
}
|
||||
if (counter_e > 0) WRITE_E_STEP(HIGH);
|
||||
#endif //!ADVANCE
|
||||
|
||||
if (counter_x > 0) {
|
||||
counter_x -= current_block->step_event_count;
|
||||
count_position[X_AXIS]+=count_direction[X_AXIS];
|
||||
count_position[X_AXIS] += count_direction[X_AXIS];
|
||||
X_STEP_WRITE(LOW);
|
||||
}
|
||||
|
||||
if (counter_y > 0) {
|
||||
counter_y -= current_block->step_event_count;
|
||||
count_position[Y_AXIS]+=count_direction[Y_AXIS];
|
||||
count_position[Y_AXIS] += count_direction[Y_AXIS];
|
||||
Y_STEP_WRITE( LOW);
|
||||
}
|
||||
|
||||
if (counter_z > 0) {
|
||||
counter_z -= current_block->step_event_count;
|
||||
count_position[Z_AXIS]+=count_direction[Z_AXIS];
|
||||
count_position[Z_AXIS] += count_direction[Z_AXIS];
|
||||
Z_STEP_WRITE(LOW);
|
||||
}
|
||||
|
||||
#ifndef ADVANCE
|
||||
if (counter_e > 0) {
|
||||
counter_e -= current_block->step_event_count;
|
||||
count_position[E_AXIS]+=count_direction[E_AXIS];
|
||||
count_position[E_AXIS] += count_direction[E_AXIS];
|
||||
WRITE_E_STEP(LOW);
|
||||
}
|
||||
#endif //!ADVANCE
|
||||
|
|
@ -622,7 +616,7 @@ ISR(TIMER1_COMPA_vect)
|
|||
X_STEP_WRITE(!INVERT_X_STEP_PIN);
|
||||
#endif
|
||||
counter_x -= current_block->step_event_count;
|
||||
count_position[X_AXIS]+=count_direction[X_AXIS];
|
||||
count_position[X_AXIS] += count_direction[X_AXIS];
|
||||
#ifdef DUAL_X_CARRIAGE
|
||||
if (extruder_duplication_enabled){
|
||||
X_STEP_WRITE(INVERT_X_STEP_PIN);
|
||||
|
|
@ -648,7 +642,7 @@ ISR(TIMER1_COMPA_vect)
|
|||
#endif
|
||||
|
||||
counter_y -= current_block->step_event_count;
|
||||
count_position[Y_AXIS]+=count_direction[Y_AXIS];
|
||||
count_position[Y_AXIS] += count_direction[Y_AXIS];
|
||||
Y_STEP_WRITE(INVERT_Y_STEP_PIN);
|
||||
|
||||
#ifdef Y_DUAL_STEPPER_DRIVERS
|
||||
|
|
@ -659,15 +653,14 @@ ISR(TIMER1_COMPA_vect)
|
|||
counter_z += current_block->steps_z;
|
||||
if (counter_z > 0) {
|
||||
Z_STEP_WRITE( !INVERT_Z_STEP_PIN);
|
||||
|
||||
#ifdef Z_DUAL_STEPPER_DRIVERS
|
||||
Z2_STEP_WRITE(!INVERT_Z_STEP_PIN);
|
||||
#endif
|
||||
|
||||
counter_z -= current_block->step_event_count;
|
||||
count_position[Z_AXIS]+=count_direction[Z_AXIS];
|
||||
count_position[Z_AXIS] += count_direction[Z_AXIS];
|
||||
Z_STEP_WRITE( INVERT_Z_STEP_PIN);
|
||||
|
||||
|
||||
#ifdef Z_DUAL_STEPPER_DRIVERS
|
||||
Z2_STEP_WRITE(INVERT_Z_STEP_PIN);
|
||||
#endif
|
||||
|
|
@ -678,7 +671,7 @@ ISR(TIMER1_COMPA_vect)
|
|||
if (counter_e > 0) {
|
||||
WRITE_E_STEP(!INVERT_E_STEP_PIN);
|
||||
counter_e -= current_block->step_event_count;
|
||||
count_position[E_AXIS]+=count_direction[E_AXIS];
|
||||
count_position[E_AXIS] += count_direction[E_AXIS];
|
||||
WRITE_E_STEP(INVERT_E_STEP_PIN);
|
||||
}
|
||||
#endif //!ADVANCE
|
||||
|
|
|
|||
|
|
@ -296,8 +296,8 @@ void PID_autotune(float temp, int extruder, int ncycles)
|
|||
|
||||
SERIAL_PROTOCOLPGM(MSG_BIAS); SERIAL_PROTOCOL(bias);
|
||||
SERIAL_PROTOCOLPGM(MSG_D); SERIAL_PROTOCOL(d);
|
||||
SERIAL_PROTOCOLPGM(MSG_MIN); SERIAL_PROTOCOL(min);
|
||||
SERIAL_PROTOCOLPGM(MSG_MAX); SERIAL_PROTOCOLLN(max);
|
||||
SERIAL_PROTOCOLPGM(MSG_T_MIN); SERIAL_PROTOCOL(min);
|
||||
SERIAL_PROTOCOLPGM(MSG_T_MAX); SERIAL_PROTOCOLLN(max);
|
||||
if (cycles > 2) {
|
||||
Ku = (4.0 * d) / (3.14159265 * (max - min) / 2.0);
|
||||
Tu = ((float)(t_low + t_high) / 1000.0);
|
||||
|
|
@ -901,21 +901,15 @@ void tp_init()
|
|||
#ifdef HEATER_0_USES_MAX6675
|
||||
|
||||
#ifndef SDSUPPORT
|
||||
SET_OUTPUT(SCK_PIN);
|
||||
WRITE(SCK_PIN,0);
|
||||
|
||||
SET_OUTPUT(MOSI_PIN);
|
||||
WRITE(MOSI_PIN,1);
|
||||
|
||||
SET_INPUT(MISO_PIN);
|
||||
WRITE(MISO_PIN,1);
|
||||
OUT_WRITE(SCK_PIN, LOW);
|
||||
OUT_WRITE(MOSI_PIN, HIGH);
|
||||
OUT_WRITE(MISO_PIN, HIGH);
|
||||
#else
|
||||
pinMode(SS_PIN, OUTPUT);
|
||||
digitalWrite(SS_PIN, HIGH);
|
||||
#endif
|
||||
|
||||
SET_OUTPUT(MAX6675_SS);
|
||||
WRITE(MAX6675_SS,1);
|
||||
OUT_WRITE(MAX6675_SS,HIGH);
|
||||
|
||||
#endif //HEATER_0_USES_MAX6675
|
||||
|
||||
|
|
|
|||
|
|
@ -1394,6 +1394,17 @@ void lcd_reset_alert_level() { lcd_status_message_level = 0; }
|
|||
|
||||
#ifdef ULTIPANEL
|
||||
|
||||
////////////////////////
|
||||
// Setup Rotary Encoder Bit Values (for two pin encoders to indicate movement)
|
||||
// These values are independent of which pins are used for EN_A and EN_B indications
|
||||
// The rotary encoder part is also independent to the chipset used for the LCD
|
||||
#if defined(EN_A) && defined(EN_B)
|
||||
#define encrot0 0
|
||||
#define encrot1 2
|
||||
#define encrot2 3
|
||||
#define encrot3 1
|
||||
#endif
|
||||
|
||||
/* Warning: This function is called from interrupt context */
|
||||
void lcd_buttons_update() {
|
||||
#ifdef NEWPANEL
|
||||
|
|
|
|||
|
|
@ -123,17 +123,6 @@
|
|||
#define LCD_CLICKED (buttons&(B_MI|B_ST))
|
||||
#endif
|
||||
|
||||
////////////////////////
|
||||
// Setup Rotary Encoder Bit Values (for two pin encoders to indicate movement)
|
||||
// These values are independent of which pins are used for EN_A and EN_B indications
|
||||
// The rotary encoder part is also independent to the chipset used for the LCD
|
||||
#if defined(EN_A) && defined(EN_B)
|
||||
#define encrot0 0
|
||||
#define encrot1 2
|
||||
#define encrot2 3
|
||||
#define encrot3 1
|
||||
#endif
|
||||
|
||||
#endif //ULTIPANEL
|
||||
|
||||
////////////////////////////////////
|
||||
|
|
@ -832,32 +821,28 @@ static void lcd_implementation_drawmenu_sddirectory(uint8_t row, const char* pst
|
|||
|
||||
static void lcd_implementation_quick_feedback()
|
||||
{
|
||||
#ifdef LCD_USE_I2C_BUZZER
|
||||
#if !defined(LCD_FEEDBACK_FREQUENCY_HZ) || !defined(LCD_FEEDBACK_FREQUENCY_DURATION_MS)
|
||||
lcd_buzz(1000/6,100);
|
||||
#else
|
||||
lcd_buzz(LCD_FEEDBACK_FREQUENCY_DURATION_MS,LCD_FEEDBACK_FREQUENCY_HZ);
|
||||
#endif
|
||||
#elif defined(BEEPER) && BEEPER > -1
|
||||
SET_OUTPUT(BEEPER);
|
||||
#if !defined(LCD_FEEDBACK_FREQUENCY_HZ) || !defined(LCD_FEEDBACK_FREQUENCY_DURATION_MS)
|
||||
for(int8_t i=0;i<10;i++)
|
||||
{
|
||||
WRITE(BEEPER,HIGH);
|
||||
delayMicroseconds(100);
|
||||
WRITE(BEEPER,LOW);
|
||||
delayMicroseconds(100);
|
||||
}
|
||||
#ifdef LCD_USE_I2C_BUZZER
|
||||
#if defined(LCD_FEEDBACK_FREQUENCY_DURATION_MS) && defined(LCD_FEEDBACK_FREQUENCY_HZ)
|
||||
lcd_buzz(LCD_FEEDBACK_FREQUENCY_DURATION_MS, LCD_FEEDBACK_FREQUENCY_HZ);
|
||||
#else
|
||||
for(int8_t i=0;i<(LCD_FEEDBACK_FREQUENCY_DURATION_MS / (1000 / LCD_FEEDBACK_FREQUENCY_HZ));i++)
|
||||
{
|
||||
WRITE(BEEPER,HIGH);
|
||||
delayMicroseconds(1000000 / LCD_FEEDBACK_FREQUENCY_HZ / 2);
|
||||
WRITE(BEEPER,LOW);
|
||||
delayMicroseconds(1000000 / LCD_FEEDBACK_FREQUENCY_HZ / 2);
|
||||
}
|
||||
lcd_buzz(1000/6, 100);
|
||||
#endif
|
||||
#endif
|
||||
#elif defined(BEEPER) && BEEPER > -1
|
||||
SET_OUTPUT(BEEPER);
|
||||
#if !defined(LCD_FEEDBACK_FREQUENCY_HZ) || !defined(LCD_FEEDBACK_FREQUENCY_DURATION_MS)
|
||||
const unsigned int delay = 100;
|
||||
uint8_t i = 10;
|
||||
#else
|
||||
const unsigned int delay = 1000000 / LCD_FEEDBACK_FREQUENCY_HZ / 2;
|
||||
int8_t i = LCD_FEEDBACK_FREQUENCY_DURATION_MS * LCD_FEEDBACK_FREQUENCY_HZ / 1000;
|
||||
#endif
|
||||
while (i--) {
|
||||
WRITE(BEEPER,HIGH);
|
||||
delayMicroseconds(delay);
|
||||
WRITE(BEEPER,LOW);
|
||||
delayMicroseconds(delay);
|
||||
}
|
||||
#endif
|
||||
}
|
||||
|
||||
#ifdef LCD_HAS_STATUS_INDICATORS
|
||||
|
|
|
|||
|
|
@ -47,12 +47,9 @@ uint8_t u8g_dev_rrd_st7920_128x64_fn(u8g_t *u8g, u8g_dev_t *dev, uint8_t msg, vo
|
|||
{
|
||||
case U8G_DEV_MSG_INIT:
|
||||
{
|
||||
SET_OUTPUT(ST7920_CS_PIN);
|
||||
WRITE(ST7920_CS_PIN,0);
|
||||
SET_OUTPUT(ST7920_DAT_PIN);
|
||||
WRITE(ST7920_DAT_PIN,0);
|
||||
SET_OUTPUT(ST7920_CLK_PIN);
|
||||
WRITE(ST7920_CLK_PIN,1);
|
||||
OUT_WRITE(ST7920_CS_PIN,LOW);
|
||||
OUT_WRITE(ST7920_DAT_PIN,LOW);
|
||||
OUT_WRITE(ST7920_CLK_PIN,HIGH);
|
||||
|
||||
ST7920_CS();
|
||||
u8g_Delay(120); //initial delay for boot up
|
||||
|
|
|
|||
|
|
@ -84,7 +84,7 @@ void vector_3::debug(char* title)
|
|||
SERIAL_PROTOCOL(y);
|
||||
SERIAL_PROTOCOLPGM(" z: ");
|
||||
SERIAL_PROTOCOL(z);
|
||||
SERIAL_PROTOCOLPGM("\n");
|
||||
SERIAL_EOL;
|
||||
}
|
||||
|
||||
void apply_rotation_xyz(matrix_3x3 matrix, float &x, float& y, float& z)
|
||||
|
|
@ -145,22 +145,17 @@ matrix_3x3 matrix_3x3::transpose(matrix_3x3 original)
|
|||
return new_matrix;
|
||||
}
|
||||
|
||||
void matrix_3x3::debug(char* title)
|
||||
{
|
||||
SERIAL_PROTOCOL(title);
|
||||
SERIAL_PROTOCOL("\n");
|
||||
int count = 0;
|
||||
for(int i=0; i<3; i++)
|
||||
{
|
||||
for(int j=0; j<3; j++)
|
||||
{
|
||||
SERIAL_PROTOCOL(matrix[count]);
|
||||
SERIAL_PROTOCOLPGM(" ");
|
||||
count++;
|
||||
}
|
||||
|
||||
SERIAL_PROTOCOLPGM("\n");
|
||||
}
|
||||
void matrix_3x3::debug(char* title) {
|
||||
SERIAL_PROTOCOLLN(title);
|
||||
int count = 0;
|
||||
for(int i=0; i<3; i++) {
|
||||
for(int j=0; j<3; j++) {
|
||||
SERIAL_PROTOCOL(matrix[count] + 0.0001);
|
||||
SERIAL_PROTOCOLPGM(" ");
|
||||
count++;
|
||||
}
|
||||
SERIAL_EOL;
|
||||
}
|
||||
}
|
||||
|
||||
#endif // #ifdef ENABLE_AUTO_BED_LEVELING
|
||||
|
|
|
|||
|
|
@ -41,7 +41,7 @@ The current Marlin dev team consists of:
|
|||
|
||||
- Erik van der Zalm ([@ErikZalm](https://github.com/ErikZalm))
|
||||
- [@daid](https://github.com/daid)
|
||||
|
||||
|
||||
Sprinters lead developers are Kliment and caru.
|
||||
Grbls lead developer is Simen Svale Skogsrud.
|
||||
Sonney Jeon (Chamnit) improved some parts of grbl
|
||||
|
|
@ -52,9 +52,9 @@ More features have been added by:
|
|||
- Bradley Feldman,
|
||||
- and others...
|
||||
|
||||
## Licence
|
||||
## License
|
||||
|
||||
Marlin is published unde the [GPL license](/Documentation/COPYING.md) because I believe in open development.
|
||||
Marlin is published under the [GPL license](/Documentation/COPYING.md) because I believe in open development.
|
||||
Please do not use this code in products (3D printers, CNC etc) that are closed source or are crippled by a patent.
|
||||
|
||||
[](https://flattr.com/submit/auto?user_id=ErikZalm&url=https://github.com/MarlinFirmware/Marlin&title=Marlin&language=&tags=github&category=software)
|
||||
|
|
|
|||
Loading…
Reference in a new issue